Search Results

Search found 19747 results on 790 pages for 'internet cafe'.

Page 481/790 | < Previous Page | 477 478 479 480 481 482 483 484 485 486 487 488  | Next Page >

• Debian, 2 NICs load-balancing or agregating with one same gateway

  - by pouney

  Hi, I have one server, with double NICs connected to one switch with the same gateway. Behind the switch we have internet. |Debian| - eth0 - switch - internet - eth1 - same I don't understand how to load-balancing between eth0 and eth1. The inbound/outbound traffic always use eth1. This is the config: # The primary network interface allow-hotplug eth0 auto eth0 iface eth0 inet static address 192.168.248.82 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 allow-hotplug eth1 auto eth1 iface eth1 inet static address 192.168.248.83 netmask 255.255.255.240 network 192.168.248.80 broadcast 192.168.248.95 gateway 192.168.248.81 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.248.80 0.0.0.0 255.255.255.240 U 0 0 0 eth0 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.248.81 0.0.0.0 UG 0 0 0 eth0 Ips aren't real, it's just for the example. Anybody have an idea on correct routing to use eth0 on 192.168.248.82 and eth1 on 192.168.248.83 ? I have many example for multiple gateway but here it's the same. Thanks all. Regards

  Read the article

• Router startup problem

  - by gfmoz

  I have problems with my Tilgin Vood Router. As I try to start my router by turning the power on (captain obvious), it generally doesn't work the first 3-4 times. This is getting very annoying. Five minutes after turning the power on the router's signal LEDs don't blink in the way they should do in a connected state. I can connect to my routers web configuration interface through my PC connected to it via LAN though I can't access the internet. It usually takes the router five minutes to get to the point where it should be connected to the internet but as it doesn't work the first times. So I turn on my router 3-5 times, let him work 5 minutes and then suddenly, after turning the pow*emphasized text*er off and on again it all works. The problem is regarding startup only, when I get it to work everything runs as smooth as a 1980-s text-based C++ game on a 3ghz machine. I also have to restart my PC too in order for everything to work. - How can I solve this problem? - Just leave the router turned on all time? I prefer a daily IP switch, though. - May the problem have something to do with my PC? There is another one connected to the router too and it doesn't work there either.

  Read the article

• How to share text, pictures and video to restricted set of users

  - by joaoc

  I want to share pictures and videos of my kid growing up but I don't want it to be open to the public. I just want me and my wife to be able to add material and then share with grandparents and friends who would be given a username/password or some other solution that authenticates them. This content would preferably be available remotely over the internet or downloaded periodically to the allowed viewers computers. The second option most likely means they would have to install a client, which I am not too fond of doing (I would have to ask them to install it, help configure for different platforms, ...) I'm at the start but I would like software that also allows export of the data (if one day I want to migrate to a different solution). Folder sharing I don't know if Windows folder sharing is reliable, robust and safe enough to share over the internet. Dropbox could be a software solution, but it's limited to 2GB and requires receivers to also install and configure software. A folder is just a collection of files, so it would be harder to keep them organized with text describing the pictures/video Email I could email the content every now and then but videos are almost always too big to go as attachments This would also not provide a history of updates to anyone just recently joining in Are there other solutions to achieve this? NOTE: I also thought that software to run a local or remote blog could be an option but we aren't allowed to ask those questions on superuser because one admin doesn't like cloud-computing questions. But if you do think it's the best approach and can suggest a solution, do state it in the answers anyway!

  Read the article

• VLAN for WiFi traffic separation (new to VLANing)

  - by Philip

  I run a school network with switches in different departments. All is routed through to a central switch to access the servers. I would like to install WiFi access points in the different departments and have this routed through the firewall (an Untangle box that can captive-portal the traffic, to provide authentication) before it gets onto the LAN or to the Internet. I know that the ports that the APs connect to on the relevant switches need to be set to a different VLAN. My question is how do I configure these ports. Which are tagged? Which are untagged? I obviously don't want to interrupt normal network traffic. Am I correct in saying: The majority of the ports should be UNTAGGED VLAN 1? Those that have WiFi APs attached should be UNTAGGED VLAN 2 (only) The uplinks to the central switch should be TAGGED VLAN 1 and TAGGED VLAN 2 The central switch's incoming ports from the outlying switches should also be TAGGED VLAN 1 and TAGGED VLAN 2 There will be two links to the firewall (each on its own NIC), one UNTAGGED VLAN 1 (for normal internet access traffic) and one UNTAGGED VLAN 2 (for captive portal authentication). This does mean that all wireless traffic will be routed over a single NIC which will also up the workload for the firewall. At this stage, I'm not concerned about that load.

  Read the article

• How to connect 2 routers (Asmax and D-link)

  - by piobyz

  I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

  Read the article

• MacBook Air Keeps dropping Wi-Fi

  - by Robert Patrick

  So my MacBook Air keeps dropping Wi-Fi for some reason. It happens ONLY on my home network, and ONLY to my computer. I'm using a Linksys WRT54G router. I'm the only Mac on the network. Every other Wi-Fi network is perfectly fine, and every other computer on this network is fine. Many things can happen. It could say it's connected, but not be able to access the internet (whether it tells me that there's no internet access or not). It may just drop Wi-Fi altogether, and refuse to connect. Generally, if I unplug the router and plug it back in, it's all good. It also works if I restart my computer. This happens multiple times a day. Yesterday I did everything I know to get it to connect (restart router many times, restart my MacBook), and nothing worked. Eventually it just magically worked. How can I stop this from happening? We got a notice from Comcast a while ago saying that a bot called DNS Changer was detected on one or more machines on the network. I'm assuming that this can't be me, right?

  Read the article

• Route specific network traffic through vpn in virtualbox guest

  - by Sander

  I am running OSX with a windows server 2008 guest in Virtualbox. My goal is to route some of the network traffic in the host through the server guest. This is because the win2008 server has a VPN connection to my workplace using a Smartcard solution which can not operate on OSX. My current set-up is like this: OSX (Host): connected to the internet via en01 Win2008 (Guest): connected to the internet using NAT (lan1 in guest) has a SSTP VPN connection to my workplace is connected to the guest using an Host Only Adapter vboxnet0 (LAN2 in guest) The important part is about the host (OSX). Primarily I want all network traffic to just go through en01. However, all traffic which can only be accessed through the VPN must go through the guest and through the VPN. I have one specific FQDN which can only be accessed through the VPN (say corp.mycompany.com). I do not know much about networking. I thought I would be able to get it to work by bridging together LAN2 and LAN1 but this didn't seem to work this: http://archives.aidanfindlater.com/blog/2010/02/03/use-vpn-for-specific-sites-on-mac-os-x/ using a loopback adapter on WinXP (when I did not have win2008 yet, but this doesn't work because I can't create a PPTP connection) And I've also read about Routing and Remote Access but I have no idea on how to use this. Can someone help me in the right direction?

  Read the article

• [tcpdump] Proxy delegate refusing connexion ?

  - by simtris

  Hi guys, I'm a little disapointed ! My aim was to build a VERY simple smtp proxy under debian to handle mail from a port (51234) and forward it to the standard 25 port. I compile and install a "delegate" witch can handle easily that. It's working very well like that : delegated SERVER="smtp://anotherSmtpServer:25" -P51234 The strange thing is, it's working on my virtual test machine and on the dedicated server in local but I can't manage to use it trought internet. I test it like that. telnet [mySrv] 51234 Of course, no firewal, no deny host, no ined/xined, the service delegated is listening on the right port ... 2 clues : The port is answering trought internet with nmap as "51234/tcp open tcpwrapped" have a look at the tcpdump following : 22:50:54.864398 IP [myIp].1699 [mySrv].51234: S 2486749330:2486749330(0) win 65535 22:50:54.864449 IP [mySrv].51234 [myIp].1699: S 2486963525:2486963525(0) ack 2486749331 win 5840 22:50:54.948169 IP [myIp].1699 [mySrv].51234: . ack 1 win 64240 22:50:54.965134 IP [mySrv].43554 [myIp].auth: S 2485396968:2485396968(0) win 5840 22:50:55.243128 IP [myIp] [mySrv]: ICMP [myIp] tcp port auth unreachable, length 68 22:50:55.249646 IP [mySrv].51234 [myIp].1699: F 1:1(0) ack 1 win 46 22:50:55.309853 IP [myIp].1699 [mySrv].51234: . ack 2 win 64240 22:50:55.310126 IP [myIp].1699 [mySrv].51234: F 1:1(0) ack 2 win 64240 22:50:55.310137 IP [mySrv].51234 [myIp].1699: . ack 2 win 46 The part "auth" seems suspect to me but didn't ring a bell. I could certaily do with some help. Thx a lot !

  Read the article

• Manual NAT on Checkpoint (Redirect all http requests to a local web server)

  - by B. Kulakli

  We have a proxy server in our internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that says "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Tries to open www.google.com Should see web server output on local network Tries another web site on internet Should see web server output on local network Sets up proxy Tries to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), no replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my NAT rule at checkpoint NGX R60 does not include return packets. I definitely need some help.

  Read the article

• Sql Server 2005 Connection Unstable When Sharing Connection

  - by intermension

  When connecting to a customers hosting service via Sql Server Management Studio on an internet connection that also has other activity on it, the Sql Server connection to the hosting service is often dropped. An obvious work around to this problem is to NOT have additional traffic on the connection but it still begs the question "Why the Sql Server connection is so unstable?". If there is, for arguments sake, 100kb of bandwidth and a couple of downloads running that are being serviced at 35kB each then there is 30kB bandwidth spare capacity. If a 3rd download is started, that can be serviced at 35kB by the server, it will top out at 30kB and leave zero spare capacity. This is fine and all downloads get along nicely. However it seems that with Sql Server connections it doesn't matter if there is spare bandwidth. Sql Server regularly times out if there is any additional activity on the connection even if i have 1024kB spare bandwidth capacity. This has been experienced across different customer hosting providers over the years and so the assumption is that it's Sql Server related. Why does Sql Server (apparently) require exclusive access to the internet connection in order to maintain a connection... even if that connection has plenty of spare capacity over and above any additional activity on the connection?

  Read the article

• XenServer VMs can't reach network

  - by toto

  I'm currently trying to setup a small cloud architecture , I'm using in the installation CloudStack 2.2.14 which need two node : a management server (as node1) to provision the cloud and a hyperviser XenServer 5.6 SP2 to host the VMs (as node2). I succeded to create both node1 and node2 into an ESXi 5 VMWare as VMs. So The ESXi 5 is hosting two VMs node1 + node2 , and node2 which is the XenServer will host also VMs (such as ubuntu or Centos). Both node1 and node2 can ping each other and can get the internet connection from Esxi5 ,but My problem is : that VMs into the node2(XenServer) can't reach the network (can't ping node1 or Esxi or get an internet connection but they can ping VMs IN the node2(XenServer). So I tried to: 1-Setup a DHCP server as node3 in ESXi5 and connect node2(Xenserver) to him , but always the VMs into to node2 can't reach the outer network. 2-Setup a DCHP server into node2 , but always the same problem. So , 1-is there any other configuration i'm missing in node2 (considering that I'm sure about DNS , GW , NETMASK configuration)?. 2-Is it the problem because i'm Creating VMs into node2(XenSever) which is a VM into ESXi 5 ?

  Read the article

• Encrypted WiFi with no password?

  - by Ian Boyd

  Is there any standard that allows a WiFi connection to be encrypted, but not require a password? i know that (old, weak) WEP, and newer WPA/WPA2 require a password (i.e. shared secret). Meanwhile my own wireless connections are "open", and therefore unencrypted. There is no technical reason why i can't have an encrypted link that doesn't require the user to enter any password. Such technology exists today (see public key encryption and HTTPS). But does such a standard exist for WiFi? Note: i only want to protect communications, not limit internet access. i get the sense that no such standard exists (since i'm pretty capable with Google), but i'd like it confirmed. Claraification: i want to protect communcations, not limit internet access. That means users are not required to have a password (or its moral equivalent). This means users are not required: to know a password to know a passphrase to enter a CAPTCHA to draw a secret to have a key fob to know a PIN to use a pre-shared key have a pre-shared file to possess a certificate In other words: it has the same accessibility as before, but is now encrypted.

  Read the article

• Slackware - Assigning routes (IP address ranges) to one of many network adapters

  - by Dogbert

  I am using a Slackware 13.37 virtual machine within VirtualBox (current). I currently have a number of Ubuntu VMs on a single server, along with this Slackware VM. All VMs have been set up to use "Internal Network" mode, so they are all on a private LAN, and can see each other (ie: share files amongst themselves), but they remain private from the outside world. On on the these VMs (the Slackware one), I need to be able to grant it access to both this private network, and the internet at large. The first suggestion I found for handling this is to add another virtual network adapter to the VM, then set it to NAT. This results in the Slackware VM having the following network adapter setup: -NIC#1: Internal Network -NIC#2: NAT I want to set up the first network adapter (NIC#1) to handle all traffic on the following subnets: 10.10.0.0/255.255.0.0 192.168.1.0/255.255.255.0 And I want the second virtual network adapter (NIC#2) to handle everything else (ie: internet access). May I please have some assistance in setting this up on my Slackware VM? Additionally, I have searched for similar questions on SuperUser and Stackoverflow, but they all seem to pertain to my situation (ie: they all refer to OSX, or Ubuntu via the use of some UI-based tool). I'm trying to do this on Slack specifically via the command-line. Thanks!

  Read the article

• 802.11g -> wired ethernet bridging not working

  - by Malachi

  Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

  Read the article

• best practices for setting up a new windows 2008 R2 server with ec2 AWS

  - by Alex

  Can someone comment what they would add to the following list of SOP in terms of best practices? This is being set up on AWS, and then after further testing, back in our datacenter. Standard Operation Procedure (SOP): Installation Part: 2 - Installation of Software Components in Windows 2008 R2 (Updated). Step: 1 Logon to the host through Remote Desktop. Strp: 2 Open Server Manager - Server Roles - Install Web Server IIS 7.5 with compatible of IIS 6 features and Management compatibility mode. Step: 3 Open IE/Mozilla to Download the below listed software's and save all installation files to folder called "AWS Server Install Files" for future reference.. Net Framework 2.0 (Download that from internet) Crystal reports for .Net Framework 2.0 (x64) (Download that from internet) SQL Server 2005 (AWS Image) Step: 4 Once all software's saved on local drive, then Install it one by one. Step: 5 Navigate to Desktop folder to install the below listed softwares. Microsoft Asp.net 2.0 AjaxExtention 1.0 (placed on Desktop \Softwares) WebEx recorder. (placed on Desktop \Softwares) Winrar(placed on Desktop \Softwares) Step: 6 Make sure all the software are working fine. Step: 7 Inspect the server once entirely. Step: 8 Logoff & Stop the Instance.

  Read the article

• No LAN and SMB access, and Explorer not responsive, when using a second connection

  - by Lorenzo

  I apologize if this is a duplicate question, I know that there are several questions about multiple connection (LAN + LAN and LAN + dialup) but I haven't been able to find one that fits my scenario. I'm still using Windows XP on my corporate laptop, and I'm connected to the corporate LAN via Ethernet. The LAN NIC has a public IP address, although not accessible externally, obtained via the corporate DNS server. This connection is firewalled and requires a proxy to access Internet. To access Internet sites blocked by the corporate firewall, I use my smartphone via USB tethering. It is seen as a new LAN interface, and I get a private IP address (class 192.168..). There are two problems: The LAN is not accessible, as the default gateway goes to the tethering NIC. I'd like to solve this, but I can live with it. My PC becomes unresponsive if I use Windows Explorer to view local files, or even when I open the start menu. I guess that this is caused by attemps to connect to a mapped network drive. But I disabled the "Client for Microsoft Networks" in the tethering NIC. Why the system still hangs? Of course if I disable the Ethernet NIC, Explorer stops hanging. If you need further details, add a comment. Thanks!

  Read the article

• Clustered MSDTC

  - by niel

  Hi I'm setting up a SQL cluster (SQL 2008), Windows 2008 R2. I enable the network access on local dtc and then create a DTC resource in my cluster . the problem is that when i start up the resource it does nto pull through my settings to enable network access. the log shows this: MSDTC started with the following settings: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 0, Trasaction Manager Communication: Allow Inbound Transactions = 0, Allow Outbound Transactions = 0, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 0, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = Mutual Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 where when i restart the local dtc service it says this: Security Configuration (OFF = 0 and ON = 1): Allow Remote Administrator = 0, Network Clients = 1, Trasaction Manager Communication: Allow Inbound Transactions = 1, Allow Outbound Transactions = 1, Transaction Internet Protocol (TIP) = 0, Enable XA Transactions = 1, Enable SNA LU 6.2 Transactions = 1, MSDTC Communications Security = No Authentication Required, Account = NT AUTHORITY\NetworkService, Firewall Exclusion Detected = 0 Transaction Bridge Installed = 0 Filtering Duplicate Events = 1 settings on both nodes in teh cluster is the same. I have reinstalled and restarted to many times to mention. Any ideas ?

  Read the article

• Strange RDP / Remote Desktop problem

  - by John Landheer

  I'll try to be as specific as I can be: Server is running SBS 2008 R2 (with all updates) Server is connected to the internet Server has 2 NIC's, one is disabled Server is running RDP Service (accessible directly from the internet, I know, not as secure as it should be) Computers A and B are on the same local net. Computers A and B are both Windows 7. Users X and Y are both admins on the server Computer A can connect as user X to the server with mstsc Computer A can connect as user Y to the server with mstsc Computer B can connect as user X to the server with mstsc Computer B CANNOT connect as user Y to the server with mstsc! Error that username/password is incorrect. The last point is the problem, I get an authentication error. This used to work flawlessly for the last year. The server and desktops have been rebooted. EDIT: I tried: prefixing domain to the username prefixing the server computer name to the username change the password copy/paste the password from notepad to make sure it was correct I find it very strange.... EDIT: The computers are not on the same subnet as the server. The server is at my hosting provider. All computers as all users can reach the web app that is running on the server.

  Read the article

• Manual NAT on Checkpoint (Redirect all http requests to a local web server)

  - by kulakli

  Hi, We have a proxy server in internal network and I want to redirect all internet http requests to a web server in local network. It'll be like a Network Billboard that say "No direct connection is available. Set up your proxy etc." For example: A user starts the computer Opens the browser Trys to open www.google.com Should see web server output on local network Trys another web site on internet Should see web server output on local network Sets up proxy Trys to connect to a web site Web site should be loaded I have added a simple manual NAT rule to address translation in Checkpoint firewall but it simply does not work. Here is my address translation rule Source Destination Service T.Source T.Destination T.Service MY_PC A_GOOGLE_IP ALL ORIGINAL INT_WEB_SRV ORIGINAL Then when I ping A_GOOGLE_IP, replies come from INT_WEB_SRV, as I expected. However, when I try to connect A_GOOGLE_IP from browser (http://A_GOOGLE_IP), No replies come from SYN_SENT and falls into timeout. When I look at the firewall log of INT_WEB_SRV, I can see the incoming connection requests from MY_PC is accepted and NO denies. By the way, there is no problem to see INT_WEB_SRV (http://INT_WEB_SRV) from browser. My understanding is, my nat rule at checkpoint NGX R60 does not include return packets. I definitely need some help. Regards, Burak

  Read the article

• All application passwords lost on Windows 7

  - by Rynardt

  A couple of days ago I changed my Windows 7 login password. My laptop is on my company's domain, so password changes are done over the internal network. Since changing the password I noticed that all my saved Chrome passwords are missing. Also Skype, Windows Live, Internet Explorer and Outlook lost their saved passwords. I guess there could be more applications with lost passwords, but I have not opened them yet. This makes me think that most applications saves their passwords to a general password vault on the Windows system and this vault got somehow corrupted when I changed my domain login password for windows. Do anyone have any idea of how to fix this and prevent it from happening again? EDIT : More Info I do development work at the office, so most of the time I bypass the firewall and connect directly to the internet gateway. Now and then I would connect to the company wifi network to do printing and access files on a NAS. So by default my laptop does not connect to the wifi hotspot. On this occasion to update the password, I had to connect to the wifi. So referring to the comment by OmnipotentEntity below, could this have happened when the system rebooted without a connection to the network as the laptop does not auto connect to the wifi hotspot?

  Read the article

• Juniper router dropping pings to external interface

  - by Alexander Garden

  My organization has a Juniper SSG20-WLAN that routes our traffic to the outside world. We've been having intermittent problems with our internet connection so I wrote up a Python script to ping the internal interface of the router, the external interface, a couple of our internal servers, the ISP router our router talks to, their upstream provider, and Google and Yahoo for good measure. It does that about every minute. What I have found is that when our internet goes out, our Juniper router ceases responding to pings on the external interface. Everything past that is, of course, unreachable. The internal interface and our internal servers continue to echo back without interruption. None of the counters indicate dropped packets of any type. They all look normal. The logs complain about VIP servers being unavailable but otherwise nothing indicative of network issues. My questions are these: Does this exonerate our ISP? Or, contrawise, might a problem with the connection be causing the external interface to go down? Is there somewhere else in the SSG20, beside the system log and counters, that might help me track down info on the problem? UPDATE: Turned out that one of the switches between my monitoring box and the router was a router itself, and occasionally diverting from the gateway to itself. Kudos to those who made suggestions along those lines. Not really sure which answer to mark as accepted, as it was really stuff in the comments that turned out to be right. Thanks for the suggestions.

  Read the article

• XP box with 3 NICs on Server 2003 Domain

  - by Hannibal

  I have assigned all three NICs IP addresses that are outside the DHCP pool. I have 2 NICs are connected to 1 switch and the 3rd to my second switch. I want to assign one of the two NICs on the 1st switch to "normal" network activity (e.g. internet access, RDP, etc.) The other two NICs I want to reserve for mirroring ports on their respective switches. While this machine is connected to the domain I can access the internet and Remote Desktop. I have no idea which NIC I am using until I start mirroring a port, at which time, if I happen to be connected through one of the NICs I have dedicated to mirroring, I lose my remote desktop. I am aware that I would have more control over the NICs using Linux. I want to explore Windows solutions before I go that route because reinstalling another OS would be inconvenient (but not impossible). I would likely use a version of Backtrack (3 or 4 not sure). I would also have to learn how to access the machine remotely but I've done it before so this would be a minor obstacle. Thank you for your assistance.

  Read the article

• secure user-authentication in squid

  - by Isaac

  once upon a time, there was a beautiful warm virtual-jungle in south america, and a squid server lived there. here is an perceptual image of the network: <the Internet> | | A | B Users <---------> [squid-Server] <---> [LDAP-Server] When the Users request access to the Internet, squid ask their name and passport, authenticate them by LDAP and if ldap approved them, then he granted them. Everyone was happy until some sniffers stole passport in path between users and squid [path A]. This disaster happened because squid used Basic-Authentication method. The people of jungle gathered to solve the problem. Some bunnies offered using NTLM of method. Snakes prefered Digest-Authentication while Kerberos recommended by trees. After all, many solution offered by people of jungle and all was confused! The Lion decided to end the situation. He shouted the rules for solutions: Shall the solution be secure! Shall the solution work for most of browsers and softwares (e.g. download softwares) Shall the solution be simple and do not need other huge subsystem (like Samba server) Shall not the method depend on special domain. (e.g. Active Directory) Then, a very resonable-comprehensive-clever solution offered by a monkey, making him the new king of the jungle! can you guess what was the solution? Tip: The path between squid and LDAP is protected by the lion, so the solution have not to secure it. Note: sorry for this boring and messy story! /~\/~\/~\ /\~/~\/~\/~\/~\ ((/~\/~\/~\/~\/~\)) (/~\/~\/~\/~\/~\/~\/~\) (//// ~ ~ \\\\) (\\\\( (0) (0) )////) (\\\\( __\-/__ )////) (\\\( /-\ )///) (\\\( (""""") )///) (\\\( \^^^/ )///) (\\\( )///) (\/~\/~\/~\/) ** (\/~\/~\/) *####* | | **** /| | | |\ \\ _/ | | | | \_ _________// Thanks! (,,)(,,)_(,,)(,,)--------'

  Read the article

• The Story of secure user-authentication in squid

  - by Isaac

  once upon a time, there was a beautiful warm virtual-jungle in south america, and a squid server lived there. here is an perceptual image of the network: <the Internet> | | A | B Users <---------> [squid-Server] <---> [LDAP-Server] When the Users request access to the Internet, squid ask their name and passport, authenticate them by LDAP and if ldap approved them, then he granted them. Everyone was happy until some sniffers stole passport in path between users and squid [path A]. This disaster happened because squid used Basic-Authentication method. The people of jungle gathered to solve the problem. Some bunnies offered using NTLM of method. Snakes prefered Digest-Authentication while Kerberos recommended by trees. After all, many solution offered by people of jungle and all was confused! The Lion decided to end the situation. He shouted the rules for solutions: Shall the solution be secure! Shall the solution work for most of browsers and softwares (e.g. download softwares) Shall the solution be simple and do not need other huge subsystem (like Samba server) Shall not the method depend on special domain. (e.g. Active Directory) Then, a very resonable-comprehensive-clever solution offered by a monkey, making him the new king of the jungle! can you guess what was the solution? Tip: The path between squid and LDAP is protected by the lion, so the solution have not to secure it. Note: sorry if the story is boring and messy, but most of it is real! =) /~\/~\/~\ /\~/~\/~\/~\/~\ ((/~\/~\/~\/~\/~\)) (/~\/~\/~\/~\/~\/~\/~\) (//// ~ ~ \\\\) (\\\\( (0) (0) )////) (\\\\( __\-/__ )////) (\\\( /-\ )///) (\\\( (""""") )///) (\\\( \^^^/ )///) (\\\( )///) (\/~\/~\/~\/) ** (\/~\/~\/) *####* | | **** /| | | |\ \\ _/ | | | | \_ _________// Thanks! (,,)(,,)_(,,)(,,)--------'

  Read the article

• Iptables rules, forward between two interfaces

  - by Marco

  i have a some difficulties in configuring my ubuntu server firewall ... my situation is this: eth0 - internet eth1 - lan1 eth2 - lan2 I want that clients from lan1 can't communicate with clients from lan2, except for some specific services. E.g. i want that clients in lan1 can ssh into client in lan2, but only that. Any other comunication is forbidden. So, i add this rules to iptables: #Block all traffic between lan, but permit traffic to internet iptables -I FORWARD -i eth1 -o ! eth0 -j DROP iptables -I FORWARD -i eth2 -o ! eth0 -j DROP # Accept ssh traffic from lan1 to client 192.168.20.2 in lan2 iptables -A FORWARD -i eth1 -o eth2 -p tcp --dport 22 -d 192.168.20.2 -j ACCEPT This didn't works. Doing iptables -L FORWARD -v i see: Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 33 144 DROP all -- eth1 !eth0 anywhere anywhere 0 0 DROP all -- eth2 !eth0 anywhere anywhere 23630 20M ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1 any anywhere anywhere 175 9957 ACCEPT all -- eth1 any anywhere anywhere 107 6420 ACCEPT all -- eth2 any anywhere anywhere 0 0 ACCEPT all -- pptp+ any anywhere anywhere 0 0 ACCEPT all -- tun+ any anywhere anywhere 0 0 ACCEPT tcp -- eth1 eth2 anywhere server2.lan tcp dpt:ssh All packets are dropped, and the count of packets for the last rule is 0 ... How i have to modify my configuration? Thank you. Regards Marco

  Read the article

< Previous Page | 477 478 479 480 481 482 483 484 485 486 487 488  | Next Page >