Search Results

Search found 12944 results on 518 pages for 'desktop publishing'.

Page 491/518 | < Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• Linux Mint 14 severe overheating

  - by agvares

  I've tried switching to Mint (it was Mint 12) about 6 months ago, but failed to do it due to enormous overheating which made it virtually impossible to run any applications more complex than Gedit. Time had passed, and now I'm back again with Mint 14, but feeling way more determined. What I face are the following issues: 1) Great overheating (and by great I mean that just by doing nothing my CPU temp is floating around 70-75 C, which I find a lot) 2) Running multiple applications (let's say Chrome, Skype and Pidgin) results in critical overheating and immediate shutdown of the system 3) Due to the stuff listed above, my battery drains in about 10-15 minutes, pretty much turning my laptop into a crippled desktop machine I've got a HP-dv6 laptop (i7, 6gb RAM, dual graphics) Here's the output of lspci: 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.2 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 3 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler XT [AMD Radeon HD 6700M Series] 07:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0d:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 13:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5209 PCI Express Card Reader (rev 01) 19:00.0 USB controller: NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04) what i've tried to do already: 1) I've edited my grub file to add some "splash" arguments there 2) Installed jupiter and powertop 3) Tried to upgrade to newer kernels (up to 3.8), btw running anything newer than 3.5 results in both resolution and wi-fi detection fail 4) Read lots of forum threads devoted to the topic So, my question is simple: What else might I do to become finally able to use Mint as my default OS without the risk of being burned alive by the CPU heat?

  Read the article

• Windows 8.1 IRQL_NOT_LESS_OR_EQUAL with Asus PCE-n53

  - by JArsenault89

  I saw the following question, and it is the exact same problem on my machine, I have tracked it to the ASUS PCE-n53 wireless card in my desktop. Does anyone know of a workaround? Windows 8.1 RTM installation crashes The adapter worked fine in windows 8... any ideas? EDIT: Crash Dump Analysis * Bugcheck Analysis * * IRQL_NOT_LESS_OR_EQUAL (a) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If a kernel debugger is available get the stack backtrace. Arguments: Arg1: 0000000000000000, memory referenced Arg2: 0000000000000002, IRQL Arg3: 0000000000000001, bitfield : bit 0 : value 0 = read operation, 1 = write operation bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status) Arg4: fffff801ef4f1316, address which referenced memory Debugging Details: WRITE_ADDRESS: 0000000000000000 CURRENT_IRQL: 2 FAULTING_IP: nt!KeReleaseSpinLock+16 fffff801`ef4f1316 f048832100 lock and qword ptr [rcx],0 DEFAULT_BUCKET_ID: WIN8_DRIVER_FAULT BUGCHECK_STR: AV PROCESS_NAME: System ANALYSIS_VERSION: 6.3.9600.16384 (debuggers(dbg).130821-1623) amd64fre TRAP_FRAME: ffffd00020d45550 -- (.trap 0xffffd00020d45550) NOTE: The trap frame does not contain all registers. Some register values may be zeroed or incorrect. rax=0000000000000001 rbx=0000000000000000 rcx=0000000000000000 rdx=0000000055920200 rsi=0000000000000000 rdi=0000000000000000 rip=fffff801ef4f1316 rsp=ffffd00020d456e0 rbp=ffffd00020d45768 r8=0000000055920222 r9=0000000035930000 r10=0000000055920222 r11=ffffd00020d456a8 r12=0000000000000000 r13=0000000000000000 r14=0000000000000000 r15=0000000000000000 iopl=0 nv up ei pl zr na po nc nt!KeReleaseSpinLock+0x16: fffff801ef4f1316 f048832100 lock and qword ptr [rcx],0 ds:0000000000000000=???????????????? Resetting default scope LOCK_ADDRESS: fffff801ef6da360 -- (!locks fffff801ef6da360) Resource @ nt!PiEngineLock (0xfffff801ef6da360) Exclusively owned Contention Count = 6 Threads: ffffe000010ff040-01<* 1 total locks, 1 locks currently held PNP_TRIAGE: Lock address : 0xfffff801ef6da360 Thread Count : 1 Thread address: 0xffffe000010ff040 Thread wait : 0x1fbe LAST_CONTROL_TRANSFER: from fffff801ef5647e9 to fffff801ef558ca0 STACK_TEXT: ffffd00020d45408 fffff801ef5647e9 : 000000000000000a 0000000000000000 0000000000000002 0000000000000001 : nt!KeBugCheckEx ffffd00020d45410 fffff801ef56303a : 0000000000000001 0000000000000000 ffff0c83e3e25300 ffffd00020d45550 : nt!KiBugCheckDispatch+0x69 ffffd00020d45550 fffff801ef4f1316 : 00000000000a5890 0000000000000001 0000000000000000 ffffe00004c00000 : nt!KiPageFault+0x23a ffffd00020d456e0 fffff80003b430ad : 00000000000afe80 ffffe00004c00000 00000000000a2f80 0000000035720000 : nt!KeReleaseSpinLock+0x16 ffffd00020d45710 fffff80003ac249f : ffffe00004c00000 00000000000000a8 ffffe00004c85050 0000000000000800 : netr28x+0x840ad ffffd00020d457b0 fffff80000b76475 : ffffd00020d459e8 ffffd00020d459f0 ffffe00004ac2006 ffffe00004ac21a0 : netr28x+0x349f ffffd00020d459a0 fffff80000baa248 : ffffe00004ac2eb8 0000000000000000 ffffe00000000000 ffffe00004ac21a0 : ndis!ndisMInvokeInitialize+0x39 ffffd00020d459e0 fffff80000b74784 : 0000000000000050 ffffe00004907ba0 0000000000000000 01cecbbc328e6cde : ndis!ndisMInitializeAdapter+0x4dc ffffd00020d46050 fffff80000b74d3d : 0000000000000050 ffffe0000443e770 ffffc00000951480 ffffe00004ac21a0 : ndis!ndisInitializeAdapter+0x60 ffffd00020d460a0 fffff80000b74c14 : ffffe00004ac21a0 ffffe00004ac2050 ffffe000047ec2a0 0000000000000000 : ndis!ndisPnPStartDevice+0x89 ffffd00020d460f0 fffff80000b87695 : ffffe00004ac21a0 ffffe00004ac21a0 ffffd00020d461b0 ffffe000047ec2a0 : ndis!ndisStartDeviceSynchronous+0x58 ffffd00020d46140 fffff80000b6a760 : ffffe000047ec2a0 ffffe00004ac21a0 0000000000000000 0000000000000000 : ndis!ndisPnPIrpStartDevice+0x13471 ffffd00020d46170 fffff8000032576c : ffffe00004b11501 ffffe00004b11570 0000000000000001 fffff80000325880 : ndis!ndisPnPDispatch+0x140 ffffd00020d461e0 fffff8000030b40a : ffffe000047ec2a0 0000000000000106 ffffd00020d462f0 ffffe00004b116c0 : Wdf01000!FxPkgFdo::PnpSendStartDeviceDownTheStackOverload+0xe8 ffffd00020d46250 fffff80000305942 : 0000000000000106 ffffd00020d462f0 0000000000000105 ffffd00020d464d0 : Wdf01000!FxPkgPnp::PnpEventInitStarting+0xa ffffd00020d46280 fffff80000305a5a : ffffe00004b116c8 0000000000000002 ffffe00004b11570 ffffe00004b11600 : Wdf01000!FxPkgPnp::PnpEnterNewState+0x102 ffffd00020d46310 fffff80000305bc4 : 0000000000000000 ffffd00020d46400 ffffe00004b116a0 0000000000000000 : Wdf01000!FxPkgPnp::PnpProcessEventInner+0xc2 ffffd00020d46390 fffff8000030c27a : 0000000000000000 ffffe00004b11570 0000000000000000 ffffe00004b11570 : Wdf01000!FxPkgPnp::PnpProcessEvent+0xe4 ffffd00020d46430 fffff80000300936 : ffffe00004b11570 ffffd00020d464c0 0000000000000000 ffffe00004a0e630 : Wdf01000!FxPkgPnp::_PnpStartDevice+0x1e ffffd00020d46460 fffff800002fba18 : ffffe000047ec2a0 ffffe000047ec2a0 0000000000000000 ffffe0000486f020 : Wdf01000!FxPkgPnp::Dispatch+0xd2 ffffd00020d464d0 fffff801ef838796 : 0000000000000000 fffff801ef6aa101 0000000000000000 ffffd000208aa180 : Wdf01000!FxDevice::DispatchWithLock+0x7d8 ffffd00020d465b0 fffff801ef4d5bad : ffffe000011dc3a0 ffffd00020d46659 0000000000000000 fffff801ef7f5ba4 : nt!PnpAsynchronousCall+0x102 ffffd00020d465f0 fffff801ef838e57 : ffffe000011db8d0 ffffe000011db8d0 ffffe00004a8d060 ffffc00002b11200 : nt!PnpStartDevice+0xc5 ffffd00020d466c0 fffff801ef838fe7 : ffffe000011db8d0 ffffe000011db8d0 0000000000000000 ffffe000011db8d0 : nt!PnpStartDeviceNode+0x147 ffffd00020d46790 fffff801ef7fd19e : ffffe000011db8d0 0000000000000001 0000000000000001 ffffe00000000001 : nt!PipProcessStartPhase1+0x53 ffffd00020d467d0 fffff801ef897b17 : ffffe000011db8d0 0000000000000001 0000000000000000 fffff801ef7ef7b2 : nt!PipProcessDevNodeTree+0x3ce ffffd00020d46a50 fffff801ef4f5033 : 0000000100000003 0000000000000000 0000000000000000 0000000000000000 : nt!PiRestartDevice+0xaf ffffd00020d46aa0 fffff801ef44565d : fffff801ef4f4c90 ffffd00020d46bd0 0000000000000000 ffffe00004a10170 : nt!PnpDeviceActionWorker+0x3a3 ffffd00020d46b50 fffff801ef4eec80 : 0000000000000000 ffffe000010ff040 ffffe000010ff040 ffffe0000035c900 : nt!ExpWorkerThread+0x2b5 ffffd00020d46c00 fffff801ef55f2c6 : ffffd00020472180 ffffe000010ff040 ffffe00000608040 ffffc00000002710 : nt!PspSystemThreadStartup+0x58 ffffd00020d46c60 0000000000000000 : ffffd00020d47000 ffffd00020d41000 0000000000000000 0000000000000000 : nt!KiStartSystemThread+0x16 STACK_COMMAND: kb FOLLOWUP_IP: netr28x+840ad fffff800`03b430ad 4533e4 xor r12d,r12d SYMBOL_STACK_INDEX: 4 SYMBOL_NAME: netr28x+840ad FOLLOWUP_NAME: MachineOwner MODULE_NAME: netr28x IMAGE_NAME: netr28x.sys DEBUG_FLR_IMAGE_TIMESTAMP: 51de7a8d FAILURE_BUCKET_ID: AV_netr28x+840ad BUCKET_ID: AV_netr28x+840ad ANALYSIS_SOURCE: KM FAILURE_ID_HASH_STRING: km:av_netr28x+840ad FAILURE_ID_HASH: {a1f86ced-f566-ac23-afeb-1aa88ea5ab8f} Followup: MachineOwner

  Read the article

• Stack-based keyboard delay using Logitech MX3100 keyboard

  - by Mark S. Rasmussen

  I've been using a Logitech Cordless Desktop MX3100 keyboard for quite a while. I've never really had any problems, except for the occasional typo. I noticed however that I tended make the typo "Laod" instead of "Load", quite a bit more often than any other typos. As it started to get on my nerves, I decided to do some testing. What I found out was than when I write lowercase "load", I'd never make the typo. All uppercase, or just uppercase L, I'd make the typo quite often. My actual (very scientific) testing is probably best described by showing the output: moatmoatmoat MoatMoatMoat loatloatloat LaotLaotLaot loafloafloaf LaofLaofLaof hoathoathoat HoatHoatHoat hoadhoadhoad HoadHoadHoad lortlortlort LrotLrotLrot What i found out was that whenever shift was depressed, typing an uppercase "L" would induce a significant lag if the next character was an "o", compared to the lag of the any other key: High "o" lag: LoLoLoLoLoLo No "a" lag: LaLaLaLaLaLa No lag for neither "o" nor "a": lolololololo lalalalalala By realizing this I regained a slight bit of sanity as I knew I wasn't coming down with a case of Parkinsons. I was actually typing correctly, the lag just interpreted it wrongly. Now, what really bugs me is that I can't fathom how this is occurring. What I'm actually typing, in physical order, is this: L - o - a - d, and yet, the "a" is output before the "o", even though "o" was pressed before "a". So while the keyboard is processing the "Lo" combo, the "a" gets prioritized and is inserted before the "o" is done processing, resulting in Laod instead of Load. And this only happens when typing "Lo", not when typing lowercase "lo". This problem could stem from the keyboard hardware, the receiver hardware or the keyboard software driver. No matter the fault location however, I can't imagine how this could be implemented as anything but a FIFO queue. A general delay, sure, I could live with that, albeit I'd be irritated. But a lag affecting different keys differently, and even resulting in unpredictable outcome - that just doesn't make any sense. I've solved the problem by just switching to a wired keyboard. I just can't shake it off me though; what kind of bug/error/scenario would result in a case like this? Edit: It's been suggested that I stop drinking Red Bull and stick to water instead. While that may actually help solve the issue, I'm really not looking for a solution as such. I'm more interested in an explanation of how this could happen, as I can't imagine any viable technical solution that could result in this behavior.

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• USB mouse disconnecting and reconnecting randomly and often

  - by Marc

  Specs: Q6600, evga 780I sli mobo, 4gig RAM, logitech MX518, windows 7 64bit, evga gtx 260, 650W power supply (single rail) The problem I am having is my mouse will reconnect/disconnect (will even hear the sounds from windows) and the light on the bottom of the mouse will turn off/turn on as it starts working again. It really sucks to be playing a game (and happens on desktop as well) for the mouse to just die out for a few seconds and come back. Sometimes it will not happen for days and other times it will do it 2 or more times within 15 seconds. I have tried two different wired mice, have tried multiple USB ports (on front of computer, back of computer, have also used a USB hub and have also plugged in a card that connects to the USB connectors on the motherboard and adds a few usb ports to the back of the computer, and I also bought a USB 2.0 PCI card and that did not help). Nothing else seems to reconnect like this, my usb keyboard has never once cut out like the mouse does and neither have any of the other devices I have connected (webcam, usb hub, various devices sometimes connected through usb cables, and IR reciever for windows media center remote). I have disconnected all usb devices except for my keyboard and mouse and the problem still occurs. I guess it could be something wrong with my motherboard but since no other devices behave similarly I'm just hoping that it is some kind of driver conflict. Installing logitech's drivers has had no effect. It seemed at first that if I go to device manager and uninstall HID-compliant mouse (that and logitech mx518 are listed) that would fix it but it doesn't seem to work anymore or at least not every time (it keeps reinstalling). I have googled "usb mouse disconnects and reconnects" and it seems to be fairly common but none of those were resolved. To stick some easy steps: It happens with or without the drivers installed It has happened with multiple mice on the same computer Bios is the latest version (P08) Motherboard drivers are the latest version Device manager is listing no problems on any USB devices Happens with every usb port, even addon usb cards Happens when all usb devices aside from mouse and keyboard are unplugged I read that maybe it is an IRQ conflict and I tried to look into that but did not really know what was going on, but didn't see anything obviously wrong. Thanks for any help guys, its driving me crazy!

  Read the article

• Unable to connect to SVN server on VPS : Subversion Configuration Problem

  - by Pritam Barhate

  Hello everybody, I purchased a VPS account (centos-5-x86_64) from Hostgator mainly for the purpose of setting up an online Subversion Server. This is the first time I am managing a VPS and my linux skills are not so great, but I have basic knowledge of the OS and have been using it on and off as desktop from last few years. So after foxing through a few tutorials online, as the first step I logged in using SSH root account provided by Hostgator and tried to run, yum install mod_dav_svn subversion As it turns out my account has Cpanel/WHM and since it some concept of easy apache straight forward procedure of yum install mod_dav_svn subversion won't work. After that I found out how it can be worked out by compiling the source and stuff. But the whole procedure looked long and scary. [I am just a linux nub]. so I decided I would just skip whole apache integration stuff and just access the server using svn:// protocol, anyways that's how I configure svn on our LAN. So I installed subversion using yum install subversion It installed fine. Then I created a folder /svn_repos/testproject and ran svnadmin create /svn_repos/testproject/ No Problems Using vi I changed svnserve.conf and passwd files for the repository and added a user with my name. Anonymous users don't have any access, authenticated users have write access. Then I started svnserve using svnserve -d then in same terminal window svn list svn://localhost/svn_repos/testproject Asks for authentication for realm, provided root password then for svn username and password. Provided both. The command returns nothing but exists properly. Returns nothing is understood I didn't import anything. But if try to access svn remotely using in another terminal: svn list svn://ip.add.of.server/svn_repos/testproject svn: Can't connect to host 'ip.add.of.server': Operation timed out Is what I get. Parallels Power Panel that I got from Hostgator reports that: The firewall is not active now. To activate the firewall, choose one of the firewall operation modes. So if firewall is not running and I can access svn using localhost, why the operation is timing out when I try to access svn from a remote machine? Experienced network admins please help. Thanks in advance. Also please suggest a good book which gives detailed information on configuring Dedicated servers + WHM and CPanel.

  Read the article

• HOSTS ignored when disconnected [closed]

  - by Synetech

  Problem I’m seeing a strange and extremely frustrating problem. Any system that is not connect to the Internet (Windows 7 shows the no Internet access icon because it cannot constantly ping Microsoft’s servers) cannot even access locally hosted servers. Hypothesis The problem appears to be that the HOSTS file is not being used to resolve DNS entries when there are no active NICs. Tests / Reproduction You can reproduce it as so: Disconnect a system from the Internet (make sure all wired and wireless connections are disconnected). If necessary, add an entry to the HOSTS file (e.g., 127.0.0.1 foobar or 127.0.0.1 foobar.com) Open a command-prompt Type ping foobar or ping foobar.com Observations The screenshots below show a clear and demonstrative example. In the first snap, a laptop is connected to a router wirelessly. The HOSTS file has only three entries and they resolve just fine. In the second snap, the wireless radio is turned off, so the entries in the HOSTS file are ignored. Moreover, notice that pinging localhost still works even without any active NICs (as does 127.0.0.1), but it is using the IPv6 address (must be hard-coded). You can see the same results in Windows XP with no IPv6 installed, so it has nothing to do with IPv6. I tried pining what should have resolved to 127.0.0.1 while the desktop system (with no wireless NICs) was connected via its Ethernet adapter, then again after pulling the cable from the router and waiting a couple of seconds, then again after plugging the cable back in. The same thing happens if instead of pulling out the cable, the NIC is disabled through software (the [Disable] button in the NIC’s Status dialog or via Device Manager). Conclusions It looks as though the HOSTS file is only being read and used if there is an active NIC, otherwise it is being ignored. This makes some sense in that if there are no active network adapters, then presumably there will not be any network activity, and thus no need to resolve host names via the HOSTS file. This assumption is specious however because it precludes locally hosted virtual servers. The HOSTS file should be used regardless of external DNS server connectivity, otherwise you cannot use simple/consistent/testing-production names for locally hosted servers when not connected to the Internet (for example web servers; help servers for Visual Studio, 3dsmax, etc.; and so on). Question Does anyone know how to force Windows to use the HOSTS file even if there are no active NICs? Appendix Figure 1: While the wireless NIC is connected to the router (the cable-modem is in standby, so no external Internet connectivity). Figure 2: With the wireless radio turned off (the Ethernet port is not unconnected in both cases). Figure 3: Same results in XP with no IPv6

  Read the article

• File/printer sharing issues on network with multiple OSes

  - by DanZ

  My workplace consists of computers running a variety of different operating systems, and I have been running into problems getting some of them to connect to a shared drive and printer over the network. Here is a brief description of the computers involved and the issues I have encountered: 1: Dell desktop, Windows Vista Business-- This is the computer I want the others to connect to. It has a USB printer and eSATA hard drive enclosure that I have set up for sharing, with different accounts for the various users. 2: Fujitsu laptop, Windows XP Tablet edition-- No problems. Can connect to both the shared printer and hard drive. 3: Lenovo laptop, Windows Vista Business 64 bit-- No problems. Can connect to both the shared printer and drive. 4: Apple MacBook, OS 10.4-- Can connect to the shared drive, but not to the shared printer. I am aware that the printer issue is due to a known incompatibility between Vista and OS 10.4 and earlier with regards to Samba. It is not a big problem, however, as this computer can access a network printer. 5: Sony laptop, Windows Vista Home Premium-- Can connect to the shared printer, but not the shared drive. It can see computer 1 and its shared drive on the network, and appears to successfully log in to user accounts. However, if you try to access the shared drive, it says you do not have permission. I have tried both standard and administrator accounts, and none can access the drive from this computer. 6: MacBook Pro, OS 10.5 (there are two of these)-- Can connect to the shared printer, but not the shared drive. They can't see computer 1 on the network. For that matter, they also can't see each other or the older Mac, but can see and access shared folders on the XP machine (computer 2) and can see other PCs in the building. I was able to add the shared printer manually by typing in its network location, but was unable to manually add the shared drive in the same way. So, what I am looking for is suggestions on how to get computers 5 and 6 to connect to the shared drive. Since they can already connect to the shared printer (which is on the same computer as the shared drive), it seems reasonable that they should be able to access the drive as well.

  Read the article

• Best Processor for MediaSmart Server?

  - by Kent Boogaart

  I'm trying to figure out what the best possible processor is that I can stick in my HP MediaSmart server. I'm clueless when it comes to correlating CPUs to motherboards. I suspect it's the socket type I care about, but I worry that there's more to it. CPU-Z gives me (excerpt): Processors Information ------------------------------------------------------------------------- Processor 1 ID = 0 Number of cores 1 (max 1) Number of threads 1 (max 1) Name AMD Sempron LE-1150 Codename Sparta Specification AMD Sempron(tm) Processor LE-1150 Package Socket AM2 (940) CPUID F.F.1 Extended CPUID F.7F Brand ID 1 Core Stepping DH-G1 Technology 65 nm Core Speed 1000.0 MHz Multiplier x FSB 5.0 x 200.0 MHz HT Link speed 800.0 MHz Stock frequency 2000 MHz Instructions sets MMX (+), 3DNow! (+), SSE, SSE2, SSE3, x86-64 L1 Data cache 64 KBytes, 2-way set associative, 64-byte line size L1 Instruction cache 64 KBytes, 2-way set associative, 64-byte line size L2 cache 256 KBytes, 16-way set associative, 64-byte line size FID/VID Control yes Max FID 10.0x Max VID 1.350 V P-State FID 0x2 - VID 0x12 (5.0x - 1.100 V) P-State FID 0xA - VID 0x0C (9.0x - 1.250 V) P-State FID 0xC - VID 0x0A (10.0x - 1.300 V) K8 Thermal sensor yes K8 Revision ID 6.0 Attached device PCI device at bus 0, device 24, function 0 Attached device PCI device at bus 0, device 24, function 1 Attached device PCI device at bus 0, device 24, function 2 Attached device PCI device at bus 0, device 24, function 3 Chipset ------------------------------------------------------------------------- Northbridge SiS 761GX rev. 02 Southbridge SiS 966 rev. 59 Graphic Interface AGP AGP Revision 3.0 AGP Transfer Rate 8x AGP SBA supported, enabled Memory Type DDR2 Memory Size 2048 MBytes Channels Single Memory Frequency 200.0 MHz (CPU/5) CAS# latency (CL) 5.0 RAS# to CAS# delay (tRCD) 5 RAS# Precharge (tRP) 5 Cycle Time (tRAS) 15 Bank Cycle Time (tRC) 21 Command Rate (CR) 1T DMI ------------------------------------------------------------------------- DMI BIOS vendor Phoenix Technologies, LTD version R03 date 05/08/2008 DMI System Information manufacturer HP product MediaSmart Server version unknown serial CN68330DGH UUID A482007B-B0CC7593-DD11736A-407B7067 DMI Baseboard vendor Wistron model SJD4 revision A.0 serial unknown DMI System Enclosure manufacturer HP chassis type Desktop chassis serial unknown DMI Processor manufacturer AMD model AMD Sempron(tm) Processor LE-1150 clock speed 2000.0 MHz FSB speed 200.0 MHz multiplier 10.0x DMI Memory Controller correction 64-bit ECC Max module size 4096 MBytes DMI Memory Module designation A0 size 2048 MBytes (double bank) DMI Memory Module designation A1 DMI Memory Module designation A2 DMI Memory Module designation A3 DMI Port Connector designation PS/2 Mouse (internal) port type Mouse Port connector PS/2 connector PS/2 DMI Port Connector designation USB0 (external) port type USB DMI Physical Memory Array location Motherboard usage System Memory correction None max capacity 16384 MBytes max# of devices 4 DMI Memory Device designation A0 format DIMM type unknown total width 64 bits data width 64 bits size 2048 MBytes DMI Memory Device designation A1 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A2 format DIMM type unknown total width 64 bits data width 64 bits DMI Memory Device designation A3 format DIMM type unknown total width 64 bits data width 64 bits How do I figure out what options I have for an upgrade?

  Read the article

• Nginx + PHP - No input file specified

  - by F21

  I am running Ubuntu Desktop 12.04 with nginx 1.2.6. PHP is PHP-FPM 5.4.9. This is the relevant part of my nginx.conf: http { include mime.types; default_type application/octet-stream; sendfile on; root /www keepalive_timeout 65; server { server_name testapp.com; root /www/app/www/; index index.php index.html index.htm; location ~ \.php$ { fastcgi_intercept_errors on; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } server { listen 80 default_server; index index.html index.php; location ~ \.php$ { fastcgi_intercept_errors on; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; include fastcgi_params; } } } In my hosts file, I redirect 2 domains: testapp.com and test.com to 127.0.0.1. My web files are all stored in /www. From the above settings, if I visit test.com/phpinfo.php and test.com/app/www, everything works as expected and I get output from PHP. However, if I visit testapp.com, I get the dreaded No input file specified. error. So, at this point, I pull out the log files and have a look: 2012/12/19 16:00:53 [error] 12183#0: *17 FastCGI sent in stderr: "Unable to open primary script: /www/app/www/index.php (No such file or directory)" while reading response header from upstream, client: 127.0.0.1, server: testapp.com, request: "GET / HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "testapp.com" This baffles me because I have checked again and again and /www/app/www/index.php definitely exists! This is also validated by the fact that test.com/app/www/index.php works which means the file exists and the permissions are correct. Why is this happening and what are the root causes of things breaking for just the testapp.com v-host?

  Read the article

• installing windows XP in Samsung SENS 145 plus notebook (no CD drive)

  - by user13267

  Hi I was trying to install Windows XP in a Samsung SENS 145 plus Notebook. It does not have a cd drive and I already managed to format it and semi install Windows XP, so now it does not even boot up either. This is what I did: Since it supports USB booting, I first made a bootable USB of Windows XP (Korean version; SP2 I think, may be SP 3) using Novicorp WinToFlash enter link description here. It managed to boot up at first and I was able to format the C driveand get Windows install to start up. It took forever to copy all the files from the USB and after the first reboot, before installation started, I cancelled the reboot from windows install, went to BIOS and changed the boot device priority from USB to internal hard drive. But now on bootup it showed me a list with two options for booting windows XP (much like in the case of a multi OS system) so I assumed that I had formatted drive D by mistake and installed XP there, instead of on C drive. Anyway, I chose one of them and it continued my Windows installation. I got the blue installation screen that shows ads about Windows XP on the right frame and estimated remaining time on the left. However, after completing the process, after the first reboot, instead of showing the Windows XP logo, it says \system32\hall.dll is missing (or corrupted I'm not sure, I needed to install the Korean version of windows and I could not exactly read the error message, however it was one that I have already seen in an English version installation, and I am sure it says either missing or corrupted). The problem is, now it shows the same error again when I try to reboot it from the USB drive as well. I tried to boot a portable version of Linux I made in another USB, but the computer does not boot up from that USB, and it shows hal.dll error when I try to boot it using the WIN XP installation USB I made, as well as when I try to boot it from the hard drive, where I suppose Win XP is now semiinstalled. So now I can't get the computer to start up at all, except going to the BIOS. What else can I try to solve this? Also, would it be possible to install XP on this computer by connecting it to another one running Windows 7 ultimate, through the ethernet card? That is, network just the two computers together, then install windows XP on the notebook from the desktop running windows 7? Please help, I'm running out of ideas on this one. If Korean version of windows XP is the problem then I am willing to install English version as well. (but I need to make sure if that is the real cause of the problem)

  Read the article

• Disable Acer eRecovery system

  - by Joel Coehoorn

  The meat of this question is that I'm looking for a way to either require a password before using a recovery partition or "break" the recovery partition (specifically, Acer eRecovery) in a way that I can later "unbreak" only by booting normally into windows first. Here's the full details: I have a set of new Acer Veriton n260g machines in a computer lab. A lot work went into setting up this lab to work well - for example, Office 2007 and other programs needed by the students were installed, all windows updates are applied, and a default desktop is setup. All in all it's several hours work to fully set up one machine. Unfortunately, I don't currently have the ability to easily image these machines, and even if I did I would want to avoid downtime even while an image is restored. Therefore, I've taken steps to lock them down — namely DeepFreeze and a bios password to prevent booting from anywhere but the frozen hard drive. DeepFreeze is an amazing product — as long as you boot from the frozen hard drive, there is no way to actually make permanent changes to that hard drive. Anything you do is wiped after the machine restarts. It lets me give students the leeway to do what they want on lab computers without worrying about them breaking something. The problem is that even with the bios locked and set to only boot from the hard drive, these Acers still have a simple way to choose a different boot source: shut them down and put a paper click in a little hole at the top while you turn it on again. This puts them into the "Acer eRecovery" mode. This by itself is no big deal — you can still power cycle with no impact. But if you then click through the menu to reset the machine (we're now past the point of curiosity and on to intent) it will wipe the hard drive and restore it to the original state. Of course, a few students have already figured this out and reset a couple machines. That's unfortunate, but inevitable. I don't want to destroy the ability to do this entirely (which I could by repartitioning the drives to remove the recovery partition) but I would like a way to require a password first, or "break" the recovery system in a way that I can "unbreak" only if I first un-freeze the hard drive in DeepFreeze. Any ideas?

  Read the article

• Complete Active Directory redesign and GPO application

  - by Wolfgang Kuehne

  after much testing and hundreds of tries and hours invested I decided to consult you experts here. Overview: I want to apply some GPO to our users which will add some specific site to the Trusted Sites in Internet Explorer settings for all users. However, the more I try the more confusing the results become. The GPO is either applied to one group of users, or to another one. Finally, I came to the conclusion that this weird behavior is cause rather by the poor organization in Users and Groups in Active Directory. As such I want to kick the problem from the root: Redesign the Active Directory Users and Groups. Scenario: There is one Domain Controller, and we use Terminal Services (so there is a Terminal Server as well). Users usually log on to the Terminal Server using Remote Desktop to perform their daily tasks. I would classify the users in the following way: IT: Admins, Software Development Business: Administration, Management The current structure of the Active Directory Users and Groups is a result of the previous IT management. The company has used Small Business Server which has created multiple default user groups and containers. Unfortunately, the guys working before me have do no documentation at all. Now, as I inherit this structure I am in the no mans land. No idea which direction to head first. As you can see, the Active Directory User and Groups have become a bit confusing. There is no SBS anymore, but when migrating from SBS to the current Windows Server 2008 R2 environment the guys before me have simply copied the same structure. The real question: Where should I start cleaning from, ensuring that I won't break totally the current infrastructure? What is a nice organization for the scenario that I have explained above? Possible useful info for the current structure: Computers folder contains Terminal Services Computers user group Members: TerminalServer computer located at Server -> Terminalserver OU Member of: NONE Foreign Security Principals : EMPTY Managed Service Accounts : EMPTY Microsoft Exchange Security Groups : not sure if needed, our emails are administered by external service provider Distribution Groups : not sure if needed Security Groups : there are couple of groups which are needed SBS users : contains all the users Terminalserver : contains only the TerminalServer machine

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubu

  - by user37968

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Web Service gets unavailable after several concurrent calls

  - by Roman

  We are testing GoDaddy Virtual Data Center and came to a very strange issue when our web site gets unavailable. GoDaddy Support keeps saying the issue is in our web server settings, but looking at the result of our tests I doubt it. TEST ENVIRONMENT Virtual DataCenter with Windows hosted at GoDaddy.com. All servers have Windows Server 2008 R2 Datacenter, IIS 7. Server One with IP address 10.1.0.4 Server Two with IP address 10.1.0.3 Both servers are in private network not visible from outside. Port Forward with IP address 50.62.13.174. Port Forward is assigned to Server One TEST DESCRIPTION JMeter is used as a Client App to simulate 30 concurrent users sending 100 SOAP requests each. Interval between requests is 1 second. Http link used for testing: http://50.62.13.174/v2/webservices.asmx TEST ONE Test is run from a computer in our office. After JMeter starts running test, almost immediately, the link above becomes unavailable in a browser. After test completion, the link is not available in a browser for about 5 more minutes. Remote Desktop is working well, so we can connect to Server One remotely. After about 5 minutes since test completion, the link becomes available in a browser again. TEST TWO Test is run from Server Two (that is part of our virtual data center). Test works very well, no visible delays in processing. The link is available in a browser all the time. TEST THREE Test is run from Server One using localhost. The result is the same as in TEST TWO - no issues. TEST FOUR We repeated TEST ONE from other computers that we have located in different countries, all with the same result as TEST ONE. CONCLUSION As the test works well from Server Two, but does not work from outside our virtual data center, we feel there are issues with the network or its capacity. The whole behaviour looks like out requests from outside get stuck somewhere before reaching our virtual data center. Has anybody had similar issues in the past? Are there chances that something is wrong with our server settings?

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter EDIT: I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• Is Gmail Being Blocked by my ISP?

  - by james

  EDIT: I thought I pinpointed the problem. Just now I tried to go to the firefox addons page which uses https and gmail also uses https. So I thought I am unable to load https pages on this computer. So I went to a bank site which uses https but that loads just fine. Sigh.... I asked this over at superuser but they weren't able to help, so I was hoping the sysadmins here will be able to advise as to what's wrong. Although the issue here is with a PC and not a server it still deals with networking so I hope it's not too irrelevant. The Issue: I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail log in page starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping that a complete reinstall would solve the issue, but no luck. And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cable from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before that gmail was perfectly accessible in this computer. I can't remember anything special happening on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter I should mention I can access gmail and youtube just fine through a IP proxy service.

  Read the article

• ffmpeg video4linux2 at specified resolution

  - by wim

  When I'm trying to record a clip from my webcam, using: ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi I get annoying problem with very low resolution video, and there is a message from ffmpeg saying: [video4linux2,v4l2 @ 0x2bff3e0] The V4L2 driver changed the video from 800x600 to 176x144 I have tried not specifying -s, or trying other sizes like 800x600, and always it forces me back to 176x144. Why is this and how can I prevent it? My webcam is one of those Logitech 9000 Pro, I know it supports better resolutions than this and I can see with v4l2-ctl --list-formats-ext that it goes up to at least 800x600. edit: complete console output follows wim@wim-desktop:~$ ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi ffmpeg version git-2012-11-20-70c0f13 Copyright (c) 2000-2012 the FFmpeg developers built on Nov 21 2012 00:09:36 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 8.100 / 52. 8.100 libavcodec 54. 73.100 / 54. 73.100 libavformat 54. 37.100 / 54. 37.100 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 23.101 / 3. 23.101 libswscale 2. 1.102 / 2. 1.102 libswresample 0. 17.100 / 0. 17.100 libpostproc 52. 2.100 / 52. 2.100 [video4linux2,v4l2 @ 0x37a33e0] The V4L2 driver changed the video from 640x480 to 176x144 [video4linux2,v4l2 @ 0x37a33e0] Estimating duration from bitrate, this may be inaccurate Input #0, video4linux2,v4l2, from '/dev/video0': Duration: N/A, start: 37066.740548, bitrate: 6082 kb/s Stream #0:0: Video: rawvideo (YUY2 / 0x32595559), yuyv422, 176x144, 6082 kb/s, 15 tbr, 1000k tbn, 15 tbc File '/tmp/spam.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to '/tmp/spam.avi': Metadata: ISFT : Lavf54.37.100 Stream #0:0: Video: mpeg4 (FMP4 / 0x34504D46), yuv420p, 176x144, q=2-31, 200 kb/s, 15 tbn, 15 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> mpeg4) Press [q] to stop, [?] for help frame= 95 fps= 22 q=2.0 Lsize= 88kB time=00:00:13.86 bitrate= 51.8kbits/s video:77kB audio:0kB subtitle:0 global headers:0kB muxing overhead 13.553706%

  Read the article

• New monitor connected to HDMI adaptor doesn't show output after booting

  - by Paul

  Hello out there in the multiple monitors’ world. I am a very old newbie in your world and need help. I just purchased a new Asus VH236H monitor and hooked it up the HDMI port of an ATI Radeon HD4300 / 4500 Series display adaptor. I left the old Princeton LCD19 (TMDS) hooked up to the DVI port of the same display adaptor. Both monitors displayed the boot sequence, after I fired good old Sarastro2 (Asus P5Q Pro Turbo – Dual Core E5300 – 2.60 GHz) up. The Asus lacked one half of a second behind the Princeton until the Windows 7 Ultimate SP 1 boot up was complete. Then the Asus displayed “HDMI NO SIGNAL” and went into hibernation. The Princeton stayed lit up as before. Both monitors are displayed on the “Screen Resolution Setup Display” and I plaid around with them for a while. The only thing I accomplished was to shove the desktop icons from the Princeton to the still hibernating Asus. The “Multiple displays:” is set to “Extend these displays”, the Orientation is “Landscape” and the Resolutions are set on both to the “recommended” one. Both monitors show that they work properly in the advanced Properties display. What am I doing wrong, what am I missing? Never mind the opinions about the different resolutions of the two monitors. I always can unhook the Princeton and give it to a Goodwill Store if I do not like the setup. I just would like to make it work. Any constructive help is very much appreciated, Thank you. Thank you Anees Bakrain Only the ATI Radeon HD 4300/4500 Series adapter is displayed in the Device Manager, for that reason I have to assume that the onboard display adaptor is not active. All 40 drivers of Sarastro2 are up to date and the HDMI cable can not be the problem because both monitors displayed the boot sequence up to the moment when Windows 7 was loaded completely. This was the moment, when the Asus monitor lost its signal. Both connectors, HDMI and DVI are connected and removing the DVI connector would not solve my problem of running both monitors simultaneously. However, your suggestions shifted my seventy one year old brain into the next gear. The only question remaining is; “Why the signals to the Asus monitor stop after the sequence is complete”. The ATI Radeon HD 4300/4500 Series adapter seems to be capable of sending simultaneous HDMI and DVI signals, what is done during the boot sequence. Why do the signals change after the boot sequence is complete is the key question or der springende Punkt? Is this a correct assumption slhck?

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• Permissions denied on apache rewrite module virtual host configuration

  - by sina

  All of a sudden I keep getting "Permissions denied" on apache 2 virtualhost once we moved it to its own conf file. I have tried all the suggestions I have found here but none work. Please can someone tell me what I am doing wrong? Thanks! <VirtualHost *:80> DocumentRoot "/var/www/mm" <Directory "/var/www/mm"> Options +Indexes +MultiViews +FollowSymLinks AllowOverride all Order deny,allow Allow from all AddType text/vnd.sun.j2me.app-descriptor .jad AddType application/vnd.rim.cod .cod </Directory> Alias /holdspace "/var/www/mm/holdspace" RewriteLogLevel 9 RewriteLog "/var/log/httpd/rewrite.log" RewriteEngine on # 91xx RewriteCond %{HTTP_USER_AGENT} BlackBerry.9105 RewriteRule ^/download/(.*) /holdspace/bb6-360x480/$1 [L] # 92xx RewriteCond %{HTTP_USER_AGENT} BlackBerry.9220 RewriteRule ^/download/(.*) /holdspace/bb5-320x240/$1 [L] Errors in error.log: [Wed May 28 12:44:58 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /download/eazymoney.jad denied [Wed May 28 12:44:58 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /favicon.ico denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /favicon.ico denied [Wed May 28 12:44:59 2014] [error] [client 197.255.173.95] (13)Permission denied: access to /error/HTTP_FORBIDDEN.html.var denied Errors in rewrite.log: 197.255.173.95 - - [28/May/2014:12:46:01 +0100] [41.203.113.103/sid#7fe41704ca28][rid#7fe417123378/initial/redir#1] (3) applying pattern '^/download/(.*)' to uri '/error/HTTP_FORBIDDEN.html.var' 197.255.173.95 - - [28/May/2014:12:46:01 +0100] [41.203.113.103/sid#7fe41704ca28][rid#7fe417123378/initial/redir#1] (3) applying pattern '^/download/(.*)' to uri '/error/HTTP_FORBIDDEN.html.var' Apache Configuration file: ServerTokens Prod ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 60 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 4 MaxClients 300 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> Listen 80 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule include_module modules/mod_include.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule status_module modules/mod_status.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule info_module modules/mod_info.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule userdir_module modules/mod_userdir.so LoadModule alias_module modules/mod_alias.so LoadModule substitute_module modules/mod_substitute.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_ajp_module modules/mod_proxy_ajp.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost ServerName sv001zma002.africa.int.myorg.com UseCanonicalName Off DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_userdir.c> UserDir disabled </IfModule> DirectoryIndex index.html index.html.var AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy All </Files> TypesConfig /etc/mime.types DefaultType text/plain <IfModule mod_mime_magic.c> MIMEMagicFile conf/magic </IfModule> HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature Off TraceEnable Off Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options MultiViews FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_dav_fs.c> DAVLockDB /var/lib/dav/lockdb </IfModule> ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable Charset=UTF-8 AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv zh-CN zh-TW ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddType application/x-x509-ca-cert .crt AddType application/x-pkcs7-crl .crl AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml ProxyErrorOverride On Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> ErrorDocument 400 /error/HTTP_BAD_REQUEST.html.var ErrorDocument 401 /error/HTTP_UNAUTHORIZED.html.var ErrorDocument 403 /error/HTTP_FORBIDDEN.html.var ErrorDocument 404 /error/HTTP_NOT_FOUND.html.var </IfModule> </IfModule> BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully ErrorDocument 400 "Bad Request"

  Read the article

• AWS EC2 - How to specify an IAM role for an instance being launched via awscli

  - by Skaperen

  I am using the "aws ec2 run-instances" command (from the awscli package) to launch an instance in AWS EC2. I want to set an IAM role on the instance I am launching. The IAM role is configured and I can use it successfully when launching an instance from the AWS web UI. But when I try to do this using that command, and the "--iam-instance-profile" option, it failed. Doing "aws ec2 run-instances help" shows Arn= and Name= subfields for the value. When I try to look up the Arn using "aws iam list-instance-profiles" it gives this error message: A client error (AccessDenied) occurred: User: arn:aws:sts::xxxxxxxxxxxx:assumed-role/shell/i-15c2766d is not authorized to perform: iam:ListInstanceProfiles on resource: arn:aws:iam::xxxxxxxxxxxx:instance-profile/ (where xxxxxxxxxxxx is my AWS 12-digit account number) I looked up the Arn string via the web UI and used that via "--iam-instance-profile Arn=arn:aws:iam::xxxxxxxxxxxx:instance-profile/shell" on the run-instances command, and that failed with: A client error (UnauthorizedOperation) occurred: You are not authorized to perform this operation. If I leave off the "--iam-instance-profile" option entirely, the instance will launch but it will not have the IAM role setting I need. So the permission seems to have something to do with using "--iam-instance-profile" or accessing IAM data. I repeated several times in case of AWS glitches (they happen sometimes) and no success. I suspected that perhaps there is a restriction that an instance with an IAM role is not allowed to launch an instance with a more powerful IAM role. But in this case, the instance I am doing the command in has the same IAM role that I am trying to use. named "shell" (though I also tried using another one, no luck). Is setting an IAM role not even permitted from an instance (via its IAM role credentials)? Is there some higher IAM role permission needed to use IAM roles, than is needed for just launching a plain instance? Is "--iam-instance-profile" the appropriate way to specify an IAM role? Do I need to use a subset of the Arn string, or format it in some other way? Is it possible to set up an IAM role that can do any IAM role accesses (maybe a "Super Root IAM" ... making up this name)? FYI, everything involves Linux running on the instances. Also, I am running all this from an instance because I could not get these tools installed on my desktop. That and I do not want to put my IAM user credentials on any AWS storage as advised by AWS here. after answered: I did not mention the launching instance permission of "PowerUserAccess" (vs. "AdministratorAccess") because I did not realize additional access was needed at the time the question was asked. I assumed that the IAM role was "information" attached to the launch. But it really is more than that. It is a granting of permission.

  Read the article

• Hell: NTFS "Restore previous versions"...

  - by ttsiodras

  The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

  Read the article

< Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >