Search Results

Search found 12932 results on 518 pages for 'front controller'.

Page 47/518 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• Swapping 3Ware Raid Card - Best Procedure

  - by Brian Lee Jackson

  We have a server running an old firmware version and driver (just took this position) on the 3Ware 9650SE Raid Controller... We have been having issues with the server and seemed to have narrowed it down to the Raid Card... I will be replacing the Raid card with the same model of 3Ware 9650SE, however, the card ordered most likely will have newer firmware on it. I managed to backup all the data to a very large drive. My plan is to update the firmware/driver on the current setup (which is still booting) and verify that everything works.. Then throw in the new Raid Card, check the firmware version (not letting it post). And update to newest firmware if needed via Java management utility on the card? Is this the best route? Thanks!

  Read the article

• Installing Domain Controller on Hyper-V Host

  - by MichaelGG

  Given a resource limited setup consisting of 2 host machines (HyperV-01 and HyperV-02), is it OK to put the domain controllers in parent partition, instead of their own VM? The main reason is that if the DCs go into a child partition, starting from cold on both machines could lead to a bit of an issue, as there'd be no DCs around until well after both parents have booted. I'm guessing this might cause undesirable effects. Am I correct to be worried about joining the host systems to a domain that's only on VMs? The biggest drawback I've heard so far is that if AD gets heavily used, its resources could cut into HyperV's. I'm not concerned about that for this deployment. Any other suggestions? (Besides finding a 3rd machine and running AD on it.)

  Read the article

• ZFS SAS/SATA controller recommendations

  - by ewwhite

  I've been working with OpenSolaris and ZFS for 6 months, primarily on a Sun Fire x4540 and standard Dell and HP hardware. One downside to standard Perc and HP Smart Array controllers is that they do not have a true "passthrough" JBOD mode to present individual disks to ZFS. One can configure multiple RAID 0 arrays and get them working in ZFS, but it impacts hotswap capabilities (thus requiring a reboot upon disk failure/replacement). I'm curious as to what SAS/SATA controllers are recommended for home-brewed ZFS JBODs. In addition, how does battery-backed write cache (BBWC) play into the solution?

  Read the article

• Error when running adprep32 /rodcprep, trying to add a 2008 domain controller to a 2003 domain

  - by virtuist

  I'm trying to migrate a Small Business Server 2003 to Server 2008 domain. The problem is when I run the adprep32 /rodcprep command as specified as the final step in Step 3 of this article: http://www.experts-exchange.com/Software/Server_Software/Email_Servers/Exchange/A_2881-Migrate-Small-Business-Server-2003-to-Exchange-2010-and-Windows-2008-R2.html I get an error "Adprep could not contact a replica for partition..." which is described in detail here: http://support.microsoft.com/kb/949257 I've also attached the AdPrep.log file for full details. So when I try to run DCPromo on my new Server 2008 PDC (it's not the PDC yet, but want it to be soon), I get an error saying that /rodcprep hasn't ran so there could be errors if I continue. Anyone ran into this or have any suggestions on how to help? Can Dsmgmt be ran on server 2003 to help solve this? Assuming it's a partition error.

  Read the article

• Can windows domain controller be virtualized?

  - by FerranB

  Just the question on the title. There is any problem? Any experience on this?

  Read the article

• Can I upgrade a Windows 2000 domain to 2008 and demote the 2000 server without clients attached?

  - by techie007

  Hi all, We're planning to replace a Windows 2000 domain controller with a new 2008 DC (new hardware). We've elected to take the route of getting the 2000 domain schema up-to-snuff, join the 2008 server, upgrade it to a DC, and after replication demote the 2000 server (eventually to be taken off-line). The goal being to not have to visit all the workstations, and limited domain down-time. :) We want bring the old server here and do all the backups, Domain prep, migration and role transfers here, and then (hopefully) just plop the new 2008 back in place after it's done, and join the 2000 server back as a member server (so we can then do folder migrations, etc.). Can this server work be done off-site, without the workstations attached? If we do this will anything need to be done to the clients, once the new DC is physically in place, so they contact the new 2008 DC; or will they just 'know' and continue on using the existing domain settings/user profiles, etc.? Thanks in advance! :)

  Read the article

• Migrating an Active Directory domain controller to AWS

  - by Xavier Hutchinson

  I am required to migrate a Active Directory server into AWS with a couple other servers (SQL and IIS) to create a dev and test environment for our network / development. My plan at this time is to simply rebuild the Active Directory server in AWS from scratch - which is quite time consuming indeed! I was wondering if anyone had a recommendation as to a better and more efficient approach of migrating a copy of a physical Active Directory server to the cloud? The server is Windows Server 2012. Thank you!

  Read the article

• "RPC Server is unavailable" on Windows 7 Client with Samba3 making logon impossible

  - by HalloDu

  I am running an Samba 3.4.* Server with LDAP Backend on Ubuntu 10.04 LTS as a PDC for purely Windows 7 Clients (about 50). It worked quite fine for a long time, but now sometimes on some machines (really strange to replicate) I cannot login, because he tells me that there are no logon servers. When I look in the machines eventlog after logging in locally, the only error it shows is: "RPC Server is unavailable". The system was ported quite a while back from another machine running the same software versions to this new one. Are there maybe trust or caching issues between the workstations and the domain controller? The number of machines affecting is steadily increasing and so do you know any reason as to why this problem occurs? Any information on workstation and domain trust would also be welcome (After googleing I did not find anything really enlightening).

  Read the article

• RDP add domain users broken

  - by Robuust

  I have 3 servers, - domain controller with dns services - dhcp/rras - file/random server with files stored on it and nothing special so far. All servers have static IP's All servers are in the same domain (SOFTWARE) RDP is enabled for all 3 servers All servers are Windwos Server 2008 R2 I can connect to the DHCP/RRAS server via RDP I cannot connect to DC and File server When I add RPD users (both are domain admin for testing) to the File server they show up like this: What is happening what I don't see? And additional why don't I even get a login screen for RPD? Thanks in advance.

  Read the article

• Servers at remote sites vs. centralized servers?

  - by Boden

  Looking for some opinions here. We've got three physical locations and site-to-site VPN between all three. Currently we've got Windows domain controllers at each location, with roughly 50 clients at each. The domains are currently separate, and we're looking at integrating the three sites. Email (Exchange) will be located at the primary site, and RPD is already being used at the secondary branches to hit the app servers also located at the primary site. The bulk of the local user load at the other two sites is just file sharing. What would the main benefits and drawbacks be of replacing the local domain controllers with NAS devices, and only keeping the domain controller(s) at the primary site? (assuming upgrades are coming regardless) Under what circumstances would you choose one setup over the other?

  Read the article

• Do most front and rear USB connections deliver the same power and performance?

  - by Bratch

  I was reading this Three Monitors For Every User and there were some comments about rear USB ports being able to deliver more power than front USB ports because they are directly connected to the motherboard and closer to the power supply (by circuit board runs). Even though the front USB ports may have connectors farther from the power supply, and there are cables from the motherboard to the front ports, I think that the difference in power would be negligible (unless the case is over 5 meters long). Anyone know for sure if they are the same or different? Note that I'm not talking about an older case where the front might have been USB 1.1 and the rear USB 2.0. A modern case would have USB 2.0 on all ports. And of course using a powered hub would deliver plenty of power.

  Read the article

• User/Group Policies in Windows 2000 domain controller

  - by Chris

  In Server 2000 active directory, I have 5 groups of users and every user has different policies. The problem is that a different desktop loads for only one specific user no matter what changes I make in administrative templates. If I copy this user profile and paste it into another group with a different name, windows workaround loads as it should, but some policies are not applied. Does anybody know a way to solve this problem instead of creating a new group and user from scratch?

  Read the article

• User/Group Policies in Windows 2000 domain controller

  - by Chris

  In Server 2000 active directory, I have 5 groups of users and every user has different policies. The problem is that a different desktop loads for only one specific user no matter what changes I make in administrative templates. If I copy this user profile and paste it into another group with a different name, windows workaround loads as it should, but some policies are not applied. Does anybody know a way to solve this problem instead of creating a new group and user from scratch?

  Read the article

• Tracking Administrator account for Domain Controller

  - by Param

  Have you ever created a Task Scheduler Event Notification via Email regarding password change or wrong attempt for administrator? Ok Let me Elaborate more.... As we know, that Administrator / domain admin / Enterprise admin is very important. So i want to keep a track of the following event - A) I must received a Email, whenever password is change of the administrator account - with date, time and ip address B) I must received a Email notification, whenever Administrator logs in Successfully or Unsuccessfully with date, time and ip address I am thinking to do the above task with Task Scheduler Event Notification, have you ever done with the same method? Thanks & Regards, Param

  Read the article

• Have two exchange servers to communicate together

  - by Data-Base

  We have Exchange Server 2007 using our domain ddd.com. We created an isolated network with a firewall/gateway and installed a DC and Exchange Server 2010 using a demo/test domain (ddd.loc). We opened all the needed ports in the firewall (10.10.2.88) to the Exchange Server 2010. In our main Domain Controller (10.10.2.3) we defined the domain ddd.loc with IP 10.10.2.88 (firewalls). We also we defined MX records to the same IP (10.10.2.88) We did that so when we send email from my email [email protected] it will go to the Exchange Server 2010. Anyways, all the pings test from to any servers are OK. But we are not able to send or receive emails. Between these Exchange Servers we can not send any email from the 2010 to any email in general (emails are pending). Also, in Exchange 2007 we are getting error #550 5.1.1 RESOLVER.ADR.RecipNotFound; not found ##

  Read the article

• Upgrade no raid server to raid

  - by AZee

  I have just learned that our PDC has a single drive with 2 partitions. I also know that this drive has bad blocks as recorded in the event log. What I would like to do is to convert this to a RAID solution with a nice balance between economy and performance. I will admit that I have only configured servers with RAID from scratch, and have no experience upgrading an existing system into a RAID system. In fact, I'm not sure it is even possible. Since this is the PDC for 350+ workstations downtime is important. I'd like to hear from other System Administators how they would tackle this and their recommendations for all devices. At this time it seems to me that I can replace the existing drive and then restore from backup or install a controller, drives, configure the RAID an basically start from scratch. Thank you for taking your time. ~AZee

  Read the article

• Can I create a DC without a DNS Server?

  - by onik

  So as the title says, I need to promote a standalone Win2008R2 server to a Domain Controller, and I don't a DNS Server (I think), as there will be no clients connected to the domain, it will be only used for Remote Desktop Services. Yes, I know, it's considered bad practice to install other roles on the DC, but in this case, it's necessary. Do I need to install the DNS Server, and if I do, how to make it as transparent as possible? EDIT: Seems that I need to install the DNS Server, so I can I configure it not to mess up my entire domain? For example: The server I need to promote is rdc.mydomain.com, and it has an A entry to it's IP in the current DNS, while other servers under mydomain.com are running Linux and don't need to know anything about this Windows box. The domain uses a third-party DNS and all edits and updates need to be done via a separate web page, our servers don't have write/update access.

  Read the article

• 2012 R2 services will not start after promotion to Domain Controller

  - by Cybersylum

  Having a peculiar issue promoting a Windows 2012 R2 server in a domain at 2003 domain/forest functional level. Built a new 2012 R2 server, added the following software (labtech, appassure, eset A/V, & Teamviewer). It activated and appeared to be working fine. I added the Active Directory Domain Services role, and completed the configuration (Domain/Forest Prep, and DC promotion). All appeared to go well. I rebooted the server, and that's where the peculiar stuff began. I noticed the server indicated it needed activated again; but would not accept the key. I verified the key was good. That's when I noticed the Software Protection service (as well as many other core services - Base Filtering engine, DHCP client, firewall, etc) would not start. The error message for all of them was "Access Denied". I called MS, and they wanted to troubleshoot at a service level. Their fix was to use procmon and identify the resource that needed permissions (registry key, file or folder) and add "everyone" with full control). That got the services to start; but the problem re-appeared after a reboot. Thinking the issue might have been with the anti-virus package during the promotion process, I rebuilt the DCs from scratch and removed the metadata from AD (as I could not demote the machines "rpc server unavailble"). I tried to promote the newly built machines again. The only changes to the brand new machines being critical updates. Again the promotion appeared to work fine; but upon reboot (and a long wait to allow replication to occur) similar problems began to re-appear. I have verified that the schema updates are correct (schema version is 69 - for Windows 2012 R2). I am not finding much about this issue through my own searches, so I thought I would post this to see if anyone else has seen anything similar...

  Read the article

• Wireless controllers vs wireless usb hub

  - by David Jensen

  For my htpc i currently only have a steerin wheel as a controller. This is wired and it looks really bad having extended usb wires from the tv to the table. However im thinking of bying some new Gamepads and now comes the question. Should i buy wireless ones or wired and connect them to a wireless usb hub? Having a wireless hub would let me manage my gamepads easily from the couch. A wireless hub also allows me to connect other things that are not input devices from the couch. However im wondering if wireless usb hubs may not be made for input devices in the way that they may not have 100% uptime and probably some delay. Am i right about this?

  Read the article

• Computer Invisible On Domain

  - by Giawa

  Good afternoon, I'm sorry that this isn't a programming question specifically, but stackoverflow has been great at answering questions in the past, so I thought I'd give it a shot. One of our Linux users attempted to install Cygwin on our Windows Server 2008 Domain Controller. Now it is no longer possible to browse the domain and see all of the computers. For example, \\my_domain_name will just bring up a username/password dialog box (that will not accept any username or password, even the domain administrator) and no computers will ever be listed. However, I can still connect to computers based on their name or IP address. So \\eridanus or \\192.168.1.85 still work to connect to the shared directories of computers on our network. Does anyone know where I can find these settings? and how I can fix this problem? Thanks, Giawa

  Read the article

• Restrict Applications access to Device

  - by Dboy1612

  I have a PC that has the ability to handle running multiple game clients at once (specifically Tera Online). What I'd like to do is assign and/or restrict each clients access to a device (Gamepad) so that the actions from each device only effects the client I specify. After doing some research with Python's PyGame, I can see that a Gamepad essentially works like a Keyboard does by sending global key events to the entire system, and then the application reading those events. Question is, how can I make it not global? ONly have one application read one controller? Any help is appreciated!

  Read the article

• Installing raid controller forces reinstall of Windows Server 2008

  - by Tyler

  So, I've tried two different RAID controllers that have external SATA connections on my Server 2008 machine. I can install the hardware, boot into Windows, install the drivers and reboot again. No problems. However, as soon as I try to use eSATA-connected drives and reboot something happens to the Windows install and I can no longer boot into Windows. I tried repairing from the command line, and the end result is that repair console tells me I have 0 Windows installations (?). I end up having no choice but to reinstall Windows to get back on track. I must be doing something fundamentally wrong here, but I don't know what :(

  Read the article

• Intel 82865G Graphics Controller - making it work in Windows 7

  - by abrams

  RE: Putting this out there in case someone else runs into this issue. The intel chipset is on-board. I discovered the reason for the crappy resolution in windows 7 was that the memory to share with the video card was set to 1MB in the BIOS. I changed this to 8MB (the maximum) and then the PC rebooted I was able to select a higher resolution. link|flag answered Aug 18 '09 at 5:53 Nick Kavadias Nick, Does this give Aero functionalty ?

  Read the article

• Adding Internal DNS server in Host file

  - by Param

  I have added Global DNS server ip address to one of my Desktop ( please see the Network configuration screenshot ). and after that i have added my both domain controller ip address in host file, and it is working fine. ( please see the below screen-shot for your reference ) Can you please guide, what problem can i face if i kept my configuration in this way. but i am wondering, can this setting can create a problem? because the computer will be able to reach corp.abc.com easily, with the help of host file.

  Read the article

• Domain account credentials fails to start scheduled tasks

  - by neoco

  I have 2 Windows 2000 servers in a domain 'DC', which run numerous windows scheduled tasks under the 'DC\Task-User' account. These tasks are and have been running successfully in the past couple of years without any account/password modifications. Yesterday, the tasks went to 'Could not start' status. Myself having an admin account, was able to run these tasks with my credentials. Today, I ran the tasks again under the DC\Task-User account and they seem to be running fine without any issues. This has happened in the past too. I'm not into networking so don't know much about the underlying problem. Has this something to do with a Domain controller account authentication? Any pointers will be great!

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >