Search Results

Search found 3466 results on 139 pages for 'firewall traversal'.

Page 47/139 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• L2TP connection fails!

  - by a.toraby

  I've installed l2tp-ipsec-vpn but when I try to connect to the vpn server I get error 500. Here are the logs: Jun 17 12:54:37.449 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:54:38.858 Stopping xl2tpd: xl2tpd. Jun 17 12:54:38.859 xl2tpd[1511]: death_handler: Fatal signal 15 received Jun 17 12:54:38.872 ipsec_setup: Starting Openswan IPsec U2.6.37/K3.2.0-23-generic... Jun 17 12:54:39.027 ipsec__plutorun: Starting Pluto subsystem... Jun 17 12:54:39.033 ipsec__plutorun: adjusting ipsec.d to /etc/ipsec.d Jun 17 12:54:39.037 recvref[30]: Protocol not available Jun 17 12:54:39.038 xl2tpd[2442]: This binary does not support kernel L2TP. Jun 17 12:54:39.038 xl2tpd[2444]: xl2tpd version xl2tpd-1.3.1 started on atp-ThinkPad-SL410 PID:2444 Jun 17 12:54:39.038 xl2tpd[2444]: Written by Mark Spencer, Copyright (C) 1998, Adtran, Inc. Jun 17 12:54:39.038 xl2tpd[2444]: Forked by Scott Balmos and David Stipp, (C) 2001 Jun 17 12:54:39.038 xl2tpd[2444]: Inherited by Jeff McAdams, (C) 2002 Jun 17 12:54:39.039 xl2tpd[2444]: Forked again by Xelerance (www.xelerance.com) (C) 2006 Jun 17 12:54:39.039 xl2tpd[2444]: Listening on IP address 0.0.0.0, port 1701 Jun 17 12:54:39.040 Starting xl2tpd: xl2tpd. Jun 17 12:54:39.062 ipsec__plutorun: 002 added connection description "L2TP" Jun 17 12:55:30.753 104 "L2TP" #1: STATE_MAIN_I1: initiate Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 20s for response Jun 17 12:55:30.754 010 "L2TP" #1: STATE_MAIN_I1: retransmission; will wait 40s for response Jun 17 12:55:30.754 003 "L2TP" #1: ignoring Vendor ID payload [MS NT5 ISAKMPOAKLEY 00000008] Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [RFC 3947] method set to=109 Jun 17 12:55:30.754 003 "L2TP" #1: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 109 Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [FRAGMENTATION] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [MS-Negotiation Discovery Capable] Jun 17 12:55:30.755 003 "L2TP" #1: ignoring Vendor ID payload [IKE CGA version 1] Jun 17 12:55:30.755 106 "L2TP" #1: STATE_MAIN_I2: sent MI2, expecting MR2 Jun 17 12:55:30.755 010 "L2TP" #1: STATE_MAIN_I2: retransmission; will wait 20s for response Jun 17 12:55:30.755 003 "L2TP" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed Jun 17 12:55:30.755 108 "L2TP" #1: STATE_MAIN_I3: sent MI3, expecting MR3 Jun 17 12:55:30.756 004 "L2TP" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_sha group=modp1024} Jun 17 12:55:30.756 117 "L2TP" #2: STATE_QUICK_I1: initiate Jun 17 12:55:30.756 010 "L2TP" #2: STATE_QUICK_I1: retransmission; will wait 20s for response Jun 17 12:55:30.756 003 "L2TP" #2: ignoring informational payload, type IPSEC_RESPONDER_LIFETIME msgid=6b03ff69 Jun 17 12:55:30.756 003 "L2TP" #2: NAT-Traversal: received 2 NAT-OA. ignored because peer is not NATed Jun 17 12:55:30.756 003 "L2TP" #2: our client subnet returned doesn't match my proposal - us:192.168.1.3/32 vs them:109.162.174.235/32 Jun 17 12:55:30.757 003 "L2TP" #2: Allowing questionable proposal anyway [ALLOW_MICROSOFT_BAD_PROPOSAL] Jun 17 12:55:30.757 004 "L2TP" #2: STATE_QUICK_I2: sent QI2, IPsec SA established transport mode {ESP=>0x23af21f8 <0xdb4a87b6 xfrm=AES_128-HMAC_SHA1 NATOA=none NATD=none DPD=none} Jun 17 12:55:31.759 xl2tpd[2444]: Connecting to host x.x.x.x, port 1701 Jun 17 12:55:32.021 xl2tpd[2444]: Connection established to x.x.x.x, 1701. Local: 4720, Remote: 200 (ref=0/0). Jun 17 12:55:32.023 xl2tpd[2444]: Calling on tunnel 4720 Jun 17 12:55:32.454 xl2tpd[2444]: Call established with x.x.x.x, Local: 9667, Remote: 3, Serial: 1 (ref=0/0) Jun 17 12:55:32.456 xl2tpd[2444]: start_pppd: I'm running: Jun 17 12:55:32.456 xl2tpd[2444]: "/usr/sbin/pppd" Jun 17 12:55:32.457 xl2tpd[2444]: "passive" Jun 17 12:55:32.458 xl2tpd[2444]: "nodetach" Jun 17 12:55:32.458 xl2tpd[2444]: ":" Jun 17 12:55:32.459 xl2tpd[2444]: "file" Jun 17 12:55:32.459 xl2tpd[2444]: "/etc/ppp/L2TP.options.xl2tpd" Jun 17 12:55:32.460 xl2tpd[2444]: "ipparam" Jun 17 12:55:32.461 xl2tpd[2444]: "x.x.x.x" Jun 17 12:55:32.462 xl2tpd[2444]: "/dev/pts/1" Jun 17 12:55:32.583 pppd[2711]: Plugin passprompt.so loaded. Jun 17 12:55:32.583 pppd[2711]: pppd 2.4.5 started by root, uid 0 Jun 17 12:55:32.619 pppd[2711]: Using interface ppp0 Jun 17 12:55:32.620 pppd[2711]: Connect: ppp0 <--> /dev/pts/1 Jun 17 12:55:33.693 pppd[2711]: /usr/bin/L2tpIPsecVpn exited with code 0 Jun 17 12:55:34.454 [ERROR 404] Authentication failed: closing connection to 'L2TP' Jun 17 12:55:34.456 pppd[2711]: MS-CHAP authentication failed: E=691 Authentication failure Jun 17 12:55:34.457 pppd[2711]: CHAP authentication failed Jun 17 12:55:34.461 Stopping xl2tpd: xl2tpd. Jun 17 12:55:34.462 xl2tpd[2444]: death_handler: Fatal signal 15 received Jun 17 12:55:34.463 pppd[2711]: Modem hangup Jun 17 12:55:34.463 pppd[2711]: Connection terminated. Jun 17 12:55:34.474 ipsec_setup: Stopping Openswan IPsec... Jun 17 12:55:34.482 pppd[2711]: Exit. Jun 17 12:55:35.587 ipsec_setup: ERROR: Module xfrm4_mode_transport is in use Jun 17 12:55:35.665 ipsec_setup: ERROR: Module esp4 is in use I had this problem by ubuntu 11.10 though I can easily connect to the server from windows. I use ubuntu 12.0 64bit

  Read the article

• yield – Just yet another sexy c# keyword?

  - by George Mamaladze

  yield (see NSDN c# reference) operator came I guess with .NET 2.0 and I my feeling is that it’s not as wide used as it could (or should) be.   I am not going to talk here about necessarity and advantages of using iterator pattern when accessing custom sequences (just google it).   Let’s look at it from the clean code point of view. Let's see if it really helps us to keep our code understandable, reusable and testable.   Let’s say we want to iterate a tree and do something with it’s nodes, for instance calculate a sum of their values. So the most elegant way would be to build a recursive method performing a classic depth traversal returning the sum.           private int CalculateTreeSum(Node top)         {             int sumOfChildNodes = 0;             foreach (Node childNode in top.ChildNodes)             {                 sumOfChildNodes += CalculateTreeSum(childNode);             }             return top.Value + sumOfChildNodes;         }     “Do One Thing” Nevertheless it violates one of the most important rules “Do One Thing”. Our  method CalculateTreeSum does two things at the same time. It travels inside the tree and performs some computation – in this case calculates sum. Doing two things in one method is definitely a bad thing because of several reasons: ·          Understandability: Readability / refactoring ·          Reuseability: when overriding - no chance to override computation without copying iteration code and vice versa. ·          Testability: you are not able to test computation without constructing the tree and you are not able to test correctness of tree iteration.   I want to spend some more words on this last issue. How do you test the method CalculateTreeSum when it contains two in one: computation & iteration? The only chance is to construct a test tree and assert the result of the method call, in our case the sum against our expectation. And if the test fails you do not know wether was the computation algorithm wrong or was that the iteration? At the end to top it all off I tell you: according to Murphy’s Law the iteration will have a bug as well as the calculation. Both bugs in a combination will cause the sum to be accidentally exactly the same you expect and the test will PASS. J   Ok let’s use yield! That’s why it is generally a very good idea not to mix but isolate “things”. Ok let’s use yield!           private int CalculateTreeSumClean(Node top)         {             IEnumerable<Node> treeNodes = GetTreeNodes(top);             return CalculateSum(treeNodes);         }             private int CalculateSum(IEnumerable<Node> nodes)         {             int sumOfNodes = 0;             foreach (Node node in nodes)             {                 sumOfNodes += node.Value;             }             return sumOfNodes;         }           private IEnumerable<Node> GetTreeNodes(Node top)         {             yield return top;             foreach (Node childNode in top.ChildNodes)             {                 foreach (Node currentNode in GetTreeNodes(childNode))                 {                     yield return currentNode;                 }             }         }   Two methods does not know anything about each other. One contains calculation logic another jut the iteration logic. You can relpace the tree iteration algorithm from depth traversal to breath trevaersal or use stack or visitor pattern instead of recursion. This will not influence your calculation logic. And vice versa you can relace the sum with product or do whatever you want with node values, the calculateion algorithm is not aware of beeng working on some tree or graph.  How about not using yield? Now let’s ask the question – what if we do not have yield operator? The brief look at the generated code gives us an answer. The compiler generates a 150 lines long class to implement the iteration logic.       [CompilerGenerated]     private sealed class <GetTreeNodes>d__0 : IEnumerable<Node>, IEnumerable, IEnumerator<Node>, IEnumerator, IDisposable     {         ...        150 Lines of generated code        ...     }   Often we compromise code readability, cleanness, testability, etc. – to reduce number of classes, code lines, keystrokes and mouse clicks. This is the human nature - we are lazy. Knowing and using such a sexy construct like yield, allows us to be lazy, write very few lines of code and at the same time stay clean and do one thing in a method. That's why I generally welcome using staff like that.   Note: The above used recursive depth traversal algorithm is possibly the compact one but not the best one from the performance and memory utilization point of view. It was taken to emphasize on other primary aspects of this post.

  Read the article

• Receiving UDP on different Android phones gives different results

  - by user1868982

  I am willing to create a server and client program on my android mobile devices. The devices communicate with each other on the same wifi network, therefore, some simple scanning mechanism must be implemented - The client phones search for a server phone through some kind of broadcast. What I did: My protocol - the client phone broadcasts a message port p on the wifi, the server listens on port p. when the server gets the broadcast message it sends a message back, therefore discovering itself to the client. My code - I have opened a broadcast socket on my app, it sends a broadcast message. Meanwhile there is a python script on my PC that listens and replies - I use python so that my testing will be easier - Wireshark on the PC and I can see everything. What happens: When I use one of my Galaxy S phones - it works and I get a response. When I use the other Galaxy S phone - it doesn't work. Now this is what I know: The phone that works actually has Nexus ROM on it Ver. 4.1.1 The phone that doesn't work has 2.3.3 regular galaxy ROM The python code says it receives both of the broadcasts sent from both phones, and replies to both of them without raising any exception. So far I was thought the problem may be 1. the older version'd phone. 2. the windows firewall 3. the router firewall So I have opened Wireshark, and Indeed I saw that both phones are sending their broadcasts - it was logged on Wireshark. But the python script only responded to the first one. So this is why 1 & 3 are irrelevant - if the router firewall was blocking my UDP I would have still seen the python server response, same with the older versioned phone. To get rid of 2 i just disabled the windows firewall - still same problem. Does anyone has a clue to why this effect might happen? Thanks!

  Read the article

• 'The RPC server is unavailable' when converting a physical ISA/Forefront TMG machine to virtual (P2V) in SCVMM

  - by Goran B.

  When I try to convert a physical ISA/TMG machine to virtual using SCVMM, i keep getting an error in the Collect machine configuration step ('Scan Now' button): VMM is unable to complete the request. The connection to the agent MACHINE_NAME was lost. Ensure that the computer MACHINE_NAME exists on the network, WMI service and the agent are installed and running and that a firewall is not blocking HTTP and WMI traffic. ID: 3157 Details: The RPC server is unavailable (0x800706BA) Firewall rules allow for RPC traffic from the SCVMM machine to ISA/TMG machine.

  Read the article

• Can't Connect to IIS Ftp Site under Amazon EC2

  - by h3n

  IIS 7.5: Ftp Firewall Suport: Data Ranges 49152-65535 using external Ip of Amazon EC2 static IP Ftp IPv4 Restriction: allow: Amazon EC2 static IP Ftp Authentication: Anonymous: Enabled, Basic: Disabled, IISMgr: Enabled Ftp Authorization: Allow All Users: Read/Write Windows Firewall (Inbound): Open port 21 Open port ranges: 49152-65535 (Outbound) Open port: 20 Amazon EC2 Security Group: Custom TCP Rule: 21 Custom TCP Rule: 49152-65535 It works on Internet Explorer when I typed the address: ftp://localhost on the server but when I entered the Amazon EC2 Static IP (ftp://IPADRESS) it doesnt connect. I cant connect also to FileZilla

  Read the article

• Linux TC / Policy Routing tools

  - by Zoredache

  In addition to a really good firewall Linux has a builtin advanced routing and traffic shaping (lartc). There are many applications (firehol, firestarter, etc) to make the creation of iptables firewall easier, what similar to tools exist to make working with the policy routing and traffic control easy?

  Read the article

• Has anyone got Hamachi 2 working on EC2 Windows instances?

  - by Khash

  I have it running and can see the EC2 instance with a direct tunnel. However, I can't ping the EC2 instance nor can I browse the shared folders. I am sure of the following: - File sharing service is running - Folders are shared I have tried the following: - Turning Windows firewall off - Allowing all TCP and UDP ports and ICMP through Amazon EC2 group policy firewall The instance is a Windows 2008 DataCentre 32-bit.

  Read the article

• Unable to connect to SVN server on VPS : Subversion Configuration Problem

  - by Pritam Barhate

  Hello everybody, I purchased a VPS account (centos-5-x86_64) from Hostgator mainly for the purpose of setting up an online Subversion Server. This is the first time I am managing a VPS and my linux skills are not so great, but I have basic knowledge of the OS and have been using it on and off as desktop from last few years. So after foxing through a few tutorials online, as the first step I logged in using SSH root account provided by Hostgator and tried to run, yum install mod_dav_svn subversion As it turns out my account has Cpanel/WHM and since it some concept of easy apache straight forward procedure of yum install mod_dav_svn subversion won't work. After that I found out how it can be worked out by compiling the source and stuff. But the whole procedure looked long and scary. [I am just a linux nub]. so I decided I would just skip whole apache integration stuff and just access the server using svn:// protocol, anyways that's how I configure svn on our LAN. So I installed subversion using yum install subversion It installed fine. Then I created a folder /svn_repos/testproject and ran svnadmin create /svn_repos/testproject/ No Problems Using vi I changed svnserve.conf and passwd files for the repository and added a user with my name. Anonymous users don't have any access, authenticated users have write access. Then I started svnserve using svnserve -d then in same terminal window svn list svn://localhost/svn_repos/testproject Asks for authentication for realm, provided root password then for svn username and password. Provided both. The command returns nothing but exists properly. Returns nothing is understood I didn't import anything. But if try to access svn remotely using in another terminal: svn list svn://ip.add.of.server/svn_repos/testproject svn: Can't connect to host 'ip.add.of.server': Operation timed out Is what I get. Parallels Power Panel that I got from Hostgator reports that: The firewall is not active now. To activate the firewall, choose one of the firewall operation modes. So if firewall is not running and I can access svn using localhost, why the operation is timing out when I try to access svn from a remote machine? Experienced network admins please help. Thanks in advance. Also please suggest a good book which gives detailed information on configuring Dedicated servers + WHM and CPanel.

  Read the article

• Centos does not open port/s after the rule/s are appended

  - by Charlie Dyason

  So after some battling and struggling with the firewall, i see that I may be doing something or the firewall isnt responding correctly there is has a port filter that is blocking certain ports. by the way, I have combed the internet, posted on forums, done almost everything and now hence the website name "serverfault", is my last resort, I need help What I hoped to achieve is create a pptp server to connect to with windows/linux clients UPDATED @ bottom Okay, here is what I did: I made some changes to my iptables file, giving me endless issues and so I restored the iptables.old file contents of iptables.old: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT after iptables.old restore(back to stock), nmap scan shows: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:54 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 997 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 4.95 seconds if I append rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 13:58 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.77 seconds *notice it allows and opens port 443 but no other ports, and it removes port 113...? removing previous rule and if I append rule: (allow and open port 80 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:01 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.014s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.12 seconds *notice it removes port 443 and allows 80 but is closed without removing previous rule and if I append rule: (allow and open port 1723 incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:05 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 996 filtered ports PORT STATE SERVICE 22/tcp open ssh 80/tcp closed http 113/tcp closed ident 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 5.16 seconds *notice no change in ports opened or closed??? after removing rules: iptables -A INPUT -i eth0 -m tcp -p tcp --dport 80 -j ACCEPT iptables -A INPUT -i eth0 -m tcp -p tcp --dport 1723 -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.015s latency). Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 113/tcp closed ident Nmap done: 1 IP address (1 host up) scanned in 5.15 seconds and returning rule: (to accept all tcp ports incoming to server on interface eth0) iptables -A INPUT -i eth0 -m tcp -j ACCEPT nmap output: nmap [server ip] Starting Nmap 6.00 ( nmap.org ) at 2013-11-01 14:07 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). Not shown: 858 filtered ports, 139 closed ports PORT STATE SERVICE 22/tcp open ssh 443/tcp open https 8008/tcp open http Nmap done: 1 IP address (1 host up) scanned in 3.87 seconds notice the eth0 changes the 999 filtered ports to 858 filtered ports, 139 closed ports QUESTION: why cant I allow and/or open a specific port, eg. I want to allow and open port 443, it doesnt allow it, or even 1723 for pptp, why am I not able to??? sorry for the layout, the editor was give issues (aswell... sigh) UPDATE @Madhatter comment #1 thank you madhatter in my iptables file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT # ----------all rules mentioned in post where added here ONLY!!!---------- -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT if I want to allow and open port 1723 (or edit iptables to allow a pptp connection from remote pc), what changes would I make? (please bear with me, my first time working with servers, etc.) Update MadHatter comment #2 iptables -L -n -v --line-numbers Chain INPUT (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 9 660 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 3 0 0 ACCEPT all -- eth0 * 0.0.0.0/0 0.0.0.0/0 4 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 5 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 6 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 REJECT all -- * * 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT 6 packets, 840 bytes) num pkts bytes target prot opt in out source destination just on a personal note, madhatter, thank you for the support , I really appreciate it! UPDATE MadHatter comment #3 here are the interfaces ifconfig eth0 Link encap:Ethernet HWaddr 00:1D:D8:B7:1F:DC inet addr:[server ip] Bcast:[server ip x.x.x].255 Mask:255.255.255.0 inet6 addr: fe80::21d:d8ff:feb7:1fdc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:36692 errors:0 dropped:0 overruns:0 frame:0 TX packets:4247 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2830372 (2.6 MiB) TX bytes:427976 (417.9 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.8.0.1 P-t-P:10.8.0.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) remote nmap nmap -p 1723 [server ip] Starting Nmap 6.00 ( http://nmap.org ) at 2013-11-01 16:17 SAST Nmap scan report for server.address.net ([server ip]) Host is up (0.017s latency). PORT STATE SERVICE 1723/tcp filtered pptp Nmap done: 1 IP address (1 host up) scanned in 0.51 seconds local nmap nmap -p 1723 localhost Starting Nmap 5.51 ( http://nmap.org ) at 2013-11-01 16:19 SAST Nmap scan report for localhost (127.0.0.1) Host is up (0.000058s latency). Other addresses for localhost (not scanned): 127.0.0.1 PORT STATE SERVICE 1723/tcp open pptp Nmap done: 1 IP address (1 host up) scanned in 0.11 seconds UPDATE MadHatter COMMENT POST #4 I apologize, if there might have been any confusion, i did have the rule appended: (only after 3rd post) iptables -A INPUT -p tcp --dport 1723 -j ACCEPT netstat -apn|grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1142/pptpd There are not VPN's and firewalls between the server and "me" UPDATE MadHatter comment #5 So here is an intersting turn of events: I booted into windows 7, created a vpn connection, went through the verfication username & pword - checking the sstp then checking pptp (went through that very quickly which meeans there is no problem), but on teh verfication of username and pword (before registering pc on network), it got stuck, gave this error Connection failed with error 2147943625 The remote computer refused the network connection netstat -apn | grep -w 1723 before connecting: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd after the error came tried again: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd tcp 0 0 41.185.26.238:1723 41.13.212.47:49607 TIME_WAIT - I do not know what it means but seems like there is progress..., any thoughts???

  Read the article

• Cisco ASA SSL VPN options?

  - by JonH

  Disclaimer: I am not a network admin so I may be wrong here but I thought asking here would help. I'm a developer mainly on the .net framework as well as helping get a mobile intranet app working. Because this app is only allowed to be used on our network I can easily run this app on our wireless network connection within our building. All is fine and dandy but we'd also like to be able to run this mobile app at say a customer plant using VPN software. I thought surely this could be easy as we exclusively use Samsung s4 phones so I thought I'd download Cisco's Samsung any connect software to allow us to VPN...its right on the play store. Sure enough it doesn't work. I mention it to our network admin who says not possible since we have old technology that doesn't support SSL. He mentions we'd have to upgrade all of our hardware, the firewall, etc. to get this to work. We really need VPN on our phones not only for this app but other internal apps, etc. He did mention the following: We can’t upgrade the software on our ASA, because we don’t have enough memory for the new version.  (the asa is very old).  We can’t add more memory, so we would have to get a new firewall, which I have been told I cannot do. In addition he also mentioned: The Samsung AnyConnect client uses SSL to connect.  With the current (old) version of software that our firewall is running, the SSL connections are unreliable.  We need different hardware in order to upgrade our firewall, which we are unable to attain at this time.  This is the same reason that Windows 8 clients are not able to connect. I am curious hence me asking. vpns seem to be fairly simple to setup. What other options do I have aside from making this a public site or web service that consumes this data over the internet as this is a complete no no. What can we do to make this work without that much effort or cost.

  Read the article

• Blade Enclosure, Multiple Blade Servers, Whats the closest approximation to a DMZ?

  - by codeulike

  I appreciate that to get a proper DMZ, one should have a physical separation between the DMZ servers and the LAN servers, with a firewall server in between. But, in a network consisting of a single Blade Enclosure containing two or more Blade servers, whats the closest approximation to a DMZ that could be designed? More details: Virtual servers, mostly Windows, running in a VMWare environment on the Blade servers, and physical firewall box between the Blade enclosure and the internet.

  Read the article

• VMWare Server guest cannot browse web on Win2008 host

  - by LachlanG

  Cannot browse the web from the guest VM. Host Windows 2008 R2 web edition Fresh install default firewall settings unchanged VWare server 2.02 Can ping external sites Can resolve DNS hostnames Can browse web Guest VMware NAT networking Win 2000 server No firewall Can ping external sites Can resolve DNS hostnames "Page cannot be displayed" errors when browsing web Could previously browse web when Guest VM run on Win2003 host

  Read the article

• Looking for network monitoring software for Win7 x64 (similar to the one included with Sunbelt perso

  - by rep_movsd

  I've upgraded from Windows XP to Windows 7 (64bit) and I found that the very convenient Sunbelt Kerio Personal Firewall will not work on this version. I hear the Windows 7 firewall is good enough(even though it never prompts for outbound connections) but Kerio had a nice network monitor feature which showed all applications with inbound and outbound connections and the current speed and bytes transferred for each one. Is there any software out there that can give me similar monitoring as what Kerio does? TCPView is almost as good, but doesnt show transfer statistics.

  Read the article

• IIS 7 Web service access

  - by Aharon Manne

  I am trying to debug a simple web service. I have IIS 7 installed on my development machine (Windows 7), and have installed the web service. I can access it from my development machine, but not from any other machine in the local network.I opened the firewall to HTTP access, and I can access the default website from other machines, so it is not the firewall.What security settings should I look at to try to allow devices on the LAN to access the web service?

  Read the article

• Setting up reverse proxy via an HTTP proxy?

  - by billc.cn

  I have a software that has to call an external web API from inside our firewall. Currently the only way to do this is through the HTTP proxy feature of the firewall; however, the software itself does not support proxy configuration. So I am wondering is it possible to setup a reverse proxy for the API that goes through the HTTP proxy? The server is running WS2003. I can install any software on it.

  Read the article

• LOCAL and RADIUS authentication on ASA

  - by ghp

  Have configured local authentication which was working fine.And today I wanted to implement RADIUS too .. but after I have done, Im unable to login to my firewall user-identity default-domain LOCAL aaa authentication ssh console LOCAL and RADIUS aaa-server RADIUS protocol radius aaa-server RADIUS (inside) host xyzabc Key zzzzzz aaa authentication ssh console RADIUS aaa authentication enable console RADIUS aaa authentication http console RADIUS Can someone help me login to my firewall

  Read the article

• Routing between 2 different subnets on 2 different interfaces in SonicOS

  - by Chris1499

  I'm having a bit of a problem allowing traffic between two of my subnets. Here's the structure I've built. The X0 interface has our windows server on it and it handles DHCP/DNS, etc. X1 has the WAN connection. The Sonicwall is handling DHCP on X2. The X3 interface is connected to a different vlan on the 48 port switch. The Sonicwall is handling DHCP on this network as well. So here's what i want to do. The network on X2 is for our guest wireless; i don't want it to be able to access any of the other networks, just the internet, so i that all blocked in the firewall. No issues there. The X3 network is going to be for programmable controllers, and needs to be able to access the X0 network where our computers are. This is where my problem is. I'm not able to get between the 192.168.2.xxx and the 192.168.1.xxx on interfaces X0 and X3 respectively. I have these rules set up in the firewall. The Lan Primary Subnet is the 192.168.2.0 on X0. So if i'm not mistaken, this will allow traffic between the two through the firewall. Now this is where I'm a little confused. Do i need to use NAT to get the traffic from X0 to go to X3 (and vice versa), or a static route, or both? Currently i have both, though i doubt they're done correctly (also in screenshot). I've tried to ping between the two without luck. Any advice, or if you see what's wrong with my setup, is much appreciated. If you need some more information, let me know. Thanks all! EDIT: So i found that i don't neither either NAT or a static route, that the setting in the firewall is enough. I can now ping from the 192.168.1.xxx network, however i can't access the server on the 192.168.2.xxx network. When i try to access i get "An error occured while reconnecting to Z: to server Microsoft Windows Network: The local device name is already in use. This connection has not been restored. What am i missing?

  Read the article

• Wamp, External IP, Forbidden

  - by uBlankText

  When I am trying to access my server through my IP adress/localhost/127.0.0.1 all of thoes are working fine but when I am trying my external IP I get: Forbidden You don't have permission to access / on this server. I was looking for guide referring to the external but I only found to the localhost, If any one know some guide about fixing this problem referring to the external IP I will be very thankful. Edit: I found 1 guide until now referring to the firewall, The firewall is not the problem.

  Read the article

• Virtualnetwork with virtualbox

  - by vpereira

  I would like to test a firewall solution. For that i would like to create a virtual network, without contact with my network and configure two virtual ethernet cards in my firewall. is that possible? say that my virtual machine has two ethernets? If with virtualbox is not possible, is it possible with any VM solution? To create virtual network and virtual devices in my virtual operational system

  Read the article

• Are Multiple Iterators possible in php?

  - by artvolk

  Good day! I know that C# allows multiple iterators using yield, like described here: http://stackoverflow.com/questions/1754041/is-multiple-iterators-is-possible-in-c In PHP there is and Iterator interface. Is it possible to implement more than one iteration scenario for a class? More details (EDIT): For example I have class TreeNode implementing single tree node. The whole tree can be expressed using only one this class. I want to provide iterators for iterating all direct and indirect children of current node, for example using BreadthFirst or DepthFirst order. I can implement this Iterators as separate classes but doing so I need that tree node should expose it's children collection as public. C# pseudocode: public class TreeNode<T> { ... public IEnumerable<T> DepthFirstEnumerator { get { // Some tree traversal using 'yield return' } } public IEnumerable<T> BreadthFirstEnumerator { get { // Some tree traversal using 'yield return' } } }

  Read the article

• Problem building a complete binary tree of height 'h' in Python

  - by Jack

  Here is my code. The complete binary tree has 2^k nodes at depth k. class Node: def __init__(self, data): # initializes the data members self.left = None self.right = None self.data = data root = Node(data_root) def create_complete_tree(): row = [root] for i in range(h): newrow = [] for node in row: left = Node(data1) right = Node(data2) node.left = left node.right = right newrow.append(left) newrow.append(right) row = copy.deepcopy(newrow) def traverse_tree(node): if node == None: return else: traverse_tree(node.left) print node.data traverse_tree(node.right) create_complete_tree() print 'Node traversal' traverse_tree(root) The tree traversal only gives the data of root and its children. What am I doing wrong?

  Read the article

• How do I add netsh advfirewall context command in Visual Studio 2010 Click Once publishing?

  - by Rivers Edge

  I have a .Net 4.0 Windows application which requires access thru the firewall. I know about the netsh advfirewall firewall command, but I would like very much to have this program allowed at install time (the Click Once deployment). How can I add this command to execute as a post install command, exectuing as Administrator - i.e. The person doing the install does not have to execute the netsh advfirewall command separately or does not have to go to the Firewall and manually add the program in the Allowed list. I cannot find an area in Publish in Visual Studio 2010 to insert a post install command line execution.

  Read the article

• Balanced Search Tree Query, Asymtotic Analysis..

  - by AGeek

  Hi, The situation is as follows:- We have n number and we have print them in sorted order. We have access to balanced dictionary data structure, which supports the operations serach, insert, delete, minimum, maximum each in O(log n) time. We want to retrieve the numbers in sorted order in O(n log n) time using only the insert and in-order traversal. The answer to this is:- Sort() initialize(t) while(not EOF) read(x) insert(x,t); Traverse(t); Now the query is if we read the elements in time "n" and then traverse the elements in "log n"(in-order traversal) time,, then the total time for this algorithm (n+logn)time, according to me.. Please explain the follow up of this algorithm for the time calculation.. How it will sort the list in O(nlogn) time?? Thanks.

  Read the article

• Network programming on java

  - by maks

  I have written a simple network program on java using sockets. Program has a client and a server. When user types a word on client side, server simply return this word to client. On server side I use Serversocket and bind it to port 4444. Why does not firewall block this connection on my server PC? I ask this question because earlier I wrote this program using corba technology, and firewall on my server PC was blocking the connection to this port; when I disabled the firewall the program worked fine.

  Read the article

• OpenSwan IPSec phase #2 complications

  - by XXL

  Phase #1 (IKE) succeeds without any problems (verified at the target host). Phase #2 (IPSec), however, is erroneous at some point (apparently due to misconfiguration on localhost). This should be an IPSec-only connection. I am using OpenSwan on Debian. The error log reads the following (the actual IP-addr. of the remote endpoint has been modified): pluto[30868]: "x" #2: initiating Quick Mode PSK+ENCRYPT+PFS+UP+IKEv2ALLOW+SAREFTRACK {using isakmp#1 msgid:5ece82ee proposal=AES(12)_256-SHA1(2)_160 pfsgroup=OAKLEY_GROUP_DH22} pluto[30868]: "x" #1: ignoring informational payload, type NO_PROPOSAL_CHOSEN msgid=00000000 pluto[30868]: "x" #1: received and ignored informational message pluto[30868]: "x" #1: the peer proposed: 0.0.0.0/0:0/0 - 0.0.0.0/0:0/0 pluto[30868]: "x" #3: responding to Quick Mode proposal {msgid:a4f5a81c} pluto[30868]: "x" #3: us: 192.168.1.76<192.168.1.76[+S=C] pluto[30868]: "x" #3: them: 222.222.222.222<222.222.222.222[+S=C]===10.196.0.0/17 pluto[30868]: "x" #3: transition from state STATE_QUICK_R0 to state STATE_QUICK_R1 pluto[30868]: "x" #3: STATE_QUICK_R1: sent QR1, inbound IPsec SA installed, expecting QI2 pluto[30868]: "x" #1: ignoring informational payload, type NO_PROPOSAL_CHOSEN msgid=00000000 pluto[30868]: "x" #1: received and ignored informational message pluto[30868]: "x" #3: next payload type of ISAKMP Hash Payload has an unknown value: 97 X pluto[30868]: "x" #3: malformed payload in packet pluto[30868]: | payload malformed after IV I am behind NAT and this is all coming from wlan2. Here are the details: default via 192.168.1.254 dev wlan2 proto static 169.254.0.0/16 dev wlan2 scope link metric 1000 192.168.1.0/24 dev wlan2 proto kernel scope link src 192.168.1.76 metric 2 Output of ipsec verify: Checking your system to see if IPsec got installed and started correctly: Version check and ipsec on-path [OK] Linux Openswan U2.6.37/K3.2.0-24-generic (netkey) Checking for IPsec support in kernel [OK] SAref kernel support [N/A] NETKEY: Testing XFRM related proc values [OK] [OK] [OK] Checking that pluto is running [OK] Pluto listening for IKE on udp 500 [OK] Pluto listening for NAT-T on udp 4500 [OK] Two or more interfaces found, checking IP forwarding [OK] Checking NAT and MASQUERADEing [OK] Checking for 'ip' command [OK] Checking /bin/sh is not /bin/dash [WARNING] Checking for 'iptables' command [OK] Opportunistic Encryption Support [DISABLED] This is what happens when I run ipsec auto --up x: 104 "x" #1: STATE_MAIN_I1: initiate 003 "x" #1: received Vendor ID payload [RFC 3947] method set to=109 106 "x" #1: STATE_MAIN_I2: sent MI2, expecting MR2 003 "x" #1: received Vendor ID payload [Cisco-Unity] 003 "x" #1: received Vendor ID payload [Dead Peer Detection] 003 "x" #1: ignoring unknown Vendor ID payload [502099ff84bd4373039074cf56649aad] 003 "x" #1: received Vendor ID payload [XAUTH] 003 "x" #1: NAT-Traversal: Result using RFC 3947 (NAT-Traversal): i am NATed 108 "x" #1: STATE_MAIN_I3: sent MI3, expecting MR3 004 "x" #1: STATE_MAIN_I4: ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=aes_128 prf=oakley_sha group=modp1024} 117 "x" #2: STATE_QUICK_I1: initiate 010 "x" #2: STATE_QUICK_I1: retransmission; will wait 20s for response 010 "x" #2: STATE_QUICK_I1: retransmission; will wait 40s for response 031 "x" #2: max number of retransmissions (2) reached STATE_QUICK_I1. No acceptable response to our first Quick Mode message: perhaps peer likes no proposal 000 "x" #2: starting keying attempt 2 of at most 3, but releasing whack I have enabled NAT traversal in ipsec.conf accordingly. Here are the settings relative to the connection in question: version 2.0 config setup plutoopts="--perpeerlog" plutoopts="--interface=wlan2" dumpdir=/var/run/pluto/ nat_traversal=yes virtual_private=%v4:10.0.0.0/8,%v4:192.168.0.0/16,%v4:172.16.0.0/12 oe=off protostack=netkey conn x authby=secret pfs=yes auto=add phase2alg=aes256-sha1;dh22 keyingtries=3 ikelifetime=8h type=transport left=192.168.1.76 leftsubnet=192.168.1.0/24 leftprotoport=0/0 right=222.222.222.222 rightsubnet=10.196.0.0/17 rightprotoport=0/0 Here are the specs provided by the other end that must be met for Phase #2: encryption algorithm: AES (128 or 256 bit) hash algorithm: SHA local ident1 (addr/mask/prot/port): (10.196.0.0/255.255.128.0/0/0) local ident2 (addr/mask/prot/port): (10.241.0.0/255.255.0.0/0/0) remote ident (addr/mask/prot/port): (x.x.x.x/x.x.x.x/0/0) (internal network or localhost) Security association lifetime: 4608000 kilobytes/3600 seconds PFS: DH group2 So, finally, what might be the cause of the issue that I am experiencing? Thank you.

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >