Search Results

Search found 19478 results on 780 pages for 'delay load'.

Page 486/780 | < Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493  | Next Page >

  • Kernel panic when bringing up DRBD resource

    - by sc.
    I'm trying to set up two machines synchonizing with DRBD. The storage is setup as follows: PV - LVM - DRBD - CLVM - GFS2. DRBD is set up in dual primary mode. The first server is set up and running fine in primary mode. The drives on the first server have data on them. I've set up the second server and I'm trying to bring up the DRBD resources. I created all the base LVM's to match the first server. After initializing the resources with `` drbdadm create-md storage I'm bringing up the resources by issuing drbdadm up storage After issuing that command, I get a kernel panic and the server reboots in 30 seconds. Here's a screen capture. My configuration is as follows: OS: CentOS 6 uname -a Linux host.structuralcomponents.net 2.6.32-279.5.2.el6.x86_64 #1 SMP Fri Aug 24 01:07:11 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux rpm -qa | grep drbd kmod-drbd84-8.4.1-2.el6.elrepo.x86_64 drbd84-utils-8.4.1-2.el6.elrepo.x86_64 cat /etc/drbd.d/global_common.conf global { usage-count yes; # minor-count dialog-refresh disable-ip-verification } common { handlers { pri-on-incon-degr "/usr/lib/drbd/notify-pri-on-incon-degr.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; pri-lost-after-sb "/usr/lib/drbd/notify-pri-lost-after-sb.sh; /usr/lib/drbd/notify-emergency-reboot.sh; echo b /proc/sysrq-trigger ; reboot -f"; local-io-error "/usr/lib/drbd/notify-io-error.sh; /usr/lib/drbd/notify-emergency-shutdown.sh; echo o /proc/sysrq-trigger ; halt -f"; # fence-peer "/usr/lib/drbd/crm-fence-peer.sh"; # split-brain "/usr/lib/drbd/notify-split-brain.sh root"; # out-of-sync "/usr/lib/drbd/notify-out-of-sync.sh root"; # before-resync-target "/usr/lib/drbd/snapshot-resync-target-lvm.sh -p 15 -- -c 16k"; # after-resync-target /usr/lib/drbd/unsnapshot-resync-target-lvm.sh; } startup { # wfc-timeout degr-wfc-timeout outdated-wfc-timeout wait-after-sb become-primary-on both; wfc-timeout 30; degr-wfc-timeout 10; outdated-wfc-timeout 10; } options { # cpu-mask on-no-data-accessible } disk { # size max-bio-bvecs on-io-error fencing disk-barrier disk-flushes # disk-drain md-flushes resync-rate resync-after al-extents # c-plan-ahead c-delay-target c-fill-target c-max-rate # c-min-rate disk-timeout } net { # protocol timeout max-epoch-size max-buffers unplug-watermark # connect-int ping-int sndbuf-size rcvbuf-size ko-count # allow-two-primaries cram-hmac-alg shared-secret after-sb-0pri # after-sb-1pri after-sb-2pri always-asbp rr-conflict # ping-timeout data-integrity-alg tcp-cork on-congestion # congestion-fill congestion-extents csums-alg verify-alg # use-rle protocol C; allow-two-primaries yes; after-sb-0pri discard-zero-changes; after-sb-1pri discard-secondary; after-sb-2pri disconnect; } } cat /etc/drbd.d/storage.res resource storage { device /dev/drbd0; meta-disk internal; on host.structuralcomponents.net { address 10.10.1.120:7788; disk /dev/vg_storage/lv_storage; } on host2.structuralcomponents.net { address 10.10.1.121:7788; disk /dev/vg_storage/lv_storage; } /var/log/messages is not logging anything about the crash. I've been trying to find a cause of this but I've come up with nothing. Can anyone help me out? Thanks.

    Read the article

  • Postfix on Snow Leopard unable to send MIME emails, including header contents in message body

    - by devvy
    I configured postfix on snow leopard by adding the following line to /etc/hostconfig: MAILSERVER=-YES- I then configured postfix to relay through my ISP's SMTP server. I added the following two lines in their respective places within /etc/postfix/main.cf: myhostname = 1and1.com relayhost = shawmail.vc.shawcable.net I then have a simple PHP mail function wrapper as follows: send_email("[email protected]", "[email protected]", "Test Email", "<p>This is a simple HTML email</p>"); echo "Done"; function send_email($from,$to,$subject,$message){ $header="From: <".$from."> "; $header.= 'MIME-Version: 1.0' . " "; $header.= 'Content-type: text/html; charset=iso-8859-1' . " "; $send_mail=mail($to,$subject,$message,$header); if(!$send_mail){ echo "ERROR"; } } With this, I am receiving an e-mail that appears to be improperly formatted. The message header is showing up in the body of the e-mail. The raw message content is as follows: Return-Path: <[email protected]> Delivery-Date: Tue, 27 Apr 2010 18:12:48 -0400 Received: from idcmail-mo2no.shaw.ca (idcmail-mo2no.shaw.ca [64.59.134.9]) by mx.perfora.net (node=mxus2) with ESMTP (Nemesis) id 0M4XlU-1NCtC81GVY-00z5UN for [email protected]; Tue, 27 Apr 2010 18:12:48 -0400 Message-Id: <[email protected]> Received: from pd6ml3no-ssvc.prod.shaw.ca ([10.0.153.149]) by pd6mo1no-svcs.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:47 -0600 X-Cloudmark-SP-Filtered: true X-Cloudmark-SP-Result: v=1.0 c=1 a=VphdPIyG4kEA:10 a=hATtCjKilyj9ZF5m5A62ag==:17 a=mC_jT1gcAAAA:8 a=QLyc3QejAAAA:8 a=DGW4GvdtALggLTu6w9AA:9 a=KbDtEDGyCi7QHcNhDYYwsF92SU8A:4 a=uch7kV7NfGgA:10 a=5ZEL1eDBWGAA:10 Received: from unknown (HELO 1and1.com) ([24.84.196.104]) by pd6ml3no-dmz.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:48 -0600 Received: by 1and1.com (Postfix, from userid 70) id BB08D14ECFC; Tue, 27 Apr 2010 15:12:47 -0700 (PDT) To: [email protected] Subject: Test Email X-PHP-Originating-Script: 501:test.php Date: Tue, 27 Apr 2010 18:12:48 -0400 X-UI-Junk: AutoMaybeJunk +30 (SPA); V01:LYI2BGRt:7TwGx5jxe8cylj5nOTae9JQXYqoWvG2w4ZSfwYCXmHCH/5vVNCE fRD7wNNM86txwLDTO522ZNxyNHhvJUK9d2buMQuAUCMoea2jJHaDdtRgkGxNSkO2 v6svm0LsZikLMqRErHtBCYEWIgxp2bl0W3oA3nIbtfp3li0kta27g/ZjoXcgz5Sw B8lEqWBqKWMSta1mCM+XD/RbWVsjr+LqTKg== Envelope-To: [email protected] From: <[email protected]> MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 Message-Id: <[email protected]> Date: Tue, 27 Apr 2010 15:12:47 -0700 (PDT) <p>This is a simple HTML email</p> And here are the contents of my /var/log/mail.log file after sending the email: Apr 27 15:29:01 User-iMac postfix/qmgr[705]: 74B1514EDDF: removed Apr 27 15:29:30 User-iMac postfix/pickup[704]: 25FBC14EDF0: uid=70 from=<_www> Apr 27 15:29:30 User-iMac postfix/master[758]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable Apr 27 15:29:30 User-iMac postfix/cleanup[745]: 25FBC14EDF0: message-id=<[email protected]> Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: from=<[email protected]>, size=423, nrcpt=1 (queue active) Apr 27 15:29:30 User-iMac postfix/smtp[747]: 25FBC14EDF0: to=<[email protected]>, relay=shawmail.vc.shawcable.net[64.59.128.135]:25, delay=0.21, delays=0.01/0/0.1/0.1, dsn=2.0.0, status=sent (250 ok: Message 25784419 accepted) Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: removed Two other people in the office have followed the exact same process and are running the exact same script, version of snow leopard, php, etc. and everything is working fine for them. I've even copied their config files to my machine, restarted postfix, restarted apache, all to no avail. Does anyone know what steps I could take to resolve the issue? This is boggling my mind... Thanks

    Read the article

  • How to prevent delays associated with IPv6 AAAA records?

    - by Nic
    Our Windows servers are registering IPv6 AAAA records with our Windows DNS servers. However, we don't have IPv6 routing enabled on our network, so this frequently causes stall behaviours. Microsoft RDP is the worst offender. When connecting to a server that has a AAAA record in DNS, the remote desktop client will try IPv6 first, and won't fall back to IPv4 until the connection times out. Power users can work around this by connecting to the IP address directly. Resolving the IPv4 address with ping -4 hostname.foo always works instantly. What can I do to avoid this delay? Disable IPv6 on client? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Too many clients to ensure this is set everywhere consistently. Will cause more problems later when we finally implement IPv6. Disable IPv6 on the server? Nope, Microsoft says IPv6 is a mandatory part of the Windows operating system. Requires an inconvenient registry hack to disable the entire IPv6 stack. Ensuring this is correctly set on all servers is inconvenient. Will cause more problems later when we finally implement IPv6. Mask IPv6 records on the user-facnig DNS recursor? Nope, we're using NLNet Unbound and it doesn't support that. Prevent registration of IPv6 AAAA records on the Microsoft DNS server? I don't think that's even possible. At this point, I'm considering writing a script that purges all AAAA records from our DNS zones. Please, help me find a better way. UPDATE: DNS resolution is not the problem. As @joeqwerty points out in his answer, the DNS records are returned instantly. Both A and AAAA records are immediately available. The problem is that some clients (mstsc.exe) will preferentially attempt a connection over IPv6, and take a while to fall back to IPv4. This seems like a routing problem. The ping command produces a "General failure" error message because the destination address is unroutable. C:\Windows\system32>ping myhost.mydomain Pinging myhost.mydomain [2002:1234:1234::1234:1234] with 32 bytes of data: General failure. General failure. General failure. General failure. Ping statistics for 2002:1234:1234::1234:1234: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), I can't get a packet capture of this behaviour. Running this (failing) ping command does not produce any packets in Microsoft Network Monitor. Similarly, attempting a connection with mstsc.exe to a host with an AAAA record produces no traffic until it does a fallback to IPv4. UPDATE: Our hosts are all using publicly-routable IPv4 addresses. I think this problem might come down to a broken 6to4 configuration. 6to4 behaves differently on hosts with public IP addresses vs RFC1918 addresses. UPDATE: There is definitely something fishy with 6to4 on my network. When I disable 6to4 on the Windows client, connections resolve instantly. netsh int ipv6 6to4 set state disabled But as @joeqwerty says, this only masks the problem. I'm still trying to find out why IPv6 communication on our network is completely non-working.

    Read the article

  • smartctl -t long isn't finishing

    - by xenoterracide
    I been running smartctl -t long on a drive for about 2 days now and it seems to be stalled at 10%. short and conveyance both passed. I have to send 1 of 2 drives purchased back I found badblocks with badblocks (none on this drive and I'ts made over a pass already). I'm just wondering if I should be concerned about this. smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: WDC WD10EARS-00Y5B1 Serial Number: WD-WMAV51582123 Firmware Version: 80.00A80 User Capacity: 1,000,204,886,016 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon May 10 22:19:52 2010 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 241) Self-test routine in progress... 10% of test remaining. Total time to complete Offline data collection: (20100) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 231) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3031) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 2 3 Spin_Up_Time 0x0027 131 131 021 Pre-fail Always - 6408 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 12 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 148 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 10 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 7 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 174 194 Temperature_Celsius 0x0022 106 102 000 Old_age Always - 41 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Conveyance offline Completed without error 00% 99 - # 2 Extended offline Interrupted (host reset) 10% 30 - # 3 Short offline Completed without error 00% 0 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.

    Read the article

  • Random Slow Response

    - by ARehman
    We have an ASP.NET MVC 1.0 application running on Windows Server 2008 – Standard (32 –bit), Dual Core Xeon (3.0 GHz), 2 G.B R.A.M. Most of the times application renders response in 3-4 seconds, but sometimes users get very late response and delay is up to 40 seconds or more than a minute. It happens in following way: User browsed a page, idle for 5, 10 or 15 minutes, tried to browse same page or some other. Now, there is a chance that he will see late response whereas the app pool is still up and running. This can happen with any arbitrary page. We have tried followings/observations. Moved the application to stand alone web server App Pool idle shutdown time is 60 minutes. There are no abrupt shut downs/restarts. CPU or memory doesn’t spike. No delays in SQL queries. Modified App Pool setting to run in classic-mode. It didn’t help. Plugged-in custom module to log all those requests which took more than 5 seconds to complete. It didn’t pick any request of interest. Enabled ‘Failed Request Tracing’ to log all those requests which take 20 or more seconds to complete. It didn’t log anything. Event Viewer, HTTPER log, W3SVC logs or WAS logs don’t indicate anything. HTTPERR only has ‘_ _ Timer_ConnectionIdle _ _’ entries. There is not much traffic to server. This can happen also if only two users are active. Next we captured TCP/IP terrific on both a user and server end with Wireshark and below are details in brief of this slowness: Browser sends a request for ~/User/Home/ (GET Request) by setting up a receiving end point using port 'wlbs(port-2504)'. I'm not sure if this could be a problem in some way that browser didn't hand-shake with the server first and assumed that last connection is still open, whereas, I browsed the same page 4 minutes ago and didn't perform any activity with site after that. If I see the HTTPERR log, it indicates that it has ‘_ _ Timer_ConnectionIdle _ _ _’ entry for my last activity with server. Browser (I was using Chrome) waits for any response from the server, doesn’t find any then starts retransmitting the same request using same end point after incrementing wait intervals, e.g. after 8, 18, 29, 40, 62, and 92 seconds. All these GET requests were received by server as well. But, server didn’t send any packet to client. Browser didn't see any response on the end point it set up in point 1, it opened a new end point 'optiwave-lm (port-2524)', did a hand shake with the server and transmitted the same request again. Server received, processed it, and returned successful response. What happened to earlier 6-7 requests? Whether they were passed on to HTTP.SYS or not? Why Failed Request Tracing not logged anything, we didn't find any clue yet. Server served the same page successfully just 4 minutes ago. Looking forward for more suggestions/solutions. -- Thanks

    Read the article

  • Centos/OVH: public IP on KVM virtual machine

    - by Sébastien
    Since a few days, I'm trying to configure my KVM vm to have a public IP address, without any success. First, I'm on OVH, and you need to know they don't allow networking from different mac addresses. I have so registered a virtual mac address associated with my failover IP Here's my configuration: Guest wanted IP: 46.105.40.x Host IP: 176.31.240.x Host configuration dummy0 interface: ifcfg-dummy0 BOOTPROTO=static IPADDR=10.0.0.1 NETMASK=255.0.0.0 ONBOOT=yes NM_CONTROLLED=no ARP=yes BRIDGE=br0 br0 bridge: ifcfg-br0 DEVICE=br0 TYPE=Bridge DELAY=0 ONBOOT=yes BOOTPROTO=static IPADDR=192.168.1.1 NETMASK=255.255.255.0 PEERDNS=yes NM_CONTROLLED=no ARP=yes Failover ip is redirected to the br0 bridge with ip route add 46.105.40.xxx dev br0 > cat /proc/sys/net/ipv4/ip_forward 1 > cat /proc/sys/net/ipv4/conf/vnet0/proxy_arp 1 > route -n Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 176.31.240.254 0.0.0.0 UG 0 0 0 eth0 46.105.40.x 0.0.0.0 255.255.255.255 UH 0 0 0 br0 176.31.240.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 Guest configuration: KVM: <interface type='bridge'> <mac address='02:00:00:30:22:05'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x06' function='0x0'/> </interface> I've borrowed most of the OVH configuration here (in french, http://guides.ovh.com/BridgeClient) for the guest configuration eth0 interface: ifcfg-eth0 DEVICE="eth0" BOOTPROTO=none HWADDR="02:00:00:30:22:05" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" UUID="e9138469-0d81-4ee6-b5ab-de0d7d17d1c8" USERCTL=no PEERDNS=yes IPADDR=46.105.40.xxx NETMASK=255.255.255.255 GATEWAY=176.31.240.254 ARP=yes For the routes, I have in route-eth0: 176.31.240.254 dev eth0 default via 176.31.240.254 dev eth0 With this configuration, I don't have any access to the internet. The only thing I can do is to ping the public ip of the host, nothing more. My final conclusion is that the route does not work, because, when, on the guest, I run ping 8.8.8.8, I have, on the host: > tcpdump -i vnet0 icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on br0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:38:09.009324 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50183, seq 1, length 64 13:38:09.815344 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50183, seq 2, length 64 I never get the ping reply, only the request. It seems Guest - Host communication is fine. On eth0: > tcpdump -i eth0 icmp tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 13:39:40.240561 IP 46-105-40-xxx.kimsufi.com > google-public-dns-a.google.com: ICMP echo request, id 50439, seq 1, length 64 13:39:40.250161 IP google-public-dns-a.google.com > 46-105-40-xxx.kimsufi.com: ICMP echo reply, id 50439, seq 1, length 64 I have the request and the reply on eth0, but reply is not forwarded to the bridge. I really don't understand why, I though it was the aim of the route to do that! IPtables is disabled on both host and guest. I really hope some of you will be able to help me! Many thanks in advance, Sébastien

    Read the article

  • Oracle Virtual Server OEL vm fails to start - kernel panic on cpu identify

    - by Towndrunk
    I am in the process of following a guide to setup various oracle vm templates, so far I have installed OVS 2. 2 and got the OVM Manager working, imported the template for OEL5U5 and created a vm from it.. the problem comes when starting that vm. The log in the OVMM console shows the following; Update VM Status - Running Configure CPU Cap Set CPU Cap: failed:<Exception: failed:<Exception: ['xm', 'sched-credit', '-d', '32_EM11g_OVM', '-c', '0'] => Error: Domain '32_EM11g_OVM' does not exist. StackTrace: File "/opt/ovs-agent-2.3/OVSXXenVMConfig.py", line 2531, in xen_set_cpu_cap run_cmd(args=['xm', File "/opt/ovs-agent-2.3/OVSCommons.py", line 92, in run_cmd raise Exception('%s => %s' % (args, err)) The xend.log shows; [2012-11-12 16:42:01 7581] DEBUG (DevController:139) Waiting for devices vtpm [2012-11-12 16:42:01 7581] INFO (XendDomain:1180) Domain 32_EM11g_OVM (3) unpaused. [2012-11-12 16:42:03 7581] WARNING (XendDomainInfo:1907) Domain has crashed: name=32_EM11g_OVM id=3. [2012-11-12 16:42:03 7581] ERROR (XendDomainInfo:2041) VM 32_EM11g_OVM restarting too fast (Elapsed time: 11.377262 seconds). Refusing to restart to avoid loops .> [2012-11-12 16:42:03 7581] DEBUG (XendDomainInfo:2757) XendDomainInfo.destroy: domid=3 [2012-11-12 16:42:12 7581] DEBUG (XendDomainInfo:2230) Destroying device model [2012-11-12 16:42:12 7581] INFO (image:553) 32_EM11g_OVM device model terminated I have set_on_crash="preserve" in the vm.cfg and have then run xm create -c to get the console screen while booting and this is the log of what happens.. Started domain 32_EM11g_OVM (id=4) Bootdata ok (command line is ro root=LABEL=/ ) Linux version 2.6.18-194.0.0.0.3.el5xen ([email protected]) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Mon Mar 29 18:27:00 EDT 2010 BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000180800000 (usable)> No mptable found. Built 1 zonelists. Total pages: 1574912 Kernel command line: ro root=LABEL=/ Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Xen reported: 1600.008 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) Software IO TLB disabled Memory: 6155256k/6299648k available (2514k kernel code, 135548k reserved, 1394k data, 184k init) Calibrating delay using timer specific routine.. 4006.42 BogoMIPS (lpj=8012858) Security Framework v1.0.0 initialized SELinux: Initializing. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 16K (64 bytes/line) CPU: L2 Cache: 2048K (64 bytes/line) general protection fault: 0000 [1] SMP last sysfs file: CPU 0 Modules linked in: Pid: 0, comm: swapper Not tainted 2.6.18-194.0.0.0.3.el5xen #1 RIP: e030:[ffffffff80271280] [ffffffff80271280] identify_cpu+0x210/0x494 RSP: e02b:ffffffff80643f70 EFLAGS: 00010212 RAX: 0040401000810008 RBX: 0000000000000000 RCX: 00000000c001001f RDX: 0000000000404010 RSI: 0000000000000001 RDI: 0000000000000005 RBP: ffffffff8063e980 R08: 0000000000000025 R09: ffff8800019d1000 R10: 0000000000000026 R11: ffff88000102c400 R12: 0000000000000000 R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 FS: 0000000000000000(0000) GS:ffffffff805d2000(0000) knlGS:0000000000000000 CS: e033 DS: 0000 ES: 0000 Process swapper (pid: 0, threadinfo ffffffff80642000, task ffffffff804f4b80) Stack: 0000000000000000 ffffffff802d09bb ffffffff804f4b80 0000000000000000 0000000021100800 0000000000000000 0000000000000000 ffffffff8064cb00 0000000000000000 0000000000000000 Call Trace: [ffffffff802d09bb] kmem_cache_zalloc+0x62/0x80 [ffffffff8064cb00] start_kernel+0x210/0x224 [ffffffff8064c1e5] _sinittext+0x1e5/0x1eb Code: 0f 30 b8 73 00 00 00 f0 0f ab 45 08 e9 f0 00 00 00 48 89 ef RIP [ffffffff80271280] identify_cpu+0x210/0x494 RSP ffffffff80643f70 0 Kernel panic - not syncing: Fatal exception clear as mud to me. are there any other logs that will help me? I have now deployed another vm from the same template and used the default vm settings rather than adding more memory etc - I get exactly the same error.

    Read the article

  • Centos 7. Freeradius fails to start on boot

    - by Alex
    I was messing around with FreeRADIUS and MySQL (MariaDB) and it seems FreeRADIUS service can't start properly on startup. But it starts fine using root user or in debug mode (radiusd -X) and works just fine! Debug mode shows no errors. systemctl command shows that radiusd.service has failed to start. /var/log/messages output: Aug 21 15:52:29 nexus-test systemd: Starting The Apache HTTP Server... Aug 21 15:52:29 nexus-test systemd: Starting MariaDB database server... Aug 21 15:52:29 nexus-test systemd: Starting FreeRADIUS high performance RADIUS server.... Aug 21 15:52:29 nexus-test systemd: Started OpenSSH server daemon. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Logging to '/var/log/mariadb/mariadb.log'. Aug 21 15:52:29 nexus-test mysqld_safe: 140821 15:52:29 mysqld_safe Starting mysqld daemon with databases from /var/lib/mysql Aug 21 15:52:30 nexus-test systemd: Started Postfix Mail Transport Agent. Aug 21 15:52:30 nexus-test avahi-daemon[604]: Registering new address record for fe80::250:56ff:fe85:e4af on eth0.*. Aug 21 15:52:30 nexus-test systemd: radiusd.service: control process exited, code=exited status=1 Aug 21 15:52:30 nexus-test systemd: Failed to start FreeRADIUS high performance RADIUS server.. Aug 21 15:52:30 nexus-test systemd: Unit radiusd.service entered failed state. Aug 21 15:52:31 nexus-test kdumpctl: kexec: loaded kdump kernel Aug 21 15:52:31 nexus-test kdumpctl: Starting kdump: [OK] Aug 21 15:52:31 nexus-test systemd: Started Crash recovery kernel arming. Aug 21 15:52:31 nexus-test systemd: Started The Apache HTTP Server. Aug 21 15:52:31 nexus-test systemd: Started MariaDB database server. /var/log/radius/radius.log output: Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Driver rlm_sql_mysql (module rlm_sql_mysql) loaded and linked Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Attempting to connect to database "radius" Thu Aug 21 15:24:16 2014 : Info: rlm_sql (sql): Opening additional connection (0) Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Couldn't connect socket to MySQL server radius@localhost:radius Thu Aug 21 15:24:16 2014 : Error: rlm_sql_mysql: Mysql error 'Can't connect to local MySQL server through socket '/var/lib/mysql/mysql.sock' (2)' Thu Aug 21 15:24:16 2014 : Error: rlm_sql (sql): Opening connection failed (0) Thu Aug 21 15:24:16 2014 : Error: /etc/raddb/mods-enabled/sql[47]: Instantiation failed for module "sql" After seeing this I tried to replicate the problem, killed mariadb.service and started to run debug mode again. And it spits out the same problem as in the radius.log. I tried disabling iptables and firewalld and rebooting, but no luck: systemctl disable iptables systemctl disable firewalld So maybe the problem is in the process startup order or delay of some kind. Maybe FreeRADIUS's SQL module can't connect to not yet started MariaDB? If it, how can I fix this? In earlier versions of RHEL/CENTOS I know you easily see service start order in like rc.d or stuff, now IDK. I am new to this fancy "systemd", "systemctl", "firewalld" stuff Centos 7 introduced so sorry I'm a little bit confused. Also this new FreeRADIUS 3 structure... PS. MariaDB is enabled on startup, credentials in FR DB configuration are correct A little update: cat /etc/systemd/system/multi-user.target.wants/radiusd.service output: [Unit] Description=FreeRADIUS high performance RADIUS server. After=syslog.target network.target [Service] Type=forking PIDFile=/var/run/radiusd/radiusd.pid ExecStartPre=-/bin/chown -R radiusd.radiusd /var/run/radiusd ExecStartPre=/usr/sbin/radiusd -C ExecStart=/usr/sbin/radiusd -d /etc/raddb ExecReload=/usr/sbin/radiusd -C ExecReload=/bin/kill -HUP $MAINPID [Install] WantedBy=multi-user.target

    Read the article

  • Proliant server will not accept new hard disks in RAID 1+0?

    - by Leigh
    I have a HP ProLiant DL380 G5, I have two logical drives configured with RAID. I have one logical drive RAID 1+0 with two 72 gb 10k sas 1 port spare no 376597-001. I had one hard disk fail and ordered a replacement. The configuration utility showed error and would not rebuild the RAID. I presumed a hard disk fault and ordered a replacement again. In the mean time I put the original failed disk back in the server and this started rebuilding. Currently shows ok status however in the log I can see hardware errors. The new disk has come and I again have the same problem of not accepting the hard disk. I have updated the P400 controller with the latest firmware 7.24 , but still no luck. The only difference I can see is the original drive has firmware 0103 (same as the RAID drive) and the new one has HPD2. Any advice would be appreciated. Thanks in advance Logs from server ctrl all show config Smart Array P400 in Slot 1 (sn: PAFGK0P9VWO0UQ) array A (SAS, Unused Space: 0 MB) logicaldrive 1 (68.5 GB, RAID 1, Interim Recovery Mode) physicaldrive 2I:1:1 (port 2I:box 1:bay 1, SAS, 73.5 GB, OK) physicaldrive 2I:1:2 (port 2I:box 1:bay 2, SAS, 72 GB, Failed array B (SAS, Unused Space: 0 MB) logicaldrive 2 (558.7 GB, RAID 5, OK) physicaldrive 1I:1:5 (port 1I:box 1:bay 5, SAS, 300 GB, OK) physicaldrive 2I:1:3 (port 2I:box 1:bay 3, SAS, 300 GB, OK) physicaldrive 2I:1:4 (port 2I:box 1:bay 4, SAS, 300 GB, OK) ctrl all show config detail Smart Array P400 in Slot 1 Bus Interface: PCI Slot: 1 Serial Number: PAFGK0P9VWO0UQ Cache Serial Number: PA82C0J9VWL8I7 RAID 6 (ADG) Status: Disabled Controller Status: OK Hardware Revision: E Firmware Version: 7.24 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Status Details: A cache error was detected. Run more information. Cache Ratio: 100% Read / 0% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Battery/Capacitor Count: 0 SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 0 MB Status: Failed Physical Drive Array Type: Data One of the drives on this array have failed or has Logical Drive: 1 Size: 68.5 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 17594 Strip Size: 128 KB Full Stripe Size: 128 KB Status: Interim Recovery Mode Caching: Enabled Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive0 Mount Points: C:\ 68.5 GB Logical Drive Label: A0100539PAFGK0P9VWO0UQ0E93 Mirror Group 0: physicaldrive 2I:1:2 (port 2I:box 1:bay 2, S Mirror Group 1: physicaldrive 2I:1:1 (port 2I:box 1:bay 1, S Drive Type: Data physicaldrive 2I:1:1 Port: 2I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 73.5 GB Rotational Speed: 10000 Firmware Revision: 0103 Serial Number: B379P8C006RK Model: HP DG072A9B7 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:2 Port: 2I Box: 1 Bay: 2 Status: Failed Drive Type: Data Drive Interface Type: SAS Size: 72 GB Rotational Speed: 15000 Firmware Revision: HPD9 Serial Number: D5A1PCA04SL01244 Model: HP EH0072FARUA PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data Logical Drive: 2 Size: 558.7 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Co Unique Identifier: 600508B10010503956574F305551 Disk Name: \\.\PhysicalDrive1 Mount Points: E:\ 558.7 GB Logical Drive Label: AF14FD12PAFGK0P9VWO0UQD007 Drive Type: Data physicaldrive 1I:1:5 Port: 1I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE07QH300009923X1X3 Model: HP DG0300BALVP Current Temperature (C): 32 Maximum Temperature (C): 45 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:3 Port: 2I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE0AHVH00009924P8F3 Model: HP DG0300BALVP Current Temperature (C): 34 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:4 Port: 2I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 300 GB Rotational Speed: 10000 Firmware Revision: HPD4 Serial Number: 3SE08NAK00009924KWD6 Model: HP DG0300BALVP Current Temperature (C): 35 Maximum Temperature (C): 47 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown

    Read the article

  • "Possible SYN flooding" in log despite low number of SYN_RECV connections

    - by al4
    Recently we had an apache server which was responding very slowly due to SYN flooding. The workaround for this was to enable tcp_syncookies (net.ipv4.tcp_syncookies=1 in /etc/sysctl.conf). I posted a question about this here if you want more background. After enabling syncookies we started seeing the following message in /var/log/messages approximately every 60 seconds: [84440.731929] possible SYN flooding on port 80. Sending cookies. Vinko Vrsalovic informed me that this means the syn backlog is getting full, so I raised tcp_max_syn_backlog to 4096. At some point I also lowered tcp_synack_retries to 3 (down from the default of 5) by issuing sysctl -w net.ipv4.tcp_synack_retries=3. After doing this, the frequency seemed to drop, with the interval of the messages varying between roughly 60 and 180 seconds. Next I issued sysctl -w net.ipv4.tcp_max_syn_backlog=65536, but am still getting the message in the log. Throughout all this I've been watching the number of connections in SYN_RECV state (by running watch --interval=5 'netstat -tuna |grep "SYN_RECV"|wc -l'), and it never goes higher than about 240, much much lower than the size of the backlog. Yet I have a Red Hat server which hovers around 512 (limit on this server is the default of 1024). Are there any other tcp settings which would limit the size of the backlog or am I barking up the wrong tree? Should the number of SYN_RECV connections in netstat -tuna correlate to the size of the backlog? Update As best I can tell I'm dealing with legitimate connections here, netstat -tuna|wc -l hovers around 5000. I've been researching this today and found this post from a last.fm employee, which has been rather useful. I've also discovered that the tcp_max_syn_backlog has no effect when syncookies are enabled (as per this link) So as a next step I set the following in sysctl.conf: net.ipv4.tcp_syn_retries = 3 # default=5 net.ipv4.tcp_synack_retries = 3 # default=5 net.ipv4.tcp_max_syn_backlog = 65536 # default=1024 net.core.wmem_max = 8388608 # default=124928 net.core.rmem_max = 8388608 # default=131071 net.core.somaxconn = 512 # default = 128 net.core.optmem_max = 81920 # default = 20480 I then setup my response time test, ran sysctl -p and disabled syncookies by sysctl -w net.ipv4.tcp_syncookies=0. After doing this the number of connections in the SYN_RECV state still remained around 220-250, but connections were starting to delay again. Once I noticed these delays I re-enabled syncookies and the delays stopped. I believe what I was seeing was still an improvement from the initial state, however some requests were still delayed which is much worse than having syncookies enabled. So it looks like I'm stuck with them enabled until we can get some more servers online to cope with the load. Even then, I'm not sure I see a valid reason to disable them again as they're only sent (apparently) when the server's buffers get full. But the syn backlog doesn't appear to be full with only ~250 connections in the SYN_RECV state! Is it possible that the SYN flooding message is a red herring and it's something other than the syn_backlog that's filling up? If anyone has any other tuning options I haven't tried yet I'd be more than happy to try them out, but I'm starting to wonder if the syn_backlog setting isn't being applied properly for some reason.

    Read the article

  • unattended-upgrades does not reboot

    - by Cheiron
    I am running Debian 7 stable with unattended-upgrades (every morning at 6 AM) to make sure I am always fully updated. I have the following config: $ cat /etc/apt/apt.conf.d/50unattended-upgrades // Automatically upgrade packages from these origin patterns Unattended-Upgrade::Origins-Pattern { // Archive or Suite based matching: // Note that this will silently match a different release after // migration to the specified archive (e.g. testing becomes the // new stable). "o=Debian,a=stable"; "o=Debian,a=stable-updates"; // "o=Debian,a=proposed-updates"; "origin=Debian,archive=stable,label=Debian-Security"; }; // List of packages to not update Unattended-Upgrade::Package-Blacklist { // "vim"; // "libc6"; // "libc6-dev"; // "libc6-i686"; }; // This option allows you to control if on a unclean dpkg exit // unattended-upgrades will automatically run // dpkg --force-confold --configure -a // The default is true, to ensure updates keep getting installed //Unattended-Upgrade::AutoFixInterruptedDpkg "false"; // Split the upgrade into the smallest possible chunks so that // they can be interrupted with SIGUSR1. This makes the upgrade // a bit slower but it has the benefit that shutdown while a upgrade // is running is possible (with a small delay) //Unattended-Upgrade::MinimalSteps "true"; // Install all unattended-upgrades when the machine is shuting down // instead of doing it in the background while the machine is running // This will (obviously) make shutdown slower //Unattended-Upgrade::InstallOnShutdown "true"; // Send email to this address for problems or packages upgrades // If empty or unset then no email is sent, make sure that you // have a working mail setup on your system. A package that provides // 'mailx' must be installed. E.g. "[email protected]" Unattended-Upgrade::Mail "root"; // Set this value to "true" to get emails only on errors. Default // is to always send a mail if Unattended-Upgrade::Mail is set Unattended-Upgrade::MailOnlyOnError "true"; // Do automatic removal of new unused dependencies after the upgrade // (equivalent to apt-get autoremove) //Unattended-Upgrade::Remove-Unused-Dependencies "false"; // Automatically reboot *WITHOUT CONFIRMATION* if a // the file /var/run/reboot-required is found after the upgrade Unattended-Upgrade::Automatic-Reboot "true"; // Use apt bandwidth limit feature, this example limits the download // speed to 70kb/sec //Acquire::http::Dl-Limit "70"; As you can see Automatic-Reboot is true and thus the server should automaticly reboot. Last time I checked the server was online for over 100 days, which means that the update from Debian 7.1 to Debian 7.2 has happened while the server was up (and indeed, all updates were installed), but this involves kernel updates, which means that the server should reboot. It did not. The server was running very slow, so I rebooted which fixed that. I did some research and found out that unattended-upgrades responds to the reboot-required file in /var/run/. I touched this file and waited one week, the file still exists and the server did not reboot. So I think that unattended-uppgrades ignores the auto-reboot part. So, am I doing somthing wrong here? Why did the server not restart? The upgrade part works perfect by the way, its just the reboot part that does not seem to work as it should.

    Read the article

  • Postfix logs missing information on delivery status (postfix/smtp message)

    - by hegemon
    I noticed a problem with postfix logs, that information on some of emails delivery status is missing. The issue affects about 1% of emails. "Healthy" log: <server># grep 8EB992EFBB44 postfix_log/mail04.log Jun 5 03:09:29 mail04 postfix/smtpd[8537]: 8EB992EFBB44: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 03:09:29 mail04 postfix/cleanup[34349]: 8EB992EFBB44: message-id=<[email protected]> Jun 5 03:12:02 mail04 postfix/qmgr[76377]: 8EB992EFBB44: from=<[email protected]>, size=48845, nrcpt=1 (queue active) Jun 5 03:15:12 mail04 postfix/smtp[35058]: 8EB992EFBB44: to=<[email protected]>, relay=mx.baz.com[xxx.xxx.xxx.xxx]:25, conn_use=70, delay=343, delays=153/190/0/0.24, dsn=2.0.0, status=sent (250 ok) Jun 5 03:15:12 mail04 postfix/qmgr[76377]: 8EB992EFBB44: removed "Broken" log: <server># grep F3C362EF37CA postfix_log/mail04.log Jun 5 04:03:27 mail04 postfix/smtpd[39666]: F3C362EF37CA: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 5 04:03:27 mail04 postfix/cleanup[41287]: F3C362EF37CA: message-id=<[email protected]> Jun 5 04:03:28 mail04 postfix/qmgr[76377]: F3C362EF37CA: from=<[email protected]>, size=48892, nrcpt=1 (queue active) ** here should be a log line from postfix/smtp but there is none ** Jun 5 04:03:29 mail04 postfix/qmgr[76377]: F3C362EF37CA: removed Background information: system: FreeBSD xxx.xxx.xxx 8.2-RELEASE FreeBSD 8.2-RELEASE #0: Thu Feb 17 02:41:51 UTC 2011 [email protected]:/usr/obj/usr/src/sys/GENERIC amd64 Postfix is installed inside jail. Logs are on the same machine, log dir is mounted thru nullfs. The site has spikes of heavy load, causing disks (local) to run at 100%. Update The log is rotated daily, current size is ~ 500MB. I made a test by queuing 99000 messages to same destination (in order to rule out dns/network/mx issues). 5715 messages don't have any DSN record. Failed messages queue time is spread evenly over time, i don't see any time-bound issues. Some undelivered emails: envelopeid | processed_time --------------+---------------------------- 8D7652EF3BAE | 2012-06-06 13:19:11.072715 DD53A2EF3C5C | 2012-06-06 13:33:24.374783 8C52F2EF4E3F | 2012-06-06 13:39:15.810616 BBC572EF525C | 2012-06-06 13:44:22.762812 E95822EF54D1 | 2012-06-06 13:52:01.134533 839DD2EF4FBB | 2012-06-06 14:13:48.511236 017EE2EF6234 | 2012-06-06 15:04:48.618963 Those are a few picks, such records of undelivered email occur almost every second. <server># egrep '(8D7652EF3BAE|BBC572EF525C|017EE2EF6234)' mail04.log Jun 6 13:19:10 mail04 postfix/smtpd[20350]: 8D7652EF3BAE: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:19:10 mail04 postfix/cleanup[21024]: 8D7652EF3BAE: message-id=<[email protected]> Jun 6 13:19:10 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: from=<[email protected]>, size=63718, nrcpt=1 (queue active) Jun 6 13:19:11 mail04 postfix/qmgr[7939]: 8D7652EF3BAE: removed Jun 6 13:44:22 mail04 postfix/smtpd[20346]: BBC572EF525C: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 13:44:22 mail04 postfix/cleanup[24811]: BBC572EF525C: message-id=<[email protected]> Jun 6 13:44:22 mail04 postfix/qmgr[7939]: BBC572EF525C: from=<[email protected]>, size=63758, nrcpt=1 (queue active) Jun 6 15:04:49 mail04 postfix/smtpd[20344]: 017EE2EF6234: client=xxx.xxx.xxx[xxx.xxx.xxx.xxx] Jun 6 15:04:49 mail04 postfix/cleanup[35585]: 017EE2EF6234: message-id=<[email protected]> Jun 6 15:04:49 mail04 postfix/qmgr[7939]: 017EE2EF6234: from=<[email protected]>, size=63706, nrcpt=1 (queue active) <server># <server># find /var/spool/postfix/active/ -type f -print | wc -l 1 <server># IMPORTANT: As you can see above some of emails doesn't event have the removed line.

    Read the article

  • cannot send mail to postfix /w iptables linux proxy

    - by Juzzam
    I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

    Read the article

  • Why don't mails show up in the recipient's mailspool?

    - by Jason
    I have postfix dovecot running with local email system on thunderbird. I have two users on by ubuntu, mailuser 1 and mailuser 2 whom i added to thunderbird. Everything went fine, except the users dont have anything on their inbox on thunderbird and sent mails dont get through. Im using maildir as well. Checking /var/log/mail.log reveals this This what is happining: Restarting postfix and dovecot and then sending mail from one user to another user... I believe this line is the problem May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] Why is it not connecting ? What could be wrong ? /var/log/mail.log May 30 18:30:21 dovecot: imap: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: imap: Server shutting down. in=467 out=475 May 30 18:30:21 dovecot: config: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: log: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: anvil: Warning: Killed with signal 15 (by pid=1 uid=0 code=kill) May 30 18:30:21 dovecot: master: Dovecot v2.2.9 starting up (core dumps disabled) May 30 18:30:54 dovecot: imap-login: Login: user=<mailuser2>, method=PLAIN, rip=::1, lip=::1, mpid=12638, TLS, session=<xUfQkaD66gAAAAAAAAAAAAAAAAAAAAAB> May 30 18:31:04 postfix/master[12245]: terminating on signal 15 May 30 18:31:04 postfix/master[12795]: daemon started -- version 2.11.0, configuration /etc/postfix May 30 18:31:55 postfix/postscreen[12803]: CONNECT from [127.0.0.1]:33668 to [127.0.0.1]:25 May 30 18:31:55 postfix/postscreen[12803]: WHITELISTED [127.0.0.1]:33668 May 30 18:31:55 postfix/smtpd[12804]: connect from localhost[127.0.0.1] May 30 18:31:55 postfix/smtpd[12804]: 1ED7120EB9: client=localhost[127.0.0.1] May 30 18:31:55 postfix/cleanup[12809]: 1ED7120EB9: message-id=<[email protected]> May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: from=<[email protected]>, size=546, nrcpt=1 (queue active) May 30 18:31:55 postfix/local[12810]: 1ED7120EB9: to=<mailuser2@mysitecom>, relay=local, delay=0.03, delays=0.02/0.01/0/0, dsn=2.0.0, status=sent (delivered to maildir) May 30 18:31:55 postfix/qmgr[12799]: 1ED7120EB9: removed May 30 18:31:55 postfix/smtpd[12804]: disconnect from localhost[127.0.0.1] May 30 18:31:55 dovecot: imap-login: Login: user=<mailuser1>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=12814, TLS, session=<sD9plaD6PgB/AAAB> This is my postfix main.cf See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. #myorigin = /etc/mailname smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file=/etc/ssl/private/ssl-cert-snakeoil.key smtpd_use_tls=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. smtpd_relay_restrictions = permit_mynetworks permit_sasl_authenticated defer_unauth_destination myhostname = server mydomain = mysite.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $mydomain mydestination = mysite.com #relayhost = smtp.192.168.10.1.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 192.168.10.0/24 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all home_mailbox = Maildir / mailbox_command= All ports are listening tcp 0 0 *:imaps *:* LISTEN tcp 0 0 *:submission *:* LISTEN tcp 0 0 *:imap2 *:* LISTEN tcp 0 0 s148134.s148134.:domain *:* LISTEN tcp 0 0 192.168.56.101:domain *:* LISTEN tcp 0 0 10.0.2.15:domain *:* LISTEN tcp 0 0 localhost:domain *:* LISTEN tcp 0 0 *:ssh *:* LISTEN tcp 0 0 *:smtp *:* LISTEN tcp 0 0 localhost:953 *:* LISTEN tcp6 0 0 [::]:imaps [::]:* LISTEN tcp6 0 0 [::]:submission [::]:* LISTEN tcp6 0 0 [::]:imap2 [::]:* LISTEN tcp6 0 0 [::]:domain [::]:* LISTEN tcp6 0 0 [::]:ssh [::]:* LISTEN tcp6 0 0 [::]:smtp [::]:* LISTEN tcp6 0 0 localhost:953 [::]:* LISTEN

    Read the article

  • cannot send mail to postfix /w iptables linux proxy

    - by Juzzam
    I have two separate servers, both running Ubuntu 8.04. Server 1 has the real domain name of our site, let's refer to it as example.com. Server 2 is a mail server I have setup with postfix/courier. The hostname for this server is mail.example.com. I've setup iptables on Server 1 to forward all traffic on port 25 to Server 2. I used this script (except I changed the target ip address and the port from 80 to 25). When I send an email to [email protected] it works. However, when I try to send an email to [email protected] from gmail, I get this error: 550 550 #5.1.0 Address rejected [email protected] (state 14) /var/log/mail.log shows no new lines when this happens. What is strange is that it works with telnet from my local machine. For example: $ telnet example.com 25 220 VO13421.localdomain SMTP Postfix EHLO example.com 250-VO13421.localdomain 250-PIPELINING 250-SIZE 10240000 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN MAIL FROM: [email protected] 250 2.1.0 Ok RCPT TO: [email protected] 250 2.1.5 Ok data 354 Please start mail input. hello user... how have you been? . 250 Mail queued for delivery. quit 221 Closing connection. Good bye. /var/log/mail.log shows success (and the email goes to the maildr): Feb 24 09:47:36 VO13421 postfix/smtpd[2212]: connect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:01 VO13421 postfix/smtpd[2212]: 65C68120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: warning: restriction `smtpd_data_restrictions' after `permit' is ignored Feb 24 09:48:29 VO13421 postfix/smtpd[2212]: 6BDFA120321: client=81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] Feb 24 09:48:29 VO13421 postfix/cleanup[2216]: 6BDFA120321: message-id= Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: from=, size=395, nrcpt=1 (queue active) Feb 24 09:48:29 VO13421 postfix/virtual[2217]: 6BDFA120321: to=, relay=virtual, delay=0.28, delays=0.25/0.02/0/0.01, dsn=2.0.0, status=sent (delivered to maildir) Feb 24 09:48:29 VO13421 postfix/qmgr[2042]: 6BDFA120321: removed Feb 24 09:48:30 VO13421 postfix/smtpd[2212]: disconnect from 81.208.68.208.static.dnsptr.net[208.68.xxx.xxx] iptables -L -n -v --line on example.com yields the following. Anyone know an iptables command to see the port forwarding? Also, it seems to accept all traffic, that's probably bad right? ;] num pkts bytes target prot opt in out source destination 1 14041 1023K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 338 20722 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT 419K packets, 425M bytes) num pkts bytes target prot opt in out source destination 1 13711 2824K ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 postconf -n results in: alias_database = hash:/etc/postfix/aliases alias_maps = hash:/etc/postfix/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all local_recipient_maps = mailbox_size_limit = 0 masquerade_domains = mail.example.com mail1.example.com masquerade_exceptions = root maximal_backoff_time = 8000s maximal_queue_lifetime = 7d minimal_backoff_time = 1000s mydestination = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = example.com readme_directory = no recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname SMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_data_restrictions = reject_unauth_pipelining smtpd_sender_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/mysql_alias.cf virtual_gid_maps = mysql:/etc/postfix/mysql_gid.cf virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/mysql_domains.cf virtual_mailbox_maps = mysql:/etc/postfix/mysql_mailbox.cf virtual_uid_maps = mysql:/etc/postfix/mysql_uid.cf

    Read the article

  • ISP 5 Device Limit ... again

    - by Tommo
    Sorry for the delay in responding to the suggestions that were posted in my first question (ISP 5 Device Limit - double NAT the solution?). I've been travelling and have not been able to try anything. Below is what I've tried and where I have not been successful. Any more help gratefully appreciated. I figure I need to give a more comprehensive overview of what I've got and how it's set up. First of all - I am using all Apple products here. I am iMac, iPad, iPhone, Apple TV, Airport Express and Time Capsule. I used to like the way that it 'just worked'. Now I find that it requires a bit of encouragement before it 'just works'. So, as I stated in my original question; my ISP has a router in my building that is limiting me to 5 devices. I am hard wired into this router and I can neither access it physically nor logically (they won't let me access it). Also, I only appear to be able to connect to it through the LAN ports on my Time Capsule. Any device I connect appears to be on a rolling IP list with the following settings: Router 91.72.80.1 Devices then get assigned IPv4 addresses in the range (as far as I can see) from 91.72.80.2 onwards. SubNet Mask 255.255.255.0 DNS Servers 213.132.63.25, 80.227.2.4 I have my Time Capsule / Router in Bridge-Mode which means I am limited to the 5 devices and cannot use Guest Networks etc. What I've tried today. Static IPs: On all devices, I went from DHCP to Static and put in the same information when they had connected using DHCP. Somewhat surprisingly this did not work. None of the devices enjoyed any connection to the router and certainly no internet connection. Intentional Double-NAT - Time Capsule to 'DHCP and NAT': By selecting DHCP and NAT on my Router I was able to connect devices to my Time Capsule in the range 10.0.1.2 to 10.0.1.200. This offered no internet connectivity and didn't really help the situation. In this mode, however, I was able to force the devices - individually and laboriously - to look for the Router and previously listed DNSs by inputting the numbers from 'Bridge-mode' into the STATIC settings and then resetting the connection. The Router then appeared to assign a distinct IP address to the device and it worked on the network. I had this working for more than 5 devices. However, this is not a great solution because as soon as one of the mobile devices left the building it needed repointing to the Router. The connections were also not very stable. Especially when trying to hold onto a VPN. Spoofing a few MAC addresses: I'm afraid I don't really know what this would achieve, nor how to do it on an Apple device… So … I'm almost back at Square One. I have had to withdraw to the Bridge-Mode position again with the 5 device limit to see if there's a better course of action to follow. ANY help would be much appreciated. I am positive that I cannot be the only one suffering under this 5 device limit!

    Read the article

  • .Net DataGridView "Index 0 does not have a value."

    - by Ben
    I am having trouble with a DataGridView. I have a collection of 3 Items bound to the grid, when trying to delete one of the items and reload the grid. If have code of If (dlg.ShowDialog() = DialogResult.OK) Then 'Show dialog with grid on it End If On the opened dialog, I delete an item from the grid (which should in turn, delete the item from the collection, and re-load the grid), and it returns to the "If (dlg.show..." line, with the error of "A first chance exception of type 'System.IndexOutOfRangeException' occurred in System.Windows.Forms.dll Additional information: Index 2 does not have a value. " (I have break into debugger set on for common language runtime errors) I can understand this error if i were trying to access any cells, row or columns, but im not, and then I would expect the exception to stop on the line of code that is trying to access this grid data, not the "If (dlg.ShowDialog()... " line Any ideas? Cheers

    Read the article

  • CefSharp.BrowserSubprocess.exe has stopped working

    - by Amogh
    I have CefSharp-master project with which is Built on Chromium- 31.0.1650.57. All is working fine and perfect, but when I click on link to load/view PDF file on an website and popup get loaded and after some time I got dialog box saying "CefSharp.BrowserSubprocess.exe has stopped working." and oped popup window become black. Below is what I found in windows event viewer.. Application: CefSharp.BrowserSubprocess.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.AccessViolationException Stack: at <Module>.CefExecuteProcess(CefMainArgs*, CefRefPtr<CefApp>*) at CefSharp.CefAppWrapper.Run(System.String[]) at CefSharp.BrowserSubprocess.Program.Main(System.String[]) What is problem? I searched a lot but didn't find any think.

    Read the article

  • DataContractJsonSerializer ReadObject Exception

    - by Dan Appleyard
    I am following the accepted answer of ASP.NET MVC How to pass JSON object from View to Controller as Parameter. Like the original question, I have a simple POCO. Everthing works fine for me up until the DataContractJsonSerializer.ReadObject method. I am getting the following exception: Expecting element 'root' from namespace ''.. Encountered 'None' with name '', namespace ''. Public Overrides Sub OnActionExecuting(ByVal filterContext As ActionExecutingContext) If filterContext.HttpContext.Request.ContentType.Contains("application/json") Then Dim s As System.IO.Stream = filterContext.HttpContext.Request.InputStream Dim o = New DataContractJsonSerializer(RootType).ReadObject(s) filterContext.ActionParameters(Param) = o Else Dim xmlRoot = XElement.Load(New StreamReader(filterContext.HttpContext.Request.InputStream, filterContext.HttpContext.Request.ContentEncoding)) Dim o As Object = New XmlSerializer(RootType).Deserialize(xmlRoot.CreateReader) filterContext.ActionParameters(Param) = o End If End Sub Any ideas? Thanks

    Read the article

  • WPF TreeView databinding to hide/show expand/collapse icon

    - by Julian Lettner
    I implemented a WPF load-on-demand treeview like described in this (very good) article. In the mentioned solution a dummy element is used to preserve the expand + icon / treeview item behavior. The dummy item is replaced with real data, when the user clicks on the expander. I want to refine the model by adding a property public bool HasChildren { get { ... } } to my backing TreeNodeViewModel. Question: How can I bind this property to hide/show the expand icon (in XAML)? I am not able to find a suitable trigger/setter combination. (INotifyPropertyChanged is properly implemented.) Thanks for your time. Update 1: I want to use my property public bool HasChildren instead of using the dummy element. Determining whether or not an item has children is somewhat costly, but still much cheaper than fetching the children.

    Read the article

  • D3.js: "NS_ERROR_DOM_BAD_URI: Access to restricted URI denied"

    - by user2102328
    I have an html-file with several d3-graphs directly written in script tags into it. When I outsource one of the graphs into an external js file I get this message "NS_ERROR_DOM_BAD_URI: Access to restricted URI denied". If I delete the code with d3.json where it reads a local json file the error disappears. But it has to be possible to load a json file in an external js which is embedded into an html, right? d3.json("forcetree.json", function(json) { root = json; update(); });

    Read the article

  • HTML to XAML Conversion, Display HTML in RichTextBox

    - by Erika
    Hi, unfortunately im REALLY stuck on this and was wondering in anyone knows how to work around this. I have some html text which i want displayed in a WPF RichTextBox. At the moment, i'm using some helper APIs found http://blogs.msdn.com/wpfsdk/archive/2006/05/25/606317.aspx to convert HTML to XAML. So at the moment i have a xaml data string, but i cant see to find a way to display this correctly within the richtextbox :s i have been trying the following: string xamlData = HTMLConverter.HtmlToXamlConverter.ConvertHtmlToXaml(sBody,true); FlowDocument result = XamlReader.Load(new System.Xml.XmlTextReader(new StringReader(xamlData))) as FlowDocument; but this is crashing on the XamlReader.. Any other way will do, i just need to display an HTML string in this RichTextBox or something else! Please Help!

    Read the article

  • How to play youtube videos which using Youtube.apk for android 2.1 platform

    - by danny
    I have a problem, I have a Youtube.apk that version is 1.5.20, so I would like to play Youtube videos in android 2.1 platform, but some problems: ======================================================================================= I/ActivityManager( 52): Starting activity: Intent { act=android.intent.action.MAIN cat=[android.intent.category.LAUNCHER] flg=0x10200000 cmp=com.google.android.youtube/.HomeA} I/ActivityManager( 52): Start proc com.google.android.youtube for activity com.google.android.youtube/.HomeActivity: pid=373 uid=10021 gids={3003} D/installd( 36): DexInv: --- BEGIN '/system/app/YouTube.apk' --- D/dalvikvm( 379): DexOpt: load 106ms, verify 597ms, opt 24ms D/installd( 36): DexInv: --- END '/system/app/YouTube.apk' (success) --- I/ActivityThread( 373): Publishing provider com.google.android.youtube.SuggestionProvider: com.google.android.youtube.suggest.SuggestionProvider I/YouTube ( 373): Distribution channel:mvapp-android-mid120 D/ ( 373): unable to unlink '/data/data/com.google.android.youtube/shared_prefs/youtube.xml.bak': No such file or directory (errno=2) I/AndroidRuntime( 373): AndroidRuntime onExit calling exit(-42) I/ActivityManager( 52): Process com.google.android.youtube (pid 373) has died. D/Zygote ( 33): Process 373 exited cleanly (214) I/UsageStats( 52): Unexpected resume of com.android.launcher while already resumed in com.google.android.youtube W/WindowManager( 52): Rebuild removed 2 windows but added 1 W/InputManagerService( 52): Window already focused, ignoring focus gain of: com.android.internal.view.IInputMethodClient$Stub$Proxy@4406d498 ============================================================================================= so, How to fix this problem thanks~

    Read the article

  • "An internal error occurred." when loading pfx file with X509Certificate2

    - by tmp3128
    I'm trying use self-signed certificate (c#): X509Certificate2 cert = new X509Certificate2(Server.MapPath("~/App_Data/myhost.pfx"), "pass"); on a shared web hosting server and I got an error: System.Security.Cryptography.CryptographicException: An internal error occurred. stack trace ends with System.Security.Cryptography.CryptographicException.ThrowCryptogaphicException(Int32 hr) +33 System.Security.Cryptography.X509Certificates.X509Utils._LoadCertFromFile(String fileName, IntPtr password, UInt32 dwFlags, Boolean persistKeySet, SafeCertContextHandle& pCertCtx) +0 System.Security.Cryptography.X509Certificates.X509Certificate.LoadCertificateFromFile(String fileName, Object password, X509KeyStorageFlags keyStorageFlags) +237 System.Security.Cryptography.X509Certificates.X509Certificate2..ctor(String fileName, String password) +131 On my dev machine it loads ok. The reason I load *.pfx not a *.cer file because I need a private key access (cer file loads Ok). I made pfx on my dev mochine like that: makecert -r -n "CN=myhost.com, [email protected]" -sky exchange -b 01/01/2009 -pe -sv myhost.pvk myhost.cer pvk2pfx -pvk myhost.pvk -spc myhost.cer -pfx myhost.pfx -po pass Please assist; PS: makecert is a v5.131.3790.0

    Read the article

  • dtexec with password

    - by user1602996
    I have added a new step in my job activity monitor which runs ssis package(encrepted with password). dtexec /f "\\sw-conf-dev-01\projects\dtsx\Email.dtsx" /de "ssispassword" error message: Description: The package is encrypted with a password. The password was not specified, or is not correct. End Error Could not load package "\sw-conf-dev-01\projects\dtsx\Email.dtsx" because of error 0xC0014037. Description: Failed to remove package protection with error 0xC0014037 "The package is encrypted with a password. The password was not specified, or is not correct.". This occurs in the CPackage::LoadFromXML method I have used the same password in the package as well, but i don't know why I'm still getting an error message. Any ideas?

    Read the article

< Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493  | Next Page >