Search Results

Search found 10751 results on 431 pages for 'fast forward'.

Page 49/431 | < Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >

  • Set up Linux box as WAP for MyBookLive?

    - by AcidFlask
    I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

    Read the article

  • OpenVPN server will not redirect traffic

    - by skerit
    I set up an OpenVPN server on my VPS, using this guide: http://vpsnoc.com/blog/how-to-install-openvpn-on-a-debianubuntu-vps-instantly/ And I can connect to it without problems. Connect, that is, because no traffic is being redirected. When I try to load a webpage when connected to the vpn I just get an error. This is the config file it generated: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca ca.crt cert server.crt key server.key dh dh1024.pem push "route 10.8.0.0 255.255.255.0" push "redirect-gateway" comp-lzo keepalive 10 60 ping-timer-rem persist-tun persist-key group daemon daemon This is my iptables.conf # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *raw :PREROUTING ACCEPT [37938267:10998335127] :OUTPUT ACCEPT [35616847:14165347907] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *nat :PREROUTING ACCEPT [794948:91051460] :POSTROUTING ACCEPT [1603974:108147033] :OUTPUT ACCEPT [1603974:108147033] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth1 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *mangle :PREROUTING ACCEPT [37938267:10998335127] :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616847:14165347907] :POSTROUTING ACCEPT [35680187:14169930490] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *filter :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616848:14165347947] -A INPUT -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A FORWARD -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 -A FORWARD -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A OUTPUT -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 COMMIT # Completed on Sat May 7 13:09:44 2011

    Read the article

  • iptables : how to allow incoming ftp traffic?

    - by logansama
    Hi, Still fighting my way through the jungle that is called iptables. I have managed to allow FTP access outside of our LAN: both these would work. NOTE: eth0 is the LAN interface and eth1 is the WAN interface. iptables -t filter -A FORWARD -i eth0 -p tcp --dport 20:21 -j ACCEPT or iptables -A FORWARD -i eth0 -o eth1 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But when i connect to a external FTP server i manage to log in and all is fine until it wishes to List the directory content. Then nothing happens as the data is blocked, due to the fact that i do not have a rule set up to allow it! (my last rule on the FORWARD chain is to block all traffic) I have tried a gazillion rules (many of which i did not understand) to try and allow the FTP traffic back through my server. One such rule for example was: iptables -A FORWARD -i eth1 -o eth0 -p tcp --sport 20:21 --dport 1024:65535 -j ACCEPT But i cannot get the List to work. It just times out after a while. Would anyone perhaps know how to build a rule which would allow FTP to List / allow such traffic back? Or have a link to sources i could work through? Thank you,

    Read the article

  • Possible to have different SSLCACertificateFiles under different Location in Apache (client side ssl certs)

    - by Mikko Ohtamaa
    I am setting up Apache to do smartcard authentication. The smartcard login is based on client-side SSL certificates handled by an OS driver. I have currently just one smartcard provider, but in the future there are potentially several of them. I am not sure how Apache 2.2. handles client-side certifications per Location. I did some quick testing and it somehow seemed that only the last SSLCACertificateFile directive would have been effective and this doesn't sound right. Is it possible to have different SSLCACertificateFile per Location in Apache (2.2, 2.4) as described below or is SSL protocol somehow limiting that you cannot have more than one SSLCACertificateFile per IP? Example potential config below how I wish to handle several SSLCACertificateFile on the same server to allow users to log in with different smartcard provides. <VirtualHost 127.0.0.1:443> # Real men use mod_proxy DocumentRoot "/nowhere" ServerName local-apache ServerAdmin [email protected] SSLEngine on SSLOptions +StdEnvVars +ExportCertData # Server-side HTTPS configuration SSLCertificateFile /etc/apache2/certificate-test/server.crt SSLCertificateKeyFile /etc/apache2/certificate-test/server.key # Normal SSL site traffic does not require verify client SSLVerifyClient none SSLVerifyDepth 999 # Provider 1 <Location /@@smartcard-login> SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/ca.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Provider 2 <Location /@@smartcard-login-provider-2> # For real SSLVerifyClient require SSLCACertificateFile /etc/apache2/certificate-test/provider2.crt # Apache does not natively pass forward headers # created by SSLOptions +StdEnvVars, # so we pass them forward to Python using RequestHeader # from mod_headers RequestHeader set X-Client-DN %{SSL_CLIENT_S_DN}e RequestHeader set X-Client-Verify %{SSL_CLIENT_VERIFY}e </Location> # Connect to Plone ZEO client1 running on fg ProxyPass / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ ProxyPassReverse / http://localhost:8080/VirtualHostBase/https/local-apache:443/folder_sits/sitsngta/VirtualHostRoot/ </VirtualHost>

    Read the article

  • How do I setup routing for two companies with different Internet connections on the same LAN?

    - by Clint Miller
    Here's the setup: Two companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants its own Internet connection (ISP A) and company B wants its own Internet connection (ISP B). VLANs are deployed internally to separate the two companies' networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I set up policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

    Read the article

  • Why Look and feel is not getting updated properly?

    - by swift
    I’m developing a swing application in which I have an option to change the Look and feel of the application on click of a button. Now my problem is when I click the button to change the theme it’s not properly updating the L&F of my app, say my previous theme is “noire” and I choose “MCWin” after it, but the style of the noire theme is still there Here is sample working code: package whiteboard; import java.awt.GridBagLayout; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import java.awt.event.ComponentEvent; import java.awt.event.ComponentListener; import javax.swing.JFrame; import javax.swing.JLayeredPane; import javax.swing.JMenu; import javax.swing.JMenuBar; import javax.swing.JMenuItem; import javax.swing.SwingUtilities; import javax.swing.UIManager; import javax.swing.WindowConstants; public class DiscussionBoard extends JFrame implements ComponentListener,ActionListener { // Variables declaration private JMenuItem audioMenuItem; private JMenuItem boardMenuItem; private JMenuItem exitMenuItem; private JMenuItem clientsMenuItem; private JMenuItem acryl; private JMenuItem hifi; private JMenuItem aero; private JMenuItem aluminium; private JMenuItem bernstein; private JMenuItem fast; private JMenuItem graphite; private JMenuItem luna; private JMenuItem mcwin; private JMenuItem noire; private JMenuItem smart; private JMenuBar boardMenuBar; private JMenuItem messengerMenuItem; private JMenu openMenu; private JMenu saveMenu; private JMenu themesMenu; private JMenuItem saveMessengerMenuItem; private JMenuItem saveWhiteboardMenuItem; private JMenu userMenu; JLayeredPane layerpane; /** Creates new form discussionBoard * @param connection */ public DiscussionBoard() { initComponents(); setLocationRelativeTo(null); addComponentListener(this); } private void initComponents() { boardMenuBar = new JMenuBar(); openMenu = new JMenu(); themesMenu = new JMenu(); messengerMenuItem = new JMenuItem(); boardMenuItem = new JMenuItem(); audioMenuItem = new JMenuItem(); saveMenu = new JMenu(); saveMessengerMenuItem = new JMenuItem(); saveWhiteboardMenuItem = new JMenuItem(); userMenu = new JMenu(); clientsMenuItem = new JMenuItem(); exitMenuItem = new JMenuItem(); setDefaultCloseOperation(WindowConstants.EXIT_ON_CLOSE); setLayout(new GridBagLayout()); setResizable(false); setTitle("Discussion Board"); openMenu.setText("Open"); saveMenu.setText("Save"); themesMenu.setText("Themes"); acryl = new JMenuItem("Acryl"); hifi = new JMenuItem("HiFi"); aero = new JMenuItem("Aero"); aluminium = new JMenuItem("Aluminium"); bernstein = new JMenuItem("Bernstein"); fast = new JMenuItem("Fast"); graphite = new JMenuItem("Graphite"); luna = new JMenuItem("Luna"); mcwin = new JMenuItem("MCwin"); noire = new JMenuItem("Noire"); smart = new JMenuItem("Smart"); hifi.addActionListener(this); acryl.addActionListener(this); aero.addActionListener(this); aluminium.addActionListener(this); bernstein.addActionListener(this); fast.addActionListener(this); graphite.addActionListener(this); luna.addActionListener(this); mcwin.addActionListener(this); noire.addActionListener(this); smart.addActionListener(this); messengerMenuItem.setText("Messenger"); openMenu.add(messengerMenuItem); openMenu.add(boardMenuItem); audioMenuItem.setText("Audio Messenger"); openMenu.add(audioMenuItem); exitMenuItem.setText("Exit"); exitMenuItem.addActionListener(new ActionListener() { public void actionPerformed(ActionEvent evt) { exitMenuItemActionPerformed(evt); } }); openMenu.add(exitMenuItem); boardMenuBar.add(openMenu); saveMessengerMenuItem.setText("Messenger"); saveMenu.add(saveMessengerMenuItem); saveWhiteboardMenuItem.setText("Whiteboard"); saveMenu.add(saveWhiteboardMenuItem); boardMenuBar.add(saveMenu); userMenu.setText("Users"); clientsMenuItem.setText("Current Session"); userMenu.add(clientsMenuItem); themesMenu.add(acryl); themesMenu.add(hifi); themesMenu.add(aero); themesMenu.add(aluminium); themesMenu.add(bernstein); themesMenu.add(fast); themesMenu.add(graphite); themesMenu.add(luna); themesMenu.add(mcwin); themesMenu.add(noire); themesMenu.add(smart); boardMenuBar.add(userMenu); boardMenuBar.add(themesMenu); saveMessengerMenuItem.setEnabled(false); saveWhiteboardMenuItem.setEnabled(false); setJMenuBar(boardMenuBar); setSize(1024, 740); setVisible(true); } protected void exitMenuItemActionPerformed(ActionEvent evt) { System.exit(0); } @Override public void componentHidden(ComponentEvent arg0) { } @Override public void componentMoved(ComponentEvent e) { } @Override public void componentResized(ComponentEvent arg0) { } @Override public void componentShown(ComponentEvent arg0) { } @Override public void actionPerformed(ActionEvent e) { try { if(e.getSource()==hifi) { UIManager.setLookAndFeel("javax.swing.plaf.metal.MetalLookAndFeel"); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.hifi.HiFiLookAndFeel"); enableTheme(); hifi.setEnabled(false); } else if(e.getSource()==acryl) { UIManager.setLookAndFeel("javax.swing.plaf.metal.MetalLookAndFeel"); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.acryl.AcrylLookAndFeel"); enableTheme(); acryl.setEnabled(false); } else if(e.getSource()==aero) { UIManager.setLookAndFeel("javax.swing.plaf.metal.MetalLookAndFeel"); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.aero.AeroLookAndFeel"); enableTheme(); aero.setEnabled(false); } else if(e.getSource()==aluminium) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.aluminium.AluminiumLookAndFeel"); enableTheme(); aluminium.setEnabled(false); } else if(e.getSource()==bernstein) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.bernstein.BernsteinLookAndFeel"); enableTheme(); bernstein.setEnabled(false); } else if(e.getSource()==fast) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.fast.FastLookAndFeel"); enableTheme(); fast.setEnabled(false); } else if(e.getSource()==graphite) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.graphite.GraphiteLookAndFeel"); enableTheme(); graphite.setEnabled(false); } else if(e.getSource()==luna) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.luna.LunaLookAndFeel"); enableTheme(); luna.setEnabled(false); } else if(e.getSource()==mcwin) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.mcwin.McWinLookAndFeel"); enableTheme(); mcwin.setEnabled(false); } else if(e.getSource()==noire) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.noire.NoireLookAndFeel"); enableTheme(); noire.setEnabled(false); } else if(e.getSource()==smart) { UIManager.setLookAndFeel(UIManager.getSystemLookAndFeelClassName()); SwingUtilities.updateComponentTreeUI(getRootPane()); UIManager.setLookAndFeel("com.jtattoo.plaf.smart.SmartLookAndFeel"); enableTheme(); smart.setEnabled(false); } SwingUtilities.updateComponentTreeUI(getRootPane()); } catch (Exception ex) { ex.printStackTrace(); } } private void enableTheme() { acryl.setEnabled(true); hifi.setEnabled(true); aero.setEnabled(true); aluminium.setEnabled(true); bernstein.setEnabled(true); fast.setEnabled(true); graphite.setEnabled(true); luna.setEnabled(true); mcwin.setEnabled(true); noire.setEnabled(true); smart.setEnabled(true); } public static void main(String []ar) { try { UIManager.setLookAndFeel("com.jtattoo.plaf.acryl.AcrylLookAndFeel"); } catch (Exception e) { e.printStackTrace(); } new DiscussionBoard(); } } What’s the problem here? why its not getting updated? There is a demo application here which is exactly doing what i want but i cant get a clear idea of it.

    Read the article

  • Linux DNS Multi tenant

    - by spicyramen
    I need to setup a multi-tenant DNS solution in Linux DNS Server. Currently I serve multiple companies: Company ABC, Company XYZ, etc... I need to create a) Forwarder zone b) Reverse Forward Zone. I can easily create a Forward Zone with domain abc.com The challenge I have is that each of my customer components share the same IP address. Hence If I create the Reverse Forward Zone I end up with something like this: abc.com 1.1.1.1 host.abc.com xyz.com 1.1.1.1 host.xyz.com If I perform a reverse lookup on host.abc.com it works fine...but if I do a reverse lookup on 1.1.1.1 I get a load balance response of: attempt: host.abc.com attempt: host.xyz.com attempt: host.abc.com Any ideas? I want to add logic to the DNS configuration to handle DNS reverse lookup based on source machine and respond with right hostname. Workaround: Create multiple DNS but this is not scalable.

    Read the article

  • Which CPU for SQL Server machine (Xeon, i5, i7, AMD Phenom)?

    - by Tony_Henrich
    I am going to build a full height server machine to be used for SQL Server 2008 64bit. I have $400 to spend for a CPU. Which CPU should I get among i5, i7, Xeon and Phenom in terms of performance. There are so many options and I am out of touch with the latest stuff. All I know I want something fast and works with DDR3 fast memory and works with some kind of fast system bus. I don't care about overclocking, 3D & gfx benchmarks. The machine is not used for games and gfx apps. Any recommendations?

    Read the article

  • Wireless clients have no route to ethernet clients in OpenWrt router

    - by superjoe30
    I'm using OpenWrt Kamikaze 8.09 on a Linksys WRT54g v1.1 router. I just flashed it with default settings and got everything working, except my wireless laptop cannot ping my desktop which is wired to the router. What can I do to fix this? (My desktop can ping other desktops wired to the router) My routing table: config 'defaults' option 'syn_flood' '1' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'lan' option 'input' 'ACCEPT' option 'output' 'ACCEPT' option 'forward' 'REJECT' config 'zone' option 'name' 'wan' option 'input' 'REJECT' option 'output' 'ACCEPT' option 'forward' 'REJECT' option 'masq' '1' config 'forwarding' option 'src' 'lan' option 'dest' 'wan' option 'mtu_fix' '1' config 'redirect' option 'src' 'wan' option '_name' 'ssh' option 'proto' 'tcp' option 'src_dport' '22' option 'dest_ip' '192.168.1.100' option 'dest_port' '22' config 'redirect' option 'src' 'wan' option '_name' 'http' option 'proto' 'tcp' option 'src_dport' '8888' option 'dest_ip' '192.168.1.100' option 'dest_port' '8888'

    Read the article

  • Fedora12, XP and connection sharing via iptables

    - by Paul L
    Just a quick question ( I Hope ) To find out if what I'm trying is even possible. I am trying to share internet connection with Fedora12 as default gateway and XP machine hooked up via NIC using iptables commands as shown in Mark Sobell's book 'A Practical Guide To Fedora And Red Hat Enterprise Linux' These are the commands as placed in /etc/rc.local iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT iptables -A FORWARD -j LOG iptables -t NAT -A POSTROUTING -o eth1 -j MASQUERADE I did flip the in and out parameters to match my NIC configuration ( as opposed to example from book ) but other than that followed example. One thing to note is that Sobell did not mention whether this should work with mix of Linux and XP. One other note ( maybe meaningless ) is that I do have samba working between the two machines. Thanks for any insights anyone might have. PL

    Read the article

  • Gre tunnel Linux Cisco

    - by mezgani
    I've created a GRE tunnel between LAN A and LAN B. LAN A is behind a router, and LAN B is behind a Linux box and this box has a pppoe interface. When i do tcpdump on Linux box i see that the traffic is routerd to Linux box (tunnel end), so my need is routing the tunnel traffic to internet. I've added these rules to my iptables script, and i stay unable to connect to internet from LAN A Permitting Linux to act as router (necessary to forward packets) echo "1" /proc/sys/net/ipv4/ip_forward iptables -A INPUT -p 47 -j ACCEPT iptables -A FORWARD -i ppp0 -j ACCEPT iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -t nat -A POSTROUTING -o gre0 -j MASEQUARADE What i've forgot to set in this case?

    Read the article

  • Question about Domain Forwarding [beginner]

    - by Jack W-H
    Hello folks Just a quick beginner's question here. I have a webapp located at domainxyz.com, and it generates short URLs for long posts automatically - so rather than visit domainxyz.com/reallylongpostnamehere I can just type domainxyz.com/a5c and be taken there automatically. However, I've bought a shorter domain name - short.com - and I want to be able to visit short.com/a5c and be redirected (or forwarded) to domainxyz.com/a5c. Or short.com/7f0 -- domainxyz.com/7f0. This way, although it seems a tad illogical it saves me setting up another hosting account on short.com to deal with the URL shortening. Is this possible? I realise you can forward domains, but, can you forward domains AND forward the URL segments? Thanks! Jack

    Read the article

  • Postfix sends to original recipient name instead of alias name

    - by user141742
    I have setup Postfix as part of my ISPConfig implementation. It should just forward all mail. Clients should be able to define a new alias and receive mail on a different e-mail address, using ISPConfig. Example: A mail sent to [email protected] on my ISPConfig server should be forwarded to external mailbox [email protected] This works fine but one important thing. When opening the mailbox for [email protected] I see the mail with the original sender name, and the original recipient name, i.e. [email protected] I have tried the forward function and the send copy function on a mailbox in ISPConfig. Both cases show the original recipient [email protected] instead of the final recipient [email protected], as it would when I manually forward an e-mail. Can this be achieved without having to maintain a list for each entry? Thanks for looking into this. M.

    Read the article

  • MD3200i Slow Performance and Queue Depth

    - by Caleb_S
    Read performance on our SAN is slow under certain workloads. When we compare this to some local storage, we find the local storage performing 2x as fast. The SAN performs well with a high Queue Depth, and poorly with a low queue depth. However, the local storage performs well with a low Queue Depth. I'd like to know the reason for this occurring and find out what the specific limiting factor is in this situation. MD3200i iSCSI SAN ($15,000) 6 x 600GB 15k SAS RAID5 6 x 2TB 7.2k NLS RAID5 XCOPY /j Benchmark: (Slow) 15k Array - 71MB/s (Queue Depth 1) 7.2k Array- 71MB/s (Queue Depth 1) Robycopy /MT:32 Benchmark: (Fast) 15k Array - 171MB/s (Queue Depth ~12) 7.2k Array- 128MB/s (Queue Depth ~12) , , Read Performance on a Local controller is fast under the workload the SAN is slow at. , HighPoint 2230 RAID Controller ($600) 4 x 1TB 7.2k SATA RAID5 XCOPY /j Benchmark: 7.2k Array - 145MB/s (Queue Depth 1) (appears to max out the SATA bus)

    Read the article

  • Attempting to caue packet loss with netem doesn't work - possibly because of NAT (but delay does work)

    - by tomdee
    I have traffic from a WIFI access point routed via an Ubuntu box. I have two network interfaces which are NATed *filter :INPUT ACCEPT [11:690] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [37:6224] -A FORWARD -s 192.168.2.0/24 -i eth1 -o eth0 -m conntrack --ctstate NEW -j ACCEPT -A FORWARD -m conntrack --ctstate RELATED,ESTABLISHED -j ACCEPT COMMIT # Completed on Thu Mar 15 13:37:21 2012 # Generated by iptables-save v1.4.10 on Thu Mar 15 13:37:21 2012 *nat :PREROUTING ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -j MASQUERADE COMMIT If I run a ping app on an Android device connected to the WIFI network I can happily ping google. If I use netem to introduce some delay tc qdisc change dev eth0 root netem delay 100ms I can clearly see pings taking longer. If I use netem to introduce some packet loss tc qdisc change dev ifb0 root netem loss 50% then I see no change. Packet loss does work fine for locally generated traffic, just not for traffic coming in over the network that's being NATed. Any ideas how to sort this out?

    Read the article

  • Network Drive Via Ethernet Port for Speed?

    - by Yar
    I have a Macbook with Firewire 400 and USB 2.0, so the only way I can get fast external storage is through the Ethernet port. A really fast firewire 800 drive on ANOTHER computer is actually much faster than the built-in drive (according to XBench). So I thought I would try to go one better and buy an ethernet-ready drive. I bought a Seagate GoFlex™ Home Network Storage System, and it seems like the only way to get it to work is to plug it into a router. Can this drive be used without a router (i.e., direct to computer)? Are there any drives that can be plugged directly into the ethernet port for fast access? I don't want the drive on my router: I want it on my computer. Ideally I'd need 7200rpm or faster, too... Update: Just chatted with Seagate and they said that this particular drive will not work that way. Will any others?

    Read the article

  • PostgreSQL disaster recovery options

    - by Alex
    My customer has quite a large (the total "data" folder size is 200G) PostgreSQL database and we are working on a disaster recovery plan. We have identified three different types of disasters so far: hardware outage, too much load and unintentional data loss due to erroneously executed bad migration (like DELETE or ALTER TABLE DROP COLUMN). First two types seem to be easy to mitigate but we can't elaborate a good mitigation plan for the third type. I proposed to use ZFS and frequent (hourly) snapshots but "ZFS" means "OpenIndiana" these days and our Ops engineers do not have much expertise in it, so using OpenIndiana imposes another risk. Colleagues try to convince me that restoring from PostgreSQL PITR backup can be as fast as restoring from a ZFS snapshot but I highly doubt that replaying, say, 50G of archived WALs can be considered "fast". What other options are we missing? Is ZFS an only viable alternative? Can we get a fast Pg DB restore time in the Linux environment?

    Read the article

  • X11 forwarding from one server to other

    - by n3oblit7
    I have a setup where I need to forward X11 from my local machine (laptop) to a Virtual machine. The server hosting this VM cannot be reached directly from my laptop. I need to first login to a gateway and from this gateway, I can access the VM. How can I forward X11 from my laptop to this VM? I have tried following but these do not work: [laptop # ] ssh -X [gateway] [gateway # ] ssh -X [VM] [laptop # ] ssh -tX [gateway] ssh -X [VM] I could forward X11 only till the gateway. (DISPLAY variable gets set on gateway)

    Read the article

  • Can I pass HTTPS traffic from one port to another?

    - by Kit Sunde
    I'm doing a proxy_pass in nginx on port 80 to 8000 on my remote server, and then a port forward from 8000 to 80 from the remote to my localhost. This works great, but I'd also like to do it with https but it seems like nginx needs a valid cert to pass the traffic on. Is there a way for my remote server to simply forward the trafic from port 443 to say 8443 (and then I'll forward remote 8443 to local 443). Then terminate ssl on my development machine instead instead of needing to do it on the remote server? My remote runs ubuntu and my localhost runs osx.

    Read the article

  • X11 forwarding from one server to other

    - by n3oblit7
    I have a setup where I need to forward X11 from my local machine (laptop) to a Virtual machine. The server hosting this VM cannot be reached directly from my laptop. I need to first login to a gateway and from this gateway, I can access the VM. How can I forward X11 from my laptop to this VM? I have tried following but these do not work: [laptop # ] ssh -X [gateway] [gateway # ] ssh -X [VM] [laptop # ] ssh -tX [gateway] ssh -X [VM] I could forward X11 only till the gateway. (DISPLAY variable gets set on gateway)

    Read the article

  • Reverse Proxy Server SSL?

    - by valveLondon
    Context We currently have an Apache web server in the DMZ set up as a reverse proxy and load balancer for two machines running Windows Server 2008 (IIS) inside. The Apache server has a genuine SSL certificate and serves up both http and https, however, the balancer members in the load balancing section are set to: BalancerMember {https://server1} and {https://server2}. The IIS web servers have self-signed certificates in order to respond to the https requests. My question: Do we need to forward any requests from Apache (in the DMZ) to the inside using SSL? e.g can the reverse proxy forward the requests using HTTP? and if so, why would I choose to forward them with SSL? (how secure is the http line between the dmz and the inside); In other words, can I totally disable SSL on my inside web servers?

    Read the article

  • Can't get port forwarding to work on Ubuntu

    - by Znarkus
    I'm using my home server as NAT/router, which works well. But now I'm trying to forward port 3478, which I can't get to work. eth0 = public interface eth1 = private network $ cat /proc/sys/net/ipv4/conf/eth0/forwarding 1 $ cat /proc/sys/net/ipv4/conf/eth1/forwarding 1 Then to forward port 3478 to 10.0.0.7, I read somewhere that I should run iptables -t nat -A PREROUTING -p tcp -i eth0 --dport 3478 -j DNAT --to-destination 10.0.0.7:3478 iptables -A FORWARD -p tcp -d 10.0.0.7 --dport 3478 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT I also ran ufw allow 3478 But testing port 3478 with http://www.canyouseeme.org/ doesn't work. Any idea what I have done wrong?

    Read the article

  • Why are perfectly legitamate pages on my website registering in google Webmasters as 404?

    - by christian
    I have seen this question asked several times here, but never clearly answered. I suspect it has something to do with my .htaccess file: # BEGIN WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.php [L] </IfModule> # END WordPress <IfModule mod_rewrite.c> RewriteEngine On RewriteRule ^moreinfo/(.*)$ http://www.kgstiles.com/moreinfo$1 [R=301] RewriteRule ^healthsolutions/(.*)$ http://www.kgstiles.com/healthsolutions$1 [R=301] RewriteRule ^(.*)\.html$ $1/ [R=301] RewriteRule ^(.*)\.htm$ $1/ [R=301] </IfModule> when I check the url without a forward slash at the end, it registers as 404 (even though it renders fine in a browser), but when I write it without the forward slash at the end, it renders 200 OK, but if I try to take off the forward slash with the htaccess file, the browser gives me a 310 error (too many redirects) you can see the 404 and 310 with this url: http://www.kgstiles.com/pureplantessentials.html which redirects to http://www.kgstiles.com/pureplantessentials/ (which is a 404), so what is a solution and why might this be registering as a 404? Any Help is appreciated! (I'm using wordpress btw)

    Read the article

  • SQLAuthority News – Microsoft SQL Server 2008 R2 – PowerPivot for Microsoft Excel 2010

    - by pinaldave
    Microsoft has really and truly created some buzz for PowerPivot. I have been asked to show the demo of Powerpivot in recent time even when I am doing relational database training. Attached is the few details where everyone can download PowerPivot and use the same. Microsoft SQL Server 2008 R2 – PowerPivot for Microsoft Excel 2010 – RTM Microsoft® PowerPivot for Microsoft® Excel 2010 provides ground-breaking technology, such as fast manipulation of large data sets (often millions of rows), streamlined integration of data, and the ability to effortlessly share your analysis through Microsoft® SharePoint 2010. Microsoft PowerPivot for Excel 2010 Samples Microsoft® PowerPivot for Microsoft® Excel 2010 provides ground-breaking technology, such as fast manipulation of large data sets (often millions of rows), streamlined integration of data, and the ability to effortlessly share your analysis through Microsoft® SharePoint 2010. Download examples of the types of reports you can create. Microsoft PowerPivot for Excel 2010 Data Analysis Expressions Sample version 1.0 Microsoft® PowerPivot for Microsoft® Excel 2010 provides ground-breaking technology, such as fast manipulation of large data sets (often millions of rows), streamlined integration of data, and the ability to effortlessly share your analysis through Microsoft® SharePoint 2010. Download this PowerPivot workbook to learn more about DAX calculations. Note: The brief description below the download link is taken from respective download page. Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: SQL, SQL Authority, SQL Documentation, SQL Download, SQL Query, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • enable email on Godaddy when using Zerigo on Heroku hosted app

    - by joelmaranhao
    A little recap of what I have done ... and then my questions Q1, Q2 and Q3 1 - I developed a RoR app that I deployed on Heroku. biowatts.heroku.com 2 - I bought a domain name at GoDaddy: biowattsonline.com 3 - I am using Zerigo addon as for the DNS heroku addons:add custom_domains heroku addons:add zerigo_dns:basic 4 - Added my domains in Heroku heroku domains:add biowattsonline.com heroku domains:add www.biowattsonline.com and subdomains heroku domains:add calculator.biowattsonline.com Q1: Where do we configure the forward to http://biowattsonline.com/biogas_calculator ? 5 - Configured GoDaddy adding the Zerigo domains In the Nameservers section a.ns.zerigo.net b.ns.zerigo.net c.ns.zerigo.net d.ns.zerigo.net e.ns.zerigo.net The GoDaddy DNS section is empty: "Not hosted here" Ok this works all fine ... http://biowattsonline.com is correctly found 6 - Subdomain forward I want calculator.biowattsonline.com to be forwarded to biowattsonline.com/biogas_calculator Q2: So I created the forward in GoDaddy ... but is that correct? 7 - GoDaddy email Q3: I have one free email account with go GoDaddy, only now that I am using Zerigo I don't know how configure GoDaddy to make it work again?... because it work with the default values Any ideason Q1, Q2 and Q3? Thanks, Joel

    Read the article

< Previous Page | 45 46 47 48 49 50 51 52 53 54 55 56  | Next Page >