Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 487/627 | < Previous Page | 483 484 485 486 487 488 489 490 491 492 493 494  | Next Page >

• Issue with multiple bridging for KVM hosts

  - by Henry-Nicolas Tourneur

  I'm using KVM and libvirt on my host (Debian lenny) + 2 bridges per guest (one for mgmt, one for public traffic). That setup isn't stable at all, sometimes I can do pings to a management ip, sometimes not. I don't know if my bridging paramateres are correct, could you check ? or if there is anything wrong ... Please also note that interface on guest doesn't flap and that I got not logs on my host. Of course forwarding is enabled. iface eth3 inet manual auto bond0 iface bond0 inet manual slaves eth1 eth2 pre-up ip link set bond0 up down ip link set bond0 down auto br0 iface br0 inet static address 10.160.0.7 netmask 255.255.255.128 bridge_ports eth3 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br0:1 iface br0:1 inet static address 10.160.0.9 netmask 255.255.255.128 auto br0:2 iface br0:2 inet static address 10.160.0.10 netmask 255.255.255.128 auto br1 iface br1 inet static address 217.4.40.242 netmask 255.255.255.240 gateway 217.4.40.241 pre-up /etc/network/firewall start bridge_ports bond0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off auto br1:1 iface br1:1 inet static address 217.4.40.252 netmask 255.255.255.240 auto br1:2 iface br1:2 inet static address 217.4.40.253 netmask 255.255.255.240

  Read the article

• New SSD, is the MBR broken? DISK BOOT FAILURE

  - by Shevek

  I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

  Read the article

• VNC from Windows to OS X Lion: App stuck in fullscreen mode

  - by Jonny

  I'm connecting to a remote Mac through a Windows. ahh it gets more complicated than that. I'm sitting by my iMac. I use Virtual Box in it to launch Windows 7. In it I have a VPN connection to a remote Windows network, which allows me to use Remote Desktop to one of the Windows (Vista!) boxes over there. From that Vista box I VNC into a Mac OS X Lion. (Don't ask me why, but that Mac doesn't have a public ip which prevents me from accessing it in the first place.) So: OSXLion - (virtual)Windows7 - Windows Vista - OSX Lion That last Mac was recently upgraded from Snow Leopard. Now with Lion, sometimes apps run in fullscreen. Somehow I can't get out of that fullscreen. Normally you'd move the mouse pointer to the top of screen and a menu list bar drops down allowing you to reach the fullscreen button top right. Now, in my current setup that menu list bar never drops down on the remote Mac at the end of the line. Any ideas?

  Read the article

• How do I Install Intermediate Certificates (in AWS)?

  - by getmizanur

  I have installed private key (pem encoded) and public key certificate (pem encoded) on Amazon Load Balancer. However, when I check the SSL with site test tool, I get the following error: Error while checking the SSL Certificate!! Unable to get the local issuer of the certificate. The issuer of a locally looked up certificate could not be found. Normally this indicates that not all intermediate certificates are installed on the server. I converted crt file to pem using these commands from this tutorial: openssl x509 -in input.crt -out input.der -outform DER openssl x509 -in input.der -inform DER -out output.pem -outform PEM During setup of Amazon Load Balancer, the only option I left out was certificate chain. (pem encoded) However, this was optional. Could this be cause of my issue? And if so; How do I create certificate chain? UPDATE If you make request to VeriSign they will give you a certificate chain. This chain includes public crt, intermediate crt and root crt. Make sure to remove the public crt from your certificate chain (which is the top most certificate) before adding it to your certification chain box of your Amazon Load Balancer. If you are making HTTPS requests from an Android app, then above instruction may not work for older Android OS such as 2.1 and 2.2. To make it work on older Android OS: go here click on "retail ssl" tab and then click on "secure site" "CA Bundle for Apache Server" copy and past these intermediate certs into certificate chain box. just incase if you have not found it here is the direct link. If you are using geo trust certificates then the solution is much the same for Android devices, however, you need to copy and paste their intermediate certs for Android.

  Read the article

• Extremely high mysqld CPU usage with no active queries

  - by RadarNyan

  I have a VPS running Ubuntu 12.04 LTS with LEMP stack, followed the guide from Linode Library (since I'm using a Linode) to setup, and everything worked fine until now. I don't know what's wrong, but my CPU usage just goes up since a week ago. Today things getting really bad - I got 74% CPU usage so I went check and found that mysqld taking too much CPU usage (somewhere around 30% ~ 80%) So I did some Google Search, tried disable InnoDB, restart mysql, reset ntp / system clock (Isn't this bug supposed to happen more than a year ago?!) and reboot my VPS, nothing helped. Even with mysql processlist empty, I still get mysqld CPU usage very high. I don't know what I missed and have totally no idea, any advice would be appreciated. Thanks in advance. Update: I got these from running "strace mysqld" write(2, "InnoDB: Unable to lock ./ibdata1"..., 44) = 44 write(2, "InnoDB: Check that you do not al"..., 115) = 115 select(0, NULL, NULL, NULL, {1, 0}^[[A^[[A) = 0 (Timeout) fcntl64(3, F_SETLK64, {type=F_WRLCK, whence=SEEK_SET, start=0, len=0}, 0xbfa496f8) = -1 EAGAIN (Resource temporarily unavailable) hum... I did tried to disable InnoDB and it didn't fix this problem. Any idea? Update2: # ps -e | grep mysqld 13099 ? 00:00:20 mysqld then use "strace -p 13099", the following lines appears repeatedly: fcntl64(12, F_GETFL) = 0x2 (flags O_RDWR) fcntl64(12, F_SETFL, O_RDWR|O_NONBLOCK) = 0 accept(12, {sa_family=AF_FILE, NULL}, [2]) = 14 fcntl64(12, F_SETFL, O_RDWR) = 0 getsockname(14, {sa_family=AF_FILE, path="/var/run/mysqld/mysqld.sock"}, [30]) = 0 fcntl64(14, F_SETFL, O_RDONLY) = 0 fcntl64(14, F_GETFL) = 0x2 (flags O_RDWR) setsockopt(14, SOL_SOCKET, SO_RCVTIMEO, "\36\0\0\0\0\0\0\0", 8) = 0 setsockopt(14, SOL_SOCKET, SO_SNDTIMEO, "<\0\0\0\0\0\0\0", 8) = 0 fcntl64(14, F_SETFL, O_RDWR|O_NONBLOCK) = 0 setsockopt(14, SOL_IP, IP_TOS, [8], 4) = -1 EOPNOTSUPP (Operation not supported) futex(0xb786a584, FUTEX_WAKE_OP_PRIVATE, 1, 1, 0xb786a580, {FUTEX_OP_SET, 0, FUTEX_OP_CMP_GT, 1}) = 1 futex(0xb7869998, FUTEX_WAKE_PRIVATE, 1) = 1 poll([{fd=10, events=POLLIN}, {fd=12, events=POLLIN}], 2, -1) = 1 ([{fd=12, revents=POLLIN}]) er... now I totally don't get it x_x help

  Read the article

• Using gitlab behind Apache proxy all generated urls are wrong

  - by Hippyjim

  I've set up Gitlab on Ubuntu 12.04 using the default package from https://about.gitlab.com/downloads/ {edit to clarify} I've set up Apache to proxy and run the nginx server the package installed on port 8888 (or so I thought). As I had Apache installed already I have to run nginx on localhost:8888. The problem is, all images (such as avatars) are now served from http://localhost:8888, and all the checkout urls Gitlab gives are also localhost - instead of using my domain name. If I change /etc/gitlab/gitlab.rb to use that url, then Gitlab stops working and gives a 503. Any ideas how I can tell Gitlab what URL to present to the world, even though it's really running on localhost? /etc/gitlab/gitlab.rb looks like: # Change the external_url to the address your users will type in their browser external_url 'http://my.local.domain' redis['port'] = 6379 postgresql['port'] = 2345 unicorn['port'] = 3456 and /opt/gitlab/embedded/conf/nginx.conf looks like: server { listen localhost:8888; server_name my.local.domain; [Update] It looks like nginx is still listening on the wrong port if I don't specify localhost:8888 as the external_url. I found this in /var/log/gitlab/nginx/error.log 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: bind() to 0.0.0.0:80 failed (98: Address already in use) 2014/08/19 14:29:58 [emerg] 2526#0: still could not bind() Apache setup looks like: <VirtualHost *:80> ServerName my.local.domain ServerSignature Off ProxyPreserveHost On AllowEncodedSlashes NoDecode <Location /> ProxyPass http://localhost:8888/ ProxyPassReverse http://127.0.0.1:8888 ProxyPassReverse http://my.local.domain </Location> </VirtualHost> Which seems to proxy everything back ok if Gitlab listens on localhost:8888 - I just need Gitlab to start displaying the right URL, instead of localhost:8888.

  Read the article

• Configuring ZenOSS to monitor CPU load

  - by Tom

  I'm trying test out monitoring tools for a network at work with a coworker but neither of us have ever used an sort of monitoring tools before. Currently we are experimenting with ZenOSS and having some difficulties. We want to populate our CPU load graphs because that is one of the primary feature we are looking for in our monitoring tools but we have been unable to populate the graphs with data. So far we have installed the wmipreformance, sqldatasource, wmidatasource, snmpperformance(simple) zenpacks and the machine we are trying to monitor is running Windows XP. We have tried to model the device and everything seems to run and we've tride to add data points to graphs but the only options we recieve for graphs are CPU and Memory. We are able to monitor services, ZenOSS recognizes the make and model of the processor, RAM, and Harddrive and is even giving us metrics on available storage but again, we are looking for performance metrics such as CPU load and Memory utilization. I realize I probably didn't provide a lot of information but that is because we don't have a very good idea of what we are doing and can't find instruction either on the ZenOSS homepage or forums to monitor CPU load. If someone could give us step by step instruction on how to set up CPU load monitoring that would probably be more beneficial to us than a diagnostic of our current setup, but regardless, if I left any important information out and you need it to answer the question, please let me know. Thank you.

  Read the article

• chrooted sftp user with write permissions to /var/www

  - by matthew

  I am getting confused about this setup that I am trying to deploy. I hope someone of you folks can lend me a hand: much much appreciated. Background info Server is Debian 6.0, ext3, with Apache2/SSL and Nginx at the front as reverse proxy. I need to provide sftp access to the Apache root directory (/var/www), making sure that the sftp user is chrooted to that path with RWX permissions. All this without modifying any default permission in /var/www. drwxr-xr-x 9 root root 4096 Nov 4 22:46 www Inside /var/www -rw-r----- 1 www-data www-data 177 Mar 11 2012 file1 drwxr-x--- 6 www-data www-data 4096 Sep 10 2012 dir1 drwxr-xr-x 7 www-data www-data 4096 Sep 28 2012 dir2 -rw------- 1 root root 19 Apr 6 2012 file2 -rw------- 1 root root 3548528 Sep 28 2012 file3 drwxr-x--- 6 www-data www-data 4096 Aug 22 00:11 dir3 drwxr-x--- 5 www-data www-data 4096 Jul 15 2012 dir4 drwxr-x--- 2 www-data www-data 536576 Nov 24 2012 dir5 drwxr-x--- 2 www-data www-data 4096 Nov 5 00:00 dir6 drwxr-x--- 2 www-data www-data 4096 Nov 4 13:24 dir7 What I have tried created a new group secureftp created a new sftp user, joined to secureftp and www-data groups also with nologin shell. Homedir is / edited sshd_config with Subsystem sftp internal-sftp AllowTcpForwarding no Match Group <secureftp> ChrootDirectory /var/www ForceCommand internal-sftp I can login with the sftp user, list files but no write action is allowed. Sftp user is in the www-data group but permissions in /var/www are read/read+x for the group bit so... It doesn't work. I've also tried with ACL, but as I apply ACL RWX permissions for the sftp user to /var/www (dirs and files recursively), it will change the unix permissions as well which is what I don't want. What can I do here? I was thinking I could enable the user www-data to login as sftp, so that it'll be able to modify files/dirs that www-data owns in /var/www. But for some reason I think this would be a stupid move securitywise.

  Read the article

• Can a folder on a NAS be made available as a physical drive in VMWare?

  - by asbjornu

  We are currently in the process of moving from a single web server to two load balanced web servers and are facing some challenges we don't quite know how to fix. One of these is that the current single server hosts applications that write stuff to disk. The applications running on the server expects that when something is written to disk it later will in fact exist, so it's important that this premise is fulfilled with the dual server architecture as well. The dual server setup is a couple of VMWare instances with Windows Server 2008 R2 as the guest operating system. Out of the box, these instances does not share any kind of file system, so just moving the applications over would make them break since one instance would write something to the file system that doesn't exist on the other. Thus we need to share a file system between the two virtual servers. Our host has proposed to create a network share on a SAN and map this share individually on each virtual machine. This doesn't work too well due to NTFS permissions, etc., because the share needs to be accessed by several independent web applications that won't even be in the same application pool. The only solution that kind of works is to hard code an "identity" for each web application into its web.config file, but this means password in clear text which doesn't sit well with me. Since the servers are virtual, I'm thinknig: Wouldn't it be possible to make a NAS area available as a physical disk in the gues operating system somehow? Since VMWare has full control of the virtual hardware, you'd think it would be able to "fake" a local hard drive in the virtual machine that in reality is a folder on a NAS, but so far I haven't found anything that states how and if this is possible. So I have to ask the wonderful Server Fault community: Can a folder on a NAS be made available as a physical drive (typical D:) in both of the virtual machines?

