Search Results

Search found 14974 results on 599 pages for 'old games'.

Page 490/599 | < Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >

• SSD as primary or secondary drive on a small Linux server?

  - by Alex Martelli

  I'm pensioning off my 10-years-old home server and replacing it with an Ubuntu 10.04 box. The two storage devices are a Western Digital Caviar Green 2.0TB HD and an Intel X25-M 34nm Gen 2 80GB SATA II 2.5inch SSD (the box has 8GB RAM and an i5 750, if it matters). I don't care much about boot times (since I don't plan to reboot all that often;-); the main frequent, performance-demanding task will be (re)building large open source C or C++ software packages from sources (as an open source contributor, I do that often). So, I thought I'd keep the SSD as the secondary drive and the HD as the primary one, using the SSD mostly for the files that can otherwise demand a lot of seeking (esp. in a parallel make). However, the friendly vendor (perhaps more experienced in Windows systems than in Linux ones) thinks the "normal" way to configure the machine would be with the SSD as the primary drive. I'm pretty rusty on configuring and tuning systems, so, I thought I'd better double check on SuperUser... thanks in advance for advice about this choice!

  Read the article

• 'The rpc server is unavailable' or 'access is denied' error when using Remote desktop Services Manager on Windows 7 (but mstsc.exe works!)

  - by tbone

  I am trying to connect to a Windows XP workstation from a Windows 7 Ultimate workstation using Remote Desktop Services Manager. I am able to do a Remote Desktop (mstsc.exe) session from the Win7 machine to the WinXP machine with no problem at all. When running the Remote Desktops Admin (tsmmc.msc) too on a Windows XP box, I can also connect with no problem. However, when I use the new Remote Desktop Services Manager on Windows 7 and try to connect, I get the error: "The rpc server is unavailable" What could cause this? Has there been some fundamental change in Remote Desktop Services Manager, does it connect in a different way somehow? Update #1 Turned off firewall on the Windows XP box and the "The rpc server is unavailable" error went away; so RDSM seems to be using an entirely new port/connection/service compared to mstsc.exe or the old Remote Desktops Admin tool. Now... after disabling the firewall, I get a new error: Access is Denied. After doing some googling, I found some articles discussing this; basically, the error is very misleading - the actual problem is, if either side of the connection has dual monitors, and they are not both Win7 Ultimate, then you cannot connect using Remote Desktop Services Manager...the reason is, by default it uses the /multimon switch, and this switch requires a certain level of Windows license - and, there seems to be no way of changing this default (if anyone knows of a way to change this default, please post an answer or comment!). Nice going Microsoft. http://social.technet.microsoft.com/Forums/en-US/windowsserver2008r2rds/thread/4d06278f-e0f4-4f8e-a8e1-3697ee967ef4 http://www.experts-exchange.com/OS/Microsoft_Operating_Systems/Windows/Windows_7/Q_26225743.html

  Read the article

• Is there an objective way to measure slowness of PC/WINDOWS?

  - by ekms

  We've a lot of users that usually complain about that his PC is "slow". (we use win XP). We usually check startup programs, virus, fragmentation, disk health and common problems that causes slowness (Symantec AV drops disk to 1mb/s , or a seagate HD firmware error in certain models), but in those cases the slowness is pretty evident. In other hand, the most common is the user complaining about his pc but for us looks OK, even in 6 years old desktops. People sometimes even complains about his new quad core desktops speed!!! So, we are asking if there's a way to OBJECTIVELY check that a computer didn't dropped its performance, compared with similar ones o previous measures, specially for work use (I don't think that 3dmark benchmark o similar may help). The only thing that I found that was useful is HDTune, but it only check hard disk performance. Basically, what we want is something that enable us to say to our users "see? your PC is as slow as was three years ago! stop complaining! Is all in your head!"

  Read the article

• Drive letter not appearing after heat-related crash

  - by NickAldwin

  I recently had my old PC (has 3 physical hard drives partitioned into 6 partitions) off while on vacation. When I came back, I turned it on. I hadn't realized the room was warmer than it usually is due to hot weather while I was away. The computer was extremely slow to start up, then it crashed. When i rebooted, it got halfway through chkdsk on one of the non-system partitions, then crashed again. I opened it up and felt the hard drives and immediately shut down the computer and moved it to my basement to cool down because it was so hot. I left it there for a length of time while I reinstalled the A/C. I have now turned it on again. It is working fine, and every drive except for the one with the partition that was being checked has appeared in Windows. I scheduled chkdsk for all of the other partitions anyway, just in case, but I'm worried about that drive. I'm pretty sure the drive itself hasn't broken but that crashing in the middle of a chkdsk repair may have corrupted the data. What would you do in this situation? Most of the data on that drive was backed up, so it's not a huge deal if I lost it, but I'd like to get it back if I could. I also would love to regain usability of the drive, even if I have to wipe it -- but that's a last-resort sort of thing. What do you suggest I do?

  Read the article

• Get the Windows Scheduler's Location Or Code?

  - by Ram

  Today i got a task to find the scheduler that is running once in a month, actually I have to change its running time period to once a week. I have searched for it in the Windows scheduled tasks, but i didn't find it. It is sending a mail containing a link. Now i am not confused about this where else can i find it. As the place i know where the scheduler can be, has already been checked by me. Can someone suggest me where else can i search for this scheduler? As per the previous developer's comment "It is a normal Windows method of scheduling tasks" UPDATE Actually the task is running after a month periodically. As per my knowledge it could be a "Windows Task Schedule" or "Windows Service" created by the old developer. Now as the previous developer is not available and i do not have any documentation.. i need to change the time period from month to weakly. I have checked in the "Task Schedules" on the server and checked the services running ob the server and was unable to find the "Scheduler". now i have two questions: is there any other approach by using that i can schedule an automated email periodically. any idea to find this.

  Read the article

• Exchange emails not delivering for one user

  - by Cylindric

  We have an Exchange infrastructure going through a migration from 2003 SP2 (call it ExOld) to 2010 (ExNew). All users are now on the new server, but mail is still being directed to ExOld until testing is complete. ExNew sends emails directly to the internet. For one particular user, emails don't seem to be being reliably delivered, but the odd thing is that it's not all emails. I can see external emails in his inbox. If I send an internal email it works fine. If I send an email from Gmail to him it doesn't get through. If I telnet from outside to ExOld I can send an email to him. If I telnet from outside to ExNew I can send an email to him. This is a transcript that results in a successful send: 220 ExOldName Microsoft ESMTP MAIL Service, Version: 6.0.3790.4675 ready at Mon, 22 Oct 2012 10:55:26 +0100 EHLO test.com 500 5.3.3 Unrecognized command EHLO test.com 250-ExOldFQDN Hello [MyTestExternalIp] 250-TURN 250-SIZE 250-ETRN 250-PIPELINING 250-DSN 250-ENHANCEDSTATUSCODES 250-8bitmime 250-BINARYMIME 250-CHUNKING 250-VRFY 250-X-EXPS GSSAPI NTLM LOGIN 250-X-EXPS=LOGIN 250-AUTH GSSAPI NTLM LOGIN 250-AUTH=LOGIN 250-X-LINK2STATE 250-XEXCH50 250 OK MAIL FROM:[email protected] 250 2.1.0 [email protected] OK RCPT TO:[email protected] notify=success,failure 250 2.1.5 [email protected] DATA 354 Start mail input; end with . Subject:Test 1056 Test 10:56 . 250 2.6.0 Queued mail for delivery quit 221 2.0.0 ExOldFQDN Service closing transmission channel Emails go through Symantec Cloud, but their "Track and Trace" shows the messages going through, with a "delivered ok" log entry. 2012-10-22 09:19:56 Connection from: 209.85.212.171 (mail-wi0-f171.google.com) 2012-10-22 09:19:56 Sending server HELO string:mail-wi0-f171.google.com 2012-10-22 09:19:56 Message id:CAE5-_4hzGpY2kXFbzxu7gzEUSj5BAvi+BB5q1Gjb6UUOXOWT3g@mail.gmail.com 2012-10-22 09:19:56 Message reference: 135089759500000177171130001194006 2012-10-22 09:19:56 Sender: [email protected] 2012-10-22 09:19:56 Recipient: [email protected] 2012-10-22 09:20:26 SMTP Status: OK 2012-10-22 09:19:56 Delivery attempt #1 (final) 2012-10-22 09:19:56 Recipient server: ExOldIP (ExOldIP) 2012-10-22 09:19:56 Response: 250 2.6.0 Queued mail for delivery I'm not sure where to look on the old (or new) server for information as to where the mails are ending up.

  Read the article

• How to Upgrade PHP 5.2 to 5.3 on Windows Plesk Panel 8.2

  - by Jagat Sheth

  I need to upgrade my server PHP version becasue of Wordpress New version not support PHP 5.2. On My server windows 2003 stansard edition x64 with SP1 installed, IIS 6.0, MySQL 4.1, Plesk Panel 8.2. I have follow listed steps on plesk KB. http://kb.parallels.com/6670 How to update PHP 5 on a Windows server with Parallels Plesk Control Panel 8.x and 9.x installed. In order to upgrade PHP 5 to the necessary version (other than shipped with Parallels Plesk), please perform the following steps: Stop Plesk services (‘Control Panel’ and all that are included in the ‘Plesk Run-Time’ section) Rename folder %plesk_dir%\Additional\PleskPHP5 to the orig_PleskPHP5 Create a new folder %plesk_dir%\Additional\PleskPHP5 Download necessary version of PHP, unzip its content, and copy it to the newly created folder PleskPHP5 Copy the file php.ini from the old folder orig_PleskPHP5 to the new one Make sure the permissions are inherited Start Plesk services Click the "Refresh" button in the Components Management section in Parallels Plesk Panel and check if you can see the new PHP version there After follow steps when I open a PHP info it shows me specified module could not be found. If anybody know solution Kindly help me is highly priority. I am very thankful if any one help me to solve this ASAP. Thanks and regards, Jagat Sheth

  Read the article

• Access node.js local server though mobile via same shared wifi

  - by laggingreflex

  EDIT: I was stuck in this situation before but then it was Apache-related But this time I'm using NodeJS, so the old answer doesn't help. I'm running apache a NodeJS webserver (on port 80) on Windows 7. I want to access the webserver through my mobile which shares the wifi router with my pc locally. http://localhost works from PC. But I can't access http://192.168.1.4 from either my phone or even my computer. ipconfig /all on my computer lists my ip address as 192.168.1.4 Wireless LAN adapter Wireless Network Connection: IPv4 Address. . . . . . . . . . . : 192.168.1.4(Preferred) I can ping my phone's (internal) ip address [192.168.1.5] from PC and vice-versa, I can ping my PC [192.168.1.4] from my phone. So why can't I access http://192.168.1.4 from my phone? (or PC) Firewall is off.

  Read the article

• Cannot write to directory after taking ownership

  - by jeff charles

  I had a directory on an internal hard-drive that was created in an old Windows 7 install. After re-installing my operating system, when I try to create a new directory inside that directory, I get an Access Denied message. This isn't a protected directory, just a random directory I created at the drive root (that drive was not the C drive in either install). I tried to take ownership by opening folder properties, going to the Security tab, clicking on Advanced, going to Owner tab, clicking on Edit, selecting my user account, checking Replace owner on subcontainers and objects, and clicking Apply. There were no error messages and I closed the dialogs. I rebooted, checked the owner on that folder and a couple subfolders and it appears to be set correctly. I am still getting an Access Denied message however when trying to create a directory in it. I've also tried using attrib -R . to remove any possible readonly attribute inside the directory in an admin command prompt but am still unable to create a directory using a non-admin prompt (it does work in an admin prompt). Is there anything I can do to get write access to that folder and it's subcontents in a non-elevated context without disabling UAC?

  Read the article

• Centos repository packages vs latest developer release

  - by fran

  I have started to run a personal server using CentOS and I have noticed that many packages that are available to install from repository are old compared with the latest release from the developer. I know that installing packages from repository is very easy and I guess that the supplied versions are stable and prepared to work without any trouble, but I still find odd having so much software that lags behind the current version. It's my first time with linux and I don't know what is the "normal" thing, should I stick to whatever version the repository supplies, or try to get the latest from the developer? To be more precisely, the repository supplies the apache httpd web server with version 2.2, I wanted to update to 2.4, so I started removing apache and its dependencies packages that come with centos to use the latest ones, but when I was about to remove pcre v6 to replace it with v8, i found out that 132 installed packages depend on it and probably it is not a good idea to remove it, so that made me think twice about getting the latest software instead of using the packages supplied by the official repositories. Should I leave things as they are instead of going on an upgrade rampage? Thanks

  Read the article

• Can't find partition tab in disk utility osX ver. 10.6.8

  - by John W

  I just got a used Mac Book Pro. I created a new admin account and deleted the old one as well as one other user. This is an older late 2007 MBP... the osX upgrade to 10.6.8 was just performed. My Macintosh HD is showing up as Partition 2. I ran disk utility (not from install disk), but there was no partition tab. I have a 160GB drive with only 53GB of space left on it. Since I am the only user and have no files on the laptop yet, I don't understand why there is so little space left. Surely the OS can't use up over 100GB. I wanted to run disk utility to see if there were any recovery partitions or other partition left over from the previous owner that could be erased to make room for expanding the main partition. Unfortunately, there is no partition tab in disk utility. The documentation I have found on line states that this version of osX includes that utility. The osX disks I have are for an older version so I wasn't sure if they would be of any use in solving this problem. Also, I was afraid if using the disks, would I lose the little bit of data/apps that I have assembled. I would rather not do a fresh install and have to do all the updates again to achieve this. The previous owner had some apps that I don't want to lose as I would have to pay handsomely to get them back. Simply, if all the previous users data is backed up on here after deleting user is still taking up space on a recovery partition (that I can't see)... I need to locate it erase it and expand the primary partition to re-aquire disk space for my files. I am new to Mac, so please be as descriptive as possible. Thanks.

  Read the article

• How can I make a copy of a printer in Win7?

  - by hawbsl

  Has anyone been able to copy an existing printer in Win7? I know that we were able to do this in XP (not as a direct copy/paste, but by installing the printer twice) but in Win7 it doesn't seem to be possible. Googling the answer is hopeless because searching for "copy printer" or "duplicate printer" you get a bunch of posts about "printer copiers" or people complaining about duplicate printers getting created in the background (precisely what I'd like to be able to do) It'd be good to know how to do it in general, but if it depends on the printer type, then in our case we are trying to make a copy of an HP Laserjet. Tried installing from the CD - but the CD is too old for Win7 Tried installing via Add Printer and that seems to install the printer but it's marked with an error. Tried installing via the .exe installer from the HP site and that does result in a successful printer being installed, but it won't let you install the same printer twice (stalls on the "insert USB cable now" step - simply won't enable the greyed out "Next" button). The reason this is required is so that we can print to one to the feeder and to the tray separately.

  Read the article

• Proper approach to debug PC startup problems (POST)

  - by saurabhj

  My CPU was heating up to around 65 deg C and last time this had happened (about a year ago), I got thermal paste put between the CPU and heat sink and this managed to get it down to about 45 - 50 degrees. This time, I got some thermal paste and put it myself. However, my PC is not showing the POST display and not starting up. This is what happens LEDs light up HDDs spin Mouse is getting power All fans including the processor fan starts No display on monitor No diagnostic beep sounds (no sounds at all) What I have tried Removing everything including RAM, HDD, PCI cards, AGP card Boot up machine No changes from first state. What steps can I take to figure out where the problem lies? Note (might be important) When I removed the heat sink, the processor came out with it (it was stuck to it inspite of the processor latch on) Had to pry it separate with a screw-driver. Configuration Pentium 4, 2.8 Ghz with HT (very old, I know) Original Intel Mobo with onboard sound and graphics (GB series) 2x512 Mb DDR-RAM 2 SATA disks (320 Gigs / 250 gigs) DVD Writer Creative Sound Card Network card Any help would be appreciated. Thanks!

  Read the article

• computer fails to boot during/after POST for five or six boots, then works

  - by N13

  For the last few days, my computer has had issues booting. I've seen two different behaviors: The screen displays the graphics card information, then begins to list the RAM, hard drives, etc. At different points in this process (after the graphics info), the computer shuts off. After five or six attempts, it then boots normally. In roughly the same time frame, the computer freezes, and fails to boot. I think it boots successfully on the next attempt. I've also noticed that in some instances, the computer freezes on shutdown. It gets right to the point where it should shut off, but doesn't. I recently combined the best parts of two different machines into this one. I'm booting to GRUB, with Ubuntu 12.04, Linux Mint 11 and Windows Vista (unfortunately) as my OS options. It has an Enermax Modu82+ 525W power supply, and I've used an online calculator to determine that my load shouldn't exceed 400W. I even unplugged a hard drive, but that didn't help. I found the latest BIOS, patched it and checked the settings, but that didn't fix it. I'm fairly certain this issue didn't exist at first, but might have started when the power at my new apartment dropped for a second. The machine is plugged into a surge protector strip, but it's old and I've heard they lose effectiveness with age. Is a power dip as damaging as a spike? If something were damaged, why would it boot successfully after five or six attempts? It's almost like the BIOS or PSU need to be primed. The trouble with debugging is that there seems to be a "grace period" after shutdown where the issue doesn't present itself again. What should I try next?

  Read the article

• Why is my rsync so slow compared to pure cp or even scp?

  - by nfm

  I'm transfering the files from Linux to Windows 7 via a mounted share (the share is mounted from Windows on Linux).. I'm copying lots of data (i.e. nearly a TB) from the old to the new machine within my LAN. I'm unfortunate enough already that I only have 100MBit. Naturally I blindly used rsync but already wondered after a day why it feels so slow. Enabling the progress meter showed my a transfer rate of about 2MBit/s . So I took a reasonable big file (800MB) and tracked the transfer timing: cp : 05:33 scp (*): 06:33 rsync : 21:51 *) scp via localhost to the same Linux machine directly onto the share; completely useless but provided a progress meter The tests were as simple as (cp|scp|rsync) <source> <destination> No special arguments except host/port for scp. I even tried the -W switch for rsync but cancelled after ten minutes. rsync is 3.0.3 running on Lenny. To be able to interrupt the copy process anytime and resume lead me to rsync, but now I think I seriously need to reconsider this requirement. How's such a big difference possible?

  Read the article

• Combine multiple rows into one

  - by Jim

  I am trying to combine multiple rows of data into one. Column A contains the value on which the groupings will be based -- rows whose Column A values match will be combined into one row. My range extends from column A through X so I need a matching row of data to start in column Y. Example: +--------------+ ¦ 1001 ¦ A ¦ C ¦ ¦ 1001 ¦ B ¦ D ¦ ¦ 1002 ¦ A ¦ E ¦ ¦ 1002 ¦ B ¦ F ¦ ¦ 1002 ¦ C ¦ G ¦ +--------------+ Desired Result: +------------------------------+ ¦ 1001 ¦ A ¦ C ¦ B ¦ D ¦ ¦ ¦ ¦ 1002 ¦ A ¦ E ¦ B ¦ F ¦ C ¦ G ¦ +------------------------------+ The VBA code I am currently using is not taking the entire contents of the matched row. It is only taking the data in the 2nd column and moving it up. VBA Code: Sub Mergeitems() Dim cl As Range Dim rw As Range Set rw = ActiveCell Do While rw <> "" ' for each row in data set ' find first empty cell on row Set cl = rw.Offset(0, 1) Do While cl <> "" Set cl = cl.Offset(0, 1) Loop ' if next row needs to be processed... Do While rw = rw.Offset(1, 0) cl = rw.Offset(1, 1) ' move the data Set cl = cl.Offset(0, 1) ' update pointer to next blank cell rw.Offset(1, 0).EntireRow.Delete xlShiftUp ' delete old data Loop ' next row Set rw = rw.Offset(1, 0) Loop End Sub

  Read the article

• Simple Distributed Disconnected way to sync a directory

  - by Rory

  I want to start regularly backup my home directory on my ubuntu laptop, machine X. Suppose I have access to 2 different remote (linux) servers that I can backup to, machines A & B. Machine X will be the master, and should be synced to A and B. I could just regularly run rsync from X to A and then from X to B. That's all I need. However I'm curious if there's a more bandwidth effecient, and hence faster way to do it. Assuming X is going to be on residential style broadband lines, and since I don't want to soak up the bandwidth, I would limit the transfer from X. A and B will be on all the time, however X, will not be, so I'd also like to reduce the amount of time that X is transfering, potentially allowing A and B to spend more time transfering. Also, X won't be connected all the time. What's the best way to do this? rsync from X to A, then from A to B? Timing that right could be troublesome. I don't want to keep old files around, so if I was to rsync, then the --del option would be used. Could that mean something might get tranfered from A to B, then deleted from B, then transfered from A to B again? That's suboptimal. I know there are fancy distributed filesystems like gluster, but I think that's overkill in this case, and might not fit with the disconnected nature.

  Read the article

• VMware Workstation Bridged Network Host UnReachable

  - by user2097818

  VMware Workstation 7 on Win7-64 (Home Premium). I have confirmed this on any guest running on this machine (from winxp to debian). I am using a bridged network connection for my guests (Automatic on VMnet0). All of the network configuration is done with DHCP (including on the host). Problem What I can not do: Ping my host machine from inside any VM. (either shows me "Destination Host Unreachable" or will just timeout) What I CAN do right after power up, with no problems at all. I can connect to the internet from inside the VM I can ping my router from inside the VM I can ping other machines on my network from inside the VM Other machines can ping the VM Other machines can ping the host My host machine can ping the VM (this one is important. read further) Details So I have my router assigned as 192.168.2.1/255.255.255.0, and the router provides the DHCP service (and it seems to be doing so successfully). There are no IP conflicts on the network that I am aware of. All Gateways and Subnet masks are appropriate and matching. My entire workshop is on one single subnet, with one single DHCP server and gateway. There is one method in which I can ping successfully, but it requires an active connection initiated from the host (I start pinging from host to VM). During the period of the active connection, I can successfully ping from VM to host, using explicit IP address. As soon as the host connection is closed, the VM ping starts hanging with the same old messages. My Thoughts This really feels like a firewall problem, but I have turned off all firewalls on host and VM, powered down the network, powered back up, and the problem still persists. And if it was firewall, why would only the IP address associated with bridged VM networks be blocked. I feel as though my host operating system (Win7) is somehow configured incorrectly, or, VMware Workstation is configured incorrectly from the host side. Although I have done my best to put everything in default, I feel like I am missing something silly.

  Read the article

• FreeBSD: problem with Postfix after updating LDAP

  - by Olexandr

  At the server I installed openldap-server, at this computer open-ldap client has already been installed. Version of openldap-client (2.4.16) was older then new openldap-server (2.4.21) and the version of client has updated too. OpenLDAP-client works with postfix on this server and after all updates postfix cann't start again. The error when postfix stop|start is: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix" At the category with libraries is libldap-2.4.so.7, but libldap-2.4.so.6 is removed from the server. When I want to deinstall curently version of openldap-client, system write ===> Deinstalling for net/openldap24-client O.K., but when I start "make install" system write: ===> Installing for openldap-sasl-client-2.4.23 ===> openldap-sasl-client-2.4.23 depends on shared library: sasl2.2 - found ===> Generating temporary packing list ===> Checking if net/openldap24-client already installed ===> An older version of net/openldap24-client is already installed (openldap-client-2.4.21) You may wish to ``make deinstall'' and install this port again by ``make reinstall'' to upgrade it properly. If you really wish to overwrite the old port of net/openldap24-client without deleting it first, set the variable "FORCE_PKG_REGISTER" in your environment or the "make install" command line. *** Error code 1 Stop in /usr/ports/net/openldap24-client. *** Error code 1 Stop in /usr/ports/net/openldap24-client. Updating of ports doesn't help, and postfix writes error: /libexec/ld-elf.so.1: Shared object "libldap-2.4.so.6" not found, required by "postfix"

  Read the article

• Ubuntu 12.04 Very slow especially with Android Studio

  - by Nada

  I have an old laptop with the following specification: Memory: 485 MiB, Processor: Genuine intel CPU T2300 @ 1.66 GHz ×2, OS Type: 32 bit, Disk: 78.1 GB, I installed on it Ubuntu 12.04 LTS and I noticed that the overall system is very slow in responding. I tried to search about that in the internet and I found some articles talking about how to make Ubuntu 12.04 LTS run fast I applied all what they said including download LXDE desktop environment and then nothing different in the system response time. Then I need to develop some android applications so, I download Android Studio (Beta) 0.8.6. The problem became worse than before whenever I tried to open the Android Studio the screen is frozen for some minutes then it took time to download the projects and initialize the work space also, when I tried to move the cursor he is move very slowly. When I tried to run my first application on the AVD it took three hours and still not run yet. I delete the Android Studio and install it again several times, I was trying to solve the problem but still nothing change. Please if you have any suggestions that may help me make my laptop and Android Studio work faster I will appreciate it for you. Thank you in advance.

  Read the article

• Can a OS be copied from one hard drive to another and still boot?

  - by AlexMorley-Finch

  Background My computer gets stuck on the make and model screen after the BIOS screen, aka the Toshiba screen. After some research I've realized that the problem is the hard drive. I'm using an old 250gb model that USED to be used for backup purposes, however I loaded windows 7 ultimate onto it This hard drive has trouble getting up to full RPM therefore cannot boot correctly until its warmed up. meaning that my pc needs to be restarted several times before it boots (once it took my 13 reboots to get my pc on!) From my research its either that, or lack of power supply, and I've tried multiple PSUs. Question I have my OS and all my files on this 250gb HDD... If I were to literally open the explorer, and copy EVERYTHING (including hidden files obviously) from this 250gb, to a spare 500gb I've got knocking about... Will it boot if I just copy everything? I cannot be bothered to load another OS onto my PC so if there is a way I can just copy the existing one over from one HDD to another and have it boot normally. This would be epic! I've heard about HDD cloning software. But before I purchase and/or download this software, I need to know if i can just copy the OS over through the windows explorer

  Read the article

• In which order does Excel process its formulae?

  - by dwwilson66

  I've got a fairly large spreadsheet with major calculations going on, and it's starting to slow down every time a value that's part of a calculated field is modified. I'm in the process of optimizing the file, adding arrays where I can, and seeing where I can shave off a few milliseconds here and there. Let's say there's data in Columns A-H. Column H is set based on relationships between values in Columns A, B and C, which change dynamically from an outside program. Users enter the data in Column F. Formulas in D & E calculate relationships between F & H and H & D, respectively. How does Excel manage formulae in the case, for instance, where they're dependent on data further into the sheet? Will my value in H be available the first time that the formulae in D & E calculate? or, will D & E calculate based on an old value for H, because H's update hasn't happened yet? Are there any efficiencies to be gained by positioning dependencies in particular rows or columns in the speadsheet? Do positions above and left the current position get processed sooner than things below and to the right?

  Read the article

• Can I restore one of my user's profiles in Vista?

  - by Rod

  My youngest daughter uses my 4 year old laptop, which has Windows Vista installed. Somehow she got some Trojan (Vista Internet Security). (I'd love to know how that happened, seeing as how she is a standard user, and I have VIPRE as my AV.) Anyway, I ran a deep anti-virus scan using VIPRE, which identified it. I decided to delete everything that it identified. Now she cannot use anything in her profile. If she tries to bring up the browser, it recycles over and over again a dialog box asking which program to use. If I try to run any program at all, it doesn't know what to do. For example, it is totally lost trying to run the command line. If I bring up Windows Explorer and navigate to Windows\System32 and try to run the command line, or anything at all from there, it goes "Huh?" What in heck has happened?? Is it possible to fix this, and if so, how? As an aside, I can log into my account (my account on that machine is an administrator) and it works fine.

  Read the article

• Fixed ruby/mysql connection with new libmysql.dll, and broke Apache in the process

  - by jmtoporek

  Ok so bit of background - all my development has been on a local Windows 7 machine. I had Apache with PHP/MySQL running with no issues. Been using ruby (1.9.3 and latest rails release 3.2.9) with built in webrick server, but had a devil of a time connecting to mysql. Did some research, updated my libmysql.dll file in c:/ruby/bin and it worked! Very happy... except now Apache stopped working. In my attempt to resolve the issue I found an older copy of libmysql.dll, renamed the new file, copied the old file back to c:ruby/bin and apache works, ruby does not. So I can take this ass backwards approach but obviously this seems pretty stupid. I was surprised that Apache was using the dll file in ruby/bin folder. I presume this is related to path variables perhaps? I guess I was hoping someone could direct me as to how I can use one dll file for apache and another for ruby. Or if you have some other smarter approach - I've smart enough to follow directions to install apache from scratch and enable php on windows as well as ubuntu, but I'm not much of a sys admin, just a semi competent web developer.

  Read the article

• USB-to-Serial showing gibberish at 115200 Baud

  - by Mose

  I've got a serious problem which drives me crazy because I tried everything I could think of. First of all, I made a video: http://youtu.be/boghkuq7L_s but please read the following text for more information, not only view the video! When using a USB-to-Serial interface everything works as long as I don't go beyond 57600 Baud. At higher rates I only get giberish like this: év.­b0JNLYÆÿ¿iëd0U²(kßÞb! ú]/xscB!ï¯!BoXûÿ1ïâÖCÿ6ÌAnè*íÌC)º¿BíÞØ.C.@ÆÃwHJÂs "YE:ñ.èFðÌCÊ÷ÞÄ !x H w6@BtbHJ ̪ Ì6ì H¾a¿bH.">îvy®;f<ßBÌ p­L¨fæH­E ­þ¼MBÞI What makes the problem so strange is, I exchanged every component and the problem still presists. I tried differtent OSes (Ubuntu, WinXP, Win7, OSX 10.7) with 32 and 64 Bit. I tried USB-to-Serial interface from FTDI and Prolific. I tried reading the output from my Raspberry PI and from an Asterisk Appliance. I changed the cables and the wiring. Nothing helped. In the video I made a example with a old Notebook with native COM and put the USB-to-Serial to the same connection as "sniffer" (only Rx and GND connected) to make sure the output and everything is ok as one can see on the native port. The voltage is ok. Settings for both are 115200 Baud, 8 Bit with 1 Stop and no flow control. Native is ok. USB is messed up. I used the newest drivers and double checked all connections. I have no idea what is wrong here. As I couldn't find anyone describing problems like this I question my long experiance in computer science and think I'm doing some completly wrong... Please help :-/

  Read the article

< Previous Page | 486 487 488 489 490 491 492 493 494 495 496 497  | Next Page >