Search Results

Search found 21171 results on 847 pages for 'cdo message'.

Page 478/847 | < Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >

• SSD install - what do I need to watch out for when reconfiguring SATA ports?

  - by tim11g

  I installed a Samsung 840 SSD in a Windows 7 machine. It seems to be working fine, but I'm not seeing the expected performance. The AS SSD benchmark gives 76 for read and 138 for write. At the upper left of the benchmark it says "pciide - BAD" and "31K - BAD". I'm assuming the "pciide BAD" means the motherboard (Gigabyte GA-P35-DS4) is configured as IDE emulation and needs to change to native SATA. I don't know what the "31K" refers to. The bios settings look like this: I saw this article that indicates that changing the SATA mode of the boot drive can cause problems (Blue Screen): Error message occurs after you change the SATA mode of the boot drive What is the correct procedure to change the SATA Mode without causing a system failure? Apply the registry change from the MSFT article above first, then reboot and change the SATA mode? Will the SATA mode change in the BIOS affect other drives?

  Read the article

• Very large log files, what should I do?

  - by Masroor

  (This question deals with a similar issue, but it talks about a rotated log file.) Today I got a system message regarding very low /var space. As usual I executed the commands in the line of sudo apt-get clean which improved the scenario only slightly. Then I deleted the rotated log files which again provided very little improvement. Upon examination I find that some log files in the /var/log has grown up to be very huge ones. To be specific, ls -lSh /var/log gives, total 28G -rw-r----- 1 syslog adm 14G Aug 23 21:56 kern.log -rw-r----- 1 syslog adm 14G Aug 23 21:56 syslog -rw-rw-r-- 1 root utmp 390K Aug 23 21:47 wtmp -rw-r--r-- 1 root root 287K Aug 23 21:42 dpkg.log -rw-rw-r-- 1 root utmp 287K Aug 23 20:43 lastlog As we can see, the first two are the offending ones. I am mildly surprised why such large files have not been rotated. So, what should I do? Simply delete these files and then reboot? Or go for some more prudent steps? I am using Ubuntu 14.04.

  Read the article

• Snow Leopard crashes my Xerox printer

  - by Ho Li Cow

  Just set up 2 brand new iMac 21.5" with OS X 10.6.2 pre-installed in our office. Now whenever we try to print an e-mail out, it re-sets the printer i.e. it switches off, does a POST and prints out a Printer Config page. I can print web pages and from other apps fine, just Apple Mail seems to be suffering. Printer is a Xerox Phaser 7750. I downloaded the drivers it recommended when i first tried printing which didn't help and then also tried downloading from the Xerox site. The latter seemed to install fine but then right at the end, it would say 'Installation Successful', then ask me to choose a printer (it found it fine, both by Bonjour and Raw TCP - i tried both) and then it would give an error message. Any help appreciated.

  Read the article

• Is there a framework for describing object oriented communication standards/protocols?

  - by martin

  Currently I'm dealing with the development of specifications for communication standards/protocols for b2b-integration based on object oriented models. I.e. if you take a look at the healthcare domain there is HL7v3 with its HDF. Now I ask if there is a more generic framework, that describes how a specification for a communication standard should be developed. For b2b-integration I want to describe a communication standard based on uml models for a broad domain. My thought was to divide the domain into subdomains and derive message type from the resulting model. There is already a given framework, but I want to compare it to another framework. My idea is to compare them using a generic framework. It should describe several levels. Does anybody know such a framework? I have searched a while on google scholar, but haven't an appropiate framework yet. The only thing I have found is ebXML, but I think it is not exactly what I need.

  Read the article

• Ejabberd Clustering on EC2

  - by Architact

  I am trying to implement ejabberd clustering on Amazon EC2 instances, I have installed ejabberd and it is working fine on both instances, I can connect and send message, my first server is a master server and has the FQDN of master.example.com, second server is a slave and has FQDN of slave.example.com. I have edited the ejabberdctl.cfg file on both instances changed INET_DIST_INTERFACE on both instances to the value returned by ifconfig changed ERLANG_NODE to [email protected] on master and [email protected] on slave. Now when I run this command on slave net_adm:ping('[email protected]'). it always returns pang response indicating that it can't reach the master server. I am looking for possible fixes for that. Things already done Both master and slave domains are pointing to their instances I even tried allocating elastic ip and assigning that to instances, but did not help either. Any help will be greatly appreciated.

  Read the article

• Reporting available RDP sessions

  - by Sergei

  Hi All Default Windows 2003 Server has two RDP sessions available.If all of them are taken by someone else you will only be notified about it after providing your credentials. This seems like a waste of time especially in our environment where we share a lot of development server. Could a message be given as soon as you open the connection window if the connections are taken up? We can use qwinsta based script to check sessions before logon but it's still takes time. Is there a feature to do what I am asking for?

  Read the article

• When send a meeting invite to a specific user, you get a undeliverable response back from another us

  - by jherlitz

  We have a user, where it doesn't matter who sends it, but if you send her a meeting invite through outlook (exchange 2007), you get a non-deliverable message back from another user. Same one all the time though. I checked her shared calendar properties and removed the user from the list. I checked and made sure she wasn't using cache mode. I checked the manage full permissions and send permissions within exchange and the user is not listed. What am I missing? Notes: Using Outlook 2007 with Exchange 2007 on a XP box and Server 2008.

  Read the article

• httpd (no pid file) not running while restarting apache

  - by user59503

  Hi I am working on ubuntu. I got the error messages while try to restart apache. root@XXX:/etc/init.d# sudo /etc/init.d/apache2 restart * Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using xxx.xxx.xx.xxx for ServerName httpd (no pid file) not running apache2: Could not reliably determine the server's fully qualified domain name, using xxx.xxx.xx.xxx for ServerName (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs I got the following message when tried netstat -pant tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 0 32748 9950/httpd tcp 429 0 xxx.xxx.xx.xxx:80 xxx.xxx.xx.xxx:xxxxx CLOSE_WAIT 0 0

  Read the article

• Windows server 2008 R2 nas connection

  - by Msmit1993

  I am a student and i'm experimenting with my own home server running windows server 2008 R2. Now i have a NAS in my network an i can connect with it trough my server but only if i am on the administrator account. My own account is in the administrators group but can't establish a connection with the NAS unless the administrator account has already connected. How do i make my own account connect with the NAS without first connecting with the admin account. The error message on my account: An error occurred while reconnecting Y: to \NAS\Download Microsoft Windows Network: The user name could not be found. This connection has not been restored.

  Read the article

• sendmail on Ubuntu won't send from www-data user

  - by bumperbox

  I if call mail() function in PHP from webserver (running as www-data) i get an error sending email. If i call the same script from the cmdline logged in as root, then it works If i switch user to www-data and run from the cmdline i get this error message WARNING: RunAsUser for MSP ignored, check group ids (egid=33, want=107) can not chdir(/var/spool/mqueue-client/): Permission denied Program mode requires special privileges, e.g., root or TrustedUser. FAILEDWARNING: RunAsUser for MSP ignored, check group ids (egid=33, want=107) can not chdir(/var/spool/mqueue-client/): Permission denied Program mode requires special privileges, e.g., root or TrustedUser. FAILEDTest Complete$ WARNING: RunAsUser for MSP ignored, check group ids (egid=33, want=107) I am guessing i need to do something in sendmail configuration I have googled for some solutions but have ended up more confused. Can someone let me know what configuration I need to change to fix so i can send from www-data user?

  Read the article

• How to re-add RAID-10 dropped drive?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• crippling repeating "pciehp card not present" notifications

  - by Nanne

  When using ubuntu (12.04, both installed and on a live usb) I get a lot of these messages: pciehp 0000:00:1c.5:pcie04: Card not present on Slot(37) pciehp 0000:00:1c.5:pcie04: Card present on Slot(37) And with a lot I mean about 20 per second. This has a crippling effect, and I would like to get rid of it :) The computer is a packard bell easynote BG48-U-100 DC. I tip I picked up from some fedora/redhat error here was to look at lspci -vnn. I have pasted the part about "00:1c.5" here: http://pastebin.com/0sfsiqW2 For what good it may do, here is the lsmod of my machine: http://pastebin.com/DQZy1kAL From that first pastebin I think to conclude that it has to do with the module shpchp, which seems to me (aka: google) to have something to do with ACPI. That's as far as I've come in disecting this. Can anyone help me along further? What can I do, check etc? I did see this topic but my intentions are not to surpress the error message: I know how to do this (from that topic ;) ), but I'm looking for a real sollution. Finding the problem on the internet does suspect me to believe it is neither an ubuntu specific nor a packard-bell specific problem.If you google the problem it seems that is present on several other distribution/hardware combo's as well, and it looks like the advice is to remove one of the drivers? I have no clue as to which driver I should look at and and what would be the effect of just removing it. I have seen this topic which is old-ish, but describes my problem and is about a similar computer. The solution in this topic was to compile a new kernel using a spanish guide, which seems a bit extreme to me, so I'm kinda hoping for a better solution than that.

  Read the article

• Startup error BackgroundContainer.dll on windows 8.1

  - by Manolis Karagiannis

  I have the same problem with this topic! How to resolve BackgroundContainer.dll error on startup? The thing is i did everything that says in answer but i)I found nothing when i started regedit.exe and searched (F3 or CTRL+F) for BackgroundContainer.dll ii)I made a full scan with AntiVirus Scanner like Microsoft Security Essentials/ Defender and also i scaned my PC with Malwarebytes' Anti-Malware,but i found nothing. So this pop up message on start up keep appeared! any idea? Thank you!

  Read the article

• Postfix - Block email from non-existent local addresses

  - by Kelso.b

  My question is very similar to this one, but for postfix. We keep getting emails from addresses like "[email protected]" delivered to other "@ourdomain.com" addresses. From my google research, I understand it might not be practical to verify the email originated from our IP or VPN (Although this would be ideal, so if you can think of a way to do this, let me know), but in most of these cases the sender address (ex. "accounting") is not a valid account. I imagine there must be a way to make sure that a local account exists before delivering the message.

  Read the article

• How to install Tor (Web Browser) in Ubuntu 12.10?

  - by Zignd

  I would like to install the Tor, but I'm having some problems. I know that someone will say "This question is a exactly duplication of How to install tor?", but it's not, because the another question can not be applied to Ubuntu 12.10 as the deb command is not available anymore. I did a research and even at the Tor's Official Website the available resource can not be applied to Ubuntu 12.10. I tried to use the deb command (as the above question says: deb http://deb.torproject.org/torproject.org <DISTRIBUTION> main) and the Terminal says deb: command not found and when I try to install it says E: Unable to locate package deb. I've also tried to use the ppa: ubun-tor, but it's not compatible with Quantal Quetzal, because it's too old. I've also tried to use sudo apt-get install tor, but browser icon don't shows up after installation and if you try to use the command tor in the Terminal I get the following error message: Nov 26 10:59:25.731 [notice] Tor v0.2.3.22-rc (git-4a0c70a817797420) running on Linux. Nov 26 10:59:25.731 [notice] Tor can't help you if you use it wrong! Learn how to be safe at https://www.torproject.org/download/download#warning Nov 26 10:59:25.731 [notice] Read configuration file "/etc/tor/torrc". Nov 26 10:59:25.737 [notice] Initialized libevent version 2.0.19-stable using method epoll (with changelist). Good. Nov 26 10:59:25.737 [notice] Opening Socks listener on 127.0.0.1:9050 Nov 26 10:59:25.737 [warn] Could not bind to 127.0.0.1:9050: Address already in use. Is Tor already running? Nov 26 10:59:25.737 [warn] Failed to parse/validate config: Failed to bind one of the listener ports. Nov 26 10:59:25.737 [err] Reading config failed--see warnings above. Thanks in advance.

  Read the article

• Error loading operating system WinXP Pro

  - by Jakesan

  So im getting the error "Error loading operating system" when the computer tries to boot to a fresh install of WinXP Pro. To get to this point, I: Shrunk the only partition with Gparted to 33GB Copied the partition to the end of the 200GB drive Enlarged the first one to fill the space Formatted the first partition to NTFS Set the first partition to boot, tagged the latter to hidden, removed boot flag This was done all under Hiren's BootCD. Now this is where it goes down the drain. I installed XP Pro SP1a from its CD, and chose to quick format the partition. Now after the OS was installed, I can't start XP without using the default menu action from Hiren's BootCD. All I am greeted with is the "error loading operating system" message. I tried to use the XP recovery to fixboot, fixmbr and bootcfg /rebuild (dont remember if the command was like this, anyway the 3 suggested commands). This did nothing. What am I missing here?

  Read the article

• Can only access asp.net app on localhost

  - by Kevin Donn

  I'm trying to get an asp.net application up on IIS on a Windows Server 2008 machine. I can hit the app from localhost, no problem. But I can't access the app using the server's domain name either locally or from another machine on the network. But here's the odd part. I can access a normal file on IIS using the domain name, both from a browser running on the server and from a browser running on another machine on the network. Here's a synopsis ("http" converted to "htp" below because I don't have enough points to have all these links in my message): From IE on the server itself: works htp://localhost/foo.htm works htp://localhost/App works htp://test.foo.com/foo.htm dead htp://test.foo.com/App From IE on another machine (inside or outside my subnet): works htp://test.foo.com/foo.htm dead htp://test.foo.com/App And when I say "dead" I mean the request times out. Any ideas?

  Read the article

• Qnap won't connect to Windows Share

  - by thetrashcan

  I have a qnap nmp-1000 in my network and would like to stream my films from my win7 laptop to the nmap-1000 device. I just managed to do so with upnp sharing, but I would like to, for security reasons, share my files over a shared folder which is password protected. My problem is when I'm searching for devices on my network with the qnap then it won't find any. When I try to mount a remote disk on my qnap it will just fail with an connection failed message. But when I try to connect to the qnap device with my laptop, it does this succesfully. Can someone guide me through on how to get my setup working?

  Read the article

• can not connect via SSH to a remote Postgresql database

  - by tartox

  I am trying to connect via pgAdmin3 GUI to a Postgresql database on a remote server myHost on port 5432. Server side : I have a Unix myUser that match a postgresql role. pg_hba.conf is : local all all trust host all all 127.0.0.1/32 trust Client side : I open an ssh tunnel : ssh -L 3333:myHost:5432 myUser@myHost I connect to the server via pgAdmin3 ( or via psql -h localhost -p 3333 ). I get the following error message : server closed the connection unexpectedly This probably means the server terminated abnormally before or while processing the request. I have tried to access a specific database with the superuser role using psql -h localhost -p 3333 --dbname=myDB --user=mySuperUser with no more success. What did I forget in the setup ? Thank you

  Read the article

• Hard Drive missing drive space

  - by Chance Robertson

  I have a 500 GB hard drive which I previously attached to my Mac. I detached the drive without going through the eject procedure. When I did this a message showed up, which of course I did not read. I could not use the drive until I formatted again. Now, when I attach the drive it says it is formatted NTFS and has 280.39 of 500 GB free. When I open the drive in Windows Explorer, Finder, or in Linux, is only shows a handful of files totaling 54 MB. How can I find out what is taking up all the space.

  Read the article

• Pandaboard crash on startup or freeze after minutes

  - by Meach

  I just received my Pandaboard ES (rev B) and I am having trouble after installing ubuntu-omap4-addons. Once I copied the image ubuntu-12.04-preinstalled-desktop-armhf+omap4.img on my sd card and boot the pandaboard with it, I run the following commands: sudo add-apt-repository ppa:tiomap-dev/release sudo apt-get update sudo apt-get dist-upgrade sudo apt-get install ubuntu-omap4-extras At the end of the installation of ubuntu-omap4-extras, Ubuntu tells me that a problem occurs when the console displays: ldconfig deferred processing now taking place Clicking on "report the problem" tell me that the problem concerns pvr-omap4-dkms. I read somewhere that this can happen and it is better to reinstall pvr-omap4-dkms. Which I am doing by running: sudo apt-get install --reinstall pvr-omap4-dkms I reboot. Then the board has sometimes difficulties to start Ubuntu: it freezes during the loading page, only action I can do is unplugging the board to start it again. Some other times, Ubuntu load successfully but then freeze at another random time, in the range 20 - 40 minutes. I searched on internet for similar bug and found this: https://bugs.launchpad.net/ubuntu/+source/linux-ti-omap4/+bug/971091 So I typed this in: update-rc.d ondemand disable apt-get -y install cpufrequtils echo 'ENABLE="true" GOVERNOR="performance" MAX_SPEED="0" MIN_SPEED="0"' > /etc/default/cpufrequtils cpufreq-set -r -g performance reboot But it doesn't seems to fix the bug. Another detail: on startup, before the loading screen of Ubuntu (when there is the two penguins displayed :)), it shows this: [0.297271] CPU1: Unknown IPI message 0x1 [0.308990] omap_hwmod: mcpdm: _wait_target_ready error: -16 [0.354705] omap_mux_get_by_name: Could not find signal uart1_cts.uart1_cts [0.354766] omap_hwmod_mux_init: Could not allocate device mux entry [2.107086] thermal_get_slope:Getting slope is not supported for domain gpu [2.107116] thermal_get_offset:Getting offset is not supported for domain gpu [2.107299] stm_fw: vendor driver stm_ti1.0 registered [8.725555] OMAPRPC: Registration of OMAPRPC rpmsg service returned 0! debug=0 Any idea what can be wrong? I am not that good with Ubuntu so any help will be appreciated. Cheers! Meach

  Read the article

• IE9 development tools giving "Unable to attach to the process." error

  - by Urbycoz

  Notice: I have now rebuilt my machine to remove this bug, so I can no longer verify any answers. I recently installed Internet Explorer 9, and activated the development tools by pressing F12; I then clicked "script" and the "start debugging" button but I got the following error: Unable to attach to the process. Another debugger might be attached to the process. I get this message regardless of the site I am on (currently I'm on google.com). I have no other applications running, and have rebooted my machine. Can anyone suggest why this may be appearing?

  Read the article

• How to access a fake raid?

  - by maaartinus

  I have a fake raid, which I wanted to access using mdadm /dev/md0 -A -c 128 -l stripe --verbose /dev/sda /dev/sdc which should be right, as far as I understand the man page. But I get the message mdadm: option -l not valid in assemble mode leaving the offending option out leads to mdadm: failed to create /dev/md0 and (despite verbose) no more information. I'm assuming that -A requires some mdadm-specific header which is obviously missing. I probably need to use "build" instead of assemble, but from the description I'm really unsure whether this is a non-destructive operation. Is it? What should I exactly do? UPDATE I see I haven't made clear, that the array already exists as a fake-raid (I can't give the details about my mainboard now). It looks like doing nothing except for interleaving blocks, so I hoped it could be easily done using mdadm, too. Maybe I'm completely wrong, but all the info I've found was concerned with booting from fake-raid, what I don't really need. I'd be happy with a read access for now.

  Read the article

• How do install Ubuntu from a USB stick?

  - by Sophia

  When I go to the boot menu on my computer and select USB stick, the screen goes black and there comes a flickering underline. Like I could write something. But I can't. Whatever I push, nothing happens. Except the PrintScrn/SysRq button. When I push it, mu computer beeps. I get no choose menu. Nothing. I found out the usb stick is in msdos format. So what format should I use and how can I format it? I am not a computer geek who knows everything. I'm just a beginner. And only 16 years old. I've got a new problem. The screen isn't black anymore. Now there comes an error message: SYSLINUX 4.04 CHS 20110518 Copyright (C) 1994-2011 H.Peter Anvin et al ERROR:No configurationfile found No DEFAULT or UI configuration directive found! boot: And when I write something: boot:example Could not find kernel image:example boot: Why does this fail all the time? ps. I'm using Ubuntu Oneiric 11.10.

  Read the article

• Cannot Enter Repro Admin Web Interface at Port 5080

  - by aqua

  I have followed the instructions on this website www.rtcquickstart.org to set up my firewall, DNS settings, TLS, and have installed the TURN server and repro proxy as instructed, and have restarted repro. However, I am not able to access the web interface of repro on port 5080, either at localhost:5080 / 127.0.0.1:5080 or at the server's IP address: IPADDRESS:5080 (I have set the server's IP for binding in repro.config). I get the browser error message: 'Unable to connect to server' whenever trying to connect to the web interface via port 5080. I initially had Apache2 installed, which loaded pages correctly at port 80 / address root, and when checked it 'listened' at port 5080 after it was configured in /etc/apache2/ports.conf, however the repro web interface still did not work at port 5080. I have tried uninstalling Apache2 in case that was conflicting with repro's web server, but the problem persists, and testing port 5080 now shows that nothing is 'listening' on port 5080. I have tried reinstalling / purging repro but it has not helped. My router is correctly set to allow all ports; port 5080 is open and forwarding correctly. I can connect to the internet and ping all websites through the server and everything else is working correctly. I would be gateful if anyone could offer advice on how to solve this problem.

  Read the article

< Previous Page | 474 475 476 477 478 479 480 481 482 483 484 485  | Next Page >