Search Results

Search found 13404 results on 537 pages for 'george host'.

Page 491/537 | < Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >

• Why does Ubuntu only detect one USB LAN adapters at a time?

  - by EGO

  I try to connect real switch with my computer for an exam preparation, for this purpose I need more than one LAN cards, and there is only one built in LAN card in my computer. So, to get more LAN cards, I bought 4 USB Ethernet adapters (as I have 4 usb ports in may laptop 2 usb 2.0 ports, 2 usb 3.0 ports). When I plug these adapters in my computer Ubuntu only detects one LAN card from 2.0 usb ports, and one LAN card from 3.0 ports. And sometimes detects only one USB LAN from all the usb ports. Actually the real problem is Ubuntu shows these USB LAN adapters in the "lsusb", but does not list them in "ifconfig". Kontron (Industrial Computer Source / ICS Advent) is my LAN USB ethernet. abc@ubuntu:~$ lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hu Bus 002 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 001 Device 003: ID 138a:0018 Validity Sensors, Inc. Bus 001 Device 004: ID 064e:e258 Suyin Corp. Bus 003 Device 011: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 013: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 003 Device 012: ID 0fe6:9700 Kontron (Industrial Computer Source / ICS Advent) Bus 002 Device 005: ID 0a5c:21b4 Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR -- etho is my built in LAN card, while eth1 is the only USB LAN card that ubuntu has detected. abc@ubuntu:~$ ifconfig eth0 Link encap:Ethernet HWaddr 2c:27:d7:a5:d2:39 inet6 addr: fe80::2e27:d7ff:fea5:d239/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:21056 errors:0 dropped:1 overruns:0 frame:0 TX packets:5669 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1407289 (1.4 MB) TX bytes:372566 (372.5 KB) Interrupt:49 Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:e0:4c:53:44:58 inet6 addr: fe80::2e0:4cff:fe53:4458/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9230 errors:0 dropped:0 overruns:0 frame:0 TX packets:9230 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:557648 (557.6 KB) TX bytes:557648 (557.6 KB) wlan0 Link encap:Ethernet HWaddr cc:52:af:5e:78:05 inet addr:192.168.1.65 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::ce52:afff:fe5e:7805/64 Scope:LinkU UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:17389 errors:0 dropped:0 overruns:0 frame:0 TX packets:12231 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22452248 (22.4 MB) TX bytes:1502750 (1.5 MB) If I unplug the USB LAN card which Ubuntu has detected, then Ubuntu will detect a USB LAN card from the remaining plugged adapters, and process go on untill I plug all the USB LAN adapters. Looking for some urgent help. Thanks

  Read the article

• ArchBeat Link-o-Rama Top 10 for September 9-15, 2012

  - by Bob Rhubart

  The Top 10 most-viewed items shared on the OTN ArchBeat Facebook page for the week of September 9-15, 2017. 15 Lessons from 15 Years as a Software Architect | Ingo Rammer In this presentation from the GOTO Conference in Copenhagen, Ingo Rammer shares 15 tips regarding people, complexity and technology that he learned doing software architecture for 15 years. Attend OTN Architect Day – by Architects, for Architects – October 25 You won't need 3D glasses to take in these live presentations (8 sessions, two tracks) on Cloud computing, SOA, and engineered systems. And the ticket price is: Zero. Nothing. Absolutely free. Register now for Oracle Technology Network Architect Day in Los Angeles. Thursday October 25, 2012, 8:00 a.m. – 5:00 p.m. Sofitel Los Angeles , 8555 Beverly Boulevard , Los Angeles, CA 90048. Cloud API and service designers, stop thinking small | Cloud Computing - InfoWorld "The focus must shift away from fine-grained APIs that provide some type of primitive service, such as pushing data to a block of storage or perhaps making a request to a cloud-rooted database," says InfoWorld's David Linthicum. "To go beyond primitives, you must understand how these services should be used in a much larger architectural context. In other words, you need to understand how businesses will employ these services to form real workplace solutions—inside and outside the enterprise." Adding a runtime picker to a taskflow parameter in WebCenter | Yannick Ongena Oracle ACE Yannick Ongena shows how to create an Oracle WebCenter popup to allow users to "select items or do more complex things." Oracle IAM 11g R2 docs are now available "One of the great things about the new doc set is the inclusion of ePub files," says Fusion Middleware A-Team blogger Chris Johnson. "This means that if you have an iPad you can load up the doc library onto that and read the docs on the couch." Setting up a local Yum Server using the Exalogic ZFS Storage Appliance | Donald A concise technical post from the man named Donald. What's New in Oracle VM VirtualBox 4.2? | The Fat Bloke Sings "One of the trends we've seen is that as the average host platform becomes more powerful, our users are consistently running more and more vm's," says The Fat Bloke. "Some of our users have large libraries of vm's of various vintages, whilst others have groups of vm's that are run together as an assembly of the various tiers in a multi-tiered software solution, for example, a database tier, middleware tier, and front-ends." The new VirtualBox release, a year in the making, addresses the needs of these users, he explains. Configuring Oracle Business Intelligence 11g MDS XML Source Control Management with Git Version Control | Christian Screen Oracle ACE Christian Screen developed this tutorial for those interested in learning how to configure the Oracle Business Intelligence 11g (11.1.1.6) metadata repository for development using the new MDS XML source control management functionality. Identity and Access Management at Oracle Open World 2012 | Brian Eidelman Fusion Middleware A-Team blogger Brian Eideleman highlights three Oracle Openworld sessions that will put Identity and Access Management in the spotlight, and shares a link to the "Focus On: Identity Management" document, a comprehensive listing of Openworld activities also dealing with IM. Starting and stopping WebLogic automatically using Upstart | Chris Johnson "In Ubuntu, RedHat and Oracle Linux there's a new flavor of init called Upstart that all the kids are using," says Oracle Fusion Middleware A-Team member Chris Johnson. "It's the new hotness when it comes to making programs into daemons and wiring them to start and stop at appropriate times." Thought for the Day "The purpose of software engineering is to control complexity, not to create it." — Pamela Zave Source: SoftwareQuotes.com

  Read the article

• RPi and Java Embedded GPIO: Sensor Reading using Java Code

  - by hinkmond

  And, now to program the Java code for reading the fancy-schmancy static electricity sensor connected to your Raspberry Pi, here is the source code we'll use: First, we need to initialize ourselves... /* * Java Embedded Raspberry Pi GPIO Input app */ package jerpigpioinput; import java.io.FileWriter; import java.io.RandomAccessFile; import java.text.DateFormat; import java.text.SimpleDateFormat; import java.util.Calendar; /** * * @author hinkmond */ public class JerpiGPIOInput { static final String GPIO_IN = "in"; // Add which GPIO ports to read here static String[] GpioChannels = { "7" }; /** * @param args the command line arguments */ public static void main(String[] args) { try { /*** Init GPIO port(s) for input ***/ // Open file handles to GPIO port unexport and export controls FileWriter unexportFile = new FileWriter("/sys/class/gpio/unexport"); FileWriter exportFile = new FileWriter("/sys/class/gpio/export"); for (String gpioChannel : GpioChannels) { System.out.println(gpioChannel); // Reset the port unexportFile.write(gpioChannel); unexportFile.flush(); // Set the port for use exportFile.write(gpioChannel); exportFile.flush(); // Open file handle to input/output direction control of port FileWriter directionFile = new FileWriter("/sys/class/gpio/gpio" + gpioChannel + "/direction"); // Set port for input directionFile.write(GPIO_IN); directionFile.flush(); } And, next we will open up a RandomAccessFile pointer to the GPIO port. /*** Read data from each GPIO port ***/ RandomAccessFile[] raf = new RandomAccessFile[GpioChannels.length]; int sleepPeriod = 10; final int MAXBUF = 256; byte[] inBytes = new byte[MAXBUF]; String inLine; int zeroCounter = 0; // Get current timestamp with Calendar() Calendar cal; DateFormat dateFormat = new SimpleDateFormat("yyyy/MM/dd HH:mm:ss.SSS"); String dateStr; // Open RandomAccessFile handle to each GPIO port for (int channum=0; channum Then, loop forever to read in the values to the console. // Loop forever while (true) { // Get current timestamp for latest event cal = Calendar.getInstance(); dateStr = dateFormat.format(cal.getTime()); // Use RandomAccessFile handle to read in GPIO port value for (int channum=0; channum Rinse, lather, and repeat... Compile this Java code on your host PC or Mac with javac from the JDK. Copy over the JAR or class file to your Raspberry Pi, "sudo -i" to become root, then start up this Java app in a shell on your RPi. That's it! You should see a "1" value get logged each time you bring a statically charged item (like a balloon you rub on the cat) near the antenna of the sensor. There you go. You've just seen how Java Embedded technology on the Raspberry Pi is an easy way to access sensors. Hinkmond

