volume label - Page 48 - Developer IT

Why is LSHW Only listing one of my two HDDs?

- by Mark

I have a 120GB HDD and a 1TB HDD in the system. I installed Ubuntu Server using LVM on the 120GB. After installation I added the 1TB to the existing volume group and added 10GB to /home as a test. My understanding is that lshw is supposed to list hardware. What's the difference here? mark@server:~$ sudo lshw -short -c disk H/W path Device Class Description ========================================================= /0/100/1f.2/0 /dev/sda disk 120GB ST3120026AS /0/100/1f.2/1 /dev/cdrom disk DVD+-RW GH50N /0/1/0.0.0 /dev/sdc disk SCSI Disk /0/1/0.0.1 /dev/sdd disk SCSI Disk /0/1/0.0.2 /dev/sde disk SCSI Disk /0/1/0.0.3 /dev/sdf disk SCSI Disk The 1TB only shows up as a volume, not as a disk. mark@server:~$ sudo lshw -short .... /0/100/1f.2/0 /dev/sda disk 120GB ST3120026AS /0/100/1f.2/0/1 /dev/sda1 volume 476MiB Linux filesystem partition /0/100/1f.2/0/2 /dev/sda2 volume 111GiB Linux LVM Physical Volume partition /0/100/1f.2/1 /dev/cdrom disk DVD+-RW GH50N /0/100/1f.2/0.0.0 /dev/sdb volume 931GiB WDC WD1001FALS-0 Thanks, Mark

Read the article

How to install Ubuntu 12.04.1 in EFI mode with Encrypted LVM?

- by g0lem

I'm trying to properly install Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with the alternate install CD ".iso" on a lenovo Thinkpad X220. Default Hard Disk (with a pre-installed version of Windows 7) has been replaced with a brand new SSD. The UEFI BIOS of the lenovo Thinkpad X220 is set to "UEFI Boot only" & "USB UEFI BIOS Support" is enabled (I'm using an external USB DVD reader to perform Ubuntu installation). The BIOS is a Phoenix SecureCore Tiano, BIOS version is 8DET56WW (1.26). The attempts below are made with the UEFI BIOS settings described above. Here's what I've tried so far: Boot on a live GParted CD Create a GPT partition table Create a FAT32 partition for UEFI System, set the partition to "EF00" type ("boot" flag) Leave remaining space unformated Boot on Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with alternate CD: Perform the install with network updates enabled Use manual partitioning FAT32 partition created with GParted is used as "EFI System partition" Remaining space is set to be used as "Physical volume for LVM" Then "Configure encrypted volumes" using the previous "Physical volume for LVM" as the encrypted container, passphrase is setup. "Configure the Logical Volume Manager" creating a volume Group using the encrypted container /dev/mapper/sda2_crypt Creation of the Logical Volumes "Create logical volume", choosing the previously created volume Group Assign a mount point and file system to the Logical volumes : LV-root for / LV-var for /var LV-usr for /usr LV-usr-local for /usr/local LV-swap for swap LV-home for /home NOTE: /tmp would be in RAM only using TMPFS Bootloader step: neither my ESP partition (/dev/sda1, /dev/sda or MBR) seems to be the right place for GRUB, I get the following message (X suffix is for demonstration only): unable to install grub in /dev/sdaX Executing 'grub-install /dev/sdaX' failed This is a fatal error. Finish installation without the Bootloader & Reboot The system doesn't start, there's no EFI/GRUB menu at startup. What are the steps to perform a clean and working installation of Ubuntu 12.04.1 Precise Pangolin, 64bit version in U(EFI) mode using the encrypted LUKS + LVM scheme described above?

Read the article

Will the values of label and its correspondences change if Image is rotated?

- by Vinayak Agarwal

Hi all I have an image in which a text like "VINAYAK 123" is written. The text in the image is at a certain angle, say 30degrees. Now when I extract the labels of the connected components, I get V-1, I-2, N-3, A-4,Y-5,A-6,K-7, 1-8,2-9,3-10( Format: Character- Label No.). Now I rotate the image 30 degrees in the clockwise direction to make the text in the image horizontal. My question is that now if I extract the labels of the connected components, will the character and the label no. correspondence still remain the same? Thanks in advance!

Read the article

How to hide the label (CCLabel) after a certain time in cocos2d ?

- by srikanth rongali

I added a label by using CCLabel to my layer. Now I want it do disappear after some time like (2sec). How can I make it to disappear? CCLabel *labelPerfectDraw = [CCLabel labelWithString:@"Perfect Draw" fontName:@"Marker Felt" fontSize:30 ]; labelPerfectDraw.color = ccc3(0x00, 0x00, 0xff); labelPerfectDraw.position = ccp(windowSize.width/2, windowSize.height/2+80); [self addChild:labelPerfectDraw]; I added label in above way. Please give me the idea how can I work on it?

Read the article

How to add file revision (not the last changed revision) to Subclipse "Label decorations"?

- by mlvljr

Firstly, please beware I'm new to SVN. Then, my question has much in common with Get current revision number in Subclipse?. The (seeming) problem is (I use Ecpilse v3.5.0 (build id I20090611-1540)): My freshly installed Subclipse plugin offers "revision - last revision loaded into workspace" label under "Windows > Preferences > Team > SVN > Label decorations" That seems to correspond to "Last changed revision" under "File > Properties > Subversion" (and not the "Revision" there). Hence, the question.

Read the article

how can i display current time on a label ?

- by suchita

how can i display current time on a label iphone?

Read the article

Creating a form with floats, what is the general design when you need 2 columns, p and label?

- by Blankman

I want to design a form. The form has 3 sections: user info, shipping and billing. Each section will have 2 columns, so form fields and their labels with be on both the left and right side. What technique should I use? How does this look? <div id="forms"> <div id=contact> <div class=left> <p><label>Firstname<label><input type=text /></p> </div> <div class=right></div> </div> <div id=shipping></div> <div id=billing></div> </div> Any tricks with the css i should know about?

Read the article

Label field problem in the treenode Tag. (Struts2/Ajax)

- by ryan

I'm using struts as a framework for a web-app. The following code runs inside a loop where I access the database to retrieve values to be used as nodes for a tree. <s:set name="categoryValue" value= "%{'<%=rs.getString("category")%>'}"> </s:set> <sx:treenode id="child1" label ="%{#categoryValue}"/> The error I get is "/jsp/tree.jsp(249,65) equal symbol expected" However if i give <s:set name="categoryValue" value= "%{'Test'}"> the value Test is obtained. Can anyone tell me how to set the value of the 'label' with strings?

Read the article

How can I plot an iteration coordinate(x,y) data with only label in GNUplot?

- by Mojiiz Alamode

I have the set of data like this 0 268 195 1 353 199 2 318 209 3 268 232 4 370 238 5 326 253 6 246 265 7 372 284 8 313 290 9 258 297 0 268 196 1 353 199 2 318 209 3 268 233 4 370 238 5 325 253 6 246 265 7 372 284 8 313 290 9 258 297 I would like to use first column for label and second and third for (x,y) plot, however, I would like to plot only one time label without iteration. How should I do? Thank you for help.

Read the article

Ubuntu - Automatically mount external drives to /media/LABEL on boot without a user logged in?

- by endolith

This question is similar, but kind of the opposite of what I want. I want external USB drives to be mounted automatically at boot, without anyone logged in, to locations like /media/<label>. I don't want to have to enter all the data into fstab, partially because it's tedious and annoying, but mostly because I can't predict what I'll be plugging into it or how the partitions will change in the future. I want the drives to be accessible to things like MPD, and available when I log in with SSH. gnome-mount seems to only mount things when you are locally logged into a Gnome graphical session.

Read the article

Need help with software licensing? Read on…

- by juanlarios

Figuring out which software licensing options best suit your needs while being cost-effective can be confusing. Some businesses end up making their purchases through retail stores which means they miss out on volume licensing opportunities and others may unknowingly be using unlicensed software which means their business may be at risk. So let me help you make the best decision for your situation. You may want to review this blog post that lays out licensing basics for any organization that needs to license software for more than 5 or less than 250 devices or users. It details the different ways you can buy a license and what choices are available for volume licensing, which can give you pricing advantages and provide flexible options for your business. As technology evolves and more organizations move to online services such as Microsoft Office 365, Microsoft Dynamics CRM Online, Windows Azure Platform, Windows Intune and others, it’s important to understand how to purchase, activate and use online service subscriptions to get the most out of your investment. Once purchased through a volume licensing agreement or the Microsoft Online Subscription Program, these services can be managed through web portals: · Online Services Customer Portal (Microsoft Office 365, Microsoft Intune) · Dynamics CRM Online Customer Portal (Microsoft Dynamics CRM Online) · Windows Azure Customer Portal (Windows Azure Platform) · Volume Licensing Service Center (other services) Learn more >> Licensing Resources: The SMB How to Buy Portal – receive clear purchasing and licensing information that is easy to understand in order to help facilitate quick decision making. Microsoft License Advisor (MLA) – Use MLA to research Microsoft Volume Licensing products, programs and pricing. Volume Licensing Service Center (VLSC) – Already have a volume License? Use the VLSC to get you easy access to all your licensing information in one location. Online Services – licensing information for off-premise options. Windows 7 Comparison: – Compare versions of Windows and find out which one is right for you. Office 2010 Comparison: – Find out which Office suite is right for you. Licensing FAQs – Frequently Asked Questions About Product Licensing. Additional Resources You May Find Useful: · TechNet Evaluation Center Try some of our latest Microsoft products For free, Like System Center 2012 Pre-Release Products, and evaluate them before you buy. · Springboard Series Your destination for technical resources, free tools and expert guidance to ease the deployment and management of your Windows-based client infrastructure. · AlignIT Manager Tech Talk Series A monthly streamed video series with a range of topics for both infrastructure and development managers. Ask questions and participate real-time or watch the on-demand recording.

Read the article

VS 2010 Debugger Improvements (BreakPoints, DataTips, Import/Export)

- by ScottGu

This is the twenty-first in a series of blog posts I’m doing on the VS 2010 and .NET 4 release. Today’s blog post covers a few of the nice usability improvements coming with the VS 2010 debugger. The VS 2010 debugger has a ton of great new capabilities. Features like Intellitrace (aka historical debugging), the new parallel/multithreaded debugging capabilities, and dump debuging support typically get a ton of (well deserved) buzz and attention when people talk about the debugging improvements with this release. I’ll be doing blog posts in the future that demonstrate how to take advantage of them as well. With today’s post, though, I thought I’d start off by covering a few small, but nice, debugger usability improvements that were also included with the VS 2010 release, and which I think you’ll find useful. Breakpoint Labels VS 2010 includes new support for better managing debugger breakpoints. One particularly useful feature is called “Breakpoint Labels” – it enables much better grouping and filtering of breakpoints within a project or across a solution. With previous releases of Visual Studio you had to manage each debugger breakpoint as a separate item. Managing each breakpoint separately can be a pain with large projects and for cases when you want to maintain “logical groups” of breakpoints that you turn on/off depending on what you are debugging. Using the new VS 2010 “breakpoint labeling” feature you can now name these “groups” of breakpoints and manage them as a unit. Grouping Multiple Breakpoints Together using a Label Below is a screen-shot of the breakpoints window within Visual Studio 2010. This lists all of the breakpoints defined within my solution (which in this case is the ASP.NET MVC 2 code base): The first and last breakpoint in the list above breaks into the debugger when a Controller instance is created or released by the ASP.NET MVC Framework. Using VS 2010, I can now select these two breakpoints, right-click, and then select the new “Edit labels…” menu command to give them a common label/name (making them easier to find and manage): Below is the dialog that appears when I select the “Edit labels” command. We can use it to create a new string label for our breakpoints or select an existing one we have already defined. In this case we’ll create a new label called “Lifetime Management” to describe what these two breakpoints cover: When we press the OK button our two selected breakpoints will be grouped under the newly created “Lifetime Management” label: Filtering/Sorting Breakpoints by Label We can use the “Search” combobox to quickly filter/sort breakpoints by label. Below we are only showing those breakpoints with the “Lifetime Management” label: Toggling Breakpoints On/Off by Label We can also toggle sets of breakpoints on/off by label group. We can simply filter by the label group, do a Ctrl-A to select all the breakpoints, and then enable/disable all of them with a single click: Importing/Exporting Breakpoints VS 2010 now supports importing/exporting breakpoints to XML files – which you can then pass off to another developer, attach to a bug report, or simply re-load later. To export only a subset of breakpoints, you can filter by a particular label and then click the “Export breakpoint” button in the Breakpoints window: Above I’ve filtered my breakpoint list to only export two particular breakpoints (specific to a bug that I’m chasing down). I can export these breakpoints to an XML file and then attach it to a bug report or email – which will enable another developer to easily setup the debugger in the correct state to investigate it on a separate machine. Pinned DataTips Visual Studio 2010 also includes some nice new “DataTip pinning” features that enable you to better see and track variable and expression values when in the debugger. Simply hover over a variable or expression within the debugger to expose its DataTip (which is a tooltip that displays its value) – and then click the new “pin” button on it to make the DataTip always visible: You can “pin” any number of DataTips you want onto the screen. In addition to pinning top-level variables, you can also drill into the sub-properties on variables and pin them as well. Below I’ve “pinned” three variables: “category”, “Request.RawUrl” and “Request.LogonUserIdentity.Name”. Note that these last two variable are sub-properties of the “Request” object. Associating Comments with Pinned DataTips Hovering over a pinned DataTip exposes some additional UI within the debugger: Clicking the comment button at the bottom of this UI expands the DataTip - and allows you to optionally add a comment with it: This makes it really easy to attach and track debugging notes: Pinned DataTips are usable across both Debug Sessions and Visual Studio Sessions Pinned DataTips can be used across multiple debugger sessions. This means that if you stop the debugger, make a code change, and then recompile and start a new debug session - any pinned DataTips will still be there, along with any comments you associate with them. Pinned DataTips can also be used across multiple Visual Studio sessions. This means that if you close your project, shutdown Visual Studio, and then later open the project up again – any pinned DataTips will still be there, along with any comments you associate with them. See the Value from Last Debug Session (Great Code Editor Feature) How many times have you ever stopped the debugger only to go back to your code and say: $#@! – what was the value of that variable again??? One of the nice things about pinned DataTips is that they keep track of their “last value from debug session” – and you can look these values up within the VB/C# code editor even when the debugger is no longer running. DataTips are by default hidden when you are in the code editor and the debugger isn’t running. On the left-hand margin of the code editor, though, you’ll find a push-pin for each pinned DataTip that you’ve previously setup: Hovering your mouse over a pinned DataTip will cause it to display on the screen. Below you can see what happens when I hover over the first pin in the editor - it displays our debug session’s last values for the “Request” object DataTip along with the comment we associated with them: This makes it much easier to keep track of state and conditions as you toggle between code editing mode and debugging mode on your projects. Importing/Exporting Pinned DataTips As I mentioned earlier in this post, pinned DataTips are by default saved across Visual Studio sessions (you don’t need to do anything to enable this). VS 2010 also now supports importing/exporting pinned DataTips to XML files – which you can then pass off to other developers, attach to a bug report, or simply re-load later. Combined with the new support for importing/exporting breakpoints, this makes it much easier for multiple developers to share debugger configurations and collaborate across debug sessions. Summary Visual Studio 2010 includes a bunch of great new debugger features – both big and small. Today’s post shared some of the nice debugger usability improvements. All of the features above are supported with the Visual Studio 2010 Professional edition (the Pinned DataTip features are also supported in the free Visual Studio 2010 Express Editions) I’ll be covering some of the “big big” new debugging features like Intellitrace, parallel/multithreaded debugging, and dump file analysis in future blog posts. Hope this helps, Scott P.S. In addition to blogging, I am also now using Twitter for quick updates and to share links. Follow me at: twitter.com/scottgu

Read the article

Printing labels from an android app or Java? [on hold]

- by user3563124

I've seen others discussing printing labels with a dedicated label printer using Java. Is there any way to print labels using a regular printer with label paper using (optimally) Android libraries/API? If not, is there any way to do this in a non-mobile context using Java? Searching for "Java Label Printing" is only turning up the aforementioned dedicated label printing bits, which aren't quite what I'm looking for.

Read the article

Bladecenter-E Power Module fault

- by Lihnjo

We have problem on IBM Bladecenter-E Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy What is the best solution for this problem? Thanks AMM Service Data Help SPAPP Capture Available 10/13/2010 17:03:47 1090347 bytes Time: 11/19/2012 11:02:31 UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 MAC Address xx:xx:xx:xx:xx:xx MM Information Name: nnnnn Contact: aaa, bbb, ccc, England Location: [email protected] IP address: 111.222.333.444 Date Time Information GMT offset: +1:00 - Central Europe Time (Western Europe, Algeria, Nigeria, Angola) Adjust for DST: Yes NTP: Enabled NTP Hostname/IP: 111.222.333.444 System Health: Critical System Status Summary One or more monitored parameters are abnormal. Critical Events Power module 2 is off. DC fault. Power module 4 is off. DC fault. Warnings and System Events Insufficient chassis power to support redundancy CHASSIS (BladeCenter-E) in CHASSIS slot: 01 TopoPath is "CHASSIS[1]". Description : BladeCenter-E Width : 1 Sub Type : BladeCenter (BC) Power Mode : 220 v KVM Owner : CHASSIS[1]/BLADE[9] MT Owner : CHASSIS[1]/MGMT_MOD[1] Component Type : CHASSIS Inventory: VPD ID: 336 (decimal) POS ID EXT: 0 (decimal) POS ID: 8 (decimal) Machine Type/Model: 86773RG Machine Serial Number: 99ZL816 Part Number: 39R8561 FRU Number: 39R8563 FRU Serial Number: YK109174W1HV Manufacturer ID: IBM Hardware Revision: 3 (decimal) Manufacture Date: 18 (wk), 07 (yr) UUID: 42E1 5D2F D7BF 41A6 A4A2 48D1 3FB7 0540 (hex) Type Code: 97 (decimal) Sub-type Code: 0 (decimal) IANA Num: 336 (decimal) Product ID: 8 (decimal) Manufacturer Sub ID: FOXC Enviroment data: -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0xa Sensor Label: : Midplane Sensor ID: : 0x0 MGMT MOD (Advanced Management Module) in MGMT_MOD slot: 01 TopoPath is "CHASSIS[1]/MGMT_MOD[1]". Description : Advanced Management Module Name : kant Width : 1 Component Role : Primary Component Type : MGMT MOD Insert Time : 28050132 Inventory: VPD ID: 288 (decimal) POS ID EXT: 0 (decimal) POS ID: 4 (decimal) Part Number: 39Y9659 FRU Number: 39Y9661 FRU Serial Number: YK11836CE2RC Manufacturer ID: IBM Hardware Revision: 4 (decimal) Manufacture Date: 50 (wk), 06 (yr) UUID: 1D95 9937 8CA5 11DB 9499 0014 5EDF 1C98 (hex) Type Code: 81 (decimal) Sub-type Code: 1 (decimal) IANA Num: 20301 (decimal) Product ID: 65 (decimal) Manufacturer Sub ID: ASUS Firmware data: Type : AMM firmware Build ID : BPET50P File Name : CNETCMUS.PKT Release Date : 03/26/2010 Release Level : 50 Revision - Major: 80 Port info: ======================================================== Topology Path ID : 1 Label : External Phy Orientation : EXTERNAL Port Number : 1 Type : MGT Physical Meidum : Copper Number of Link Intferfaces : 1 ------------------------------------ Link Ifc ID Number : 1 Link Ifc Transport Protocol : ENET Link Ifc Addr Type : MAC Link Ifc Burned-in Addr : xx:xx:xx:xx:xx:xx Link Ifc Admin Addr : 00:00:00:00:00:00 Link Ifc Addr in use : xx:xx:xx:xx:xx:xx ---------------------------------------------------------- Configuration behaviors: Save Only Enviroment data: -------------- Type: : TEMPERATURE Unit: : DEGREES_C Reading: : 38.00 Sensor Label: : MM Ambient Sensor ID: : 0x0 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +4.81 Sensor Label: : +5V Sensor ID: : 0x1b -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +3.26 Sensor Label: : +3.3V Sensor ID: : 0x19 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +11.97 Sensor Label: : +12V Sensor ID: : 0x16 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : -4.88 Sensor Label: : -5V Sensor ID: : 0x1e -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +2.47 Sensor Label: : +2.5V Sensor ID: : 0x18 -------------- Type: : VOLTAGE Unit: : VOLTS Reading: : +1.76 Sensor Label: : +1.8V Sensor ID: : 0x15 -------------- Type: : POWER_USAGE Unit: : WATTS Reading: : 0x19 Sensor Label: : kant Sensor ID: : 0x0

