Search Results

Search found 12987 results on 520 pages for 'tulsa technology center'.

Page 469/520 | < Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >

• What the hell was THAT?!?

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• Splunk is fantastically expensive: What are the alternatives? [closed]

  - by samsmith

  Possible Duplicate: Alternatives to Splunk? This has been discussed, but it has been several months, so it may be time to revisit it: Earlier discussion RE Splunk alternatives For the record, Splunk rocks. But the pricing is simply beyond what we can consider (When I spoke with Splunk today, the cost for a system to index 5gb/day of data is over $30,000.) That is more than we spend on SQL Server (by a large multiple), more than we spend on a rack of servers (by a multiple), etc. etc. The splunk sales team is correct (that for $30K we get more value and functionality than if we spend the same building our own system), but it doesn't matter. The splunk cost is simply too high (by a multiple). Soooooo, we are looking around! Is anyone out there building a splunk like system? Our basic need: Able to listen for syslog messages on multiple udp ports Able to index the incoming data in an async way Some kind of search engine Some kind of UI An API to the search engine (to embed in our console) We currently need to index 3-5gb/day, but need to be able to scale to 10gb/day or more. We do not need a lot of history (30 days is fine). We use Windows 2008 and 2003 servers. Thanks for your thoughts! UPDATE: We spent two weeks researching commercial and open source options. Our conclusion: Write our own (we are a software company... we know how to write things). We built a great system built on mongodb and .NET that gives us the functions we needed from MongoDB in about one engineering week. We have now completed our implementation. We use two Mongodb servers (master and slave), and are able to log and index any amount of log data (5gb/day, 15gb/day, etc), limited only by disk space. OBSERVATIONS: This space needs a solid solution that is $1000-3000 flat rate. The licensing models used by the commercial firms are based on a "milk the data center ops guys" models. That is their right (of course!), but it leaves a HUGE space open for someone to come in underneath them. My guess is that in another year or two there will be a good open source solution that will be really usable. Thank you all for your input (even if it was self promotion).

  Read the article

• Centos 5.5 [Read-only file system] issue after rebooting

  - by canu johann

  I have a virtual server under centos 5.5 (hosted by a japanese company called sakura ) Since yesterday, connection through ssh couldn't be established. I've contacted support center who told me to restart VS from the control panel. After restarting, I got the message below Connected to domain wwwxxxxxx.sakura.ne.jp Escape character is ^] [ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) @@cat: /proc/self/attr/current: Invalid argument Welcome to CentOS Starting udev: @[ OK ] Setting hostname localhost.localdomain: [ OK ] Setting up Logical Volume Management: No volume groups found [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext4 (1) -- /] fsck.ext4 -a /dev/vda3 / contains a file system with errors, check forced. /: Inodes that were part of a corrupted orphan linked list found. /: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY. (i.e., without -a or -p options) [FAILED] *** An error occurred during the file system check. *** Dropping you to a shell; the system will reboot *** when you leave the shell. *** Warning -- SELinux is active *** Disabling security enforcement for system recovery. *** Run 'setenforce 1' to reenable. /etc/rc.d/rc.sysinit: line 53: /selinux/enforce: Read-only file system Give root password for maintenance (or type Control-D to continue): bash: cannot set terminal process group (-1): Inappropriate ioctl for device bash: no job control in this shell bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system bash: cannot create temp file for here-document: Read-only file system (Repair filesystem) 1 # setenforce 1 setenforce: SELinux is disabled (Repair filesystem) 2 # echo 1 (Repair filesystem) 4 # /etc/init.d/sshd status openssh-daemon is stopped (Repair filesystem) 5 # /etc/init.d/sshd start Starting sshd: NET: Registered protocol family 10 lo: Disabled Privacy Extensions touch: cannot touch `/var/lock/subsys/sshd': Read-only file system (Repair filesystem) 6 # sudo /etc/init.d/sshd start sudo: sorry, you must have a tty to run sudo (Repair filesystem) 7 # I have 4 site in production and I need to restart the server quickly (SSH + HTTPD ,...). Thank you for your time.

  Read the article

• Macintosh computers cannot connect to router unless we re-start the modem and router

  - by dwwilson66

  We have a small office network with DSL and a Netgear WNR-2000 wireless router acting as a DHCP server. There are nine devices connected to the router, wirelessly and wired. Whenever a Mac computer tries to connect, it's unsuccessful until we restart the router. Each of the possible devices that can connect to the network is listed in a table to assign certain IP addresses to certain MAC addresses. I am running WPA-PSK security. I can view the router status and see that the Mac's MAC address is visible to the router, but with a 169.* IP address, even though I'm assigning its MAC address to an IP address within my subnet. All non-Mac devices attached to the network connect properly, and can access the network properly even AFTER the Mac has not successfully connected. The network includes Windows devices, Roku boxes, printers and internet ready TVs. This to me, would point to a DHCP issue with how Mac communicates with my network. One interesting thing to note is that if a Mac connects and is prevented from sleeping, it will stay connected indefinitely; reissuing the security cert from the router works fine. I'm not sure if that's supposed to sever & re-establish a connection with the updated credentials or not, but I do stay connected. If the Mac sleeps and is awakened while the security cert is still valid, it connects fine. If the security certificate expires while the Mac is asleep, we need to restart the router. Restarting the router will ALWAYS assigns the proper IP addresses to the Mac equipment. I have heard anecdotally that Mac doesn't play well with 802.11n; I have not tested any other Wireless protocols. There's a couple issues here: First, I found this on Stack, Mac laptop crashing wireless router, but it's not rally applicable since the router isn't crashing. But, it does give some clues about Mac's accessing the network. I did change my encryption from WEP to WPA-PSK, but after about a week, we're still experiencing the issue. I'm not really sure if there's anything else useful in that question. Second, I'm considering getting a 802.11c router and hooking it up to the wireless N router. the 802.11c router would handle all the Mac traffic, and would be set up as a Mac-only subnet. Everything else would remain as is. However, I'm not sure if this is doable on a technology level...do I need a bridge or is this some way to do this with regular consumer gear?

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Windows cannot find the host name "download.microsoft.com" using DNS

  - by joedotnot

  When trying to download a file found on the Microsoft downloads center that starts with, for example, http://download.microsoft.com/download/6/8/7/(some_GUID)/(some_file_name.ext) i get a timeout with "Internet Explorer cannot display the webpage". More information says: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. Diagnose Connection problems says: Windows cannot find the host name "download.microsoft.com" using DNS Bear with me while i expand on the problem: It all started when i tried to download Windows XP mode for my Windows 7 machine. I went to the virtual PC site, then thru the motions of Windows Genuine Advantage which validated ok, but when it redirects to grab the file just times out with above error. (NB: i also tried with the latest Chrome and Firefox but no use due to the Genuine Advantage stuff, so i decided to stick with IE). I am behind an ADSL2+ modem router connecting via wireless (Win 7 Pro laptop); so i hop over to the desktop connected via ethernet (Vista Business), and same result; begin to think site download.microsoft.com site is down. So i give it a break an read up on EDNS, flushing the cache, hosts file, etc... Try again an hour later on the Win 7 machine, still no go; so i turn off the Win 7 (software) firewall, and lo and behold, i can connect and grab any files from download.microsoft.com; (...nice, so we have a Micro$0ft firewall preventing access to a Micro$0ft website, no wonder my auto-updates kept failing but that's another story). But i still am not happy that the desktop connected via ethernet still cannot get to download.microsoft.com, even though i turned off all firewalls, defenders, anti-virus, etc. What is so special / specific about the url download.microsoft.com, any other site is ok, including www.microsoft.com. Any networking guru know what's REALLY going on, and how can i get the desktop to connect? Ping download.microsoft.com - Ping request could not find host download.microsoft.com. Please check the name and try again. Ping google.com or even www.microsoft.com works gives me an IP address. NB: On the wireless laptop ping download.microsoft.com works, i get xxxx.ms.akamai.net [202.7.177.33].

  Read the article

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• Cisco ASA SSL VPN options?

  - by JonH

  Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

  Read the article

• Why do some games randomly turn my screen a random solid color?

  - by Emlena.PhD

  When playing some games my computer will randomly have an error that I cannot fix without turning it off and back on again. The screen changes to one solid color, which varies (off the top of my head I can remember seeing solid green, magenta, etc..) and the sound blares a single tone. The sound sometimes briefly restores and I can still hear the game sounds and even hear and still be heard by people in my Mumble channel, but the screen doesn't right itself so I'm still blind. What's more is this happens in some games but not in others. While the game is actually running, not while I'm still in the menu. However, it does happen if I'm afk or idle but the game world is still rendering. Games where the error occurs: League of Legends World of Warcraft Trine The Sims 2 Dungeon Defenders Safe games: games where it has never occurred: Tribes: Ascend Star Wars: the Old Republic Battlefield 3 So relatively older games cause the problem while newer games do not? I cannot predict when it will happen, it just seems random. However, if it happens and I try playing the same game further after restart it does appear to occur more frequently after the first time. But if I switch to a safe game it doesn't continue happening. Both of my RAM sticks appear fine, flipped position or either one on their own and games still run, computer still boots. I would think over-heating, but then why not all games? ALso, sometimes it happens immediately after I start playing, within seconds of the 3D world booting up. I'm looking to upgrade very soon so I want to figure out what component or software is fubar and replace/repair it. Any suggestions or recommendations of tools would be helpful. Below is some system information. Dxdiag does not detect any problems. Operating System: Windows 7 Home Premium 64-bit (6.1, Build 7601) Service Pack 1 (7601.win7sp1_gdr.120305-1505) System Manufacturer: Gigabyte Technology Co., Ltd. System Model: EP45-UD3R BIOS: Award Modular BIOS v6.00PG Processor: Intel(R) Core(TM)2 Duo CPU E8500 @ 3.16GHz (2 CPUs), ~3.2GHz Memory: 4096MB RAM DirectX Version: DirectX 11 DxDiag Version: 6.01.7601.17514 64bit Unicode Graphics card name: NVIDIA GeForce GTX 285 Driver Version: 8.17.12.9610 (error has occurred w/several driver versions) Sound: I do not have a sound card, been using motherboard's built in sound)

  Read the article

• How to install missing Sound Drivers in Ubuntu?

  - by Sakamoto Kazuma

  I seem to be missing drivers for my Gateway laptop MA7. I have looked in System-Admin-Hardware Drivers, but it does not show up in there.There are also no devices listed in Sound-Hardware. I'm guessing at this point that I don't have the driver installed. However, I get the following output: admin@machine001:~$ cat /proc/asound/cards 0 [Intel ]: HDA-Intel - HDA Intel HDA Intel at 0xd8240000 irq 22 admin@machine001:~$ And my lspci shows: 00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02) 00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02) 00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2) 00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 02) 00:1f.2 SATA controller: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA AHCI Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 02) 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8038 PCI-E Fast Ethernet Controller (rev 14) 03:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02) 04:09.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 04:09.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 04:09.2 Mass storage controller: Texas Instruments 5-in-1 Multimedia Card Reader (SD/MMC/MS/MS PRO/xD) I have also checked alsamixer, and nothing is muted. No headphones plugged into headphone jack either. So the question now is, how do I get sound to work on my laptop? It doesn't work for any application.

  Read the article

• Hot-swap drive got new name, can I change it on-the-fly?

  - by T.J. Crowder

  One of the HDDs in my server's RAID config failed, so I took it out of the array and had the data center hot-swap it. They've done that, but now the new drive is /dev/sdc rather than /dev/sda. I suspect — correct me if I'm wrong — that if I reboot the server, it will be /dev/sda again, so I'm hesitant to add it back to the array as /dev/sdc because I don't want to lay a trap for myself to fall into on the next reboot. I'd just as soon not reboot the server if I don't need to (if I do need to, well, too bad for me). Is there a way I can change the device name from /dev/sdc to /dev/sda without rebooting? This is on Ubuntu 10.04 LTS. It's an md array ("Linux Software RAID"), where currently one of the devices (there are a couple of them) looks like this ("degraded" because I've removed the old /dev/sda from it): # mdadm --detail /dev/md0 /dev/md0: Version : 00.90.03 Creation Time : Sun Oct 11 21:07:54 2009 Raid Level : raid1 Array Size : 97536 (95.27 MiB 99.88 MB) Used Dev Size : 97536 (95.27 MiB 99.88 MB) Raid Devices : 2 Total Devices : 1 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Thu Jun 30 09:31:16 2011 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 UUID : 496be7a5:ab9177ed:7792c71e:7dc17aa4 Events : 0.112 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed Thanks, Update: Reading through the kernel md documentation, I suspect that if the name changes on reboot, it won't matter. (Good design, that.) Here's why: Boot time autodetection of RAID arrays When md is compiled into the kernel (not as module), partitions of type 0xfd are scanned and automatically assembled into RAID arrays. This autodetection may be suppressed with the kernel parameter "raid=noautodetect". As of kernel 2.6.9, only drives with a type 0 superblock can be autodetected and run at boot time. The kernel parameter "raid=partitionable" (or "raid=part") means that all auto-detected arrays are assembled as partitionable. I do have md compiled into the kernel, so I'm rebuilding the array now and will do the reboot to see what happens. Even if it works, the above doesn't answer the question I actually asked, so unless someone comes along and answers that question in the meantime (I'd be interested, even if it's not necessary for what I'm doing this very moment), I'll just delete the question to keep noise down.

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Operative systems on SD cards

  - by HisDudeness

  I was getting some wild ideas the last days, like putting some operative systems into SD cards rather than on my hard drive. I'll go further into details now and explain what lead me to consider this probably abominable decision. I am on a laptop (that means I have a native SD-card reader) which is currently running a cross-distro setup, with a bunch of Linux systems (placed in dedicated ext4 logical partitions into a huge extended one) regulated by an unique GRUB. Since today, my laptop haven't even seen any Windows system with binoculars. I was thinking about placing all the os part of my setup into a Secure Digital to save all my 500 Gb Hard Drive for documents, music, videos and so on, and being able to just remove the SD and boot my system into another computer too, as well as having the possibility of booting other systems into mine by just plugging in another SD, without having to keep it constantly placed in my PC. Also, in the remote case in the near future I just wanted to boot Windows 8 in it, I read it causes major boot incompatibility issues with other systems by needing a digital signature in order for them to start. By having it in a removable drive, I could just get rid of it when I'm needing him and switch its card with Linux one, and so not having any obstacles to their boot. Now, my questions are: I know unlikely traditional rotating disk drives, integrated circuits ones have a limited lifespan in terms of cluster rewriting. Is it an obstacle to that kind of usage? I mean, some Ultrabooks are using SSD now, is it the same issue, or there are some differences between Solid State Drives and Secure Digitals in that sense? Maybe having them to store system files which are in fixed positions (making the even-usage of cluster technology useless) constantly being re-read and updated and similar things just gets them soon unserviceable, do it? Second question: are all motherboards and BIOSes able to boot from SDs just like they are from USB pen drives (I mean, provided card reader is USB-connected, isn't it)? Or can't bootloaders like GRUB be installed on SDs working? If they can't, is it a solution installing GRUB to MBR and making boot option pointing to SD? Will it work? Are there any other problems to installing OSs on a Secure Digital?

  Read the article

• Batch file to uninstall all Sun Java versions?

  - by Ricket

  I'm setting up a system to keep Java in our office up to date. Everyone has all different versions of Java, many of them old and insecure, and some dating back as far as 1.4. I have a System Center Essentials server which can push out and silently run a .msi file, and I've already tested that it can install the latest Java. But old versions (such as 1.4) aren't removed by the installer, so I need to uninstall them. Everyone is running Windows XP. The neat coincidence is that Sun just got bought by Oracle and Oracle has now changed all the instances of "Sun" to "Oracle" in Java. So, I can conveniently not have to worry about uninstalling the latest Java, because I can just do a search and uninstall all Sun Java programs. I found the following batch script on a forum post which looked promising: @echo off & cls Rem List all Installation subkeys from uninstall key. echo Searching Registry for Java Installs for /f %%I in ('reg query HKLM\SOFTWARE\microsoft\windows\currentversion\uninstall') do echo %%I | find "{" > nul && call :All-Installations %%I echo Search Complete.. goto :EOF :All-Installations Rem Filter out all but the Sun Installations for /f "tokens=2*" %%T in ('reg query %1 /v Publisher 2^> nul') do echo %%U | find "Sun" > nul && call :Sun-Installations %1 goto :EOF :Sun-Installations Rem Filter out all but the Sun-Java Installations. Note the tilda + n, which drops all the subkeys from the path for /f "tokens=2*" %%T in ('reg query %1 /v DisplayName 2^> nul') do echo . Uninstalling - %%U: | find "Java" && call :Sun-Java-Installs %~n1 goto :EOF :Sun-Java-Installs Rem Run Uninstaller for the installation MsiExec.exe /x%1 /qb echo . Uninstall Complete, Resuming Search.. goto :EOF However, when I run the script, I get the following output: Searching Registry for Java Installs 'DEV_24x6' is not recognized as an internal or external command, operable program or batch file. 'SUBSYS_542214F1' is not recognized as an internal or external command, operable program or batch file. And then it appears to hang and I ctrl-c to stop it. Reading through the script, I don't understand everything, but I don't know why it is trying to run pieces of registry keys as programs. What is wrong with the batch script? How can I fix it, so that I can move on to somehow turning it into a MSI and deploying it to everyone to clean up this office? Or alternatively, can you suggest a better solution or existing MSI file to do what I need? I just want to make sure to get all the old versions of Java off of everyone's computers, since I've heard of exploits that cause web pages to load using old versions of Java and I want to avoid those.

  Read the article

• mongodb : Can create new thread on FreeBSD?

  - by user197739

  We experienced some strange thing in our mongodb gridfs platform. The platform actually is a bi Xeon E5 (bi quad core) with 128GB of memory, running on freebsd 9 with a zfs pool dedicated for mongodb. [root@mongofile1 ~]# uname -sr FreeBSD 9.1-RELEASE our /boot/loader.conf vfs.zfs.arc_min="2048M" vfs.zfs.arc_max="7680M" vm.kmem_size_max="16G" vm.kmem_size="12G" vfs.zfs.prefetch_disable="1" kern.ipc.nmbclusters="32768" /etc/sysctl.conf net.inet.tcp.msl=15000 net.inet.tcp.keepidle=300000 kern.ipc.nmbclusters=32768 kern.ipc.maxsockbuf=2097152 kern.ipc.somaxconn=8192 kern.maxfiles=65536 kern.maxfilesperproc=32768 net.inet.tcp.delayed_ack=0 net.inet.tcp.sendspace=65535 net.inet.udp.recvspace=65535 net.inet.udp.maxdgram=57344 net.local.stream.recvspace=65535 net.local.stream.sendspace=65535 we follow the recommendation for the ulimit : [root@mongofile1 ~]# su - mongodb $ ulimit -a cpu time (seconds, -t) unlimited file size (512-blocks, -f) unlimited data seg size (kbytes, -d) 33554432 stack size (kbytes, -s) 524288 core file size (512-blocks, -c) unlimited max memory size (kbytes, -m) unlimited locked memory (kbytes, -l) unlimited max user processes (-u) 5547 open files (-n) 32768 virtual mem size (kbytes, -v) unlimited swap limit (kbytes, -w) unlimited sbsize (bytes, -b) unlimited pseudo-terminals (-p) unlimited This server have a twin (same config exactly) for ReplSet in other data center and we have a virtualized arbiter. Some time, almost 3 days, the process of mongodb exit. The problem begin with: Fri Nov 8 11:27:31.741 [conn774697] end connection 192.168.10.162:47963 (23 connections now open) Fri Nov 8 11:27:31.770 [initandlisten] can't create new thread, closing connection Fri Nov 8 11:27:31.771 [rsHealthPoll] replSet member mongofile2:27017 is now in state DOWN Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.162:47968 #774702 (20 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.161:28522 #774703 (21 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.164:15406 #774704 (22 connections now open) Fri Nov 8 11:27:31.774 [initandlisten] connection accepted from 192.168.10.163:25750 #774705 (23 connections now open) Fri Nov 8 11:27:31.810 [initandlisten] connection accepted from 192.168.10.182:20779 #774706 (24 connections now open) Fri Nov 8 11:27:31.855 [initandlisten] connection accepted from 192.168.10.161:28524 #774707 (25 connections now open) Fri Nov 8 11:27:31.869 [initandlisten] connection accepted from 192.168.10.182:20786 #774708 (26 connections now open) and after many "can create new thread" [root@mongofile1 /usr/mongodb]# tail -n 15000 mongod.log.old |grep "create new thread"|wc 5020 55220 421680 and finish by a magnificent Fri Nov 8 11:30:22.333 [rsMgr] replSet warning caught unexpected exception in electSelf() pure virtual method called Fri Nov 8 11:30:22.333 Got signal: 6 (Abort trap: 6). Fri Nov 8 11:30:22.337 Backtrace: 0x599efc 0x8035cb516 0x599efc <_ZN5mongo10abruptQuitEi+988> at /usr/local/bin/mongod 0x8035cb516 <_pthread_sigmask+918> at /lib/libthr.so.3 Extract of mongodb from top 78126 mongodb 77 20 0 1253G 1449M sbwait 0 0:20 0.00% mongod If I restart the process when it crash, the problem is fixed for almost 3 days. Has anyone seen this before, or know of a fix?

  Read the article

• Mysql innoDB corruption after server crash

  - by Ward Loockx

  Yesterday my server died because an outage in the data center. Today it's back up, but having some problems with mysql. First of all my mysql server was not able to start. For this reason I deleted the files ib_logfile0 and ib_logfile1 in /var/lib/mysql folder (I still have the old failing files). After this my server was able to startup again. But now I see a lot of issues in the mysql log file. Sep 1 09:43:55 * mysqld: 120901 9:43:55 InnoDB: Error: page 70944 log sequence number 8 1483471899 Sep 1 09:43:55 * mysqld: InnoDB: is in the future! Current system log sequence number 5 612394935. Sep 1 09:43:55 * mysqld: InnoDB: Your database may be corrupt or you may have copied the InnoDB Sep 1 09:43:55 * mysqld: InnoDB: tablespace but not the InnoDB log files. See Sep 1 09:43:55 * mysqld: InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html When I check the docs on mysql.com, I found that I need to recover my database with backups. I have a backup but not sure what's the good way on importing it. Or is there a way to recover without having to re-import the database again? So if I'm correct I need to put innodb_force_recovery to 4 in mysql and delete all current data and re-import? Is there a way to do this without having downtime? I also have one slave running. This slave has the current status now: Last_Error: Relay log read failure: Could not parse relay log event entry. The possible reasons are: the master's binary log is corrupted (you can check this by running 'mysqlbinlog' on the binary log), the slave's relay log is corrupted (you can check this by running 'mysqlbinlog' on the relay log), a network problem, or a bug in the master's or slave's MySQL code. If you want to check the master's binary log or slave's relay log, you will be able to know their names by issuing 'SHOW SLAVE STATUS' on this slave. How can I totally reset the slave after the new import on the master has happend? Hopefully we can find a solution without not to much downtime. Thanks!

  Read the article

• Problem with several USB devices on Windows XP. How to diagnose USB device?

  - by Lukasz Baran

  Hello All, Recently I've bought some electronic devices (like e.g. Sony Ebook reader PRS-600 or HP PDA IPaq) which are connected to PC using USB ports. These devices have own batteries and they are recharged using USB. However, I am experiencing a problem with Ebook Reader and the similiar thing happens with my PDA (but in this case it's more rare). Sometimes, I am unable to make it start recharging, when it's connected to USB port. The LCD diode on my Reader lights up and the icon in the system tray appears. They both indicate that the device has been connected. However, the device should start recharching and it should appear on Windows XP as a 'explorable' device (just like pendrive it offers some HDDs). None of these happens:( This problem appears on two PCs - desktop and laptop. Both have Windows XP SP3 installed. And what's interesting and surprising to me is the fact that these devices sometimes work without any problems. I mean, I just plug them in and they work properly. Besides that, there are some computers (I have tested a variety of possible conditions) on which the problem does not appear! I am confused and, on the other hand, determined to find out what is the real cause of such strange behavior. Maybe I'm wrong but I always assumed that I'm using deterministic machines, but the described situation makes me feel like I was dreaming:) And that's why I'm asking you here. Are there any tools that could help me diagnose USB ports? Or maybe anyone knows the solution? I have a lot experience with low level programming (mostly from the times of MS-DOS applications), but I'm not an expert when it comes to WinXP technology. If this was a problem with network connection, I would know what to do - I know how to track network traffic, but with USB ports I feel powerless. I have a feeling that the problem may lie in a way WinXP handles USB devices. Personally, I hate auto-discovery and P'n'P features available in Windows. I know that some of may suggest to move to Linux or other *Nix system. Unfortunately, I have to use WinXP in my professional life, so it's rather impossible. Besides that, I don't consider XP as a total disaster. Any help from you will be appreciated!

  Read the article

• How did what appears to be a virus get on my computer? (explanation of situation enclosed)

  - by Massimo

  My system is Windows XP SP3, updated with the latest patches. The PC is connected to a Cisco 877 ADSL router, which does NAT from the internal network to its single static public IP address. There are no forwarded ports, and the router's management console can only be accessed from the inside. I was doing two things: working on a remote office machine via VPN and browsing some web pages on the Cisco web site. The remote network is absolutely safe (it's a lab network, four virtual servers, no publicly accessible services and no users at all; also, none of what I'm going to describe ever happened there). The Cisco web site... well, I suppose is quite safe, too. Suddenly, something happened. Strange popups appears anywhere; programs claiming they're "antimalware", "antispyware" et so on begins autoinstalling; fake Windows Update and Security Center icons pop up in the system tray. svchost.exe began crashing repeatedly. Then, finally, after some minutes of this... BSOD. And, upon rebooting, BSOD again. Even in safe mode. Ok, that was obviously some virus/trojan/whatever. I had to install a new copy of Windows on another partition to clean things up. I found strange executables, services and DLLs almost anywhere. Amongst the other things, user32.dll and ndis.sys had been replaced. A fake software called "Antimalware Doctor" had been installed. There were services with completely random names or even GUIDs (!), and also ones called "IpSect" and "Darkness". There were executable files without an .exe extension. There were even two boot-class drivers, which I'm quite sure are the ones that finally caused the system to crash. A true massacre. Ok, now the questions: What the hell was that?!? It was something more than a simple virus! How did it manage to attack my computer, as I am behind a firewall and was not doing anything even only potentially harmful on the web at the time?

  Read the article

• I want to virtualize my workstation (Tier 1), Looking for Bare Metal Hypervisor for consumer grade components

  - by Chase Florell

  I find myself in this similar bind at least once a year. The bind whereby I'm either upgrading a motherboard, or an OS hard drive. It drives me crazy to have to reinstall Windows, Visual Studio, all my addins, reconfigure my settings etc... every single time. I have a layout and I like and I want to stick with it. My question is... Is there a Bare Metal Hypervisor on the market that will enable me to virtualize my consumer grade workstation? I really want to avoid Host/Client virtualization. Bare Metal is definitely a better way to go for my needs. Is this a good approach, or am I going to suffer some other undesirable side effects by doing this? Clarification My machine has very limited purposes. My primary use is Visual Studio 2010 Professional where I develop ASP.NET MVC Web Applications. The second piece of software that I use (that's system intensive) is Photoshop CS3. Beyond that, my applications are limited to Outlook, Internet Explorer, Firefox, Opera, Chrome, LinqPad, and various other (small) apps. Beyond this, I'm considering working on a node.js project and might run ubuntu on the same hypervisor if possible. System Specs: Gigabyte Motherboard Intel i7 920 12 GB Ram basic 500GB 7200RPM HDD for OS 4 VelociRaptors in Raid 1/0 for build disk Dual GTS250 (512MB) Graphics cards (non SLI) for quad monitors On a side note I also wouldn't be opposed to an alternative suggestion if the limitations are too great. I could install the ESXi (or Zen Server) on my box, and build a separate "thin client" to RDP into the virtual machine. It appears as though RDP supports dual monitors. Edit (Dec 9, 2011) It's been nearly a year since I first asked this question. Since then, there have been a lot of great strides in Hypervisor technology... AND MokaFive is now released for corporate use. I'd love to dig into this question a little more and find out if there is a solid BareMetal Hypervisor for workstations running consumer grade components (IE: not Dell, HP, Lenovo, Etc).

  Read the article

• Second HDD not seen by Windows 7 on Dell Xps l501x

  - by George

  I have a Dell XPS Laptop (l501x). I have replaced the original Seagate 500GB hard drive with an SSD Intel 320 120GB when I first purchased it a year ago. It's been working great. The laptop is booting in about 23 seconds, so the SSD is great. I have an Acronis image created that I came back to every three months just to keep everything clean. The SSD is partitioned with one logical drive for my data. So, recently I thought since I am not using my optical drive often enough to swap it out with a HDD caddy and add my seagate 500gb hard drive. I ordered the caddy placed the HDD in it and now load Windows. It just hangs on the screen that should show the Windows logo. I have tried everything that I know and searched it online. I have uninstalled the SATA controller AHCI and let Windows install it. Still will not boot into windows. I wanted to mention that the Seagate 500GB drive was the one that came with my laptop before I switched to the Intel SSD. As you know Intel has this application called Intel Rapid Technology which loads once in a while and shows the second hard drive, but then, when I restart it hangs again and Windows will not load. As soon as I remove the HDD Caddy and restart it loads Windows fine. I also formated the Seagate 500GB HDD in NTFS and still Windows will not load. When I go into the BIOS it shows the Fixed SSD and also "Sata ODD 500GB" instead of the optical drive but it will not boot into Windows when the HDD caddy is present. There is nothing wrong with the caddy. I have another laptop (Asus) and I installed the HDD caddy and Windows 7 loads without any glitch. I don't get it. I have also flashed the BIOS because Dell had a new version (A08). I also wanted to add that I refreshed Disk Management and the Device Manager and the second drive does not display. At this point I think it's a Windows issue so before I reinstall Windows 7 Home Premium from scratch I wanted to see if there was anything I was missing. Any advice would be greatly appreciated.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• What Sort of Server Setup Am I Likely to Need? - School A/V streaming

  - by DeathMagus

  My prior experience with servers has generally been limited to home file-sharing servers, low-traffic web-servers, and the like. This leaves me with the technical knowledge of how to set up a system, but little experience in terms of scaling said system. My current project, however, has me as the technical lead in setting up a school for online audio and video streaming. The difficulty I'm running into is that I don't quite have the experience to guess what they'll need, and they don't have the experience to tell me - so I've tried to ask as many pertinent questions about what they want to do with their server, and here's what I found out: About 1000 simultaneous users, and hoping to expand (possibly significantly) Both video and audio streaming, at obviously the highest quality possible Support for both live and playlist-based streaming. Probably only one channel, but as it's an educational opportunity, I imagine letting them have a few more wouldn't hurt. No word on whether they're locked into Windows or whether Linux is acceptable. Approximate budget - $7000. It may actually be about $2k less than this, because of a mishap with another technology firm (they ordered a $7000 DV tape deck for some reason, and now the company wants them to pay a 30% restocking fee). The tentative decisions I've already made: I'm planning on using Icecast 2 for my streaming server, fed by VLC Shoutcast encoding. Since the school already has a DMZ set up, I plan on placing the Icecast server in there, and feeding it through their intranet from a simple workstation computer in their studios. This system isn't in any way mission critical - it's an education tool (they're a media magnet school), so I figure redundancy is not worthwhile to them from a cost:benefit perspective. What I don't know is this: How powerful of a server will I need? What is likely to be my major throttle - bandwidth? How can I mitigate that? Will I need anything special for the encoding workstation other than professional video and audio capture cards and a copy of VLC? Are there any other considerations that I'm simply missing? Thanks a lot for any help - if there's more information you need, let me know and I'll tell you all I can.

  Read the article

• Can Remote Desktop Services be deployed and administered by PowerShell alone, without a Domain in WIndows Server 2012 and 2012 R2?

  - by Warren P

  Windows Server 2008 R2 allowed deployment of Terminal Server (Remote Desktop Services) without a domain, and without any insistence on domains. This was very useful, especially for standalone virtual or cloud deployments of a server that is managed remotely for a remote client who has no need or desire for any ActiveDirectory or Domain features. This has become steadily more and more difficult as Microsoft restricts its technologies further and further in each Windows release. With Windows Server 2012, configuring licensing for Remote Desktop Services, is more difficult when not on a domain, but possible still. With Windows Server 2012 R2 (at least in the preview) the barriers are now severe: The Add/Remove Roles and Features wizard in Windows Server 2012 R2 has a special RDS deployment mode that has a rule that says if you aren't on a domain you can't deploy. It tells you to create or join a domain first. This of course comes in direct conflict with the fact that an Active Directory domain controller should not be the same machine as a terminal server machine. So Microsoft's technology is not such much a Cloud Operating System as a Cluster of Unwanted Nodes, needed to support the one machine I actually WANT to deploy. This is gross, and so I am trying to find a workaround. However if you skip that wizard and just go check the checkboxes in the main Roles/Features wizard, you can deploy the features, but the UI is not there to configure them, and when you go back to the RDS configuration page on the roles wizard, you get a message saying you can not administer your Remote Desktop Services system when you are logged in as a Local-Computer Administrator, because although you have all admin priveleges you could have (in your workgroup based system), the RDS configuration UI will not accept those credentials and let you continue. My question in brief is, can I still somehow, obtain the following end result: I need to allow 10-20 users per system to have an RDS (TS) session. I do not need any of the fancy pants RDS options, unless Microsoft somehow depends on those features being present. I believe I need the "RDS Session Host" as this is the guts of "Terminal Server". Microsoft says it is "full Windows desktop for Remote Desktop Services client. I need to configure licensing so that the Grace Period does not expire leaving my RDS non functional, so this probably means I need a way to configure TS CALs. If all of the above could technically be done with the judicious use of the PowerShell, I am prepared to even consider developing all the PowerShell scripts I would need to do the above. I'm not asking someone to write that for me. What I'm asking is, does anyone know if there is a technical impediment to what I want to do above, other than the deliberate crippling of the 2012 R2 UI for Workgroup users? Would the underlying technologies all still work if I manipulate and control them from a PowerShell script? Obviously a 1 word Yes or No answer isn't that useful to anyone, so the question is really, yes or no, and why? In the case the answer is Yes, then how.

  Read the article

• MS DPM 2007: Testing the Recovery for a Production Domain

  - by NewToDPM

  Hi everybody! MS DPM 2007 is a new technology in my company, and so am I to the product. We have a classic Microsoft domain with two DCs, Exchange 2007 and a couple Web/MS SQL servers. I have deployed DPM one month ago on the domain, and after fixing the various issues I got with the replicas inconsistence and adapting the schedule and retention range to the server storage pool size, I can say the backup system is working correctly (no errors) as of today. However, there is one problem: we did not attempt to restore from the backups yet, which is a big no-no of course. I'm not sure about the way I should handle this, my main concern being Exchange and the System State of the DCs. From my understanding, DPM can only protect AND restore data on a server which is part of the same domain as the backup server. If I restore the System State (containing Active Directory) and the Exchange Storage Groups on a testing server, I am afraid it would completely disturb the domain functioning (for example, having two primary DCs on the domain). I am thinking about building a second DPM server on a testing separate domain which would mirror the replicas and then restore it on testing servers from this new domain. Is it the right way to handle the data recovery testing? How did you do on your domain when you first deployed DPM? I'd be grateful for any link/documentation or advice. Thank you in advance for your help! EDIT: Two options seem possible so far: i. Create another DC/Exchange server in the alternate location; ii. Create a separate domain in the alternate location and setup a trust between this domain and the production one. The option i is certainly the best but implies setting up a secondary Exchange server, with a dedicated public IP address so that if Exchange #1 dies, we can still send emails with Exchange #2. I don't know how complex this can be and would need to discuss it with my colleagues. The option ii would only fit the testing purposes. My only question regarding this is: if my production and DPM servers are part of domain A, and there is a trust between domains A and B, can I restore a domain A content to any domain B server?

  Read the article

< Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >