Search Results

Search found 1587 results on 64 pages for 'ultimate'.

Page 48/64 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >

• Computer sponteously reboots when doing heavy file copy to/from disk

  - by Mark Hosang

  I've been fighting with this problem for the last 3 weeks where my machine will just instantly reboot. No BSOD, and when i checked the event log all that was reported was the generic "Kernal-power" error with the detailed information pointing to a hard crash. This is a machine that was working for 18 months before these crashes started happening. When they started happening is after I added 3 HDs in a RAID-5, upped the memory to 12gb, moved to a new house, added a SSD and added about 5 case fans. I have thus eliminated the RAID, and determined that the SSD was not the cause (because it was still crashing even though the ssd wasn't connected). I've run memtest several times over night with no memory problems showing up. I've run IntelBurnTest to max out the cpu to see if it was a heat issue and at full tilt after 20 min it was only at 85C and the machine didn't crash. I also took a look at the voltages during this test, with a screenshot at the bottom of this post I've ruled out a software issue by reinstalling windows 7 ultimate x64 a total of 5 times, but even during that the install it crashes. Happens sometime during file copying at the beginning, or during uncompressing files, or sometimes during running windows update. The only discernible pattern i can see is that it seems to crash when hard disks might be spinning up or when they are accessed heavily from large file transfers. My current guess is that it is probably an issue with the MB, PSU or the power coming through the outlet. Any suggestions of what i could try to troubleshoot or what may be wrong? Specs PSU: Seasonic M12 700w Mem: 12gb CPU: i7-920 with stock heatsink MB: Asus P6T HDs: 3 green WD and 1 Corsair force 3 120b with 1.3.3 firmware Running full tilt voltages Idling Voltages

  Read the article

• Synchronising a remote folder with a local one.

  - by Workshop Alex

  I am using a network disk (that's connected to my router by USB) to store several data files. A simple .NET application that I've created is supposed to read and modify these data files. However, some security issues are preventing this application to access these files directly. (Actually, these have been built-in to my application on purpose since it's not going to support NAS disks.) Since this disk is shared with several computers, I just want to have a simple synchronisation method, which will copy the files to a local folder where3 my application can access them. And, once modified, it should send back the modified files to the NAS disk again. I have two options: 1) Build a second application to do my own synchronisation. 2) Find some build-in function inside Windows 7 Ultimate which can do this for me. Option 2 is preferred. Option 1 is something I can do easily, if need be. I don't need third-party tools. (Still, feel free to add some references to good tools, although I won't accept them as answers.) Basically, is this possible with Windows 7 and if so, how?

  Read the article

• How to use SSH Public Key with PuTTY to connect to a Linux machine

  - by ysap

  I am trying to set a public SSH key connection from a Windows 7 machine to a Red-Hat Linux machine. The ultimate purpose is to use pscp (PuTTY's version of scp) from the command terminal w/o the need to type password repetitively. Following PuTTY's documentation and other online sources, I used PuTTYgen to generate a key pair. I then copied the generated public key to a ~/.ssh/authorized_keys file on the Linux machine (as far as I can tell, it runs OpenSSH server). To check the connection, I run PuTTY and set the username and private key file in the appropriate places in its GUI. However, when trying to connect using PuTTY's SSH, the connection uses the preset username, but I get an error message of "Server refused our key" and a prompt for the password. I then tried to copy-paste the public key text from PuTTYgen's GUI to the authorized_keys file, but it did not work either. How should I set up a public key connection form Win 7 to Linux? How do I use this with pscp (rather than PuTTY's ssh)?

  Read the article

• Windows 7 loses correct time zone upon reboot

  - by Android Eve

  I have a standard PC running Windows 7 Ultimate (64-bit). For some reason, it refuses to keep the correct time zone (the BIOS battery is OK) when restarted. Note (1): The Time zone is correct. The "Internet Time" tab also shows "this computer is set to automatically synchronize with 'time.windows.com'. When I click the 'Change settings...' button, the 'Synchronize with an Internet time server' checkbox is checked. Still, upon reboot, the time is skewed by 6 hours... and doesn't correct itself even after waiting hours for this "automatically synchronize" to occur. Note (2): The BIOS time is set to local (i.e. not UTC). When I restart Windows 7 without booting to the other OS installed in dual-boot config (Ubuntu Linux), it seems to correctly remember the time. This may explain immediate time upon reboot, but it doesn't explain why Windows 7 won't automatically 'Synchronize with an Internet time server' even after an hour. Why is this happening and how do I correct this?

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• Control Panel as menu includes a blank item

  - by Matthew Ferreira

  When viewed as a menu attached to the Start Menu in Windows 7 Ultimate x64, the Control Panel contains a blank item. It looks like this: This item cannot be deleted or removed. I also cannot create a shortcut to it. No error message is displayed, instead simply nothing happens. I've tried using Shell Object Editor (using Run as Administrator) to find out if there is an errant entry on the Control Panel, but many entries (almost two dozen) are blank. There are several valid entries as well. I've looked through the registry and through C:\Windows, \system32, and \SysWOW64 but have had no success. I looked at this question, but I am not using Windows XP and thus have no option to use Tweak UI's Rebuild Icons function. Please note that this is no empty entry in the Control Panel when opened normally, only when attached to the Start Menu as a menu. I have compared the list of entries on the attached menu to the normal Control Panel and other than the blank entry, they are exactly the same. Nothing is missing from one or the other. I've also compared the menu and the normal view to reference images and lists of Control Panel items and have found no irregularities. Is anyone familiar with this problem or know of a solution? I've performed virus and malware scans and found nothing. I've used CCleaner with no change. Nothing with Shell Object Editor. Nothing with Registry Editor. Certainly someone here knows how to fix this. My only guess is the many blank entries visible in Shell Object Editor, but I am reluctant to delete that many items without further analysis and guidance. I appreciate your time and consideration.

  Read the article

• Webcam becomes "Unknown Device" after Windows Messenger 2011 is installed

  - by Boris

  I have Sony VAIO VGN-NS290J laptop. I installed Windows 7 Ultimate 64-bit. I was able to find drivers for all hardware without any problems. Recently, I installed Microsoft Windows Live Essentials 2011, i.e. Windows Live Messenger 2011. Ever since that application is running on my computer, my webcam is not recognized by the OS any more. It is listed as the "Unknown Device" and placed in the Universal Serial Bus controllers group in the Device Manager. There don't seem to be any drivers for this webcam. It's a standard Sony Motion Eye web camera and Sony does not offer any drivers for it. There is one application to download that utilizes the camera, but there are no drivers (and the system is showing the same behavior regardless of the presence of the application). It happens from time to time that the webcam becomes recognized by the OS again, after a couple of restarts; but not always. Then it becomes unknown again. I am absolutely positive that this issue is caused by the Windows Live Messenger 2011, because same symptoms caused the same effects before. I wish to be able to continue to use this software, but also to use my webcam. I was wondering if anyone had a similar issue and if there is a way to fix it. Thanks for all the help, I appreciate it. Update: I have discovered a pattern - if the camera goes astray, restarting the machine does not bring it back; but switching the computer off and turning it back on does. Every time! This is getting super complicated :)

  Read the article

• Ubuntu server crashes; need help figuring how to figure out why

  - by neezer

  I have a 768 Slice at slicehost.com running Ubuntu Server 8.04.2 LTS (hardy) with a LAMP stack on it that periodically crashes, though why I am not sure. From what I can tell, there is a process that basically goes rogue and consumes all the memory on the slice, suffocating all the other programs running until the whole thing comes to a grinding halt, and I have to do a hard reboot of the slice to get it back up and running again. I can't detect any pattern for this (it seems to happen about once a month, more or less). Here's a screenshot of my console during the last crash: I would assume that a possible cause might a PHP script or an apache configuration rule that might cause the crash if triggered? How would I be able to find out which one is the offending one? I've checked and rechecked all my PHP scripts, and running them doesn't seem to trigger the crash. I've also been able to log on to my system during a crash and see what's running (with top), but I can't tell how the offending process was started, so I can't trace the root of the problem! I know my description is overly generic, but unfortunately my expertise in tracking down the source of these glitches is very limited. If you need any additional information about my system in order to help me figure this out, please let me know in the comments, and I will append it to the question. My only other lead as to the culprit here is Wordpress, which we have installed on this server. Here are the details: Wordpress 3.0.3 with the following plugins installed and activated: Addmarx - Bookmark/Share/Email Dropdown, Akismet, All in One SEO Pack, Animated Banners, Automatically publish highlights of any website, directly to your Blog, Broken Link Checker, CMS Dashboard, Collapsing Categories, Status Updater, SubHeading, Ultimate Google Analytics, VastSubCat, WP-CMS Post Control, and WP Super Cache

  Read the article

• Why does Windows 7 have three system partitions?

  - by Ben

  I am using Windows 7, and I wanted to make a System image (using Windows 7), but Windows 7 checked three partitions as System (100 MB + C (install partition) + D (my partition for my files, all programs are installed at C)). I don't want to backup my D partition, but that is not really the point. I don't want Windows messing with my other partitions and making them system. Is there a way to limit Windows 7 just to partition C (install partition)? If there is no way to stop Windows from making other partitions system, can I at least delete the files that make partition D system? PS: All these three partitions are on one physical disk, partitions from other disks aren't treated as System. FACTS: desktop PC, no OEM partitions, I personally have installed Windows 7 (many times) on the C partition. Why is my D partition checked as System partition when I try to create a System Image (using Windows 7 Ultimate built in tool), even though Windows (and all the software) are installed on the C partition? Is there a way to make D "normal" or non-system partition? Here is a picture of how it looks like if I try to create a system image. Once again, why is D also a system partition?

  Read the article

• VNC Address Book - Window Invisible? Working as intended?

  - by user1445967

  I have VNC Server and VNC Viewer on the same PC with Windows 7 Ultimate x64. Is VNC Address Book supposed to have a main application window? I can't tell if this is bugged or working as intended. When I start VNC Address book, it creates an item in the task list and also an icon in the notification area. If I click the task list item once, nothing happens. If I click again, it disappears from the task list but remains in the notification area**. If I right-click the icon on the notification area, there is an option 'open address book', which if chosen, creates the item in the task list again, with the exact same behavior. If I left or right click on the address book icon, I have ways to connect to servers in the address book. However I have no way to add/remove/edit servers in the address book. **Note that this behavior is identical to that of an application with a main window where there is an option to 'minimize to system tray / notification area'. Only here, no main window is visible, ever. If fixing this problem is beyond the scope of this site, that's fine, but at this point I have no real way to tell if the program is malfunctioning on my pc or if it is far more minimalist than I expected. There appears to be no forum on realvnc.com where I can ask about this, perhaps this is to prevent me from getting any help unless I pay to register?

  Read the article

• Windows 7: Moving Program Files location during install using unattend.xml

  - by Shevek

  I am planning on using an unattend.xml to create a Windows 7 Ultimate 64-bit setup with Users and ProgramData on a 2nd drive. I have found many samples of how to do this (see below). However I would also like to move Program Files to a 3rd drive as well. i.e.: C:\Windows [SSD] D:\Users [HDD1] D:\ProgramData [HDD1] P:\Program Files [HDD2] P:\Program Files (x86) [HDD2] I have found that this was possible using unattend.txt in XP but all documentation or examples I find about Win 7 only mention Users and ProgramData, not Program Files. Is this possible using an answer file? Sample unattend.xml for Users and ProgramData: <?xml version="1.0" encoding="utf-8"?> <unattend xmlns="urn:schemas-microsoft-com:unattend"> <settings pass="oobeSystem"> <component name="Microsoft-Windows-Shell-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <FolderLocations> <ProfilesDirectory>D:\Users</ProfilesDirectory> <ProgramData>D:\ProgramData</ProgramData> </FolderLocations> </component> </settings> </unattend>

  Read the article

• Parallels 6 - Is It Just Me or Does It Run Really Slowly?

  - by 5arx

  I've been running Parallels since version 2 with great success. I use it as my .Net development environment and over the last few years have converted so many others to the Parallels/Mac way of doing Windows/.Net development that I feel I should be getting perks/gifts and/or freebies from Parallels Corporation ;-) A month or so ago I upgraded to version 6 and ... immediately wished I hadn't. I'm currently running it on a laptop - a 2009 MacBook Pro (13"/2.53Ghz/4GB) while my MacPros at work and home are still running v5. I have seen nothing in v6 that makes me want to upgrade the install on those. The general problem is performance - upon starting or suspending a vm (always Windows 7 Ultimate), OS X slows down, quite often freezing for a minute or two at a time. The performance of the vms themselves are fine, but for me the point of this set-up is to be able to do web-browsing, email checking etc. on the OS X side of things while doing the stuff that can only be done on Windows (Visual Studio, SQL Server tools) on Windows. I have been using Parallels for a while so at least feel like I know what I'm doing so at the moment I am heading towards forming an opinion that its Parallels thats to blame. I've tweaked and tweaked all the vm configuration properties but to no avail. Support emails to the company have all received replies - there are no documented case of the issue you mention. Has anyone else seen this problem and if so, have you found a fix?

  Read the article

• Second monitor stopped being recognized by Windows

  - by Eric J.

  One of the developer PC's running Windows Vista Ultimate had the second monitor stop being recognized in Windows overnight. There were no hardware or driver changes at the time, though I have subsequently updated to the latest nVidia drivers (card is NVIDIA GeForce 210). The non-recognized monitor IS recognized during the boot sequence. In fact, only the "bad" one shows the POST or the Windows loading screen. At some point during Windows initialization after the loading screen disappears and before the logon screen appears, the active monitor switches. Any thoughts? UPDATE: When I open the Vista monitor properties window, I see my primary display and secondary display depicted. The primary one is portrayed as the regular blue box, but the secondary one is portrayed greyed-out. I have the option to "Extend desktop to this monitor", the only resolution is 800x600, and all of the advanced monitor properties are greyed out as well. If I opt to extend the desktop, the greyed-out box turns blue, when I then select Apply the screens flash as usual and I'm given the 15 second countdown to accept the new settings and when I do, everything returns to the previously broken state... secondary monitor is portrayed greyed-out again. At no point is the desktop shown on the secondary monitor.

  Read the article

• Wireless keeps shutting off in Windows 7

  - by Nathan Adams

  I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

  Read the article

• Windows 7 System File Checker (sfc) not working

  - by Andrew

  I have a strange problem with Windows 7 RTM. I'm running Ultimate 64-bit edition. Whenever I run sfc /scannow I get this error: Windows Resource Protection could not start the repair service. My research so far has told me that I need to set the Windows Module Installer and Windows Installer services' startup types to Manual. They already were, so I manually started those services and tried again. No luck. I've even booted into my Windows 7 repair disc and tried running sfc /scannow from that. All I get is this: A repair operation is already pending. Restart and try again. History: I'm trying to run sfc because I am unable to open any images in Windows Photo Viewer. Whenever I try, I get the error "Class not registered." I believe the problem started after I installed Gladinet, but I can't be sure. I've uninstalled Gladinet, but the problem remains. System Restore was disabled (yes, I know I'm stupid - you don't have to remind me). Please help. Thanks.

  Read the article

• iTunes Title Bar is Equal to the Location of the Library file?

  - by Urda

  I have never been able to get a clear answer on why the latest edition of iTunes does this. I have my entire iTunes library located in C:\itunes\ and the library data files inside C:\itunes\!library_info for backup purposes. However when version 9 of iTunes came out it went from having iTunes as the title, to !library_info. Anyway to get around this without moving my data files away? Annoying "feature" if that is what it is. Again Apple support and forums were of no help to me. Anyone have insight on this? System Info: Windows Vista x86 Ultimate, latest updates. iTunes Version 9.0.3.15 Screenshot: http://farm5.static.flickr.com/4072/4414557544_d0b25eb64c_o.jpg Flickr Page: http://www.flickr.com/photos/urda/4414557544/ UPDATE: I put a bounty on this, and would be open to hacking the registry or doing a custom config. Please help me fix my title bar!!! Update2: I would not like to move my library files out of itunes\!library_info to avoid them inter-mingling with my music library.

  Read the article

• Windows 7 Startup fails after installation

  - by Nadav S.

  I have installed Windows 7 Ultimate a week ago. Yesterday I've noticed that the SP1 update is available. After installation of SP1 the computer failed to startup, and had shown a black screen. I couldn't even go to safe mode and F8 didn't help. After some fixing attempts including system restore, startup repair, bootmgr & BCD rebuilding from CMD, I have decided to reinstall Windows (after all, it's only a week old) After the successful installation, I have decided to first install all available updates before I continue. So after the updates download & installation, the computer rebooted. And now I didn't see the black screen again - but in the "Starting Windows..." screen the logo didn't appear and the system didn't startup. Here I could go to safe mode selection window, but it didn't work either ("Loading Windows Files" but nothing). I've also tried: I thought that the CD was corrupted, so I've used a fresh new disk of Windows, tried x86 & x64 versions, the same symptoms, no change. Resetted the BIOS to default, no change. Memory diagnostic HDD diagnostic Restarted Windows WITHOUT INSTALLING UPDATES, but it had the same symptom, so maybe Windows Update is not the case?! I've tried installing it so many times - that I am simply stuck - I can't "reinstall Windows, because it is corrupted...". Maybe the HDD is corrupted? I've also checked it and didn't find a problem.

  Read the article

• Gigabit LAN not working on ASUS M2N-MX

  - by chmod

  Today I replace my FastEthernet switch with a newly bought gigabit switch (DGS-1008A). All computers in my house are displaying that the connection speed is 1 Gbps except for one. The computer that is not working is an ASUS M2N-MX which contain an onboard gigabit NIC. See ASUS link for confirmation http://www.asus.com/Motherboards/AMD_AM2/M2NMX/ Here are some info of the machine OS: Windows 7 Ultimate SP1 64bit BIOS version: 1004 (latest) Driver: installed via Windows update (latest from Windows update) Windows Update: fully updated The machine is reformatted 3 days ago, so it's pretty clean, no junk, no virus, etc Cable: Amp CAT5E 5 meters In device manager, the name of the NIC is "NVIDIA nForce 10/100/1000 Mbps Ethernet" What I have try: I did try to install the driver provided in ASUS website, but there isn't any for Windows 7 64 or Vista 64. I did try to install the latest nForce340/6100, downloaded from Nvidia website. However, the LAN driver refuse to install, it complain that I already have the best driver installed. I looking in the property -- advance tab -- Speed/duplex settings, in an attempt to force it to run at 1000Mbps, but there is no 1000Mbps choice, only 10 and 100Mpbs. I change the CAT5E cable (use one from another computer that is running gigabit without problem) Anyone have this issue or know how to solve it? Thanks

  Read the article

• Photoshop CS5 performance over network drive (cifs)

  - by grub

  Hello Everyone I did install a QNAP NAS TS410 for a customer (professional photographer) with 3 Hitachi Deskstar 7200rpm 2TB disk configured as RAID5. The NAS and the workstations are connected over a Gigabit network. He and his co-worker are accessing the photos (about 1TB of photos) over a mapped network drive from their windows machines (Windows XP - 32bit and Windows 7 Ultimate - 32bit). Both are using Photoshop CS5 to edit the photos. The problem is that to save a edited photo takes a really long time, it takes about 3 times as long to save a photo as to open it. After some tests I can exclude the network, the NAS and the windows machines as source of the issue. I think the problem is the Photoshop software and its handling of the network drives. Officially network drives are not supported by Adobe. I do not have any experience with the Adobe products, especially with Adobe Photoshop CS5. What are your recommendation to solve the performance issue? Should my customer copy the photos to the local drive, edit them and upload them again to the network drive or is Adobe Drive or Adobe Version Cue the answer? One requirement is that the photos need to be accessible / editable from both computers even when one of them is offline. Adobe Version Cue needs a dedicated service running to be usable, so this solution is not possible as far as I understand the Cue software. Thank you for your input to this issue and have a nice day :-) Greetings grub

  Read the article

• Windows freezes when watching videos

  - by cornerback84

  I have Acer laptop Aspire 5740 - 5780 with windows 7 Ultimate 32 bit. I am using Chrome. Windows is 1 year old, but it's not the first time this has happened. Windows freezes whenever I am watching videos on facebook/youtube or when using SopCast. I thought there was some faulty plugin, so I recently re-installed chrome but it happened again. No keys work, and the sound of whatever I am listening starts repeating like grrrr..drrrr. Its seems like the sound in very slow motion. One time I left it in this freeze state for 5 min and it recovered automatically. It usually does not happen when I am using windows media player. I had some codecs installed but I removed them to see if that fixes. So far, I have narrowed it down to youtube/footytube videos and sopcast. I have checked event logs but nothing special. Is there any way I can narrow down the problem or any suggestions on how to fix it. I'd like to add that it does not always happen. Sometimes windows goes days/weeks without freezing, and sometimes it take a min into video to freeze.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• Not able to access Silverlight.net and ONLY Silverlight.net - All other domains work!

  - by Sootah

  Alrighty folks, I have an extremely odd problem. I am able to surf the web fine with one odd (and really annoying at the moment) exception: Microsoft's Silverlight.net. Every other site that I go to works just fine. This is quite frustrating because I'm in the middle of programming a web app in Silverlight 4.0, and whenever I do a search for any code examples, tutorials, or whatnot at least 50% of the results are hosted in the silverlight.net forums. The error message that I get is: Oops! Google Chrome could not find www.silverlight.net It doesn't work in my other browsers either (both IE and FireFox). What's odd, is that while the error message would lead me to assume it's a DNS error, I can ping the URL just fine. C:\Users\The Doot>ping silverlight.net Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Reply from 206.72.125.201: bytes=32 time=106ms TTL=106 Ping statistics for 206.72.125.201: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 103ms, Maximum = 110ms, Average = 106ms I've checked my HOSTS file, and there's nothing that refers to ANY Microsoft URL in there. What could be causing this!?? More importantly, how do I fix it? Just for kicks, I've even included the results of a traceroute here for your enjoyment. OS: Windows 7 Ultimate Thanks in advance! -Sootah

  Read the article

• Basic connectivity issues between Win 7 and XP mixed wired/wireless network.

  - by Pulse

  Setup: Windows 7 x64 Ultimate desktop hard wired to Asus WL500gp router (WL500gpv2-1.9.2.7-d-r1445 firmware) Several Bridged VirtualBox VM's running XP, 7, ubuntu server 10.04, Mint 9 and SuSE 11.2 Win XP Pro SP3 notebook with D-Link Airplus wireless network card. No firewall or other security software currently running on either platform (at least for the duration of the test) Situation: Router is acting DHCP server Clients are receiving correct addresses and additional parameters Internet connectivity is available from all clients Windows 7 sharing is set to Network type = work (not home group) NetBT is disabled on all clients using smb over TCP What I can do: I can ping the router and internet addresses from the wireless XP notebook I can ping the Win 7 desktop and any VM from the XP wireless notebook I can ping all devices from the router All VM's and 7 can ping each other and the router as well as Internet addresses What I can't do: I cannot ping the XP wireless notebook from either The Win 7 desktop or the VM's it alwats returns a destination host unreachable. Tracert resolves the name or the XP notebook but also returns a destination host unreachable. From the above it would seem that something is blocking connectivity in a single direction (from the Win 7 box to the Win XP notebook) only but the router can ping the XP notebook. Some fresh input would be most welcome, as this is beginning to drive me batty. Thanks

  Read the article

• NTFS frequent corruption when writing many small files, index $I30 error

  - by david sedai

  I'm running Windows 7 Ultimate on a laptop with a 500G HDD, and had all partitions formatted as NTFS. I do a lot of programming and LaTeX typesetting, both of these involves a large amount of reading/writing/deleting to a lot of small files, such as C++ library headers or LaTeX packages. The problem is that frequently, when there is a large number of writing to files, the partition being written to often corrupts, the chkntfs e: returns dirty, where e: is the partition being written. I've re-formatted the drive, I've contacted the laptop manufacturer and had the HDD checked, the HDD is not faulty, there are no bad sectors, and I've tried a brand new HDD, to no avail, and the other partition on the same physical drive doesn't have this issue. I'm pretty sure that it's no hardware related. I've searched the Microsoft support pages, one page http://support.microsoft.com/kb/982018 provides an update for Advanced Format Disks, which I've already installed. The chkntfs log shows $130 index errors. I'm at a loss here. Can anyone help? Thanks in advance.

  Read the article

• Permanent fix for unicode characters not displaying correctly (as boxes)

  - by Chase

  Please read this entire message before replying. First I know how to fix the issue on a temporary basis. I am looking for a permanent fix. I work with foreign language files a lot. Unfortunately sometimes all the unicode characters in windows explorer, notepad, and other places (as rendered by windows, probably GDI) do not display correctly. That is they display as square blocks, where as they had just been displaying correctly. There are countless methods to temporarily correct the issue. But again, I want a way to permanently resolve the issue. What I have tried: The silly "Hide fonts based on language settings". This setting only applies to what fonts you see in the fonts folder and font dropdowns. It doesn't disable foreign fonts (doesn't work, or if it does, it is temporary). Deleting the font cache file and rebooting (works.. usually, temporary solution). Changing my locale and then back (sometimes works, temporary solution). Rebooting my PC and getting lucky (50-50 chance, temporary solution). Changing my keyboard input/adding foreign keyboard (temporary solution that only seems to work once). Reinstalling windows (temporary solution, sometimes lasts a few months though, I have done this 7 times across 3 computers) What I have not tried: Buying Windows Ultimate and installing the interface packs. This is not a solution. I can't read Japanese/Chinese and I do not want my interface in those languages. What I will not do: Switch to a different brand operating system (unix, linux, mac os x) Switch to an older version of windows (Windows Vista, XP, 2000, etc). So can anyone recommend a permanent fix for the problem?

  Read the article

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55  | Next Page >