Search Results

Search found 14257 results on 571 pages for 'intel atom developer prog'.

Page 47/571 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• What's wrong with my wireless?

  - by dazzle

  I am having issues with my wireless connection. My connection is constantly disconnecting, then attempting to reconnect, reconnecting momentarily, then disconnecting etc. on times scales that range from seconds to minutes. In the meantime, needless to say I'm having significant packet loss. I'm running Ubuntu 14.04 64bit, updated and upgraded to today. Here is my card and driver: delta@sager:~$ lspci -vq | grep -i wireless -B 1 -A 5 04:00.0 Network controller: Intel Corporation Wireless 7260 (rev 73) Subsystem: Intel Corporation Dual Band Wireless-AC 7260 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7d00000 (64-bit, non-prefetchable) [size=8K] Capabilities: Kernel driver in use: iwlwifi Here is my kernel: delta@sager:~$ uname -r 3.13.0-34-generic None of the other machines on my home network are having these issues. Windows Vista is networking without issue for goodness sake ;-) Here is a small clipping from the output of dmesg. As you can see, I am getting a cfg80211 message of some sort over and over again (FYI, I've replaced my MAC address with a series of dashes, so anytime there is a ---------------, that was where the MAC address was: [ 1881.739161] wlan1: authenticate with --------------- [ 1881.741561] wlan1: send auth to --------------- (try 1/3) [ 1881.743440] wlan1: authenticated [ 1881.746027] wlan1: associate with --------------- (try 1/3) [ 1881.749244] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1881.754727] wlan1: associated [ 1881.754827] cfg80211: Calling CRDA for country: US [ 1881.761552] cfg80211: Regulatory domain changed to country: US [ 1881.761559] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1881.761564] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1881.761568] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1881.761571] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761574] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761577] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1881.761580] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1881.761584] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1882.391038] cfg80211: Calling CRDA to update world regulatory domain [ 1882.396254] cfg80211: World regulatory domain updated: [ 1882.396260] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1882.396265] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396268] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396271] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1882.396274] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1882.396277] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.148252] wlan1: authenticate with --------------- [ 1886.150005] wlan1: send auth to --------------- (try 1/3) [ 1886.151807] wlan1: authenticated [ 1886.154847] wlan1: associate with --------------- (try 1/3) [ 1886.158147] wlan1: RX AssocResp from --------------- (capab=0x411 status=0 aid=4) [ 1886.163464] wlan1: associated [ 1886.163520] wlan1: Limiting TX power to 30 (30 - 0) dBm as advertised by --------------- [ 1886.163588] cfg80211: Calling CRDA for country: US [ 1886.170500] cfg80211: Regulatory domain changed to country: US [ 1886.170508] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1886.170513] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm) [ 1886.170517] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm) [ 1886.170520] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170523] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170526] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1886.170529] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm) [ 1886.170533] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm) [ 1887.200197] cfg80211: Calling CRDA to update world regulatory domain [ 1887.203655] cfg80211: World regulatory domain updated: [ 1887.203659] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 1887.203662] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203664] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203666] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 1887.203668] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 1887.203670] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) I've poked around on AskUbuntu, and have not found any adequate solutions; have also found similar threads that were left unanswered. Any advice/experience/threads I might be able to pull on would be greatly appreciated. In your opinion, is this a kernel issue, hardware issue, etc.? Thanks in advance. EDIT: chili, here's the output of iwconfig: delta@sager:~$ iwconfig wlan1 IEEE 802.11abg ESSID:"LANbeforetime" Mode:Managed Frequency:2.412 GHz Access Point: ----------- Bit Rate=48 Mb/s Tx-Power=16 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=44/70 Signal level=-66 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:80 Missed beacon:0 eth0 no wireless extensions. lo no wireless extensions.

  Read the article

• Ubuntu 14.04 : Lost my sound randomly tried a few commands and I think I failed

  - by Marc-Antoine Théberge

  I lost my sound the other day and I tried to delete pulseaudio then reinstall, then I tried to delete it and install alsa, It did not work and I had to reinstall everything; overall bad idea... now I can't have any sound. Should I do a fresh install? I don't know how to boot an usb drive with GRUB... Here's my sysinfo System information report, generated by Sysinfo: 2014-05-28 05:45:58 http://sourceforge.net/projects/gsysinfo SYSTEM INFORMATION Running Ubuntu Linux, the Ubuntu 14.04 (trusty) release. GNOME: 3.8.4 (Ubuntu 2014-03-17) Kernel version: 3.13.0-27-generic (#50-Ubuntu SMP Thu May 15 18:08:16 UTC 2014) GCC: 4.8 (i686-linux-gnu) Xorg: 1.15.1 (16 April 2014 01:40:08PM) (16 April 2014 01:40:08PM) Hostname: mark-laptop Uptime: 0 days 11 h 43 min CPU INFORMATION GenuineIntel, Intel(R) Atom(TM) CPU N270 @ 1.60GHz Number of CPUs: 2 CPU clock currently at 1333.000 MHz with 512 KB cache Numbering: family(6) model(28) stepping(2) Bogomips: 3192.13 Flags: fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx constant_tsc arch_perfmon pebs bts aperfmperf pni dtes64 monitor ds_cpl est tm2 ssse3 xtpr pdcm movbe lahf_lm dtherm MEMORY INFORMATION Total memory: 2007 MB Total swap: 1953 MB STORAGE INFORMATION SCSI device - scsi0 Vendor: ATA Model: ST9160310AS HARDWARE INFORMATION MOTHERBOARD Host bridge Intel Corporation Mobile 945GSE Express Memory Controller Hub (rev 03) Subsystem: ASUSTeK Computer Inc. Device 8340 PCI bridge(s) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 1 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 2 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation NM10/ICH7 Family PCI Express Port 4 (rev 02) (prog-if 00 [Normal decode]) Intel Corporation 82801 Mobile PCI Bridge (rev e2) (prog-if 01 [Subtractive decode]) ISA bridge Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02) Subsystem: ASUSTeK Computer Inc. Device 830f IDE interface Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [IDE mode] (rev 02) (prog-if 80 [Master]) Subsystem: ASUSTeK Computer Inc. Device 830f GRAPHIC CARD VGA controller Intel Corporation Mobile 945GSE Express Integrated Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: ASUSTeK Computer Inc. Device 8340 SOUND CARD Multimedia controller Intel Corporation NM10/ICH7 Family High Definition Audio Controller (rev 02) Subsystem: ASUSTeK Computer Inc. Device 831a NETWORK Ethernet controller Qualcomm Atheros AR8121/AR8113/AR8114 Gigabit or Fast Ethernet (rev b0) Subsystem: ASUSTeK Computer Inc. Device 8324

  Read the article

• Downloads killing internet on my home network

  - by Travis

  I am currently having a problem with my wireless. Whenever I try to download anything it kills the internet for every other application(tabs within the same browser, browsers on other computers on the same network) except the process doing the download. This occurs with everything from downloading updates to iso's. I am not using a torrent. It happens when downloading upgrades, browser downloads, or anything else. This problem does not occur when I use Windows 7 on the same computer and it stops killing the internet for other computers if I turn the download/Ubuntu off. I am using an ASUS G74SX laptop running Ubuntu 12.10 with Gnome 3.6. My wireless card is an Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Thanks!

  Read the article

• Unity GUI pauses/freezes for less than a few seconds

  - by Ahmad Nassri

  I've just got my new Lenovo ThinkPad X220 with Intel HD graphics (I'm not sure what the chip is) and I've installed Natty. Everything works great out of the box, except there are short pauses/freezes in the UI that randomly occur, they last less than 2 seconds, actions are still taking place in the background (like typing) when the UI un-freezes I can see the characters I've typed, the app I've clicked, loaded . I can confirm that this is only happening with the new Natty 3D interface, I've tried 2D and the classic interface and there were no issues. Googling this topic seems challenging as I can't relate the problem in keywords. And I keep getting results relating to full GUI freeze which I don't have. This is troubling since I have Natty 3D running on older machines without any issues . I wonder if anybody else have experienced this or came across this issue before. Thanks.

  Read the article

• Monitor resolution messed up, monitor is unknown.

  - by Kaustubh P

  Is there anyway to reset my monitor? My moitor is using the xorg.conf file. I use 10.04, without any Graphics Card. My monitor is an Acer X193W, with a native resolution of 1440x900. This is my xorg.conf file: Section "Screen" Identifier "Configured Screen Device" Device "Configured Video Device" Monitor "Test" DefaultDepth 16 SubSection "Display" Depth 16 Modes "1440x900_60.00" EndSubSection EndSection #Section "Device" # Identifier "Configured Video Device" # HorizSync # VertRefresh #EndSection I still cant view the native resolution, even when defined in the xorg file. An way I can revert to the default, or delete some files, to make the system detect the monitor again? My last resort is the cvt method, and adding it to the xrandr file. EDIT: I use Intel Drivers. My /proc/fb contains 0 VGA16 VGA

  Read the article

• nvidia GT 525m no screen found

  - by Pavan

  I'm a Dell XPS user with nvidia GT 525M with Optimus. When I installed nvidia I was greeted with blank screen. And the error in nvidia log was "Fatal error : No screen found". So after searching for the solutions I figured that I have to insert "BusID" in xorg.conf file. After rebooting I was again greeted with blank screen with error "Fatal error : screen already occupied". I don't what exactly the problem is. Do I need to blacklist Intel inbuilt graphics to nvidia in my machine or anything else needs to be done? Please guide me.

  Read the article

• /etc/X11/xorg.conf doesn't exist?

  - by BBetances

  I'm trying to get my video card properly setup to handle 3D acceleration. After searching a bit, I've come across a few howtos that tell me I need to edit my xorg.conf file. That file doesn't exist. X.org is installed by default, I'm sure, and I figured this video card would be widely supported. 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) Any ideas on how I can get this to work properly and play Starcraft II? Or any game for that matter? No resolution problems or anything, just no 3D rendering.

  Read the article

• Mouse scroll issue after kernel build

  - by Anish S Kumar

  I have a Intel Cedar Trail netbook. For graphics to work, i had to build kernel 3.1 with the drivers. I followed the steps in this document After doing that, now my graphics is fine, but my mouse scroll does not work. Is that because I have not build the kernel properly? Have i missed selecting some options in the kernel compile menu? It will be nice if someone can help me. Also my wacom bamboo tablet is not recognized, i have installed the xserver-xorg-input-wacom drivers.

  Read the article

• Few problems on Dell xps 15 L502 (screen brightness ,blutooth,wi-fi power management problems)

  - by Web-E

  I am running ubuntu 11.10 32bit in my dell xps L502. Working good except few problems. Blue tooth always turned on reboot,I would like to turn it off always. Screen brightness is not saved.Every time I reboot, the screen goes back to full brightness.How to save that? and the most important problem is internet speed through wi-fi is really very slow when operating on battery.the card is intel centrino Advanced-N 1030 with integrated blue tooth. Any help will be appriciated... :)

  Read the article

• How to make "xrandr" work with GMA500?

  - by Nwbie

  Is it error at driver of graphic chip or Xorg or kernel? I am Asus T91mt with GMA500, Ubuntu 12.04.1. I would like too see only a notice of connection at least. A log of xrandr: $ lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation System Corporation System Controller Hub (SCH Poulcbo) Graphics Controller (rev 07) vp@vc:~$ xrandr --verbose xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 (0x138) normal (normal) 0mm x 0mm Identifier: 0x137 Timestamp: 26863 Subpixel: unknown Clones: CRTC: 0 CRTCs: 0 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: 1024x600 (0x138) 0.0MHz *current h: width 1024 start 0 end 0 total 1024 skew 0 clock 0.0KHz v: height 600 start 0 end 0 total 600 clock 0.0Hz vp@vc:~$ xrandr --prop xrandr: Failed to get size of gamma for output default Screen 0: minimum 1024 x 600, current 1024 x 600, maximum 1024 x 600 default connected 1024x600+0+0 0mm x 0mm 1024x600 0.0* vp@vc:~$ Please help, i am linux newbie and i am tired ;/

  Read the article

• Cannot scale frequency of a Core i7 2720QM

  - by user51414

  I own a Dell Latitude E6520 with an Intel CPU (Core i7 2720QM). After installing cpufrequtils, I get the following message : cpufrequtils 007: cpufreq-info (C) Dominik Brodowski 2004-2009 Veuillez rapportez les erreurs et les bogues à [email protected], s'il vous plait. analyse du CPU 0 : **pas de pilotes cpufreq reconnu pour ce CPU** maximum transition latency: 4294.55 ms. In English : no cpufreq pilot found for this CPU. Thus my CPU runs always at full speed (2,2 GHz) which consume the battery and shorten its life. I don't either know how to activate turbo mode. Please help ! Regards, Al

  Read the article

• Ubuntu 10.10 netbook Screen Resolution Sony Vaio FS315

  - by Fatos

  Hello, I've just installed ubuntu 10.10 on my laptop its all great but the screen resolution is a bit crap i have it set 1200:800 and when i do xrandr it indicates that the i can have a bigger screen resolution but i dont seem to to be able to increase it more 1200:800 through monitor tool. another interesting thing is that xorg.conf does not exist on the /etc/X11/ is there a way to increase the screen resolution for Sony laptops? The graphics card is Intel Graphics Please help! I didnt think it would be so hard to change the screen resolution

  Read the article

• xrandr shows VGA1 as disconnected

  - by Felix

  I have a Thinkpad W520 with Nvidia Optimus graphics. I have disabled the Nvidia card in BIOS (by selecting "integrated graphics"), so I'm running only on the integrated Intel graphics. I get full 3D acceleration, which would suggest the drivers are properly installed. However, I'm not able to use an external monitor. With the external monitor connected and turned on, running xrandr always gives: $ xrandr Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 8192 x 8192 LVDS1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 344mm x 193mm 1920x1080 60.0*+ 59.9 50.0 1680x1050 60.0 59.9 1600x1024 60.2 1400x1050 60.0 1280x1024 60.0 1440x900 59.9 1280x960 60.0 1360x768 59.8 60.0 1152x864 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) What gives? It sees the VGA1 port (to which the external display is connected), but it appears disconnected. I have tried forcing a resolution as per these instructions, but when I do that X becomes unresponsive and I have to Ctrl-Alt-F1 and restart it.

  Read the article

• No HDD shows up during install 12.04 on Lenovo U410

  - by varunthacker

  I tried installing Ubuntu 12.04 on my Lenovo U410 laptop. When I launch installation no partitions shows up. The U410 has 2 HDDs. 32 GB SSD on /dev/sda and a 500 HDD on /dev/sdb Ideally I would like to install Ubuntu on the 32GB SSD and keep Windows on the 500 GB one and not use the Intel Smart Response Technolog. I'm ok with flashing my drive and starting from scratch with this. Or do you'll have any better suggestions on how to go about partitioning my drive and how to do it?

  Read the article

• Vmware 3D Acceleration Ubuntu 14.04

  - by Bowser5543

  I have installed Vmware Player 6.0.3 build-1895310. The problem I have is that when I run a Windows 7 Vm, it says that 3D support was disabled. (I can't read the exact report atm because it has a chance of crashing my machine.) I have the 3D support box enabled. Here is my graphics card: Mobile Intel® GM45 Express Chipset x86/MMX/SSE2. Can anyone tell me to install drivers or something? I can't find mine anywhere!

  Read the article

• Ubuntu 11.10 to 12.04 results in loss of N network capability - how to restore?

  - by user74273

  On Ubuntu 11.10, I had zero issues with N network detection and speed. I cannot remember whether the old driver was iwlagn or iwlwifi. This was with Ubuntu repository Linux kernel 3.0.0-22. Upon upgrading to Ubuntu 12.04, iwlwifi is the available driver and while it detects N networks, upon connection, the speed is cripplingly low and DNS look-ups do not occur (impossible to browse). This is with Ubuntu repository Linux kernel 3.2.0-26. Please note that the 11n_disable flag for the iwlwifi module cannot work for me as I require N network access. Is there another solution? Perhaps, is there a way to easily patch the new kernel with the old wireless module (just copy-and-paste the iwlagn module into the new kernel source and re-compile)? Relevant hardware specs: Dell Inspiron N5110 Network Adapter: Intel® Centrino® Wireless-N 1030

  Read the article

• I`ve got some problems with new Acer Aspire S3

  - by xcariba

  I just got a new Acer Aspire S3 Laptop, and I've installed Ubuntu on it. Here is some problems: 1. Bluetooth (AR3012) can't find any devices. rfkill shows that everything is fine, but I still can't connect to any device. (Maybe it was turned off in stock windows?) 2. Can't change screen brightness (I've tried Timex's solution with new 3.2-rc kernel and some grub options, touchpad works fine,but I still can`t use Fn+Right/Left) 3. 720p video in all players(VLC, mplayer and totem) works wrong. I found some similar problems on intel video chips with vblank sync or something like that. Video plays as it should, but i always see a line which appears on action scenes (looks like some parts of a screen updates faster) Maybe there are some solutions from similar laptops that I can find? PS I've tried ubuntu 11.04 with old kernel and linux mint 12-rc with 3.2-rc2 kernel.

  Read the article

• gnome shell with very high CPU usage

  - by 501 - not implemented

  i'm running ubuntu gnome 13.10 on my dell latiude e6510 with a i5 m560. The I5 comes with a embedded Intel HD 3400 Graphics. The average cpu usage of the gnome-shell is by 160% it's to high, I think. Is there a problem with a driver? If i call the command glxinfo | grep OpenGL it returns: OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 128 bits) OpenGL version string: 2.1 Mesa 9.2.1 OpenGL shading language version string: 1.30 OpenGL extensions: Greetings

  Read the article

• How do I read my PDFs and watch videos properly again?

  - by asp

  Whenever I watch videos, either online of local via Totem and/or open PDF files using evince. The system gets really, really bogged down. All apps get really slow, menus take forever to display, switching windows gives me time to make a coffee, etc. I have a couple of bug reports open on this, but what do I need to do to really troubleshoot the issue? I've purged Adobe Flash from the system, but YouTube HTML5 videos still have the issue. A bunch of PDFs saved locally trigger the problem. And to (temporarily) remove the slowness, I need to shutdown the computer, breath for a few minutes, then restart. A simple reboot does not do the trick. How can I identify the cause? This only started on 13.04. I've had Ubuntu on this machine for a year without a problem until "upgrading" to 13.04. I am not a programmer, but I suspect an issue with the Intel video driver.

  Read the article

• How to install & upgarde my Video Drive in presice?

  - by user71382

  Greeting all out here, So one helpful folk during a troubleshoot on VirtualBox told me that my graphic driver is too old. Code: 00:00:02.714 OpenGL Info: Render SPU: GL_VENDOR: Tungsten Graphics, Inc 00:00:02.714 OpenGL Info: Render SPU: GL_RENDERER: Mesa DRI Mobile Intel® GM45 Express Chipset x86/MMX/SSE2 00:00:02.714 OpenGL Info: Render SPU: GL_VERSION: 2.1 Mesa 8.0.2 In try to shot the problem, I got at http://intellinuxgraphics.org/2012.02.html But now I don't know how to proceed & what to download & how to install the latest driver for my video card ????????????/ Any help on the matter is appreciated. Thank you,Have a nice day, Mrinal

  Read the article

• in ubuntu 12.04 how may i know if my devices have it's driver installed??

  - by Aldo

  i have a dell N4110 laptop, and i want to know if the driver is installed and working well, something like the device manager in windows , or another way to know if a device is driverless or if the device might have a better driver, like my mousepad, in windows it have multi-touch gestures , that scrolls or zoom with two fingers (like an ipod) but in ubuntu it just works the right part as a scroll bar, so maybe it is installed one driver, but i need other one that uses well my devices. and the grphics card, i have not idea if it is well installed or isn't. i have a Intel 3000hd graphics card. thank you for your time. have a nice day people! =D

  Read the article

• How to force GNOME panels et. al. to display on a different monitor without mirroring?

  - by GrueKun

  So, I recently purchased a new 23" monitor for my PC. However, I can't use it with the PC currently as I am waiting on a replacement heatsink. In the mean time, I wanted to use it with my Dell laptop. I hooked it up to the VGA port, and it seems to be working properly. However, I wanted to know if there was a way I could move all of the main display elements over to the attached monitor? I wanted to shut the LCD panel off on the laptop and hook it up like a desktop. Relevant specs: Ubuntu 10.10 x64 Intel graphics chipset The attached monitor is currently set as the default monitor. Any suggestions are welcome. :)

  Read the article

• Install Ubuntu on iMac 21.5" (mid 2011)

  - by Mystic Mark le Maverick

  I has a dual boot system with MacOSX 10.8.2 and Microsoft Windows 7 Home Premium x64. I would like to install Ubuntu alongside the two existing operating systems for cross platform development purposes. My System specs are listed below. iMac 21.5-inch (mid 2011) Intel Core i7 @2.80GHz AMD Radeon HD 6770M Facetime HD Internet Camera Thunderbolt port Wireless Airport adapter card Apple 8x Superdrive Apple Magic Mouse and wired keyboard with numeric keypad Will rEFIt install properly on my machine too? Thanks you very much for the help.

  Read the article

• How come ASUS sells Ubuntu installed 1225Cs, when we dont have drivers for gma3600?

  - by sumit_gt

  I recently purchased a ASUS 1225C cedar trail netbook. It didn't come preinstalled with Ubuntu like it comes in some markets. I installed Ubuntu 12.04 LTS on it. While Ubuntu works just fine, I am bothered by the lack of proper graphics support because of intel gma 3600. I am aware that this is not a problem of Ubuntu. My question is this: How does ASUS manage to sell these netbooks in other markets with Ubuntu preinstalled? How does ASUS manage to get everything to work? And if they can, why aren't I able to do the same? link: For more on Asus 1225C As you can see, they show Ubuntu working perfectly in the screenshots. Is this false advertising?

  Read the article

• How to set up multiple GPUs (12.04)?

  - by Brother Erryn

  I have two GPUs: one Intel i915 integrated, and one NVIDIA 560 Ti. This is NOT a hybrid setup, nor a laptop. In Windows 7, each card is connected to a different monitor, with the NVIDIA doing any "heavy lifting". For the life of me I cannot get Ubuntu to recognize the i915, but when logging off or rebooting, the shutdown actually appears on the i915. lshw lists both. I'm running the "current" NVIDIA drivers (not the experimental), but Displays calls its monitor a "Laptop". Is this even possible under Ubuntu? The only things that even looked like potential solutions were for laptop hybrid setups and used Bumblebee, but that doesn't seem to apply here.

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >