Search Results

Search found 91599 results on 3664 pages for 'user manual'.

Page 469/3664 | < Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >

  • Silent install FirePro v4900 Driver on Windows Embedded 7 Standard

    - by Birgit_B
    I'm trying to install the Drivers for a FirePro v4900 on a Windows Embedded 7 Standard 64bit OS. I want the system to be as small as possible, so i would rather not install the whole catalyst control center, but only the necessary drivers. Because the installation should be accomplished absolutely unattended, the installation process of the FirePro-Driver should also be done without any user interaction. I see two possible solutions for the Problem: Install only the Drivers: Is it possible to solely install the necessary drivers? How would i achieve that? This solution would be the preferred one, because of the smaller footprint. Silent custom install the provided "FirePro_8.911.3.3_VistaWin7_X32X64_135673.exe" (found at ATI FirePro™ Driver). Is there a way, to do that? Thank you in advance for your support! Update: I managed to accomplish a silent installation. I extracted the contents of the above mention installer-file and ran \$_OUTDIR\Bin64\Setup.exe -Install. (There are some other Parameters, just run Setup.exe /?). But i couldn't achieve to just install the drivers without the Cataclyst Control Center, and it seams the Control Center has some unfulfilled dependencies and so it crashes...

    Read the article

  • VirtualBox problems writing to shared folders (Guest Additions installed)

    - by vincent
    I am trying to setup a shared folder from the host (ubuntu 10.10) to mount on a virtualized CentOS 5.5 with Guest Additions (4.0.0) installed (Guest addition features are working ie. seamless mode etc.). I am able to successfully mount the share with: mount -t vboxsf -o rw,exec,uid=48,gid=48 sf_html /var/www/html/ (uid and guid belong to the apache user/group) the only problem is that once mounted and I try to write/create directories and files I get the following: mkdir: cannot create directory `/var/www/html/test': Protocol error I am using the proprietary version of VirtualBox version 4.0.0 r69151. Has anyone had the same problem and been able to fix it or has any idea how to potentially fix this? Another question, the reason for setting this up is this. Our production servers are on CentOS 5.5 however I am a great fan of Ubuntu and would like to develop on Ubuntu rather than CentOS. However in order to stay as close to the production environment I would like to virtualize CentOS to use a web server and use the shared folder as web root. Anyone know whether this isn't a good idea? Has anyone successfully been able to set this up? Thanks guys, your help is always much appreciated and if you need any more information please let me know.

    Read the article

  • Unable to Access Certain Websites

    - by codejoust
    Through a local network, all computers except one ubuntu machine can access 1. Adobe.com 2. Icann.org 3. Apache.org 4. Example.com. The ubuntu machine returns (in firefox): "Though the site seems valid, the browser was unable to establish a connection." Furthermore, when I traceroute those websites using the ubuntu machine, they all return ubuntu.local, and it ends there: (traceroute to icann.org (192.0.32.7), 30 hops max, 40 byte packets 1 ubuntu.local (192.168.1.105) 3000.791 ms !H 3000.808 ms !H 3000.814 ms !H I've checked the hosts file, and there isn't anything in there, and I have an apache server there so if it was redirected to localhost, I'd probably see the localhost webroot page. Thanks in advance! user@ubuntu:~$ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 The Ubuntu Machine is one of six on the network. I'm using opendns for dns, so I do think that should be a problem.

    Read the article

  • Regular Windows 7 BSOD with Shrew VPN client

    - by Junto
    The Shrew VPN client appears to be a good alternative to the Cisco VPN Client on x64 Windows 7. However, since installing it I've seen fairly regular BSODs. Minidump attached: Microsoft (R) Windows Debugger Version 6.11.0001.404 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Temp\020810-23431-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*d:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16385.amd64fre.win7_rtm.090713-1255 Machine Name: Kernel base = 0xfffff800`0285f000 PsLoadedModuleList = 0xfffff800`02a9ce50 Debug session time: Mon Feb 8 18:08:12.887 2010 (GMT+1) System Uptime: 0 days 7:52:06.120 Loading Kernel Symbols ............................................................... ................................................................ .............. Loading User Symbols Loading unloaded module list .... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck A, {0, 2, 0, fffff800028d50b6} Unable to load image \SystemRoot\system32\DRIVERS\vfilter.sys, Win32 error 0n2 *** WARNING: Unable to verify timestamp for vfilter.sys *** ERROR: Module load completed but symbols could not be loaded for vfilter.sys Probably caused by : vfilter.sys ( vfilter+29a6 ) Followup: MachineOwner Machine is a brand spanking new Dell Precision T5500. Superuser appears to have several recommendations for the Shrew VPN Client as an alternative to the Cisco VPN client on 64 bit machines, so I wondered if anyone here has seen this problem and possibly found a solution to the problem? I've decided to run the VPN client under Windows 7 compatibility mode for the moment (Vista SP2) with administrator privileges to see if it makes a difference. Oddly, the VPN doesn't necessarily need to be connected. I've noticed it when browsing using Google Chrome and Internet Explorer, usually when I open up a new tab. If it carries on I think I'll be forced to shell out the 120 EUR for the NCP Client instead.

    Read the article

  • Apple Mac OS X Mavericks inside Virtual Box

    - by John Sonderson
    I have a few questions regarding Mac OS X and OS virtualization. A. Given all the legal restrictions imposed by Apple on Apple products, I would like to know whether it is legal to install the new and freely downloadable Apple Mac OS X Mavericks inside Oracle Virtual Box. B. What about older OS X versions such as Mountain Lion? C. How many machines can I install it on. What if I don't use the Mac to which the OS is downloaded but only use it on Virtual Box, and prefer to, say, install Linux on the Mac computer so that it doesn't become unusable due to the single user license policy and me running the OS on Windows 7 within Virtual Box? D. I have a PC running Windows 7 but would like to get the OS off a second had Mac I'm planning to purchase for this purpose. How must we proceed to copy the OS to an ISO so that I can install it on Windows 7? I am unfamiliar with Macs and do not know what software to use for the purpose, nor where the OS is downloaded to (as an ISO, .app executable, .gz or .zip file or whatever). If anyone could provide some guidance with the process I would sincerely appreciate it. Thanks.

    Read the article

  • Ubuntu Cannot change permissions on files I own and have RW to.

    - by madmaze
    Hello there, I have a harddrive full of backups which for me is mounted at /media/chronus_ I have been trying to give another user rw permission to this drive. The problem is that I cannot change any permissions on this drive, even if i make a new file it puts sets everything to -rw------- here is an excerpt of what i have tried: madmaze@the-gibson:~$ touch testfile madmaze@the-gibson:~$ ls -l testfile -rw-r--r-- 1 madmaze madmaze 0 2011-01-16 20:11 testfile madmaze@the-gibson:~$ chmod 777 testfile madmaze@the-gibson:~$ ls -l testfile -rwxrwxrwx 1 madmaze madmaze 0 2011-01-16 20:11 testfile madmaze@the-gibson:~$ cd /media/chronos_/Pix/ madmaze@the-gibson:/media/chronos_/Pix$ ls -l total 4100 -rw------- 1 madmaze madmaze 28226 2011-01-16 20:18 avp.jpg -rw------- 1 madmaze madmaze 5764 2011-01-16 20:18 avpsmall.jpg -rw------- 1 madmaze madmaze 98414 2011-01-16 20:18 john.jpg -rw------- 1 madmaze madmaze 98785 2011-01-16 20:18 lisa.jpg -rw------- 1 madmaze madmaze 3954281 2011-01-16 20:18 peter.jpg madmaze@the-gibson:/media/chronos_/Pix$ chmod 777 *.jpg madmaze@the-gibson:/media/chronos_/Pix$ ls -l total 4100 -rw------- 1 madmaze madmaze 28226 2011-01-16 20:18 avp.jpg -rw------- 1 madmaze madmaze 5764 2011-01-16 20:18 avpsmall.jpg -rw------- 1 madmaze madmaze 98414 2011-01-16 20:18 john.jpg -rw------- 1 madmaze madmaze 98785 2011-01-16 20:18 lisa.jpg -rw------- 1 madmaze madmaze 3954281 2011-01-16 20:18 peter.jpg madmaze@the-gibson:/media/chronos_/Pix$ sudo chmod 777 *.jpg madmaze@the-gibson:/media/chronos_/Pix$ ls -l total 4100 -rw------- 1 madmaze madmaze 28226 2011-01-16 20:18 avp.jpg -rw------- 1 madmaze madmaze 5764 2011-01-16 20:18 avpsmall.jpg -rw------- 1 madmaze madmaze 98414 2011-01-16 20:18 john.jpg -rw------- 1 madmaze madmaze 98785 2011-01-16 20:18 lisa.jpg -rw------- 1 madmaze madmaze 3954281 2011-01-16 20:18 peter.jpg madmaze@the-gibson:/media/chronos_/Pix$ touch testfile madmaze@the-gibson:/media/chronos_/Pix$ ls -l testfile -rw------- 1 madmaze madmaze 0 2011-01-16 20:25 testfile madmaze@the-gibson:/media/chronos_/Pix$ chmod 777 testfile madmaze@the-gibson:/media/chronos_/Pix$ ls -l testfile -rw------- 1 madmaze madmaze 0 2011-01-16 20:25 testfile madmaze@the-gibson:/media/chronos_/Pix$ Any Ideas what I could be doing wrongly?

    Read the article

  • Command prompt hangs/freezes/crashes sporadically

    - by Leonard Challis
    I'm finding it very difficult to Google this, I don't seem to be able to find anyone with the same issue and I don't know enough about the Windows operating system to troubleshoot. The machine(s) we are seeing the problem on are Windows 7 (professional) both 64bit and 32bit. The problem is with the command prompt freezing up, seemingly randomly. When it does freeze nothing will bring it back to life (i.e. keypress) and it's nothing to do with Quick Insert mode either. It doesn't seem to be when I run standard commands, such as cd, dir, etc, but when I run different programs from the command line. The annoying thing is that sometimes the prompt will freeze and at other times it won't, using the same program/command in the prompt. To add to the frustration, one of my colleagues who had the same problem seems to not have experienced it for a few days now (we're pretty heavy on the command line). It's not a VPN/RDP thing as suggested in other questions and forum posts, as I've seen this both locally and remotely. I thought it was to do with the return code signifying an error or some error state in the program, i.e.: C:\Users\leonardc>mysql -u lalala ERROR 1045 (28000): Access denied for user 'lalala'@'localhost' (using password: NO) but this isn't always the case either. In fact the above command hasn't crashed the shell before. Elevating the prompt to run as Administrator doesn't seem to have any bearing on the problem either. Disabling my anti-virus doesn't have an effect either. Update: I tried the same commands in PowerShell, but I still get the same problem, it will freeze at random times (more often than not, as with the command prompt, but not always). It's not the same as command prompt in the fact that one might work while the other doesn't, but then the next time I try run the same command in both it will suddenly be different again.

    Read the article

  • "Server Unavailable" and removed permissions on .NET sites after Windows Update [closed]

    - by andrewcameron
    Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

    Read the article

  • Change font size for "Default Paragraph Font" in Word

    - by Richard Gadsden
    I have a document where the built-in style "Default Paragraph Font" has been set to a particular size. It shouldn't have a size - it should be inheriting from the paragraph style (that's the whole point of the style). If I go through the user interface, I can't modify this style (the modify button / dropdown is greyed out) While I can work around this in most places, it creates problems for the Table of Contents in particular, as that is forced to be in this style and it overrides the font size from the styles like TOC 1 (etc). I can set the font size through VBA - ActiveDocument.Styles("Default Paragraph Font").Font.size = 10 sets it to ten point, but I can't work out how to reset it back to inherit. At the moment, my table of contents is set to be all in the same size, but really TOC 1 should be bigger than TOC 2. Does anyone have any suggestions for how to fix this? One approach is to use the organizer to copy over the style from a working document, but ideally I'd like a way to resolve the problem without doing that - especially as that's not an easy approach to automate.

    Read the article

  • PC powers off at random times

    - by Timo Huovinen
    Short Version After experiencing some problems with Mobo batteries my PC started to power off at random times, the power off is instant and sudden and does not restart afterwards, need help figuring out the cause. Facts: Powers off when PC is playing games Powers off when PC is idle Powers off when PC is in safe mode Powers off when PC is in BIOS Powers off when PC is booted through a Windows installation USB Replaced the motherboard battery several times Replaced the 650W PSU with a 750W PSU Replaced the RAM Swapped the RAM between slots Re-applied thermal paste to the CPU Checked if the motherboard touches the case Nothing is overclocked PC Specs PC specs: OS: Windows 7 Ultimate SP1 RAM: klingston 1333MHz 4GB stick CPU: AMD Phenom II x4 955 Mobo: Gigabyte 88GMA-UD2H rev 2.2 Motherboard battery: CR2032 3v HDD: 500GB Seagate ST3500418AS ATA Device Graphics: ATI/AMD Radeon HD 6870 Very Long version Around 10 months ago I built a brand new gaming PC. Around 6 months ago it's time setting in windows started resetting to the year 2010. I swapped the Motherboard battery for a new one of the exact same size and shape and voltage, and the problems disappeared...for around 2 weeks. Then the same problem happened again, time gets reset, I swapped the battery again, and the problem was gone for good and everything was great for about 3 months.. then another problem started happening, the PC started to power off suddenly and without warning at completely random times, sometimes the PC works for and hour, sometimes 5 minutes. So I read on the forums that it might be either the PSU or the motherboard Battery or RAM or HDD or the Graphics card or the CPU or the motherboard or the drivers or a Virus or Grounding issues, or something short circuiting, basically it can be anything... I spent some days researching, and decided to remove the possibility of a virus. I reset the CMOS, cleared all BIOS settings and reinstalled windows 7 after a full format of the HDD, but the random power off kept happening. I then disabled the restart on error option in windows and looked at the event log for error events, but they did not help me figure out the problem. Network list service depends on network location awareness the dependency group failed to start Source Kernel Power Event 41 Task Category 63 Source Disk Event ID 11 Task Category None The driver detected a controller error on device disk I took apart the PC, every little piece, re-applied some expensive thermal paste to the CPU, and double checked that none of the pieces are touching the PC case. The problem was gone, the PC no longer powered off randomly I re-attached the graphics card and all was good for 4 months... then the power off problem appeared again, but was happening at high intervals, the PC would shutdown once in 2 days on average, at random points in time, sometimes when it's idle all day long, sometimes when it's running CRYSIS 2. I checked the CPU temperature, because I know that AMD CPU's have a built in protection mechanism that switches off the PC if the CPU gets too hot, and the Temp was 50C system temp, and 45C CPU after running the PC all day long (I did not do tests to see if there are any temperature spikes, don't know how to do them) Originally the PSU that powered the PC was 650Watts and had one 4 pin cable to power the CPU, I replaced it with a new 750Watts PSU which has two 4 pin cables for the CPU, but the problem remained. I removed the graphics card and let the motherboard use the built in one, but the PC kept suddenly powering off at random times. I took apart the PC completely again, and re-applied thermal paste to the CPU, added lots of insulation, and checked for any type of short-circuit possibility again and again, but the problem remained. The problem was like that for some months. I replaced the Battery a couple of times over the time, changed lots of options in windows, and tried everything I could, but it kept powering off, so I stopped using the PC as much as I used to, just living with the random power offs from time to time, until a couple of days ago, when the power off happens almost immediately after powering on the PC. I replaced the RAM with a brand new one, but that did not help. Took apart the PC again, checked for anything anywhere that might cause it, found some small scratches on the very edge of the motherboard to the left of the PCI express x16 slot. This might cause the problem, I thought, but the scratch looks very superficial, not deep at all, and if the scratch did harm the motherboard, wouldn't it cause it to not start at all? And why did it start to power off a while ago, and then suddenly stop powering off? The scratches could not have vanished??? did chkdsk \d but it powered off when it was at 75% I removed the hard disks, the graphics card, while I fiddled with the BIOS settings, and suddenly the PC shut down while I was looking at the BIOS version. This makes me realize, it is not caused by: HDD, Windows, Drivers or the Graphics card I cleared the CMOS again, updated the BIOS from F5 to F6f beta, but that did not help, it might even seem that the PC powers off even sooner. The shutdown even happened to me while I booted through a windows 7 installation USB and was in the repair console. I removed one of the cables powering the CPU, now only one 4pin cable powers it, and it worked for 30mins after doing that, which makes me think that it's the CPU overheating, and because it gets less power, it overheats slower? The things that I am still considering: CPU overheating (does not seem to overheat, maybe false readings?) Motherboard short circuiting (faulty motherboard?) I desperately need some advice in what is faulty, is it a faulty Motherboard or an overheating CPU? or maybe something else? I have been breaking my head over this problem over a span of 6 months. I'm not sure if this is a good place to ask this question, if it is not, then tell me where I can get some experienced help. More info I have also discovered a mysterious piece that seems to have fallen out of the motherboard i119.photobucket.com/albums/o126/yurikolovsky/strangepiece.jpg What is it? Looks like each time that it powers off the datetime gets reset I also found another forum post tomshardware.co.uk/forum/… except I don't have Integrated PeripheralsUSB Keyboard Function option in BIOS :S Comments summary (asked by Random moderator) Q. tell me, if the computer restarts, is it immediately? Does it take a second and then restarts? Do you see (BSOD) or hear (PSU, short circuit) any suspicious when it happens? After reading trough it, it remains the mainboard that is faulty. – JohannesM A. Immediate power off, all the fans stop instantly, all the light turn off instantly, no sound or anything, and it remains off until I turn it back on. Thanks for the feedback, faulty motherboard is what I fear. Q. Try stress-testing the system with Prime95 and see if errors or shutdowns occur when the CPU is under full load. – speakr A. Prime95 heat stress test peaked CPU heat at 60C after 5mins, it powered off after 30mins of testing in the middle of the test with no errors, Prime95 Heat test or the stress-testing with low RAM usage (small or in-place FFTs) do not report errors while testing for 10-60 mins. The power off does not seem like it is affected by Prime95 at all Makes me wonder if it's a CPU or Motherboard issue at all. Q. I had similar random/intermittent problems with my old board. It gave one of a few different symptoms: keyboard and/or mouse would die and/or the RAM wouldn't work and/or it would shut down. It was in bad shape. One problems was that my old PSU had literally burned the connector on it (browned around the pins), another was that a broken lead inside the layers of the PCB would work sometimes if it happened to be hot or if I bent the board—by jamming a hunk of wood behind it. I managed to keep the board alive for several years, but eventually nothing I did would make it work correctly anymore. – Synetech A. I will try that as the last resort, ok? ;) Q. Have you tried a different power cord, surge protector, outlet (on a different circuit). It's worth a shot just to ensure it's not subpar wiring or a week circuit (dips in power may cause shutdown if the PSU can't pull enough juice from the wall). – Kyle A. yes, I attached the PC to an entirely different outlet on a different circuit and the problem persists. After connecting it to a different outlet after starting the PC it gave me 3 long beeps and 1 short one, then the PC immediately proceeded to boot up normally. Q. Re-check your mainboard manual and all PSU connections to your mainboard to be sure that nothing is missing (e.g. 12V ATX 4-pin/6-pin connector). If you can provoke shutdowns with Prime95, then consider buying new hardware -- a stable system should run Prime95 for 24h without any errors. Prime95 mentions errors in the log when they occur and gives a summary after the stress test was stopped manually (e.g. "0 errors, 0 warnings", if all is fine) – speakr A. Re-checked, there are no more PSU connectors that I can physically connect, except the one ATX 4-pin (there are 2 that power the CPU) that I disconnected on purpose, I have reconnected it but the problem persists. Q. With one PC I had a short curcuit. The power button on the front plate had its cables soldered, but not isolated, and the contacts were very close to the metal case. A heavier touch was enough to cause a shutdown. The PC's vibration could be enough – ott-- A. yes, it seems to switch off with even the lightest touch, I switched on the PC, then pulled out the front panel power cable that connects to the motherboard so the power button does not work anymore, after 5 mins of working like that, with the power button completely disconnected, just sitting idle, the PC powered off again, I don't think it's the power button. Q. I wonder if you dare to operate components without the case, that is remove motherboard, power, disk ( just put the motherboard on a wooden desk). Don't bend the adapters when running like that. – ott-- A. yes, I do dare to do that, but only tomorrow, too tired/late right now.

    Read the article

  • Windows 8.1 - Won't boot (0xc000000f), bcdedit fails

    - by user3014097
    I’m pretty much stuck at this point. So, backstory: Windows was installed on one of the SSDs currently in my tower. I bought a new SSD to install Windows (8.1 64 bit) on. Windows installation went fine, booted up, and formatted the old SSD from within Windows (this seems to have been a mistake, but I didn’t realize that at the time). Despite formatting the old SSD, whenever I tried to boot I was told that there were 2 Windows installations. Apparently, when I formatted the old drive, not all of the partitions were removed. So, I booted up with the repair utility, went into cmd, and deleted the non-primary partitions on the old SSD (there were 2 – think they were system and recovery, although I’m forgetting now). Reboot – computer won’t boot. Getting the 0xc000000f “The boot selection failed because a required device is inaccessible” error. Troubleshooting so far: Automatic repair doesn’t fix anything (I’ve never had luck with it though) If I go to install a new version of Windows, the drives and partitions are all there. The SSD is functioning, I at least know that. I’ve essentially gone through this guide: https://neosmart.net/wiki/recovering-windows-bootloader/ Unfortunately, I’m not getting anywhere. I’m not even entirely sure how to describe the errors I’m getting, so I’ve just included pictures of every step (I can't actually post them though so I just included a photobucket link). http://s319.photobucket.com/user/DGalt11/library/Computer%20Issue Am I completely screwed here (i.e. reformat and reinstall?)? Thanks

    Read the article

  • prevalent, recurring hardrive failure intel macbook from 2006/2007

    - by SimonSalman
    Hi, Long story: My MacBook's hard drive failed one year ago, just a month after its warranty ended or: a year and a month after I bought it. After about ten phone calls to Apple's service, they agreed to extend the warranty for another year, so that I got it replaced free of charge. In the mean time, I got to know that many MacBook users that experience/report hard drive failures. Every reported crash was preceded by a slowdown of system performance, an increased occurrence of the spinning beach ball wait courser, and frequent crashes of applications that used to run very robust until then. It happened (as far as I know) with MacBooks from 2006/2007. All these MacBooks additionally suffer from a recurring wearing down of their "top case". Many heavy users had to replace their HDDs three time since 2006/2007 resulting in an head crash, making it impossible to recover data (diagnosis of recovery specialists) in most but not all cases HDD was Seagate (doesn't necessarily have to be the cause, if majority of the MacBook charge contained Seagate drives) And right now (one year after my first disk crash), these symptoms are cumulating on my system, again ... Short version: prevalent hard drive failure on MacBook charge from 2006/2007 (i.e. 2.16 GHz Intel Core 2 Due) I am looking for any (preferable open source) tool for checking the hard drive condition, especially to detect the known "MacBook problem". So, that I can replace the disk on time. If any Mac user found a solution to prevent the repeated failure of heir hard drive, I would be very glad to get to known it. I really enjoy my old MacBook, but I hate to get interrupted every year by an HDD crash. BTW, the issue is already in discussion for a long time, but there seems to be no solution, so far. Thanks, Simon

    Read the article

  • How to use different scaling for every monitor?

    - by Mikael Koskinen
    One of the new features in Windows 8.1 is the new "Desktop display scaling", which allows user to configure scaling per monitor. I've been trying to get this working in preview but with no success. If I configure the scaling, it always affects all of my monitors. I have two monitors, the main one with a higher resolution and the secondary with "normal" resolution. The secondary monitor is used in portrait mode. I would like to configure the main monitor's scaling as the text is currently too small. Here's how things look at the configuration screen by default: Now if I adjust the scaling, click apply and do relogin, everything is bigger. On both of my monitors. I haven't clicked the "Let me choose one scaling level for all my displays", but still the slider seems to affect both of them. If I check the "Let me choose one scaling level", the UI changes to look similar to what we have in Windows 8: Still the problem persists. The scaling is applied to both of my monitors. So, it doesn't matter if I check the box or not, the scaling is always applied to all the displays. Any idea how I could get this to work in preview? I've read some comments which seem to indicate that this should work in preview, though Paul Thurrott mentioned at his Winsupersite article that he either didn't get this to work.

    Read the article

  • What do I need to consider when buying hardware to meet my needs?

    - by Darth Android
    I'm looking to build a new computer from the ground up. I'm not sure what to look out for and need guidance and help on how to pick the hardware needed to construct my new rig. How do I know what to buy? How do I find out if a given CPU will be enough for a certain game or application that I want to run? How do I find out if a given graphics card will be enough for a certain game or application? What is important when looking at motherboards? How much memory do I need? How do I know how much wattage I need for a power supply? What size case do I need? What relevant standards do I need to read up on and be aware of? PCI, PCIe, SATA, USB 2.0, USB 3.0, etc... What "gotchas" do I need to be on the lookout for? Please keep responses generation-agnostic to ensure they will be helpful to our future users. While Stack Exchange does not permit shopping recommendations, it doesn't provide any general advice to consider when buying hardware. So, instead of just telling those that ask what to buy that it's not allowed, let's tell them how to figure out what they need. This question was Super User Question of the Week #20 Read the June 20, 2011 blog entry for more details or submit your own Question of the Week.

    Read the article

  • How to connect to Oracle DB via ODBC

    - by Mat
    I am attempting to connect to a remote Oracle DB via ODBC. I am totally inexperienced and fail to connect. What I have installed: Oracle 'ODBC Driver for RDB' A program I want to connect from (Altova Mapforce, an ETL) What I do: Under Administrative tools I open the Windows "ODBC Data Source Administrator I click 'Add..' and select the Oracle ODBC Driver The Window 'Oracle RDB Driver Setup' opens. I fill in: Data source name: free choice Description: I leave blank Transport: I choose TCP/IP Server: I input the IP address of the server Service: I leave 'generic' UserID: I enter the user name (that belongs to the password I have) Attach Statement: no idea what do do here?? Upon choosing 'OK', the 'Oracle RDB ODBC Driver Connect' opens and I am prompted the password. I enter the password and the connection fails. Questions Do I need further programs on my computer, e.g. the Oracle client of Instant client? I am never prompted the port of the server - isn't this relevant? I am never prompted SID - isn't this relevant? I connected from SQL developer easily - it prompted only server IP, port, username, password and SID.

    Read the article

  • Looking for an application to record audio and video on a linux "embedded" device

    - by Luke404
    I am working with a linux x86 device with limited CPU resources (as a prototype we just use a pentium-m netbook). We'd like to record video from one V4L2 device (we'll probably end up using just USB Video Class devices like all modern webcams) and one audio stream from an ALSA source. The thing will not have screen and keyboard, and obviously no X11 environment. Goals are: do as little work as possible to cope with little cpu resources - for example I'd like to record video in the native MJPEG I get out of the UVC devices encoding audio to MPEG3 Layer-2 (aka mp2) is ok since it let us save a lot of space (compared to raw pcm samples) and does use little cpu power I don't mind loosing some video frames here and there (UVC devices do that) as long as I can get audio and video streams syncronized not require user input to start the thing (a python script takes care of initialization, startup, shutdown, etc...) be able to open the resulting files for postprocessing without too much effort (ie, if mplayer or vlc can play it, it's fine) So far the only app I found that could be started from command line and record V4L2 video + ALSA audio is mencoder but I'm having some difficulties with it. It should be able to do that but I cannot record audio and video together - just one of the two. And if I use two different processes to record to two different files I have no means to get them in sync (audio is more or less always correct, but video framerate will vary over time and it seems to lack timestamps to correctly play it back to the correct time). Long story short, how do you record an unconverted MJPEG stream (from an UVC device) and an audio stream (from an ALSA device, possibly encoding to any standard format) using a command line tool, to a single file (MPEG or any other container), keeping audio and video in sync?

    Read the article

  • How to forceably unmount stuck network share in Mac OS X?

    - by Kyle Lowry
    Not long ago my Xserve failed (power loss) while an iMac was working with files on a particular network share (called "Work Share"). This volume, "Work Share", is now stuck. It can't be seen in the GUI, you can only detect it using the Terminal. Even after power cycling over the course of several days, ls -a still shows that it's there, but I can't unmount it using any command - not even as root in single user mode. Every time I attempt to unmount that volume, I get the message that the resource is busy (which it can't possibly be since nothing is using it), and error code 4915. The issue is that when I mount the real "Work Share", it internally is renamed to "Work Share-1", which breaks all my links, and several files in the share. If I can't unmount the false "Work Share", then that computer would be unuseable without a reformat, I would imagine - and I don't want it to have to come to that. I've tried everything I can think of - it looks like sudo can't save me now. Any ideas on how to unmount this stuck volume?

    Read the article

  • Setup Version Control on Dreamweaver

    - by John Isaacks
    I have a win computer on the Network called WIN2K8FS1 I have TortoiseSVN on a win computer and when I go to checkout a repository with Tortoise it asks me for the URL of the repository. I put in: file://WIN2K8FS1/Media/SVN_repo And it creates the working copy. I am trying to setup Dreamweaver CS5 to work with subversion. I create a new site and I go to the Version Control tab and it asks for a lot if info. First is Access. I choose Subversion since that is the only option Second is Protocol. Not sure which I need so I go with HTTP? Third is Server Address. I am assuming this is the name of the computer with the repository so I put in \\WIN2K8FS1\ Fourth is Repository Path. I put in /Media/SVN_repo Fifth is Port which I leave default to 80 Then it asks for user name and password. I never set one up for anything so I put in my domain username and password. I click test and it tells me: Server and project are not accessible! I am not sure what I am doing wrong. I am not the server admin but I did create the repository and have access to it via Tortoise. So I am not sure what I am doing wrong in Dreamweaver.

    Read the article

  • Using GUI ftp on Win7 and Vista without additional software

    - by Stephen Jones
    Goal: provide a 'no-software' method for 'less technical' users to access password protect ftp location from Win7 and Vista (existing approach for WinXP works). 'No software' method to mean without installing additional software (e.g. FileZilla, WinSCP) - the solution is supplied to external non-technical users. WinXP (works): Using Windows Explorer, WinXP supports non-technical ftp access by pasting: ftp://username:[email protected] into the address bar. The remote ftp site's files / directory structure becomes available and can be copied to / from easily (in the style of local file copy / paste) by a 'less technical' user. Win7 / Vista (doesn't work): Pasting the same URL into the Windows Explorer on Win7 or Vista causes an error: An error occurred opening that folder on the FTP server. Make sure you have permission to access that folder. Details: The connection with the server was reset. Notes: a) The same username/password/server typed from the (DOS) command line achieves access to the server, but this is a more 'technical' solution than desired. I am looking for a WinXP equivalent solution. b) Under 'Control Panel' / 'Internet options' / 'Advanced' tab - the boxes for 'Enable FTP folder view' and 'Use Passive FTP' are ticked (enabled) c) Adding an inbound firewall rule for local port 20 (TCP) was attempted with no difference in results (i.e. failure)

    Read the article

  • Password Protect XML-RPC

    - by Terence Eden
    I have a service running on a server which I want to access via XML-RPC. I've installed all the necessary bits. Within /etc/apache2/httpd.conf I have the single line SCGIMount /RPC2 127.0.0.1:5000 I can run xmlrpc commands from my server - and any server which connects to /RPC2. What I want to do is password protect the directory to stop unauthorised usage. Within /etc/apache2/httpd.conf I've added <Location /RPC2> AuthName "Private" AuthType Basic AuthBasicProvider file AuthUserFile /home/me/myhtpasswd Require user me </Location> Trying to access /RPC2 brings up the "Authorization Required" box and it accepts my username and password. However, xmlrpc now doesn't work! If I run xmlrpc localhost some_command on my server, I get the error Failed. Call failed. HTTP response code is 401, not 200. (XML-RPC fault code -504) Is there any way I can password protect my /RPC2 directory and have xmlrpc commands work?

    Read the article

  • Office 2007 constantly crashes, logged as Event ID 1000

    - by Nori
    I have a user, who despite my best efforts, is having constant Office 2007 crashes. I've tried deleting their profile and setting it up again, repairing office, uninstalling completely and then reinstalling, and swapping out memory sticks. One event log error I keep getting is the following: (note all the Office errors are event id 1000) Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: EMSMDB32.DLL, version: 12.0.6539.5000, time stamp: 0x4c1246f8 Exception code: 0xc0000005 Fault offset: 0x0005d8e2 Faulting process id: 0xf6c Faulting application start time: 0x01cb6633f33384f3 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\EMSMDB32.DLL Report Id: 0d4a2eab-d231-11df-80a0-4061868f5d10 I also get this: Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: olmapi32.dll, version: 12.0.6538.5000, time stamp: 0x4bfc6ad9 Exception code: 0xc0000005 Fault offset: 0x002357a9 Faulting process id: 0x5e4 Faulting application start time: 0x01cb661f4546aa77 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\olmapi32.dll Report Id: a4a90658-d224-11df-80a0-4061868f5d10 The Excel error is this: Faulting application name: EXCEL.EXE, version: 12.0.6535.5002, time stamp: 0x4bd2a7f1 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdbdf Exception code: 0xe06d7363 Fault offset: 0x0000b727 Faulting process id: 0x14a8 Faulting application start time: 0x01cb61ab7bc0abab Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\EXCEL.EXE Faulting module path: C:\Windows\syswow64\KERNELBASE.dll Report Id: ba0c454b-cd9e-11df-80a0-4061868f5d10 Also have gotten this for PowerPoint: Faulting application name: POWERPNT.EXE, version: 12.0.6500.5000, time stamp: 0x49a68f9d Faulting module name: COMShim.dll, version: 2010.3.325.110, time stamp: 0x4c51e0b1 Exception code: 0x40000015 Fault offset: 0x0001e388 Faulting process id: 0x1480 Faulting application start time: 0x01cb5fe9a0660e81 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\POWERPNT.EXE Faulting module path: C:\Program Files (x86)\FactSet\COMShim.dll Report Id: e03d2a21-cbdc-11df-9bc8-4061868f5d10 (Some of the above lines edited to keep you from scroll horizontally.) Lastly, I get this error several times a day, I don't think it is related but maybe it is: Failed extract of third-party root list from auto update cab at: http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab with error: A required certificate is not within its validity period when verifying against the current system clock or the timestamp in the signed file. Any ideas? This is driving me nuts.

    Read the article

  • Can Safari 5.1 for Mac OS display favicons for bookmarks in the Bookmarks Bar?

    - by Greg R.
    When bookmarking a web site, most contemporary browser will display the site's favicon next to the bookmark, both in the bookmark view and the bookmark toolbar. This is a useful feature. In the bookmark toolbar you can edit the name of the bookmark to be blank, effectively leaving the favicon there as an easily identifiable "button" from which to launch the bookmark. This allows you to make more effective user of the space in the bookmark toolbar. I use this approach effectively in Firefox, Chrome, and IE. For example, here is a portion of my Bookmarks Toolbar from Firefox: However, in Safari, no favicon is ever displayed for bookmarks. In the full bookmark view only a generic globe icon is displayed. In the Bookmark Bar in Safari, no icon at all is displayed. Which means the habit of removing the bookmark name & leaving the favicon is useless. Here's what the same configuration (synced between browsers via Xmarks) looks like in Safari. That blank space is where the favicons should be. The boomark is there -- if you hover over it, the blank space changes color to indicate the presence of a bookmark and a tool tip will with the URL will pop up after about two seconds. However, it's really quite unusable. So. The question: is there an extension, plug-in, or modification of some sort that will enable the display of favicons for bookmarks in Safari (OS X Lion 10.7.3 , Safari version 5.1.3)?

    Read the article

  • Why is SSH finding remote keys for other accounts?

    - by Brian Pontarelli
    This is a strange issue I'm having with SSH from my Macbook Pro to a Linux (Ubuntu 11.10) server. I have a DSA key setup on the remote Linux server under my home directory like this: /home/me/.ssh/authorzied_keys I also have the same DSA key setup for a few other accounts on the machine named "foo" and "bar". I can log into all of the accounts fine without any password. Therefore, the DSA keys are all setup correctly. The strange behavior I'm seeing is when debugging the SSH connection. During the connection, the SSH debug is outputting this: debug2: key: /Users/me/.ssh/id_dsa (0x7f91a1424220) debug2: key: /home/foo/.ssh/id_dsa (0x7f91a1425620) debug2: key: /home/bar/.ssh/id_rsa (0x7f91a1425c60) debug2: key: /Users/me/.ssh/id_rsa (0x0) This is strange for so many reasons, but essentially, why is SSH listing out keys on the server (/home/foo/.ssh/id_dsa and /home/bar/.ssh/id_rsa)? These files don't even exist on the server, so why are they listed? I'm not logging into the "foo" or "bar" accounts, so why is SSH even listing those? On my Macbook Pro, I only have a DSA key, but SSH is listing out an RSA key, what's that all about? Another user on the server doesn't get any of these messages when they log in and they have the exact same setup for their DSA key and the exact same Macbook Pro setup as mine? Does anyone know what these messages are and why SSH is outputting them?

    Read the article

  • Debian - starting UFW (Uncomplicated Firewall) before network interfaces are operational

    - by Tomasz Zielinski
    I want to install UFW on Debian Lenny. Everything looks straightforward except that I don't know where to plug UFW startup script so that it configures iptables before hax0rs can break in. I've reviewed runlevel directories and in /etc/rc0.d, /etc/rc6.d and /etc/rcS.d there are items like these: S35networking -> ../init.d/networking S36ifupdown -> ../init.d/ifupdown Runlevel 0 and 6 are for shutdown and reboot so I guess nothing should be changed there, but runlevel S advertises itself (in README) like something for me: The scripts in this directory whose names begin with an 'S' are executed once when booting the system, even when booting directly into single user mode. The following sequence points are defined at this time: * After the S40 scripts have executed, all local file systems are mounted and networking is available. All device drivers have been initialized. (What bothers me is that both rc0/6.d and rcS.d point to the same networking and ifupdown scripts, but after looking at sources I believe those scripts are smart enough to figure out where to start and where to stop networking.) Now, I think that I should plug my /lib/ufw/ufw-init into /etc/rcS.d, with priority higher that the one of ifupdown and networking, i.e. <= 38 for my /etc/rcS.d. Am I right in this "analysis" ?

    Read the article

  • Getting Apache to serve same directory with different authentication over SSL?

    - by Lasse V. Karlsen
    I have set up VisualSVN server, a Subversion server that internally uses Apache, to serve my subversion repositories. I've managed to integrate WebSVN into it as well, and just now was able to get it to serve my repositories through WebSVN without having to authenticate, ie. no username or password prompt comes up. This is good. However, with this set up there is apparently no way for me to authenticate to WebSVN at all, which means all my private repositories are now invisible as far as WebSVN goes. I noticed there is a "Listen 81" directive in the .conf file, since I'm running the server on port 81 instead of 80, so I was wondering if I could set up a https:// connection to a different port, that did require authentication? The reason I need access to my private repositories is that I have linked my bug tracking system to the subversion repositories, so if I click a link in the bug tracking system, it will take me to diffs for the relevant files in WebSVN, and some products are in private repositories. Here's my Location section for WebSVN: <Location /websvn/> Options FollowSymLinks SVNListParentPath on SVNParentPath "C:/Repositories/" SVNPathAuthz on AuthName "Subversion Repository" AuthType Basic AuthBasicProvider file AuthUserFile "C:/Repositories/htpasswd" AuthzSVNAccessFile "C:/Repositories/authz" Satisfy Any Require valid-user </Location> Is there any way I can set up a separate section for a different port, say 8100, that does not have the Satisfy Any directive there, which is what enable anonymous access. Note that a different sub-directory on the server is acceptable as well, so /websvn_secure/, if I can make a location section for that and effectively serve the same content only without the Satisfy Any directive, that'd be good too.

    Read the article

< Previous Page | 465 466 467 468 469 470 471 472 473 474 475 476  | Next Page >