Read the article

Bash-Scripting - Munin Plugin don't work

- by FTV Admin

i have written a munin-plugin to count the http-statuscodes of lighttpd. The script: #!/bin/bash ###################################### # Munin-Script: Lighttpd-Statuscodes # ###################################### ##Config # path to lighttpd access.log LIGHTTPD_ACCESS_LOG_PATH="/var/log/lighttpd/access.log" # rows to parse in logfile (higher value incrase time to run plugin. if value to low you may get bad counting) LOG_ROWS="200000" # #munin case $1 in autoconf) # check config AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then echo "yes" else echo "No: "$AVAILABLE echo "Please check your config!" fi exit 0;; config) # graph config cat <<'EOM' graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx EOM exit 0;; esac ## calculate AVAILABLE=`ls $LIGHTTPD_ACCESS_LOG_PATH` if [ "$AVAILABLE" = "$LIGHTTPD_ACCESS_LOG_PATH" ]; then TIME_NOW=`date` CODE_1xx="0" CODE_2xx="0" CODE_3xx="0" CODE_4xx="0" CODE_5xx="0" for i in 1 2 3 4 5; do TIME5=`date +%d/%b/%Y:%k:%M --date "$TIME_NOW -"$i"min"` CODE_1xx=$(( $CODE_1xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 1' | grep -c " "` )) CODE_2xx=$(( $CODE_2xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 2' | grep -c " "` )) CODE_3xx=$(( $CODE_3xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 3' | grep -c " "` )) CODE_4xx=$(( $CODE_4xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 4' | grep -c " "` )) CODE_5xx=$(( $CODE_5xx + `tail -n $LOG_ROWS $LIGHTTPD_ACCESS_LOG_PATH | grep "$TIME5" | grep 'HTTP/1.1" 5' | grep -c " "` )) done CODE_1xx=$(( $CODE_1xx / 5 )) CODE_2xx=$(( $CODE_2xx / 5 )) CODE_3xx=$(( $CODE_3xx / 5 )) CODE_4xx=$(( $CODE_4xx / 5 )) CODE_5xx=$(( $CODE_5xx / 5 )) echo "1xx.value "$CODE_1xx echo "2xx.value "$CODE_2xx echo "3xx.value "$CODE_3xx echo "4xx.value "$CODE_4xx echo "5xx.value "$CODE_5xx else echo "1xx.value U" echo "2xx.value U" echo "3xx.value U" echo "4xx.value U" echo "5xx.value U" fi If i run the script on local machine it runs perfectly: root@server1 /etc/munin/plugins # ll lrwxrwxrwx 1 root root 45 2011-12-19 15:23 lighttpd_statuscodes -> /usr/share/munin/plugins/lighttpd_statuscodes* root@server1 /etc/munin/plugins # ./lighttpd_statuscodes autoconf yes root@server1 /etc/munin/plugins # ./lighttpd_statuscodes config graph_title Lighhtpd Statuscodes graph_vlabel http-statuscodes / min graph_category lighttpd 1xx.label 1xx 2xx.label 2xx 3xx.label 3xx 4xx.label 4xx 5xx.label 5xx root@server1 /etc/munin/plugins #./lighttpd_statuscodes 1xx.value 0 2xx.value 5834 3xx.value 1892 4xx.value 0 5xx.value 0 But Munin shows no graph: http://s1.directupload.net/images/111219/3psgq3vb.jpg I have tested the Plugin from munin-server via telnet: root@munin-server /etc/munin/plugins/ # telnet 123.123.123.123 4949 Trying 123.123.123.123... Connected to 123.123.123.123. Escape character is '^]'. # munin node at server1.cluster1 fetch lighttpd_statuscodes 1xx.value U 2xx.value U 3xx.value U 4xx.value U 5xx.value U . Connection closed by foreign host. You can see in the script that value = U only printed, when the script can't check the lighttpd's access.log. But why can't script do it, when running via munin, and when running on local machine all is ok? Is there a bug in my bash-script? I have no Idea. Thanks for helping!

Read the article

WIM2VHD failing with "Cannot derive Volume GUID from mount point."

- by Jacob

I'm trying to use WIM2VHD according to the instructions on Scott Hanselman's blog post to create a Sysprepped VHD image to boot from. I've installed the WAIK, and I have my Windows 7 sources mounted as a virtual drive. When I try to run WIM2VHD like this: cscript WIM2VHD.wsf /wim:F:\sources\install.wim /sku:Ultimate /vhd:E:\WindowsSeven.vhd /size:30721 I get the following log: Log for WIM2VHD 6.1.7600.0 on 11/2/2009 at 10:51:18.16 Copyright (C) Microsoft Corporation. All rights reserved. MACHINE INFO: Build=7600 Platform=x86fre OS=Windows 7 Ultimate ServicePack= Version=6.1 BuildLab=win7_rtm BuildDate=090713-1255 Language=en-ZA INFO: Looking for IMAGEX.EXE... INFO: Looking for BCDBOOT.EXE... INFO: Looking for BCDEDIT.EXE... INFO: Looking for REG.EXE... INFO: Looking for DISKPART.EXE... INFO: Session key is E01E1ED7-C197-4814-BDE4-43B73E14FCC4 INFO: Inspecting the WIM... INFO: Configuring and formatting the VHD... ******************************************************************************* Error: 0: Cannot derive Volume GUID from mount point. ******************************************************************************* INFO: Unmounting the VHD due to error... WARNING: In order to help resolve the issue, temporary files have not been deleted. They are in: C:\Users\Jacob\AppData\Local\Temp\WIM2VHD.WSF\E01E1ED7-C197-4814-BDE4-43B73E14FCC4 *emphasized text*Summary: Errors: 1, Warnings: 1, Successes: 0 INFO: Done. Any ideas?

Read the article

Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

- by Emmel

I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

Read the article

Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

- by Emmel

I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

Read the article

Resize a RAID 1 volume on OS X Snow Leopard - how? (Note: software raid)

- by Emmel

I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OS X 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

Read the article

how to setup .ssh directory inside an encrypted volume on Mac OSX and still have public key logins?

- by Vitaly Kushner

I have my .ssh directory inside an encrypted sparse image. i.e. ~/.ssh is a symlink to /Volumes/VolumeName/.ssh The problem is that when I try to ssh into that machine using a public key I see the following error message in /var/log/secure.log: Authentication refused: bad ownership or modes for directory /Volumes Any way to solve this in a clean way? Update: The permissions on ~/.ssh and authorized_keys are right: > ls -ld ~ drwxr-xr-x+ 77 vitaly staff 2618 Mar 16 08:22 /Users/vitaly/ > ls -l ~/.ssh lrwxr-xr-x 1 vitaly staff 22 Mar 15 23:48 /Users/vitaly/.ssh@ -> /Volumes/Astrails/.ssh > ls -ld /Volumes/Astrails/.ssh drwx------ 3 vitaly staff 646 Mar 15 23:46 /Volumes/Astrails/.ssh/ > ls -ld /Volumes/Astrails/ drwx--x--x@ 18 vitaly staff 1360 Jan 12 22:05 /Volumes/Astrails// > ls -ld /Volumes/ drwxrwxrwt@ 5 root admin 170 Mar 15 20:38 /Volumes// error message sats the problem is with /Volumes, but I don't see the problem. Yes it is o+w but it is also +t which should be ok but apparently isn't. The problem is I can't change /Volumes permissions (or rather shouldn't) but I do want public key login to work. First I thought of mounting the image on other place then /Volumes, but it is automaunted on login by standard OSX mounting. I asked about it here: How to change disk image's default mount directory on osx The only answer I got is "you can't" ;) I could hack my way around, by writing some shellscript that will manually mounting volume at a non-standard location but it would be a gross hack, I'm still looking for a cleaner way to do what I need.

Read the article

Data Store/Volume disconnecting. How to resume copy of VMDK?

- by Serge

I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

Read the article

Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

- by Emmel

I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

Read the article

Why does this code generate an error? [closed]

- by user559601

Read the article

Improve Playback Using Enhancements in Windows Media Player 12

- by DigitalGeekery

Are you looking for ways to improve the playback of your media in Windows Media Player 12? We’ll show you how to do that by using the enhancements in WMP 12. If you are in Library mode, you’ll need to click the icon at the lower right to switch to Now Playing mode. Right-click anywhere in Media Player while in Now Playing mode, select Enhancements, and select any of the available options. You can switch between the individual enhancements by clicking the right and left buttons at the top left. Crossfading and Auto Volume Leveling The Auto Volume Leveling setting is just a simple toggle on and off. If your MP3 or WMA files have volume leveling information values. You can automatically add volume leveling information values to all files you add to your library by switching to Library view, going to Tools > Options, and selecting Add volume leveling information values for new files on the Library tab. Click OK when finished. Crossfading will gradually decrease the volume of the song that is ending (fade out) and increase volume of the song that is beginning. Click Turn on Crossfading and then click and drag the slider left or right change the amount of overlap between tracks. Graphic Equalizer The graphic equalizer is toggled on and off by clicking Turn on / Turn off at the top left. You can select pre-defined equalizer settings by music genre by clicking the Default list. The radio buttons on the left allow you to move the sliders individually, in a loose group or a tight group. You can always return to the default settings by clicking Reset. Play Speed Settings Choose a pre-defined settings by clicking Slow, Normal, or Fast. Uncheck the Snap slider to common speeds the move the slider right and left to your desired speed. If nothing else, these settings provide a little fun and amusement. Quiet Mode Quiet mode will level out any sharp volume highs and lows within a single track. Simply toggle the setting on or off and select whether you prefer Medium difference or Little difference by selecting one of the radio buttons. SRS WOW effects SRS WOW effects enhance low-frequency and stereo sound performance. Click Turn on to enable the TruBass and WOW Effect sliders. You can also optimize for your speaker type. Click to switch between Regular, Large, and Headphones. Video Settings Video Settings allow you to adjust the Hue, Brightness, Saturation, and Contrast. You can also adjust the zoom settings by clicking Select video zoom settings. Dolby Digital Settings Choose between Normal, Night, and Theater settings to adjust the audio for Dolby Digital content. This setting will only effect media with Dolby Digital sound. Looking for more ways to improve your media experience in WMP 12? Check out how to update metadata and cover art and how to share media with other Windows 7 computers on your home network. Similar Articles Productive Geek Tips Fixing When Windows Media Player Library Won’t Let You Add FilesInstall and Use the VLC Media Player on Ubuntu LinuxHow To Rip a Music CD in Windows 7 Media CenterStream Media from Windows 7 to XP with VLC Media PlayerInstalling Windows Media Player Plugin for Firefox TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Acronis Online Backup DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows Check these Awesome Chrome Add-ons iFixit Offers Gadget Repair Manuals Online Vista style sidebar for Windows 7 Create Nice Charts With These Web Based Tools Track Daily Goals With 42Goals Video Toolbox is a Superb Online Video Editor

Read the article

How to use jQuery to assign a class to only one radio button in a group when user clicks on it?

- by xraminx

I have the following markup. I would like to add class_A to <p class="subitem-text"> (that holds the radio button and the label) when user clicks on the <input> or <label>. If user clicks some other radio-button/label in the same group, I would like to add class_A to this radio-button's parent paragraph and remove class_A from any other paragraph that hold radio-buttons/labels in that group. Effectively, in each <li>, only one <p class="subitem-text"> should have class_A added to it. Is there a jQuery plug-in that does this? Or is there a simple trick that can do this? <ul> <li> <div class="myitem-wrapper" id="10"> <div class="myitem clearfix"> <span class="number">1</span> <div class="item-text">Some text here </div> </div> <p class="subitem-text"> <input type="radio" name="10" value="15" id="99"> <label for="99">First subitem </label> </p> <p class="subitem-text"> <input type="radio" name="10" value="77" id="21"> <label for="21">Second subitem</label> </p> </div> </li> <li> <div class="myitem-wrapper" id="11"> <div class="myitem clearfix"> <span class="number">2</span> <div class="item-text">Some other text here ... </div> </div> <p class="subitem-text"> <input type="radio" name="11" value="32" id="201"> <label for="201">First subitem ... </label> </p> <p class="subitem-text"> <input type="radio" name="11" value="68" id="205"> <label for="205">Second subitem ...</label> </p> <p class="subitem-text"> <input type="radio" name="11" value="160" id="206"> <label for="206">Third subitem ...</label> </p> </div> </li>

Search Results

Search found 7632 results on 306 pages for 'volume label'.

Page 48/306 | < Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55 | Next Page >

- by Mark

- by g0lem

- by Vinayak Agarwal

- by srikanth rongali

- by mlvljr

- by suchita

- by Blankman

- by ryan

- by Mojiiz Alamode

- by endolith

- by juanlarios

- by ScottGu

- by user3563124

- by Lihnjo

- by FTV Admin

- by Jacob

- by Emmel

- by Emmel

- by Emmel

- by Vitaly Kushner

- by Serge

- by Emmel

- by user559601

- by DigitalGeekery

- by xraminx

< Previous Page | 44 45 46 47 48 49 50 51 52 53 54 55 | Next Page >