Search Results

Search found 14661 results on 587 pages for 'hibernate tools'.

Page 489/587 | < Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• chef clients behind firewall

  - by tec

  I am currently learning about chef. What I understood so far: I have to install chef-server on an own server or use the hosted chef. I have to install chef-client on the servers that I want to manage aka nodes (manually or using knife bootstrap). I installed several chef tools on my own PC that I can use to manage the nodes, e.g. knife. Now in my case the specialty is that the nodes are behind a firewall/load balancer/proxy. The nodes can access servers on the outside via NAT (http works and I can configure chef-specific hosts to work as well). However they can only be contacted from the outside via a ssh tunnel. There is really much documentation about chef available but I did not find an answer to these questions: When using knife, is it enough when I set up a ssh tunnel manually on my own PC or does the chef server need to contact the nodes? When using knife, can I configure it to setup a ssh tunnel automatically? When using the chef server web ui can I configure it to connect to the nodes via ssh tunnel or do I need a setup where I setup the tunnel myself e.g. using monit? Is this even possible with hosted chef? Instead of using knife or the web ui: Can I issue the same management commands directly on the nodes using chef-client? What solution would you recommend? Thanks a lot for taking your time to help and answering one or more of these related questions

  Read the article

• How to determine which ports are open/closed on a FIREWALL?

  - by Rahl

  It seems no one has asked this question before (most regard host-based firewalls). Anyone familiar with port scanning tools (e.g. nmap) knows all about SYN scanning, FIN scanning, and the like to determine open ports on a host machine. Question is though, how do you determine the open ports on a firewall itself (disregard whether the host you're trying to connect to behind the firewall has those particular ports open or closed). This is assuming the firewall is blocking your IP connection. Example: We all communicate with serverfault.com through port 80 (web traffic). A scan on a host would reveal port 80 is open. If serverfault.com is behind a firewall and still allows this traffic through, then we can assume the firewall has port 80 open also. Now let's assume the firewall is blocking you (e.g. your IP address is under the deny list or is missing in the allowed list). You know port 80 has to be open (it works for appropriate IP addresses), but when you (the disallowed IP) attempt any scanning, all port scan attempts on the firewall drop the packet (including port 80, which we know to be open). So, how might we accomplish a direct firewall scan to reveal open/closed ports on the firewall itself, while still using the disallowed IP?

  Read the article

• Upgrading from SQL2000 database to SQL Express 2008 R2

  - by itwb

  Hi, We have a web application which uses a MSSQL 2000 backend database. We are currently paying a ridiculous amount for Shared Hosting, with the database costs alone costing us $150 per month (MSSQL 100mb extra space is $40 per month). Our database size is 896.38 MB I am looking at getting a Virtual Private Server and upgrading the database to a MSSQL2008 Express database. I am aware that the Express version is limited to a 10GB database (with R2), and is constrained to a single CPU. I have also been offered SQL Server 2008 Web Edition for $19/per month, but I cannot find many details on the difference between Express and Web. Any suggestions here? What I would also like to know is: If we upgrade the database to MSSQL 2008 database, is there any issues with possible data transformations in the future? I.e. Is it possible to download and mount it with SQL Server 2008 Standard edition? I'm more concerned about how to get data in and out of the database through SQL Management tools. Are there any other issues that I might face? Thanks, Mike

  Read the article

• deploy LAMP config to new boxes with low/no effort

  - by user1444233

  I'm spending a lot of time setting up new Centos 6 instances. I use a VCS (Subversion) for most of the config files and all of the webapp source files (Github), but even with excellent package managers (like yum, npm, easy_install, etc.) it still takes time. I'd like to get to the point where I could try out a new potential web host by just signing up for an account, logging in and automatically sucking my standardised config onto the box. I know there are a set of tools that can help: Puppet Chef Vagrant and a set of services that sell solutions: [Jumpbox] http://www.jumpbox.com/ [BitNami Cloud] http://bitnami.org/cloud I don't mind investing time in learning a new tool, but as a no-budget start-up, I'm keen to keep monthly costs down. My biggest concern is that time spent on the server config is time away from the codebase, and that's where I think my team and I should be investing our energy, at least until we get funded and scale up a bit. I'd be grateful of some recommendations for which way to jump on config: stick with SSH and manual deploys, at least until you get big. bite the bullet and learn [say] puppet. You may only use it 8-10 times, but it pays to have such an easy tunable server bootstrap. don't bother, just pay the $100/month for a standard config service. It'll cost you $1000/year, but you should focus on the code. Other questions in this domain I use quite a complex stack (Drupal, Zend Server, MySQL, PHP, MongoDB, Python, django), but are there standard(ish) setups that include these or that I could build upon more quickly? Are the configs optimised for small, medium, large VPS (1GB, 4GB, 16GB)? How secure are they?

  Read the article

• Lost partition after restarting

  - by nxhoaf

  I have Window 7 Professional Service pack installed in my Laptop Lenovo Thinkpad t420. After formatting the disk, and install Window 7 (detailed as above), I went to Computer -- Manager -- Storage -- Disk Management to split my 300gb C partition into 2 partition: C (which is 162gb) E (which is 140gb) Is work fine for about 2 days. Today, when I turn on my computer, I'm very suprise that the E partition is disappear. I can surely confirm that I didn't do any stupid thing yesterday. And before I shut down my computer, everything was fine. In general, here is what I did during the last today (from the point that I formatted the disk, and installed Window) Format 300gb hard disk Install window 7 Install eclipse, db2, .... ( I'm a developer) Install some other tools (Open office, Skype...) Install PGP (http://www.symantec.com/encryption) <--- I'm forced to used that due to my company policy Use Computer -- Manager -- Storage -- Disk Management to split my 300gb C partition into 2 partition as described above. It worked quite well for two last days. Until day... Can you please help me to recover my lost partition ? Thank you! For more info, here is my partition info: You can also see the image here

  Read the article

• Limiting bandwidth on internal interface on Linux gateway

  - by Jack Scott

  I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

  Read the article

• Windows 32-bit and 64-bit and GPT

  - by MrLane

  I know similar questions have been asked before across several sites, but the answers at least to me have been confusing and conflicting. My understanding has always been that 64-bit Windows will create and use GPT disks just fine, but will not boot from them without a UEFI BIOS. Also my understanding WAS that 32-bit Windows could not use GPT at all and so is always restricted to 2.2TB disks, which was another reason to move to 64-bit on top of the 4GB memory limit. But I have now read that this isn't correct: 32-bit Windows will create and use GPT disks just as 64-bit does. The only resriction is that you can't boot 32-bit Windows even if you DO have a UEFI BIOS? I don't think much of the literature has explained this well. There are several tools floating around for creating virtual disks or 2.2+.8GB partition schemes and such for 32-bit systems. Why when it seems you can use GPT in 32-bit Windows anyway. It also seems that people blame MS for lagging behind with respect to all of this: but it seems the issue is with BIOS manufactures not supporting UEFI rather than MS not supporting GPT... Is my new understanding now correct?

  Read the article

• Centralized Windows/Mac Patch Management that is easy to use

  - by BiggsTRC

  I'm looking for advice on what patch management solutions you would recommend based upon your experience. I'm also looking for which ones you would not recommend based upon your experience. We have a mixed network of Windows and Mac clients. Our central servers are all Windows servers, although I have considered putting in a Mac server to better handle our Mac clients. The issue we are facing currently is that we need to maintain the patches on all of our third-party applications. Right now we use WSUS, which handles with patching of Windows and some Microsoft products but that is about it. I need something to cover the other applications, specifically things like Adobe products (Reader, Flash, Dreamweaver, etc.) Our network isn't that big (maybe 200 clients) and I don't have a person to dedicate just to patching and maintaining a patch management solution. Thus very large and complicated solutions like System Center are most likely out. I have recently been looking at Dell's Kace K1000 solution (http://www.kace.com/products/systems-management-appliance/). It seems simple and it provides a lot of tools in one package that I would like/need as well. I like the fact that it is self-contained in an appliance and that it is designed for solutions like mine. However, I'm not sure if this is the best solution. I've also looked some at Shavlik's Netchk solution (http://www.shavlik.com/netchk-protect.aspx) but I don't need an anti-virus product. However, it looks like they might have a very good patch database. My question is this: What are your thoughts on these to products? Are there better products out there? Are there issues that I'm not considering? I want something that is very good at patching a broad range of products, that is simple to use, that takes a minimal amount of management (like WSUS), and that (hopefully) works with Mac and Windows.

  Read the article

• Wordpress hacked. Disabled hacked site but bad traffic continues [closed]

  - by tetranz

  Possible Duplicate: My server's been hacked EMERGENCY My Ubuntu 10.04 LTS VPS has been hacked, probably via a WordPress site. I was alerted to it when I noticed the incoming traffic was unusually high. A WordPress site was littered with eval(base64_decode(...)) code in lots of files. My fault, I had some files writeable by www-data which shouldn't have been. I've disabled that site (a2dissite ... and restart Apache). This has reduced it but I am still getting some malware type traffic. My server runs several WordPress and Drupal sites and a home grown PHP site. I have captured traffic with tcpdump and looked at it Wireshark. It's reaching out to the login page of some Joomla sites, trying multiple logins. The traffic stops when I stop Apache. If I a2dissite every site and reload (not restart) Apache the traffic continues. At that point I have no virtual hosts running and no DocumentRoot in my apache2.conf so I don't know how Apache is still running something. I have searched the other sites with grep for likely looking php code with no success. I may have missed it but I haven't found anything suspicious in the Apache logs. I have mod-status running. I haven't really seen anything much there except that someone is still trying to do a POST to the theme page on the disabled WordPress site but they now get a 404. What should I be looking for? Are there any tools or whatever which would give me more info about how Apache is generating that traffic? Thanks

  Read the article

• Tips on setting up a virtual lab for self-learning networking topics

  - by Harry

  I'm trying to self-learn the following topics on Linux (preferably Fedora): Network programming (using sockets API), especially across proxies and firewalls Proxies (of various kinds like transparent, http, socks...), Firewalls (iptables) and 'basic' Linux security SNAT, DNAT Network admininstration power tools: nc, socat (with all its options), ssh, openssl, etc etc. Now, I know that, ideally, it would be best if I had 'enough' number of physical nodes and physical network equipment (routers, switches, etc) for this self-learning exercise. But, obviously, don't have the budget or the physical space, nor want to be wasteful -- especially, when things could perhaps be simulated/emulated in a Linux environment. I have got one personal workstation, which is a single-homed Fedora desktop with 4GB memory, 200+ GB disk, and a 4-core CPU. I may be able to get 3 to 4 additional low-end Fedora workstations. But all of these -- including mine -- will always remain strictly behind our corporate firewall :-( Now, I know I could use VirtualBox-based virtual nodes, but don't know if there are any better alternatives disk- and memory- footprint-wise. Would you be able to give me some tips or suggestions on how to get started setting up this little budget- and space-constrained 'virtual lab' of mine? For example, how would I create virtual routers? Has someone attempted this sort of thing before: namely, creating a virtual network lab behind a corporate firewall for learning/development/testing purposes? I hope my question is not vague or too open-ended. Basically, right now, I don't know how to best leverage the Linux environment and the various 'goodies' it comes with, and buying physical devices only when it is absolutely necessary.

  Read the article

• Toshiba laptop cd drive read causes OS to totally freeze

  - by Fujishiro

  Okay I'll try to write an understandable summary. Forgive me if I'll fail with that attempt though. So. There is a Toshiba Satellite notebook. Got Windows 7 x86 Professional (OEM) installed on it, everything is fine (okay.. somewhat). The problem. If you put an audio or any kind of disc into the drive, something starts to eat the PC. Back then when the owner told me about this, he put an audio disc into the lappy. Winamp caused the IO load, 100%. Tried taskkill, taskkill /T, tried powershell, EVERYTHING. You just can NOT kill winamp or anything which becomes the blocker at that time. Even if you kill almost everything, laptop won't do a clear shutdown. Also I tried to use the force switch at 'shutdown' from cmd, but no use. (So: At these times you can use the laptop, but the blocker/explorer/disc becomes gray as a non-responding app. You can try to kill them, but that won't work, nor you can shutdown the machine). (Also tried using PID, but no use. For the highest IO I used the "select columns" from Task Manager and enabled the IO columns.) My first hunch was the problematic disc, autoplay and it tries to read tries to read (still shouldn't kill the PC). Disabled autoplay, removed winamp. Tried other software, etc. Everything was ok. Few days later the owner tried to put a disc into the machine and it started to reproduce the same symptoms but with a totally different disc. Uhm what to know. Virus is not an option, protected by BitDefender (valid license) and Spybot. Thanks if you have ANY idea about this strange problem. ps.: For now, the owner uses Daemon tools + Blindwrite as an alternative for those apps which wouldnt start without the disc.

  Read the article

• Network Traffic Log

  - by Chris Becke

  Background - On my "home" network I have a Linksys WTR45GL router providing my internet access as well as a wireless AP. Connected I have * 2 Windows PCs (wired) * At least one laptop (Wired) * Some 802.11 enabled handheld consoles (PSPs) * A Nintendo Wii * Some windows XP pcs used by the people in the granny flat. Where I live, South Africa, well, 1Gb worth of monthly cap is, while not expensive, costly enough that I'd like to be sure that all the bandwidth used by devices on my network is ... well ... legitimate and not the result of neighbors parasiting my wireless, malware or just the result of "liberal" download policies in my software. I got the Linksys WRT45GL on the understanding that there were custom firmwares (DD-WRT and Tomato) that allowed bandwidth tracking, but there doesn't seem to be any facility to get a log of traffic that can be examined to see (a) which local devices were the biggest consumers of bandwidth and (b) what they were connected to. What tools are there for logging traffic such that, when it gets to that OMG moment in the month when all my bandwidth is gone, I have a chance to find out what the hell used it all up (and hopefully attempt some corrective action).

  Read the article

• Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace

  - by Nick

  I have an laptop top hard drive I was trying to use to my new media computer. The case is small and can accommodate for 2 2.5" drives, no 3.5" drives. I had been using the hard drive as storage hard drive until now. When I go to install Windows on the hard drive first I'm prompted at the bios of: Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace. And then again in the Windows Setup, informing me that the hard drive is bad. So I did a full format of the drive and tried again. Same error. So I took it out and hooked it back up to my other computer via an Sata usb adapter kit (maybe the cause?). The hard drive is recognized fine and when I scanned it for errors by going: right click -> properties -> tools -> error checking It returns that the hard drive is fine. I have tried 3 different SATA cables and multiple jumpers. When I plugged in my 1.5 tb 3.5" drive the computer that gives me the S.M.A.R.T. error on the 2.5" drive, recognizes it with no problems. Any ideas on why this is happening and how I can fix it?

  Read the article

• How much network latency is "typical" for east - west coast USA?

  - by Jeff Atwood

  At the moment we're trying to decide whether to move our datacenter from the west coast to the east coast. However, I am seeing some disturbing latency numbers from my west coast location to the east coast. Here's a sample result, retrieving a small .png logo file in Google Chrome and using the dev tools to see how long the request takes: West coast to east coast: 215 ms latency, 46 ms transfer time, 261 ms total West coast to west coast: 114 ms latency, 41 ms transfer time, 155 ms total It makes sense that Corvallis, OR is geographically closer to my location in Berkeley, CA so I expect the connection to be a bit faster.. but I'm seeing an increase in latency of +100ms when I perform the same test to the NYC server. That seems .. excessive to me. Particularly since the time spent transferring the actual data only increased 10%, yet the latency increased 100%! That feels... wrong... to me. I found a few links here that were helpful (through Google no less!) ... Does routing distance affect performance significantly? How does geography affect network latency? Latency in Internet connections from Europe to USA ... but nothing authoritative. So, is this normal? It doesn't feel normal. What is the "typical" latency I should expect when moving network packets from the east coast <--> west coast of the USA?

  Read the article

• Windows Server 2003 DHCP not handing out IPs

  - by SnOrfus

  I'm trying to setup a home server (to tinker with) as a domain controller. I've setup the domain and I've installed DHCP and setup a scope without any exclusions (with the default range of 192.168.0.1-254). My client machine is a Windows 7 (RC) machine and it has a connection but can't get an IP address. Even if I try setting the IP to a static 192.168.0.2 and there is still no connectivity. I can ping it from the server, but pinging the server from the client just times out. The only thing between the server and the client is a 24 port switch (D-Link DES-1024D). edit Ok, it turned out that the interfaces were setup backwards in the NAT settings (the internal nic connection was set to public and the external nic connection was set to private). I changed this and all was OK.... sort-of. Problem is now: If I set a static ip on the client (where I am typing this from) all is fine. BUT; when I set it to get it from DHCP, I get a correct IP from the server (192.168.0.2) but there is no internet on the client; but I can still ping the server fine from the client (which makes sense cause I was able to get an IP from it). edit I ended up just removing the Routing and DHCP server roles and just going with ICS for the time being until I get my hands on some better learning tools.

  Read the article

• Installing VirtualBox on BackTrack 5

  - by m0skit0

  I'm getting this error when running VirtualBox's installation script: $ sudo ~/Downloads/VirtualBox-4.1.14-77440-Linux_x86.run Verifying archive integrity... All good. Uncompressing VirtualBox for Linux installation........... VirtualBox Version 4.1.14 r77440 (2012-04-12T16:20:44Z) installer Removing previous installation of VirtualBox 4.1.14 r77440 from /opt/VirtualBox Installing VirtualBox to /opt/VirtualBox tar: Record size = 8 blocks Python found: python, installing bindings... Building the VirtualBox kernel modules Error! Bad return status for module build on kernel: 3.2.6 (i686) Consult the make.log in the build directory /var/lib/dkms/vboxhost/4.1.14/build/ for more information. ERROR: binary package for vboxhost: 4.1.14 not found Here's the log: $ cat /var/lib/dkms/vboxhost/4.1.14/build/make.log DKMS make.log for vboxhost-4.1.14 for kernel 3.2.6 (i686) Sun May 13 14:32:52 CEST 2012 make: Entering directory `/usr/src/linux-headers-3.2.6' /usr/src/linux-headers-3.2.6/arch/x86/Makefile:39: /usr/src/linux-headers-3.2.6/arch/x86/Makefile_32.cpu: No such file or directory make: *** No rule to make target `/usr/src/linux-headers-3.2.6/arch/x86/Makefile_32.cpu'. Stop. make: Leaving directory `/usr/src/linux-headers-3.2.6' /usr/src/linux-headers-3.2.6/arch/x86/ directory: $ ls /usr/src/linux-headers-3.2.6/arch/x86/ Kconfig Makefile ia32 lguest mm pci tools video Kconfig.cpu boot kernel lib net platform um xen Kconfig.debug crypto kvm math-emu oprofile power vdso Makefile references on "cpu" $ cat /usr/src/linux-headers-3.2.6/arch/x86/Makefile | grep cpu include $(srctree)/arch/x86/Makefile_32.cpu # FIXME - should be integrated in Makefile.cpu (Makefile_32.cpu) Before upgrading to 3.X I didn't have this problem, the script would install VB correctly. Any ideas on what might be causing this? Thanks in advance!

  Read the article

• HTTP Upload Problems

  - by jfoster

  We are running a marketplace on ColdFusion8 and IIS with a widely geographically distributed user base and have been receiving complaints of issues with some HTTP uploads. Most of the complaints are coming from geographically distant locations from our main datacenter on the US east coast. I've attempted to upload the same 70MB file from a US West coast test server to both our main site and a backup running the same code on a different network route and I saw the same issues fairly consistently in both places, so I've ruled out the code, route, and internal network errors. I've also tested uploads using both the native cf upload tag and a third party tool called SaFileUp. I saw the same issues with both upload tools, so I also don't think this is necessarily a ColdFusion problem. I don't have any problems uploading the test file from the East coast to other east coast servers, so I'm beginning to think that the distance between our users and our equipment is a factor. I've also found that smaller files are more likely to succeed than large ones (< 10MB) I tried the test upload with both IE and FF and did notice a difference in the way that the browsers seemed to handle packet errors. IE seemed to have a tough time continuing an upload after dropped / bad packets, whereas FF seemed to have the ability to gracefully resume an upload after experiencing packet problems. Has anyone experienced similar issues? Is there anything we can do on our side to make uploads more forgiving to packet loss or resumable after an error? A different upload tool etc… Do we need upload servers in more than one location to shorten the network routes between clients and servers? Does anyone think that switching uploads to SSL will help (no layer7 packet sniffing may lead to a smoother upload). Thanks.

  Read the article

• GRE Tunnel over IPsec with Loopback

  - by Alek

  I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• SQL 2000 Backup/Export Process - Can't find SQL 2000 Enterprise Manager, Can't use Mgmt Studio Expre

  - by 1nsane

  I need to make a backup of a client's SQL 2000 database, however there are a few issues preventing me from doing so using the traditional methods. I've tried using SQL Management Studio Express, but the host doesn't give sufficient privileges to create a backup and I'm getting some strange error messages. I've also tried doing the "Generate Scripts" to recreate the schema, then using the DTS Wizard to migrate the data, but the IDs set up with the identity specification property are not consistent with the live database once copied over. This results in some foreign key breakage... If I remember correctly, I was able to use Microsoft SQL 2000 Enterprise Manager to perform the task before, but I can't find this anywhere... it seems Microsoft has pulled most SQL Server 2000 stuff from their site. Does anyone know where I can find a copy of Enterprise Manager (or a trial of SQL Server 2000, which I believe comes with the component)? Or conversely, does anyone know of any other tools (preferably non-commercial) that are capable of mirroring remote SQL Server 2000 DBs? Thanks!

  Read the article

• How can I use the Homebrew Python with Homebrew MacVim on Mountain Lion?

  - by Stephen Jennings

  I originally asked and answered this question: How can I use the Homebrew Python version with Homebrew MacVim? These instructions worked on Snow Leopard using Xcode 4.0.1 and associated developer tools. However, they no longer seem to work on Mountain Lion with Xcode 4.4.1. My goal is to leave the system's version of Python completely untouched, and to only install PyPI packages into Homebrew's site-packages directory. I want to use the vim_bridge package in MacVim, so I need to compile MacVim against the Homebrew version of Python. I've edited the MacVim formula to add these to the arguments: --enable-pythoninterp=dynamic --with-python-config-dir=/usr/local/Cellar/python/2.7.3/Frameworks/Python.framework/Versions/Current/lib/python2.7/config Then I install with the command: brew install macvim --override-system-vim --custom-icons --with-cscope --with-lua However, it still seems to be somehow using Python 2.7.2 from the system. This seems strange to me because it also seems to be using the correct executable. :python print(sys.version) 2.7.2 (default, Jun 20 2012, 16:23:33) [GCC 4.2.1 Compatible Apple Clang 4.0 (tags/Apple/clang-418.0.60)] :python print(sys.executable) /usr/local/bin/python $ /usr/local/bin/python --version Python 2.7.3 $ /usr/local/bin/python -c "import sys; print(sys.version)" 2.7.3 (default, Aug 12 2012, 21:17:22) [GCC 4.2.1 Compatible Apple Clang 4.0 ((tags/Apple/clang-421.0.60))] $ readlink /usr/local/lib/python2.7/config /usr/local/Cellar/python/2.7.3/Frameworks/Python.framework/Versions/Current/lib/python2.7/config I've removed everything in /usr/local and reinstalled Homebrew by running these commands: $ ruby <(curl -fsSkL raw.github.com/mxcl/homebrew/go) $ brew install git mercurial python ruby $ brew install macvim (nope, still broken) $ brew remove macvim $ ln -s /usr/local/Cellar/python/..../python2.7/config /usr/local/lib/python2.7/config $ brew install macvim

  Read the article

• How to install QEMU on Damn Small Linux?

  - by user2934303

  i'm trying to install QEMU on a Damn Small Linux installation in order to emulate pentium features in a 486 computer. Though DSL was descontinued, it's the only linux that runs reasonably on the 486 processor, most recent kernels doesn't even boot on 486 architecture. I tried Tiny Core Linux, but it doesn't work in 486, so i seem to have no escape here. The most recent image of DSL is from 2008, it uses kernel 2.4.x, and i couldn't find a way to compile QEMU on it. Firstly, it lacks several compile tools needed for compiling it, and, it have several dependency problems. I tried some pre-compiled packages, but the only one that worked was a QEMU 5.2 RPM package (it didn't had dependency problems), and it was way too old, it wasn't capable of running windows yet, it just gave me the option of emulating a code, not a full OS as windows, and it also didn't give me the option to choose which architecture i wanted it to emulate (-cpu option). Can anyone help me with this? Also, if someone can think of some alternative to it, i'd be grateful. Thanks.

  Read the article

• Lighttpd - byte range request doesn't work. can't stream mp4

  - by w-01

  Am attempting to use the lastest flowplayer. (if it could work it would be pretty awesome btw) http://flowplayer.org One of the cool things about it is it uses the new HTML5 video element and supports random seeking/playback. In order to do this, you need a byte range request capable server on the backend. Luckily I'm using Lighttpd 1.5.0 on the backend. Unfortunately the current behavior is that when I do a random seek, the video simply restarts itself from the beginning. the docs say: "For HTML5 video you don't have to do any client side configuration. If your server supports byte range requests then seeking should work on the fly. Most servers including Apache, Nginx and Lighttpd support this." On my page, using chrome web developer tools, i can see when the video is requested, the server response headers indicate it is able to acce[t byte ranges. Accept-Ranges:bytes when I do random seek in the player, I can see that that byte ranges are request appropriately in the request header: Range: bytes=5668-10785 I can also verify the moov atom is at the front of the video file. My question here is if there is something else on the lighttpd side i'm missing in order to enable byte-range requests? The reason i ask is because the current behavior suggests that the lighttpd simply doesn't understand the byte range request and is just reserving the video from the beginning. Update it's clearer to put this here. As per RJS' suggestion I ran a curl command. in the response it looks like lighttpd is working as expected. Content-Range: bytes 1602355-18844965/18844966 Content-Length: 17242611

  Read the article

• Segmentation fault on login to mysql

  - by numberwhun

  Hello everyone! I recently did a fresh install of Ubuntu on my laptop (HP dv7, AMD Dual Core with 4 gigs RAM). I am working on installing my development environment and tools and one of the first things I was working on is getting MySQL installed. The following was my configure statement with options: ./configure --prefix=/usr/local/mysql --with-big-tables --with-unix-socket-path=/usr/local/mysql/tmp/mysql.sock --with-named-curses-libs=/lib/libncurses.so.5.7 After I did the make;make install, I did the post configuration such as setting the root password and installing the mysqld daemon in its rightful place. My issue is when I try to log in to mysql to start using it, the following shows what happens: $ mysql -u root -p Enter password: Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 1 Server version: 5.1.42 Source distribution Segmentation fault I have searched Google extensively, I have searched through the mysql bugs database and I have yet to find anything that matches my issue. Here is the contents of my my.cnf file, in case you want to see it: $ cat /etc/my.cnf [mysqld] basedir=/usr/local/mysql datadir=/usr/local/mysql socket=/usr/local/mysql/tmp/mysql.sock [mysql.server] user=mysql #basedir=/var/lib [client] socket=/usr/local/mysql/tmp/mysql.sock [mysqld_safe] err-log=/usr/local/mysql/logs/mysqld.log pid-file=/var/run/mysqld/mysqld.pid I am really hoping that someone here can tell me what has gone wrong with my installation as I would really love to know. I welcome and look forward to all responses. Thank you in advance! Best regards, Jeff

  Read the article

• Cannot open Pivot Table source file

  - by Ken

  Excel Pivot table error is: Cannot open Pivot Table source file C:\Users\UserName\AppData\Roaming\Microsoft\Excel\DatabaseName (version1).TableName I’ve seen other questions and answers with the same topic, but I think this is different. I believe I know why the error is occurring: Excel closed unexpectantly and did autosave with (version1) attached to the original file name and saved it in the C:\User etc. above , which is the default recovery location. I opened the recovered file in Excel, saved it as version1 on the server where the original file was located, deleted the original file, and renamed the version1 to the original name. When I go to PivotTable Tools? Options? Change Data Source, it shows only the Table and Range, which are correct, but it does not show the file name or path. The version1 and the renamed file both had the same structure, so the same source table was in both, by they were different files. How do I change the source file from what it is looking for to my renamed file? PS- The (version1) file that it says it is looking for is not in the autosave location, i.e. it is not at the path where it says it is looking in. Thank you for any help Ken

  Read the article

< Previous Page | 485 486 487 488 489 490 491 492 493 494 495 496  | Next Page >