Search Results

Search found 22653 results on 907 pages for 'robert may'.

Page 470/907 | < Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >

  • Why do I get disk I/O errors booting the 3.2 kernel on a xen vps server?

    - by Doug
    I have a xen vps, which I just upgraded to the new LTS 12 Precise Pangolin. However, I see this error on booting: [ 12.848076] end_request: I/O error, dev xvda, sector 12841 [ 12.848093] end_request: I/O error, dev xvda, sector 12841 [ 12.848103] Buffer I/O error on device xvda1, logical block 1605 [ 12.848110] lost page write due to I/O error on xvda1 [ 12.848129] Aborting journal on device xvda1. Results in / being mounted read-only. Reboot: [ 3.087257] EXT3-fs (xvda1): warning: ext3_clear_journal_err: Marking fs in need of filesystem check. [ 3.087677] EXT3-fs (xvda1): recovery complete [ 3.088514] EXT3-fs (xvda1): mounted filesystem with ordered data mode Begin: Running /scripts/local-bottom ... done. done. Begin: Running /scripts/init-bottom ... done. fsck from util-linux 2.20.1 PRGMRDISK1 contains a file system with errors, check forced. Checking disk drives for errors. This may take several minutes. Press C to cancel all checks in progress PRGMRDISK1: ***** REBOOT LINUX ***** PRGMRDISK1: 371152/6001184 files (2.8% non-contiguous), 4727949/12000000 blocks mountall: fsck / [308] terminated with status 3 mountall: System must be rebooted: / [ 151.566949] Restarting system. Name ID Mem VCPUs State Time(s) shadowmint 236 2048 1 --p--- 0.0 Reboot - back to 1. This is definitely an issue with the 3.2 kernel, because booting the 3.0.0 or 2.6.38 kernel series make this issue magically disappear. I'm certain this is some kind of weird xen thing, but no idea. Anyone? Anyhow, until this is resolve I strongly recommend against upgrading if you're running a xen server.

    Read the article

  • how to rewrite or redirect old or missing or invalid url to 404 page

    - by kath
    I recently upgraded a site and almost all URLs have changed. I have redirected all of them (or so I hope) but it may be possible that some of them have slipped by me. Is there a way to somehow catch all invalid URLs and send the user to a certain page I am using PHP Thanks so much! error file is already in .htaccess but seems nothing going to change you can see the error file as below AddHandler application/x-httpd-php5s .php ErrorDocument 404 /content/404.php <IfModule mod_rewrite.c> RewriteEngine on RewriteBase / here are 2 different url one the first one is old one which i edited and the secound one is edited one #1 old one (which is no longer on the server) http://adsbuz.com/vehicles-cars/toyoya/2009-toyota-land-cruiser-gxr-4686.htm #2 the editet one which is on the server http://adsbuz.com/vehicles-cars-for-sale/toyoya/2009-toyota-land-cruiser-gxr-4686.htm i need only the secound one with the vehicles-cars-for-sale because the other directory is already modified and its not on the server but as you can see after the (adsbuz) site name vehicles-cars and vehicles-cars-for-sale both are opening for same location I hope I made myself clear

    Read the article

  • Can domain "masking" be setup in BIND\cPanel

    - by ServerAdminGuy45
    I am supporting a client, let's say he has the domain "acme.com". He registered with GoDaddy and set the name servers to point to his crappy hostgator shared account. He uses cPanel on the hostgator account to set up his subdomains. Is it possible to setup some kind of domain masking so that when someone connects to "application.acme.com", it really forwards to "cloud-solution-provider.com". I mean the actual domain "cloud-solution-provider.com" because it resolves to different IPs based upon geolocation. For this reason I can't just set application.acme.com to point to the IP that cloud-solution-provider.com resolves to. I want the ability for a user to RDP to "application.acme.com" and be sent to the desktop served by "cloud-solution-provider.com", whatever that IP may be. Perhaps I can have GoDaddy be the nameserver? I have a feeling this would break Hostgator since there is a website at acme.com and shop.acme.com

    Read the article

  • Session Evaluations

    - by BuckWoody
    I do a lot of public speaking. I write, teach, present and communicate at many levels. I love to do those things. And I love to get better at them. And one of the ways you get better at something is to get feedback on how you did. That being said, I have to confess that I really despise the “evaluations” I get at most venues. From college to technical events to other locations, at Microsoft and points in between, I find these things to be just shy of damaging, and most certainly useless. And it’s not always your fault. Ouch. That seems harsh. But let me ask you one question – and be as honest as you can with the answer – think about it first: “What is the point of a session evaluation?” I’m not saying there isn’t one. In fact, I think there’s a really important reason for them. In my mind, it’s really this: To make the speaker / next session better. Now, if you look at that, you can see right away that most session evals don’t accomplish this goal – not even a little. No, the way that they are worded and the way you (and I) fill them out, it’s more like the implied goal is this: Tell us how you liked this speaker / session. The current ones are for you, not for the speaker or the next person. It’s a popularity contest. Don’t get me wrong. I want to you have a good time. I want you to learn. I want (desperately, oh, please oh please) for you to like me. But in fact, that’s probably not why you went to the session / took the class / read that post. No, you want to learn, and to learn for a particular reason. Remember, I’m talking about college classes, sessions and other class environments here, not a general public event. Most – OK, all – session evaluations make you answer the second goal, not the first. Let’s see how: First, they don’t ask you why you’re there. They don’t ask you if you’re even qualified to evaluate the session or speaker. They don’t ask you how to make it better or keep it great. They use odd numeric scales that are meaningless. For instance, can someone really tell me the difference between a 100-level session and a 200-level one? Between a 400-level and a 500? Is it “internals” (whatever that means) or detail, or length or code, or what? I once heard a great description: A 100-level session makes me say, “wow - I’m smart.” A 500-level session makes me say “wow – that presenter is smart.” And just what is the difference between a 6 and a 7 answer on this question: How well did the speaker know the material? 1  2  3  4  5  6  7  8  9  10 Oh. My. Gosh. How does that make the next session better, or the speaker? And what criteria did you use to answer? And is a “10” better than a “1” (not always clear, and various cultures answer this differently). When it’s all said and done, a speaker basically finds out one thing from the current session evals: “They liked me. They really really liked me.” Or, “Wow. I think I may need to schedule some counseling for the depression I’m about to go into.” You may not think that’s what the speaker hears, but trust me, they do. Those are the only two reactions to the current feedback sheets they get. Either they keep doing what they are doing, or they get their feelings hurt. They just can’t use the information provided to do better. Sorry, but there it is. Keep in mind I do want your feedback. I want to get better. I want you to get your money and time’s worth, probably as much as any speaker alive. But I want those evaluations to be accurate, specific and actionable. I want to know if you had a good time, sure, but I also want to know if I did the right things, and if not, if I can do something different or better. And so, for your consideration, here is the evaluation form I would LOVE for you to use. Feel free to copy it and mail it to me any time. I’m going to put some questions here, and then I’ll even include why they are there. Notice that the form asks you a subjective question right away, and then makes you explain why. That’s work on your part. Notice also that it separates the room and the coffee and the lights and the LiveMeeting from the presenter. So many presenters are faced with circumstances beyond their control, and yet are rated high or low personally on those things. This form helps tease those apart. It’s not numeric. Numbers are easier for the scoring committees but are useless for you and me. So I don’t have any numbers. We’re actually going to have to read these things, not put them in a machine. Hey, if you put in the work to write stuff down, the least we could do is take the time to read it. It’s not anonymous. If you’ve got something to say, say it, and own up to it. People are not “more honest” when they are anonymous, they are less honest. So put your name on it. In fact – this is radical – I posit that these evaluations should be publicly available. Forever. Just like replies to a blog post. Hey, if I’m an organizer, I would LOVE to be able to have access to specific, actionable information on the attendees and the speakers. So if you want mine to be public, go for it. I’ll take the good and the bad. Enjoy. ------------------------------------------------------------------------------------------------------------------------------------------- Session Evaluation – Date, Time, Location, Topic Thanks for giving us your time today. We know that’s valuable, and we hope you learned something you can use from the session. If you can answer these questions as completely as you can, it will help the next person who attends a session here. Your Name: What you do for a living: (We Need your background to evaluate your evaluation) How long you have been doing that: (Again, we need your background to evaluate your evaluation) Paste Session Description Here: (This is what I said I would talk about) Did you like the session?                     No        Meh        Yes (General subjective question – overall “feeling”. You’ll tell us why in a minute.)  Tell us about the venue. Temperature, lights, coffee, or the online sound, performance, anything other than the speaker and the material. (Helps the logistics to be better or as good for the next person) 1. What did you expect to learn in this session? (How did you interpret that extract – did you have expectations that I should work towards for the next person?) 2. Did you learn what you expected to learn? Why? Be very specific. (This is the most important question there is. It tells us how to make the session better for someone like you.) 3. If you were giving this presentation, would you have done anything differently? What? (Helps us to gauge you, the listener, and might give us a great idea on how to do something better. Thanks!) 4. What will you do with the information you got? (Every presenter wants you to learn, and learn something useful. This will help us do that as well or better)  

    Read the article

  • SharePoint Saturday Huntsville Wrap Up

    - by Mark Rackley
    So, Cathy Dew (@catpaint1) and company put on a great SharePoint Saturday event this past weekend. I got to hang out with some old friends and meet some new ones. I’d list you all, but I’d undoubtedly miss someone and don’t want to offend anyone.  Although I find it odd that I see @MossLover now more since she moved to New Jersey than when she lived next door in Kansas City… what’s up with that? Anyway, Cathy did a tremendous job organizing the event.  Everything went smoothly and everyone had a great time. Maybe I can talk her into organizing the rest of SharePoint Saturday Ozarks on June 12th… you know that’s coming up? right? While you’re here why not go ahead and register right now at: http://spsozarks.eventbrite.com/  Yes.. that was a shameless plug… I did my default presentation on “Wrapping Your Head Around the SharePoint Beast”. This continues to be my most popular presentation. I try to tweak it every time and I always have fun doing it. I get to pick on people and they pick on me back, but I always manage to learn something new when I present it. I had a great interactive crowd and they didn’t throw anything at me.  All in all I consider it a success.  Thanks for coming if you attended!  You can get the slides here:  SharePoint Saturday Huntsville - Wrapping Your Head Around the SharePoint Beast Next up for me is SharePoint Saturday DC on May 15th.  Wow this is going to be a huge event with space for 1500 attendees.. no, that is not a typo!  Stop me and say hi if you are able to make it!!

    Read the article

  • Recent Hotmail Update is crashing FireFox. Is there a fix available

    - by hcabnettek
    I have latest version of FireFox. It has always worked fine using HOTMAIL until recently. I check a checkbox on my items list and FireFox chokes. Thinking back it seems to have started after a recent FireBug update so that may be related. I am liking the older version of Firebug better by the way but thats another post alltogether. Is anyone else having this problem? Is there a fix available? Thanks, ~ck in San Diego

    Read the article

  • Recovering from bad ownership

    - by Christian Sciberras
    I was going to change the ownership of a directory to apache:apache, but I ended up running: chown -R apache:apache / Bad! Very bad! I knew what was going on when it started saying: chown: changing ownership of `/proc/2694/fd/48': Permission denied That's when I stopped everything (Ctrl+C). The current system I have is a server running virtualbox running CentOS 5. This problem happened inside the VM. Currently, everything seems to be working, but I have not restarted the system yet, and to be honest, I'm afraid that if I did something will break. I do not know chown's order, should I be concerned and assume something will break after a reboot? Is there a way to recover form this problem without having to rely on backups? I do have a daily one, but I thought there may be a simpler way out.

    Read the article

  • Distributed Server Monitoring Solution

    - by MaterialEdge
    I belong to an independent IT firm that manages and maintains about 50 business clients networks, ranging from small 5 system networks to 200+ systems. Because we are unable to directly monitor each server at these locations (distributed over a very large area) on a regular basis I am looking for a method to monitor and alert us to any problems that may arise so that we can respond quickly with, hopefully, preventative measures. I'm not sure what solutions are available for this type of situation, but something that utilizes a central server at our business with all client servers sending alerts or logs to it for daily monitoring might work best. All these servers are running a Windows Server OS. In your opinion, what would be the best course of action to accomplish this?

    Read the article

  • Install Base Transaction Error Troubleshooting

    - by LuciaC
    Oracle Installed Base is an item instance life cycle tracking application that facilitates enterprise-wide life cycle item management and tracking capability.In a typical process flow a sales order is created and shipped, this updates Inventory and creates a new item instance in Install Base (IB).  The Inventory update results in a record being placed in the SFM Event Queue.  If the record is successfully processed the IB tables are updated, if there is an error the record is placed in the csi_txn_errors table and the error needs to be resolved so that the IB instance can be created.It's extremely important to be proactive and monitor IB Transaction Errors regularly.  Errors cascade and can build up exponentially if not resolved. Due to this cascade effect, error records need to be considered as a whole and not individually; the root cause of any error needs to be resolved first and this may result in the subsequent errors resolving themselves. Install Base Transaction Error Diagnostic Program In the past the IBtxnerr.sql script was used to diagnose transaction errors, this is now replaced by an enhanced concurrent program version of the script. See the following note for details of how to download, install and run the concurrent program as well as details of how to interpret the results: Doc ID 1501025.1 - Install Base Transaction Error Diagnostic Program  The program provides comprehensive information about the errors found as well as links to known knowledge articles which can help to resolve the specific error. Troubleshooting Watch the replay of the 'EBS CRM: 11i and R12 Transaction Error Troubleshooting - an Overview' webcast or download the presentation PDF (go to Doc ID 1455786.1 and click on 'Archived 2011' tab).  The webcast and PDF include more information, including SQL statements that you can use to identify errors and their sources as well as recommended setup and troubleshooting tips. Refer to these notes for comprehensive information: Doc ID 1275326.1: E-Business Oracle Install Base Product Information Center Doc ID 1289858.1: Install Base Transaction Errors Master Repository Doc ID: 577978.1: Troubleshooting Install Base Errors in the Transaction Errors Processing Form  Don't forget your Install Base Community where you can ask questions to help you resolve your IB transaction errors.

    Read the article

  • Does ZFS cache Compressed or Uncompressed data in a ZFS file-system with compression turned on?

    - by George Bailey
    ZFS supports file-system compression and it also caches frequently or recently accessed data. If a system has lots of CPU but the underlying data storage system is slow. It is possible that ZFS would perform better with compression turned on. This can be easily tested when writing files by measuring CPU and disk usage and throughput. (of course latency may exist,, but this would not be an issue for large files). But what about cache? If data will have to be decompressed every time it is read then this is probably less of a good idea. Is the cached data compressed?. Does anybody have some information on this?

    Read the article

  • FTP upload stalls at same point every time on FileZilla

    - by John
    On two different FTP accounts, I am having problems uploading files. I can login and see the contents of the dir, and start an upload. Using Filezilla the transfer seems to always stall at either 0.9% or 1.2% (always those two numbers) and may simply hang, or keep restarting and then again stop at the same point. WindowsXP FTP is not great but I get similar types of problems there... it starts uploading and after a short while I get a timeout error. FTP used to work fine, and I don't know if it's these accounts in particular (both have the same service provider although purchased on opposite sides of the world) or if "FTP is broken on my PC"... can that even happen?!

    Read the article

  • wireless blocked after installing ubuntu 12.04

    - by Cornelia Frank
    I am using a lenovo S10-3 ideapad; had no problems with earlier version of ubuntu, only since installing 12.04. Have looked through many of the questions on the same issue and tried potential solutions but cannot seem to solve my problem. The hardware switch is in 'on' position and the wireless light comes on very briefly (2-3 sec) when the laptop starts up but then goes off and stays off. Pressing FN+F5 does nothing at all. I'd be grateful for any assistance. Cornelia Have received the following responses in Terminal: cf@cf-Lenovo:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: ideapad_bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: yes cf@cf-Lenovo:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off eth0 no wireless extensions. cf@cf-Lenovo:~$ lshw -C network WARNING: you should run this program as super-user. *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: 00:26:9e:ee:7f:4c size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=10.0.1.8 latency=0 multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0520000-f0520fff memory:f0510000-f051ffff memory:f0540000-f055ffff *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 01 serial: c4:17:fe:f8:bc:d7 width: 64 bits clock: 33MHz capabilities: bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.2.0-31-generic-pae firmware=N/A latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f010ffff WARNING: output may be incomplete or inaccurate, you should run this program as super-user.

    Read the article

  • How can I replicate the look and limitations of the Super NES?

    - by Mikalichov
    I am looking to produce graphics with the same limitations / look that in the Super Nes era. I am specifically looking for graphics similar to Chrono Trigger / FF6. It would be a lot easier to do if I had an idea of the resolution / dpi I am supposed to use. I found that the technical specs for the SNES are: Progressive: 256 × 224, 512 × 224, 256 × 239, 512 × 239 Interlaced: 512 × 448, 512 × 478 But even by using these resolutions, it is pointless if I set it at 72dpi, as I will still have possibly very detailed graphics (that is the main thing, I don't want detailed graphics, I want to go pixelated). I figured it might be related to the sprite size limit, i.e.: Sprites can be 8 × 8, 16 × 16, 32 × 32, or 64 × 64 pixels, each using one of eight 16-color palettes and tiles from one of two blocks of 256 in VRAM. Up to 32 sprites and 34 8 × 8 sprite tiles may appear on any one line. This would work for sprites (characters, objects), but what about maps? Are they built entirely from 8x8 tiles? And then, at what resolution is the end result displayed? It might seem like I am giving the question and answers at the same time, but all of these are suppositions I am making, so could someone confirm or correct them?

    Read the article

  • Mapping Your Customer Experience Journey

    - by Michael Hylton
    For those who attended today’s Oracle Customer Experience Summit keynote you heard from Brian Curran talk about the strategies and best practices to implement customer experience (CX) in your organization.  He spoke about how this evolving journey begins by understanding six steps to transform your business and put your customers front and center.  Here are those key six steps: What are the strategic business objectives in your company? What are your operational objectives and KPIs necessary to measure a CX project? Build an income statement and create “what if” scenarios and see how changes impact your business’ bottom line.  Explore what keeps you from getting to your own goals for your business. Define the business objectives and opportunities you want to meet? Understand the trends and accelerators in the market?  What factors are going on in the market affect that impact your business?  Social?  Mobile?  Cloud?  Just to name a few.  Many of these trends may signal a change in the way people think about your business. What approach will you take to solve these issues?  Understand who your customer is.  How do you need to adapt your business to build relevant, personalized customer experiences. What technologies can you implement to address CX?  Does technology help you solve your problem? A great way to begin your customer experience journey is a concept called journey mapping, one of the most powerful and deceptively simple tools for unlocking CX innovation at your organization. Here is where you can learn more about how you can bring this concept into your business to drive great customer experiences.

    Read the article

  • creating a tag-based website and not using programming?

    - by monodial
    I want to create a tag-based website, and I need a tool that I could use (preferably without programming). It's a site where a user could pick tags on a certain item. All tags will be placed under a group that they are logically linked to (I will do that by hand). On the other end - a visitor could choose a tag, and then be redirected to a few items on which that tag was selected the most. Besides this, I need to set up a registration form (for the visitors who want to select tags on a desired item). stackoverflow.com may serve as an example of what I want to achieve. Functionally it is a quite similar approach. I am not sure if further detailing will bring me closer to getting a development advice, but nevertheless - following this template what I would be missing on is: ability to categorize the tags; and so they would fit in one page (overall i assume <200 tags) box where a user could enter a tag and it would be pending until a certain number of users enter such tag ability to limit the number of 'questions' that appear when a visitor chooses a tag - 'question' stands for an item to which users are selecting tags (displayed items would depend on the frequency the tag was assigned - say the top two items) Which software should I try / How should I go about it? Thank you. Lukas P.S. I have bought hosting account through GoDaddy.com. This is a first website that I am trying to build.

    Read the article

  • Does LINQ require significantly more processing cycles and memory than lower-level data iteration techniques?

    - by Matthew Patrick Cashatt
    Background I am recently in the process of enduring grueling tech interviews for positions that use the .NET stack, some of which include silly questions like this one, and some questions that are more valid. I recently came across an issue that may be valid but I want to check with the community here to be sure. When asked by an interviewer how I would count the frequency of words in a text document and rank the results, I answered that I would Use a stream object put the text file in memory as a string. Split the string into an array on spaces while ignoring punctuation. Use LINQ against the array to .GroupBy() and .Count(), then OrderBy() said count. I got this answer wrong for two reasons: Streaming an entire text file into memory could be disasterous. What if it was an entire encyclopedia? Instead I should stream one block at a time and begin building a hash table. LINQ is too expensive and requires too many processing cycles. I should have built a hash table instead and, for each iteration, only added a word to the hash table if it didn't otherwise exist and then increment it's count. The first reason seems, well, reasonable. But the second gives me more pause. I thought that one of the selling points of LINQ is that it simply abstracts away lower-level operations like hash tables but that, under the veil, it is still the same implementation. Question Aside from a few additional processing cycles to call any abstracted methods, does LINQ require significantly more processing cycles to accomplish a given data iteration task than a lower-level task (such as building a hash table) would?

    Read the article

  • Limiting and redirect port access with useragent

    - by linuxcore
    I'm trying to write iptables string match rule To block http://domain.com:8888 and https://domain.com:8888 when it matches the supplied string in the rule. And another rule to redirect the ports also from 8888 to 7777 I tried following rules but unfortunately didn't work iptables -A INPUT -p tcp -s 0.0.0.0/0 -m string --string linuxcore --algo bm --sport 8888 -j DROP iptables -t raw -A PREROUTING -m string --algo bm --string linuxcore -p tcp -i eth0 --dport 8888 -j DROP iptables -t nat -A PREROUTING -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j REDIRECT --to-port 7777 iptables -A INPUT -t nat -p tcp --dport 8888 -m string --algo bm --string "linuxcore" -j DROP I want to do this from iptables not the webserver because the server may not have a webserver and those ports are working on internal proxy or something like ..etc

    Read the article

  • Photo transfer problems from camera

    - by warkior
    We have a digital camera (Cannon SX130 IS) which we often connect to the Ubuntu 12.10 desktop via USB in order to download the images. In past flavours of Linux (Mint 12 was most recent) it worked fine, however since upgrading to Ubuntu 12.10, the process fails after downloading a small number of the images. I can view the images which will be transferred in the preview window, and I can browse the camera file system to download the images manually, but if I just drag/drop the images over from camera to desktop, it freezes after 5-6 are copied over. I've been able to get around the problem by only copying 3-4 at a time, but when you have 100+ images to transfer, that gets really frustrating. Any advice on where I could start looking for answers, or how I could diagnose the source of the problem further? We have also had some issues with WireLess USB mice though it may not be related. I'm hoping my USB controller in the computer isn't dying... it's not that old. Also, it seems to work much better under Windows.

    Read the article

  • Why not install Msvcr71.dll into system32?

    - by hillu
    While looking for an authoritative source for the missing Msvcr71.dll that is needed by a few old applications, I stumbled across the MSDN article Redistribution of the shared C runtime component in Visual C++. The advice given to developers is to drop the DLL into the application's directory instead of system32 since DLLs in this directory are considered before the system paths. What can/will go wrong if I (as an administrator, not a developer) decide to take the lazy path and install Msvcr71.dll (and Msvcp71.dll while I'm at it) into the system32 directory (of 32 bit Windows XP or Windows 7 systems) instead of putting a copy in each application's directory? Is there another good solution to provide the applications with the needed DLLs that doesn't involve copying stuff to the application directories? added after first answers: I understand that incompatible API changes may have been made to the mentioned DLLs, but pretty much every mention of incompatibilities I have found using Google had to do with games or video codecs. Right now, I expect that the risk of breakage is pretty small. Am I missing something?

    Read the article

  • CPU fan making noise. heat sink or replace...

    - by user32185
    CPU fan is making noise ...i figured out reasons: Cable is hitting the fan causing a vibration. And may be also CPU fan is loose causing vibration... suggest options... i cleaned the fan ...but found that there is no heatsink compound /paste between processor and the fan..is it ok ..should i apply heat sink compound. How to correct the cable vibration... My processor is p4 2.4 ghz motherboard intel 845gvsr if i have to buy new fan ..which brand should i go for ..and estimated cost ?!

    Read the article

  • Force a browser to load the 'https' edition of a website, not the 'http'?

    - by warren
    This is similar to this previous question, but I believe it's a bit different*. Sites like GMail support a preference that pushes all traffic through the SSL edition of the site rather than the plain-text protocol. For sites that don't offer such preferences (or ones that may, but I have been unable to find, like facebook), is there a way using only the browser (perhaps with a plugin or addon) to always try SSL first, and fall-back to plain-text iff SSL fails? Is that solution available on Windows, Mac OS X, and Linux? Just one? * The previous question was looking for external applications that would accomplish this goal.

    Read the article

  • Are these advanced/unfair interview questions regarding Java concurrency?

    - by sparc_spread
    Here are some questions I've recently asked interviewees who say they know Java concurrency: Explain the hazard of "memory visibility" - the way the JVM can reorder certain operations on variables that are unprotected by a monitor and not declared volatile, such that one thread may not see the changes made by another thread. Usually I ask this one by showing code where this hazard is present (e.g. the NoVisibility example in Listing 3.1 from "Java Concurrency in Practice" by Goetz et al) and asking what is wrong. Explain how volatile affects not just the actual variable declared volatile, but also any changes to variables made by a thread before it changes the volatile variable. Why might you use volatile instead of synchronized? Implement a condition variable with wait() and notifyAll(). Explain why you should use notifyAll(). Explain why the condition variable should be tested with a while loop. My question is - are these appropriate or too advanced to ask someone who says they know Java concurrency? And while we're at it, do you think that someone working in Java concurrency should be expected to have an above-average knowledge of Java garbage collection?

    Read the article

  • Gnome 3 - Unable to change date and time

    - by Chris Harris
    I am running Arch Linux with Gnome 3. Unfortunately, although my time and date settings in /etc/rc.conf show that HARDWARECLOCK='UTC' and TIMEZONE='America/LosAngeles'. I continue to get the timezone of Europe/London. If I try to change the date and time via the GUI. It requires root access. After authorizing root access, the date and time may be changed; however, after closing the GUI window, it automatically reverts back to the previous incorrect timezone. I am able to use pool.ntp.org in order to sync my time to the correct one; however, this works only for the current session and is not fixed. This solution is inconvenient since there is not always network access. What other solutions are available for this problem?

    Read the article

  • Which Language Next? Python? Ruby? [closed]

    - by Ryan Craig
    I am a beginning Webmaster (relatively), with 2+ years of php experience. I also have some java training and a bit of .net. My company is now close to redeveloping the website that I work on, which is coded primarily in php, but has some poorly-written .net in part as well (it's confusing and ill-planned, but I didn't make any of those decisions. Can anyone say action-oriented .net and JScript?). So, I'm trying to decide which language I should learn next to quickly develop a new site. I will probably just redevelop it at first in php because I'm very comfortable with it. However, I'd like to migrate in the next year to something newer and more forward-thinking. This being said, .net is out of the question a little bit. We need cheap developers who are fast and can get pages up quickly. In this part of the country, part-time .net developers are hard to find. So, we need something that will be pretty standard in the next few years, but we have some .net SOAP 1.1 APIs that we use on our actual service (separate from the corporate website), that we will need to integrate part of the site with. Developing with php and SOAP is much more difficult than doing the same thing. So, I may have to develop the API collaborative part in .net just to be easy, and then I'd like to use something else that is fast, flexible, forward thinking, and will be relatively standard and easy to find developers for. So, any ideas? Python and Django? Ruby on Rails? Another framework? Thanks for your thoughts. Sorry, I know this was long, but it's all very convoluted and confusing so I needed to be slightly long-winded.

    Read the article

  • In Outlook 2013, the reading pane does not display images correctly for most emails (but does for some)

    - by smoldyr
    I am running Microsoft Office Outlook 2013 on Windows 7 Enterprise. When I click on an email in the list of messages, the preview of the message in the reading pane usually will not show the images contained in the email, but instead will show a red 'X'. Sometimes this red 'X' is followed by the text "The linked image cannot be displayed. The file may have been moved, renmaed, or deleted. Verify that the link points to the correct file and location." I am using an IMAP email account. The really strange thing is that for some emails, the images will display, although they take a long time to load. How can I make the images show up in the reading pane?

    Read the article

< Previous Page | 466 467 468 469 470 471 472 473 474 475 476 477  | Next Page >