  Read the article

• Tyrus 1.8

  - by Pavel Bucek

  Another version of Tyrus, the reference implementation of JSR 356 – Java API for WebSocket is out! Complete list of fixes and features is below, but let me describe some of the new features in more detail. All information presented here is also available in Tyrusdocumentation. What’s new? First to mention is that JSR 356 Maintenance review Ballot is over and the change proposed for 1.1 release was accepted. More details about changes in the API can be found in this article. Important part is that Tyrus 1.8 implements this API, meaning you can use Lambda expressions and some features of Nashorn without the need for any workarounds. Almost all other features are related to client side support, which was significantly improved in this release. Firstly – I have to admit, that Tyrus client contained security issue – SSL Hostname verification was not performed when connecting to “wss” endpoints. This was fixed as part of TYRUS-339 and resulted in some changes in the client configuration API. Now you can control whether HostnameVerification should be performed (SslEngineConfigurator#setHostnameVerificationEnabled(boolean)) or even set your own HostnameVerifier (please use carefully): #setHostnameVerifier(…). Detailed description can be found in Host verification chapter. Another related enhancement is support for Http Basic and Digest authentication schemes. Tyrus client now enables users to provide credentials and underlying implementation will take care of everything else. Our implementation is strictly non pre-emptive, so the login information is sent always as a response to 401 Http Status Code. If the Basic and Digest are not good enough and there is a need to use some custom scheme or something which is not yet supported in Tyrus, custom Authenticator can be registered and the authentication part of the handshake process will be handled by it. Please seeClient HTTP Authentication chapter in the user guide for more details. There are other features, like fine-grain threadpool configuration for JDK client container, build-in Http redirect support and some reshuffling related to unifying the location of client configuration classes and properties definition – every property should be now part of ClientProperties class. All new features are described in the user guide – in chapterTyrus proprietary configuration. Update – Tyrus 1.8.1 There was another slightly late reported issue related to running in environments with SecurityManager enabled, so this version fixes that. Another noteworthy fixes are TYRUS-355 and TYRUS-361; the first one is about incorrect thread factory used for shared container timeout, which resulted in JVM waiting for that thread and not exiting as it should. The other issue enables relative URIs in Location header when using redirect feature. Links Tyrus homepage mailing list JIRA Complete list of changes: Bug [TYRUS-333] – Multiple endpoints on one client [TYRUS-334] – When connection is closed by a peer, periodic heartbeat pong is not stopped [TYRUS-336] – ReaderBuffer.getNextChars() keeps blocking a server thread after client has closed the session [TYRUS-338] – JDK client SSL filter needs better synchronization during handshake phase [TYRUS-339] – SSL hostname verification is missing [TYRUS-340] – Test PathParamTest are not stable with JDK client [TYRUS-341] – A control frame inside a stream of continuation frames is treated as the part of the stream [TYRUS-343] – ControlFrameInDataStreamTest does not pass on GF [TYRUS-345] – NPE is thrown, when shared container timeout property in JDK client is not set [TYRUS-346] – IllegalStateException is thrown, when using proxy in JDK client [TYRUS-347] – Introduce better synchronization in JDK client thread pool [TYRUS-348] – When a client and server close connection simultaneously, JDK client throws NPE [TYRUS-356] – Tyrus cannot determine the connection port for a wss URL [TYRUS-357] – Exception thrown in MessageHandler#OnMessage is not caught in @OnError method [TYRUS-359] – Client based on Java 7 Asynchronous IO makes application unexitable Improvement [TYRUS-328] – JDK 1.7 AIO Client container – threads – (setting threadpool, limits, …) [TYRUS-332] – Consolidate shared client properties into one file. [TYRUS-337] – Create an SSL version of Basic Servlet test New Feature [TYRUS-228] – Add client support for HTTP Basic/Digest Task [TYRUS-330] – create/run tests/servlet/basic via wss [TYRUS-335] – [clustering] – introduce RemoteSession and expose them via separate method (not include remote sessions in the getOpenSessions()) [TYRUS-344] – Introduce Client support for HTTP Redirect

  Read the article

• Indentify Codecs & Technical Information About Video Files

  - by DigitalGeekery

  Have you ever wanted to play an audio or video file but didn’t have the proper codec installed? Today we’ll show how to determine codecs, along with a host of other technical details about your media files with MediaInfo. Installation Download and install MediaInfo. You can find the download link at the bottom of the page. Note: When installing MediaInfo there is a recommended software bundle which you can opt out of by selecting Do not install option. Each recommended software choice may be different, like in this example it offers Spyware Terminator. The cool thing though is they use Open Candy which opts you out of the install. Just double check to make sure you’re not installing extra crapware. Using MediaInfo The first time you run MediaInfo it will display the Preferences window. There are various option such as language, output format, and whether or not you want MediaInfo to check for new versions. Click OK. Select a file or folder to analyze by clicking on the File or Folder icons on the left of the application window or by selecting File > Open from the menu. You can also drag and drop a file directly onto the application. MediaInfo will display details of your media file. In Basic view, you’ll see basic information. Notice in the example below the video and audio codecs, along with file size, running time of the media file, and even the application used to create the video file (Writing application).    You can switch to some of the other views by selecting View from the Menu and choosing form the dropdown list.   Sheet View will present the information a bit more clearly. You can see in the example below that the video and audio codec are listing in clearly identified columns. (AVC is often more commonly referred to H.264.)   Tree View is perhaps the most detailed. You can see from the example below the codec used for this AVI file is XviD.   Scrolling down even further you’ll see additional information like video and audio bit rates, frame rate, aspect ratio, and more.   In Basic View (and also in Sheet view) you can click to find a player for your file. In this instance with an MP4 file, it took me to the download page for Quicktime. This is by no means the only media player for this file, but if you are stuck for how to play a media file, this will forward you to a solution that works. You can do the same thing with Video codec. Click Go to the web site of this video codec to find a download.   MediaInfo is a simple but powerful tool that can be used to discover the details of a media file, or just to find a compatible codec. It works with most any video file type and is available for Windows, Mac, and Linux. Some Mac and Linux versions, however, are currently command line only. Download MediaInfo Similar Articles Productive Geek Tips How to Convert Videos to 3GP for Mobile PhonesFix for VLC Skipping and Lagging Playing High-Def Video FilesUsing VLC Player Under VistaUse Your Mac Mini as a Media Server Part 2How to Play .OGM Video Files in Windows Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 2010 World Cup Schedule Boot Snooze – Reboot and then Standby or Hibernate Customize Everything Related to Dates, Times, Currency and Measurement in Windows 7 Google Earth replacement Icon (Icons we like) Build Great Charts in Excel with Chart Advisor tinysong gives a shortened URL for you to post on Twitter (or anywhere)

  Read the article

• Use your iPhone or iPod Touch as a Boxee Remote

  - by DigitalGeekery

  Are you a Boxee user looking for a remote control solution? Well, you might not need to look any further than your pocket. The free Boxee Remote App turns your iPhone or iPod Touch into a a simple and easy-to-use Boxee remote. The Boxee Remote App works over WiFi, so there is no need for to buy or install additional hardware on your PC. Plus, you don’t even need to be within the line of sight for it to work. Using the Boxee Remote App Download the free Boxee Remote App from the App Store and install it on your iPhone or iPod Touch. See download link below. Next, make sure you have Boxee running on your PC. Select the Boxee icon to open the App.   The first time you log in you’ll be greeted by an introduction screen that will explain the two modes. Click Continue. When opened in “Button” mode, you’ll be presented with 4 directional buttons, an “OK” button, and a back arrow button that works like the Esc key does in Boxee. Button mode performs just as a normal remote. Touching the directional buttons moves your on screen selection right, left, up, and down. Tap the OK button to open or select an item. To enter “Gesture” mode, tap the Gesture button along the top of the Screen. Gesture mode works similar to a touch pad or trackball on a laptop. You drag the Boxee icon with your thumb or finger across the screen to move around within Boxee. The icon will turn red while being dragged or touched. Simply tap the icon to select.   The Settings button allows you to manually add or delete a host computer, or adjust the sensitivity of the controls.     If you need to enter text, such as enter logon credentials for an App, the on screen keyboard will pop up. While watching a video you’ll have on-screen Stop and Pause buttons along with a volume slider.   The Boxee Remote App is simple and easy to use. As long as you can connect via WiFi, you can use it to control any instance of Boxee running on any computer on your network. Download the Boxee Remote App Similar Articles Productive Geek Tips Why Wait? Amazing New Add-on Turns Your iPhone into an iPad! [Comic]Getting Started with BoxeeIntegrate Boxee with Media Center in Windows 7Watch Netflix Instant Movies in BoxeeWin a Free iPod Touch in the How-To Geek Facebook Giveaway! TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Out of band Security Update for Internet Explorer 7 Cool Looking Screensavers for Windows SyncToy syncs Files and Folders across Computers on a Network (or partitions on the same drive) If it were only this easy Classic Cinema Online offers 100’s of OnDemand Movies OutSync will Sync Photos of your Friends on Facebook and Outlook

  Read the article

• Ubuntu 12.04 LTS initramfs-tools dependency issue

  - by Mike

  I know this has been asked several times, but each issue and resolution seems different. I've tried almost everything I could think of, but I can't fix this. I have a VM (VMware I think) running 12.04.03 LTS which has stuck dependencies. The VM is on a rented host, running a live system so I don't want to break it (further). uname -a Linux support 3.5.0-36-generic #57~precise1-Ubuntu SMP Thu Jun 20 18:21:09 UTC 2013 x86_64 x86_64 x86_64 GNU/Linux Some more: sudo apt-get update [sudo] password for tracker: Reading package lists... Done Building dependency tree Reading state information... Done You might want to run ‘apt-get -f install’ to correct these. The following packages have unmet dependencies. initramfs-tools : Depends: initramfs-tools-bin (< 0.99ubuntu13.1.1~) but 0.99ubuntu13.3 is installed E: Unmet dependencies. Try using -f. sudo apt-get install -f Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following extra packages will be installed: initramfs-tools The following packages will be upgraded: initramfs-tools 1 upgraded, 0 newly installed, 0 to remove and 2 not upgraded. 2 not fully installed or removed. Need to get 0 B/50.3 kB of archives. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? Y dpkg: dependency problems prevent configuration of initramfs-tools: initramfs-tools depends on initramfs-tools-bin (<< 0.99ubuntu13.1.1~); however: Version of initramfs-tools-bin on system is 0.99ubuntu13.3. dpkg: error processing initramfs-tools (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. dpkg: dependency problems prevent configuration of apparmor: apparmor depends on initramfs-tools; however: Package initramfs-tools is not configured yet. dpkg: error processing apparmor (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates it's a follow-up error from a previous failure. Errors were encountered while processing: initramfs-tools apparmor E: Sub-process /usr/bin/dpkg returned an error code (1) If I look at the policy behind initramfs-tools / bin I get: apt-cache policy initramfs-tools initramfs-tools: Installed: 0.99ubuntu13.1 Candidate: 0.99ubuntu13.3 Version table: 0.99ubuntu13.3 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise-updates/main amd64 Packages *** 0.99ubuntu13.1 0 100 /var/lib/dpkg/status 0.99ubuntu13 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise/main amd64 Packages apt-cache policy initramfs-tools-bin initramfs-tools-bin: Installed: 0.99ubuntu13.3 Candidate: 0.99ubuntu13.3 Version table: *** 0.99ubuntu13.3 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise-updates/main amd64 Packages 100 /var/lib/dpkg/status 0.99ubuntu13 0 500 http://gb.archive.ubuntu.com/ubuntu/ precise/main amd64 Packages So the issue seems to be I have 0.99ubuntu13.3 for initramfs-tools-bin yet 0.99ubuntu13.1 for initramfs-tools, and can't upgrade to 0.99ubuntu13.3. I've performed apt-get clean/autoclean/install -f/upgrade -f many times but they won't resolve. I can think of only 2 other 'solutions': Edit the dpkg dependency list to trick it into doing the installation with a broken dependency. This seems very dodgy and it would be a last resort Downgrade both initramfs-tools and initramfs-tools-bin to 0.99ubuntu13 from the precise/main sources and hope that would get them in step. However I'm not sure if this will be possible, or whether it would introduce more issues. I'm not sure how this situation arise in the first place. /boot was 96% full; it's now 56% full (it's tiny - 64MB ... this is what I got from the hosting company). Can anyone offer advice please?

  Read the article

• What information must never appear in logs?

  - by MainMa

  I'm about to write the company guidelines about what must never appear in logs (trace of an application). In fact, some developers try to include as many information as possible in trace, making it risky to store those logs, and extremely dangerous to submit them, especially when the customer doesn't know this information is stored, because she never cared about this and never read documentation and/or warning messages. For example, when dealing with files, some developers are tempted to trace the names of the files. For example before appending file name to a directory, if we trace everything on error, it will be easy to notice for example that the appended name is too long, and that the bug in the code was to forget to check for the length of the concatenated string. It is helpful, but this is sensitive data, and must never appear in logs. In the same way: Passwords, IP addresses and network information (MAC address, host name, etc.)¹, Database accesses, Direct input from user and stored business data must never appear in trace. So what other types of information must be banished from the logs? Are there any guidelines already written which I can use? ¹ Obviously, I'm not talking about things as IIS or Apache logs. What I'm talking about is the sort of information which is collected with the only intent to debug the application itself, not to trace the activity of untrusted entities. Edit: Thank you for your answers and your comments. Since my question is not too precise, I'll try to answer the questions asked in the comments: What I'm doing with the logs? The logs of the application may be stored in memory, which means either in plain on hard disk on localhost, in a database, again in plain, or in Windows Events. In every case, the concern is that those sources may not be safe enough. For example, when a customer runs an application and this application stores logs in plain text file in temp directory, anybody who has a physical access to the PC can read those logs. The logs of the application may also be sent through internet. For example, if a customer has an issue with an application, we can ask her to run this application in full-trace mode and to send us the log file. Also, some application may sent automatically the crash report to us (and even if there are warnings about sensitive data, in most cases customers don't read them). Am I talking about specific fields? No. I'm working on general business applications only, so the only sensitive data is business data. There is nothing related to health or other fields covered by specific regulations. But thank you to talk about that, I probably should take a look about those fields for some clues about what I can include in guidelines. Isn't it easier to encrypt the data? No. It would make every application much more difficult, especially if we want to use C# diagnostics and TraceSource. It would also require to manage authorizations, which is not the easiest think to do. Finally, if we are talking about the logs submitted to us from a customer, we must be able to read the logs, but without having access to sensitive data. So technically, it's easier to never include sensitive information in logs at all and to never care about how and where those logs are stored.

  Read the article

• How the number of indexes built on a table can impact performances?

  - by Davide Mauri

  We all know that putting too many indexes (I’m talking of non-clustered index only, of course) on table may produce performance problems due to the overhead that each index bring to all insert/update/delete operations on that table. But how much? I mean, we all agree – I think – that, generally speaking, having many indexes on a table is “bad”. But how bad it can be? How much the performance will degrade? And on a concurrent system how much this situation can also hurts SELECT performances? If SQL Server take more time to update a row on a table due to the amount of indexes it also has to update, this also means that locks will be held for more time, slowing down the perceived performance of all queries involved. I was quite curious to measure this, also because when teaching it’s by far more impressive and effective to show to attended a chart with the measured impact, so that they can really “feel” what it means! To do the tests, I’ve create a script that creates a table (that has a clustered index on the primary key which is an identity column) , loads 1000 rows into the table (inserting 1000 row using only one insert, instead of issuing 1000 insert of one row, in order to minimize the overhead needed to handle the transaction, that would have otherwise ), and measures the time taken to do it. The process is then repeated 16 times, each time adding a new index on the table, using columns from table in a round-robin fashion. Test are done against different row sizes, so that it’s possible to check if performance changes depending on row size. The result are interesting, although expected. This is the chart showing how much time it takes to insert 1000 on a table that has from 0 to 16 non-clustered indexes. Each test has been run 20 times in order to have an average value. The value has been cleaned from outliers value due to unpredictable performance fluctuations due to machine activity. The test shows that in a  table with a row size of 80 bytes, 1000 rows can be inserted in 9,05 msec if no indexes are present on the table, and the value grows up to 88 (!!!) msec when you have 16 indexes on it This means a impact on performance of 975%. That’s *huge*! Now, what happens if we have a bigger row size? Say that we have a table with a row size of 1520 byte. Here’s the data, from 0 to 16 indexes on that table: In this case we need near 22 msec to insert 1000 in a table with no indexes, but we need more that 500msec if the table has 16 active indexes! Now we’re talking of a 2410% impact on performance! Now we can have a tangible idea of what’s the impact of having (too?) many indexes on a table and also how the size of a row also impact performances. That’s why the golden rule of OLTP databases “few indexes, but good” is so true! (And in fact last week I saw a database with tables with 1700bytes row size and 23 (!!!) indexes on them!) This also means that a too heavy denormalization is really not a good idea (we’re always talking about OLTP systems, keep it in mind), since the performance get worse with the increase of the row size. So, be careful out there, and keep in mind the “equilibrium” is the key world of a database professional: equilibrium between read and write performance, between normalization and denormalization, between to few and too may indexes. PS Tests are done on a VMWare Workstation 7 VM with 2 CPU and 4 GB of Memory. Host machine is a Dell Precsioni M6500 with i7 Extreme X920 Quad-Core HT 2.0Ghz and 16Gb of RAM. Database is stored on a SSD Intel X-25E Drive, Simple Recovery Model, running on SQL Server 2008 R2. If you also want to to tests on your own, you can download the test script here: Open TestIndexPerformance.sql

  Read the article

• Sprinkle Some Magik on that Java Virtual Machine

  - by Jim Connors

  GE Energy, through its Smallworld subsidiary, has been providing geospatial software solutions to the utility and telco markets for over 20 years.  One of the fundamental building blocks of their technology is a dynamically-typed object oriented programming language called Magik.  Like Java, Magik source code is compiled down to bytecodes that run on a virtual machine -- in this case the Magik Virtual Machine. Throughout the years, GE has invested considerable engineering talent in the support and maintenance of this virtual machine.  At the same time vast energy and resources have been invested in the Java Virtual Machine. The question for GE has been whether to continue to make that investment on its own or to leverage massive effort provided by the Java community? Utilizing the Java Virtual Machine instead of maintaining its own virtual machine would give GE more opportunity to focus on application solutions.   At last count, there are dozens, perhaps hundreds of examples of programming languages that have been hosted atop the Java Virtual Machine.  Prior to the release of Java 7, that effort, although certainly possible, was generally less than optimal for languages like Magik because of its dynamic nature.  Java, as a statically typed language had little use for this capability.  In the quest to be a more universal virtual machine, Java 7, via JSR-292, introduced a new bytecode called invokedynamic.  In short, invokedynamic affords a more flexible method call mechanism needed by dynamic languages like Magik. With this new capability GE Energy has succeeded in hosting their Magik environment on top of the Java Virtual Machine.  So you may ask, why would GE wish to do such a thing?  The benefits are many: Competitors to GE Energy claimed that the Magik environment was proprietary.  By utilizing the Java Virtual Machine, that argument gets put to bed.  JVM development is done in open source, where contributions are made world-wide by all types of organizations and individuals. The unprecedented wealth of class libraries and applications written for the Java platform are now opened up to Magik/JVM platform as first class citizens. In addition, the Magik/JVM solution vastly increases the developer pool to include the 9 million Java developers -- the largest developer community on the planet. Applications running on the JVM showed substantial performance gains, in some cases as much as a 5x speed up over the original Magik platform. Legacy Magik applications can still run on the original platform.  They can be seamlessly migrated to run on the JVM by simply recompiling the source code. GE can now leverage the huge Java community.  Undeniably the best virtual machine ever created, hundreds if not thousands of world class developers continually improve, poke, prod and scrutinize all aspects of the Java platform.  As enhancements are made, GE automatically gains access to these. As Magik has little in the way of support for multi-threading, GE will benefit from current and future Java offerings (e.g. lambda expressions) that aim to further facilitate multi-core/multi-threaded application development. As the JVM is available for many more platforms, it broadens the reach of Magik, including the potential to run on a class devices never envisioned just a few short years ago.  For example, Java SE compatible runtime environments are available for popular embedded ARM/Intel/PowerPC configurations that could theoretically host this software too. As compared to other JVM language projects, the Magik integration differs in that it represents a serious commercial entity betting a sizable part of its business on the success of this effort.  Expect to see announcements not only from General Electric, but other organizations as they realize the benefits of utilizing the Java Virtual Machine.

  Read the article

• Slow wired internet connection on Realtek RTL8168-8111 (Rev 6)

  - by Mark

  I keep on seeing issues people are having with their wireless. I am having an issue with being wired into my router. I installed Ubuntu 11.10 the other day, on my custom PC. The motherboard I have installed on this PC is an ASUS P8H61-M. The issue I am having is with my speed. I have a dual boot, windows 7 and the new Ubuntu. On my Windows install I am getting test speeds from Speakeasy at 17Mbps and actual downloads around 2-3MB/s. With Ubuntu, I am getting test speeds from Speakeasy at 1.14Mbps and actual downloads around 60KB/s. I have disabled IPv6 and am no using GoogleDNS for my DNS, but it hasn't resolved the issue. I have scanned my router (WRT54GS Linksys) to disable IPv6 connections, and I am not seeing any option for that. I cannot figure out why I am getting such sluggish internet connection. Any help to resolve would be great! I performed an iconfig -a with these results: mark@Mark-ASUS:~$ ifconfig -a eth0 Link encap:Ethernet HWaddr f4:6d:04:d1:2c:4e inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::f66d:4ff:fed1:2c4e/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:21888 errors:0 dropped:21888 overruns:0 frame:21888 TX packets:21068 errors:0 dropped:90 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:26348337 (26.3 MB) TX bytes:2217140 (2.2 MB) Interrupt:46 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:952 (952.0 B) TX bytes:952 (952.0 B) My specs are: mark@Mark-ASUS:~$ sudo lspci -nn 04:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 06) 06:00.0 PCI bridge [0604]: ASMedia Technology Inc. Device [1b21:1080] (rev 01) udev information: KERNEL[11.351405] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 UDEV [11.363905] add /devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 (net) UDEV_LOG=3 ACTION=add DEVPATH=/devices/pci0000:00/0000:00:1c.2/0000:04:00.0/net/eth0 SUBSYSTEM=net INTERFACE=eth0 IFINDEX=2 SEQNUM=1542 ID_VENDOR_FROM_DATABASE=Realtek Semiconductor Co., Ltd. ID_MODEL_FROM_DATABASE=RTL8111/8168B PCI Express Gigabit Ethernet controller ID_BUS=pci ID_VENDOR_ID=0x10ec ID_MODEL_ID=0x8168 ID_MM_CANDIDATE=1 dmesg information: [ 2.855982] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 2.856366] r8169 0000:04:00.0: eth0: RTL8168b/8111b at 0xffffc9000064c000, f4:6d:04:d1:2c:4e, XID 0c900800 IRQ 46 [ 12.540956] r8169 0000:04:00.0: eth0: link down [ 12.540961] r8169 0000:04:00.0: eth0: link down [ 12.541173] ADDRCONF(NETDEV_UP): eth0: link is not ready I took out a lot of information that did not pertain to eth0, because the previous edits wouldn't save. If I need any more information, let me know. I would love to get this resolved. The other issue I am noticing is sometimes my connection disconnects all together, for about a minute, then it reconnects.

  Read the article

• Windows Azure Recipe: Consumer Portal

  - by Clint Edmonson

  Nearly every company on the internet has a web presence. Many are merely using theirs for informational purposes. More sophisticated portals allow customers to register their contact information and provide some level of interaction or customer support. But as our understanding of how consumers use the web increases, the more progressive companies are taking advantage of social web and rich media delivery to connect at a deeper level with the consumers of their goods and services. Drivers Cost reduction Scalability Global distribution Time to market Solution Here’s a sketch of how a Windows Azure Consumer Portal might be built out: Ingredients Web Role – this will host the core of the solution. Each web role is a virtual machine hosting an application written in ASP.NET (or optionally php, or node.js). The number of web roles can be scaled up or down as needed to handle peak and non-peak traffic loads. Database – every modern web application needs to store data. SQL Azure databases look and act exactly like their on-premise siblings but are fault tolerant and have data redundancy built in. Access Control (optional) – if identity needs to be tracked within the solution, the access control service combined with the Windows Identity Foundation framework provides out-of-the-box support for several social media platforms including Windows LiveID, Google, Yahoo!, Facebook. It also has a provider model to allow integration with other platforms as well. Caching (optional) – for sites with high traffic with lots of read-only data and lists, the distributed in-memory caching service can be used to cache and serve up static data at higher scale and speed than direct database requests. It can also be used to manage user session state. Blob Storage (optional) – for sites that serve up unstructured data such as documents, video, audio, device drivers, and more. The data is highly available and stored redundantly across data centers. Each entry in blob storage is provided with it’s own unique URL for direct access by the browser. Content Delivery Network (CDN) (optional) – for sites that service users around the globe, the CDN is an extension to blob storage that, when enabled, will automatically cache frequently accessed blobs and static site content at edge data centers around the world. The data can be delivered statically or streamed in the case of rich media content. Training Labs These links point to online Windows Azure training labs where you can learn more about the individual ingredients described above. (Note: The entire Windows Azure Training Kit can also be downloaded for offline use.) Windows Azure (16 labs) Windows Azure is an internet-scale cloud computing and services platform hosted in Microsoft data centers, which provides an operating system and a set of developer services which can be used individually or together. It gives developers the choice to build web applications; applications running on connected devices, PCs, or servers; or hybrid solutions offering the best of both worlds. New or enhanced applications can be built using existing skills with the Visual Studio development environment and the .NET Framework. With its standards-based and interoperable approach, the services platform supports multiple internet protocols, including HTTP, REST, SOAP, and plain XML SQL Azure (7 labs) Microsoft SQL Azure delivers on the Microsoft Data Platform vision of extending the SQL Server capabilities to the cloud as web-based services, enabling you to store structured, semi-structured, and unstructured data. Windows Azure Services (9 labs) As applications collaborate across organizational boundaries, ensuring secure transactions across disparate security domains is crucial but difficult to implement. Windows Azure Services provides hosted authentication and access control using powerful, secure, standards-based infrastructure. See my Windows Azure Resource Guide for more guidance on how to get started, including links web portals, training kits, samples, and blogs related to Windows Azure.

  Read the article

• vmware player xorg driver broke after ubuntu 12.04 LTS automatic system update on 06/07/2014

  - by user291828

  I am running Ubuntu 12.04 LTS as a virtual machine on a Windows 7 host using vmware player 6.0.2. On Sat. 06/07/2014, Ubuntu performed an automatic system update as it does regularly, however after reboot, the display driver seems to be broken which causes the screen to split into many identical panels. This pretty much rendered the VM unusable. Below is the log entry for that update from /var/log/apt/history.log It appears that at least one of these updates have caused this problem. The exact same problem has been reported on the vmware forum as well, see https://communities.vmware.com/message/2388776#2388776 So far I have not been able so find a solution. Content in /var/log/apt/history.log Start-Date: 2014-06-07 15:04:46 Commandline: aptdaemon role='role-commit-packages' sender=':1.65' Install: linux-headers-3.2.0-64:amd64 (3.2.0-64.97), linux-image-3.2.0-64-generic:amd64 (3.2.0-64.97), linux-headers-3.2.0-64-generic:amd64 (3.2.0-64.97) Upgrade: iproute:amd64 (20111117-1ubuntu2.1, 20111117-1ubuntu2.3), libknewstuff3-4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdeclarative5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libnepomukquery4a:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libgnutls-openssl27:amd64 (2.12.14-5ubuntu3.7, 2.12.14-5ubuntu3.8), libthreadweaver4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdecore5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libnepomukutils4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libktexteditor4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), linux-generic:amd64 (3.2.0.63.75, 3.2.0.64.76), libkmediaplayer4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkrosscore4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libgnutls26:amd64 (2.12.14-5ubuntu3.7, 2.12.14-5ubuntu3.8), libgnutls26:i386 (2.12.14-5ubuntu3.7, 2.12.14-5ubuntu3.8), libsolid4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libnepomuk4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdnssd4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkparts4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), kdoctools:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libssl-dev:amd64 (1.0.1-4ubuntu5.13, 1.0.1-4ubuntu5.14), libssl-doc:amd64 (1.0.1-4ubuntu5.13, 1.0.1-4ubuntu5.14), libkidletime4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), linux-headers-generic:amd64 (3.2.0.63.75, 3.2.0.64.76), linux-image-generic:amd64 (3.2.0.63.75, 3.2.0.64.76), libkcmutils4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkfile4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkpty4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkntlm4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libplasma3:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkemoticons4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), kdelibs-bin:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdewebkit5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkjsembed4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkio5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkjsapi4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), openssl:amd64 (1.0.1-4ubuntu5.13, 1.0.1-4ubuntu5.14), kdelibs5-data:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), linux-libc-dev:amd64 (3.2.0-63.95, 3.2.0-64.97), libkde3support4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libknotifyconfig4:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), kdelibs5-plugins:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkhtml5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdeui5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libkdesu5:amd64 (4.8.5-0ubuntu0.2, 4.8.5-0ubuntu0.3), libssl1.0.0:amd64 (1.0.1-4ubuntu5.13, 1.0.1-4ubuntu5.14), libssl1.0.0:i386 (1.0.1-4ubuntu5.13, 1.0.1-4ubuntu5.14) End-Date: 2014-06-07 15:09:08

  Read the article

• Schizophrenic Ubuntu 12.10-12.04: Atheros 922 PCI WIFI is disabled in Unity but enabled in terminal - How to getit to work?

  - by zewone

  I am trying to get my PCI Wireless Atheros 922 card to work. It is disabled in Unity: both the network utility and the desktop (see screenshot http://www.amisdurailhalanzy.be/Screenshot%20from%202012-10-25%2013:19:54.png) I tried many different advises on many different forums. Installed 12.10 instead of 12.04, enabled all interfaces... etc. I have read about the aht9 driver... The terminal shows no hw or sw lock for the Atheros card, nevertheless, it is still disabled. Nothing worked so far, the card is still disabled. Any help is much appreciated. Here are more tech details: myuser@adri1:~$ sudo lshw -C network *-network:0 DISABLED description: Wireless interface product: AR922X Wireless Network Adapter vendor: Atheros Communications Inc. physical id: 2 bus info: pci@0000:03:02.0 logical name: wlan1 version: 01 serial: 00:18:e7:cd:68:b1 width: 32 bits clock: 66MHz capabilities: pm bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.5.0-17-generic firmware=N/A latency=168 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:d8000000-d800ffff *-network:1 description: Ethernet interface product: VT6105/VT6106S [Rhine-III] vendor: VIA Technologies, Inc. physical id: 6 bus info: pci@0000:03:06.0 logical name: eth0 version: 8b serial: 00:11:09:a3:76:4a size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.5.0 duplex=half latency=32 link=no maxlatency=8 mingnt=3 multicast=yes port=MII speed=10Mbit/s resources: irq:18 ioport:d300(size=256) memory:d8013000-d80130ff *-network DISABLED description: Wireless interface physical id: 1 bus info: usb@1:8.1 logical name: wlan0 serial: 00:11:09:51:75:36 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2500usb driverversion=3.5.0-17-generic firmware=N/A link=no multicast=yes wireless=IEEE 802.11bg myuser@adri1:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy1: Wireless LAN Soft blocked: no Hard blocked: yes 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no myuser@adri1:~$ dmesg | grep wlan0 [ 15.114235] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready myuser@adri1:~$ dmesg | egrep 'ath|firm' [ 14.617562] ath: EEPROM regdomain: 0x30 [ 14.617568] ath: EEPROM indicates we should expect a direct regpair map [ 14.617572] ath: Country alpha2 being used: AM [ 14.617575] ath: Regpair used: 0x30 [ 14.637778] ieee80211 phy0: >Selected rate control algorithm 'ath9k_rate_control' [ 14.639410] Registered led device: ath9k-phy0 myuser@adri1:~$ dmesg | grep wlan1 [ 15.119922] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready myuser@adri1:~$ lspci -nn | grep 'Atheros' 03:02.0 Network controller [0280]: Atheros Communications Inc. AR922X Wireless Network Adapter [168c:0029] (rev 01) myuser@adri1:~$ sudo ifconfig eth0 Link encap:Ethernet HWaddr 00:11:09:a3:76:4a inet addr:192.168.2.2 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::211:9ff:fea3:764a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5457 errors:0 dropped:0 overruns:0 frame:0 TX packets:2548 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3425684 (3.4 MB) TX bytes:282192 (282.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:590 errors:0 dropped:0 overruns:0 frame:0 TX packets:590 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:53729 (53.7 KB) TX bytes:53729 (53.7 KB) myuser@adri1:~$ sudo iwconfig wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on lo no wireless extensions. eth0 no wireless extensions. wlan1 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off myuser@adri1:~$ lsmod | grep "ath9k" ath9k 116549 0 mac80211 461161 3 rt2x00usb,rt2x00lib,ath9k ath9k_common 13783 1 ath9k ath9k_hw 376155 2 ath9k,ath9k_common ath 19187 3 ath9k,ath9k_common,ath9k_hw cfg80211 175375 4 rt2x00lib,ath9k,mac80211,ath myuser@adri1:~$ iwlist scan wlan0 Failed to read scan data : Network is down lo Interface doesn't support scanning. eth0 Interface doesn't support scanning. wlan1 Failed to read scan data : Network is down myuser@adri1:~$ lsb_release -d Description: Ubuntu 12.10 myuser@adri1:~$ uname -mr 3.5.0-17-generic i686  Any help much appreciated... Thanks, Philippe

  Read the article

• Ask HTG: How Can I Check the Age of My Windows Installation?

  - by Jason Fitzpatrick

  Curious about when you installed Windows and how long you’ve been chugging along without a system refresh? Read on as we show you a simple way to see how long-in-the-tooth your Windows installation is. Dear How-To Geek, It feels like it has been forever since I installed Windows 7 and I’m starting to wonder if some of the performance issues I’m experiencing have something to do with how long ago it was installed. It isn’t crashing or anything horrible, mind you, it just feels slower than it used to and I’m wondering if I should reinstall it to wipe the slate clean. Is there a simple way to determine the original installation date of Windows on its host machine? Sincerely, Worried in Windows Although you only intended to ask one question, you actually asked two. Your direct question is an easy one to answer (how to check the Windows installation date). The indirect question is, however, a little trickier (if you need to reinstall Windows to get a performance boost). Let’s start off with the easy one: how to check your installation date. Windows includes a handy little application just for the purposes of pulling up system information like the installation date, among other things. Open the Start Menu and type cmd in the run box (or, alternatively, press WinKey+R to pull up the run dialog and enter the same command). At the command prompt, type systeminfo.exe Give the application a moment to run; it takes around 15-20 seconds to gather all the data. You’ll most likely need to scroll back up in the console window to find the section at the top that lists operating system stats. What you care about is Original Install Date: We’ve been running the machine we tested the command on since August 23 2009. For the curious, that’s one month and a day after the initial public release of Windows 7 (after we were done playing with early test releases and spent a month mucking around in the guts of Windows 7 to report on features and flaws, we ran a new clean installation and kept on trucking). Now, you might be asking yourself: Why haven’t they reinstalled Windows in all that time? Haven’t things slowed down? Haven’t they upgraded hardware? The truth of the matter is, in most cases there’s no need to completely wipe your computer and start from scratch to resolve issues with Windows and, if you don’t bog your system down with unnecessary and poorly written software, things keep humming along. In fact, we even migrated this machine from a traditional mechanical hard drive to a newer solid-state drive back in 2011. Even though we’ve tested piles of software since then, the machine is still rather clean because 99% of that testing happened in a virtual machine. That’s not just a trick for technology bloggers, either, virtualizing is a handy trick for anyone who wants to run a rock solid base OS and avoid the bog-down-and-then-refresh cycle that can plague a heavily used machine. So while it might be the case that you’ve been running Windows 7 for years and heavy software installation and use has bogged your system down to the point a refresh is in order, we’d strongly suggest reading over the following How-To Geek guides to see if you can’t wrangle the machine into shape without a total wipe (and, if you can’t, at least you’ll be in a better position to keep the refreshed machine light and zippy): HTG Explains: Do You Really Need to Regularly Reinstall Windows? PC Cleaning Apps are a Scam: Here’s Why (and How to Speed Up Your PC) The Best Tips for Speeding Up Your Windows PC Beginner Geek: How to Reinstall Windows on Your Computer Everything You Need to Know About Refreshing and Resetting Your Windows 8 PC Armed with a little knowledge, you too can keep a computer humming along until the next iteration of Windows comes along (and beyond) without the hassle of reinstalling Windows and all your apps.         

  Read the article

• PowerShell: Read Excel to Create Inserts

  - by BuckWoody

  I’m writing a series of articles on how to migrate “departmental” data into SQL Server. I also hold workshops on the entire process – from discovering that the data exists to the modeling process and then how to design the Extract, Transform and Load (ETL) process. Finally I write about (and teach) a few methods on actually moving the data. One of those options is to use PowerShell. There are a lot of ways even with that choice, but the one I show is to read two columns from the spreadsheet and output statements that would insert the data using a stored procedure. Of course, you could re-write this as INSERT statements, out to a text file for bcp, or even use a database connection in the script to move the data directly from Excel into SQL Server. This snippet won’t run on your system, of course – it assumes a Microsoft Office Excel 2007 spreadsheet located at c:\temp called VendorList.xlsx. It looks for a tab in that spreadsheet called Vendors. The statement that does the writing just uses one column: Vendor Code. Here’s the breakdown of what I’m doing: In the first block, I connect to Microsoft Office Excel. That connection string is specific to Excel 2007, so if you need a different version you’ll need to look that up. In the second block I set up a selection from the entire spreadsheet based on that tab. Note that if you’re only after certain data you shouldn’t get the whole spreadsheet – that’s just good practice. In the next block I create the text I want, inserting the Vendor Code field as I go. Finally I close the connection. Enjoy! $ExcelConnection= New-Object -com "ADODB.Connection" $ExcelFile="c:\temp\VendorList.xlsx" $ExcelConnection.Open("Provider=Microsoft.ACE.OLEDB.12.0;` Data Source=$ExcelFile;Extended Properties=Excel 12.0;") $strQuery="Select * from [Vendors$]" $ExcelRecordSet=$ExcelConnection.Execute($strQuery) do { Write-Host "EXEC sp_InsertVendors '" $ExcelRecordSet.Fields.Item("Vendor Code").Value "'" $ExcelRecordSet.MoveNext()} Until ($ExcelRecordSet.EOF) $ExcelConnection.Close() Script Disclaimer, for people who need to be told this sort of thing: Never trust any script, including those that you find here, until you understand exactly what it does and how it will act on your systems. Always check the script on a test system or Virtual Machine, not a production system. All scripts on this site are performed by a professional stunt driver on a closed course. Your mileage may vary. Void where prohibited. Offer good for a limited time only. Keep out of reach of small children. Do not operate heavy machinery while using this script. If you experience blurry vision, indigestion or diarrhea during the operation of this script, see a physician immediately. Share this post: email it! | bookmark it! | digg it! | reddit! | kick it! | live it!

  Read the article

• apt-get upgrade stuck at the same package

  - by decibyte

  Current status I've started to suspect this is not an Ubuntu issue, but related to the internet connection here at my work. Until I'm sure, Im leaving my question below: Original question I'm stuck, can't upgrade my system. Running sudo apt-get upgrade gives me the following: mmm@alalunga:~$ sudo apt-get upgrade Reading package lists... Done Building dependency tree Reading state information... Done The following packages have been kept back: ginn libgrip0 linux-generic-pae linux-headers-generic-pae linux-image-generic-pae The following packages will be upgraded: apport apport-gtk bind9-host build-essential dhcp3-client dhcp3-common dnsutils eog evince evince-common firefox firefox-branding firefox-dbg firefox-globalmenu firefox-gnome-support firefox-locale-en gimp gimp-data gir1.2-totem-1.0 glib-networking glib-networking-common glib-networking-services gnupg gpgv icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-6-plugin icedtea-netx icedtea-netx-common icedtea-plugin isc-dhcp-client isc-dhcp-common libapache2-mod-php5 libart-2.0-2 libbind9-80 libdns81 libevince3-3 libgimp2.0 libisc83 libisccc80 libisccfg82 liblwres80 libssl-dev libssl-doc libssl1.0.0 libtotem0 linux-firmware linux-libc-dev openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib openssl php-pear php5-cli php5-common php5-curl php5-dev php5-gd php5-mysql php5-xsl policykit-1-gnome python-apport python-django python-gst0.10 python-problem-report resolvconf thunderbird thunderbird-globalmenu thunderbird-gnome-support totem totem-common totem-mozilla totem-plugins xserver-xorg-input-synaptics 74 upgraded, 0 newly installed, 0 to remove and 5 not upgraded. Need to get 317 MB/327 MB of archives. After this operation, 1.481 kB of additional disk space will be used. Do you want to continue [Y/n]? Get:1 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:2 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:3 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:4 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:5 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:6 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] Get:7 http://archive.ubuntu.com/ubuntu/ precise-updates/main openjdk-6-jre-headless i386 6b24-1.11.4-1ubuntu0.12.04.1 [27,3 MB] 9% [7 openjdk-6-jre-headless 27,3 MB/27,3 MB 100%] It keeps downloading the package openjdk-6-jre-headless, then does nothing for a while (hanging on what's the last line above), then download the package again. It's at its 13th download attempt at the moment of writing. The actual downloads seem to be done just fine, but whatever it does after downloading seems to be failing. I tried removing openjdk-6, but then it wanted to install openjdk-7 instead, with the same result, hanging at openjdk-7-jre-headless instead. I also tried changing servers from my local (Danish) to the main server. No luck. It's also keeping me from upgrading alle the other packages. What to do? Update After following instructions in the answer by @lpanebr, it is now stuck at the linux-firmware package. So, maybe it's a more general problem than being related to specific package(s)? Although it did download some packages without problems before getting stuck at linux-firmware.

  Read the article

• Five Key Trends in Enterprise 2.0 for 2011

  - by kellsey.ruppel(at)oracle.com

  We recently sat down with Andy MacMillan, an industry veteran and vice president of product management for Enterprise 2.0 at Oracle, to get his take on the year ahead in Enterprise 2.0 (E2.0). He offered us his five predictions about the ways he believes E2.0 technologies will transform business in 2011. 1. Forward-thinking organizations will achieve an unprecedented level of organizational awareness. Enterprise 2.0 and Web 2.0 technologies have already transformed the ways customers, employees, partners, and suppliers communicate and stay informed. But this year we are anticipating that organizations will go to the next step and integrate social activities with business applications to deliver rich contextual "activity streams." Activity streams are a new way for enterprise users to get relevant information as quickly as it happens, by navigating to that information in context directly from their portal. We don't mean syndicating social activities limited to a single application. Instead, we believe back-office systems will be combined with social media tools to drive how users make informed business decisions in brand new ways. For example, an account manager might log into the company portal and automatically receive notification that colleagues are closing business around a certain product in his market segment. With a single click, he can reach out instantly to these colleagues via social media and learn from their successes to drive new business opportunities in his own area. 2. Online customer engagement will become a high priority for CMOs. A growing number of chief marketing officers (CMOs) have created a new direct report called "head of online"--a senior marketing executive responsible for all engagements with customers and prospects via the Web, mobile, and social media. This new field has been dubbed "Web experience management" or "online customer engagement" by firms and analyst organizations. It is likely to rapidly increase demand for a host of new business objectives and metrics from Web content management solutions. As companies interface with customers more and more over the Web, Web experience management solutions will help deliver more targeted interactions to ensure increased customer loyalty while meeting sales and business objectives. 3. Real composite applications will be widely adopted. We expect organizations to move from the concept of a single "uber-portal" that encompasses all the necessary features to a more modular, component-based concept for composite applications. This approach is now possible as IT and power users are empowered to assemble new, purpose-built composite applications quickly from existing components. 4. Records management will drive ECM consolidation. We continue to see a significant shift in the approach to records management. Several years ago initiatives were focused on overlaying records management across a set of electronic repositories and physical storage locations. We believe federated records management will continue, but we also expect to see records management driving conversations around single-platform content management consolidation. 5. Organizations will demand ECM at extreme scale. We have already seen a trend within IT organizations to provide a common, highly scalable infrastructure to consolidate and support content and information needs. But as data sizes grow exponentially, ECM at an extreme scale is likely to spread at unprecedented speeds this year. This makes sense as regulations and transparency requirements rise. The model in which ECM and lightweight CMS systems provide basic content services such as check-in, update, delete, and search has converged around a set of industry best practices and has even been coded into new industry standards such as content management interoperability services. As these services converge and the demand for them accelerates, organizations are beginning to rationalize investments into a single, highly scalable infrastructure. Is your organization ready for Enterprise 2.0 in 2011? Learn more.

  Read the article

• Access Control Service: Transitioning between Active and Passive Scenarios

  - by Your DisplayName here!

  As I mentioned in my last post, ACS features a number of ways to transition between protocol and token types. One not so widely known transition is between passive sign ins (browser) and active service consumers. Let’s see how this works. We all know the usual WS-Federation handshake via passive redirect. But ACS also allows driving the sign in process yourself via specially crafted WS-Federation query strings. So you can use the following URL to sign in using LiveID via ACS. ACS will then redirect back to the registered reply URL in your application: GET /login.srf?   wa=wsignin1.0&   wtrealm=https%3a%2f%2faccesscontrol.windows.net%2f&   wreply=https%3a%2f%2fleastprivilege.accesscontrol.windows.net%3a443%2fv2%2fwsfederation&   wp=MBI_FED_SSL&   wctx=pr%3dwsfederation%26rm%3dhttps%253a%252f%252froadie%252facs2rp%252frest%252f The wsfederation bit in the wctx parameter indicates, that the response to the token request will be transmitted back to the relying party via a POST. So far so good – but how can an active client receive that token now? ACS knows an alternative way to send the token request response. Instead of doing the redirect back to the RP, it emits a page that in turn echoes the token response using JavaScript’s window.external.notify. The URL would look like this: GET /login.srf?   wa=wsignin1.0&   wtrealm=https%3a%2f%2faccesscontrol.windows.net%2f&   wreply=https%3a%2f%2fleastprivilege.accesscontrol.windows.net%3a443%2fv2%2fwsfederation&   wp=MBI_FED_SSL&   wctx=pr%3djavascriptnotify%26rm%3dhttps%253a%252f%252froadie%252facs2rp%252frest%252f ACS would then render a page that contains the following script block: <script type="text/javascript">     try{         window.external.Notify('token_response');     }     catch(err){         alert("Error ACS50021: windows.external.Notify is not registered.");     } </script> Whereas token_response is a JSON encoded string with the following format: {   "appliesTo":"...",   "context":null,   "created":123,   "expires":123,   "securityToken":"...",   "tokenType":"..." } OK – so how does this all come together now? As an active client (Silverlight, WPF, WP7, WinForms etc). application, you would host a browser control and use the above URL to trigger the right series of redirects. All the browser controls support one way or the other to register a callback whenever the window.external.notify function is called. This way you get the JSON string from ACS back into the hosting application – and voila you have the security token. When you selected the SWT token format in ACS – you can use that token e.g. for REST services. When you have selected SAML, you can use the token e.g. for SOAP services. In the next post I will show how to retrieve these URLs from ACS and a practical example using WPF.

  Read the article

• Wireless doesn't work on a Broadcom BCM4312

  - by Boderick

  As stated, I've just upgraded to 12.04 and my Dell Inspiron 1545 isn't recognising its wireless card and I was wondering if anybody could help? Edit: Okay, so I found the wireless card by using lspci -vvv and it returned this: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) Subsystem: Dell Wireless 1397 WLAN Mini-Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast TAbort- SERR- Kernel modules: ssb lsmod Module Size Used by dm_crypt 22528 0 joydev 17393 0 dell_wmi 12601 0 sparse_keymap 13658 1 dell_wmi dell_laptop 13671 0 dcdbas 14098 1 dell_laptop psmouse 72919 0 uvcvideo 67203 0 serio_raw 13027 0 videodev 86588 1 uvcvideo snd_hda_codec_idt 60251 1 mac_hid 13077 0 snd_hda_intel 32765 5 snd_hda_codec 109562 2 snd_hda_codec_idt,snd_hda_intel snd_hwdep 13276 1 snd_hda_codec parport_pc 32114 0 rfcomm 38139 0 bnep 17830 2 ppdev 12849 0 snd_pcm 80845 3 snd_hda_intel,snd_hda_codec bluetooth 158438 10 rfcomm,bnep snd_seq_midi 13132 0 snd_rawmidi 25424 1 snd_seq_midi snd_seq_midi_event 14475 1 snd_seq_midi snd_seq 51567 2 snd_seq_midi,snd_seq_midi_event snd_timer 28931 2 snd_pcm,snd_seq snd_seq_device 14172 3 snd_seq_midi,snd_rawmidi,snd_seq binfmt_misc 17292 1 snd 62064 18 snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 14635 1 snd snd_page_alloc 14108 2 snd_hda_intel,snd_pcm lp 17455 0 parport 40930 3 parport_pc,ppdev,lp sky2 53628 0 ums_realtek 17920 0 uas 17699 0 i915 414603 3 wmi 18744 1 dell_wmi drm_kms_helper 45466 1 i915 drm 197692 4 i915,drm_kms_helper i2c_algo_bit 13199 1 i915 video 19068 1 i915 usb_storage 39646 1 ums_realtek ifconfig -a eth0 Link encap:Ethernet HWaddr 00:23:ae:24:71:45 inet addr:192.168.1.158 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::223:aeff:fe24:7145/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14340 errors:0 dropped:0 overruns:0 frame:0 TX packets:10191 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:15403754 (15.4 MB) TX bytes:1262570 (1.2 MB) Interrupt:18 ham0 Link encap:Ethernet HWaddr 7a:79:05:2d:b0:f7 inet addr:5.45.176.247 Bcast:5.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:5ff:fe2d:b0f7/64 Scope:Link inet6 addr: 2620:9b::52d:b0f7/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:179 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:27480 (27.4 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:433 errors:0 dropped:0 overruns:0 frame:0 TX packets:433 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:60051 (60.0 KB) TX bytes:60051 (60.0 KB) iwconfig lo no wireless extensions. ham0 no wireless extensions. eth0 no wireless extensions. the results for sudo lshw -class network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:0c:00.0 logical name: eth1 version: 01 serial: 00:22:5f:77:1f:e6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f69fc000-f69fffff *-network description: Ethernet interface product: 88E8040 PCI-E Fast Ethernet Controller vendor: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 13 serial: 00:23:ae:24:71:45 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.158 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:45 memory:f68fc000-f68fffff ioport:de00(size=256) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:05:2d:b0:f7 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.45.176.247 link=yes multicast=yes port=twisted pair speed=10Mbit/s and the results of rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes

  Read the article

• Cannot Mount USB 3.0 Hard Disk ?!!

  - by Tenken

  Hi, I have a USB 3.0 external hard disk which I am unable to mount. The entry appears in the "lsusb" command, but I do not exactly understand how to mount it. This is the output for my lsusb command. "ASMedia Technology Inc." is the USB 3.0 device. I would appreciate some help in mounting and accessing the hard disk. This the relevant output of my "lsusb -v" : Bus 009 Device 002: ID 174c:5106 ASMedia Technology Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x174c ASMedia Technology Inc. idProduct 0x5106 bcdDevice 0.01 iManufacturer 2 ASMedia iProduct 3 AS2105 iSerial 1 00000000000000000000 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.35-28-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:04:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0503 highspeed power enable connect Port 4: 0000.0503 highspeed power enable connect Device Status: 0x0003 Self Powered Remote Wakeup Enabled This is the error given when I try to mount the hard drive: shinso@shinso-IdeaPad:~$ sudo mount /dev/sdb /mnt [sudo] password for shinso: mount: /dev/sdb: unknown device This the output of "dmesg|tail": [30062.774178] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [30535.800977] usb 9-4: USB disconnect, address 3 [30659.237342] Valid eCryptfs headers not found in file header region or xattr region [30659.237351] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31259.268310] Valid eCryptfs headers not found in file header region or xattr region [31259.268313] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31860.059058] Valid eCryptfs headers not found in file header region or xattr region [31860.059062] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [32465.220590] Valid eCryptfs headers not found in file header region or xattr region [32465.220593] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO I am using Ubuntu 10.10 (64 bit). Any help is appreciated.

  Read the article

• How to get faster graphics in KVM? VNC is painfully slow with Haiku OS guest, Spice won't install and SDL doesn't work

  - by Don Quixote

  I've been coming up to speed on the Haiku operating system, an Open Source clone of BeOS 5 Pro. I'm using an Apple MacBook Pro as my development machine. Apple's BootCamp BIOS does not support more than four partitions on the internal hard drive. While I can set up extended and logical partitions, doing so will prevent any of the installed operating systems from booting. To run Haiku directly on the iron, I boot it off a USB stick. Using external storage is also helpful because I am perpetually out of filesystem space. While VirtualBox is documented to allow access to physical drives, I could not actually get it to work. Also VirtualBox can only use one of the host CPU's cores. While VB guests can be configured for more than one CPU, they are only emulated. A full build of the Haiku OS takes 4.5 under VB. I had the hope of reducing build times by using KVM instead, but it's not working nearly as well as VirtualBox did. The Linux Kernel Virtual Machine is broken in all manner of fundamental ways as seen from Haiku. But I'm a coder; maybe I could contribute to fixing some of those problems. The first problem I've got is that Haiku's video in virt-manager is quite painfully slow. When I drag Haiku windows around the desktop, they lag quite far behind where my mouse is. It's quite difficult to move a window to a precise position on the screen. Just imagine that the mouse was connected to the window title bar with a really stretchy spring. Also Haiku's mouse lags quite far behind where I have moved it. I found lots of Personal Package Archives that enable Spice from QEMU / KVM at the Ubuntu Personal Package Arhives. I tried a few of the PPAs but none of them worked; with one of them, the command "add-apt-repository" crashed with a traceback. There is a Wiki page about Spice, but it says that it only works on 64-bit. My Early 2006 MacBook Pro is 32-bit. Its Apple Model Identifier is MacBookPro1,1; these use Core Duos NOT Core 2 Duos. I don't mind building a source deb for 32-bit if I can expect it to work. Is there some reason that Spice should be 64-bit only? Does it need features of the x86_64 Instruction Set Architecture that x86 does not have? When I try using SDL from virt-manager, the configuration for Local SDL Window says "Xauth: /home/mike/.Xauthority". When I try to start my guest, virt-manager emits an error. When I Googled the error message, the usual solution was to make ~/.Xauthority readible. However, .Xauthorty does not exist in my home directory. Instead I have a $XAUTHORITY environment variable. There is no way to configure SDL in virt-manager to use $XAUTHORITY instead of ~/.Xauthority. Neither does it work to copy the value of $XAUTHORITY into the file. I am ready to scream, because I've been five fscking days trying to make KVM work for Haiku development. There is a whole lot more that is broken than the slow video. All I really want to do for now is speed up my full builds of Haiku by using "jam -j2" to use both cores in my CPU. I may try Xen next, but the last time I monkeyed with Xen it was far, far more broken than I am finding KVM to be. Just for now, I would be satisfied if there were some way to use my USB stick as a drive in VirtualBox. VB does allow me to configure /dev/sdb as a drive, but it always causes a fatal error when I try to launch the guest. Thank You For Any Advice You Can Give Me. -

  Read the article

• Heterogeneous Datacenter Management with Enterprise Manager 12c

  - by Joe Diemer

  The following is a Guest Blog, contributed by Bryce Kaiser, Product Manager at Blue MedoraWhen I envision a perfect datacenter, it would consist of technologies acquired from a single vendor across the entire server, middleware, application, network, and storage stack - Apps to Disk - that meets your organization’s every IT requirement with absolute best-of-breed solutions in every category.   To quote a familiar motto, your datacenter would consist of "Hardware and Software, Engineered to Work Together".  In almost all cases, practical realities dictate something far less than the IT Utopia mentioned above.   You may wish to leverage multiple vendors to keep licensing costs down, a single vendor may not have an offering in the IT category you need, or your preferred vendor may quite simply not have the solution that meets your needs.    In other words, your IT needs dictate a heterogeneous IT environment.  Heterogeneity, however, comes with additional complexity. The following are two pretty typical challenges:1) No End-to-End Visibility into the Enterprise Wide Application Deployment. Each vendor solution which is added to an infrastructure may bring its own tooling creating different consoles for different vendor applications and platforms.2) No Visibility into Performance Bottlenecks. When multiple management tools operate independently, you lose diagnostic capabilities including identifying cross-tier issues with database, hung-requests, slowness, memory leaks and hardware errors/failures causing DB/MW issues. As adoption of Oracle Enterprise Manager (EM) has increased, especially since the release of Enterprise Manager 12c, Oracle has seen an increase in the number of customers who want to leverage their investments in EM to manage non-Oracle workloads.  Enterprise Manager provides a single pane of glass view into their entire datacenter.  By creating a highly extensible framework via the Oracle EM Extensibility Development Kit (EDK), Oracle has provided the tooling for business partners such as my company Blue Medora as well as customers to easily fill gaps in the ecosystem and enhance existing solutions.  As mentioned in the previous post on the Enterprise Manager Extensibility Exchange, customers have access to an assortment of Oracle and Partner provided solutions through this Exchange, which is accessed at http://www.oracle.com/goto/emextensibility.  Currently, there are over 80 Oracle and partner provided plug-ins across the EM 11g and EM 12c versions.  Blue Medora is one of those contributing partners, for which you will find 3 of our solutions including our flagship plugin for VMware.  Let's look at Blue Medora’s VMware plug-in as an example to what I'm trying to convey.  Here is a common situation solved by true visibility into your entire stack:Symptoms•    My database is bogging down, however the database appears okay internally.  Maybe it’s starved for resources?•    My OS tooling is showing everything is “OK”.  Something doesn’t add up. Root cause•    Through the VMware plugin we can see the problem is actually on the virtualization layer Solution•    From within Enterprise Manager  -- the same tool you use for all of your database tuning -- we can overlay the data of the database target, host target, and virtual machine target for a true picture of the true root cause. Here is the console view: Perhaps your monitoring conditions are more specific to your environment.  No worries, Enterprise Manager still has you covered.  With Metric Extensions you have the “Next Generation” of User-Defined Metrics, which easily bring the power of your existing management scripts into a single console while leveraging the proven Enterprise Manager framework. Simply put, Oracle Enterprise manager boasts a growing ecosystem that provides the single pane of glass for your entire datacenter from the database and beyond.  Bryce can be contacted at [email protected]

  Read the article

• BizTalk 2009 - The Community ODBC Adapter: Schema Generation

  - by Stuart Brierley

  Having previously detailed the installation of the Community ODBC Adapter for BizTalk 2009, the next thing I will be looking at is the generation of schemas using this ODBC adapter. Within your BizTalk 2009 project, right click the project and select Add Generated Items.  In the resultant window choose Add Adapter Metadata and click Add to open the Add Adapter Wizard. Check that the BizTalk Server and Database names are correct, select the ODBC adapter and click next. You must now set the connection string. To start with choose set, then new DSN (data source name). You now need to define the Data Source you will be connecting to.  On the User DSN tab select Add add then driver you want to use. In this case I am going to use the MySQL ODBC Driver.  A User DSN will only be visible on the current machine with you as a user. * Although I initially set up a User DSN and this was fine for creating schemas with, I later realised that you actually need a system DSN as the BizTalk host service needs this to be able connect to the database on a receive or send port. You will then be asked to Set up the MySQL ODBC Data Source.  In my case this is a local database making use of named pipes, so I had to make sure that I ticked the "Force use of named pipes" check box and removed the "# The Pipe the MySQL Server will use socket=mysql" line from the mysql.ini; with this is place the connection would fail as there is no apparent way to specify the pipe name in the ODBC driver configuration. This will then update the User DSN tab with the new Data Source.  Make sure that you select it and press OK. Select it again in the Choose Data Source window and press OK.  On the ODBC transport window select next. You will now be presented with the Schema Information window, where you must supply the namespace, type and root element names for your schema. Next choose the type of statement that you will be using to create your schema - in this case I am using a stored procedure. *I later discovered that this option is fine for MySQL stored procedures without input parameters, but failed for MySQL stored procedures with input parameters.  (I will be posting on the way to handle input parameters soon) Next you will need to specify the name of the stored procedure.  In this case I have a simple stored procedure to return all the data held by my TestTable in MySQL. Select * from TestTable; The table itself has three columns: Name, Sex and Married. Selecting finish should now hopefully create your schemas based on the input and output from your stored procedure. In my case I have:   An empty schema for the request; after all I have no parameters for the stored procedure.  A response schema comprised of a Table Record with Name, Sex and Married children. Next I will be looking at the use of the ODBC adpater with: Receive ports Send ports

  Read the article

• jrunscript as a cross platform scripting environment

  - by user12798506

  ?????????????????????????????????????????????????????????sh????????????UNIX???????????????????sh???????????????????????????????????????????Windows????????????????? sh??????????????find?grep?sed?awk???Windows??????????????????????????????????????????????????????????????????????????????????????????????Windows???Cygwin????????????sh??????Windows??????????????Cygwin????????????????????????????????????????????JDK?????jrunscript?????JavaScript???????????????????????1?????????jrunscript??????????????????? Windows???UNIX??????????????????????? find?grep?sed?awk?????????sh???????????????Windows Script Host??????? Java????????????? ??????????????????????????????????????????????????????????(?????????????????????????????????????????) ?????????????JDK 6??????????????????????????PC????????????????JDK 6?PC????????????????????????????????????JDK????????????????????????????????????????jrunscript?????????????????????????? ?????jrunscript????JavaScript?????????????????????????????????????????? 1) Windows???UNIX????????????????? ?????????????????????????????????????????JavaScript???mytool.js???????????????????????jrunscript???????????UNIX????sh???????Windows????bat????????????????????? mytool.sh (UNIX?): #!/bin/sh bindir=$(cd $(dirname $0) && pwd) case "`uname`" in CYGWIN*) bindir=`cygpath -w "$bindir"` ;; esac jrunscript "${bindir}/mytool.js" $* mytool.bat (Windows?): @echo off set bindir=%~dp0 jrunscript "%bindir%mytool.js" %* UNIX??sh????????Cygwin???????????????????????????????????????????js??????????????UNIX?Windows??????????????????????????????? 2) jrunscript??cat, cp, find?grep?????? jrunscript???UNIX?????????????????????????????????? jrunscript JavaScript built-in functions ????UNIX??sh?????????????????????UNIX?????????????????????????????????????????src??????????java????????????enum???????java?????????????????????????????????????????????? find('src', '.*.java', function(f) { grep('enum', f); }); ???????UNIX?????????????????????????????????????????????????????????????????????????????????????????cp(from, to)??????????????????????????????????????????UNIX??????????? $ cp -r src/* tmp/ ?????????????????????????????????????????find()???????cp -r????????·?????????????????????? function cpr(fromdir, todir, pattern) { if (pattern == undefined) { pattern = ".*"; } var frdir = pathToFile(fromdir).getCanonicalPath(); find(fromdir, pattern, function(f) { // relative dir of file f from 'fromdir'. var relative = f.getParentFile().getCanonicalPath().substring(frdir.length() + 1); var dstdir = pathToFile(todir + "/" + relative); if (!dstdir.exists()) { // Create the destination dir for file f. mkdirs(dstdir); } // Copy file f to 'dstdir'. cp(f, dstdir + "/" + f.getName()); }); } java?????I/O?API??Windows?????????????"/"??????????????????????????????UNIX?Windows?????????????? ????????????exec(cmd)?????????jar???????????????????????????????????????????? $ jrunscript js> exec("jar xvf example.jar") META-INF/ ?????????????µ???B META-INF/MANIFEST.MF ???W?J???????µ???B com/ ?????????????µ???B com/example/ ?????????????µ???B com/example/Bar.class ???W?J???????µ???B com/example/dummy/ ?????????????µ???B com/example/dummy/dummy.txt ?????o???????µ???B com/example/dummy.properties ?????o???????µ???B com/example/Foo.class ???W?J???????µ???B ???exec()?????????????????????????????????????????????????????????????????Windows????????????I/O??????????????????????????????????BAT????????? errmsg.bat: for /L %%i in (1,1,50) do echo "Error Message count = %%i" 1&2 jrunscript??exec()???????????????18??????????????????????????????????? C:\tmp>jrunscript -e "exec('errmsg.bat')" C:\tmp>for /L %i in (1 1 100) do echo "Error Message count = %i" 1>&2 C:\tmp>echo "Error Message count = 1" 1>&2 : C:\tmp>echo "Error Message count = 18" 1>&2 ? ??? ???????????exec()?????????????????????????????????????????????????????????????????DataInputStream???????????????????????? $ jrunscript js this["exec"].toString() function exec(cmd) { var process = java.lang.Runtime.getRuntime().exec(cmd); var inp = new DataInputStream(process.getInputStream()); var line = null; while ((line = inp.readLine()) != null) { println(line); } process.waitFor(); $exit = process.exitValue(); } ?????????????????????????????????????????????????????exec()???????????????exec()?????????????????????????????exec()??????? function exec(cmd) { var process = java.lang.Runtime.getRuntime().exec(cmd); var stdworker = new java.lang.Runnable( {run: function() { cat(process.getInputStream()); }}); var errworker = new java.lang.Runnable( {run: function() { cat(process.getErrorStream()); }}); new java.lang.Thread(stdworker).start(); new java.lang.Thread(errworker).start(); return proc.waitFor(); } ???????????????????cat()???????????cat()?InputStreamReader?????????????????????????????????????????????????? 3) JavaScript???????????????? JavaScript?Java???????????????????????JavaScript????????????Ruby?Groovy?Scala???????????????????????????????????????????????10MB?????????????????????????????????????JavaScript????????????????????KB?????????????MB?JAR??????????????????????????JRE?JDK?????????????????????????????????????????

  Read the article

< Previous Page | 487 488 489 490 491 492 493 494 495 496 497 498  | Next Page >