Search Results

Search found 2036 results on 82 pages for '70 536'.

Page 48/82 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

  • High load average, low CPU and IO (Centos 5.7)

    - by Ben
    A Drupal 7 site with CiviCRM, after running smoothly for a year on a 1&1 VPS suddenly became unresponsive. Now pages eventually load, but can take more than a minute. Looking at resource use in Virtuozzo, the load average carries a warning, and has remained above 1. While I understand this isn't particularly high, this is a change from when the site was working. Here is a typical snapshot of top: top - 03:10:32 up 3:21, 1 user, load average: 1.16, 1.22, 1.30 Tasks: 43 total, 1 running, 42 sleeping, 0 stopped, 0 zombie Cpu(s): 0.1%us, 0.1%sy, 0.1%ni, 99.7%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 2097152k total, 1015112k used, 1082040k free, 0k buffers Swap: 0k total, 0k used, 0k free, 0k cached CPU idle level never seems to go much below 70%. wa is virtually always at 0. There appears to be lots of free memory. And here is some vmstat output, again showign wa at 0, plenty of free memory, and an idle CPU: procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 0 0 1100872 0 0 0 0 2783 23672 0 538 1 0 99 0 0 1 0 0 1100872 0 0 0 0 0 16 0 101754 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 17 0 103133 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 102080 0 0 100 0 0 1 0 0 1100872 0 0 0 0 0 6 0 99881 0 0 100 0 0 0 0 0 1100872 0 0 0 0 0 1 0 105187 0 0 100 0 0 I've spoken to 1&1 but they don't have any ideas as to what could be causing the high load average. Instead they suggested an upgrade :) I've looked for processes that might be causing this, examined MySQL showprocesslist, and restarted the container with no result. Does anyone have more troubleshooting suggestions or insights?

    Read the article

  • Cassandra Remote Connection

    - by Lyuben Todorov
    I'm not managing to connect to cassandra from outside machines. The database is hosted on a windows machine and im trying to connect through a mac (but this shouldn't cause problems) Local connection works: C:\cassandra\bin>cassandra-cli Starting Cassandra Client Connected to: "Test Cluster" on 127.0.0.1/9160 Welcome to Cassandra CLI version 1.1.6 But fails from other machines on the same network bin/cassandra-cli --host 192.168.0.10 --port 9160 org.apache.thrift.transport.TTransportException: java.net.ConnectException: Operation timed out at org.apache.thrift.transport.TSocket.open(TSocket.java:183) at org.apache.thrift.transport.TFramedTransport.open(TFramedTransport.java:81) at org.apache.cassandra.cli.CliMain.connect(CliMain.java:70) at org.apache.cassandra.cli.CliMain.main(CliMain.java:246) Exception connecting to 192.168.0.10/9160. Reason: Operation timed out. Welcome to Cassandra CLI version 1.2.0-beta3 Type 'help;' or '?' for help. Type 'quit;' or 'exit;' to quit. There is a router on the network but these ports have been triggred Ports: 1024, 7000, 7001, 7199, 9160 And the same ports were forwarded to 192.168.0.10 (where Cassandra is hosted) Cassandra version is 1.0.7 And the settings I think i need to change in cassandra.yaml listen_address: 192.168.0.10 rpc_address: I'm not really sure if I've missed any steps. Any help would be appreciated.

    Read the article

  • How do I tell ubuntu to send traffic to a single IP through eth6?

    - by flashnode
    I want to ensure that all IP traffic going to 172.16.60.62 uses eth6. Please provide complete commands because my linux-fu is rusty. The host is running Ubuntu Precise 12.04 user@host:~$ ifconfig eth3 eth3 Link encap:Ethernet HWaddr 00:e0:81:72:fe:c9 inet addr:172.16.60.122 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::2e0:81ff:fe72:fec9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:128500 errors:0 dropped:0 overruns:0 frame:0 TX packets:29082 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:67524823 (67.5 MB) TX bytes:2217634 (2.2 MB) Interrupt:71 Base address:0x6000 user@host:~$ ifconfig eth6 eth6 Link encap:Ethernet HWaddr 00:60:dd:47:81:35 inet addr:172.16.60.61 Bcast:172.16.60.255 Mask:255.255.255.0 inet6 addr: fe80::260:ddff:fe47:8135/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:109610 errors:0 dropped:0 overruns:0 frame:0 TX packets:109388 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:10785630 (10.7 MB) TX bytes:10754350 (10.7 MB) Interrupt:70 user@host:~$ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 172.16.60.1 0.0.0.0 UG 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 1000 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth6 172.16.60.0 0.0.0.0 255.255.255.0 U 1 0 0 eth3

    Read the article

  • Acer Aspire One -- strange battery problem, charges only up to ~90%

    - by houbysoft
    I have this strange problem on the acer aspire one d250. It happened already once before, stayed for about two weeks, and then "fixed itself". The problem is as follows: the battery can't seem to get fully charged; ie the indicator is stuck at about 90% (it's probably not a software problem -- I have ArchLinux and Windows 7 installed and both report exactly the same) and it never passes that value, but it still shows the status as "charging" (I tried everything I could think of -- leaving it charging for extremely long amounts of time, doing a few complete charge-recharge cycles, removing/reinserting the battery, cleaning the connectors, even updating the BIOS, etc., and nothing helped). Also, when it is getting charged, it charges pretty fast until about 70% and then progresses extremely slowly. The battery holds the charge that appears on the battery indicator normally. Just can't get the battery to charge fully -- I can't get it past the 90%. At first I thought this would be a simple battery failure (even if the computer is not that old, about 6-7 months), but as I mentioned it happened once before, and then one day it fixed itself. I tried contacting Acer about this, but the support was not helpful, completely stupid, it seemed like they used canned responses, the usual. Any thoughts on how to fix this?

    Read the article

  • Need help tuning Mysql and linux server

    - by Newtonx
    We have multi-user application (like MailChimp,Constant Contact) . Each of our customers has it's own contact's list (from 5 to 100.000 contacts). Everything is stored in one BIG database (currently 25G). Since we released our product we have the following data history. 5 years of data history : - users/customers (200+) - contacts (40 million records) - campaigns - campaign_deliveries (73.843.764 records) - campaign_queue ( 8 millions currently ) As we get more users and table records increase our system/web app is getting slower and slower . Some queries takes too long to execute . SCHEMA Table contacts --------------------+------------------+------+-----+---------+----------------+ | Field | Type | Null | Key | Default | Extra | +---------------------+------------------+------+-----+---------+----------------+ | contact_id | int(10) unsigned | NO | PRI | NULL | auto_increment | | client_id | int(10) unsigned | YES | | NULL | | | name | varchar(60) | YES | | NULL | | | mail | varchar(60) | YES | MUL | NULL | | | verified | int(1) | YES | | 0 | | | owner | int(10) unsigned | NO | MUL | 0 | | | date_created | date | YES | MUL | NULL | | | geolocation | varchar(100) | YES | | NULL | | | ip | varchar(20) | YES | MUL | NULL | | +---------------------+------------------+------+-----+---------+----------------+ Table campaign_deliveries +---------------+------------------+------+-----+---------+----------------+ | Field | Type | Null | Key | Default | Extra | +---------------+------------------+------+-----+---------+----------------+ | id | int(11) | NO | PRI | NULL | auto_increment | | newsletter_id | int(10) unsigned | NO | MUL | 0 | | | contact_id | int(10) unsigned | NO | MUL | 0 | | | sent_date | date | YES | MUL | NULL | | | sent_time | time | YES | MUL | NULL | | | smtp_server | varchar(20) | YES | | NULL | | | owner | int(5) | YES | MUL | NULL | | | ip | varchar(20) | YES | MUL | NULL | | +---------------+------------------+------+-----+---------+----------------+ Table campaign_queue +---------------+------------------+------+-----+---------+----------------+ | Field | Type | Null | Key | Default | Extra | +---------------+------------------+------+-----+---------+----------------+ | queue_id | int(10) unsigned | NO | PRI | NULL | auto_increment | | newsletter_id | int(10) unsigned | NO | MUL | 0 | | | owner | int(10) unsigned | NO | MUL | 0 | | | date_to_send | date | YES | | NULL | | | contact_id | int(11) | NO | MUL | NULL | | | date_created | date | YES | | NULL | | +---------------+------------------+------+-----+---------+----------------+ Slow queries LOG -------------------------------------------- Query_time: 350 Lock_time: 1 Rows_sent: 1 Rows_examined: 971004 SELECT COUNT(*) as total FROM contacts WHERE (contacts.owner = 70 AND contacts.verified = 1); Query_time: 235 Lock_time: 1 Rows_sent: 1 Rows_examined: 4455209 SELECT COUNT(*) as total FROM contacts WHERE (contacts.owner = 2); How can we optimize it ? Queries should take no more than 30 secs to execute? Can we optimize it and keep all data in one BIG database or should we change app's structure and set one single database to each user ? Thanks

    Read the article

  • Linux udev persistent net rule

    - by Anonymous
    I have a Linux system (Slackware Linux 13.0) with two network interfaces. Let's call them NIC0 and NIC1 My goal is to make NIC0 to appear as eth0 in the system. I know this can be achieved via udev rules that map network aliases to MAC addresses of network interfaces. In Slackware Linux the file /etc/udev/rules.d/70-persistent-net.rules contains such rules. The trickiest part of my problem is that I need to fake the MAC address of NIC0. I know I can dynamically change the MAC addres of a network interface with the command: ifconfig eth0 hw ether <new MAC address> Do you see the problem? This supposes that the network interfaces are already set up. So my question is: If I would have an udev rule for NIC1(the one that shall go up as eth1, with its original MAC address), would it be enough for the system to bring the other network interface (NIC0) as eth0 by default? This way I could change its MAC address later, after the udev machinery completes and the network aliases are brought up.

    Read the article

  • saslauthd using too much memory

    - by Brian Armstrong
    Woke up today to see my site slow/unresponsive. Pulled up top and it looks like a ton of saslauthd processes have spun up using about 64m of RAM each, causing the machine to enter swap space. I've never seen this many used on there. top - 16:54:13 up 85 days, 11:48, 1 user, load average: 0.32, 0.50, 0.38 Tasks: 143 total, 1 running, 142 sleeping, 0 stopped, 0 zombie Cpu(s): 0.7%us, 0.3%sy, 0.0%ni, 97.3%id, 0.2%wa, 0.0%hi, 0.0%si, 1.4%st Mem: 1048796k total, 1025904k used, 22892k free, 14032k buffers Swap: 2097144k total, 332460k used, 1764684k free, 194348k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 848 admin 20 0 263m 115m 4840 S 0 11.3 5:02.91 ruby 906 admin 20 0 265m 113m 4828 S 0 11.1 5:37.24 ruby 30484 admin 20 0 248m 91m 4256 S 6 9.0 219:02.30 delayed_job 4075 root 20 0 160m 65m 952 S 0 6.4 0:24.22 saslauthd 4080 root 20 0 162m 64m 936 S 0 6.3 0:24.48 saslauthd 4079 root 20 0 162m 64m 936 S 0 6.3 0:24.70 saslauthd 4078 root 20 0 164m 63m 936 S 0 6.2 0:24.66 saslauthd 4077 root 20 0 163m 62m 936 S 0 6.1 0:24.66 saslauthd 3718 mysql 20 0 312m 52m 3588 S 1 5.1 3499:40 mysqld 699 root 20 0 72744 7640 2164 S 0 0.7 0:00.50 ruby 15701 postfix 20 0 106m 5712 4164 S 1 0.5 0:00.50 smtpd 15702 postfix 20 0 52444 3252 2452 S 1 0.3 0:00.06 cleanup 4062 postfix 20 0 41884 3104 1788 S 0 0.3 125:26.01 qmgr 15683 root 20 0 51504 2780 2180 S 0 0.3 0:00.04 sshd 14595 postfix 20 0 52308 2548 2304 S 1 0.2 0:24.60 proxymap 15483 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.38 smtp 15486 postfix 20 0 43380 2544 1992 S 0 0.2 0:00.36 smtp 15488 postfix 20 0 43380 2540 1992 S 0 0.2 0:00.38 smtp 15485 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.36 smtp 15489 postfix 20 0 43380 2532 1984 S 0 0.2 0:00.40 smtp Wasn't sure what Saslauthd is, Google says it handles plantext authentication. The machine has been sending a lot of email through postfix, so this could be related. Anyone know why so many may have spun up? Are they safe to kill? Thanks!

    Read the article

  • Poor gaming performance with hyper-v installed in windows 8

    - by SnowCrash
    I am getting very poor gaming performance on my Windows 8 host OS with Hyper-V installed but no guest machines running. For example World of Tanks reports 60-70 FPS without Hyper-V installed and 4-14 FPS with it installed. A similar, dramatic, hit is observed in several other games so the issue is not WoT specific. To make the point clear, I am not trying to run games in a virtual machine. I don't even have a VM running while observing this effect. I simply have the Hyper-V feature installed. My system specs: AMD Phenom II 965 (3.4 GHz) AMD Radeon 6950 2GB (XFX Double D HD-695X-CDFC) 16GB DDR3 1333 AMD 790GX chipset Mainboard (Gigabyte GA-MA790GPT-UD3H) I have tried every AMD driver from 12.8 to the current 12.11beta8, virtualization is enabled in the BIOS settings, the onboard 3300HD video device is disabled in BIOS and I have read the MSDN blog entry here regarding a similar issue in Server 2008 that was resolved in 2008 R2 (and hopefully not regressed in Win 8). I'd like to be able to use Hyper-V for development and testing at home (I am a sysadmin/software developer professionally). If, however, I can't also use my home system for entertainment I'll have to scrap those plans.

    Read the article

  • How do I troubleshoot a slow hard drive?

    - by Bruce Connor
    My computer is suffering of slow-downs and I'm not surprised (it's around 6 years old). Here's what I've verified: They are not very frequent (only a couple of times a day). When they happen a single application will hang for 10-60 seconds, while the rest don't hang but also get slow. Even as it is happening, the CPU usage stays low. It happens to applications (such as text editor, firefox, skype). It never happens to some applications (such as games) which I use for hours under heavy CPU load. Also of note: The Graphics card and PSU are new (around a year). Though I have a decent amount of software installed right now, this was happening even right after I reinstalled Windows. This HDD has been through many partinioning schemes, and a few heavy operations (such as moving around 200GB of data). Because of the above, I am already 70% sure the problem is with the hard drive. Before I replace it, however, I want to rule out other less likely possibilities (such as RAM, software, or PSU). I don't have the money to replace the entire box right now, but I can easily replace one of the components. I've read several questions (such as this one) which give general guidance on troubleshooting an unknown issue, that is not what I'm looking for here. My main question is: What tests or benchmarks can I run to verify I have a problematic hard drive? I don't need to solve this problem, I am content with just making sure it's the hard drive. I could borrow a newer hard drive from a friend and see if it gets better. A positive result would rule out all other components, but it wouldn't rule out a software issue (since this new hard drive won't have any of the software I use daily). Running on Windows/Linux.

    Read the article

  • Request bursting from web application Load Tests

    - by MaseBase
    I'm migrating our web and database hosting to a new environment on all new machines. I've recently performed a Load Test using WAPT to generate load from multiple distributed clients. The server has plenty of room to handle the traffic load, but I'm seeing an odd pattern of incoming traffic during the load tests. Here is the gist of our setup: Firewall server running MS Forefront TMG 2010 on Win 2k8 server Request routing done by IIS Application Request Routing on firewall machine Web server is a Hyper-V VM on the Database server (which is the host OS) These machines are hefty with dual-CPU's with six cores (12 total procs) Web server running IIS 7.5 Web applications built in ASP.NET 2.0, with 1 ISAPI filter (Url Rewrite) in front What I'm seeing during the load tests is that the requests all come through in bursts. Even though I have 7 different distributed clients sending traffic loads, the requests come through about 300-500 requests at a time. The performance monitor shows nearly all of the counters moving through this pattern, where a burst of requests comes in the req/sec jumps to 70, the queued requests jumps to 500, the current requests jumps up, the CPU jumps up, everything. Then once it's handled that group of requests, it has a lull for nearly 10 seconds where nearly nothing is happening. 0-5 req/sec, 0 queued requests, minimal CPU usage. Then after 10 seconds of inactivity, another burst comes through, spiking all of the counters once again. What I can't figure out is why the requests are coming through in bursts when I know that the load being generated is not sent that way, especially considering the various load-generating clients sending traffic all in different intervals with random think time's between each request. Is there something in the layers between Hyper-V or perhaps in the hardware which might cause this coalesce of requests together? Here is what i'm looking at, the highlighted metric is Requests/sec, but the others critical counter go with it: Requests Queued (which I'd obviously like to keep as close to 0 as possible). Any ideas on this?

    Read the article

  • Tomcat web application intermittent freeze

    - by tinny
    I have a Grails web application (just a standard war file) deployed on a Ubuntu 10.10 server running on tomcat 6. My database is postgresql. The problem is that every so often (once or twice a day after inactivity) when I try to log into this web application it just freezes. I can navigate to the login page but when I try and login (first time the DB is hit, might be a clue..?) the application just freezes indefinitely, no 500 response code... the browser just waits and waits. I followed the instructions detailed here because the problem described sounded the same as mine. My GC logging showed no long running GC, all sub sec. When the application freezes a jmap heap output is... using parallel threads in the new generation. using thread-local object allocation. Concurrent Mark-Sweep GC Heap Configuration: MinHeapFreeRatio = 40 MaxHeapFreeRatio = 70 MaxHeapSize = 536870912 (512.0MB) NewSize = 21757952 (20.75MB) MaxNewSize = 87228416 (83.1875MB) OldSize = 65404928 (62.375MB) NewRatio = 7 SurvivorRatio = 8 PermSize = 21757952 (20.75MB) MaxPermSize = 85983232 (82.0MB) Heap Usage: New Generation (Eden + 1 Survivor Space): capacity = 19595264 (18.6875MB) used = 11411976 (10.883308410644531MB) free = 8183288 (7.804191589355469MB) 58.23843965562291% used Eden Space: capacity = 17432576 (16.625MB) used = 9249296 (8.820816040039062MB) free = 8183280 (7.8041839599609375MB) 53.05754009046053% used From Space: capacity = 2162688 (2.0625MB) used = 2162680 (2.0624923706054688MB) free = 8 (7.62939453125E-6MB) 99.99963008996212% used To Space: capacity = 2162688 (2.0625MB) used = 0 (0.0MB) free = 2162688 (2.0625MB) 0.0% used concurrent mark-sweep generation: capacity = 101556224 (96.8515625MB) used = 83906080 (80.01907348632812MB) free = 17650144 (16.832489013671875MB) 82.62032270912317% used Perm Generation: capacity = 85983232 (82.0MB) used = 62866832 (59.95448303222656MB) free = 23116400 (22.045516967773438MB) 73.1152232100324% used Anyone know what "From Space:" is? Any ideas on further fault finding ideas? I dont have much experience with this type of fault finding.

    Read the article

  • Overriding routes on Openvpn client, iproute, iptables2

    - by sarvavijJana
    I am looking for some way to route packets based on its destination ports switching regular internet connection and established openvpn tunnel. This is my configuration OpenVPN server ( I have no control over it ) OpenVPN client running ubuntu wlan0 192.168.1.111 - internet connected if Several routes applied on connection to openvpn from server: /sbin/route add -net 207.126.92.3 netmask 255.255.255.255 gw 192.168.1.1 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 5.5.0.1 And I need to route packets regarding it's destination ports for ex: 80,443 into vpn everything else directly to isp connection 192.168.1.1 What i have used during my attempts: iptables -A OUTPUT -t mangle -p tcp -m multiport ! --dports 80,443 -j MARK --set-xmark 0x1/0xffffffff ip rule add fwmark 0x1 table 100 ip route add default via 192.168.1.1 table 100 I was trying to apply this settings using up/down options of openvpn client configuration All my attempts reduced to successful packet delivery and response only via vpn tunnel. Packets routed bypassing vpn i have used some SNAT to gain proper src address iptables -A POSTROUTING -t nat -o $IF -p tcp -m multiport --dports 80,443 -j SNAT --to $IF_IP failed in SYN-ACK like 0 0,1 0,1: "70","192.168.1.111","X.X.X.X","TCP","34314 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18664016 TSER=0 WS=7" "71","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584430 TSER=18654692 WS=5" "72","X.X.X.X","192.168.1.111","TCP","81 > 34314 [SYN, ACK] Seq=0 Ack=1 Win=5792 Len=0 MSS=1428 TSV=531584779 TSER=18654692 WS=5" "73","192.168.1.111","X.X.X.X","TCP","34343 > 81 [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=18673732 TSER=0 WS=7" I hope someone has already overcome such a situation or probably knows better approach to fulfill requirements. Please kindly give me a good advice or working solution.

    Read the article

  • Very poor SCSI hd performance on IBM x336 with LSI 1030 RAID1

    - by David Tschoepe
    I'm experiencing very poor performance on an IBM x336 server with dual 73GB 15k hard drives on a U320 controller, LSI 1030. We're getting maybe 3.5MB/sec max (per HD Tune utility). It should be over 100MB/sec at least, I would think (another x335 box is running 70-80MB/sec). The server was recently setup and didn't really notice the problem, but may have been there from the beginning, so not sure. I have installed the IBM ServerRAID Windows utility. The server is running Windows 2008 R2 Web edition (if that matters). I thought maybe one of the drives was bad, so far I have removed one of the drives out of the array and tested again, but still the same results. I'm waiting for the RAID1 to resync and I will try pulling the other drive next. I've also used the ServerRAID utility but haven't noticed anything in there that might indicate a problem. Not sure if I'm on the right path here. So looking for some advice to track this down.

    Read the article

  • Is basing storage requirements based on IOPS sufficient?

    - by Boden
    The current system in question is running SBS 2003, and is going to be migrated on new hardware to SBS 2008. Currently I'm seeing on average 200-300 disk transfers per second total across all the arrays in the system. The array seeing the bulk of activity is a 6 disk 7200RPM RAID 6 and it struggles to keep up during high traffic times (idle time often only 10-20%; response times peaking 20-50+ ms). Based on some rough calculations this makes sense (avg ~245 IOPS on this array at 70/30 read to write ratio). I'm considering using a much simpler disk configuration using a single RAID 10 array of 10K disks. Using the same parameters for my calculations above, I'm getting 583 average random IOPS / sec. Granted SBS 2008 is not the same beast as 2003, but I'd like to make the assumption that it'll be similar in terms of disk performance, if not better (Exchange 2007 is easier on the disk and there's no ISA server). Am I correct in believing that the proposed system will be sufficient in terms of performance, or am I missing something? I've read so much about recommended disk configurations for various products like Exchange, and they often mention things like dedicating spindles to logs, etc. I understand the reasoning behind this, but if I've got more than enough random I/O overhead, does it really matter? I've always at the very least had separate spindles for the OS, but I could really reduce cost and complexity if I just had a single, good performing array. So as not to make you guys do my job for me, the generic version of this question is: if I have a projected IOPS figure for a new system, is it sufficient to use this value alone to spec the storage, ignoring "best practice" configurations? (given similar technology, not going from DAS to SAN or anything)

    Read the article

  • Mysql, SSL and java client problem

    - by CarlosH
    I'm trying to connect to an SSL-enabled mysql server from my own java application. After setting up ssl on mysqld, and successfuly tested an account using "REQUIRE ISSUER and SUBJECT", I wanted to use that account in a java app. I've generated a private key (to a file called keystore.jks) and csr using keytool, and signed the csr using my own CA(The same used with mysqld and its certificate). Once signed the csr, I've imported the CA and client cert into the keystore.jks file. When running the application the SSL connection can't be established. Relevant logs: ... [Raw read]: length = 5 0000: 16 00 00 02 FF ..... main, handling exception: javax.net.ssl.SSLException: Unsupported record version Unknown-0.0 main, SEND TLSv1 ALERT: fatal, description = unexpected_message Padded plaintext before ENCRYPTION: len = 32 0000: 02 0A BE 0F AD 64 0E 9A 32 3B FE 76 EF 40 A4 C9 .....d..2;.v.@.. 0010: B4 A7 F3 25 E7 E5 09 09 09 09 09 09 09 09 09 09 ...%............ main, WRITE: TLSv1 Alert, length = 32 [Raw write]: length = 37 0000: 15 03 01 00 20 AB 41 9E 37 F4 B8 44 A7 FD 91 B1 .... .A.7..D.... 0010: 75 5A 42 C6 70 BF D4 DC EC 83 01 0C CF 64 C7 36 uZB.p........d.6 0020: 2F 69 EC D2 7F /i... main, called closeSocket() main, called close() main, called closeInternal(true) main, called close() main, called closeInternal(true) connection error com.mysql.jdbc.exceptions.jdbc4.CommunicationsException: Communications link failure Any idea why is this happening?

    Read the article

  • Huge host CPU usage in idle vmware guest. Ubuntu 10.04 host, Vista SP2 guest

    - by themesandmodules
    I'm experiencing huge host CPU usage with an idle vmware guest. Host: Ubuntu 10.04 32-bit 2.6.32-24-generic-pae. (Very new install, i.e 24 hours ago) Hardware is Dell XPS M1530 laptop, 4GB ram. Intel Core II Duo T9300 2.50Ghz The virtualization setting "VT" or something is enabled in my bios. Guest: Completely fresh install of Windows Vista, upgraded to latest SP2 and all windows updates installed. 1024 - 1512MB ram allocated. Absolutely no other software installed on it, apart from VMWare tools. Situation When the guest is doing absolutely nothing, I watch with sysinternals process watch on the guest. This shows that system idle process is between 70 and 99%, usually around 95%. No actual process doing anything. On the host, I watch with top, I get cpu usage of 20% - 80%, usually around 30%. What I have tried Single and Dual processor available to guest - no change. Turn off all peripherals to guest - no network, drives, usb etc - no change. Turn off 3d acceleration for guest - perhaps a small improvement, or no change. Upping allocated ram to guest from 1024MB to 1512MB - no change. Yelling at vmware - no change. I have experienced a similar issue in the past, which was solved by setting the guest to have 1 CPU. This time that hasn't worked.

    Read the article

  • Best practice for Exchange 2010 HA topology considering 6 x Exchange licenses and TMG 2010

    - by MadBoy
    What would be best topology considering that: 6 x Exchange 2010 Standard Licenses 2 x Separate locations that are supposed to support redundancy in case of link problems 4 x Forefront TMG 2010 with Forefront Security and Forefront Protection/Security Multiple locations worldwide using those Exchange. Most locations will be connected with VPN Tunnel (the ones hosting Exchange for sure). I was thinking something like this: Location MAIN (about 70-100 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Location SUPPORT (about 20 people): 2x TMG 2010 in NLB 1x Exchange 2010 CAS/HUB Role 2x Exchange 2010 Mailbox Role (Active + Passive) Management wants to make sure that in case of problems in main location (power failure, link loss etc) second location can support all traffic from around the world and vice-versa. We have 6-7 locations and more comming up (not big ones but like 10+ people per each location). I do know that CAS/HUB is single point of failure (and no NLB), but i simply lack more licenses to do some redundancy on that. What do you think about this approach? What would be better approach according to you?

    Read the article

  • configure Squid3 proxy server on Ubuntu with caching and logging

    - by Panshul
    I have a ubuntu 11.10 machine. Installed Squid3. When i configure the squid as http_access allow all, everything works fine. my current configuration mostly default is as follows: 2012/09/10 13:19:57| Processing Configuration File: /etc/squid3/squid.conf (depth 0) 2012/09/10 13:19:57| Processing: acl manager proto cache_object 2012/09/10 13:19:57| Processing: acl localhost src 127.0.0.1/32 ::1 2012/09/10 13:19:57| Processing: acl to_localhost dst 127.0.0.0/8 0.0.0.0/32 ::1 2012/09/10 13:19:57| Processing: acl SSL_ports port 443 2012/09/10 13:19:57| Processing: acl Safe_ports port 80 # http 2012/09/10 13:19:57| Processing: acl Safe_ports port 21 # ftp 2012/09/10 13:19:57| Processing: acl Safe_ports port 443 # https 2012/09/10 13:19:57| Processing: acl Safe_ports port 70 # gopher 2012/09/10 13:19:57| Processing: acl Safe_ports port 210 # wais 2012/09/10 13:19:57| Processing: acl Safe_ports port 1025-65535 # unregistered ports 2012/09/10 13:19:57| Processing: acl Safe_ports port 280 # http-mgmt 2012/09/10 13:19:57| Processing: acl Safe_ports port 488 # gss-http 2012/09/10 13:19:57| Processing: acl Safe_ports port 591 # filemaker 2012/09/10 13:19:57| Processing: acl Safe_ports port 777 # multiling http 2012/09/10 13:19:57| Processing: acl CONNECT method CONNECT 2012/09/10 13:19:57| Processing: http_access allow manager localhost 2012/09/10 13:19:57| Processing: http_access deny manager 2012/09/10 13:19:57| Processing: http_access deny !Safe_ports 2012/09/10 13:19:57| Processing: http_access deny CONNECT !SSL_ports 2012/09/10 13:19:57| Processing: http_access allow localhost 2012/09/10 13:19:57| Processing: http_access deny all 2012/09/10 13:19:57| Processing: http_port 3128 2012/09/10 13:19:57| Processing: coredump_dir /var/spool/squid3 2012/09/10 13:19:57| Processing: refresh_pattern ^ftp: 1440 20% 10080 2012/09/10 13:19:57| Processing: refresh_pattern ^gopher: 1440 0% 1440 2012/09/10 13:19:57| Processing: refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 2012/09/10 13:19:57| Processing: refresh_pattern (Release|Packages(.gz)*)$ 0 20% 2880 2012/09/10 13:19:57| Processing: refresh_pattern . 0 20% 4320 2012/09/10 13:19:57| Processing: http_access allow all 2012/09/10 13:19:57| Processing: cache_mem 512 MB 2012/09/10 13:19:57| Processing: logformat squid3 %ts.%03tu %6tr %>a %Ss/%03>Hs %<st %rm %ru 2012/09/10 13:19:57| Processing: access_log /home/panshul/squidCache/log/access.log squid3 The problem starts when I enable the following line: access_log /home/panshul/squidCache/log/access.log I start to get proxy server is refusing connections error in the browser. on commenting out the above line in my config, things go back to normal. The second problem starts when i add the following line to my config: cache_dir ufs /home/panshul/squidCache/cache 100 16 256 The squid server fails to start. Any suggestions what am I missing in the config. Please help.!!

    Read the article

  • Unable to get squid working for remote users

    - by Sean
    I am trying to setup squid 3.2.4, but I have not been able to get it working for remote users. Works fine locally. Unable to figure out what I am doing wrong... http_port 3128 transparent ssl-bump generate-host-certificates=on dynamic_cert_mem_cache_size=4MB cert=/usr/share/ssl-cert/myCA.pem refresh_pattern ^ftp: 1440 20% 10080 refresh_pattern ^gopher: 1440 0% 1440 refresh_pattern -i (/cgi-bin/|\?) 0 0% 0 refresh_pattern . 0 20% 4320 acl localnet src 10.0.0.0/8 # RFC 1918 possible internal network acl localnet src 172.16.0.0/12 # RFC 1918 possible internal network acl localnet src 192.168.0.0/16 # RFC 1918 possible internal network acl localnet src fc00::/7 # RFC 4193 local private network range acl localnet src fe80::/10 # RFC 4291 link-local (directly plugged) machines acl SSL_ports port 443 acl Safe_ports port 80 # http acl Safe_ports port 21 # ftp acl Safe_ports port 443 # https acl Safe_ports port 70 # gopher acl Safe_ports port 210 # wais acl Safe_ports port 1025-65535 # unregistered ports acl Safe_ports port 280 # http-mgmt acl Safe_ports port 488 # gss-http acl Safe_ports port 591 # filemaker acl Safe_ports port 777 # multiling http acl CONNECT method CONNECT http_access allow manager localhost http_access deny manager http_access deny !Safe_ports http_access allow localhost http_access allow localnet http_access allow all cache deny all via off forwarded_for off header_access From deny all header_access Server deny all header_access WWW-Authenticate deny all header_access Link deny all header_access Cache-Control deny all header_access Proxy-Connection deny all header_access X-Cache deny all header_access X-Cache-Lookup deny all header_access Via deny all header_access Forwarded-For deny all header_access X-Forwarded-For deny all header_access Pragma deny all header_access Keep-Alive deny all acl ip1 localip 1.1.1.90 acl ip2 localip 1.1.1.91 acl ip3 localip 1.1.1.92 acl ip4 localip 1.1.1.93 acl ip5 localip 1.1.1.94 tcp_outgoing_address 1.1.1.90 ip1 tcp_outgoing_address 1.1.1.91 ip2 tcp_outgoing_address 1.1.1.92 ip3 tcp_outgoing_address 1.1.1.93 ip4 tcp_outgoing_address 1.1.1.94 ip5 tcp_outgoing_address 1.1.1.90

    Read the article

  • linux mint VIA sound issue

    - by user2699451
    So I installed linux Mint 15 "Olivia" 64 bit on my Mecer W550EU laptop I have HD Audio with a VIA chipset charles-W55xEU charles # lsmod | grep snd snd_hda_codec_hdmi 36913 1 snd_hda_codec_via 51018 1 snd_hda_intel 39619 5 snd_hda_codec 136453 3 snd_hda_codec_hdmi,snd_hda_codec_via,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 97451 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 snd_seq_midi_event 14899 1 snd_seq_midi snd_rawmidi 30180 1 snd_seq_midi snd_seq 61554 2 snd_seq_midi_event,snd_seq_midi snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi snd_timer 29425 2 snd_pcm,snd_seq snd 68876 19 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_via,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device soundcore 12680 1 snd And my sound card charles-W55xEU charles # aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: VT1802 Analog [VT1802 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 2: VT1802 HP [VT1802 HP] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 and my audio device charles-W55xEU charles # lspci -v | grep -A7 -i "audio" 00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High `Definition Audio Controller (rev 04)` Subsystem: CLEVO/KAPOK Computer Device 0550 Flags: bus master, fast devsel, latency 0, IRQ 47 Memory at f7c10000 (64-bit, non-prefetchable) [size=16K] Capabilities: [50] Power Management version 2 Capabilities: [60] MSI: Enable+ Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00 Capabilities: [100] Virtual Channel Sometimes when I boot up, soundworks, other times it doenst, it is completely random, so far, no-one on xchat linux help or linux mint forums was able to help me, I have always had issues with sound on VIA chipsets I have: sudo apt-get upgrade && apt-get install mint-meta-cinnamon it seemed to help but after 2-3 reboots, the problem came back, btw, everytime I checked, pulse audio is selected to Duplex Audio Input & Output and alsa mixer is always unmuted!

    Read the article

  • What is the fastest way to resize a large partition?

    - by Jook
    Due to a new HDD-Configuration I am currently handling larger backup/resize tasks with partitions between around 900MB, wich are 70-90% full. some background: First thing I've noticed was, that the Acronis-WesternDigital TrueImage was extremly slow while running it under Windows 7, even though on high priority. To create a normal backup for 650gb of data (900gb partition), it would have taken 3 days! The same task done with the boot-cd version of this acronis version took about 2 hours (SATA3 copy from one disk to another, both around 110MB/s). Now, after I have done all my backups, I've wanted to remove some obsolete partitions and resize the leftovers to full hdd size. Of course, usually this takes quite some time - in this case for this 900gb partition, to extend it to 931 (30gb+ from front, 1gb+ from end), it will take around 6 hours (using gparted)! Had I new that erlier, I would have just restored the image. But no - first it showed a reasonable time of 1:45h and 0 of 1 operations, but after finishing 1:45h it started again, only this time with 4h to go, still 0 of 1 operations, but now it was copying instead of moving. Question: However, why has it to be this slow to resize a partition? I am asking for a good explanaition. This has bugged me, since I started partitioning - why does it require to copy all the data around, can't it just stay in place?!

    Read the article

  • Server load high, CPU idle. NFS the cause?

    - by Mech Software
    I am running into a scenario where I'm seeing a high server load (sometimes upwards of 20 or 30) and a very low CPU usage (98% idle). I'm wondering if these wait states are coming as part of an NFS filesystem connection. Here is what I see in VMStat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 1 0 1298784 0 0 0 0 16 5 0 9 1 1 97 2 0 0 1 0 1308016 0 0 0 0 0 0 0 3882 4 3 80 13 0 0 1 0 1307960 0 0 0 0 120 0 0 2960 0 0 88 12 0 0 1 0 1295868 0 0 0 0 4 0 0 4235 1 2 84 13 0 6 0 0 1292740 0 0 0 0 0 0 0 5003 1 1 98 0 0 4 0 0 1300860 0 0 0 0 0 120 0 11194 4 3 93 0 0 4 1 0 1304576 0 0 0 0 240 0 0 11259 4 3 88 6 0 3 1 0 1298952 0 0 0 0 0 0 0 9268 7 5 70 19 0 3 1 0 1303740 0 0 0 0 88 8 0 8088 4 3 81 13 0 5 0 0 1304052 0 0 0 0 0 0 0 6348 4 4 93 0 0 0 0 0 1307952 0 0 0 0 0 0 0 7366 5 4 91 0 0 0 0 0 1307744 0 0 0 0 0 0 0 3201 0 0 100 0 0 4 0 0 1294644 0 0 0 0 0 0 0 5514 1 2 97 0 0 3 0 0 1301272 0 0 0 0 0 0 0 11508 4 3 93 0 0 3 0 0 1307788 0 0 0 0 0 0 0 11822 5 3 92 0 0 From what I can tell when the IO goes up the waits go up. Could NFS be the cause here or should I be worried about something else? This is a VPS box on a fiber channel SAN. I'd think the bottleneck wouldn't be the SAN. Comments?

    Read the article

  • Will adding a SSD cache device to my ZFS storage improve performance?

    - by Sysadminicus
    The server has 4GB of RAM and my zpool is made up of 15.5k SAS drives arranged like this: NAME STATE READ WRITE CKSUM tank ONLINE 0 0 0 raidz1-0 ONLINE 0 0 0 c0t2d0 ONLINE 0 0 0 c0t3d0 ONLINE 0 0 0 c0t4d0 ONLINE 0 0 0 c0t5d0 ONLINE 0 0 0 c0t6d0 ONLINE 0 0 0 c0t7d0 ONLINE 0 0 0 c0t8d0 ONLINE 0 0 0 raidz1-1 ONLINE 0 0 0 c0t10d0 ONLINE 0 0 0 c0t11d0 ONLINE 0 0 0 c0t12d0 ONLINE 0 0 0 c0t13d0 ONLINE 0 0 0 c0t14d0 ONLINE 0 0 0 spares c0t9d0 AVAIL c0t1d0 AVAIL The primary use is as an NFS store for a couple VMWare ESXi servers. I can't do any "true" benchmarks because this is a production system (no budget for test systems), but using dd and bonnie++ I can't get more than ~40-50MB/s writes and ~70-90MB/s reads. It seems I should be able to do much better, but I'm not sure where to optimize. Based on what I've read, I think dropping in a OCZ Vertex 2 Pro SSD as my L2ARC is going to be the best bang-for-the-buck to improve througput. Is there something else I should be looking into to help performance? If not... How do I know how big a cache device I need? Am I safe with only a single SSD as my cache device?

    Read the article

  • Enable CPU fan always on

    - by Gundars Meness
    I am using 3 years old overheating laptop and I want my CPU fan to be spinning 24/7 regardless of the consequences. How to make it spin? The problem is that CPU & GPU heats up to 68°C (154 F) right after boot and never goes down, because CPU fan is not spinning full throttle. It starts spinning faster when temperature goes over 70°C and stops when it reaches seventy again. When doing heavy work on databases, it gets from 70 to 90 in no-time and automatically powers off. Bios does not contain any "fan spin 100%" options, just "spin slowly all the time" and "auto" which is more useless than the first one since my fan doesn't have pwm wire. Currently I'm solving this with cooling stand (3x5V), but it isn't much of a help. I would rather use the CPU fan since it is the only fan directly responsible for cooling down CPU/GPU. But how to make it spin 100% all the time? Should I attach it's red power wire to motherboard to get constant 5V (is there such option?), or is there an option to control it via software? Laptop: Samsung R528 2.3 GHz Intel i3 with Nvidia GeForce 310M Bios: Phoenix 03KT.M003.20100622.KSJ (and that is latest update) OS: Ubuntu 12.04.2 LTS with 3.2.0.51 kernel CPU fan: Image/Description Has 5V 0,4A and only 3 pins, no pwm. P.S. Yes, I did clean everything with alcohol, freed the air vents, changed thermal paste etc; that reduced temperature by 4 degrees.

    Read the article

  • Apache2 slow serving static while healthy

    - by user45339
    My Apache status looks like; 201 requests/sec - 98.8 kB/second - 504 B/request 85 requests currently being processed, 345 idle workers _____CCW_C_____C__C__C_R____C_WC_________C__C____CW__C__CCC_____ __C____W______C___C___CW__C_C______C__W_C__C_____CCC____C______R CC_C_______C___C____C______________C______C__C________________C_ ___________________C______________________C_______C___C_____C___ CC____C__C___R_____C_C_CC__________C___C___________R____C_C_C___ ______C______W_W__W___C____________________C__WCC__R__R_C_______ R__RC________________________C___R____W__C____.................. .................................................... Server load is average 2 on a 4 core machine. IO utilization is 10-15% and doesn't have many jumps over 70%. Machine has almost 4 gb free and uses 0 swap. The site on the machine is a PHP site. All PHP code is optimized and fast mostly when it gets accessed, however sometimes requests get stuck. Stuck meaning; no response for at least 10 sec. We debugged the PHP code, but it is quite optimal and fast. We spend a lot of time on it until we decided to test the requesting of: <html><body>test</body></html> test.html page. This static resource also gets 'stuck' in the same manner the php pages get 'stuck'. How is the possible given the health of the system? I tested the network, but, when the PHP shows 'slowness' in the site monitoring, the html test files also take (far longer) than 10 sec to load using; time lynx -dump http://127.0.0.1/test.html We are kind of desperate to solve this problem, but we cannot seem to tackle it.

    Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >