Search Results

Search found 14961 results on 599 pages for 'mac clients'.

Page 483/599 | < Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >

• OpenVPN: ifup tap0 drops all connections

  - by raspi

  I'm trying to create star shaped "virtual" LAN with OpenVPN which is not connected to physical network. ie. tap0 packets should not go to eth0. Packet should only go through OpenVPN to connected clients. This setup works with my OpenVPN testing machine which runs Virtual Box but not on my actual server which is running on top of Xen. Both servers are running Ubuntu Intrepid. /etc/network/interfaces: iface tap0 inet manual address 10.10.10.1 netmask 255.255.255.0 gateway 10.10.10.1 /etc/openvpn/server.conf mode server tls-server port 1194 proto udp dev tap client-to-client ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/servername.crt key /etc/openvpn/easy-rsa/keys/servername.key dh /etc/openvpn/easy-rsa/keys/dh384.pem ifconfig-pool-persist ipp.txt server-bridge 10.10.10.1 255.255.255.0 10.10.10.128 10.10.10.250 push .route 10.10.10.1 255.255.255.0 keepalive 5 60 comp-lzo persist-key persist-tun status /var/log/openvpn-status.log log-append /var/log/openvpn.log verb 3 user nobody group nogroup ifup tap0 on Virtual Box: everything ok, SSH keeps running. But on Xen SSH connection drops and I have to reboot whole machine. What I'm missing?

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• Accounting setup in freeradius with mikrotik and the "always" module

  - by Matt

  I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

  Read the article

• nginx connection pool race condition?

  - by wlf

  I have a shared hosting server with high traffic. I have a lightweight apache mod_proxy for static content that from time to time has a "504 proxy error" problem proxing to apache/mod_php. Error log says: error reading status line from remote server 127.0.0.1:8080 Error reading from remote server returned by / This is what the apache documentation says about it. proxy-initial-not-pooled If this variable is set no pooled connection will be reused if the client connection is an initial connection. This avoids the "proxy: error reading status line from remote server" error message caused by the race condition that the backend server closed the pooled connection after the connection check by the proxy and before data sent by the proxy reached the backend. It has to be kept in mind that setting this variable downgrades performance, especially with HTTP/1.0 clients. I am really concerned about this downgrade in performance therefore I started to look at nginx immediately. I am new to nginx and time is crucial right now, I can't afford to waste days to study it just to find out there is the same race condition issue. Is nginx affected by this connection pool race condition? Thanks

  Read the article

• Citrix Metaframe/RD - screen refresh weirdness

  - by southof40

  I access a clients W2003 machine (XEN Virtualization) using RD over Citrix Metaframe. Everything used to be fine. Some weeks ago things turned bad ! All is well initially but after, say, 5 minutes the screen will stop refreshing. Rather weirdly you can then still proceed in a way as you can make the screen refresh by getting the RD window to go through a restore/maximise cycle (this is only possible using the ALT-BREAK shortcut as everything else is locked up). This then allows you to proceed by typing something and going ALT-BREAK to see the results. Using menus is just not possible at all. There's some indications that clearing the java cache between sessions helps. Also that the lockup happens more quickly if you make the 'lots of stuff happen' on the screen - for instance if you do a directory listing of a big directory then often that will cause the lockup to occur. Similary opening a dense Excel workbook and then scrolling it will cause the lockup to occur. Any Metaframe veterans out there who recognise these symptoms ? I'd be very grateful as it's driving me nuts.

  Read the article

• OpenVPN connected but not internet access on the client

  - by Stefan

  I've setup OpenVPN following this tutorial, and everything works fine except that I don't have an internet connection on the client while connected to VPN. http://www.howtoforge.com/internet-and-lan-over-vpn-using-openvpn-linux-server-windows-linux-clients-works-for-gaming-and-through-firewalls My VPS server config is as follows (Ubuntu): dev tun proto udp port 1194 ca /etc/openvpn/easy-rsa/keys/ca.crt cert /etc/openvpn/easy-rsa/keys/server.crt key /etc/openvpn/easy-rsa/keys/server.key dh /etc/openvpn/easy-rsa/keys/dh1024.pem user nobody group nogroup server 10.8.0.0 255.255.255.0 persist-key persist-tun status /var/log/openvpn-status.log verb 3 client-to-client push "redirect-gateway local def1" #set the dns servers push "dhcp-option DNS 8.8.8.8" push "dhcp-option DNS 8.8.4.4" log-append /var/log/openvpn comp-lzo plugin /usr/lib/openvpn/openvpn-auth-pam.so common-auth My client config is as follows (Windows 7): dev tun client proto udp remote XXX.XXX.XXX.XXX 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert stefan.crt key stefan.key comp-lzo verb 3 auth-user-pass redirect-gateway local def1 I've turned off the firewall on the server for testing purposes (it doesn't help), and tried both wired and wireless connecting on the client. I've tried many Google results... but nothing seems to help. Can you help me? Thanks so far...

  Read the article

• Postfix relay gives error 450 while it should be 550

  - by dieter-be

  Hi, we use postfix to do relaying. We get several messages like the following in /var/log/mail (slightly edited) Apr 13 13:30:29 linserver postfix/smtpd[1064]: NOQUEUE: reject: RCPT from unknown[$ip]: 450 4.1.1 <[email protected]>: Recipient address rejected: undeliverable address: host domain.be [$ip] said: 550 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table (in reply to RCPT TO command); from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<BLUESTREAK.domain.local> Now, when the master mail servers gives a 550, claiming that the user does not exist, I want the relay to also give a 550 back. What happens now is that it seems to return a 450, causing clients to keep messages queued, keep trying and only notify users after a certain period has passed. According to what I could find, the soft_bounce could cause this. But we have not enabled this option (and by default it's off according to postfix docs) It might also have something to do with the *_reject_code postconf values. Especially since the log message complains the unknown ip. But as you can see in the postconf output below, smtpd_sender_restrictions and smtpd_client_restrictions are empty. So even if it would try to do any restrictions there, 550 is the "worst" error going on, so that's what I expect to be returned to the client. postconf: http://sprunge.us/JYgB Thanks, Dieter

  Read the article

• MySQL Server Is Slow

  - by user2853965746

  I have two MySQL servers and one was just recently setup. The one I just recently setup is a bit slower than my older one, which kind of bothers me because I don't want my clients to be upset with the speed difference when I launch the new one. The older server runs on Ubuntu (~13.04 I believe) and the new one is on Debian 6. Both servers are 2GB ram, but my newer server is has an SSD, so I thought it might be the same speed if not faster. Anyway, the speed difference isn't too much (both are still under a second, but still noticeable). Whenever I select 50 rows from the user table on my older server (SELECT * FROM users LIMIT 50), I get the results in 0.003 s. There is 100,000+ accounts in that table. Whenever running the same command on the same table with only six dev accounts, it takes 0.069 s. It may not seem like a lot, but it's noticeable when you're used to a fast response. I added skip-name-resolve to the config and it didn't seem to help. Basically I'm asking if anyone knows what can cause a MySQL server to be slow in Debian 6? Should I just drop it and switch to Ubuntu like the older server (I don't think the OS is the problem, but you never know)? The older server is under a lot of use too, it's used a lot for web api's on my website. A lot of connections and stuff, and it still remains fast.

  Read the article

• DNS something is wrong?

  - by Nickolas R.

  Hello I am configuring bind9 on a server with two network interfaces, one is connected to the LAN and the other is connected to the Internet through NAT so bind is not faced directly to the Internet. Everything seems to work fine, clients can do both forward and reverse lookups but somethings seems strange. On the server if i try to ping www.google.com one time, a great amount of network activity is genereated, alot more that one would expect so i decided to sniff the traffic with tcpdump. When loading the dump into Wireshark i can see about 250 entries with "Standard query A" and "Standard query response" Here a some of the entries from the dump DNS Standard query A www.google.com DNS Standard query A blackhole-1.iana.org DNS Standard query A blackhole-2.iana.org DNS Standard query response DNS Standard query A ns2.isc-sns.com DNS Standard query A ns1.isc-sns.net DNS Standard query A ns3.isc-sns.info DNS Standard query response PTR b.iana-servers.net RRSIG DNS Standard query A auth2.dns.cogentco.com DNS Standard query A ns1.crsnic.net DNS Standard query A ns2.nsiregistry.net DNS Standard query A ns3.verisign-grs.net DNS Standard query A ns4.verisign-grs.net DNS Standard query PTR 79.52.19.199.in-addr.arpa I do not have too much experince with DNS yet, but i am pretty sure that something is wrong. Anybody that have an idea of whats is going on?

  Read the article

• Talk on multiple IRC channels at once?

  - by TwoPixelGrid

  I seem to remember, back in '91 or so, that the console-based IRCII implemention on the Solaris box that first got me on the net would let me /Join multiple channels on a given network such that, as new channels were joined, they would start scrolling to the single console view. Let's call it the 'interleaved conversation' chat paradigm. Am I rembering this correctly? More importantly, is there a modern way of doing this in any of the GUI-based clients? I'm surprised this isn't a common desire/feature because I think it would greatly improve the experience, especially on channels with high SNR. For example, If I'm working on a project I may connect to Freenode and join : #Qt,#OpenGL,#C++. As it is now, with mIRC,Xchat, I have to manually flip between pages just to see whats being said and to reply. What I envision would go more like this (using only 2 channels for simplicity) /join #QT #OpenGL < [QT] QtChannelUser: Hello TwoPixelGrid. < [OpenGL] OpenGLChannelUser: Hi there TwoPixelGrid. @QT: Hi QtChannelUser @OpenGL: Hello againOpenGLChannelUser And this message is going out to all my channels. Do I have to write a new client or is this already out there?

  Read the article

• Sql Server 2005 database lost, How to recover all records. MDF/LDF size is same as it should be

  - by Shantanu Gupta

  Few months back, I installed a sql server 2005 on one of my client machine. I gave him a backup option to take backup timely but he never took any backup. Today he called me that "i m not able to see any record of mine." I visited at my clients system and saw that none of the record was present on the tables. There was not even a single row in any of the tables. Then I checked if he has any backup file which i found to be absent. I asked him the reason what could be the possible cause. He said it might be due to virus. After this I checked the size of mdf and ldf file and found it should be what it is. when i created his server mdf ldf file had 2MB of database now it is 83 MB and 193Mb mdf/ldf respectively. This shows the data is still present in it but it is not being displayed. What could be the possible cause and how can i restore all data back to my tables ?

  Read the article

• Total newb having SSH and remote MySQL access problems

  - by kscott

  I don't often work with linux or need to SSH into remote MySQL databases, so pardon my ignorance. For months I had been using the HeidiSQL client application to remotely access a MySQL database. Today two things happened: the DB moved to a new server and I updated HeidiSQL, now I cannot log in to the MySQL server, when attempting I get this message from Heidi: SQL Error (2003) in statement #0: Can't connect to MySQL server on 'localhost' (10061) If I use Putty, I can connect to the server and get MySQL access through command line, including fetching data from the DB. I assume this means my credentials and address are correct, but do not understand why putting those same details into HeidiSQL's SSH tunnel info won't work. I also downloaded the MySQL Workbench and attempted to set up a connection through that client and got this message: Cannot Connect to Database Server Your connection attempt failed for user 'myusername' from your host to server at localhost:3306: Lost connection to MySQL server at 'reading initial communication packet', system error: 0 Please: 1 Check that mysql is running on server localhost 2 Check that mysql is running on port 3306 (note: 3306 is the default, but this can be changed) 3 Check the myusername has rights to connect to localhost from your address (mysql rights define what clients can connect to the server and from which machines) 4 Make sure you are both providing a password if needed and using the correct password for localhost connecting from the host address you're connecting from From Googling around I see that it could be related to the MySQL bind-address, but I am a third party sub-contractor with no access to the MySQL settings of this box and the system admin is assuring me that I'm an idiot and need to figure it out on my end. This is completely possible but I don't know what else to try. Edit 1 - The client settings I am using In Heidi and MySQL Workbench I am using the following: SSH host + port: theHostnameOfTheRemoteServer.com:22 {this is the same host I can Putty to} SSH Username: mySSHusername {the same user name I use for my Putty connection} SSH Password: mySSHpassword {the same password for the Putty connection} Local port: 3307 MySQL host: theHostnameOfTheRemoteServer.com MySQL User: mySQLusername {which I can connect with once in with Putty} MySQL Password: mySQLpassword {which works once in with Putty} Port: 3306

  Read the article

• What is Best storage servers infrastructure ? DAS/NAS/SAN or installing GlusterFS/LUSTER/HDFS/RBDB

  - by TORr0t

  I am trying to design an infrastucture for the project I am working on. It would be somehow a file-sharing/downloading project (like rapidshare) and I would need high storage sizes and good scability, and I would add new storage nodes after my project grows up. I have come up with 3 solutions for my project which are using Luster, GlusterFS, HDFS, RDBD. For start, i would have 2 servers, one server is for glusterfs client + webserver + db server+ a streaming server, and the other server is gluster storage node. (After sometime, i would be adding more node servers, and client servers (dont know how many new client new servers to add, will see later) So, i am thinking to work with glusterfs. But i really wonder that if i have to use high performance servers with high sotrage sizes or avarage/slow servers with high storage sizes? Or nas/das/san solutions are better for glusterfs storage nodes? I might buy a nas and install glusterfs onto it. I would be happy to listen to your recommendations for the server properties (for each clients and nodes) . I really dont know if I really need high amount of ram and good cpus to for the nodes. I am sure i need it for client servers. The files would be streamed as well, so the Automatic file replication is important, thus, my system should work like a cloud, when needed, according to high traffic, the storage nodes should copy the most demanded file to be streamed and would help me to get rid of scability problems and my visitors would able to stream/download those files. Also, i am open to your experiences/thoughts about any good solution. Luster, hdfs, rbdb are the other options and i would be happy to listen to your thoughts here. I would be very very happy to hear back from anyone commented of any words I have used here. Thanks

  Read the article

• Can I have 2Gbit over 1Gbit Nics

  - by Daniel

  So this really baffles me. Apparently because 1Gbit can transmit data in both directions simultaneously it should be possible to get 2Gbit of data transfer on a single NIC (1Gbit flow seend and 1Gbit receive). People claim that because 1Gbit is full-duplex (almost always) it is exactly 2Gbit in total. My intuition and electrical background tells me that something is not right here 4 twisted pairs 250Mbit capacity each gives 1Gbit. Unless it is really possible to transfer data in both directions simultaneously. I did a test with iperf. Ubuntu server 12.04 <-- MacBook Pro. Both with decent CPU speed. Tested speed of connection individually and on Mac I can see 112MB/s regardless which direction data is going. On Ubuntu with vnstat and ifstat I got 970Mbit speeds. Now, launching iperf in server mode on both machines at the same time and sending data using 2 iperf clients shows that I'm for example on Ubuntu box sending at 600Mbit, and receiving 350Mbit. which adds up to pretty much 1Gbit link. So to me there is no magical 2Gbit. Can someone confirm that or tell why I'm wrong? Another thing that confuses me i the fact that e.g. 24-port switch has for example: Throughput»up»to:»50.6Mpps Switching»capacity:»68Gbps Switch»fabric»speed:»88Gbps Which would suggest thay can handle 2GBit per port.

  Read the article

• samba "username map" stopped to work

  - by Kris_R

  It was time to upgrade our group server (new HDs, problems with old installation of DRBD, etc..). Going as usually for CentOS i upgraded whole system from 6.3 to 6.4 The later one came with samba 3.6 as the old one was 3.5. I transferred most of users by copying /etc/password, /etc/shadow and samba accounts with pdbedit. Homes were on nfs-drive. The translation of unix accounts to samba accounts are located in /etc/samba/smbusers. Strangely enough on some windows clients there was problem to connect to samba-shares. In one case the only thing that worked was, instead of giving windows name, to use the unix account. In another one, it was possible to mount network drive and to open it in Windows Explorer, however other applications like "Total commander" at the attempt of opening this drive gave the message "Cannot connect to z:" (sometimes at this moment user/pass were requested). The smb.conf has following entries: [global] security = user passdb backend = tdbsam username map = /etc/samba/smbusers ... [Kris] comment = Kris's Private path = /SMB/Users/Kris writeable = yes read only = no browseable = yes users = krisr printable = no security mask = 0777 force security mode = 0 directory security mask = 0777 force directory security mode = 0 force create mode = 0775 force directory mode = 6775 The smbusers: # Unix_name = SMB_name1 SMB_name2 ... krisr = Kris Of course testparm runs without any errors. I was used from samba 3.5 to outputs of form Mapped user Kris to krisr. Nothing like this happens now. Just message check_sam_security: Couldn't find user Kris in passdb. I read on web that some guys had problem with 3.6 and security = ADS, but these were not helpful for me. I'm seriously thinking about downgrading back to samba 3.5 but before this step I wanted to ask if somebody knows the solution of these problems. p.s. i've asked this question at serverfault but no answer came. Maybe I have more luck with this forum. Sorry for duplicate if any of you reads both.

  Read the article

• Resources for Smartphone Security

  - by Shial

  My organization is currently working on improving our data and network security due to increasing HIPAA laws and a general need to get a better grasp on controlling our health related information. We are a non-profit working with people with developmental disabilities so we handle a lot of medical related information. One area that has been identified as a risk is our use of smartphones, specifically at this time Windows Mobile 6.1 devices from T-Mobile. We do not utilize the VPNs on the phones so there isn't any way they can access our databases or file servers (username/password for VPNs is not the domain logons). What would be exposed however is the particular user's email account since you could extract out the username/password and access the email either on the device or on our web email (Exchange 2003) which could contain HIPAA protected confidential information about clients and services and this would be an incident that would have to be reported. What resources or ideas would help us secure these devices? I'm not worried about data interception (using SSL) but more about physical theft or loss of the device. Are there websites that I just have not found with guidelines and suggestions or particualar products that would help protect us? I also don't want to limit the discussion to windows Mobile either. I myself am looking at an android 2.0 device and there is always the eventual possibility we could get pushed to enable the VPNs. I know this is a subject that likely won't have any particular correct answer and it is something we should all be aware of since there devices are sitting outside of our immediate control most of the time.

  Read the article

• tcp connect hangs on SYN_SENT if something listens, gets CONN_REFUSED if nothing listens

  - by Amos Shapira

  I'm hitting a very strange problem - when I try to connect to one of our servers the client hangs with SYN_SENT if something listens on the port (e.g. Apache on port 80, sshd on port 22 or SMTP on port 25) but if I try to connect to a port on which nothing listens then I immediately get a "CONNECTION refused" error. Connecting to other applications (e.g. rsyncd on some arbitrary port) succeeds. I ran tcpdump on the server and see that the SYN packets arrive to it but it only sends a response if nothing listens on that port. e.g.: on the server I run: # tcpdump -nn port 81 06:49:34.641080 IP 10.x.y.z.49829 server.81: S 3966400723:3966400723(0) win 12320 06:49:34.641118 IP server.81 x.y.z.49829: R 0:0(0) ack 3966400724 win 0 But if I listen on this port, e.g. with nc -4lvvv 81 & Then the output of tcpdump is: 06:44:31.063614 IP x.y.z.45954 server.81: S 3493682313:3493682313(0) win 12320 (and repeats until I stop it) The server is CentOS 5, the client is Ubuntu 11.04, the connection is done between two LAN's over per-user TCP OpenVPN. Connection to other servers on that network do not have a problem. Connecting from the other servers on the same network to that server works fine. Connections from other clients in our office over openvpn is also not a problem. What am I missing? Thanks.

  Read the article

• Need to Remove Exchange 2003 Server That Crashed During Transition to 2010

  - by ThaKidd

  As the title stated, we were running an Exchange 2003 server that we knew was going down soon so we purchased a second server and installed Exchange 2010 into the AD. We managed to move all of the mailboxes off of 2003 and also managed to get the Offline Address Book setup on 2010. At this point the 2003 server bit the dust and will no longer boot. Therefore we were unable to properly uninstall Exchange and remove the last 2003 server so it still exists in AD. As far as the clients are concerned, everything is working properly. However, when I run the Microsoft Exchange Profile Analyzer, I still see the old server and its Administrative Group. I am going to guess that since the old server is showing up in AD, I will not be able to raise Exchange or AD functionality (as the 2003 server was also the only AD DC) levels. I have forced the 2003 DC out of AD so that is no longer an issue. Old Setup: Windows 2003 Server Enterprise & Exchange 2003 Standard New Setup: Windows 2010 Server Enterprise & Exchange 2010 Standard Two Questions: How do you go about manually forcing the 2003 server and its administrative group out of AD? When that is finished, where do you raise the Exchange mode (can't find this for the life of me)?

  Read the article

• Remote Desktop Network Level Authentication Not Supported

  - by Iszi

  I'm running Windows XP Professional SP3 x86, trying to connect to a system with Windows 7 Ultimate SP1 x64. Recently, I updated the Remote Desktop Connection software on the XP system in hopes of using Network Level Authentication (NLA) for my connections to the Windows 7 box. After the update, I connected to the Windows 7 box over RDP and enabled NLA believing that the updated client should support it. After disconnecting and attempting to reconnect, I'm presented with the following error: The remote computer requires Network Level Authentication, which your computer does not support. For assistance, contact your system administrator or technical support. So, I checked the About page in Remote Desktop Connection to make sure the update had applied. This is what I see. Remote Desktop Connection Shell Version 6.1.7600 Control Version 6.1.7600 © 2007 Microsoft Corporation. All rights reserved. Network Level Authentication not supported. Remote Desktop Protocol 7.0 supported. I thought NLA was supposed to be a part of RDP 7.0 clients. Is there a component I'm missing somewhere?

  Read the article

• Avoiding DNS timeouts when a dns server fails

  - by Neil Katin

  We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

  Read the article

• How to run a WebPy server on port 8080 using DDNS of dlink router and to access this site from internet?

  - by nuke1010

  I have two major issue with setting up a web server using my dlink DIR-600L router. Issue 1: I run a WebPy server on port 8080. But the DDNS service providers (like dlinkddns.com or dyndns.org) only allows port 80. I can run the server in port 80 with sudo command. But my server become vulnerable if i give root access. So I tried port forwarding in the router and server. But no use. I don't know if I done that correctly. Issue 2: Even though the server runs on port 80, I can access my site from my local machines only using registered domain names ( say, nikz.dyndns.org). No one on internet cannot load this site even when its totally up. As I observed server log, the request from other clients never reached my server. I need to run this server on port 8080 and i need to access this site from internet. How can I do it? any idea?

  Read the article

• OpenVPN bad source address from client

  - by Bogdan

  I have one problem with OpenVPN. There are a lot drops records in the openvpn log file on the server: Mon Oct 22 10:14:41 2012 us=726541 laptop/???:1194 MULTI: bad source address from client [192.168.1.107], packet dropped grep -E "^[a-z]" server.conf ----- port 1194 proto udp dev tun ca data/ca.crt cert data/server.crt key data/server.key dh data/dh1024.pem tls-server tls-auth data/ta.key 0 remote-cert-tls client cipher AES-256-CBC tun-mtu 1200 server 10.10.10.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 8.8.8.8" client-to-client client-config-dir /etc/openvpn/ccd route 10.10.10.0 255.255.255.0 keepalive 10 120 comp-lzo persist-key persist-tun max-clients 5 status /var/log/status-openvpn.log log /var/log/openvpn.log verb 4 auth-user-pass-verify /etc/openvpn/verify.sh via-file tmp-dir /tmp script-security 2 ----- cat ccd/laptop ----- iroute 10.10.10.0 255.255.255.0 ----- cat client.conf ----- remote server ip 1194 client dev tun ping 10 comp-lzo proto udp tls-client tls-auth data/ta.key 1 pkcs12 data/vpn.laptop.p12 remote-cert-tls server #ns-cert-type server persist-key persist-tun cipher AES-256-CBC verb 3 pull auth-user-pass /home/user/.openvpn/users.db ----- According to "Jan Just Keijser - OpenVPN 2 Cookbook" root of the problem is incorrect config options.see the screenshot But, as you see, my config has such options. Could you please help me to solve this problem. @week Verb leverl=6; client log. Mon Oct 22 16:06:02 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Mon Oct 22 16:06:02 2012 /sbin/ifconfig tun0 10.10.10.3 pointopoint 10.10.10.5 mtu 1500 Mon Oct 22 16:06:02 2012 /sbin/route add -net xxxx netmask 255.255.255.255 gw 192.168.1.1 Mon Oct 22 16:06:02 2012 /sbin/route add -net 0.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 /sbin/route add -net 128.0.0.0 netmask 128.0.0.0 gw 10.10.10.5 Mon Oct 22 16:06:02 2012 Initialization Sequence Completed cat ccd/latop iroute 10.10.10.0 255.255.255.0 ifconfig-push 10.10.10.3 10.10.10.5

  Read the article

• Printing to a remote printer through the internet

  - by Lock

  I have a remote network (A) that is connected to a head office (B) through a private network. Network A only has 1 PC that requires the connection, and this is into a terminal server at network B. We want to save money by getting rid of the private network as only 1 PC now access it and it seems silly to pay ~$400 per month for something that is accessed by 1 PC. A VPN tunnel is out of the question as the provider wants to charge $600 a month for a VPN tunnel (more than a private network? I might get them to check these numbers). I was thinking of 2 options: 1) VPN client on the PC. This wouldn't cost a thing as we already have VPN users available. 2) Open up a port on the firewall of network B, forwarding to the terminal server. Now the problem is this: On the terminal server, the program that is accessed is for printing labels to the printer that is at network A. The program is setup to send all print jobs to a printer that is setup locally on the terminal server, which has its port mapped to the IP address of the printer that is at network A. If we got rid of the VPN tunnel and used clients/open up firewall port, the printer would no longer be able to find network A, and hence printing would not work. Any ideas to combat this issue? Can the printers at the remote network be setup as internet printers? I've never had any experience with internet printers. Can you open up ports and map to a public static IP address?

  Read the article

• Windows 7 libraries nightmare

  - by Lobuno

  In our active directory we deploy a policy to our clients where the personal directory (My documents) is redirected to a file server of ours \server\share\username\Documents In older systems everything worked fine. in Windows 7 some users are experimenting the following symptoms: The Documents library is EMPTY Where the documents library should be shown in Explorer an empty white icon is displayed. No caption. Right clicking in the Documents library to edit the folders that are part of the libraries brings the dialog up. However, that dialog is unusable. No folder is present there and clicking Add folder does nothing. Deleting the library and auto-creating it doesn't solve the problem The shared directory can be accessed via UNC paths and it can be mounted as a shared drive as well. The library is still broken. The shared drives are on a W2008 indexed server... Using the Windows Library tool utility doesn't solve the problem. What can the cause of this problem be and how can this be solved?

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

< Previous Page | 479 480 481 482 483 484 485 486 487 488 489 490  | Next Page >