Search Results

Search found 13434 results on 538 pages for 'boot on power up'.

Page 489/538 | < Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• Windows 7 DHCP Default Gateway not Overridden by manual Default Gateway

  - by dgwilson

  We have recently installed Windows 7 for student computers. All student computers must be routed through our content filter which is located at 192.168.0.63. This was done in WinXP by adding a Default Gateway in the network adapter settings TCP/IP Properties Advanced Default Gateway. All teacher computers are routed through the DHCP assigned Default Gateway of 192.168.0.1. In WinXP the dhcp default gateway was correctly overridden by this manual setting. In Win7 it appears that the dhcp default gateway is retained and the manual one is added to the list so that there are two with the dhcp one having the primary metric. I have tried several ways to remove the dhcp default gateway such as, running the "route delete 0.0.0.0 192.168.0.1" command. Doing this from an administrator command prompt works but it just resets upon reboot. I've tried adding this command to the registry's Run section but it seems to run as a non-administrator and therefore will not complete successfully. Is there any way to prevent this and force the manual default gateway to override the dhcp one? Or to remove the dhcp assigned one automatically on boot/login? HELP! We CANNOT allow student computers to connect to the internet without going through the content filter.

  Read the article

• Linux: Force fsck of a read-only mounted filesystem?

  - by Timothy Miller

  I'm developing for a headless embedded appliance, running CentOS 6.2. The user can connect a keyboard, but not a monitor, and a serial console would require opening the case, something we don't want the user to have to do. This all pretty much obviates the possibility of using a recovery USB drive to boot from, unless all it does is blindly reimage the harddrive. I would like to provide some recovery facilities, and I have written a tool that comes up on /dev/tty1 in place of getty to provide these functions. One such function is fsck. I have found out how to remount the root and other file systems read-only. Now that they are read-only, it should be safe to fsck them and then reboot. Unfortunately, fsck complains to me that the filesystems are mounted and refuses to do anything. How can I force fsck to run on a read-only mounted partition? Based on my research, this is going to have to be something obscure. "-f" just means to force repair of a clean (but unmounted) partition. I need to repair a clean or unclean mounted partition. From what I read, this is something "only experts" should do, but no one has bothered to explain how the experts do it. I'm hoping someone can reveal this to me. BTW, I've noticed that e2fsck 1.42.4 on Gentoo will let you fsck a mounted partition, even mounted read-write, but it seems only to do so if fsck is run from a terminal, so it can ask the user if they're sure they want to do something so dangerous. I'm not sure if the CentOS version does the same thing, but it appears that fsck CAN repair a mounted partition, but it flatly refuses to when not run from a terminal. One last-resort option is for me to compile my own hacked fsck. But I'm afraid I'll mess it up in some unexpected way. Thanks! Note: Originally posted here.

  Read the article

• Installing Linux on an Asus p8z68-m PRO Motherboard

  - by Holland

  Here is a challenge: how is this done? I've tried disabling the ASM1061 controller in the Onboard Devices section, using Wubi, booting from USB (as I don't have a DVD drive, yet), and even booting from RAID/IDE (with AHCI as the default) to do this. Still, no dice. Google shows up virtually nothing related about Linux and this mobo, apart from a people just saying "disable ASMedia" (which, I assume is the ASM1061 controller, as that's all I see - apart from the USB 3.0, which I disabled already) and it hasn't really helped much. Thus, what is wrong here? Edit My problem is that I cannot boot Linux via USB or a simple Windows installer such as Wubi (for Ubuntu). I wind up getting error messages along the lines of write cache failed, along with many other cryptic error messages similar to the following: [ 1400.351374] sd 4:0:0:0: [sdb] Test WP failed, assume Write Enabled [ 1400.353433] sd 4:0:0:0: [sdb] Asking for cache data failed [ 1400.356601] sd 4:0:0:0: [sdb] Assuming drive cache: write through This seems to be common for Asus P8Z68-M Pro motherboards, with the only notable solution being to "disable ASMedia", which, as I said before, I'm guessing is the ASM1061 controller on the motherboard. Despite already disabling this, I have tried this with both Fedora and Ubuntu without any success. I need to know what I can do about this; has anyone ran into something similar or heard about this issue before? I know these motherboards are relatively new...

  Read the article

• How to install QEMU on Damn Small Linux?

  - by user2934303

  i'm trying to install QEMU on a Damn Small Linux installation in order to emulate pentium features in a 486 computer. Though DSL was descontinued, it's the only linux that runs reasonably on the 486 processor, most recent kernels doesn't even boot on 486 architecture. I tried Tiny Core Linux, but it doesn't work in 486, so i seem to have no escape here. The most recent image of DSL is from 2008, it uses kernel 2.4.x, and i couldn't find a way to compile QEMU on it. Firstly, it lacks several compile tools needed for compiling it, and, it have several dependency problems. I tried some pre-compiled packages, but the only one that worked was a QEMU 5.2 RPM package (it didn't had dependency problems), and it was way too old, it wasn't capable of running windows yet, it just gave me the option of emulating a code, not a full OS as windows, and it also didn't give me the option to choose which architecture i wanted it to emulate (-cpu option). Can anyone help me with this? Also, if someone can think of some alternative to it, i'd be grateful. Thanks.

  Read the article

• Unable to activate Windows XP

  - by Josh Kelley

  The latest round of Patch Tuesday updates left my Windows XP computer unbootable. ("Fatal System Error: The Windows Logon Process system process terminated unexpectedly.") After much messing around with the recovery console, an XP CD's repair mode, and manually copying registry files around, I have a system that can boot again. However, I overwrote my OEM XP installation's activation information while trying to run a retail XP CD's setup, so it needs reactivation. Here's my problem: I cannot activate it at all. I log in, Windows tells me I have to activate to continue, I click Yes, and absolutely nothing happens: no windows, no response to keyboard or mouse, no response to Ctrl-Alt-Del, nothing. Safe mode works, but I can't activate in safe mode (EDIT: not even safe mode with networking). I read a trick online of pressing [Windows Key]+U to bring up the Microsoft Narrator, and that works, but clicking its Microsoft Web Site link does nothing. My last attempt to resolve this was to reinstall Windows off of the OEM CD. Now I have two parallel Windows installations, both on the same hard drive, one with all of my stuff and no way to activate it, one fully activated with no usable programs. Any ideas? Any way to activate in safe mode? Any way to copy activation information from my activated installation to my unactivated installation (since they're both on the same hard drive)?

  Read the article

• Acer Aspire one is falling apart on Ubuntu

  - by Narcolapser

  Question: How do I have my netbook detect and install hardware? Info: I have an Acer Aspire One, it came with windows XP and I loaded it with Win7. I decided I wanted to change to Ubuntu so I tried Ubuntu netbook remix, which failed horribly, and so after attempting 3 or so other OS's I ended with Ubuntu Desktop 9.10. Which worked fine for a while, but there were some minor issues so I asked a question about it here and decided to change my OS again. This last weekend I tried mandriva like that guy in my other question suggested, no success. when I had though my netbook lost the ability to use it's touch pad, I didn't think much of it, just thought it must be a driver or something. But When Mandriva failed, and I also while I was at it tried Damn small linux and Debian, which both failed to, I decided to switch back to Ubuntu Desktop(some where in here my keyboard stopped working for one attempt to). But first I gave the netbook remix one more try. it worked this time, with the exception of it didn't have any networking. I thought it was a driver issue again and finished the weekend with ubuntu desktop 9.10 again. But now things get really crazy. it doesn't know it has a wireless card or an ethernet card. It doesn't know my phone is connected trying to provide wireless broadband either. I'm clueless on what could be the problem. And with only a minimal amount of experience with Ubuntu can't navigate the entire interface with only my keyboard(it doesn't detect a USB mouse when I plug it in, it had when I installed it. in fact the network interfaces were working just fine when I live boot ubuntu to installed it). Even so, I don't know where to go or what to do to make it recognize it's hardware. I'm in a dire situation, any help is welcome.

  Read the article

• Flash alternative for iBook Mac?

  - by Hunter Dolan

  I have a old Apple iBook G4 that I decided to hook up to my main TV. I like the setup because I can surf the internet on my TV now. The only thing that I can't seem to do is watch Flash videos. Apparently Flash Player 10 doesn't play nice with the iBook's graphics card's GPU, leaving all the graphics processing to the CPU which is a disaster. Others suggested downgrading to Flash Player 9, I did that, and youtube worked fine, but Hulu (The main reason I wanted to hook it up to the TV in the first place) did not. Anyone know of a Flash alternative or a Flash 10 fix for the iBook? Or even a Hulu client that doesn't require Flash. Here are my iBook's Specs Model Name: iBook G4 <br> Model Identifier: PowerBook6,5 <br> Processor Name: PowerPC G4 (1.2) <br> Processor Speed: 1.2 GHz <br> Number Of CPUs: 1 <br> L2 Cache (per CPU): 512 KB <br> Memory: 512 MB <br> Bus Speed: 133 MHz <br> Boot ROM Version: 4.8.7f1 <br> Mac OS X Version: 10.5.8 <br> PS: Don't tell me that I need to buy a new computer. I know that I would have better results with a new computer but I don't want to buy a new computer just for Hulu.

  Read the article

• Setup of high-end web server and DB server cluster on Amazon EC2: Is this how it's done?

  - by user1086584

  Amazon is so technical, I want to confirm that my understanding is correct. We have a large 500 GB database. (OrientDB.) We will have it mirrored to one another in the same Availability Zone. We believe the database size will grow rapidly. The plan is: Get 4 large instances that are compatible types with Placement Groups (as well as ideally, Enhanced Networking) (2 for web, 2 for DB.) We use an EBS-backed instances to store our operating system. Discussion here: http://alestic.com/2012/01/ec2-ebs-boot-recommended We can set up ephemeral SSD instance storage as swap space. (But it is lost after even a reboot. I hear its hard to add ephemeral storage if booting from EBS, but possible.) For offsite backup, we will take periodic snapshots and store them on S3. Obviously we need to ensure the database is in a safe state when that snapshot happens to avoid corruption. (Any hints here, aside from shutting down the DB?) If the database gets too big, we need to create a EBS volume that's larger. We can use RAID to break the 1 TB limit: http://alestic.com/2009/06/ec2-ebs-raid Static assets on web servers will be stored on S3. Is that correct? Or am I missing something?

  Read the article

• DD-WRT router causing IP address conflicts across network

  - by r.tanner.f

  My DD-WRT router has lost its mind! I just set up two DD-WRT routers, one as a WAP (working fine) and one in Client Bridge (routed) mode (the problem). Not long after setup I started seeing IP address conflicts on other machines. The event log always points the finger at my Client Bridge router's MAC address. Neighbour table overflow The log on my router is flooded with Neighbour table overflow errors. These start a minute or two after boot. The network is rather large, with +200 IP addresses being used in this subnet. The other router shows no such errors. Mass ARP requests from 1.1.1.1 I'm also seeing constant ARP requests (with the problem router's MAC address) from 1.1.1.1. Seems like it's bugging everything on the network for its MAC address and then promptly forgetting it (or never receiving a response). Configuration: Model: Buffalo N600 Firmware: DD-WRT v24SP2-MULTI (03/21/11) Wireless Mode: Client Bridge (routed) I'm not sure what configuration details are relevant and I'd rather not have comments flooded, so just ping me in this chat if you want to know something. Why is my router stealing IP addresses and how can I stop it?

  Read the article

• Intel Rapid Storage Technology (pre-OS) driver installation

  - by Nero theZero

  My desktop machine is built on Gigabyte GA-Z87-UD3H and Gigabyte provides the latest driver for Intel Rapid Storage Technology (IRST), which I installed after installing the OS. Same goes for my Lenovo Thinkpad-T420. And for both machine, checking the controller device under the IDE ATA/ATAPI Controllers section in Device Manager I see the driver has been updated to the latest version. I set the SATA controller to AHCI from BIOS On the desktop machine I have one WD 2TB BLACK & one WD 3TB Green I don’t use RAID, & no chance of using in near future, but according to Intel IRST improves performance in single disk scenario too. Now I have the following questions – What is the actual purpose of IRST (pre-OS install) driver that doesn’t get served with a post-OS driver that I installed? There must be some difference, otherwise there wouldn’t be a pre-OS version of the driver. Right? In the pre-OS procedure (loading the drivers at OS-installation time) after successfully completing the OS installation, do I need that post-OS driver? Because after installing from that one I got a quick launch icon that runs the IRST configuration application. Where do get that after installing the pre-OS driver? As it is “pre-OS”, when I load it at OS-installation time, does it updates anything at BIOS level or anywhere other than HDD? That’s because I’m going to dual boot Windows 7 with Windows 8.1, and after installing Windows 7 when I install Windows 8.1 & load the IRST driver for that, is there any chance of any “overwriting” or OS-incompatibility? In short, is there anything specific to follow while installing the second OS?

  Read the article

• Debian Squeeze vzquota

  - by benjamin

  Hello, Apparently, I got Debian Squeeze (Debian 6) to work on a VPS using debootstrap and chroot as described here. Subsequent installation of the harden, exim4, mysql-server packages failed partially. Relevant information: insserv: warning: script 'S10vzquota' missing LSB tags and overrides insserv: warning: script is corrupt or invalid: /etc/init.d/../rc6.d/S00vzreboot insserv: warning: script 'vzquota' missing LSB tags and overrides insserv: There is a loop between service vzquota and stop-bootlogd if started insserv: loop involving service stop-bootlogd at depth 2 insserv: loop involving service vzquota at depth 1 insserv: loop involving service rsyslog at depth 1 insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: There is a loop between service vzquota and stop-bootlogd if started insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: Starting vzquota depends on stop-bootlogd and therefore on system facility `$all' which can not be true! insserv: exiting now without changing boot order! update-rc.d: error: insserv rejected the script header dpkg: error processing exim4-base (--configure): subprocess installed post-installation script returned error exit status 1 Any suggestions? Keywords: vzquota debian squeeze installation vps, virtual private server.

  Read the article

• Hard drive failed, suspected filesystem corruption, still cannot salvage any data from harddrive

  - by Hippy-Head

  Firstly, I am terribly sorry if this is a duplicate, but I couldn't find a similar issue to mine, so here goes. I have a 1TB hdd bought around 8 months ago used as backup hard drive. I have not used the drive for a period of time whatsoever, and when I was trying to get back to some files on it, it was completely wiped just like that. At first it would not boot I tried everything from command line chkdsk and filesystem recovery software to rebuilt it. After a few attempts I managed to initialize it, at that time it was an achievement. The problems started when I tried to recover the data inside, I have used A LOT of software free and commercial software on both Mac and Windows, with the help of cmd or Terminal commands, however no data of any kind was recovered, even after leaving it thoroughly scan for around 9-10 hours all night sometimes longer, with no results at all. I am somewhat desperate, I am usually good at retrieving data from corrupt hard drives, but this is not the case. Call me paranoid, but I do not want to give it to someone to fix it for me, as I have a lot of photos and personal stuff that I do not want anyone to see.

  Read the article

• ext4 filesystem corruption -- maybe hardware error?

  - by pts

  I'm getting these errors in dmesg after about half an hour after I turn on the computer: [ 1355.677957] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1318420: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251700offset=0(0), inode=1802725748, rec_len=179136, name_len=32 [ 1355.677973] Aborting journal on device sda2-8. [ 1355.678101] EXT4-fs (sda2): Remounting filesystem read-only [ 1355.690144] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1318416: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251699offset=0(0), inode=2194783952, rec_len=53280, name_len=152 [ 1356.864720] EXT4-fs error (device sda2): htree_dirblock_to_tree: inode #1312795: (comm updatedb.mlocat) bad entry in directory: directory entry across blocks - block=5251176offset=1460(13748), inode=1432317541, rec_len=208208, name_len=119 /dev/sda is an SSD, and it's using the noop scheduler. /etc/fstab entry: UUID=acb4eefa-48ff-4ee1-bb5f-2dccce7d011f / ext4 errors=remount-ro,noatime,discard,user_xattr 0 1 System information: $ cat /proc/mounts | grep /dev/sd /dev/sda1 /boot ext2 rw,noatime,errors=continue 0 0 $ cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=10.04 DISTRIB_CODENAME=lucid DISTRIB_DESCRIPTION="Ubuntu 10.04.3 LTS" $ uname -a Linux leetpad 2.6.35-30-generic-pae #61~lucid1-Ubuntu SMP Thu Oct 13 21:14:29 UTC 2011 i686 GNU/Linux I've run memtest for 7 hours, it didn't found any memory errors. Any obvious ideas what can go wrong in this case? The most reasonable thing I can imagine is that the SSD is silently dropping some write requests, which eventually leads to an EXT4 filesystem inconsistency (but no disk I/O errors). How can this happen? Is there a relevant configuration option I should ensure to be set correctly? What tools should I use to diagnose the hardware failures? Would it be possible to diagnose the SSD failure without overwriting data?

  Read the article

• Umount stale glusterfs partition

  - by Khaled

  I am using glusterfs on several Ubuntu servers: two of them are running glusterfs servers in replication mode. Without any clear error, the glusterfs partition became stale and the system shows this error when I try to access the stale partition: Transport endpoint is not connected Also, when running ls -l on the parent folder I get: d????????? ? ? ? ? ? myfolder I tried all types of commands that I can find to umount this partition, but I could not get it done: umount -l /path/to/mount/point umount -f /path/to/mount/point Also, using fuser command to show processes accessing this folder did not work. Unload the fuse kernel module can not be done as it is clear from the kernel config that fuse is built into the kernel and not a loadable module. I found this line in /boot/config-2.6.32-24-server CONFIG_FUSE_FS=y I have been left with two options: Reboot the system. Create another mount point like myfolder2 and mount this again using sudo glusterfs -f /etc/glustefs/glusterfs.vol /path/to/folder2. Of course, I have chosen to go with option 2. Anyone faced such an issue before? Anyone has a better solution for such a case?

  Read the article

• Why would my HDD main partition suddenly become hidden?

  - by Luis Oscar

  A few days ago I was using my computer as usual and I turned it off. The next day it wouldn't boot up. It just stayed after the hardware diagnostic window on the intermittent underscore screen. So clearly It wasn't booting up. I tried turning it on and off a couple of times with no avail. Finally I used windows 7 disk and it seemed as if there was no HDD. not even the installation would see the HDD. So i thought it was dead, i bought a new one installed it with windows and used a external case with the old HDD. plug it in and still couldn't see it. I finally downloaded a partition program EASUS or something and my HDD was there listed WITHOUT a system letter. I could however explore it and i set it as Unhidden and it came back to life. I could see it normally. I really just wish someone could explain to me what happened here, was it a virus? does it means the HDD is about to die? How can i prevent this or what should I do now? should i stop using this OLD HDD? Thanks

  Read the article

• Disaster After Removing Two HDD From LaCie RAID 0 Case

  - by John

  This is the second time this has happened. I own a LaCie IDE RAID 0 Enclosure and the RAID went bad. The system gave me a warning that the data could be read from the RAID but that nothing could be written, and to remove the data ASAP. I did that and erased and reinitialized the RAID. System reported it was fine, no issues. I wrote to the RAID again and the system reported the same issue. So, I removed the drives and tested them individually thinking one must have gone bad. Sure enough, one HDD reported all bad blocks, every single one after the Master Boot Record. I didn't think much about it because of the age of the drives, 5 years old. So, I bought two new drives plugged them in and started up the RAID again. Exactly the same thing happened. All was fine after initializing the RAID and then the next day after powering on the RAID the exact same issue. The HDD sitting in the same position as the first "bad" HDD reported all bad blocks. Obviously, this is an issue with LaCie's bridge board not with the drives. No utility I have used has been able to bring this HDD back to life. I thought I would just copy the MBR from the good drive to the new one using a sector editor but am hesitant. Is it possible the firmware on the HDD has been corrupted by the LaCie bridge board?? What else could be the cause of such an issue? How can I fix this drive?

  Read the article

• Configuring WPA WiFi in Ubuntu 10.10

  - by sma

  I am trying to configure my wireless network on my laptop running Ubuntu 10.10 and am having a bit of difficulty. I am a complete Linux newb, but want to learn it, hence the reason I'm trying to set this up. Here's the vitals: It is a Gateway 600 YG2 laptop. It was previously running Windows XP, but I installed Ubuntu 10.10 in place of it (not a dual boot, I removed XP altogether). I have an old wireless card that I'm trying to resurrect. I haven't really used the card in a couple years, but it seems to still work, I just can't connect to my home's wireless network. The card is a Linksys WPC11 v2.5. When I plug it in, Ubuntu recognizes the network, but won't connect to it. My home network uses WPA encryption and the only connection type that Ubuntu's network manager is giving me is WEP and then it asks for a key -- I have no idea what that key should be. So, basically, I'm asking, is there a way I can instead connect through WPA? I've tried creating a new connection in network manager, but that won't work, it keeps falling back to the WEP connection and asking me for a key. I have tried to install the XP driver using ndiswrapper but I don't know if that's working or not. Is there a way to tell if: A) the card is working as it should B) the correct drivers are installed (again, I installed the XP one using ndiswrapper NET8180.INF, but I'm not sure what to do next) Any help would be appreciated. Thank you.

  Read the article

• Ubuntu 10.04 - Add RAID 1 Array?

  - by N Rahl

  I have an existing Ubuntu 10.04 desktop system setup and running on a hard drive (Drive A). I'd like to add 2 more hard drives (Drives B & C, same size) to the system and mount them as a RAID 1 array. How do I do that? I know how to create RAID arrays during the installation, but I don't want to reinstall my system, and I shouldn't have to since my system files will stay on their own drive separate from the RAID array. I've physically added both drives to the system, and formatted them as EXT3 with gparted. Ubuntu's disk utility has a "create raid" option, but it won't let me select any of my drives (it thinks they're all full). I don't mind using mdadm, but I've found several guides that are old, and give conflicting advice. Some say I have to edit an /etc/raidtab file, some say this is done automatically. So what's the current (Ubuntu 10.04) preferred way of adding a RAID 1 to an existing system? It should turn into a raid at boot, and mount itself in /home/myname/files/. Thanks!

  Read the article

• Xen networking is inconsistent in multiple ways

  - by WildVelociraptor

  I've been running xen for a few weeks now on an Ubuntu 12.04 server. I've got 3 guests: a Windows Server 2003 guest, an Ubuntu guest, and a Windows 7 Guest. My Server 2003 guest seems to work fine; I can ping it from the network, the hostname resolves correctly, and it can see the internet. This guest is attached to xenbr0, and its IP is 10.100.1.21. My Win7 guest is what is driving me crazy. I use the same configuration script as a base, changing the important parts (hostname and boot disk, mainly). It installed correctly, and is currently running, but I am unable to ping this guest. It's hostname is "alexander", with an IP of 10.100.1.22. It is also using xenbr0. The guest can ping the firewall and various IP addressess, but seems unable to resolve hostnames. Now heres the weird part: when I use rdesktop (RDP client) from my laptop (not the xen host) to connect to alexander, it works just fine. It apparently resolves the hostname fine, and does the same with the IP address. So, can someone tell me why I can access this guest using RDP, but not using ping, nslookup, traceroute, etc? It's apparently invisible to all but RDP. Also, is it okay to use two guests on the same bridge, or do i need different ones for each guest? Thanks in advance for any help. Regards

  Read the article

• Toshiba Satellite U500 - Totally Damaged LCD

  - by ivan

  I accidentally damaged my Toshiba Satellite U500 laptop which resulted in a totally unusable LCD. The LCD panel has some cracks on it, and I can only see black & white spots; the laptop frame became broken/bent to where I can partially see inside the PC; the accident disassembled the CD tray, and bent the keyboard frame (which now has a weird hump). The system is still working though. It responds to my inputs (eg, turning it on/off, typing my password @ Windows Login, etc). What I want to do now is to transfer all of my important data from that laptop to my external drive. But I don't know how since the LCD screen is unreadable. I know I can connect it to an external monitor or a TV (I have a Samsung 1080p TV) but I don't know how. What cable should I purchase to connect the TV? Which ports on the laptop and TV should I connect it to? Do I need press something while/after connecting it? Can I boot my laptop using the TV?

  Read the article

• two computers on same network cannot ping eachother nor view NetBios resources

  - by slava

  I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

  Read the article

• RAID 5 Install on Ubuntu Server 12.04 [closed]

  - by tarabyte

  Environment: Ubuntu Server 12.04, installing from bootable flash drive Error: No root file system is defined. Please correct this from the partitioning menu. I'm trying to set up a personal file server with software RAID 5. I just got three hard drives for this, but haven't found any solid documentation. I'm unsure what the basic way to partition my hard drives is. Can someone upload a screenshot of their "partition disks" screen so that I can compare with mine (attached)? Should I set the bootable flag? Do I need a /home partition? A /boot partition? Should I "Use [my partition] as: Ext4 journaling file system"? Or make that field "physical volume for RAID"? I am an engineer, but I have only a cursory knowledge of all-things-linux. If you know of any good learning resources I'd be happy to hear about those too (that way I don't have to blindly follow deprecated tutorials online). well, image would be here but i don't have a high enough reputation yet (please vote up :)) Thank you, References I've looked into: https://help.ubuntu.com/community/Installation/SoftwareRAID https://help.ubuntu.com/12.04/serverguide/advanced-installation.html http://forevergeeks.com/setup-ubuntu-server-with-raid-5/

  Read the article

• compile kernel 2.6.34 for Ubuntu Lucid for xen dom0 / pvops

  - by andreash

  Hi there, I'd like to compile a recent Linux kernel (2.6.34) for my Ubuntu 10.04 Lucid Lynx AMD64 box, mainly because I'd like to use it as a dom0 kernel with the recent xen4. There's plenty documentation on the web about how to compile a kernel 'Debian style'. But what I think would be nice to start with an 'official' Ubuntu config to be sure not to miss any important things and having to recompile over and over again. So what I'd like to do is compile 2.6.34, but starting with the 'official' /boot/config-2.6.32-XX from Ubuntu Lucid. The question is: How do I best do that? If I just take the config from 2.6.32, the new features from 2.6.33/34 won't be in the config. So what I'd like to do is somehow the 2.6.34 config with the original 2.6.32 one from Ubuntu. How can I best do that? Does it even make sense? Is there easier ways to achieve what I want? Thanks for your insight! A. PS: I just found a linux-image-2.6.32-bpo.4-xen-amd64 package on backports.org, but no information about it. Would it work as a dom0 kernel on Lucid?

  Read the article

• Rebinding Keys on a Dell Keyboard

  - by Maarx

  I have a Dell Multimedia Keyboard, similar to this one: It has many non-standard keys, like the small circular ones across the top, and the "Multimedia" keys above INSERT/HOME/PAGE_UP. They can be rebound through simple registry entries. Some sample ones are included below: [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey] [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\15] "ShellExecute"="C:\\Program Files (x86)\\Mozilla Firefox\\firefox.exe http://mail.google.com/mail/#inbox" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\16] "Association"=".cda" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\17] "ShellExecute"="C:\\Windows\\System32\\SnippingTool.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\18] "ShellExecute"="calc.exe" [HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Explorer\AppKey\7] "Association"="http" I've rebound the "MAIL" key to, instead of booting Outlook, to booting Firefox directed at my G-Mail account. I've rebound the button that would normally open "MY COMPUTER" to instead boot the Windows 7 "Snipping Tool", something I find very useful. Now, I'm looking to do some other things that I don't already know how to do. Note that answering this question doesn't necessarily require any knowledge about the keyboard or rebinding the keys: I can add, for any given key, a "ShellExecute" entry, and it will simply execute the following command as if it was typed at a Command Prompt. (I'm aware I dumbed that down rather significantly, but bear with me. I'm not really a Windows guy myself.) I use the volume knob for it's intended purpose, to change volume. I would like to change, however, a different key, to "reset" the Windows volume level back to exactly 50%, or, as it refers to it, "50", on it's 0-100 scale. I'm looking for the "program" (what I would type at a command prompt? these are still just Sys32 programs in the PATH, aren't they?) that, I imagine, would take arguments, to change Sound/Volume settings under Windows 7. Perhaps, for clarification, something that might take the form "C: SetVolume -slevel 50" or something.

  Read the article

< Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >