Search Results

Search found 35371 results on 1415 pages for 'oracle technology network'.

Page 469/1415 | < Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >

  • Ubuntu Laptop as a wireless hotspot on bridge mode

    - by nixnotwin
    I have a wired router to which my ubuntu laptop connects via ethernet. The wierless NIC of the laptop acts as a wireless hotspot on master mode. I use hostapd fo this. I have bridged eth0 and wlan0, so my wireless clients that connect to my laptop over wifi get ip from the wired router via dhcp, so the devices get registered at the wired router ( and the laptop is just an access point). I use the following commands to get my laptop+accesspoint working: sudo brctl addbr br0 sudo brctl addif br0 eth0 sudo hostapd /etc/hostapd/hostapd.conf & sudo dhclient -d br0 & sudo ifconfig wlan0 192.168.1.15 netmask 255.255.255.0 up sudo brctl addif br0 wlan0 These commands enable me to access internet on my wireless clients and also on the laptop which is acting as wireless accesspoint. But if I reboot the wired router (without rebooting the laptop that is acting as accesspoint), Internet access on the laptop+accesspoint gets lost, but on wireless clients it works fine. Even I have not been able to figure out a command which will reset the laptop interfaces to default settings, so everytime the router reboots, I have to reboot the laptop too to get into default settings so that I can re-enter the above mentioned commands. My first question is How can I have my bridge+accesspoint up and running even-though the router reboots? And is there a command to set the interfaces to a default state? (ifdown -a doesn't work, after issuing the command the bridge still remained).

    Read the article

  • One Does Like To Code: DevoxxUK

    - by Tori Wieldt
    What's happening at Devoxx UK? I'll be talking to Rock Star speakers, Community leaders, authors, JSR leads and more.  This video is a short introduction.   Check out these great sessions: Thursday, June 12Perchance to Stream with Java 8by Paul Sandoz13:40 - 14:30 | Room 1 Making the Internet-of-Things a Reality with Embedded Javaby Simon Ritter11:50 - 12:40 | Room 4 Java SE 8 Lambdas and Streams Labby Simon Ritter17:00 - 20:00 | Room Mezzanine Safety Not Guaranteed: Sun. Misc. Unsafe and the Quest for Safe Alternativesby Paul Sandoz18:45 - 19:45 | Room 3 Join the Java EvolutionHeather VanCuraPatrick Curran19:45 – 20:45 | Room 2  Glassfish is Here to StayDavid DelabasseeAntonio Goncalves19:45 – 20:45 | Room Expo Here is the full line-up of sessions. Devoxx UK includes a Hackergarten, where can devs work an Open Source project of their choice. The Adopt OpenJDK and Adopt a JSR Program folks will be there to help attendees contribute back to Java SE and Java EE itself!   Saturday includes a special Devoxx4Kids event in conjunction with the London Java Community. It's design to teach 10-16 year-olds simple programming concepts, robotics, electronics, and games making. Workshops include LEGO Mindstorms (robotic engineering), Greenfoot (programming), Arduino (electronics), Scratch (games making), Minecraft Modding (game hacking) and NAO (robotic programming). Small fee, you must register. If you can't attend Devoxx UK in person, stay tuned to the YouTube/Java channel. I'll be doing plenty of interviews so you can join the fun from around the world. 

    Read the article

  • Tyrus 1.1

    - by Pavel Bucek
    It might seem like there is not much time passed since Tyrus 1.0 (Java API for WebSocket reference implementation) release, but the fact is it was frozen several weeks before going public and development in the trunk continued. Tyrus 1.1 brings some new features and improvements: client-side proxy support simple command line client various stability/performance fixes (see below for complete list) Individual blog posts about highlighted features will follow, same as related user guide chapters.. stay tuned! Tyrus 1.1 is already integrated in Glassfish trunk - you can download nightly build or upgrade to newer Tyrus manually (replace all Tyrus jars; I know this is not very user friendly, so I'll try to come up with some better solution or at least simple guide). Complete list of bugfixes/improvements: TYRUS-180 TYRUS-176 TYRUS-192 TYRUS-186 TYRUS-191 TYRUS-187 TYRUS-172 TYRUS-194 TYRUS-179 TYRUS-178 TYRUS-200 TYRUS-177 TYRUS-181 TYRUS-203 TYRUS-205 TYRUS-198 TYRUS-202 TYRUS-188 TYRUS-149 Related links: https://tyrus.java.net https://java.net/jira/browse/TYRUS/

    Read the article

  • How to use ipw3945 on Ubuntu 9.04

    - by Aaron
    Note: uname -a 2.6.28-16-generic cat /etc/issue Ubuntu 9.04 \n \l I have disabled iwl3945: cat /etc/modprobe.d/blacklist.conf | tail -3 blacklist iwl3945 blacklist mac8021 Question: How can I use iwp3945 instead?

    Read the article

  • Discount Multilingual Day in the Life of User Experience

    - by ultan o'broin
    Super article by the WikiMedia Foundation engineering folks about Designing for the Multilingual Web using the Wikipedia Universal Language Selector user interface as an example. Great ideas about tools that are available, as well as covering the basics of wireframing (mockups), prototyping, and user testing. Lots of inspiration there for developers and builders of apps who want to ensure their user experience (UX) really delivers for a global audience. Check out the use of the Firefox-based Pencil, how to translate your mockups, and how to perform remote user testing using Google+ Hangouts. Paul Giner demonstrates how to translate mockups. A little clunky and homespun in parts (I would prefer if tools such as Pencil or Balsamiq MockUps, and so on, could roundtrip directly from SVG to XLIFF for example, and Pencil doesn't work yet with the latest versions for Firefox) and I am not sure how it can really scales to enterprise-level use. However, the UX methodology is basically sound, and reinforces the importance of designing and testing in more that one language. The most powerful message for me is that you do not need special resources, training or expensive tools to deliver great-looking usable apps if you're a developer. Definitely worth considering if you're building apps out there in the community.

    Read the article

  • Gamification = -10#/3mo

    - by erikanollwebb
    One of the purposes of gamification of anything is to see if you can modify the behavior of the user. In the enterprise, that might mean getting sales people to enter more information into a CRM system, encouraging employees to update their HR records, motivating people to participate in forums and discussions, or process invoices more quickly.  Wikipedia defines behavior modification as "the traditional term for the use of empirically demonstrated behavior change techniques to increase or decrease the frequency of behaviors, such as altering an individual's behaviors and reactions to stimuli through positive and negative reinforcement of adaptive behavior and/or the reduction of behavior through its extinction, punishment and/or satiation."  Gamification is just a way to modify someone's behavior using game mechanics. And the magic question is always whether it works. So I thought I would present my own little experiment from the last few months.  This spring, I upgraded to a Samsung Galaxy 4.  It's a pretty sweet phone in many ways, but one of the little extras I discovered was a built in app called S Health. S Health is an app that you can use to track calories, weight, exercise and it has a built in pedometer. I looked at it when I got the phone, but assumed you had to turn it on to use it so I didn't look at it much.  But sometime in July, I realized that in fact, it just ran in the background and was quietly tracking my steps, with a goal of 10,000 per day.  10,000 steps per day is this magic number recommended by the Surgeon General and the American Heart Association.  Dr. Oz pushes it as the goal for daily exercise.  It's about 5 miles of walking. I'm generally not the kind of person who always has my phone with me.  I leave it in my purse and pull it out when I need it.  But then I realized that meant I wasn't getting a good measure of my steps.  I decided to do a little experiment, and carry it with me as much as possible for a week.  That's when I discovered the gamification that changed my life over the last 3 months.  When I hit 10,000 steps, the app jingled out a little "success!" tune and I got a badge.  I was hooked.  I started carrying my phone.  I started making sure I had shoes I could walk in with me.  I started walking at lunch time, because I realized how often I sat at my desk for 8-10 hours every day without moving.  I started pestering my husband to walk with me after work because I hadn't hit my 10,000 yet, leading him at one point to say "I'm not as much a slave to that badge as you are!"  I started looking at parking lots differently.  Can't get a space up close?  No worries, just that many steps toward my 10,000.  I even tried to see if there was a second power user level at 15,000 or 20,000 (*sadly, no).  If I was close at the end of the day, I have done laps around my house until I got my badge.  I have walked around the block one more time to get my badge.  I have mentally chastised myself when I forgot to put my phone in my pocket because I don't know how many steps I got.  The badge below I got when my boss and I were in New York City and we walked around the block of our hotel just to watch the badge pop up. There are a bunch of tools out on the market now that have similar ideas for helping you to track your exercise, make it social.  There are apps (my favorite is still Zombies, Run!).  You could buy a FitBit or UP by Jawbone.   Interactive fitness makes the Expresso stationary bike with built in video games.  All designed to help you be more aware of your activity and keep you engaged and motivated.  And the idea is to help you change your behavior. I know someone who would spend extra time and work hard on the Expresso because he had built up strategies for how to kill the most dragons while he was riding to get more points.  When the machine broke down, he didn't ride a different bike because it just wasn't that interesting. But for me, just the simple jingle and badge have been all I needed.  I admit, I still giggle gleefully when I hear the tune sing out from my pocket. After a few weeks, I noticed I had dropped a few pounds.  Not a lot, just 2-3.  But then I was really hooked.  I started making a point both to eat a little less and hit 10,000 steps as much as I could.  I bemoaned that during the floods in Boulder, I wasn't hitting my 10,000 steps.  And now, a few months later, I'm almost 10 lbs lighter. All for 1 badge a day. So yes, simple gamification can increase motivation and engagement.  And that can lead to changes in behavior.  Now the job is to apply that to the enterprise space in a meaningful and engaging way. 

    Read the article

  • How can I enable anonymous access to a Samba share under ADS security mode?

    - by hemp
    I'm trying to enable anonymous access to a single service in my Samba config. Authorized user access is working perfectly, but when I attempt a no-password connection, I get this message: Anonymous login successful Domain=[...] OS=[Unix] Server=[Samba 3.3.8-0.51.el5] tree connect failed: NT_STATUS_LOGON_FAILURE The message log shows this error: ... smbd[21262]: [2010/05/24 21:26:39, 0] smbd/service.c:make_connection_snum(1004) ... smbd[21262]: Can't become connected user! The smb.conf is configured thusly: [global] security = ads obey pam restrictions = Yes winbind enum users = Yes winbind enum groups = Yes winbind use default domain = true valid users = "@domain admins", "@domain users" guest account = nobody map to guest = Bad User [evilshare] path = /evil/share guest ok = yes read only = No browseable = No Given that I have 'map to guest = Bad User' and 'guest ok' specified, I don't understand why it is trying to "become connected user". Should it not be trying to "become guest user"?

    Read the article

  • Connecting two pcs through cable, at the same time as wireless

    - by Steffen
    I've got 2 pcs setup with WLAN - however when I copy files between the machines it takes forever (obviously, since I run 801.11g). So I thought, why not just connect them directly with a cable (my wireless router is the other end of the house, that's why I don't use cables to that) However how should I configure the LAN connection on each machine, so I can use it for transferring files between them, whilst using my WLAN to access the Internet ? I was thinking about letting one machine be gateway, but then Windows pops up with a lot of warnings (basically it says this won't work when you're using two disjoint networks) And now I'm at a loss as to what to try.

    Read the article

  • monitor multiple work repositories in ODI11g EM

    - by tina.wang
    when you create a domain, by default it will let you specify master/work repository information. This work repository is automatically configured and be directly monitored in EM But your master repository may contain multiple work repositories, how to let EM monitor all them. 1)these work repositories must have been registered in your master repository 2)in weblogic console, generate generic data source for every work repository, eg: jdbc/mySecondWork 3)in odiconsole, create new repository connection for the every work repository, master jndi information is jdbc/odiMasterRepository by default OK, now you can see the work repository status is configured. Btw, there is a bug when the work repository is execution type.

    Read the article

  • links for 2011-01-05

    - by Bob Rhubart
    A Role-Based Approach to Automated Provisioning and Personalized Portals Authors Rex Thexton (Managing Dir, PricewaterhouseCoopers), Nishidhdha Shah (Sr. Associate at PwC Consulting) and Harish Gaur (Dir. Product Management, Oracle Fusion Middleware) bring you the final article in the Fusion Middleware Patterns series. (tags: Oracle otn entarch enterprise2.0) 13 Jan 2011 - New York, NY - Coherence Special Interest Group - Oracle Coherence Knowledge Base The world's largest enterprise software company, Oracle is the only vendor to offer solutions for every tier of your business -- database, middleware, business intelligence, business applications, and collaboration. With Oracle, you get information that helps you measure results, improve business processes, and communicate a single truth to your constituents. (tags: ping.fm) Marc Kelderman: Exporting the SOA MDS Marc Kelderman show you how in this brief tutorial. (tags: oracle otn soa mds)

    Read the article

  • An Epic Question "How to call a method when the page loads"

    - by Arunkumar Ramamoorthy
    Quite often, there comes a question in OTN, with different subjects, all meaning "How to call a method when my ADF page loads?". More often, people tend to take the approach of ADF Phase Listener by overriding before/afterPhase methods.In this blog, we will go through different options in achieving it.1. Method Call Activity as default activity in Taskflow :If the application is built with taskflows, then this is the best suited approach to take. 1.a. Calling a Data Control Method :To call a Data Control method (ex: A method in AMImpl exposed as client interface), simply Drag and Drop the method as Default Method Call Activity, then draw a control flow case from the method to your page. Once after this, drop the taskflow as region in main page. When we run the main page, the Method Call Activity would be called first, and then the page will be rendered.1.b. Calling a Method in Backing Bean: To call a method in the backing bean before pageload, we can follow the similar approach as above. Instead of binding the Method Call Activity to an action/method binding in pagedef, we bind to the method. Insert a Method Call Activity (and make it as default) from the Component Palette. Double click on to select a method to bind. This approach can also be used, to perform some action in backing bean along with calling a method Data Control (just need to add bindings code in backing bean to execute DC method). 2. Using invokeAction Executable :If the application is built with pages and no taskflows are involved, then this option can be taken into consideration.In the page definition of the page, add an invokeAction Executable and bind it to the method needed to be executed. 3. Using combination of Server and Client Listeners : If the page does not have any page definition, then to call a method in backing bean, this approach can be taken. In this, a serverListener would be added at the document level, which would be calling the method in backing bean. Along with this, a clientListener would be added with "load" type (i.e will be triggered when the page loads), which would queue a serverEvent to trigger the method. 4. Using Page Phase Listener :This should be the last resort. Care should be taken when using this approach since the Phase Listener would be called for each request sent by the client.Zeeshan Baig's blog covers this scenario.

    Read the article

  • An Epic Question "How to call a method when the page loads"

    - by Arunkumar Ramamoorthy
    Quite often, there comes a question in OTN, with different subjects, all meaning "How to call a method when my ADF page loads?". More often, people tend to take the approach of ADF Phase Listener by overriding before/afterPhase methods.In this blog, we will go through different options in achieving it.1. Method Call Activity as default activity in Taskflow :If the application is built with taskflows, then this is the best suited approach to take. 1.a. Calling a Data Control Method :To call a Data Control method (ex: A method in AMImpl exposed as client interface), simply Drag and Drop the method as Default Method Call Activity, then draw a control flow case from the method to your page. Once after this, drop the taskflow as region in main page. When we run the main page, the Method Call Activity would be called first, and then the page will be rendered.1.b. Calling a Method in Backing Bean: To call a method in the backing bean before pageload, we can follow the similar approach as above. Instead of binding the Method Call Activity to an action/method binding in pagedef, we bind to the method. Insert a Method Call Activity (and make it as default) from the Component Palette. Double click on to select a method to bind. This approach can also be used, to perform some action in backing bean along with calling a method Data Control (just need to add bindings code in backing bean to execute DC method). 2. Using invokeAction Executable :If the application is built with pages and no taskflows are involved, then this option can be taken into consideration.In the page definition of the page, add an invokeAction Executable and bind it to the method needed to be executed. 3. Using combination of Server and Client Listeners : If the page does not have any page definition, then to call a method in backing bean, this approach can be taken. In this, a serverListener would be added at the document level, which would be calling the method in backing bean. Along with this, a clientListener would be added with "load" type (i.e will be triggered when the page loads), which would queue a serverEvent to trigger the method. 4. Using Page Phase Listener :This should be the last resort. Care should be taken when using this approach since the Phase Listener would be called for each request sent by the client.Zeeshan Baig's blog covers this scenario.

    Read the article

  • Common SOA Problems by C2B2

    - by JuergenKress
    SOA stands for Service Oriented Architecture and has only really come together as a concrete approach in the last 15 years or so, although the concepts involved have been around for longer. Oracle SOA Suite is based around the Service Component Architecture (SCA) devised by the Open SOA collaboration of companies including Oracle and IBM. SCA, as used in SOA suite, is designed as a way to crystallise the concepts of SOA into a standard which ensures that SOA principles like the separation of application and business logic are maintained. Orchestration or Integration? A common thing to see with many people who are beginning to either build a new SOA based infrastructure, or move an old system to be service oriented, is confusion in the purpose of SOA technologies like BPEL and enterprise service buses. For a lot of problems, orchestration tools like BPEL or integration tools like an ESB will both do the job and achieve the right objectives; however it’s important to remember that, although a hammer can be used to drive a screw into wood, that doesn’t mean it’s the best way to do it. Service Integration is the act of connecting components together at a low level, which usually results in a single external endpoint for you to expose to your customers or other teams within your organisation – a simple product ordering system, for example, might integrate a stock checking service and a payment processing service. Process Orchestration, however, is generally a higher level approach whereby the (often externally exposed) service endpoints are brought together to track an end-to-end business process. This might include the earlier example of a product ordering service and couple it with a business rules service and human task to handle edge-cases. A good (but not exhaustive) rule-of-thumb is that integrations performed by an ESB will usually be real-time, whereas process orchestration in a SOA composite might comprise processes which take a certain amount of time to complete, or have to wait pending manual intervention. BPEL vs BPMN For some, with pre-existing SOA or business process projects, this decision is effectively already made. For those embarking on new projects it’s certainly an important consideration for those using Oracle SOA software since, due to the components included in SOA Suite and BPM Suite, the choice of which to buy is determined by what they offer. Oracle SOA suite has no BPMN engine, whereas BPM suite has both a BPMN and a BPEL engine. SOA suite has the ESB component “Mediator”, whereas BPM suite has none. Decisions must be made, therefore, on whether just one or both process modelling languages are to be used. The wrong decision could be costly further down the line. Design for performance: Read the complete article here. SOA & BPM Partner Community For regular information on Oracle SOA Suite become a member in the SOA & BPM Partner Community for registration please visit www.oracle.com/goto/emea/soa (OPN account required) If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Facebook Wiki Technorati Tags: C2B2,SOA best practice,SOA Community,Oracle SOA,Oracle BPM,Community,OPN,Jürgen Kress

    Read the article

  • Partition Table and Exadata Hybrid Columnar Compression (EHCC)

    - by Bandari Huang
    Create EHCC table CREATE TABLE ... COMPRESS FOR [QUERY LOW|QUERY HIGH|ARCHIVE LOW|ARCHIVE HIGH]; select owner,table_name,compress_for DBA_TAB_SUBPARTITIONS where compression = ‘ENABLED'; Convert Table/Partition/Subpartition to EHCC Compress Table&Partition&Subpartition to EHCC: ALTER TABLE table_name MOVE COMPRESS FOR [QUERY LOW|QUERY HIGH|ARCHIVE LOW|ARCHIVE HIGH] [PARALLEL <dop>]; ALTER TABLE table_name MOVE PARATITION partition_name COMPRESS FOR [QUERY LOW|QUERY HIGH|ARCHIVE LOW|ARCHIVE HIGH] [PARALLEL <dop>]; ALTER TABLE table_name MOVE SUBPARATITION subpartition_name COMPRESS FOR [QUERY LOW|QUERY HIGH|ARCHIVE LOW|ARCHIVE HIGH] [PARALLEL <dop>]; select owner,table_name,compress_for DBA_TAB_SUBPARTITIONS where compression = ‘ENABLED'; select table_owner,table_name,partition_name,compress_for DBA_TAB_PARTITIONS where compression = ‘ENABLED’; select table_owner,table_name,subpartition_name,compress_for DBA_TAB_SUBPARTITIONS where compression = ‘ENABLED’; Rebuild Unusable Index: select index_name from dba_index where status = 'UNUSABLE'; select index_name,partition_name from dba_ind_partition where status = 'UNUSABLE'; select index_name,subpartition_name from dba_ind_partition where status = 'UNUSABLE'; ALTER INDEX index_name REBUILD [PARALLEL <dop>]; ALTER INDEX index_name REBUILD PARTITION partition_name [PARALLEL <dop>]; ALTER INDEX index_name REBUILD SUBPARTITION subpartition_name [PARALLEL <dop>]; Convert Table/Partition/Subpartition from EHCC to OLTP compression or uncompressed format: Uncompress EHCC Table&Partition&Subpartition: ALTER TABLE table_name MOVE [NOCOMPRESS|COMPRESS for OLTP] [PARALLEL <dop>]; ALTER TABLE table_name MOVE PARTITION partition_name [NOCOMPRESS|COMPRESS for OLTP] [PARALLEL <dop>]; ALTER TABLE table_name MOVE SUBPARTITION subpartition_name [NOCOMPRESS|COMPRESS for OLTP] [PARALLEL <dop>]; select owner,table_name,compress_for DBA_TAB_SUBPARTITIONS where compression = ''; select table_owner,table_name,partition_name,compress_for DBA_TAB_PARTITIONS where compression = ''; select table_owner,table_name,subpartition_name,compress_for DBA_TAB_SUBPARTITIONS where compression = ''; Rebuild Unusable Index: select index_name from dba_index where status = 'UNUSABLE'; select index_name,partition_name from dba_ind_partition where status = 'UNUSABLE'; select index_name,subpartition_name from dba_ind_partition where status = 'UNUSABLE'; ALTER INDEX index_name REBUILD [PARALLEL <dop>]; ALTER INDEX index_name REBUILD PARTITION partition_name [PARALLEL <dop>]; ALTER INDEX index_name REBUILD SUBPARTITION subpartition_name [PARALLEL <dop>];

    Read the article

  • OUM is Flexible and Scalable

    - by user535886
    Flexible and Scalable Traditionally, projects have been focused on satisfying the contents of a requirements document or rigorously conforming to an existing set of work products. Often, especially where iterative and incremental techniques have not been employed, these requirements may be inaccurate, the previous deliverables may be flawed, or the business needs may have changed since the start of the project. Fitness for business purpose, derived from the Dynamic Systems Development Method (DSDM) framework, refers to the focus of delivering necessary functionality within a required timebox. The solution can be more rigorously engineered later, if such an approach is acceptable. Our collective experience shows that applying fit-for-purpose criteria, rather than tight adherence to requirements specifications, results in an information system that more closely meets the needs of the business. In OUM, this principle is extended to refer to the execution of the method processes themselves. Project managers and practitioners are encouraged to scale OUM to be fit-for-purpose for a given situation. It is rarely appropriate to execute every activity within OUM. OUM provides guidance for determining the core set of activities to be executed, the level of detail targeted in those activities and their associated tasks, and the frequency and type of end user deliverables. The project workplan should be developed from this core. The plan should then be scaled up, rather than tailored down, to the level of discipline appropriate to the identified risks and requirements. Even at the task level, models and work products should be completed only to the level of detail required for them to be fit-for-purpose within the current iteration or, at the project level, to suit the business needs of the enterprise and to meet the contractual obligations that govern the project. OUM provides well defined templates for many of its tasks. Use of these templates is optional as determined by the context of the project. Work products can easily be a model in a repository, a prototype, a checklist, a set of application code, or, in situations where a high degree of agility is warranted, simply the tacit knowledge contained in the brain of an analyst or practitioner. For further reading on agility, see Balancing Agility and Discipline: A guide fro the Perplexed.

    Read the article

  • Access Denied on Some Subfolders/Files Within a Share

    - by Tim
    First thing this morning, I find that users on one of our share drives are all getting "access denied". I tried the same drive and also received "access denied" as a Domain Admin. Previous to this, all specified users and admins could get access. I checked share permissions I checked NTFS permissions I temporarily made both types of permissions read/write to "Everyone" -- This worked for one user It turns out that this is occurring for only some files/folders. When I try to manually alter the share of that single share, it can't be shared, access denied. xcacls also gets access denied rebooted the server (not a big deal - this is a smallish company). Does anybody have any insight, my google-fu is coming up blank. Thanks. EDIT: More info, I just ran AccessEnum. There were a lot of "access denied", but I noticed the pattern that all of the access denied had a parent with an owner of "???". When I look at the properties, the "Unable to display owner" message is in the box and I can only make my user account the owner. I can then share the individual file/folder, but it doesn't seem to propogate down to subfolders/files.

    Read the article

  • Play system sounds from one computer through another computer's speakers?

    - by kevinconner
    I have a Mac and a Windows PC at work. I use both at the same time with Synergy and SynergyKM, which is a great setup for me. The Mac has built-in speakers and the PC has a sound card, but no speakers. I don't want to get speakers for use at work; instead I'd rather just have all sounds from both computers play through the Mac's speakers. Is there some sort of audio service I can run on each computer to accomplish that? I would want: System alert sounds, like you configure in the Control Panel Sounds from videos in a web browser, including from Flash

    Read the article

  • How-to get the binding for a tab in the Dynamic Tab Shell Template

    - by Frank Nimphius
    The Dynamic Tab Shell template does expose a method on the Tab.java class that allows you to get access to the ADF binding container for a tab. At least in theory this works, because in practice this call always returns a null value (a bug is filed for this). To work around the problem, you can use code similar to the following to get the ADF binding for a specific tab DCBindingContainer currentBinding = (DCBindingContainer) BindingContext.getCurrent().getCurrentBindingsEntry(); DCBindingContainer templateBinding = (DCBindingContainer)currentBinding.get("ptb1"); DCBindingContainer tabBinding= (DCBindingContainer)templateBinding.get("r"+0);  In the code line above, the tabBinding variable will hold the binding reference to the first tab in the dynamic tab shell template. Note that the tab doesn't need to be visible for this (which has to do with how the template works).  "ptb1" is the template reference name in the PageDef file (Executable section) of the template consumer view. Check this string in your page before using this code. If it differs, change it also in the code above. "r0" is the binding reference of the first tab in the template. Te last tab is referenced by "r14".  

    Read the article

  • Problem with network after malware attack

    - by Cruelio
    Im trying to help some friends with a Win XP machine. I got rid of the malware using Malware Bytes, and HiJackThis. But now they(I) have another problem. When the computer boot into Windows it seems fine. When I start Internet Explorer the browser window opens just fine, but nothing happens for at minute or two. After the two minutes of waiting, the network icon appears in the taskbar next to the clock, and then everything works. The computer is connected to the internet using a Ethernet adapter. I have looked at the Rvent Log and found an error from Perfnet with eventid 2004 <Provider Name="PerfNet" /> <EventID Qualifiers="49152">2004</EventID> <Level>2</Level> <Task>0</Task> <Keywords>0x80000000000000</Keywords> What I have tried so far: In the device manager i have uninstalled the Ethernet adapter and installed it again. I have uninstalled and installed the Windows File and Printer Sharing service. I have verified that both server and workstation services are started. What should I do next?

    Read the article

  • Less Can Be More In E-Commerce

    - by Michael Hylton
    Today’s consumers are inundated with product choices and vendors. Visit your favorite electronics retailer and see the vast assortment of flat panel televisions. Or the variety of detergents at the supermarket. All of this can be daunting for the average consumer who is looking for the products and services that interest them.  In a study titled “Choice is Demotivating: Can One Desire Too Much of a Good Thing”, the author, Sheena Iyengar found that participants actually reported greater subsequent satisfaction with their selections and wrote better essays when their original set of options had been limited. The same can be said for e-commerce and your website. Being able to quickly convert shoppers into buyers with effective merchandising is what makes leading businesses successful. You want to engage each individual visitor with the most-relevant content to drive higher conversions and order values while decreasing abandonment, but predicting what will resonate with each customer is difficult. In a world of choices, online merchandizing tools can help personalize, streamline, and refine what your customers view when they browse your online catalog. The key to being effective is to align your products and content as closely as possible with the customer’s needs. The goal on the home page is to promote your brand and push visitors farther into the site. The home page is often the starting point for repeat customers as well as for new visitors hoping to address their current product needs. As the customer selects different filters and narrows the choices, valuable information is being provided to the retailer about the customer’s current need—regardless of previous search behavior or what other customers with a similar demographic profile have purchased. Together with search pages, category browse pages are among the primary options available to customers as a means of finding products on your site. Once a customer reaches the product detail page, it is clear what that person desires, regardless of the segment the customer falls into. However, don’t disregard campaign-based promotions completely. A campaign targeted to all customers but featuring rule-driven promotions tied to the product can be effective. Click here to learn more about merchandizing techniques so what your customer sees if half full and not half empty.

    Read the article

  • ExaLogic 2.01 Implementations– partner resource kit & training material

    - by JuergenKress
    Are you working on ExaLogic 2.01 Implementations? Let us know, we are happy to support you! Please make sure that you contact us for dedicated technical support. Additional we added new material to the ExaLogic wiki page. Benefits of deploying Oracle e-Business Suite on Exalogic and Exadata.pdf Exalogic-security-1561688.pdf Oracle Exalogic Elastic Cloud Satement of direction.pdf (Oracle and partner confidential) ExaLogic 2.01 Training material For all material, please visit the WebLogic Community Workspace (WebLogic Community membership required). WebLogic Partner Community For regular information become a member in the WebLogic Partner Community please visit: http://www.oracle.com/partners/goto/wls-emea ( OPN account required). If you need support with your account please contact the Oracle Partner Business Center. Blog Twitter LinkedIn Mix Forum Wiki Technorati Tags: ExaLogic,ExaLogic 2.01,ExaLogic kit,ExaLogic trianing,enablement,education,WebLogic,WebLogic Community,Oracle,OPN,Jürgen Kress

    Read the article

  • Temp files created in every folder in Windows Server 2003

    - by i.h4d35
    So we have some folders which are shared over the AD Domain (Windows Server 2003). It was just noticed that in 2 of those folders (which contain only Excel and Word files), whenever a file is opened and closed, the temp file which was opened corresponding to that file still remains. Apparently, this's been going on for the past couple of years (which has led to an insane amount of temp files in each folder/subfolder under those shared folders). These shared folders are under the D:drive and not C: drive. There is only one group (containing 2 users) who access the said folders. I cannot understand if this has to do with the settings/permissions for the User/Group/Individual Client machine. For now, I have manually deleted all the temp files from each folder/subfolder. While this is not critical at the moment, I'd still like to clear this up. Also, it takes an additional fraction of a second to open folders that contains more than 10,000 temp files. Thanks in advance.

    Read the article

  • A Comparison of Store Layouts

    - by David Dorf
    Belus Capital Advisors is an independent stock market research firm that sometimes rolls up its sleeves and walks retail stores.  This month Brian Sozzi walked both Macy's and Sears and snapped pictures along the way.  The results are a good lesson in what to do and what not to do in retail.  The dichotomy between the two brands is stark, and Brian's pictures tell the stories of artistry and neglect.  For example, look at these two pictures: Where do you want to shop for sneakers?  The left picture shows the Finish Line store within Macy's and the right shows empty shelves at Sears.  The pictures really show the importance of assortments, in-stock inventory, and presentation.  Take a look at the two stories, and pay particular attention to the pictures of Sears. 19 Photos that Show the New Magic of Macy’s Sears is Vanishing from our Minds, the Shocking 18 Photos That Show Why

    Read the article

  • Creating ADF Faces Comamnd Button at Runtime

    - by Frank Nimphius
    Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} In ADF Faces, the command button is an instance of RichCommandButton and can be created at runtime. While creating the button is not difficult at all, adding behavior to it requires knowing about how to dynamically create and add an action listener reference. The example code below shows two methods: The first method, handleButtonPress is a public method exposed on a managed bean. public void handleButtonPress(ActionEvent event){   System.out.println("Event handled");   //optional: partially refresh changed components if command   //issued as a partial submit } The second method is called in response to a user interaction or on page load and dynamically creates and adds a command button. When the button is pressed, the managed bean method – the action handler – defined above is called. The action handler is referenced using EL in the created MethodExpression instance. If the managed bean is in viewScope, backingBeanScope or pageFlowsScope, then you need to add these scopes as a prefix to the EL (as you would when configuring the managed bean reference at design time) //Create command button and add it as a child to the parent component that is passed as an //argument to this method private void reateCommandButton(UIComponent parent){   RichCommandButton edit = new RichCommandButton();   //make the request partial   edit.setPartialSubmit(true);   edit.setText("Edit");                             //compose the method expression to invoke the event handler   FacesContext fctx = FacesContext.getCurrentInstance();   Application application = fctx.getApplication();   ExpressionFactory elFactory = application.getExpressionFactory();   ELContext elContext = facesCtx.getELContext();   MethodExpression methodExpressio = null;   //Make sure the EL expression references a valid managed bean method. Ensure   //the bean scope is properly addressed    methodExpression =  elFactory.createMethodExpression(                              elContext,"#{myRequestScopeBean.handleButtonPress}",                             Object.class,new Class[] {ActionEvent.class});   //Create the command buttonaction listener reference   MethodExpressionActionListener al = null;          al= new MethodExpressionActionListener(methodExpression);    edit.addActionListener(al);     //add new command button to parent component and PPR the component for     //the button to show    parent.getChildren().add(edit);    AdfFacesContext adfFacesContext = AdfFacesContext.getCurrentInstance();     adfFacesContext.addPartialTarget(parent);  }

    Read the article

  • The Developers Conference 2012: Presentation about CEP & BAM

    - by Ricardo Ferreira
    This year I had the pleasure again of being one of the speakers in the TDC ("The Developers Conference") event. I have spoken in this event for three years from now. This year, the main theme of the SOA track was EDA ("Event-Driven Architecture") and I decided to delivery a comprehensive presentation about one of my preferred personal subjects: Real-time using Complex Event Processing. The theme of the presentation was "Business Intelligence in Real-time using CEP & BAM" and I would like to share here the presentation that I have done. The material is in Portuguese since was an Brazilian event that happened in São Paulo. Once my presentation has a lot of videos, I decided to share the material as a Youtube video, so you can pause, rewind and play again how many times you want it. I strongly recommend you that before starting watching the video, you change the video quality settings to 1080p in High Definition.

    Read the article

< Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >