Search Results

Search found 19848 results on 794 pages for 'network infrastructure'.

Page 47/794 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

  • Problems with wired ethernet connection Ubuntu 11.10

    - by Andrew Fielden
    After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

    Read the article

  • Wifi - wireless network not working after installing Ubuntu 12.04

    - by Nilesh
    I had installed ubuntu 12.04 in my Dell Vostro 3460. Initially wired as well wireless both are not working. After installing compat-wireless-2012-07-03-pc.tar.bz2 wired network fine but wireless is not working. Previously both were working fine with ubuntu 11.10. Also presently both network are working fine in Win7. lspci: 00:00.0 Host bridge: Intel Corporation Ivy Bridge DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Ivy Bridge PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.4 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 5 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 0de9 (rev a1) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Atheros Communications Inc. AR8161 Gigabit Ethernet (rev 10) iwconfig: lo no wireless extensions. eth0 no wireless extensions. ifconfig: eth0 Link encap:Ethernet HWaddr 84:8f:69:d4:35:9b inet addr:10.24.22.72 Bcast:10.24.31.255 Mask:255.255.224.0 inet6 addr: fe80::868f:69ff:fed4:359b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15332 errors:0 dropped:0 overruns:0 frame:0 TX packets:10425 errors:0 dropped:0 overruns:0 carrier:1 collisions:0 txqueuelen:1000 RX bytes:9262594 (9.2 MB) TX bytes:1572030 (1.5 MB) Interrupt:16 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1432 errors:0 dropped:0 overruns:0 frame:0 TX packets:1432 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145656 (145.6 KB) TX bytes:145656 (145.6 KB)

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Intermittent ethernet connectivity

    - by Amey Jah
    I am facing a weird problem. I am connecting to my dsl modem via ethernet. After booting, sometimes Ubuntu 10.10 does not detect the eth0 card properly or does not connect to the modem. I have made the following observations: My modem is fully on. All indicators are on except ethernet, which is blinking continuously. My network indicator applet informs me that I am connected to modem, but I am not able to browse as it has not established connection with modem. I need to power off and on (restart) the modem several times OR disconnect/connect (via network applet) several times, before the system can establish a connection with the modem. Once it establishes the connection, the ethernet LED (on modem) stops blinking and glows continuously. However, I do not see this problem every time I reboot or start my computer. 3/5 time, it connects to the modem in a single attempt. Friends, I am not able to understand root cause of this problem. Plus I do not know what kind of logs should be attached. If you want any logs please give me command to run, and I will paste the result for you. Note: I ran system testing when above problem happened. Follow this link to download result.

    Read the article

  • my application did not show toast mesage when network is not available [closed]

    - by Smart Guy
    my application did no show toast message when network is disable if (position == 2) { final ConnectivityManager connMgr = (ConnectivityManager) getSystemService(Context.CONNECTIVITY_SERVICE); NetworkInfo activeNetworkInfo = connMgr .getActiveNetworkInfo(); android.net.NetworkInfo mobile1 = connMgr.getNetworkInfo(ConnectivityManager.TYPE_MOBILE); if (activeNetworkInfo == null) { Toast.makeText(LoginScreen.this, "No Active Network",Toast.LENGTH_LONG).show(); } else { if (activeNetworkInfo.isConnected()) { btnLogin.setOnClickListener(new OnClickListener() { public void onClick(View view) { String pinemptycheck = pin.getText().toString(); String mobileemptycheck = mobile.getText().toString(); if (pinemptycheck.trim().equals("")||(mobileemptycheck.trim().equals(""))) { Toast.makeText(getApplicationContext(), "Please Enter Correct Information", Toast.LENGTH_LONG).show(); } else { showProgress(); postLoginData(); } } }); } else if (activeNetworkInfo.isConnectedOrConnecting()) { Toast.makeText(LoginScreen.this, "network is Connecting", Toast.LENGTH_LONG) .show(); else if (mobile1.isAvailable()) { btnLogin.setOnClickListener(new OnClickListener() { public void onClick(View view) { showProgress(); postLoginData(); } }); } else if (!mobile1.isAvailable()) { Toast.makeText(LoginScreen.this,"No other Connection Found ",Toast.LENGTH_LONG).show(); btnLogin.setOnClickListener(new OnClickListener() { public void onClick(View v) { Toast.makeText(LoginScreen.this," No other Connection Found", Toast.LENGTH_LONG).show(); } }); }}}

    Read the article

  • set tap0 using virt-manager for bridged wireless

    - by DaveO
    After 3 days I finally have kvm guests working on the network via wireless (link below - thanks!): My network is 192.168.1.0/24 on the host: sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward" sudo tunctl -t tap0 sudo ip link set tap0 up sudo ip addr add 192.168.1.25/24 dev tap0 sudo route add -host 192.168.1.30 dev tap0 sudo parprouted wlan0 tap0 on the guest: auto eth0 iface eth0 inet static address 192.168.1.30 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.25 and start the guest: sudo kvm /path/to/guest.img -net nic,macaddr=DE:AD:BE:EF:90:26 -net tap,ifname=tap0,script=no This works great and I can ping the local network and the internet back and forth between the guest. But how do I add these settings to the guest's xml config so I can start the guest via virt-manager with the same nic settings? ref: http://www.linuxquestions.org/questions/debian-26/kvm-wireless-bridge-network-691953/

    Read the article

  • Network: Incoming connections work, outgoing fails

    - by anirvan
    i recently set up my own server at home to run Ubuntu 12.04 server ed. on booting up, i noticed that a message related to networking comes up, and the booting process pauses. the message read something like - waiting for network configuration and after a while - waiting another 60 seconds... on booting up, I realised that any command which requires a network connection was not working - ping, apt-get install, etc. on firing the ifup eth0 command, I get the error RTNETLINK answers: File exists. Failed to bring up eth0. I also realised, while searching the web for this problem, that this is probably one of the most common networking related issues - however, most of the questions are around setting up multiple IPs for the same machine. ifdown eth0 also fails, stating that eth0 is not configured. my /etc/network/interfaces file has a simple configuration for a static IP: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx gateway xx.xx.xx.xx dns-nameservers xx.xx.xx.xx The strangest part of this problem is that, while I can't connect to anything outside, I can ping to this particular server using the static IP configured in the interface file, and, i can even SSH into it! I'm really at ends here with this problem, and any guidance is much appreciated. Thanks!

    Read the article

  • How do I connect to a wireless network?

    - by Keith Groben
    I just installed 10.10 x64 and cannot even find my wireless network let alone connect to it. I've searched all over SE and Ubuntu forums and cannot find out how to do this simple thing. Can some one please give me the answer? It is plugged in right now and is 100% updated. It is a Desktop with wireless card. 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Here's the output: *-network DISABLED description: Wireless interface product: RT2860 vendor: RaLink physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 70:1a:04:f4:de:e9 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=2.6.35-27-generic firmware=N/A latency=0 link=yes multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:fcff0000-fcffffff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 03 serial: 00:23:54:fd:c2:32 size: 100MB/s capacity: 1GB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.14 latency=0 link=yes multicast=yes port=MII speed=100MB/s resources: irq:44 ioport:d800(size=256) memory:fceff000-fcefffff memory:ddffc000-ddffffff memory:fcec0000-fcedffff === Update === I have discovered that this is a know issue with the rt2860. I have been following step by step the instructions found here: http://www.ctbarker.info/2010/05/ubuntu-1004-wireless-chipsets-and-wpa.html I decided to stat over because I was getting stuck on step 5: 'sudo rmmod rt2860sta' is was giving me this problem: 'ERROR: Module rt2860sta does not exist in /proc/modules' Since I started over I cannot even get past step 5 'sudo make' I get this: 'make: * No targets specified and no makefile found. Stop.' I am lost. Any help would be appreciated.

    Read the article

  • Lost connectivity after configuring multiple network adapters on separate networks

    - by Dave Long
    I am trying to setup an Ubuntu hosting server, currently just for development, and the server has two NICs, each sitting on a different network. eth0 is on 192.168.200.* and eth1 is on 192.168.101.* and each one has a static IP. eth0 is the public facing NIC card and eth1 is strictly for internal access to the server. I initially only setup eth0 and added the eth1 card when I needed it. eth0 was working find until I added eth1, now, can't get any connectivity on eth0 unless I pull eth1 out of the box. The configuration on each system is as follows: auto eth0 iface eth0 inet static address 192.168.200.94 netmask 255.255.255.0 network 192.168.200.0 broadcast 192.168.200.255 gateway 192.168.200.253 auto eth1 iface eth1 inet static address 192.168.101.64 netmask 255.255.255.0 network 192.168.101.0 broadcast 192.168.101.255 gateway 192.168.101.254 Again eth0 worked fine until I added eth1. I have seen this happen with Windows servers if you have a Default Gateway setup for both NICs, but I am not sure if this works the same on Ubuntu. My resolv.conf file looks like so: nameserver 192.168.101.59 nameserver 192.168.101.58 domain domain.local search domain.local Per request here is the Routing table 192.168.101.0 * 255.255.255.0 U 0 0 0 eth1 192.168.200.0 * 255.255.255.0 U 0 0 0 eth0 default 192.168.101.254 0.0.0.0 UG 100 0 0 eth1 default 192.168.200.253 0.0.0.0 UG 100 0 0 eth0

    Read the article

  • Network(ing) to the Limit

    - by Oracle OpenWorld Blog Team
     By Karen Shamban While Oracle OpenWorld attendees are networking, there's an Oracle Global IT team that builds and maintains the massive networks that help run the show. The objective? To keep things running as seamlessly and smoothly as possible, constantly evaluate priorities, mitigate risk, and be ready for whatever might happen -- because things do happen when there are 50,000 plus attendees, tens of thousands of devices, unexpected requirements, and a constant flow of up-to-the-minute information. Here's just some of what it takes to keep the conference going, network style: 100 Oracle network, voice, and desktop engineers; security, risk management, and other IT experts, who come in from 17 countries  1000+ network switches 300+ miles of copper and fiber 485 wireless access points 2,500 wired laptops 300 VoIP phones And just where are all these networks and devices deployed? This is what the team had to build and manage: Moscone North, South, and West, including: The keynote hall Oracle DEMOgrounds in the Exhibition Halls Hundreds of session rooms Connection Centers, Social Avenue, Lounges Registration The Howard Street Tent and Taylor Street Cafe tented venues Oracle Square (Union Square) Yerba Buena Gardens Masonic Auditorium Sessions and demos at 8 hotel venues That's a whole lot of networking going on. And here's the kicker: the team has only 4 days to bring get it all up and running across these many venues, and exactly 12 hours to take it all down once the show ends. The Global IT team puts in the equivalent of 152 24-hour days for set-up, 227 24-hour days of support during the conferences, and then tears it all down in about 20 24-hour days. And in case you were wondering, the planning for next year's Oracle OpenWorld starts ... next week. No rest for the weary.  Now THAT's networking!  So hats off to the Global IT team -- the job ain't easy, but somebody's got to do it, and they do it remarkably well.

    Read the article

  • Network/browser issues after upgrade to 12.04

    - by Reg
    I let my laptop upgrade to 12.04. And have no network afterwards. I went through all the articles I could find in google. Right now, I can ping google, and yahoo, but not cnn.com for example or anything else. Firefox says it can't reach google.com or gmail.com (or anything, not even IP. /etc/network/interfaces dns-nameservers 8.8.8.8 <<<<<added auto lo iface lo inet loopback /etc/dhcp/dhclient.conf #prepend domain-name-servers 8.8.8.8,8.8.4.4; prepend domain-name-servers 127.0.0.1; <<<<< tried both /etc/NetworkManager/NetworkManager.conf with and without dns=dnsmasq commented out. I can ping my wireless router and connect to it just fine. Have tried proxy/noproxy. This looks like After Upgrade to 12.04 - cannot connect to network but no answer there. I would hate to do a fresh install. Any assistance appreciated.

    Read the article

  • How to get ISA 2006 Web Proxy to work with the Single Network Adapter template

    - by tronda
    I need to test an issue with running our application behind a proxy server with different type of configurations, so I installed ISA 2006 Enterprise on a desktop computer. Since this computer only has a single network card and I want to start out easy, I chose the "Single Network Adapter" template. We have a internal NAT'ed network which is in the 10 range. I have defined the internal network on the ISA server to be 10.XXX.YY.1 - 10.XXX.YY.255 I also have the Default rule which denies all traffic, but I've added the following Rule: Policy - Protocols - From - To Accept HTTP Internal External HTTPS Local Host Internal HTTS Server Localhost Then I configured Internet Explorer on a virutal machine running XP within virtualbox with Brigded network (gets same network address range as regular computers on our network) similar to this Instead of the server name I used the IP address. When I try to access a web page, this doesn't go through and I get the following log messages on the proxy server: Original Client IP Client Agent Authenticated Client Service Referring Server Destination Host Name Transport HTTP Method MIME Type Object Source Source Proxy Destination Proxy Bidirectional Client Host Name Filter Information Network Interface Raw IP Header Raw Payload GMT Log Time Source Port Processing Time Bytes Sent Bytes Received Cache Information Error Information Authentication Server Log Time Client IP Destination IP Destination Port Protocol Action Rule Result Code HTTP Status Code Client Username Source Network Destination Network URL Server Name Log Record Type 10.XXX.YY.174 - TCP - - - 24.08.2010 13:25:24 1080 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.174 10.XXX.YY.175 80 HTTP Initiated Connection MyHTTPAccess 0x0 ERROR_SUCCESS Internal Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:24 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:24 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2275 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:25 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:25 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2276 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:26 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Initiated Connection 0x0 ERROR_SUCCESS Local Host Local Host - PROXYTEST Firewall 10.XXX.YY.159 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.159 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 10.XXX.YY.166 - UDP - - - 24.08.2010 13:25:26 68 0 0 0 0x0 0x0 - 24.08.2010 06:25:26 10.XXX.YY.166 255.255.255.255 67 DHCP (request) Denied Connection [Enterprise] Default rule 0xc004000d FWX_E_POLICY_RULES_DENIED Internal Local Host - PROXYTEST Firewall 0.0.0.0 Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729) Yes Proxy 10.XXX.YY.175 TCP GET Internet - - - Req ID: 096c76ae; Compression: client=No, server=No, compress rate=0% decompress rate=0% - - - 24.08.2010 13:25:27 0 2945 2581 446 0x0 0x40 24.08.2010 06:25:27 10.XXX.YY.174 10.XXX.YY.175 80 http Failed Connection Attempt MyHTTPAccess 10061 anonymous Internal Local Host http://www.vg.no/ PROXYTEST Web Proxy Filter 10.XXX.YY.175 - TCP - - - 24.08.2010 13:25:27 2277 0 0 0 0x0 0x0 - 24.08.2010 06:25:27 10.XXX.YY.175 10.XXX.YY.175 80 HTTP Closed Connection 0x80074e20 FWX_E_GRACEFUL_SHUTDOWN Local Host Local Host - PROXYTEST Firewall

    Read the article

  • Oracle Social Network and the Flying Monkey Smart Target

    - by kellsey.ruppel
    Originally posted by Jake Kuramoto on The Apps Lab blog. I teased this before OpenWorld, and for those of you who didn’t make it to the show or didn’t come by the Office Hours to take the Oracle Social Network Technical Tour Noel (@noelportugal) ran, I give you the Flying Monkey Smart Target. In brief, Noel built a target, about two feet tall, which when struck, played monkey sounds and posted a comment to an Oracle Social Network Conversation, all controlled by a Raspberry Pi. He also connected a Dropcam to record the winner just prior to the strike. I’m not sure how it all works, but maybe Noel can post the technical specifics. Here’s Noel describing the Challenge, the Target and a few other tidbit in an interview with Friend of the ‘Lab, Bob Rhubart (@brhubart). The monkey target bits are 2:12-2:54 if you’re into brevity, but watch the whole thing. Here are some screen grabs from the Oracle Social Network Conversation, including the Conversation itself, where you can see all the strikes documented, the picture captured, and the annotation capabilities: #gallery-1 { margin: auto;? } #gallery-1 .gallery-item { float: left; margin-top: 10px; text-align: center; width: 33%; } #gallery-1 img { border: 2px solid #cfcfcf; } #gallery-1 .gallery-caption { margin-left: 0; }    That’s Diego in one shot, looking very focused, and Ernst in the other, who kindly annotated himself, two of the development team members. You might have seen them in the Oracle Social Network Hands-On Lab during the show. There’s a trend here. Not by accident, fun stuff like this has becoming our calling card, e.g. the Kscope 12 WebCenter Rock ‘em Sock ‘em Robots. Not only are these entertaining demonstrations, but they showcase what’s possible with RESTful APIs and get developers noodling on how easy it is to connect real objects to cloud services to fix pain points. I spoke to some great folks from the City of Atlanta about extending the concepts of the flying monkey target to physical asset monitoring. Just take an internet-connected camera with REST APIs like the Dropcam, wire it up to Oracle Social Netwok, and you can hack together a monitoring device for a datacenter or a warehouse. Sure, it’s easier said than done, but we’re a lot closer to that reality than we were even two years ago. Another noteworthy bit from Noel’s interview, beginning at 2:55, is the evolution of social developer. Speaking of, make sure to check out the Oracle Social Developer Community. Look for more on the social developer in the coming months. Noel has become quite the Raspberry Pi evangelist, and why not, it’s a great tool, a low-power Linux machine, cheap ($35!) and highly extensible, perfect for makers and students alike. He attended a meetup on Saturday before OpenWorld, and during the show, I heard him evangelizing the Pi and its capabilities to many people. There is some fantastic innovation forming in that ecosystem, much of it with Java. The OTN gang raffled off five Pis, and I expect to see lots of great stuff in the very near future. Stay tuned this week for posts on all our Challenge entrants. There’s some great innovation you won’t want to miss. Find the comments. Update: I forgot to mention that Noel used Twilio, one of his favorite services, during the show to send out Challenge updates and information to all the contestants.

    Read the article

  • Django URL resolving infrastructure stops working

    - by btol45
    We recently launched a new Django-powered website, and we are experiencing the oddest bug: The site is running under Apache with mod_fastcgi. Everything works fine for a while, and then the URL tag and reverse() functionality stops working. Instead of returning the expected URL, they return "". We haven't noticed anything in Apache's log file; there are no errors being generated by Django. And (the kicker) the problem only occurs in production mode; we can't reproduce it when DEBUG=True. Any thoughts on where we should be looking for the problem?

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • Windows Server Hyper-V guests cannot see each other on network

    - by Noldorin
    I have a Hyper-V physical machine along with two standard laptops running within my LAN (connected by an ASUS-RT56U router). The physical server runs Windows Hyper-V Server 2008 R2, with two Windows Server 2008 R2 (full) guest VMs installed and running within. Both laptops run Windows 7. All OSs are 64-bit. Opening up Network in Windows Explorer on either of the two laptops displays both of the laptops in the LAN fine. However, neither of the guest VMs on the server (nor the host itself) are displayed. Indeed, the guest VMs can not see each other in Network view either. I can ping all computers (laptops and servers) without problems from within the LAN, but all of the servers are simply not visible from anywhere. In addition, the Network Map screen (accessible via Network and Sharing centre) gives me an error message: "An error happened during the mapping process." And I'm suspecting this might have something to do with how LLTP (Link Layer Topology Protocol) is working on the network. Worth noting though is that before my server was on the network, the Network Map screen displayed fine (as far as I can remember).

    Read the article

  • video streaming infrastructure

    - by alchemical
    We would like to set-up a live video-chat web site and are looking for basic architectural advice and/or a recomendation for a particular framework to use. Here are the basic features of the site: Most streams will be broadcast live from a single person with a web cam, etc., and viewed by typically 1-10 people, although there could be up to 100+ viewers on the high side. Audio and video do not have to be super-high quality, but do need to be "good enough". The main point is to convey the basic info in the video (and audio). If occasionally the frame-rate drops low and then goes back to normal fairly soon, we could live with that. Budget is an issue, so we are in general looking for a lower cost solution that will give us most of what we need in temers of performance and quality. We are looking at Peer1 for co-lo. The rest of our web site will be .Net / Windows platform. We are open to looking at any platform for the best streaming solution, although our technical expertise is currently more on the Windows side.

    Read the article

  • How can one setup a version control system on a local network, without a server?

    - by Andrew
    Edit: Ok so I learned that I guess I need an distributed source control, however are there any UI based ones, and do they allow you to merge with other users on the network? This is kind of a two part question, so here it goes. I want to start developing a web application at home (with multiple developers). However, I don't have a dedicated server nor want to pay for on. So first, I don't know which version control system to use for this case, as at work we mostly have TFS setup, so I am not to familiar with whats out there. What are the best free CVS/SVN tools out there? Second, is it possible to somehow setup the CVS/SVN where there is no dedicated server and both clients store up to one week of the source code from the last check-in? Also, it would be helpful if it could integrate with visual studio, again this isn't that important at all. Problem: There are Five users, one is a Server. Server Connected: All Ok Server Disconnected: No one can share. What I am looking for: No Server: Users still have versioning based on version id of last check-in. Users must check all version on network to make sure they aren't outdated based on their last version id. If not check-in, otherwise merge/get latest. If they are update checkin, and set current version id +1.

    Read the article

  • Windows XP can't connect to wireless network

    - by mikez302
    I have a desktop computer with a wireless card, running Windows XP SP3. For a little while, I had a remote network connection set up for my job, but I didn't need the remote connection so I deleted it. Now, I am unable to connect to the internet at all from that computer through my wireless router. I can connect through my router using my laptop, and I can connect through my neighbor's router using my desktop, but for some reason I can't connect through my own router using my desktop. I see the "Wireless Network Connection 5" icon in my system tray, but it tells me it is not connected. When I click on the icon, I see a list of wireless networks, including my own, which is set up to automatically connect, although it doesn't. When I try to connect to my network on my own (by clicking on it, then clicking "Connect"), it asks me for my network password like it usually does. I see a box come up saying "Waiting for network to be ready..." and it hangs there. On the list of wireless networks, my network says "Acquiring network address" but it doesn't actually connect. How can I fix this? I tried rebooting my computer, repairing my connection, and restarting my router, and I am still having this problem.

    Read the article

  • How do I disable the network connection from .Net without needing admin priveledges?

    - by Brad Mathews
    I may be SOL on this but I thought I would give throw it out for possible solutions. I am writing a computer access control service to help me control my kids' computer use. Plan on open sourcing it when I have it working. It is written in VB.Net and needs to work on XP through 7. I am running into all sorts of security and desktop access issues on Windows 7. The service needs to run as admin to execute the NetSh command to disable the network. But I cannot interact with the desktop from the service so I IPC to a UI to handle other stuff, but I still cannot detect from the service if the desktop is locked. Argghh! I could get it all working from a hidden windows form app if I could just lick the one piece that needs admin permissions: disabling the network. It does no good if a kid logs on and denies the popup asking if the program should run as administrator and he says no. Also windows 7 will not start a program set to run as admin using HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run Anyone know how to get this working? Or have an outside the box solution? Thanks! Brad

    Read the article

  • Virtual Machine Network Architecture, Isolating Public and Private Networks

    - by Mark
    I'm looking for some insight into best practices for network traffic isolation within a virtual environment, specifically under VMWARE ESXi. Currently I have (in testing) 1 hardware server running ESXi but i expect to expand this to multiple pieces of hardware. The current setup is as follows: 1 pfsense VM, this VM accepts all outside (WAN/internet) traffic and performs firewall/port forwarding/NAT functionality. I have multiple public IP addresses sent to the this VM that are used for access to individual servers (via per incoming IP port forwarding rules). This VM is attached to the private (virtual) network that all other VMs are on. It also manages a VPN link into the private network with some access restrictions. This isn't the perimeter firewall but rather the firewall for this virtual pool only. I have 3 VMs that communicate with each other, as well as have some public access requirements: 1 LAMP server running an eCommerce site, public internet accessible 1 accounting server, access via windows server 2008 RDS services for remote access by users 1 inventory/warehouse management server, VPN to client terminals in warehouses These servers constantly talk with each other for data synchronization. Currently all the servers are on the same subnet/virtual network and connected to the internet through the pfsense VM. The pfsense firewall uses port forwarding and NAT to allow outside access to the servers for services and for server access to the internet. My main question is this: Is there a security benefit to adding a second virtual network adapter to each server and controlling traffic such that all server to server communication is on one separate virtual network, while any access to the outside world is routed through the other network adapter, through the firewall, and on the the internet. This is the type of architecture i would use if these were all physical servers, but i'm unsure if the networks being virtual changes the way i should approach locking down this system. Thank you for any thoughts or direction to any appropriate literature.

    Read the article

  • Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

    - by Rhys
    I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7.

    Read the article

  • Adding a Printer to my Print Server Failing

    - by Rudi Kershaw
    So, on the Windows Server page I read the following. Step 4: Add Network Printers Automatically Print Management (Printmanagement.msc) can automatically detect all the printers that are located on the same subnet as the computer on which you are running Print Management, install the appropriate printer drivers, set up the queues, and share the printers. To automatically add network printers to a printer server Open the Administrative Tools folder, and then double-click Print Management. In the Printer Management tree, right-click the appropriate server, and then click Add Printer. On the Printer Installation page of the Network Printer Installation Wizard, click Search the network for printers, and then click Next. If prompted, specify which driver to install for the printer. So, I have got to this point, made sure the printer (Canon MP620) is on and correctly plugged into the network. However, when I click "Search the network for printers", the wizard doesn't find it. Now, I can't get any further. Is there anything I could be doing wrong? How should I proceed moving forwards?

    Read the article

  • Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

    - by Bill
    I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

    Read the article

  • Slackware - Assigning routes (IP address ranges) to one of many network adapters

    - by Dogbert
    I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

    Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >