Search Results

Search found 34836 results on 1394 pages for 'off the shelf software'.

Page 480/1394 | < Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• Changing externally visible IP on a multi-IP router?

  - by AlternateZ

  I work at a public library and I'm trying to configure OCLC's EzProxy software. I've run into a problem and I think it's related to our network config. I'm punching above my weight here a little so I need some help. I think I'm trying to configure a 1:1 NAT, but not sure how or if our hardware supports it. The EzProxy machine is on an internet line which supports multiple external IPs. Our router is a Billion BiGuard30. There's another server on this line, let's say its IP is x.x.x.9. The EzProxy machine is x.x.x.11 I've set up port forwarding from x.x.x.11 on the http ports to the EzProxy machine. Trying to browse to x.x.x.11 from an external PC works fine - we get to the EzProxy page we are serving. However, if we go to something like WhatIsMyIP from the EzProxy machine, it says that its IP is x.x.x.9. This causes problems with our user authentication software. How do we make the rest of the internet see that the machine is x.x.x.11? There doesnt seem to be any "outbound port forwarding" on the Billion router, nor is there any "1:1 NAT" options in its config webpage. The EzProxy machine is running Ubuntu 12.04, if that helps.

  Read the article

• NGINX SSI Not working

  - by Mike Kelly

  I'm having trouble getting SSI to work on NGINX. You can see the problem if you hit http://www.bakerycamp.com/test.shtml. Here is the contents of that file: <!--# echo hi --> If you hit this in a browser, you see the SSI directive in the content - so apparently NGINX is not interpreting the SSI directive. My NGINX config file looks like this: server { listen 80; server_name bakerycamp.com www.bakerycamp.com; access_log /var/log/nginx/bakerycamp.access.log; index index.html; root /home/bakerycamp.com; location / { ssi on; } # Deny access to all hidden files and folders location ~ /\. { access_log off; log_not_found off; deny all; } } I did not build NGINX from sources but installed it using apt-get. I assume it has the SSI module (since that is default) but perhaps not? Should I just bite the bullet and rebuild from sources? Is there anyway to tell if the installed NGINX supports SSI and my config is just wrong?

  Read the article

• DIY NAS - links for Instructions

  - by Kaushik Gopal

  Good folk of SU, I'm planning to build a NAS (Network Access Storage). I'm planning to do it cheap (:read Old PC Config + Open source software). I was looking for good DIY links . Before you shoot this down as a Repost, I'm only looking for good links containing detailed instructions for setting up a NAS. I did a fair bit of searching and found these links (so please suggest others. While these links are great they delve more on the hardware side, i'm looking for more instructions in the software side). For the sake of the interwebs: Ubuntu: http://snarfquest.com/wiki/index.php/Setting_up_a_Home_NAS http://www.smallnetbuilder.com/content/view/27962/77/ http://jonpeck.blogspot.com/2006/11/how-to-configure-80-fileserver-in-45.html FreeNAS http://www.smallbusinesscomputing.com/webmaster/article.php/3719706 http://www.codeproject.com/KB/system/homemade_nas.aspxhttp://www.codeproject.com/KB/system/homemade_nas.aspx There was one at rubbervir.us that everyone points to, but apparently the site has gone down. A couple of other queries: Is Printer/Scanner sharing a possibility with NAS devices? Many talk of torrent support with NAS Devices, a little more light on this? Does this mean, an auto download of torrent through a feed into NAS, or just support for storing Torrent download files onto the NAS(don't see the difference between the latter and a normal file tranfer)

  Read the article

• E-mail hosting provider that can set up aliases with wildcards

  - by Richard Downer

  I am looking for an e-mail hosting provider that allow e-mail aliases containing wildcards. In more detail: I own my own domain. I want an e-mail hosting provider to manager e-mail for my domain. Now, to help deal with spam, I often give different e-mail addresses to different organisations. These e-mail addresses always start with the same prefix, but then differ. So, for example, I might give out these e-mail addresses: [email protected] [email protected] [email protected] I want to be able to go to the e-mail provider's control panel and set up an e-mail alias like this: [email protected] -- bounce/discard (because this address has been sold to spammers) joe-*@sample.com -- redirect to [email protected] What's I don't want to do is either have to set up every single e-mail address individually (because I make them up whenever I need them), nor do I want to have a general catch-all for any unrecognised address in my domain (because I don't want to be carpet-bombed with spam when a spammer runs a dictionary attack against my domain name.) Although this seems like a useful feature to have, it seems to be a little-known feature and I've not seen anybody advertise this feature. My current hosting provider offer this but I want to move away from them, so I need another provider that will continue to work with all the e-mail addresses I've been using for years. Alternatively, I could use mail server software that runs on Windows - I have seen some commercial packages offering this feature but they cost more than I can afford - are there any suggestions for low-cost software packages?

  Read the article

• How can I get MySQL 5.5 to log warnings to one of the log files?

  - by Wodin

  I have found various things that say that you can log warnings to the MySQL error log, but I have not been able to actually make it happen. I do have the error log working, and MySQL prints stuff to it on startup and shutdown and occasionally at other times, but if I e.g. SELECT CAST('123' AS DATE); and then SHOW WARNINGS; I can see the warning, but it does not show up in any logs. I've also tried enabling the general log and the slow query log, but these don't show the warnings either. I've tried with log_warnings = 1 and log_warnings = 2, but still no warnings are logged. What am I doing wrong? mysql> show variables like '%error%'; +--------------------+--------------------------+ | Variable_name | Value | +--------------------+--------------------------+ | error_count | 0 | | log_error | /var/log/mysql/mysql.err | | max_connect_errors | 10 | | max_error_count | 1024 | | slave_skip_errors | OFF | +--------------------+--------------------------+ mysql> show variables like '%warn%'; +---------------+-------+ | Variable_name | Value | +---------------+-------+ | log_warnings | 1 | | sql_warnings | OFF | | warning_count | 0 | +---------------+-------+ 3 rows in set (0.06 sec) mysql> show variables like '%log%'; +-----------------------------------------+-------------------------------+ | Variable_name | Value | +-----------------------------------------+-------------------------------+ ... | general_log | ON | | general_log_file | /var/log/mysql/general.log | ... | log | ON | ... | log_error | /var/log/mysql/mysql.err | | log_output | FILE | | log_queries_not_using_indexes | ON | ... | log_warnings | 1 | ... | slow_query_log | ON | | slow_query_log_file | /var/log/mysql/mysql-slow.log | ... +-----------------------------------------+-------------------------------+ Edit: mysql> show global status like 'Aborted%'; +------------------+-------+ | Variable_name | Value | +------------------+-------+ | Aborted_clients | 24 | | Aborted_connects | 15 | +------------------+-------+ 2 rows in set (0.08 sec) Edit: Clarification: I do get [Warning] Aborted connection 1 to db... and [Warning] Access denied for user... messages logged, but not the warnings that you can see via SHOW WARNINGS after e.g. inserting something or running LOAD DATA INFILE... which is what I'm looking for.

  Read the article

• OCZ Vertex 3 SSD boot failure

  - by Col Zero

  Ok, so I just purchased and received a 120GB OCZ Vertex 3. I had Windows 7 on an .ISO file on my computer. I formatted a USB stick and configured it to be read as a CD so that I could install windows onto my SSD from it. I started my comp, had the boot priority set to my USB, starting installing windows 7 to my SSD. And out of no where (I wasn't watching) my computer restarted and it brought me back to the beginning of the Windows 7 set-up. So I turned my computer off and booted it up from the SSD to see if it had installed onto the SSD. The first 2 attempts I had a disk boot failure. So I plugged my hard drive back in, started my computer, turned it off, plugged the SSD back in (literally) and it booted up fine/ Finalized windows got internet set up, and Windows had updates that required a restart. So I restarted and had another disk boot failure. Now I have a disk boot failure every time I try to start my computer up through my SSD. Extra Info: My SSD has never been able to be detected in my BIOS unless my Hard Drive was unplugged (eve then my BIOS didn't always detect it). MY SSD wasn't detected in my BIOS the first and only time it successfully booted up. My SSD literally boots up successfully randomly (only once unfortunately) and is detected in my BIOS randomly. I've tried switching cords etc and nothing has worked. I just want to get this damn thing running so I can see whats its like. I finally found a way to get the OS on this sucker and now it won't even boot up. Any help appreciated

  Read the article

• Ripping a home video VCD on Linux or Windows with VLC or otherwise

  - by user259774

  I have a VCD with 22 minutes of video on it. I would like to retain this footage and throw away the VCD. I can play the whole thing with VLC ("open disc - vcd - /dev/sr0 - play"): all 22 minutes of the main track. I don't believe there's any other content aside from the main track. I can seek to anywhere I want to within the 22 minute track. If I mount /dev/sr0 /media/vcd and then try to copy the only file from the MPEGAV folder, I get an I/O error, with an empty destination file. VLC has a "convert" option in addition to "play". When I use this I actually get a good OGG file back, after it runs through the video in painful real-time. I guess it dubs it frame-by-frame. But the file is only 10 minutes long, leaving 12 minutes off of the track. Handbrake doesn't detect it's track titles, unfortunately. I don't know if I should start getting involved with GNU ddrescue or if it's because VCDs somehow encode their data sectors differently. Anyway, I'm in way over my head and if anyone knows how I could get that video track off the thing, feel free to share! Edit: I should note that I also have access to a Windows computer

  Read the article

• Redmine install not working and displaying directory contents - Ubuntu 10.04

  - by Casey Flynn

  I've gone through the steps to set up and install the redmine project tracking web app on my VPS with Apache2 but I'm running into a situation where instead of displaying the redmine app, I just see the directory contents: Does anyone know what could be the problem? I'm not sure what other files might be of use to diagnose what's going on. Thanks! # # Based upon the NCSA server configuration files originally by Rob McCool. # # This is the main Apache server configuration file. It contains the # configuration directives that give the server its instructions. # See http://httpd.apache.org/docs/2.2/ for detailed information about # the directives. # # Do NOT simply read the instructions in here without understanding # what they do. They're here only as hints or reminders. If you are unsure # consult the online docs. You have been warned. # # The configuration directives are grouped into three basic sections: # 1. Directives that control the operation of the Apache server process as a # whole (the 'global environment'). # 2. Directives that define the parameters of the 'main' or 'default' server, # which responds to requests that aren't handled by a virtual host. # These directives also provide default values for the settings # of all virtual hosts. # 3. Settings for virtual hosts, which allow Web requests to be sent to # different IP addresses or hostnames and have them handled by the # same Apache server process. # # Configuration and logfile names: If the filenames you specify for many # of the server's control files begin with "/" (or "drive:/" for Win32), the # server will use that explicit path. If the filenames do *not* begin # with "/", the value of ServerRoot is prepended -- so "/var/log/apache2/foo.log" # with ServerRoot set to "" will be interpreted by the # server as "//var/log/apache2/foo.log". # ### Section 1: Global Environment # # The directives in this section affect the overall operation of Apache, # such as the number of concurrent requests it can handle or where it # can find its configuration files. # # # ServerRoot: The top of the directory tree under which the server's # configuration, error, and log files are kept. # # NOTE! If you intend to place this on an NFS (or otherwise network) # mounted filesystem then please read the LockFile documentation (available # at <URL:http://httpd.apache.org/docs-2.1/mod/mpm_common.html#lockfile>); # you will save yourself a lot of trouble. # # Do NOT add a slash at the end of the directory path. # ServerRoot "/etc/apache2" # # The accept serialization lock file MUST BE STORED ON A LOCAL DISK. # #<IfModule !mpm_winnt.c> #<IfModule !mpm_netware.c> LockFile /var/lock/apache2/accept.lock #</IfModule> #</IfModule> # # PidFile: The file in which the server should record its process # identification number when it starts. # This needs to be set in /etc/apache2/envvars # PidFile ${APACHE_PID_FILE} # # Timeout: The number of seconds before receives and sends time out. # Timeout 300 # # KeepAlive: Whether or not to allow persistent connections (more than # one request per connection). Set to "Off" to deactivate. # KeepAlive On # # MaxKeepAliveRequests: The maximum number of requests to allow # during a persistent connection. Set to 0 to allow an unlimited amount. # We recommend you leave this number high, for maximum performance. # MaxKeepAliveRequests 100 # # KeepAliveTimeout: Number of seconds to wait for the next request from the # same client on the same connection. # KeepAliveTimeout 15 ## ## Server-Pool Size Regulation (MPM specific) ## # prefork MPM # StartServers: number of server processes to start # MinSpareServers: minimum number of server processes which are kept spare # MaxSpareServers: maximum number of server processes which are kept spare # MaxClients: maximum number of server processes allowed to start # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # worker MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> # event MPM # StartServers: initial number of server processes to start # MaxClients: maximum number of simultaneous client connections # MinSpareThreads: minimum number of worker threads which are kept spare # MaxSpareThreads: maximum number of worker threads which are kept spare # ThreadsPerChild: constant number of worker threads in each server process # MaxRequestsPerChild: maximum number of requests a server process serves <IfModule mpm_event_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> # These need to be set in /etc/apache2/envvars User ${APACHE_RUN_USER} Group ${APACHE_RUN_GROUP} # # AccessFileName: The name of the file to look for in each directory # for additional configuration directives. See also the AllowOverride # directive. # AccessFileName .htaccess # # The following lines prevent .htaccess and .htpasswd files from being # viewed by Web clients. # <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> # # DefaultType is the default MIME type the server will use for a document # if it cannot otherwise determine one, such as from filename extensions. # If your server contains mostly text or HTML documents, "text/plain" is # a good value. If most of your content is binary, such as applications # or images, you may want to use "application/octet-stream" instead to # keep browsers from trying to display binary files as though they are # text. # DefaultType text/plain # # HostnameLookups: Log the names of clients or just their IP addresses # e.g., www.apache.org (on) or 204.62.129.132 (off). # The default is off because it'd be overall better for the net if people # had to knowingly turn this feature on, since enabling it means that # each client request will result in AT LEAST one lookup request to the # nameserver. # HostnameLookups Off # ErrorLog: The location of the error log file. # If you do not specify an ErrorLog directive within a <VirtualHost> # container, error messages relating to that virtual host will be # logged here. If you *do* define an error logfile for a <VirtualHost> # container, that host's errors will be logged there and not here. # ErrorLog /var/log/apache2/error.log # # LogLevel: Control the number of messages logged to the error_log. # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. # LogLevel warn # Include module configuration: Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf # Include all the user configurations: Include /etc/apache2/httpd.conf # Include ports listing Include /etc/apache2/ports.conf # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent # # Define an access log for VirtualHosts that don't define their own logfile CustomLog /var/log/apache2/other_vhosts_access.log vhost_combined # Include of directories ignores editors' and dpkg's backup files, # see README.Debian for details. # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ # Enable fastcgi for .fcgi files # (If you're using a distro package for mod_fcgi, something like # this is probably already present) #<IfModule mod_fcgid.c> # AddHandler fastcgi-script .fcgi # FastCgiIpcDir /var/lib/apache2/fastcgi #</IfModule> LoadModule fcgid_module /usr/lib/apache2/modules/mod_fcgid.so LoadModule passenger_module /var/lib/gems/1.8/gems/passenger-3.0.7/ext/apache2/mod_passenger.so PassengerRoot /var/lib/gems/1.8/gems/passenger-3.0.7 PassengerRuby /usr/bin/ruby1.8 ServerName demo and my vhosts file #No DNS server, default ip address v-host #domain: none #public: /home/casey/public_html/app/ <VirtualHost *:80> ServerAdmin webmaster@localhost # ScriptAlias /redmine /home/casey/public_html/app/redmine/dispatch.fcgi DirectoryIndex index.html DocumentRoot /home/casey/public_html/app/public <Directory "/home/casey/trac/htdocs"> Order allow,deny Allow from all </Directory> <Directory /var/www/redmine> RailsBaseURI /redmine PassengerResolveSymlinksInDocumentRoot on </Directory> # <Directory /> # Options FollowSymLinks # AllowOverride None # </Directory> # <Directory /var/www/> # Options Indexes FollowSymLinks MultiViews # AllowOverride None # Order allow,deny # allow from all # </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /home/casey/public_html/app/log/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel debug CustomLog /home/casey/public_html/app/log/access.log combined # Alias /doc/ "/usr/share/doc/" # <Directory "/usr/share/doc/"> # Options Indexes MultiViews FollowSymLinks # AllowOverride None # Order deny,allow # Deny from all # Allow from 127.0.0.0/255.0.0.0 ::1/128 # </Directory> </VirtualHost>

  Read the article

• Can I use this power supply + case combination without causing problems?

  - by evan

  I am putting together a computer with a Antec P180 case and a Thermaltake TR2 RX 650 W power supply. The problem is that the Antec P180 case has a separate compartment for the power supply. With an opening for the on/off switch + ac connector to one side, a wall with a small hole for cables to route through on top, a wall on the bottom, and on the other side a fan which pushes air from the hard drive compartment to the power supply compartment. I think the design of the case assumes the power supplies fan is on the side next to the on/off switch, but the fan on the power supply I have is on top, which makes me worry about overheating the power supply. There is about half an inch between the top of the power supply and the wall and the other fan should keep air flowing to push out the air that the power supply pushes upwards. Do you think this setup should work, or should I go get another power supply? Thanks!! PS: This computer will be running an Ubuntu server, so it will always be on, but the rest of the components shouldn't be generating as much heat as they would on say a gaming machine.

  Read the article

• HP Procurve Issue Passing Multiple VLANs over a link

  - by MichaelRwat

  Just to start off with I am a Cisco guy that got placed into an HP project. Basic topology overview from outside in: ASA 5505 with two Ethernet connections to a 2910-24 port switch. This switch is then (Cisco Trunking) to a 2626 switch passing vlan (1 untagged and 100 tagged)between them. I created SVI's on each of the switches for both VLAN's for testing purposes. I can not get vlan 100 to pass across this link. I also have trunks configured to AP's off of the switch and can not ping the vlan 100 BVI on the AP's but can reach the vlan 1 BVI. Port 25 on Access layer (2626) connects (trunks) with port A1 of 2610. STP is not running at all on any switch (this is not my network I can't change this nor did I design this) Distribution Sw: MP1-0# show run ip default-gateway 10.100.100.100 vlan 1 name "DATA" untagged 1-22,24-A1,B1 ip address 10.100.100.6 255.255.255.0 no untagged 23 exit vlan 100 name "GUEST" untagged 23 tagged 24-A1 ip address 10.100.102.6 255.255.255.0 exit Access Sw: ip default-gateway 10.100.100.100 vlan 1 name "DEFAULT_VLAN" untagged 1-26 ip address 10.100.100.5 255.255.255.0 exit vlan 100 name "GUEST" ip address 10.100.102.5 255.255.255.0 tagged 15,25 exitt From the ASA I can ping the vlan 100 address of the 2610 but not the 2626 (10.100.102.6)[Not passing the "trunk"] If I plug into an access port vlan 100 of the 2626 I can ping the SVI for vlan 100 as intended. I can not ping across the "trunk" over vlan 100 but I can across vlan 1. There may be something obvious I'm missing but please review my configuration and thank you for the assistance.

  Read the article

• Keynote presentation in conjunction with other app?

  - by Sören Kuklau

  The short version: I'd like to tell Apple Keynote to switch to a specific app (never leaving full-screen mode) before a certain slide appears, then display that slide as soon as I switch back. Some more details: I'm going to show off five major improvements in an upcoming release of our app. I want one slide highlighting the feature, then one or two showing some details, perhaps with screenshots. After that, so people get a better impression of what I'm talking about, I'll show it off live — to do this, I have to switch to a VM or remote session (since this is a Windows app). Then, I'd like to switch back and go to the next feature. I.e., it would be similar to Apple's "Demo" slides in a cursive font, except not with a different screen, or different computer. It's this switching back and forth that I want to make smooth, just to wow the audience a little. Can I perhaps do a "special" slide in Keynote that tells it to run an AppleScript? Better yet, to switch to an app, and wait until I switch back, and then automatically advance to the next slide?

  Read the article

• Jira access with AJP-Proxy

  - by user60869

  I want to Configure the Jira-Acces over APJ-Proxy. I proceeded as follows (Following this howto: http://confluence.atlassian.com/display/JIRA/Configuring+Apache+Reverse+Proxy+Using+the+AJP+Protocol) : 1) In the server.xml I activate the AJP: 2) Edit VHOST Konfiguration: # Load Proxy-Modules LoadModule proxy_module /usr/lib/apache2/modules/mod_proxy.so LoadModule proxy_http_module /usr/lib/apache2/modules/mod_proxy_http.so # Load AJP-Modules LoadModule proxy_ajp_module /usr/lib/apache2/modules/mod_proxy_ajp.so # Proxy Configuration <IfModule proxy_http_module> ProxyRequests Off ProxyPreserveHost On # Basic AuthType configuration <Proxy *> AuthType Basic AuthName Bamboo-Server AuthUserFile /var/www/userdb Require valid-user AddDefaultCharset off Order deny,allow Deny from all Allow from 192.168.0.1 satisfy any </Proxy> ProxyPass /bamboo http://localhost:8085/bamboo ProxyPassReverse /bamboo http://localhost:8085/bamboo ProxyPass /jira ajp://localhost:8009/ ProxyPassReverse /jira ajp://localhost:8009/ </IfModule> EDIT: In the logs if found follow: //localhost:8080/ [Fri Nov 19 14:51:13 2010] [debug] proxy_util.c(1819): proxy: worker ajp://localhost:8080/ already initialized [Fri Nov 19 14:51:13 2010] [debug] proxy_util.c(1913): proxy: initialized single connection worker 1 in child 5578 for (localhost) [Fri Nov 19 14:51:32 2010] [error] ajp_read_header: ajp_ilink_receive failed [Fri Nov 19 14:51:32 2010] [error] (120006)APR does not understand this error code: proxy: read response failed from (null) (localhost) [Fri Nov 19 14:51:32 2010] [debug] proxy_util.c(2008): proxy: AJP: has released connection for (localhost) [Fri Nov 19 14:51:32 2010] [debug] mod_deflate.c(615): [client xx.xx.xx.xx Zlib: Compressed 468 to 320 : URL /jira But It dosen´t work. Somebody have an idea?

  Read the article

• Dual Xeon Server voltages are low

  - by Mindflux

  I've got a whitebox server running CentOS 5.7. It's a Dual Xeon 5620, 24GB of RAM. The mainboard is a SuperMicro X8DT6-F and the chassis is a SC825TQ-R720LPB. Dual 720W Power supplies. We had a big power outage a couple weeks back that took down everything, I don't have any pre-power outage figures for this server, and the only reason I noticed these is because when I was bringing up the servers I was checking them out with more scrutiny than usual. http://i.imgur.com/rSjiw.png (Image of voltage readings) As you can see, CPU1 DIMM is low, +3.3V is high, 3.3VSB is high, +5v is high, +12v is REAL LOW (out of normal 5% (plus/minus))... and VBAT is off the charts. With my whitebox VAR we've tried the following: Swap out PSU with another server I have with the same PSUs. Try different power cord Update BMC/IPMI firmware in case readings were wrong (They aren't) Update BIOS Try different PDU Try a different outlet and/or circuit Replaced Voltage Regulator Unit At this point, the only thing we haven't done, seemingly is replace the mainboard.. which is what the next step will be unless something else shines some light on the situation. I should mention the system is rock solid otherwise which is a surprise given the 12v voltage is that far off.

  Read the article

• Kernel panic while loading Mac OS X on VMWare

  - by Vladimir Gritsenko

  I'm trying to run Mac OS X 10.6.3 on VMWare 7.1 from within Windows 7 64 bit. Trying to run the OS X doesn't work - shortly after booting VMWare announces the machine's death with this pop-up message: The CPU has been disabled by the guest operating system. You will need to power off or reset the virtual machine at this point. The console has a more interesting announcement: The real-time clock was not properly initialized on your system! With a dump of the detected CPU speed (~2.9 GHz), FSB (~94 MHz) and bus ratio (31). Somehow, the code that panics is documented in an accidental .diff file here. Apparently, it commits seppuku if the bus ratio is greater than 30. I underclocked my E6500 to a slower speed, but this apparently didn't make any difference. I can think of two possibilities right now: The CPU info being read is constant, and defines the maximum ability of the CPU. In which case it appears I'm screwed. VMWare presents its own CPU info to the machine, which I can perhaps somehow change. If so, how? If these sound completely off, that's because I'm a real newbie in these matters. Here's hoping you guys can show me the light :-)

  Read the article

• How to add another application to apache?

  - by Jader Dias

  I was following the Zabbix installation tutorial for Ubuntu and it requested that I added a file /etc/apache2/sites-enabled/000-default containing Alias /zabbix /home/zabbix/public_html/ <Directory /home/zabbix/public_html> AllowOverride FileInfo AuthConfig Limit Indexes Options MultiViews Indexes SymLinksIfOwnerMatch IncludesNoExec <Limit GET POST OPTIONS PROPFIND> Order allow,deny Allow from all </Limit> <LimitExcept GET POST OPTIONS PROPFIND> Order deny,allow Deny from all </LimitExcept> </Directory> But I already have /etc/apache2/sites-enabled/railsapp NameVirtualHost *:80 NameVirtualHost *:443 <VirtualHost *:80> UseCanonicalName Off Include /etc/apache2/conf/railsapp.conf </VirtualHost> <VirtualHost *:443> SSLEngine on SSLCertificateFile /etc/ssl/certs/cert.pem Include /etc/apache2/conf/railsapp.conf RequestHeader set X_FORWARDED_PROTO 'https' </VirtualHost> and /etc/apache2/sites-enabled/mercurial NameVirtualHost *:8080 <VirtualHost *:8080> UseCanonicalName Off ServerAdmin webmaster@localhost AddHandler cgi-script .cgi ScriptAliasMatch ^(.*) /usr/lib/cgi-bin/hgwebdir.cgi/$1 </VirtualHost> I think that it is because of the already existing virtual hosts that my I can't access the zabbix page. How to circumvent this?

  Read the article

• Trouble with local id / remote id configuration of VPN

  - by Lynn Owens

  I have a NetGear UTM firewall and a Windows machine running NetGear's VPN client. The Windows machine I can put on the UTM network and take off of it. When I am cabled into the local (internal) the following configuration works: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: User FQDN: utm_remote1.com Client: Local Id: DNS: utm_remote1.com Remote Id: (The UTM's WAN IP address) Gateway authentication: preshared key Policy remote endpoint: FQDN: utm_remote1.com But when I'm off the UTM's internal local network and simply coming in from the internet, this does not work. It simply repeats SEND phase 1 before giving up. Since I know that the UTM WAN IP is accessible from both inside and outside the network, I figured the problem was with the Client local id. So, I tried the following: UTM: Local Id: Local Wan IP: (The UTM's WAN IP address) Remote Id: (A DN of a self-signed certificate I created for the client and uploaded into the UTM certificates) Client: Local Id: (The DN of the aforementioned self signed cert) Remote Id: (The UTM's WAN IP address) Gateway authentication: (the aforementioned self signed cert) Policy remote end point: ... er, ... my choices are IP and FQDN.... Not sure what to put here No matter what I've tried, it just keeps repeating the SEND phase 1. Any ideas?

  Read the article

• Windows file locks allowing multiple users to write to open file over network

  - by JPbuntu

  I have 6 windows computers (xp,vista,7) that need to access a samba share (Ubuntu 12.04). I am trying to make it so only one client can open a file at a given time. I thought this was pretty standard behavior of file locks, but I can't get it to work. The way it is right now a file can be open by two users, and changed and saved by either one of them. The last file saved overwrites what ever changes the other user made. At first I thought this was a Samba configuration problem, but I get this behavior even between two windows machines. So far I have only tested: Windows Xp Windows Vista Windows XP Samba << Windows Vista and both give the same behavior. When I tested the Samba configuration, I had set strict locking = yes and get errors logged like this: close_remove_share_mode: Could not get share mode lock for file _prod/part_number_list_COPY.xlsx Eventually all of the files are going to be moved onto the Samba share, so that is the configuration I am most concerned about fixing. Any ideas? Thanks in advance. EDIT: I tested an excel file again, and it is now working properly in both above mentioned cases, I am also no longer getting the above mentioned error. I don't know what happened, perhaps a restart fixed it? (also works with strict locking = no) Although I still need to find a solution for the CAD/CAM files we use, the software is Vector and it does not seem to be using file locks. Is there any software that I can use to manage these files, so two people can't open/edit them at a time? Maybe a windows application that forces file locks? Or a dirt simple version control system? (the only ones I have seen at are too complicated for our needs).

  Read the article

• Apache mod_rewrite and mod_vhost_alias Virtual Hosts and %1

  - by Matt Wall

  I have put the main bits of my httpd.conf down below. I am using %1 to get the host field so I can dynamically add vhosts by just creating dns/folders. One problem is I need to reference this: HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" In Apache when I try say to do this: http://test.domain.com/hds-vod/myfile.mp4.f4m it sees the %1 in the logs, and fails. Apache gives me this: [error] mod_jithttp [403]: No access to D:/Content/%1/DefaultContent/eve.mp4 What I'm looking for is the D:/Content/%1/DefaultContent/eve.mp4 to become D:/Content/test/DefaultContent/eve.mp4 Anyone have any useful resources / hints etc. to help me? Meanwhile my Google searching continues...! Listen 80 ServerName main1.rtmphost.com AccessFileName .htaccess ServerSignature On UseCanonicalName Off HostnameLookups Off Timeout 120 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 15 RewriteLogLevel 0 RewriteLog logs/rewrite.log DocumentRoot D:/Content LoadModule vhost_alias_module modules/mod_vhost_alias.so VirtualDocumentRoot "D:/Content/%1" RewriteEngine On <Directory /> Options None AllowOverride None Order allow,deny Allow from all Satisfy all </Directory> <IfModule f4fhttp_module> <Location /vod> HttpStreamingEnabled true HttpStreamingContentPath "D:/FMSApps/%1" Options FollowSymLinks </Location> Redirect 301 /live/events/livepkgr/events /hds-live/livepkgr <Location /hds-live> HttpStreamingEnabled true HttpStreamingLiveEventPath "D:/FMSApps/%1" HttpStreamingContentPath "D:/FMSApps/%1" HttpStreamingF4MMaxAge 2 HttpStreamingBootstrapMaxAge 2 HttpStreamingFragMaxAge -1 Options FollowSymLinks </Location> </IfModule>

  Read the article

• Computer does not switch on after power outage

  - by cristian

  VOLTAGE DROP OFF FOR PC does not restart The other day my pc was turned off due to power outage. Since that time the computer would not turn on again, no sign of life, it seems dead. I did several tests, changed the power outlet and disconnect the wires ... also I have reseated the cards ... but the result is that nothing changes. What can I do? Could there may be damage to the hardware due to the power outage? Note: the voltage drop is not due to a lightning storm and so is not due to damaged components (burnt card etc ...) Original Text: l'altro giorno il pc mi si è spento improvvisamente per calo tensione.... da quel momento non si è piu' riacceso...nessun segnale di vita...sembra proprio morto. Ho fatto diverse prove, cambio presa di alimentazione, scollegare i fili...insomma ho "mischiato le carte"...ma il risultato è che non cambia nulla. Cosa posso fare? cosa puo' essere successo? Possono esserci danni hardware per il calo di tensione? NB: il calo di tensione non e' dovuto ad una saetta e quindi escluderei danni causa temporale (bruciature scheda ecc...) Grazie mille

  Read the article

• Virtual bridged networking with VLAN, could not ping

  - by v.yegy

  I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

  Read the article

• Is TrueCrypt truly safe?

  - by Alfred

  Hi. I have been using TrueCrypt for a long time now. However, someone pointed me to a link that described the problems with the license. IANAL and so it really didn't make much sense to me, however I wanted my encryption software to be open source - not because I could hack into it but because I could trust it. Some of the issues with it I have noticed: There is no VCS for the source code. Is this OK? There are no change logs. The forums are a bad place to be. They ban even if you ask a genuine question. Who really owns TrueCrypt? There were some reports of tinkering with the md5 checksums. To be honest, the only reason why I used TrueCrypt was because it was open source. But however, somethings are just not right. Has anyone ever validated the security of TrueCrypt? Should I really be worried? Yes I am paranoid; if I use an encryption software, I trust it with all my life. If all my concerns are genuine, is there any other open source alternative to TrueCrypt?

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

• HTPC/DVR computer won't go into standby

  - by Robert

  When I select Start-Turn off computer-Standby the 'turn off computer' option window closes, and then nothing else happens. I can start new applications, and Windows acts like I never selected standby. I ran it for several hours after that. If I have a TV program scheduled to record when I select standby I get a window (the Pinnacle TV software) asking if I'm sure, there are programs scheduled to record - and the computer just keeps running after I select yes, never going into standby. I added that detail as it shows the standby process is starting. [This problem also happens if a TV program is not scheduled, so the scheduler task in not running/in memory. This problem happens regardless of whether I'm not watching TV. This problem happens regardless of whether Media Center is running (it usually isn't, I'm using Pinnacle to watch TV).] I looked at "How to troubleshoot hibernation and standby issues in Windows XP" http://support.microsoft.com/kb/907477 - ACPI is enabled, and "standby" is an option in "Power Options Properties." So it appears to be setup correctly. Windows XP SP3 Media Center Edition, all current updates installed.

  Read the article

• DisableCrossAccountCopy not working on some Outlook installs, working on others, both going against Exchange

  - by MikeBaz

  As part of a mail migration project from one Exchange organization to another, we need to be able to prevent users from moving/copying messages between their accounts in each organization. (Yes, users will think this is evil; no, it's not my decision; yes, users will hate us.) Luckily, we thought, Outlook 2010 provides the DisableCrossAccountCopy registry value/policy (cf. http://technet.microsoft.com/en-us/library/ff800883.aspx). (Because you can't do multiple Exchange organizations in a single profile before Outlook 2010, this only matters on Outlook 2010. Yes, I'm ignoring for the sake of this question copy/move to/from the filesystem.) In our test lab, in a test forest with a test Exchange organization, with a second Exchange account added to the profile in either of the "real" Exchange organizations, with the value set to "*", everything works as expected. On a workstation in one of the production domains, however, the setting does not seem to work. We have tried it under HKCU, HKLM, HKCU\Software\Policies, and HKLM\Software\Policies. It simply seems to be ignored. The value was set in the OCT on a test machine, but the OCT (and the ADM/ADMX file) have the wrong type for the value. We have located the value in the registry and removed it everywhere it is found, we think, and put it back in HKCU, but it still isn't taking. At the moment, a clean Outlook install is not an option - even if it was, we at this point would need to know what to do to fix the pushed copy (I didn't push the copy out to thousands of machines, I've just been asked to help clean up the current mess). Thoughts?

  Read the article

< Previous Page | 476 477 478 479 480 481 482 483 484 485 486 487  | Next Page >