Search Results

Search found 15209 results on 609 pages for 'configuration'.

Page 487/609 | < Previous Page | 483 484 485 486 487 488 489 490 491 492 493 494  | Next Page >

• openvpn problem

  - by Jared Voronik

  I have a problem with openvpn. I have already setup openvpn sucessfully on some other servers in the past (basic configuration, nothing special). On this server, I used the same config file, but for setting up nat iptables -t nat -A POSTROUTING -s 10.4.0.0/24 -o eth0 -j MASQUERADE doesn't work. It gives error: iptables v1.3.5: can't initialize iptables table `nat': Table does not exist (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. How do I fix this error? Also, if I can't fix this error, can I do bridging instead of routing? I have only 1 interface, and I can connect to remote server only via ssh (and need to avoid reboots if at all possible) so if briding means a whole ethernet card has to be devoted to the openvpn (and no other servers) then briding is out, otherwise I can use briding. Do you know of a simple, step by step guide to configure openvpn briding (just simple openvpn server and clients that can access internet through vpn server, nothing fancy)?

  Read the article

• I've just set up FreeBSD 8.0 and can't login with ssh

  - by Matt

  /etc/hosts.allow is set to allow any protocol from anywhere. I can "ssh localhost" and it works. I simply get "connection refused" from putty on another machine. Any ideas? Will try to get a copy of the sshd_server.conf file as soon as I can find a flash disk to copy it to, but I thought someone might know what you need to set initially to permit login. EDIT: I think I can see why it's not working now. If I telnet to the IP address of the server I'm seeing MGE UPS SYSTEMS SNMP Web/Agent configuration menu. Enter Password: Doh. Ok, so the IP address is assigned by DHCP, but it seems there is already a device statically assigned to that address. I'll put in a reservation and try again. ok, sorted now. It was an ip address conflict. Windows DHCP isn't smart enough to check if there is something listening on the address before first assigning it.

  Read the article

• Setting up port forwarding for web server

  - by Javier Badia

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• Google bots are severely affecting site performance

  - by Lynn

  I have an aggregate site on a linux server that pulls in feeds from a universe of about 2,000 blogs. It's in Wordpress 3.4.2 and I have a cron job that is staggered to run five times an hour on another server to pull in the stories and then publish them to the front page of this site. This is so I didn't put too much pressure all on one server. However, the Google bots, which visit a few times every hour bring the server to its knees in the morning and evenings when there is an increase in traffic on the site. The bots have something like 30,000 links to follow at this point. How do I throttle the bots to simply grab the new stories off the front page and stop there? EDIT- Details of my server configuration: The way we have this set up is the server that handles all the publishing is an unmanaged instance via AWS. It mounts the NFS server and connects to the RDS to update content, etc. You get to this publishing instance via a plugin that detects the wp-admin link and then redirects you into there. The front end app server also mounts the NFS and requests data from the RDS. It is the only one that has the WP Super Cache on it.... The OS is Ubuntu on the App server and the NFS runs CentOs. The front end is Nginx and the publishing server is Apache.

  Read the article

• Metacity/Compiz not staring upon Login Ubuntu 10.10

  - by Ryan Lanciaux

  TLDR: As of this afternoon, I do not have a window manager when I login to Ubuntu 10.10. I would like to have window manager on login without needing to add to startup. Just started using linux again as my home OS. (Used it for a long time years ago but been on windows up until this past weekend) so this may be kind of n00b-ish :) Anyways, up until today, everything on my machine was running okay. I did not have compiz running as the default wm because I'm running NVidia Drivers and Xinerama (and as I understand Xinerama & Compiz don't work well together). I made no changes to my xorg / etc but today when I logged in, I had to manually start metacity from command line to get any window manager. Really not sure what would be causing this or what I can do to get it working again. My xorg.conf is available here: https://gist.github.com/845618. My default Window Manager is set to /usr/bin/metacity in Configuration Editor under /desktop/gnome/applications/window_manager. p.s. Any tips on how to run 3 monitors where I can move windows between screens without Xinerama would be appreciated but that's prolly for another thread :)

  Read the article

• Ubuntu 12.04 open port 80 inside WLAN

  - by Eduard

  I have an nginx server running on ubuntu 12.04 that serves http through port 80 and https through port 443. Everything works fine if I access it from the same computer via localhost, 127.0.0.1 or the local IP 192.168.0.11. If I try to access the server from another computer in the same VLAN it does not work for http; it works for https. I have changed my nginx configuration to also listen to port 8000 for http; I can then access http from the other computer in the same VLAN via "http://192.168.0.11:8000". I also have a web server running on port 80 on a windows machine and can access it from another device in the same VLAN, therefore the router is not blocking incoming http traffic. The nginx process is run by root. I have used tcpdump and I see that packets are arriving to Ubuntu: 192.168.0.16.49735 192.168.0.11.80 and that some response is being given 192.168.0.11.80 192.168.0.16.49735 (I do not know what the response is though). There is no request arriving at the nginx web server (I have checked the access log). I have iptables empty. I have unsuccessfully tried to find a solution for a long time to this, it has now become a matter of happiness or bitterness :).

  Read the article

• Move OS from RAID5 array to RAID 1 arrays

  - by Antoine

  I want to give a last boost to my old ProLiant ML350 G5 server which just needs to be reliable for a few more year only ! With a defined budget of about 1500$ (I do not have more), i plan to replace the CPU (+ adding a second one), the battery cache of my raid controller (E200i), double the RAM, and change all hard drives. I have 7 HDD (SAS 10krpm, 72Gb) + 1 spare in RAID5, and my system is all FULL (no empty tray, full disks). in my current RAID5 array, I have 2 partitions: - 1 OS partition, 20Gb - 1 data partition, 350 Gb I plan to replace these 8 disks with : - 2 x 300Gb SAS 15krpm in RAID 1 (= 1 partition for OS) - 2 x 2Tb SATA 7.2krpm in RAID 1 (= 1 partition for DATA) My biggest constraint is that I have only 01 day to upgrade my server. Therefore, I'm looking for cloning all my files (OS + data partition) to my new arrays, i.e : - the OS partition shall be cloned to the RAID1 "2x300Gb array" - the data partition shall be cloned to the RAID1 "2x2Tb array" My second problem is that I need to physically remove all the old hard drives before inserting the new ones. I'm running Windows Server 2003 R2, and even if MS support will expire soon, I cannot buy a new licence and spent time in configuration. Obviously, with 1500$, I cannot also buy a new server that I could start configuring from now ! Thought about ASR (NTBackup), but I have no floppy drive (and do not really want to invest in one !) Thought about a clonezilla clone, and read this interesting link : Windows Server 2003 - move C: partition to a new SAS disk , but i'm not so confident in using Clonezilla with RAID5. What should be the best option to quickly and easily (if possible!) "copy/paste" my OS (so no need to reinstall and reconfigure all) and DATA / programs / services, etc... ? Thanks for your comments

  Read the article

• converting to MXF using ffmpeg

  - by Prakash

  I have been trying to use FFmpeg utility to convert a avi file using DNxHD to mxf format. I am using "FFmpeg" with params as following: ffmpeg -i ccvt_box.avi -vcodec dnxhd -video_size 1920x1080 -r 24 -b:v 115m ex.mxf The error it is giving : ffmpeg version N-43737-g76c3fff Copyright (c) 2000-2012 the FFmpeg developers built on Aug 20 2012 18:50:42 with llvm-gcc 4.2.1 (LLVM build 2336.11.00) configuration: libavutil 51. 70.100 / 51. 70.100 libavcodec 54. 53.100 / 54. 53.100 libavformat 54. 25.104 / 54. 25.104 libavdevice 54. 2.100 / 54. 2.100 libavfilter 3. 11.101 / 3. 11.101 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 15.100 / 0. 15.100 Input #0, avi, from 'ccvt_box.avi': Duration: 00:00:10.00, start: 0.000000, bitrate: 691 kb/s Stream #0:0: Video: indeo5 (IV50 / 0x30355649), yuv410p, 340x344, 10 tbr, 10 tbn, 10 tbc Metadata: title : bob.avi [dnxhd @ 0x7fcd60818e00] video parameters incompatible with DNxHD Output #0, mxf, to 'ex.mxf': Stream #0:0: Video: dnxhd, yuv422p, 340x344, q=2-1024, 90k tbn, 24 tbc Metadata: title : bob.avi Stream mapping: Stream #0:0 -> #0:0 (indeo5 -> dnxhd) Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height

  Read the article

• Slowdown upon router/modem setup change

  - by Ollie Saunders

  I’ve been using a Belkin FSD7632-4 modem router to connect to my TalkTalk provided ADSL internet connection for some time and been pretty happy with it. Recently, however, the connection has been failing and I decided to get a ASUS RT-N16 instead, which is also a much more capable router generally. The ASUS RT-N16 doesn’t come with a modem built-in so I purchased as Zoom modem as well. I’ve set them both up and am using them to post this message. But I’m a bit miffed to find that I get a significantly and consistently slower downstream rate from the new configuration than with the old Belkin. Belkin modem router: downstream: 3.45 mbps upstream: 0.73 mbps ASUS router + Zoom modem: downstream: 2.71 mbps upstream: 0.66 mbps Any ideas why this is? The really weird thing about this is that the Zoom supports ADSL2 and ADSL2+ but I don’t think the old Belkin does. At first I thought it might be due to the Zoom modem being limited to PPPoE instead of PPPoA, which my ISP supports, but then I tried using PPPoE with the Belkin and that still gave a high speed. I’m using VC-Mux encapsulation with both. VPI of 0 and VCI of 38. I pulled this data off the Zoom: Mode: ADSL2 Line Coding: Trellis On Status: No Defect Link Power State: L0 Downstream Upstream SNR Margin (dB): 12.3 11.8 Attenuation (dB): 43.0 24.9 Output Power (dBm): 12.9 0.0 Attainable Rate (Kbps): 3936 844 Rate (Kbps): 3194 840 MSGc (number of bytes in overhead channel message): 59 10 B (number of bytes in Mux Data Frame): 99 14 M (number of Mux Data Frames in FEC Data Frame): 2 16 T (Mux Data Frames over sync bytes): 1 8 R (number of check bytes in FEC Data Frame): 8 8 S (ratio of FEC over PMD Data Frame length): 1.9833 9.0594 L (number of bits in PMD Data Frame): 839 219 D (interleaver depth): 32 2 Delay (msec): 15 4 Super Frames: 15808 14078 Super Frame Errors: 0 4294967232 RS Words: 513778 111753 RS Correctable Errors: 126 4294967238 RS Uncorrectable Errors: 0 N/A HEC Errors: 0 4294967279 OCD Errors: 0 0 LCD Errors: 0 0 Total Cells: 1920175 237597 Data Cells: 205993 392 Bit Errors: 0 0 Total ES: 0 0 Total SES: 0 0 Total UAS: 34 0

  Read the article

• git : The remote end hung up unexpectedly - too many simultaneous users?

  - by Pritam Barhate

  I asked this first on StackOverflow and I was suggested that I should ask it here: We have a self hosted git server (Gitolite) on a VPS account (CPU:2.68GHz RAM:1824MB). This same VPS is also used to publish our underdevelopment web apps for client demos. (Very little traffic). so the main use of the server is as a Git Server Only. This git server is accessed by a team of 30-40 people for various projects. Our problem is that during the day when 6-7 people are trying to access the server (sometimes same repo) we get frequent error message: ssh: connect to host xxx.xxx.xx.xx port 22: Bad file number fatal: The remote end hung up unexpectedly After trying for 10-15 minutes it generally succeeds. During early mornings and late nights when there are only 1-2 people, git commands work with 100% success rate. Also I would like to note that if I access the other file hosted on the server through HTTP it works fine. I found a couple of questions on StackOverflow and on other sites regarding this. But most of the people point towards SSH key set up or conflicts between Msysgit and Cygns SSH. However I don't think this is the problem in our case as we get this behavior on Windows (using msysgit only) as well as Mac Machines. Also if it was SSH configuration issue then it shouldn't work at all. But in our case it works after 10-15 minutes. I think in our case it might be too many simultaneous connections to same server (or same repo) or something like that. Does there exists a setting or a conf file that needs to modified to solve this problem? Please help me solve this problem or point me in the right direction. Thanks in advance. Pritam.

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Nginx - Serve blank page on "Bad Gateway" error

  - by TheLittleCheeseburger

  Hello all. I want to use Nginx as a simple reverse proxy, but if the server behind Nginx is down I just was to display a blank page. For some reason this configuration isn't displaying a blank page on error 502 and I can't figure out why. Thanks for your help! user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; use epoll; # multi_accept on; } http { keepalive_timeout 65; proxy_read_timeout 200; upstream tornado { server 127.0.0.1:8001; } server { listen 80; server_name www.something.com; location / { error_page 502 = @blank; proxy_pass http://tornado; } location @blank { index index.html; root /web/blank; } } }

  Read the article

• windows 7 turns off itself everyday at about 9am

  - by Radek

  I was given this comp at work and after a week or so this strange thing started to happen in the middle of doing something :-( It turns off itself at about 9.10am every morning Just once a day and it works fine after it had it little nap. it happens both if the comp was on all night or I turned it off before leaving the office. I tried to swapped the memory as I was told that there was an issue with memory. But moving or removing any memory did not make any difference. I am not aware that I would install any program that could cause that. I installed AVG and set it up to do every day scan about 8am + if restart is needed it requires user confirmation. 'The Software Protection service has stopped' few minutes before it turned off itself but it happened also at other times without the computer turned off. I turned off Windows automatic updates as the first thing when I got the comp configuration Windows 7 Ultimate Intel Core2 Quad Q9550 at 2.8GH, 8GB RAM ST31000528AS Barracuda 7200.12 SATA 3Gb/s 1TB Update Below message are logged when I turn the comp on again. Message 1: The previous system shutdown at 9:08:54 AM on ?6/?29/?2010 was unexpected. Message 2: Level:Critical Source: Kernel Power EventID 41 Task Category (63) The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Log after manual restart Update 2 (task scheduler)

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Apache Server not working in MAMP

  - by jasonaburton

  Here's what I did before the problem started: I was creating a database for a site that I am working on in phpMyAdmin. I wrote some code to try to connect to the database I just created and I couldn't connect. I assumed it might be because I needed a password to connect to the database, so I created a password for it. Immediately after I created the password phpMyAdmin kicked me out saying: "#1045 - Access denied for user 'root'@'localhost' (using password: YES)" "phpMyAdmin tried to connect to the MySQL server, and the server rejected the connection. You should check the host, username and password in your configuration and make sure that they correspond to the information given by the administrator of the MySQL server." I found the php.ini file and searched for where I could change the password to match the one I just made, but couldn't find where I needed to change it. So I decided to scrap the database and uninstall MAMP from my computer and reinstall it hoping it would just reset all the defaults and I could go on my merry way. But now after reinstalling MAMP and trying to run the servers Apache won't start up and I have no idea why. One problem after another... Any advice or helpful ideas?

  Read the article

• samba access from win98

  - by SimonSalman

  Hello, the admin installed a new file server in our institute: OpenSuse 11.1 with Samba 3.2.7-11.3.2-2154-SUSE-CODE11. They copied the smb.conf from the old machine (hosting Samba 3.0.0) to the new one. Everything works as before, but one Windows 98 machine can see but not access the file server. It prompts for user authentication, but will not accept any user-password combination. There exists a lot of discussion about the problem on the net, but none provided a clear answer to the problem. EDIT: 1. I changed Win98 registry enable plain-text passwords, and alternatively changed server's smb.conf and /etc/smbpasswd to accept encrypted passwords 2. Further I provide a profile with a user-password combination on Win98 machine similar to one of the samba users-password combinations. 3. I changed smb.conf such that the samba server is the Local Master Browser all these changes are not necessary when using the older samba server. So, I conclude that a configuration problem on the server side is likely. If you need any further information, I will post them here. Best regards, Simon

  Read the article

• Poor performance on IIS7, only on Windows Server 2008, fine on Windows 7?

  - by user32005

  Hi, I'm new to IIS7 but have experience with other versions. I've been working on an application that works great in a dev environment (as always) but when I push it to a windows server 2008/IIS7 box performance takes a noticeable hit. The dev environment is Windows7/IIS7. The configuration in IIS is the same on the dev box as the server. I've tried all sorts of things to try and find a reason for this but I cant come to any conclusion. I've ruled out database problems on the live box as all data is cached after the first request. I've confirmed this to be true and made sure there is no additional database traffic. I've ruled out network issues with a combination of monitoring requests with fiddler and local debugging on the server. Whenever the code runs on the server there seems to be a performance issue. The server: Intel Core 2 Quad CPU Q6600 @ 2.40ghz with 2gb RAM. I know this is not fantastic but I was expecting it to at least perform as well as my dev environment (which is running much more on a lower spec). The CPU using peaks at under 60%, and memory usage is less than half of the available. I've enabled failed request tracing and most of the time is spent in a custom HttpModule, this module works to handle every request, I cant get any more detail as to what within the module may be causing the problem. Any ideas, I've been pulling my hair out for days now. Thanks

  Read the article

• Connect by Wifi to Sql Server from another computer

  - by Bronzato

  I try to connect by Wifi to Sql Server with Sql Server Management Studio from another computer but it failed. I have a computer with Windows Seven & Sql Server 2008 (lets say the server computer). Next to it, I have a fresh installed computer with Windows Seven & Sql Server Management Studio (let's say the client computer). What I do on the server computer: configure firewall by enabling port 1433 enabled network protocols (TCP/IP) inside Sql Server Configuration Manager checked "Allow remote connections to this server" on server properties in Sql Server Management. started Sql Server Browser restarted services (Sql Server Browser is stopped but I think it is not neccessary, isn't it?) Next, I successfully tested a ping on the port 1433 from my client computer with a tool named tcping (ex: tcping 192.168.1.4 1433). But I still cannot connect from my client computer to Sql Server on my other computer. Ok, something new on this problem: until now, I successfully connected to my "server computer" with Management Studio. What I do is typing the computer name in the server name field in the connection window of Management Studio. My previous (failed) attempt was to type the computer name followed by the instance of sql server (ex: COMPUTER_NAME\SQL2008). I don't know why I only have to type the computer name... Nevermind. Now my new challenge is to succeed connecting my VB6 application to this remote database located on my "computer server". I have a connection string for this but it failed to connect. Here is my connection string: "Provider=SQLOLEDB.1;Password=mypassword;User ID=sa;Initial Catalog=TPB;Data Source=THIERRY-HP\SQL2008" Any idea what's wrong? Thanks

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Deploy our own software using Puppet?

  - by Ken

  (Apologies in advance for the stupidity in this question. I'm normally a programmer, not a sysadmin, but I've taken it upon myself to automate some things, and clean up some other things which are automated but not in the prettiest way. :-) I've been looking around at various tools for automation of software deployment to a bunch of servers, like cfengine, Puppet, and Chef. So far, Puppet looks the most appealing, but I've certainly not committed to anything yet. These tools all look like they can do a great job of keeping a bunch of servers up-to-date with prepackaged software. What I don't get is: how does one use a tool (like Puppet) to manage deployments of our own internal software? I think I'm at a loss because I've seen a thousand tutorials showing how to keep Apache ensure => latest (which is pretty cool), but nothing that quite corresponds to my use-case today, which is something more like: when a human being pushes The Button, pull branch A from the version-control repository B run command C to compile it copy the binaries D to servers E1 through E10 on each server, run command F to make all changes take effect Puppet sounds great, and I totally see the advantage of declarative, idempotent configuration over some shell scripts, but I've not seen any tutorials for "you want to update your shell scripts to Puppet (or Chef, or cfengine) so here's what you should do". Is there such a thing? Is it obvious to other people how to take the things provided in the Puppet docs and replicate the behavior I want? Am I just not getting it? What it's sounding like to me, so far, is that the human being (#1) would manually package the software (#2 and #3) external to Puppet, manually update the Puppet config, which would trigger Puppet to update the servers ... maybe? (I'm a little confused here, as I'm sure you can tell.) Thanks!

  Read the article

• Suddenly can't send E-Mails with Apple Mail to Gmail SMTP

  - by slhck

  Hi all, I have a weird problem that started just today. I am using Apple Mail on a Leopard machine, connecting to Gmail. Fetching e-mail works just fine. My SMTP settings are also correct. Still, I can't send mail, it will display a pop up saying that "transferring the content to the mail server" failed (translation from German, could be different in English OS X versions). I have verified the following: My SMTP settings are definitely correct. I have not changed them and the issue appeared today. Also, I went through the Apple online configuration for Gmail accounts and did not have to adjust any setting. I can run network diagnosis and it will connect to both POP and SMTP servers without a problem (all green lights) The Telnet details will show me the HELO message from the Gmail servers, so there's no authentication failure. Console.app will not show any messages related to "mail" when I try to send the mail, so there's no specific error message The mail I'm trying to send does not have an attachment, it is plaintext only I can login to gmail.com and send mails without a problem The recipient address exists and contains no syntax errors I can also not send mails to myself When using another IP and ISP (through VPN), it still doesn't work As for my settings: I connect to smtp.gmail.com and for advanced settings I choose password-based authentication with user: [email protected] and my password. I let Apple Mail try the default ports (for SSL and TLS, respectively). Again: I have not changed a thing between yesterday and today. What is causing that strange behavior? Any help would be much appreciated.

  Read the article

• Ubuntu server crashes; need help figuring how to figure out why

  - by neezer

  I have a 768 Slice at slicehost.com running Ubuntu Server 8.04.2 LTS (hardy) with a LAMP stack on it that periodically crashes, though why I am not sure. From what I can tell, there is a process that basically goes rogue and consumes all the memory on the slice, suffocating all the other programs running until the whole thing comes to a grinding halt, and I have to do a hard reboot of the slice to get it back up and running again. I can't detect any pattern for this (it seems to happen about once a month, more or less). Here's a screenshot of my console during the last crash: I would assume that a possible cause might a PHP script or an apache configuration rule that might cause the crash if triggered? How would I be able to find out which one is the offending one? I've checked and rechecked all my PHP scripts, and running them doesn't seem to trigger the crash. I've also been able to log on to my system during a crash and see what's running (with top), but I can't tell how the offending process was started, so I can't trace the root of the problem! I know my description is overly generic, but unfortunately my expertise in tracking down the source of these glitches is very limited. If you need any additional information about my system in order to help me figure this out, please let me know in the comments, and I will append it to the question. My only other lead as to the culprit here is Wordpress, which we have installed on this server. Here are the details: Wordpress 3.0.3 with the following plugins installed and activated: Addmarx - Bookmark/Share/Email Dropdown, Akismet, All in One SEO Pack, Animated Banners, Automatically publish highlights of any website, directly to your Blog, Broken Link Checker, CMS Dashboard, Collapsing Categories, Status Updater, SubHeading, Ultimate Google Analytics, VastSubCat, WP-CMS Post Control, and WP Super Cache

  Read the article

• Courier-imap login problem after upgrading / enabling verbose logging

  - by halka

  I've updated my mail server last night, from Debian etch to lenny. So far I've encountered a problem with my postfix installation, mainly that I managed to broke the IMAP access somehow. When trying to connect to the IMAP server with Thunderbird, all I get in mail.log is: Feb 12 11:57:16 mail imapd-ssl: Connection, ip=[::ffff:10.100.200.65] Feb 12 11:57:16 mail imapd-ssl: LOGIN: ip=[::ffff:10.100.200.65], command=AUTHENTICATE Feb 12 11:57:16 mail authdaemond: received auth request, service=imap, authtype=login Feb 12 11:57:16 mail authdaemond: authmysql: trying this module Feb 12 11:57:16 mail authdaemond: SQL query: SELECT username, password, "", '105', '105', '/var/virtual', maildir, "", name, "" FROM mailbox WHERE username = '[email protected]' AND (active=1) Feb 12 11:57:16 mail authdaemond: password matches successfully Feb 12 11:57:16 mail authdaemond: authmysql: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> Feb 12 11:57:16 mail authdaemond: Authenticated: sysusername=<null>, sysuserid=105, sysgroupid=105, homedir=/var/virtual, [email protected], fullname=<null>, maildir=xoxo.sk/[email protected]/, quota=<null>, options=<null> ...and then Thunderbird proceeds to complain that it cant' login / lost connection. Thunderbird is definitely not configured to connect through SSL/TLS. POP3 (also provided by Courier) is working fine. I've been mainly looking for a way to make the courier-imap logging more verbose, like can be seen for example here. Edit: Sorry about the mess, I've found that I've been funneling the log through grep imap, which naturally didn't display entries for authdaemond. The verbose logging configuration entry is found in /etc/courier/imapd under DEBUG_LOGIN=1 (set to 1 to enable verbose logging, set to 2 to enable dumping plaintext passwords to logfile. Careful.)

  Read the article

• How can I update generic non-pnp monitor?

  - by njk

  Background I've been running a KVM switch with my monitor at 1920 x 1080 over VGA for over a year. Did a Windows Update on 12/11/12 which did the following: Update for Windows 7 for x64-based Systems (KB2779562) Security Update for Windows 7 for x64-based Systems (KB2779030) Cumulative Security Update for Internet Explorer 8 for Windows 7 for x64-based Systems (KB2761465) Windows Malicious Software Removal Tool x64 - December 2012 (KB890830) Security Update for Windows 7 for x64-based Systems (KB2753842) Security Update for Windows 7 for x64-based Systems (KB2758857) Security Update for Windows 7 for x64-based Systems (KB2770660) After a restart, my extended monitor was dark. I attempted to reset the extended display configuration, and noticed my monitor was being detected as a Generic Non-PnP Monitor: I uninstalled, downloaded new, and re-installed display drivers. Nothing. I attempted to unplug my monitor from the power for 15 minutes. Nothing. I followed some of the suggestions on this thread; specifically DanM's which suggested to create a new *.inf file and replace that in Device Manager. Device Manager said the "best driver software for your device is already installed". The only thing that works is when the monitor is directly attached to the laptop. This obviously is not what I want. My thought is to somehow remove the Generic Non-PnP Monitor from registry. How would I accomplish this and would this help? Any other suggestions? Relevant Hardware ASUS VE276 Monitor TRENDnet 2-Port USB KVM Switch (TK-207K) HP Laptop w/ ATI Radeon HD 4200 Screens

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

< Previous Page | 483 484 485 486 487 488 489 490 491 492 493 494  | Next Page >