Search Results

Search found 21455 results on 859 pages for 'setup exe'.

Page 47/859 | < Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >

• Computer hangs at BIOS screen. Cannot enter setup

  - by d2jxp

  I have an HP Pavilion a6500f (it's a year out of warranty) and it's hanging on the blue HP BIOS screen. If I mash F10 while it's starting up, it will say "Entering Setup..." but I will see no results. It will hang there and not do anything. If I actually wait until I can see the screen and then hit F10, there's no response at all and the computer will sit at the BIOS menu. I've dusted and cleaned it out, reseated the memory, switched the RAM slots, and reset the CMOS battery using the reset jumper. I'm out of ideas. I'm pretty sure it's not a hard drive issue, since my problem is at the BIOS. After this post, I'll disconnect the hard drive and try to just boot without it. Anyone have any other ideas? Edit: Okay, so I tried disconnecting the hard drive and now I can get back into the BIOS. I reconnected it and I'm locked out again. So the problem is my hard drive.. I guess I should delete this post unless someone has any ideas as to what's wrong with the drive?

  Read the article

• How to setup Joomla CMS as a backend for iPhone app

  - by srik

  I would like my iPhone app to get dynamic content off the net. This content should be managed using a CMS. I have gone ahead and installed Joomla on my server and will be using the Joomla web interface to create and manage content. I would now like the iPhone app to login to my server and fetch the content. I do not want the complete web pages for my iPhone app. Instead, I want the content in the form of XML or JSON or some serialized format so that I can use the data in a custom layout native to the app. So I am looking for 2 things in particular: 1. How to setup HTTP based authentication for my iPhone app to access data from my server. 2. How to access the content in a serialized format (XML, JSON etc) Are there plugins/extensions/components I can use to achieve the same. Any advice on how this can be achieved would be helpful. I am completely new to setting up/using CMS.

  Read the article

• How to setup Joomla CMS as a backend for iPhone app

  - by srik

  I would like my iPhone app to get dynamic content off the net. This content should be managed using a CMS. I have gone ahead and installed Joomla on my server and will be using the Joomla web interface to create and manage content. I would now like the iPhone app to login to my server and fetch the content. I do not want the complete web pages for my iPhone app. Instead, I want the content in the form of XML or JSON or some serialized format so that I can use the data in a custom layout native to the app. So I am looking for 2 things in particular: 1. How to setup HTTP based authentication for my iPhone app to access data from my server. 2. How to access the content in a serialized format (XML, JSON etc) Are there plugins/extensions/components I can use to achieve the same. Any advice on how this can be achieved would be helpful. I am completely new to setting up/using CMS.

  Read the article

• Server installation logging / logbook / diary?

  - by The MYYN

  Are there some ways field-tested ways to keep a kind of logbook for a server? Including: software installations (and de-installations) custom configurations (e.g. of a webserver, ssh daemon, etc.) personal notes The big picture. I am preparing a server and would like to extensively document the state and how it was established over time, so that a new person can easily see, what's going on and why. The setup is not too complicated, but I would like to do it anyway. I once used something like Maintain /etc with mercurial on Debian and it was nice, but I am looking for a little more flexible solution. Addendum: So I am interested in logging and documentation first. In an ideal world however, I would like to have a command, which in a few steps would take me from a bare newly installed unix system to a functional environment with all the components setup and in place by the means of, say an 'executable' log. But that would be very ideal, I imagine.

  Read the article

• How can I tell which "explorer.exe" process is the main one?

  - by HodofHod

  I have a batch file that changes a few registry files, and then restarts explorer.exe so that they take effect. I'm using the command taskkill /f /im explorer.exe and then explorer.exe which of course kills all the explorer.exe processes, including the explorer windows I have open. Obviously, I am using the option to Launch folder windows in a separate process. Is there any way I can determine which instance of explorer.exe is the main one, and just kill that?

  Read the article

• Reverse NAT Setup for Hyper-V on Win 2008 R2

  - by sukru

  I'm trying to setup a Linux server behind a Windows Hyper-V host that will help supply some of the services (SSH, HTTPS, etc). However getting RRAS configured for reverse NAT (port forwarding) turned out to be a non trivial task. As a staring point, I tried forwarding port 22 (SSH) to the virtual machine. The virtual machine is on a public interface (i.e.: it also has a visible IP on the same network as the host). On RRAS management console I tried to add a rule, by adding "Local Area Connection" to NAT pool (Public Interface - Enable Nat), and an incoming rule for port 22 - :22. I also tried with the same port enabled on Windows Firewall (and not). The NAT management page tells there are "1 mappings" and "30+ Outbound packets transleted". However all other counters (Inbound packets translated, and respective rejected ones) are always zero. (I'm trying to access the server from an external machine). I can directly access the service if I give the VM's public IP, but not the host's one. Is there a way to enable this on RRAS?

  Read the article

• Winodws server 2003 Setup

  - by Barracksbuilder

  I work at a university maintaining the computer science department server. I am looking for a more economical way to stream line the set up of student accounts. CS students are granted a Username and password an IIS virtual directory, FTP virtual directory, and a mysql database. Server is running windows server 2003R2 (Possibly migrating to 2008R2) The server is running a domain though no students physically log a terminal into it (No computers are part of my domain.) Creating the account is a manual process. I did right a PHP script to query the Universities AD and copy the information and write it to my AD. I then have to create basically the users home directory. I tried having AD do it but since the user never physically logs in it never creates the directory. Permissions on this folder are set to User - full, Instructors (group) - full, Users (group) - read, IUSER - read. Inside of the users folder their is a "Private" folder with permissions User - full, instructors (group) - full. Next step is IIS I create a virtual directory in the default web site pointed to the users home directory so they have a website. Same goes for FTP virtual directory in the default ftp configuration to allow the users to upload files to their website. Mysql I have to create a user and password then create a mysql scheme (database) full access for the user and full access to the instructors account to be able to access the students database. All of this is done manually and takes me a week to do. The closest description is maybe a shared hosting environment. Is there a better way to do this? Scripting wise, or better structure setup?

  Read the article

• How can i add a checkbox for optional files during install? (innosetup)

  - by Globulorozzo

  i'm trying to make a custom checkbox in my custom page (because is a one page installer), is needed only a checkbox without dialogs or anything, the installer that i'm trying to compile is very linear and simple. i want to bind "FILE3.EXE" on a checkbox in this way: if checkbox is checked copy the file (FILE3.EXE) in DestDir, otherwise if checkbox is unchecked skip the file (FILE3.EXE) during installation. This is the code that i use, obviously the checkbox code is missing because i'm not able to do that [Files] Source: FILE1.EXE; DestDir: {app}; Source: FILE2.EXE; DestDir: {app}; Source: FILE3.EXE; DestDir: {app}; //OPTIONAL [Code] procedure ExitProcess(uExitCode: UINT); external '[email protected] stdcall'; var MainPage : TWizardPage; FolderToInstall : TEdit; InstallLocation : String; procedure CancelClick(Sender: TObject); begin if ExitSetupMsgBox then begin ExitProcess(0); end; end; procedure BrowseClick(Sender : TObject); var Dir : String; begin Dir := FolderToInstall.Text; if BrowseForFolder('Browse',Dir,false) then FolderToInstall.Text := Dir; WizardForm.DirEdit.Text := Dir; end; procedure InitializeWizard(); var LabelFolder : TLabel; begin WizardForm.ClientWidth:=ScaleX(550); WizardForm.ClientHeight:=ScaleY(250); WizardForm.Center; WizardForm.OuterNotebook.Hide; WizardForm.InnerNotebook.Hide; WizardForm.Bevel.hide; Wizardform.NextButton.top := 180; Wizardform.NextButton.Left := 470; WizardForm.NextButton.Height := 25; WizardForm.StatusLabel.Parent := WizardForm; WizardForm.StatusLabel.Left := 6; WizardForm.StatusLabel.Top := 206; WizardForm.FilenameLabel.Parent := WizardForm; WizardForm.FilenameLabel.Left := 87; WizardForm.FilenameLabel.Top := 206; WizardForm.FilenameLabel.Width := ScaleX(383); WizardForm.ProgressGauge.Parent := WizardForm; WizardForm.ProgressGauge.Left :=5; WizardForm.ProgressGauge.Top := 222; WizardForm.ProgressGauge.Width := ScaleX(460); MainPage := CreateCustomPage(wpWelcome,'',''); LabelFolder := TLabel.Create(MainPage); LabelFolder.Parent := WizardForm; LabelFolder.Top := 164; LabelFolder.Left := 6; LabelFolder.Caption := 'Directory:' FolderToInstall := TEdit.Create(MainPage); FolderToInstall.Parent := WizardForm; FolderToInstall.Top := 182; FolderToInstall.Left := 85; FolderToInstall.Width := 380; FolderToInstall.Text := WizardDirValue; FolderToInstall.ReadOnly := True; end;

  Read the article

• Super slow opening my downloads folder

  - by Mark

  I have an exe file in my download folder that I half downloaded through utorrent (it's not piracy, a legit file from people who use bittorrent to distribute large files). I think I tried to open it while it was still sharing, that is, did not stop the upload. That actually froze my computer. When I restart in utorrent I set the file to be deleted. Unfortunately even though utorrent doesn't see that file anymore, it's still visible in my download folder. Whenever I try to open my download folder it literally takes 10 minutes or more. It opens, but is empty and the blue progress bar needs a long time to complete. After completion I can use the download folder normally, but opening and closing things in that folder takes a long time. I see the exe that I tried to download. I tried to delete it. But it was taking so long 30+ minutes that I eventually just hit cancel. That doesn't even work, and it was slowing down the computer. Couldn't figure out how to stop the delete so I just pulled the plug. Should I just forget about that dl folder and set a new one? Is there something I can do? Thanks.

  Read the article

• Installing an exe with Powershell DSC Package resource gets return code 1619

  - by Jay Spang

  I'm trying to use Powershell DSC's Package resource to install an exe... Perforce's P4V to be specific. Here's my code: Configuration PerforceMachine { Node "SERVERNAME" { Package P4V { Ensure = "Present" Name = "Perforce Visual Components" Path = "\\nas\share\p4vinst64.exe" ProductId = '' Arguments = "/S /V/qn" # args for silent mode LogPath = "$env:ProgramData\p4v_install.log" } } } When running this, this is the error Powershell gives me: PowerShell provider MSFT_PackageResource failed to execute Set-TargetResource functionality with error message: The return code 1619 was not expected. Configuration is likely not correct + CategoryInfo : InvalidOperation: (:) [], CimException + FullyQualifiedErrorId : ProviderOperationExecutionFailure + PSComputerName : SERVERNAME According to documentation, return code 1619 means the MSI package couldn't be opened. However, when I manually log in to the machine and run "\\nas\share\p4vinst64.exe /S /V/qn", the install works flawlessly. Does anyone know why this is failing? Alternately, can anyone tell me how to troubleshoot this? I pasted all the error information I got from the terminal, my log file (p4v_install.log) is a 0 byte file, and there are no events in the event viewer. I don't know how to troubleshoot it any further! EDIT: I should note that I also tried using the File resource to copy the file locally, and then install it from there. Sadly, that met with the same result.

  Read the article

• new ActiveXObject('Word.Application') creates new winword.exe process when IE security does not allo

  - by Mark Ott

  We are using MS Word as a spell checker for a few fields on a private company web site, and when IE security settings are correct it works well. (Zone for the site set to Trusted, and trusted zone modified to allow control to run without prompting.) The script we are using creates a word object and closes it afterward. While the object exists, a winword.exe process runs, but it is destroyed when the word object is closed. If our site is not set in the trusted zone (Internet zone with default security level) the call that creates the word object fails as expected, but the winword.exe process is still created. I do not have any way to interact with this process in the script, so the process stays around until the user logs off (users have no way to manually destroy the process, and it wouldn't be a good solution even if they did.) The call that attempts to create the object is... try { oWordApplication = new ActiveXObject('Word.Application'); } catch(error) { // irrelevant code removed, described in comments.. // notify user spell check cannot be used // disable spell check option } So every time the page is loaded this code may be run again, creating yet another orphan winword.exe process. oWordApplication is, of course, undefined in the catch block. I would like to be able to detect the browser security settings beforehand, but I have done some searching on this and do not think that it is possible. Management here is happy with it as it is. As long as IE security is set correctly it works, and it works well for our purposes. (We may eventually look at other options for spell check functionality, but this was quick, inexpensive, and does everything we need it to do.) This last problem bugs me and I'd like to do something about it, but I'm out of ideas and I have other things that are more in need of my attention. Before I put it aside, I thought I'd ask for suggestions here...

  Read the article

• MSBuild on TeamCity Server can't find AL.exe

  - by Tim Long

  I'm having a problem on my TeamCity CI build server where during compilation I get the following error: C:\WINDOWS\Microsoft.NET\Framework\v4.0.30319\Microsoft.Common.targets(2342, 9): error MSB3086: Task could not find "AL.exe" using the SdkToolsPath "" or the registry key "HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Microsoft SDKs\Windows\v7.0A". Make sure the SdkToolsPath is set and the tool exists in the correct processor specific location under the SdkToolsPath and that the Microsoft Windows SDK is installed I've found similar reports from a year ago when people were upgrading to .NET 3.5, for example this one. In that case, installing the latest SDK solved the issue, however I have already installed the latest SDK (Microsoft Windows SDK for Windows 7 and .NET Framework 4) on my build server. The MSBuild tools are all there on the server, in a folder called C:\WINDOWS\Microsoft.NET\Framework\v4.0.30319 and AL.exe exists in C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\NETFX 4.0 Tools However the registry key mentioned in the error message does not exist. So, it seems like there is something wrong with the installation/configuration of MSBuild. This error only happens for projects that have embedded resources, which require AL.exe. Please, anyone solved this issue or have any clues what's wrong?

  Read the article

• Visual Studio Debugging is not attaching to WebDev.WebServer.EXE

  - by Aaron Daniels

  I have a solution with many projects. On Debug, I have three web projects that I want to start up on their own Cassini ASP.NET Web Development servers. In the Solution Properties - Common Properties - Startup Project, I have Multiple startup projects chosen with the three web applications' Action set to Start. All three web development servers start, and all three web pages load. However, Visual Studio is only attaching to two of the WebDev.WebServer.EXE processes. I have to manually go attach to the third process in order to debug it with the debugger. This behavior just started happening, and I'm at a loss as to how to troubleshoot this. Any help is appreciated. EDIT: Also to note, I have stopped and restarted the development servers several times with no change in behavior. Also, when attaching to the process manually, I see that the Type property of the two automatically attached WebDev.WebServer.EXE processes is Managed, while the Type property of the unattached WebDev.WebServer.EXE process is TSQL, Managed, x86. When looking at the project's properties, however, I am targeting AnyCPU, and do NOT have SQL Server debugging enabled. EDIT: Also to note, the two projects that attach correctly are C# web applications. <ProjectTypeGuids>{349c5851-65df-11da-9384-00065b846f21};{fae04ec0-301f-11d3-bf4b-00c04f79efbc}</ProjectTypeGuids> The project that is not attaching correctly is a VB.NET web application. <ProjectTypeGuids>{349c5851-65df-11da-9384-00065b846f21};{F184B08F-C81C-45F6-A57F-5ABD9991F28F}</ProjectTypeGuids> EDIT: Also to note, the behavior is the same on another workstation. So odds are that it's not a machine specific problem.

  Read the article

• autoconf libtool library linker path incorrect (need drive-letter) for MinGW ld.exe in Cygwin

  - by Tam Toucan

  I use autoconf and when the target is mingw I was using the -mno-cygwin flag. This has been removed so I'm trying to using the mingw tool chain. The problem is the linker isn't finding my libraries /bin/sh ../../../libtool --tag=CXX --mode=link mingw32-g++ -g -Wall -pedantic -DNOMINMAX -D_REENTRANT -DWIN32 -I /usr/local/include/w32api -L/usr/local/lib/w32api -o testRandom.exe testRandom.o -L../../../lib/Random -lRandom libtool: link: mingw32-g++ -g -Wall -pedantic -DNOMINMAX -D_REENTRANT -DWIN32 -I /usr/local/include/w32api -o .libs/testRandom.exe testRandom.o -L/usr/local/lib/w32api -L/home/Tam/src/3DS_Games/lib/Random -lRandom D:\cygwin\opt\MinGW\bin\..\lib\gcc\mingw32\3.4.5\..\..\..\..\mingw32\bin\ld.exe: cannot find -lRandom To link this from the command line using the mingw linker the -L path needs the drive letter i.e mingw32-ld testRandom.o -LD:/home/Tam/src/3DS_Games/lib/Random -lRandom works. The -L path is generated from the makefile.am's which have LDADD = -L$(top_builddir)/lib/Random -lRandom However I can't find how to set top_builddir to a relative path or to start it with the drive letter (my autoconf skills are weak). As a tempoary "solution" I have removed the use of libtool. I could hack a $(DRIVE_LETTER) infront of every -L option, but I'd like to find something better.

  Read the article

• ildasm and dynamic exe files

  - by TonyNeallon

  Hi There, I am trying to create an application can modify properties in IL to create a slightly different executable. E.g Client A runs app and a label on the WinForm label Reads "Client A:". Client B runs the app and Label Says "Client B". Easy I know using config files or resource files but thats not an option for this project. The Main program needs to be able to generate .exe file dynamically based on some form fields entered by user. My solution was to create a standalone executable that contained all the elements which I needed to make dynamic. I then used ildasm to generate the IL and thought that I could use this IL and substitute tags for the elements i wanted to make dynamic. I could then replace those tags at runtime after user filled the form using regex etc. The problem is, the if i re save the IL file generated by ILDASM as an exe and try to run it. I just launches console and does nothing. Am I going about this the wrong way? I didnt want to delve into Reflection as the dynamic .exe is a really simple one and I thought reverse engineering IL with ildasm would be the quickest way. You thoughts and pointers are much appreciated. Tony

  Read the article

• How to properly force a Blackberry Java application to install using Loader.exe

  - by Kevin White

  I want to include the Application Loader process in a software installation, to ensure that users get our software installed on their Blackberry by the time our installer software finishes. I know this is possible, because Aerize Card Loader (http://aerize.com/blackberry/software/loader/) does this. When you install their software, if your Blackberry is connected the Application Loader will come up and force the .COD file to install to the device. I can't make it work. Looking at RIM's own documentation, I need to: Place the ALX and COD files into a subfolder here: C:\Program Files\Common Files\Research In Motion\Shared\Applications\ Add a path to the ALX file in HKCU\Software\Research In Motion\Blackberry\Loader\Packages Index the application, by executing this at the command line: loader.exe /index Start the force load, by doing this: loader.exe /defaultUSB /forceload When I execute that last command, the Application Loader comes up and says that all applications are up to date and nothing needs to be done. If I execute loader.exe by double-clicking on it (or typing in the command with no parameters), I get the regular Application Loader wizard. It shows my program as listed, but un-checked. If I check it and click next, it will install to the Blackberry. (This is the part that I want to avoid, and that Aerize Card Loader's install process avoids.) What am I missing? It appears that the Aerize installer is doing something different but I haven't been able to ascertain what.

  Read the article

• Configuration file 'C:\my\App.Config' is being used to configure all executables

  - by Taylor Leese

  I have a Visual Studio setup project that installs an application into the task scheduler and also installs a GUI application to manage some configuration parameters in the registry. This being the case, the setup project installs two different primary outputs (.exe's) as part of the process. I am getting the following warning when I rebuild the setup project: Configuration file 'C:\my\App.Config' is being used to configure all executables Is there any way to remove this warning? The suggested MSFT solution apears to be to use a different setup project for each .exe, but I only want the users to have to run one installer. Any suggestions?

  Read the article

• iptables (NAT/PAT) setup for SSH & Samba

  - by IanVaughan

  I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - B1 = 192.168.109.15 B2 = 172.24.40.130 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Update after response from Eddie Few problems (and Machines' B IP is different!) From A :- ssh 172.24.40.130 works ok, (can get to B2) but ssh 172.24.40.130 -p 2022 -vv times out with :- OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.24.40.130 [172.24.40.130] port 2022. ...wait ages... debug1: connect to address 172.24.40.130 port 2022: Connection timed out ssh: connect to host 172.24.40.130 port 2022: Connection timed out From B2 :- $ service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 192.168.0.2 tcp dpt:22 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:2022 to:192.168.0.2:22 Chain POSTROUTING (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination And ssh from B2 to C works fine :- $ ssh 192.168.0.2 Route info :- $ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 172.24.40.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth1 default 172.24.40.1 0.0.0.0 UG 0 0 0 eth0 $ ip route 192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1 172.24.40.0/24 dev eth0 proto kernel scope link src 172.24.40.130 169.254.0.0/16 dev eth1 scope link default via 172.24.40.1 dev eth0 So I just dont know why the port forward doesnt work from A to B2?

  Read the article

• kernel panic after LVM setup

  - by Manuel Sopena Ballesteros

  I broke my webserver... My setup is: VMWare ESXi environemt CPanel installed CentOS release 6.5 (Final) 4 CPUs 2G RAM 2x VM disks 100G each LVM system This was my previous storage settings (the server was working fine at this time): # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_test01-lv_root 95G 1.4G 88G 2% / tmpfs 939M 0 939M 0% /dev/shm /dev/sdb1 99G 188M 94G 1% /tmp /dev/sda1 485M 54M 407M 12% /boot My web developer asked me to merge /tmp and / disks so this is what I did: Delete /dev/sdb1 partition using fdisk Create a new partition as LVM on /dev/sdb1 using fdisk Create a new physical volume -- pvcreate /dev/sdb1 Extend volume group -- vgextend /dev/sdb1 vg_test01 Extend logical volume -- lvextend -l +100%FREE /dev/vg_test01/lv_root Resize filesystem -- resize2fs /dev/vg_test01/lv_root This is the new configuration: # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/vg_test01-lv_root 213G 105G 97G 52% / tmpfs 939M 0 939M 0% /dev/shm /dev/sda1 485M 54M 407M 12% /boot /usr/tmpDSK 4.0G 145M 3.6G 4% /tmp Since I have the new settings my web server is throwing kernel panics quite often (around every 2 days). The message says: INFO: task <taskName>:<pid> blocked for more than 120 seconds. The list of process affected that I can see from the console are: mysqld queueprocd httpd suphp vmtoolsd loop0 auditd The only way I can fix this is reseting (cold reboot) the VM. I don't think it is a hardware issue as sar is not showing any bottleneck: Linux 2.6.32-431.3.1.el6.x86_64 (test01) 08/22/2014 _x86_64_ (4 CPU) 12:00:01 AM CPU %user %nice %system %iowait %steal %idle 12:10:01 AM all 26.86 0.01 0.98 0.57 0.00 71.57 12:20:01 AM all 1.78 0.02 1.03 0.08 0.00 97.09 12:30:01 AM all 26.34 0.02 0.85 0.05 0.00 72.74 12:40:01 AM all 27.12 0.01 1.11 1.22 0.00 70.54 12:50:01 AM all 1.59 0.02 0.94 0.13 0.00 97.32 01:00:01 AM all 26.10 0.01 0.77 0.04 0.00 73.07 01:10:01 AM all 27.51 0.01 1.16 0.14 0.00 71.18 01:20:01 AM all 1.80 0.07 1.06 0.08 0.00 96.99 01:30:01 AM all 26.19 0.01 0.78 0.05 0.00 72.96 01:40:01 AM all 26.62 0.02 0.87 0.05 0.00 72.45 01:50:02 AM all 1.35 0.01 0.87 0.02 0.00 97.75 02:00:01 AM all 26.11 0.02 0.69 0.02 0.00 73.17 02:10:01 AM all 26.73 0.02 0.89 0.14 0.00 72.21 02:20:01 AM all 1.45 0.01 0.92 0.04 0.00 97.58 02:30:01 AM all 26.59 0.01 1.06 0.03 0.00 72.31 02:40:01 AM all 26.27 0.01 0.72 0.05 0.00 72.95 02:50:01 AM all 0.86 0.01 0.50 0.09 0.00 98.53 03:00:01 AM all 25.61 0.02 0.39 0.03 0.00 73.96 03:10:01 AM all 26.30 0.08 0.66 0.14 0.00 72.82 03:20:01 AM all 0.81 0.01 0.51 0.04 0.00 98.63 03:30:02 AM all 26.15 0.02 0.53 0.07 0.00 73.24 03:40:01 AM all 26.06 0.01 0.47 0.04 0.00 73.42 03:50:01 AM all 0.96 0.02 0.51 0.03 0.00 98.48 Average: all 17.69 0.02 0.79 0.14 0.00 81.36 06:58:14 AM LINUX RESTART 07:00:01 AM CPU %user %nice %system %iowait %steal %idle 07:10:01 AM all 1.04 0.02 0.57 0.95 0.00 97.42 07:20:02 AM all 0.66 0.01 0.39 0.06 0.00 98.87 07:30:01 AM all 25.71 0.01 0.45 0.16 0.00 73.67 07:40:01 AM all 25.88 0.01 0.35 0.08 0.00 73.68 07:50:01 AM all 1.13 0.02 0.55 0.11 0.00 98.19 As you can see the server became unresponsive at 03.50 AM and I had to reset the VM at 06.58 AM to bring the website up again. I would appreciate any help/assistance to fix this issue. thank you very much

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• Uninstall php and nginx or fix setup

  - by jreed121

  First off, I'm a huge linux noob - sorry... I'm trying to setup nginx with php-fpm on debian and I'm pretty sure that I've completely screwed it up. nginx seems to be running fine because I can it it from a web browser and it load the stock "Welcome to nginx!" page. I'm not so sure about php-fpm though. When I try something like # restart php-fpm I get: bash: restart: command not found First off php-fpm some how got installed as php5-fpm when I do root@server:/etc/init.d# ls, which seems to contradict every tutorial and help doc I've read (supposed to be 'php-fpm'). I can restart it with this: service php5-fpm restart And just enter the package name 'php5-fpm' I get this: root@server:~# php5-fpm [17-Nov-2012 23:15:36] NOTICE: PHP message: PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20100525/suhosin.so' - /usr/lib/php5/20100525/suhosin.so: cannot open shared object file: No such file or directory in Unknown on line 0 [17-Nov-2012 23:15:36] ERROR: An another FPM instance seems to already listen on /var/run/php5-fpm.sock [17-Nov-2012 23:15:36] ERROR: FPM initialization failed The root for nginx is /usr/share/nginx/html, when I try to navigate to a .php file in there with my web browser, it tries to download the file instead of interpret it. I would like this folder to be in my user's home directory ie: /home/administrator/www or /home/nginx/www. I know in order to do this I need to modify nginx.conf, but I find that configuration file difficult to understand. I suppose the fact that my .php scripts aren't being handled is my bigger problem anyways. When I try to see what running on port 9000 (php-fpm default port) with lsof -i :9000 it returns nothing - I guess indicating that it isn't listening. then I head over to vim /etc/php5/fpm/php-fpm.conf and there is no where to designate a port number. So should I just uninstall everything and start from scratch? If so, how do I clean it all up? Any suggestions for a tutorial once I'm ready to try again? Should I attempt to troubleshoot this mess? If so where should I start? Sorry guys, I'm feeling pretty stupid and lost right now. I'm not sure what my next steps are in trying to resolve this issue are. I realize that this is a horrible question for this type of Q&A site, but I'd really appreciate any guidance.

  Read the article

• Trying to setup postfix

  - by Frexuz

  I used this guide: http://jonsview.com/how-to-setup-email-services-on-ubuntu-using-postfix-tlssasl-and-dovecot telnet localhost 25 says 220 episodecalendar.com ESMTP Postfix (Ubuntu) ehlo localhost 250-episodecalendar.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH LOGIN PLAIN 250-AUTH=LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN Installation seems fine? /var/log/mail.log says Nov 26 14:04:06 ubuntu postfix/pickup[12107]: A742E2B9E1: uid=0 from=<root> Nov 26 14:04:06 ubuntu postfix/cleanup[12114]: A742E2B9E1: message-id=<[email protected]> Nov 26 14:04:06 ubuntu postfix/qmgr[12108]: A742E2B9E1: from=<[email protected]>, size=300, nrcpt=1 (queue active) Nov 26 14:04:06 ubuntu postfix/local[12115]: A742E2B9E1: to=<[email protected]>, relay=local, delay=3.3, delays=3.3/0/0/$ Nov 26 14:04:06 ubuntu postfix/cleanup[12114]: AD2662B9E0: message-id=<[email protected]> Nov 26 14:04:06 ubuntu postfix/qmgr[12108]: AD2662B9E0: from=<>, size=2087, nrcpt=1 (queue active) Nov 26 14:04:06 ubuntu postfix/bounce[12117]: A742E2B9E1: sender non-delivery notification: AD2662B9E0 Nov 26 14:04:06 ubuntu postfix/local[12115]: AD2662B9E0: to=<[email protected]>, relay=local, delay=0.02, delays=0.01/0/0/0$ Nov 26 14:04:06 ubuntu postfix/qmgr[12108]: AD2662B9E0: removed Nov 26 14:04:06 ubuntu postfix/qmgr[12108]: A742E2B9E1: removed I'm not really understanding the log file, and obviously I'm not getting any emails. Right now I'm running Ubuntu on a Virtualbox (development box). Is that a problem? The internet connection works fine on it. What about domains etc..? edit: /etc/postfix/main.cf # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file = /etc/postfix/ssl/smtpd.crt smtpd_tls_key_file = /etc/postfix/ssl/smtpd.key smtpd_use_tls = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client.

  Read the article

• Linux Fiber Channel Host Setup Basic

  - by Jim

  I've been googling for about 4 hours now with no luck. I am trying to setup a Linux server running Oracle Server 6.3 as a Fiber Channel host. And then connect it to a Dell Compellent Fibre Channel Host contain a 500GB Volume. The Oracle server itself contains two Brocade 815 FC HBAs. I've discovered their WWN(I think) via cat /sys/class/fc_host/host1/port_name 0x100000051efc3d85 cat /sys/class/fc_host/host2/port_name 0x100000051efc3d9f The next part is where I am at a loss. I've used iSCSI before...is FC the same deal where you have an initiator and a target? If so where do I specific that in linux? I'm also new to Fiber Channel as a protocol, so i am unsure what is needed to make a transaction? WWN and port ID? Similar to IP:Port combination in the Ethernet world. I've read alot regarding using systool, multipath, fc_transport commands, however none of these is recognized as a valid command from Oracle Server 6.3 Appreciate the guidance and assistance. I installed sccsi-target-utils and can now run rescan-scsi-bus and sg_map -x. rescan-scsi-bus.sh -l -w -r Host adapter 0 (megaraid_sas) found. Host adapter 1 ((null)) found. Host adapter 2 ((null)) found. Host adapter 3 (ata_piix) found. Host adapter 4 (ata_piix) found. Scanning SCSI subsystem for new devices and remove devices that have disappeared Scanning host 0 for SCSI target IDs 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15, LUNs 0 1 2 3 4 5 6 7 Scanning for device 0 2 0 0 .... OLD: Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning for device 0 2 1 0 ... OLD: Host: scsi0 Channel: 02 Id: 01 Lun: 00 Vendor: DELL Model: PERC H700 Rev: 2.30 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 1 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 1 0 3 1 ... OLD: Host: scsi1 Channel: 00 Id: 03 Lun: 01 Vendor: COMPELNT Model: Compellent Vol Rev: 0505 Type: Direct-Access ANSI SCSI revision: 05 Scanning host 2 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning host 3 for all SCSI target IDs, LUNs 0 1 2 3 4 5 6 7 Scanning for device 3 0 0 0 ... REM: Host: scsi3 Channel: 00 Id: 00 Lun: 00 DEL: Vendor: TEAC Model: DVD-ROM DV-28SW Rev: R.2A Type: CD-ROM ANSI SCSI revision: 05 Scanning host 4 channels 0 for SCSI target IDs 0, LUNs 0 1 2 3 4 5 6 7 0 new device(s) found. 1 device(s) removed. and sg_map -x /dev/sg0 0 0 32 0 13 /dev/sg1 0 2 0 0 0 /dev/sda /dev/sg2 0 2 1 0 0 /dev/sdb /dev/sg4 1 0 3 1 0 /dev/sdc I'm not sure what this all means...

  Read the article

• "Hostile" network in the company - please comment on a security setup

  - by TomTom

  I have a little specific problem here that I want (need) to solve in a satisfactory way. My company has multiple (IPv4) networks that are controlled by our router sitting in the middle. Typical smaller shop setup. There is now one additional network that has an IP Range OUTSIDE of our control, connected to the internet with another router OUTSIDE of our control. Call it a project network that is part of another companies network and combined via VPN they set up. This means: They control the router that is used for this network and They can reconfigure things so that they can access the machines in this network. The network is physically split on our end through some VLAN capable switches as it covers three locations. At one end there is the router the other company controls. I Need / want to give the machines used in this network access to my company network. In fact, it may be good to make them part of my active directory domain. The people working on those machines are part of my company. BUT - I need to do so without compromising the security of my company network from outside influence. Any sort of router integration using the externally controlled router is out by this idea So, my idea is this: We accept the IPv4 address space and network topology in this network is not under our control. We seek alternatives to integrate those machines into our company network. The 2 concepts I came up with are: Use some sort of VPN - have the machines log into VPN. Thanks to them using modern windows, this could be transparent DirectAccess. This essentially treats the other IP space not different than any restaurant network a laptop of the company goes in. Alternatively - establish IPv6 routing to this ethernet segment. But - and this is a trick - block all IPv6 packets in the switch before they hit the third party controlled router, so that even IF they turn on IPv6 on that thing (not used now, but they could do it) they would get not a single packet. The switch can nicely do that by pulling all IPv6 traffic coming to that port into a separate VLAN (based on ethernet protocol type). Anyone sees a problem with using he switch to isolate the outer from IPv6? Any security hole? It is sad we have to treat this network as hostile - would be a lot easier - but the support personnel there is of "known dubious quality" and the legal side is clear - we can not fulfill our obligations when we integrate them into our company while they are under a jurisdiction we don't have a say in.

  Read the article

• Best RAID setup for multimedia fileserver?

  - by Mr. Schwabe

  I'm building a fileserver for my small office. We do film and multimedia design. Only 3 clients connected. The server is primarily for local access to graphic assets and video files. I'm looking for advice on hardware and software required. Particularly for the RAID. I have the following objectives: A) merged capacity I'd like all other systems to access the data as a single mapped network drive that has an initial capacity of 10 TB. So perhaps 5x 2TB drives (plus mirror drives for redundancy). B) easy way to increase capacity Thinking long term, I'd like to 'easily' add more drives to the array for a potential two or three fold increase in capacity. So theoretically it could get upto a 30 TB raid array consisting of maybe 15x 2 TB drives of capacity (plus mirror drives for redundancy). C) maximum fault tolerance I want at least 1 mirror drive per capacity drive (in laymen's terms). So if I start with 10 TB / 5x 2TB of capacity, I suppose I would need another another 5x 2TB drives to be mirrors. So 10 drives total. But I'd also like potential for even more redundancy; with upto 2 additional mirrors per 'capacity drive' (and to be able to add them to the array anytime with ease). D) easy way to monitor drive health I'd like an intuitive interface for managing the raid and monitoring drive health The other systems accessing this network drive will be running Windows, but also the odd Ubuntu and MacOS system as well. Are these objectives attainable? What type of RAID setup do you recommend? What hardware will be required? Also what OS do you think this system should be running? Does it really matter? I'm no network admin - just a long time Windoze user, without much Linux experience. That said, I'm not opposed to a Linux solution if it's easy enough and more practical than a Windows OS for this server. Or maybe something such as Openfiler. Budget should hit the sweet spot for value and performance (hence my preference to use 2TB drives). The biggest focus is storage; aside from that the system just needs to keep the drives running optimally with perhaps 2 or 3 clients accessing / writing files at any given time. The hardware quote would start with something like 10x 2TB WD Caviar Blacks; about $1900 for the storage + $x for remaining parts. http://ncix.com/products/index.php?sku=42775&vpn=WD2001FASS&manufacture=Western%20Digital%20WD Your advice is appreciated, thanks!

  Read the article

< Previous Page | 43 44 45 46 47 48 49 50 51 52 53 54  | Next Page >