  Read the article

• Python module: Trouble Installing Bitarray 0.8.0 on Mac OSX 10.7.4

  - by Gabriele

  I'm new here! I have trouble installing bitarray (vers 0.8.0) on my Mac OSX 10.7.4. Thanks! ('gcc' does not seem to be the problem) Last login: Sun Sep 9 22:24:25 on ttys000 host-001:~ gabriele$ gcc -version i686-apple-darwin11-llvm-gcc-4.2: no input files host-001:~ gabriele$ Last login: Sun Sep 9 22:18:41 on ttys000 host-001:~ gabriele$ cd /Library/Frameworks/Python.framework/Versions/2.7/lib/python2.7/site-packages/bitarray-0.8.0/ host-001:bitarray-0.8.0 gabriele$ python2.7 setup.py installrunning install running bdist_egg running egg_info creating bitarray.egg-info writing bitarray.egg-info/PKG-INFO writing top-level names to bitarray.egg-info/top_level.txt writing dependency_links to bitarray.egg-info/dependency_links.txt writing manifest file 'bitarray.egg-info/SOURCES.txt' reading manifest file 'bitarray.egg-info/SOURCES.txt' writing manifest file 'bitarray.egg-info/SOURCES.txt' installing library code to build/bdist.macosx-10.6-intel/egg running install_lib running build_py creating build creating build/lib.macosx-10.6-intel-2.7 creating build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/__init__.py -> build/lib.macosx-10.6-intel-2.7/bitarray copying bitarray/test_bitarray.py -> build/lib.macosx-10.6-intel-2.7/bitarray running build_ext building 'bitarray._bitarray' extension creating build/temp.macosx-10.6-intel-2.7 creating build/temp.macosx-10.6-intel-2.7/bitarray gcc-4.2 -fno-strict-aliasing -fno-common -dynamic -isysroot /Developer/SDKs/MacOSX10.6.sdk -arch i386 -arch x86_64 -g -O2 -DNDEBUG -g -O3 -I/Library/Frameworks/Python.framework/Versions/2.7/include/python2.7 -c bitarray/_bitarray.c -o build/temp.macosx-10.6-intel-2.7/bitarray/_bitarray.o unable to execute gcc-4.2: No such file or directory error: command 'gcc-4.2' failed with exit status 1 host-001:bitarray-0.8.0 gabriele$

  Read the article

• Compiling linux kernel, how much size is needed?

  - by ant2009

  Hello, I am have downloaded the newest most stable linux kernel 2.6.33.2 I thought I would test this using virtualbox. So I create a dynamically sized harddisk of 4gb. And installed CentOS 5.3 with just the minimum packages. I setup the make menuconfig with just the default settings. After that I ran make and got the following error: net/bluetooth/hci_sysfs.o: final close failed: No space left on device make[2]: *** [net/bluetooth/hci_sysfs.o] Error 1 make[1]: *** [net/bluetooth] Error 2 make: *** [net] Error 2 The amount of space I have left is: # df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/VolGroup00-LogVol00 3.3G 3.3G 0 100% / /dev/hda1 99M 12M 82M 13% /boot tmpfs 125M 0 125M 0% /dev/shm My virtual size is 4gb, but the actual size is 3.5gb $ ls -hl total 7.5G -rw-------. 1 root root 3.5G 2010-04-13 14:08 LFS.vdi How much size should I give when compiling and installing a linux kernel? Is there any guidelines to follow when doing this? This is my first time, so just experimenting with this. Many thanks,

  Read the article

• rsnapshot - not correctly archiving mysql databases

  - by Tiffany Walker

  My rsnapshot configuration: snapshot_root /.snapshots/ backup /home/user localhost/ backup_script /usr/local/backup_mysql.sh localhost/mysql/ Using this file: NOW=$(date +"%m-%d-%Y") # mm-dd-yyyy format FILE="" # used in a loop ### Server Setup ### #* MySQL login user name *# MUSER="root" #* MySQL login PASSWORD name *# MPASS="YOUR-PASSWORD" #* MySQL login HOST name *# MHOST="127.0.0.1" #* MySQL binaries *# MYSQL="$(which mysql)" MYSQLDUMP="$(which mysqldump)" GZIP="$(which gzip)" # get all database listing DBS="$($MYSQL -u $MUSER -h $MHOST -p$MPASS -Bse 'show databases')" # start to dump database one by one for db in $DBS do FILE=$BAK/mysql-$db.$NOW-$(date +"%T").gz # gzip compression for each backup file $MYSQLDUMP --single-transaction -u $MUSER -h $MHOST -p$MPASS $db | $GZIP -9 > $FILE done It dumps the databases under / I then tried with the following: http://bash.cyberciti.biz/backup/rsnapshot-remote-mysql-backup-shell-script/ I got: rsnapshot hourly ---------------------------------------------------------------------------- rsnapshot encountered an error! The program was invoked with these options: /usr/bin/rsnapshot hourly ---------------------------------------------------------------------------- ERROR: backup_script /usr/local/backup_mysql.sh returned 1 WARNING: Rolling back "localhost/mysql/" ls -la /.snapshots/hourly.0/localhost/mysql total 8 drwxr-xr-x 2 root root 4096 Nov 23 17:43 ./ drwxr-xr-x 4 root root 4096 Nov 23 18:20 ../ What exactly am I doing wrong? EDIT: # /usr/local/backup_mysql.sh *** Dumping MySQL Database *** Database> information_schema..cphulkd..eximstats..horde..leechprotect..logaholicDB_ns1..modsec..mysql..performance_schema..roundcube..test.. *** Backup done [ files wrote to /.snapshots/tmp/mysql] *** root@ns1 [~]# ls -la /.snapshots/tmp/mysql total 8040 drwxr-xr-x 2 root root 4096 Nov 23 18:41 ./ drwxr-xr-x 3 root root 4096 Nov 23 18:41 ../ -rw-r--r-- 1 root root 1409 Nov 23 18:41 cphulkd.18_41_45pm.gz -rw-r--r-- 1 root root 113522 Nov 23 18:41 eximstats.18_41_45pm.gz -rw-r--r-- 1 root root 4583 Nov 23 18:41 horde.18_41_45pm.gz -rw-r--r-- 1 root root 71757 Nov 23 18:41 information_schema.18_41_45pm.gz -rw-r--r-- 1 root root 692 Nov 23 18:41 leechprotect.18_41_45pm.gz -rw-r--r-- 1 root root 2603 Nov 23 18:41 logaholicDB_ns1.18_41_45pm.gz -rw-r--r-- 1 root root 745 Nov 23 18:41 modsec.18_41_45pm.gz -rw-r--r-- 1 root root 138928 Nov 23 18:41 mysql.18_41_45pm.gz -rw-r--r-- 1 root root 1831 Nov 23 18:41 performance_schema.18_41_45pm.gz -rw-r--r-- 1 root root 3610 Nov 23 18:41 roundcube.18_41_45pm.gz -rw-r--r-- 1 root root 436 Nov 23 18:41 test.18_41_47pm.gz MySQL Backup seems fine.

  Read the article

• fail2ban regex working but no action being taken

  - by fpghost

  I have the following snippet of fail2ban configuration on Ubuntu 13.10 server: #jail.conf [apache-getphp] enabled = true port = http,https filter = apache-getphp action = iptables-multiport[name=apache-getphp, port="http,https", protocol=tcp] mail-whois[name=apache-getphp, dest=root] logpath = /srv/apache/log/access.log maxretry = 1 #filter.d/apache-getphp.conf [Definition] failregex = ^<HOST> - - (?:\[[^]]*\] )+\"(GET|POST) /(?i)(PMA|phptest|phpmyadmin|myadmin|mysql|mysqladmin|sqladmin|mypma|admin|xampp|mysqldb|mydb|db|pmadb|phpmyadmin1|phpmyadmin2|cgi-bin) ignoreregex = I know the regex is good, because if I run the test command on my access.log: fail2ban-regex /srv/apache/log/access.log /etc/fail2ban/filter.d/apache-getphp.conf I get a SUCCESS result with multiple hits, and in my log I see entries like 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpTest/zologize/axa.php HTTP/1.1" 301 585 "-" "-" 187.192.89.147 - - [13/Apr/2014:11:36:03 +0100] "GET /phpMyAdmin/scripts/setup.php HTTP/1.1" 301 593 "-" "-" Secondly I know email is configured correctly, as each time I service fail2ban restart I get an email for each of the filters stopping/starting. However despite all this no action seems to be taken when one of these requests comes in. No email with whois, and no entries in iptables. What possibly could be preventing fail2ban from taking action? (everything looks in order in fail2ban-client -d and I can see the chains have loaded with iptables -L)

  Read the article

• trouble shooting ntfs-loop-xen combination in wubi based grub of Ubuntu

  - by Registered User

  Here is a situation I installed Ubuntu on a laptop using Wubi in Windows 7 drive.*The laptop is not mine.*I have installed and things worked by now perfectly without any problem.We are trying to set up a Xen (virtualization)environment in this laptop. After setting up every thing cleanly.When I needed to boot with following grub entries menuentry "Xen Linux 2.6.32.27" { insmod ntfs set root='(hd0,2)' loopback loop0 /ubuntu/disks/root.disk set root=(loop0) multiboot /boot/xen.gz module /boot/vmlinuz-2.6.32.27 dummy=dummy root=/dev/sda2 loop=/ubuntu/disks/root.disk ro console=tty0 module /boot/initrd.img-2.6.32.27 } I got error file not found error unknown command 'multiboot' error unknown command 'module' error unknown command 'module' Now to dig this issue further I reboot the machine and go to grub command prompt and manually pass on each of the above parameters which you see in the grub entry when I reached grub> insmod multiboot then I got following message on screen error:file not found. It looks like this wubi+ grub setup has just enough modules to use loopback file on ntfs, but the ACTUAL /boot directory is on the loopback NOT ntfs (hd0,2). Therefore any attempt to read any files from (hd0,2) simply wont work, cause there's no file there.I need to use insmod multiboot and command multiboot and module which are available in grub on a normal install without Wubi.But since the laptop is not mine so I am not allowed to partition it and have to make it work in this situation only. While a normal Kernel is still booting? How can I get module multiboot in this Wubi based install.

  Read the article

• ADSL Modem/Router sometimes hands out incorrect IP addresses

  - by Peter Keevill

  My setup is as follows:- Main ADSL modem / router (switch) configured as DHCP server with address range 192.168.0.25-60 The office machines are configured with fixed IP ( not in the same address pool of course ) and hard wired to this router. A wireless access point ( Router ) is connected to provide Internet access for guests in a separate area. This router is NOT configured as a DHCP server. Wireless authentication is turned off. IP address lease times are set to 4 hours. Sometimes guests are able to connect to the wireless access point but they are not given a valid IP. They get 169.x.x.x addresses. Rebooting their machines does not resolve the problem. The only way to resolve is to reboot the main ADSL/router which is often frustrating for other users who are successfully connected with valid IP and DG. The problem seems to occur more frequently to Apple/Mac guests although it also sometimes occurs with Win machines. I personally use Ubuntu on my Laptop and thus far, never have had any problem connecting and getting a valid IP address in the guest area. One further point of note which may give a clue is that certain guests ( always Apple/Mac ) get lease times of 90 days. However, this does not 'stack out' the number of available addresses and of course, rebooting the router clears them until the next time they login.

  Read the article

• Windows 7 can't see wireless printer

  - by Chance Robertson

  I have a P1102W printer from HP. I have a Windows 7 machine. I have a MacBook Pro. I setup the printer following the instructions from the Windows 7 machine. I am able to print from the Mac but not the Windows 7 machine. And to add, I am not able to print from any Windows 7 machines. The MacBook Pro address is 198.168.2.115, the Windows machine is 192.168.2.117, and the printer in 192.168.2.140. I can ping the printer from the Mac. I can ping the Windows 7 machine from the mac. I can ping the mac from the windows 7 machine. When I try to ping the printer from the Windows 7 machine I get destination unreachable. I can browse to the printer IP address from the mac and not the Windows 7. I have turned off the firewall on the Windows 7 machine and turned on network sharing. Is there something else I am missing. I can connect the printer with a USB cable to the Windows machine and print. I can not get the Windows machine to see the printer even though they are on the same network.

  Read the article

• Can't upgrade NVIDIA GeForce 310M display driver on Acer Aspire 5745PG

  - by Emerson

  I've been for days already trying to update my video driver. I have an Acer Aspire 5745PG with a "NVIDIA GeForce 310M" board, and I was trying to run Sony Vegas video editor with Boris Continunn plugins. It happened that some of the plugins, like BCC Text Extrude wouldn't work, showing the message "Insufficient depth resolution to run Blue". I then read somewhere that updating the display driver would do the trick. That was when my nightmares started, I lost already good 3 nights trying to sort this out, without success :( The display driver that was before (and that I current have after restoring) was the version 8.16.11.8997. First thing I tried was downloading the 8.17.12.6619 driver directly from Acer, which was shown as the latest version from Acer website: http://support.acer.com/product/default.aspx?modelId=2466 Running it would say "Diver Package Failure - Setup failed to read the required Display Driver to be used with this package" I then tried directly the NVIDIA own driver, which the latest was version 296.10: http://us.download.nvidia.com/Windows/296.10/296.10-notebook-win7-winvista-64bit-international-whql.exe That gave me similar error message :/ So after some researching I found out that some people had the same issue and they had to change the configuration file to allow the installer to recognize this NVIDIA board: http://forums.nvidia.com/index.php?showtopic=222904 That topic said to look for the "Device Instance Id" property of the "NVIDIA GeForce 310M" display , which I couldn't find, instead I found the "Hardware Id", which seemed to be the right one. I followed the instructions and changed the inf file first for the Acer installation, and after for the NVIDIA own driver. It actually managed to go ahead with the installation in both instances, but the only thing I got was a black screen, while the computer still apeared to be running fine. I had to hard reset, and then it would come back with generic vga driver. I could only get my display back using the recovery function. I imagine thousands of this notebook was sold, and it can't have its driver updated?? Could someone help me with this?? Thanks Echo

  Read the article

• Terminal Server in Windows Server 2003

  - by Hemal

  I have a confusion regarding what I am doing here. At present I have a Windows Server 2003 server with SP2. I have assigned RAS/VPN server role to it (through Manage my server wizard) and in my router, I setup the IP address of my RAS/VPN server as PPTP server. Staff leave their workstations ON all the time and access them from home through RDP. They first connect thorugh VPN & in the RDC they simply type their respective IP or computer name to access the office network from home. Everything works fine so far except: Staff have to leave compuers always ON in the office Speed is very slow depend how many staff members access the VPN network I was told to install and configure Terminal service to improve this situation. I already added TS Role in the server but I don't know how to clients can access the TS server from home or remote location. I really appreciate any good links or guidence from the experts in this group regarding this. Thank you in advance for any replies!

  Read the article

• Preventing DDOS/SYN attacks (as far as possible)

  - by Godius

  Recently my CENTOS machine has been under many attacks. I run MRTG and the TCP connections graph shoots up like crazy when an attack is going on. It results in the machine becoming inaccessible. My MRTG graph: mrtg graph This is my current /etc/sysctl.conf config # Kernel sysctl configuration file for Red Hat Linux # # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and # sysctl.conf(5) for more details. # Controls IP packet forwarding net.ipv4.ip_forward = 0 # Controls source route verification net.ipv4.conf.default.rp_filter = 1 # Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 # Controls the System Request debugging functionality of the kernel kernel.sysrq = 1 # Controls whether core dumps will append the PID to the core filename # Useful for debugging multi-threaded applications kernel.core_uses_pid = 1 # Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 # Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 # Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 # Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 # Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_syncookies = 1 net.ipv4.icmp_echo_ignore_broadcasts = 1 net.ipv4.conf.all.accept_redirects = 0 net.ipv6.conf.all.accept_redirects = 0 net.ipv4.conf.all.send_redirects = 0 net.ipv4.conf.all.accept_source_route = 0 net.ipv4.conf.all.rp_filter = 1 net.ipv4.tcp_max_syn_backlog = 1280 Futher more in my Iptables file (/etc/sysconfig/iptables ) I only have this setup # Generated by iptables-save v1.3.5 on Mon Feb 14 07:07:31 2011 *filter :INPUT ACCEPT [1139630:287215872] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [1222418:555508541] Together with the settings above, there are about 800 IP's blocked via the iptables file by lines like: -A INPUT -s 82.77.119.47 -j DROP These have all been added by my hoster, when Ive emailed them in the past about attacks. Im no expert, but im not sure if this is ideal. My question is, what are some good things to add to the iptables file and possibly other files which would make it harder for the attackers to attack my machine without closing out any non-attacking users. Thanks in advance!

  Read the article

• Archive Manager, SQL 2005 and MaxTokenSize high CPU

  - by Tim Alexander

  So, I posted this question a few days ago: Impact of increasing the MaxTokenSize for Kerberos Tickets Since then the thought was to test our settings on two member servers, one with IIS and one without. I setup two GPOs to configure the MaxTokenSize reg setting to 48000 and MaxFieldLength/MaxRequestBytes to 64200 (based on MS KB2020943, these are set at 4/3 * T + 200). The member server seemed to work ok (a devalued tape backup server). The IIS server however has had some strange repercussions. The IIS Sserver host Quest Software Archive Manager (AM) 4.5 that communicates with SQL Server 2005 Enterprise on Server 2003 R2. After the changes all looked good until the SQL Server hit 100% CPU. I have removed the GPOS, removed the reg values and even replaced them with defaults (12000 for token size and can't remember the other one but was in a blog post about the issue in my other post). No change. Bouncing the IIS Server stops the high CPU and a colleague has looked at the SQL server and it is definitely the AM connection taking up the time/work on the SQL server. I haven't changed the reg values on the SQL server or the DCs but am reluctant to do so without understanding why this has happened. I am guessing its to do with the overriding auth and group issue we have but I am not seeing Kerberos errors in either event log. Has anyone seen something similar or does anyone have some tips? Was definitely blindsided by the Kerberos issue and am swimming against the tide to keep things functioning.

  Read the article

• v2v of RHEL5 box - issues with retaining MAC address

  - by Alex Berry

  For the last week we have been troubleshooting a customer's Red Hat Virtual Machine running on ESXi. We've been using Veeam to try to create a replica off-site and have been having getting it to work on a decent schedule and recently we noticed that there were issues with orphaned snapshots while looking at the datastore. You can see several snapshots in the same folder and it's causing issues with replication and backup, so we decided the cleanest way was to v2v the machine to another datastore so that we had a clean single-vmdk setup to work with, this is where our trouble started. We first started off with a v2v using vmware converter and connecting to the powered on machine as we were having issues doing an offline v2v. This copied fine but when I tried to set a static MAC using this article http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=507 the new VM wouldn't take the address, it simply obtained a new MAC, received a dhcp lease and then would only boot up to a blank red screen, never the login screen. So the next step was to do an offline v2v, once we finally got it working. Same thing, followed the kb to the letter and still it wouldn't take the MAC. I then tried it again and upon completion I compared both old and new VMX file, copying every identifier and variable possible, then unregistered both VMs, uploaded the new VMX file and booted, only to see the same results. Finally I did the same as above but I copied the disk using DD to a second attached vmdk and then attached this to the new VM, and still no luck. After downloading the modified VMX file after the first boot and comparing it to the original I created I found that the bios uuid had changed from the one I typed in manually, so I'm assuming this may be the snagging point, but I have no idea. I've never had this issue before on a P2V and I'm just wondering if someone could shed some light on this, maybe it's to do with RHEL licencing?

  Read the article

• What's needed in a complete ASP.NET environment?

  - by Christian W

  We have a ASP3.0 application with a few ASP.NET (2.0) dittys mixed in. (Our longtime goal is to migrate everything to ASP.NET but that's not important for this issue) Our current test/deploy workflow is like this: 1 Use notepad++ or VS2008 to fix a bug/feature (depending on what I have open) 2 Open my virtual test-server 3 Copy the fixed file over, either with explorer, or if I can be bothered to open it, WinMerge 4 Test that the fix works 5 Close the virtual test-server 6 Connect to our host with VPN 7 Use WinMerge to update the files necessary 8 Pray to higher powers that the production environment is not so different that something bombs. To make things worse, only I have access to my "test-server". So I'm the only one testing it. I really want to make this a bit more robust, I even have a subversion setup running. But I always forget to commit changes... And I don't even work in my checked out folder, but a copy of what is currently in production... Can someone recommend some good reading on deploying, testing, staging and stuff like that. I currently use VS2008 and want to use subversion or GIT (or any other free VCS). Since I'm the only developer, teamsystem is not really an option (cost-related). I have found myself developing an "improved" feature, only to find a bug in the same feature in the production system. And since my "improved" feature incorporated deleting some old functionality, I have to fix bugs directly in production... That's not a fun feeling... (I have inherited this system recently... So it's not directly my fault that it is like this ;) )

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• System State Backup Retention Policies

  - by isoscelestriangle

  I was wondering if there was a general consensus on how long to keep system state backups. I am trying to reevaluate our current backup process, and trying to get a good handle on our current storage requirements. Our current setup involves tapes and sending backups offsite with Barracuda Networks. We have been doing our system state backups with Barracuda now, which does full backups daily, leaving our storage requirements growing quite quickly. My boss is a little too gung-ho with backups and wants our system states saved for quite a while. We currently have 5 days of nightlies, 5 weeklies, 3 monthlies, and so on. I think this is quite overkill for system state backups. My boss wants the ability to go back in time to find when an issue appeared, but I don't think that is practical. Many things change in the course of several months. I also think it would be hard not to notice problems with our DCs and other servers for several months. I would think that a previous week's snapshot and the current week's dailies would suffice. Any advice or reading you can point me to? Thanks!

  Read the article

• Update a bootable OS X drive clone with rsync?

  - by Joe

  The question: is it possible to keep a boot-able backup drive clone of OS X updated with rsync? If rsync is not a viable option are there alternatives? The Setup: My situation is as shown above. One internal Samsung 840 SSD [120g] in use as my OS X 10.8 boot disk on a recent model Mac Mini. I have successfully cloned that drive with disk utility to a 125g partition of another HDD in an external USB 3 enclosure and at that point I am able to boot to it. The Goal: As my last system went out in a fiery blaze taking much valuable data with it, I have a new respect for a proper backup solution and really want to do this right. My goal is to achieve an automated differential backup/update from Disk A to Disk B while most importantly maintaining boot-ability on the external drive. And I would prefer to do this differentially to minimize stress on the drives. Hence rsync was the first thing to come to mind. What I have tried: following along with Jamie Zawinski's differential mac bootable backup solution running this manually initially worked - i tested it with only very miniscule file change and everything was fine / external booted and all. now after subsequent passes rsync fails throwing errors particularly relating to updating 'boot.efi' (not at the machine currently I will update the precise log message once I return home) is this a drive partition size issue? does rsync require more space? if it cant be done, are there any alternatives? i've heard whispers of dd

  Read the article

< Previous Page | 483 484 485 486 487 488 489 490 491 492 493 494  | Next Page >