Search Results

Search found 13807 results on 553 pages for 'undefined reference'.

Page 492/553 | < Previous Page | 488 489 490 491 492 493 494 495 496 497 498 499  | Next Page >

• How to configure Transparent IP Address Sharing (TAS) on a Mediatrix 4102 with DGW 2.0 firmware?

  - by Pascal Bourque

  I am making the switch to VoIP. I chose voip.ms as my service provider and Mediatrix 4102 as my ATA. One reason why I chose the Mediatrix over other popular consumer ATAs is that it's supposed to be easy to place it in front of the router, so it can give priority to its own upstream traffic over the home network's upstream traffic. This is supposed to work transparently, with the ATA and router sharing the same public IP address (the one obtained from the modem). They call this feaure Transparent IP Address Sharing, or TAS. Their promotional brochure describes it like this: The Mediatrix 4102 also uses its innovative TAS (Transparent IP Address Sharing) technology and an embedded PPPoE client to allow the PC (or router) connected to the second Ethernet port to have the same public IP address, eliminating the need for private IP addresses or address translations. I am interested by this feature because my router, an Apple Time Capsule, doesn't support QoS and cannot give priority to the voice packets if the ATA is behind the router. However, after hours of searching the web, reading the documentation, and good ol' trial and error, I haven't been able to configure the Mediatrix to run in this mode. Then I found a version of the manual that looks like it was for a previous version of the firmware (SIP), where there is an entire section dedicated to configuring TAS (starting at page 209). But my Mediatrix comes with the DGW 2.0 firmware, whose documentation does not mention TAS at all. So I tried to follow the TAS setup instructions from the SIP documentation and apply them to my DGW firmware, using the Variable Mapping Between SIP v5.0 and DGW v2.0 document as a reference, but no success. Some required SIP variables don't have an equivalent in DGW. So it looks like the DGW firmware does not support TAS at all, or if it does they are not doing anything to help us set it up. So right now, the Mediatrix is behind the router and VoIP works perfectly except when my upstream bandwidth is saturated. My questions are: Is downgrading to SIP firmware the only way to have my Mediatrix 4102 run in TAS mode? If not, anybody knows how to setup TAS on the DGW firmware? Is TAS mode the only way to give priority to the voice packets if I want to keep my current router (Apple Time Capsule)? Thanks!

  Read the article

• Problems with Windows XP Plug and Play devices, maybe relating to MSVCR71.dll

  - by Richard

  I believe this question is unanswered as of now so I appologize if I've overlooked it. I have been having trouble some external devices with windows recently and I'm trying my darnedest to get to the bottom of it. At first, my Zero Tension USB mouse would stop working...as in the laser in the bottom of it would be on and would register movement, but the mouse on the screen wouldn't budge even an inch. At first this would happen randomly and then it would correct itself. As time went on, it became more and more frequent. At some point, the computer would make the "doo doo" sound of plugging or unplugging a USB device when the mouse stopped/started working. I dealt with it for a while and usually if I rebooted my machine, the mouse would work again for a day or two. As more time has gone on, the computer fully does not recognize the mouse AT ALL...I have another mouse that I use with the computer that works just fine and cannot seem to figure out why my Zero Tension mouse has failed. I tried plugging the Zero Tension mouse into my Mac and low and behold, it works without hesitation and never stops on me... Needless to say, I am stumped about this. I figured because I had another mouse I could deal with the loss of my fancy one for now...until my speakers stopped being recognized. I have a set of Logitec speakers that I have plugged into my sound card. Again, every now and again the audio devices would cease to be recognized by my computer, but a reboot would fix the problem. Now my speakers do not work at all with my computer and I feel like it's time to ask for help. My computer seems to be having a neural shutdown...where I can plug in devices and the computer doesn't seem to notice anything wrong, but none of the devices work. I hope this doesn't get any worse! Please help! Also, on a potentially (un)related note, when I start up my machine I get the message "This application has failed to start because Msvcp71.dll was not found. Re-installing the application may fix this problem." in reference to qbupdate.exe I don't know if that DLL being messed up has anything to do with my mouse or speakers, but I figure it might...anyway, thanks in advance for an answer and let me know if I need to clarify anything. Let me sum up: Zero Tension Mouse gradually stopped working Logitec Speakers gradually stopped working MSVCR71.dll seems to be messed up I don't know if any of those are related but any help would be much appreciated

  Read the article

• How to start nginx via different port(other than 80)

  - by Zhao Peng

  Hi I am a newbie on nginx, I tried to set it up on my server(running Ubuntu 4), which already has apache running. So after I apt-get install it, I tried to start nginx. Then I get the message like this: Starting nginx: the configuration file /etc/nginx/nginx.conf syntax is ok configuration file /etc/nginx/nginx.conf test is successful [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) [emerg]: bind() to 0.0.0.0:80 failed (98: Address already in use) That makes sense as Apache is using port 80. Then I tried to modify nginx.conf, I reference some articles, so I changed it like so: server { listen 8080; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:8080; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } After saving this and try to start nginx again, I still get the same error as previously. I cannot really find a related post about this, could any good people shred some light? Thanks in advance :) ========================================================================= I should post all the content in conf here: user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; server { listen 81; location / { proxy_pass http://94.143.9.34:9500; proxy_set_header Host $host:81; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Via "nginx"; } } } mail { See sample authentication script at: http://wiki.nginx.org/NginxImapAuthenticateWithApachePhpScript auth_http localhost/auth.php; pop3_capabilities "TOP" "USER"; imap_capabilities "IMAP4rev1" "UIDPLUS"; server { listen localhost:110; protocol pop3; proxy on; } server { listen localhost:143; protocol imap; proxy on; } } Basically, I changed nothing except adding the server part.

  Read the article

• VBA + Polymorphism: Override worksheet functions from 3rd party

  - by phi

  my company makes extensive use of a data provider using a (closed source) VBA plugin. In principal, every query follows follows a certain structure: Fill one cell with a formula, where arguments to the formula specify the query the range of that formula is extended (not an arrray formula!) and cells below/right are filled with data For this to work, however, a user has to have a terminal program installed on the machine, as well as a com-plugin referenced in VBA/Excel. My Problem These Excelsheets are used and extended by multiple users, and not all of them have access to the data provider. While they can open the sheet, it will recalculate and the data will be gone. However, frequent recalculation is required. I would like every user to be able to use the sheets, without executing a very specific set of formulas. Attempts remove the reference on those computers where I do not have terminal access. This generates a NAME error i the cell containing the query (acceptable), but this query overrides parts of the data (not acceptable) If you allow the program to refresh, all data will be gone after a failed query Replace all formulas with the plain-text result in the respective cells (press a button and loop over every cell...). Obviously destroys any refresh-capabilities the querys offer for all subsequent users, so pretty bad, too. A theoretical idea, and I'm not sure how to implement it: Replace the functions offered by the plugin with something that will be called either first (and relay the query through to the original function, if thats available) or instead of the original function (by only deploying the solution on non-terminal machines), which just returns the original value. More specifically, if my query function is used like this: =GETALLDATA(Startdate, Enddate, Stockticker, etc) I would like to transparently swap the function behind the call. Do you see any hope, or am I lost? I appreciate your help. PS: Of course I'm talking about Bloomberg... Some additional points to clarify issues raise by Frank: The formula in the sheets may not be changed. This is mission-critical software, and its way too complex for any sane person to try and touch it. Only excel and VBA may be used (which is the reason for the previous point...) It would be sufficient to prevent execution of these few specific formulas/functions on a specific machine for all excel sheets to come This looks more and more like a problem for stackoverflow ;-)

  Read the article

• filtering itunes library items by file location

  - by Cawas

  3 answers and unfortunately no solution yet. The Problem I've got way more than 1000 duplicated items in my iTunes Library pointing to a non-existant place (the "where" under "get info" window), along with other duplicated items and other MIAs (Missing In Action). Is there any simple way to just delete all of them and only them? From the library, of course. By that I mean some MIAs are pointing to /Volumes while some are pointing to .../music/Music/... or just .../music/.... I want to delete all pointing to /Volumes as to later I'll recover the rest. Check the image below. Some Background I tried searching for a specific key word on the path and creating smart play list, but with no result. Being able to just sort all library by path would be a perfect solution! I believe old iTunes could do that. PowerTunes can do it (sort by path) but I can't do anything with its list. I would also welcome any program able to handle this, then import and properly export back the iTunes library. Since this seems to just not be clear enough... AppleScript doesn't work That's because AppleScript just can't gather the missing info anywhere in iTunes Library. Maybe we could use AppleScript by opening the XML file, but that's a whole nother issue. Here's a quote from my conversation with Doug the man himself Adams last december: I don't think you do understand. There is no way to get the path to the file of a dead track because iTunes has "forgotten" it. That is, by definition, what a dead track is. Doug On Dec 21, 2010, at 7:08 AM, Caue Rego wrote: yes I understand that and have seem the script. but I'm not looking for the file. just the old broken path reference to it. Sent from my iPhone On 21/12/2010, at 10:00, Doug Adams wrote: You cannot locate missing files of dead tracks because, by definition, a dead track is one that doesn't have any file information. If you look at "Super Remove Dead Tracks", you will notice it looks for tracks that have "missing value" for the location property.

  Read the article

• IIS httpTracing setting has no effect

  - by digahill

  I'm trying to troubleshoot some performance issues we are having on a specific ASP.NET page with Microsoft's Perfecto Tool on IIS 7.5. Perfecto uses the ETW hooks build in to IIS to report on specific HTTP request, and is working quite well. However, I only want IIS to emit traces for one specific page, say "Default.aspx" in my TestApp Web Application. Following the instructions on the httpTracing man page, I should be able to add the traceUrls element to my root web.config file for TestApp. This doesn't seem to affect tracing whatsoever when I do so. For example, I've used the following settings in the web.config file and every request that hits the IIS server is sending tracing messages that are in turn picked up by Perfecto. (In the System.WebServer section) <httpTracing> <traceUrls> <add value="/Default.aspx" /> </traceUrls> </httpTracing> I then found that the applicationHost.config file on the server had an empty element. I tried removing this element, as well as the httpTracing element in the web.config. After a machine reboot, I was still getting tracing messages! My understanding is that the presense of the httpTracing element is what controlls whether ETW tracing is on or not. I ensured there was no reference to httpTracing in the machine.config, too. At a loss, I decided to remove the IIS Tracing feature with Server Manager. After a reboot, I no longer got ETW tracing. I then reinstalled IIS Tracing feature with Server Manager. As expected, the httpTracing element reappeared in the applicationhost.config file. Tracing messages began sending again for all sites and pages. I then tried to use the traceUrls element at the applicationhost.config level. This also didn't filter out and traces. I must be misunderstanting something key with how httpTracing works. There aren't many resources on the web to help me, either. Can anyone tell me if what I'm trying should work? Has anyone else had success filtering tracing message per page with traceUrls? I should note that I also tried changing with the following setting in applicationhost.config to "allow". It didn't seem to help. <section name="httpTracing" overrideModeDefault="Allow" />

  Read the article

• Can Vagrant point to a directory of Puppet manifests for execution?

  - by SeligkeitIstInGott

  I am using Vagrant to jump start some initial Puppet config and am confused on how to include/run multiple manifests (other than just site.pp) in the puppet execution workflow without making the extra manifests into modules and including them that way. In the puppet manifests directory that I point Vagrant to (see below) I have two manifests that I want executed: site.pp and hierasetup.pp. config.vm.provision "puppet" do |puppet| puppet.manifests_path = "puppet_files/manifests" puppet.module_path = "puppet_files/modules" puppet.manifest_file = "site.pp" puppet.options = "--verbose --debug" end Currently I am having site.pp be the manifest that calls hierasetup.pp. My site.pp looks like this: File { owner => 'root', group => 'root', mode => '0644', } import "hierasetup.pp" include jboss But I get this error about the deprecation of "import": Warning: The use of 'import' is deprecated at /tmp/vagrant-puppet-1/manifests/site.pp:33. See http://links.puppetlabs.com/puppet-import-deprecation (at grammar.ra:610:in `_reduce_190') According to the referenced URL under "Things to try instead" it says "To keep your node definitions in separate files, specify a directory as your main manifest". Further this puppet doc on main manifests says: "Recommended: If you’re using the main manifest heavily instead of relying on an ENC, consider changing the manifest setting to $confdir/manifests. This lets you split up your top-level code into multiple files while avoiding the import keyword. It will also match the behavior of simple environments." It appears that Puppet can reference an entire directory instead of just a specific manifest file, such that I would expect that Vagrant would make a provision for this and allow me to drop the "puppet.manifest_file = "site.pp" line and point to the parent directory instead in which all the *.pp files there will be executed. However removing that line in Vagrant merely generates a complaint about an expected "default.pp" in its stead: puppet provisioner: * The configured Puppet manifest is missing. Please specify a path to an existing manifest: /some/path/puppet_files/manifests/default.pp So: Firstly, do I understand the "new" (non-import) way of calling multiple manifests correctly, in that a directory is to be pointed to in which all the *.pp files inside it will be executed? And secondly, has Vagrant "caught up" with this new change to accommodate the referencing of directories in conjunction with Puppet's deprecation of "import"? Update: Thanks to Shane the issue with #2 (Vagrant's code not being caught up to allow pointing to puppet manifest directories) was reported on Vagrant's GitHub issue tracker site and has since been patched: https://github.com/mitchellh/vagrant/issues/4169

  Read the article

• Unable to locate Windows Server Error log files

  - by Sam007

  I am getting an error in my application on 500 Internal Server Error. The firebug gives me, NetworkError: 500 Internal Server Error - http://webgis.arizona.edu/ArcGIS/rest/services/webGIS/Shock_Models/GPServer/Income_Log/jobs/jc09c501156564f71abc5d98393581267/results/final_shp?dpi=96&transparent=true&format=png8&imageSR=102100&f=image&bbox=%7B%22xmin%22%3A-14519891.438356264%2C%22ymin%22%3A637618.0139790997%2C%22xmax%22%3A-6692739.741956295%2C%22ymax%22%3A6507981.786279075%2C%22spatialReference%22%3A%7B%22wkid%22%3A102100%7D%7D&bboxSR=102100&size=800%2C600 And when I goto that particular link, I get this error, Server Error - Object reference not set to an instance of an object. Any idea how I can correct it? UPDATE I was told to use fiddler and see the error details that is occurring over the network and this is the output that I got, SESSION STATE: Done. Response Entity Size: 849 bytes. == FLAGS ================== BitFlags: [ClientPipeReused, ServerPipeReused] 0x18 X-CLIENTPORT: 2010 X-RESPONSEBODYTRANSFERLENGTH: 849 X-EGRESSPORT: 2023 X-HOSTIP: 128.196.53.161 X-PROCESSINFO: firefox:2248 X-CLIENTIP: 127.0.0.1 X-SERVERSOCKET: REUSE ServerPipe#2 == TIMING INFO ============ ClientConnected: 15:53:51.383 ClientBeginRequest: 15:53:51.494 GotRequestHeaders: 15:53:51.494 ClientDoneRequest: 15:53:51.494 Determine Gateway: 0ms DNS Lookup: 0ms TCP/IP Connect: 0ms HTTPS Handshake: 0ms ServerConnected: 15:52:45.077 FiddlerBeginRequest: 15:53:51.495 ServerGotRequest: 15:53:51.495 ServerBeginResponse: 15:53:51.679 GotResponseHeaders: 15:53:51.679 ServerDoneResponse: 15:53:51.679 ClientBeginResponse: 15:53:51.679 ClientDoneResponse: 15:53:51.679 Overall Elapsed: 00:00:00.1850106 The response was buffered before delivery to the client. == WININET CACHE INFO ============ This URL is not present in the WinINET cache. [Code: 2] * Note: Data above shows WinINET's current cache state, not the state at the time of the request. * Note: Data above shows WinINET's Medium Integrity (non-Protected Mode) cache only. But I am still confused as to what the error is? This is the application. I am not sure if the error is due to the ArcGIS-Server or the Windows Server 2008. I am new on working with the Windows Server and wanted to know where can I look for the error lof files? This is the link which gives the details and the log info of the job executed. This is the output.

  Read the article

• Exchange 2010 Internal Auto Discover Migrate away from current .local DNS name

  - by Bryan

  We have an Exchange 2010 Server, running within our Active Directory domain, with an internal hostname of server.example.local. The server is configured for Exchange anywhere, but currently has a self signed certificate with a name of server.example.local installed. Internally, clients connect and work fine, but externally, we are having certificate errors as you would expect. I'm about to purchase a UCC SSL Certificate to install on the server with all the relevant SANs on the certificate to correct this, but due to obvious problem obtaining a trusted cert with .local as a subject alternative name, I'm looking to configure clients on the internal network so that they don't use any reference to the .local hostname. I've configured our external DNS name for the server as exchange.example.com, and have created an CNAME for autodiscover.example.com which also (correctly) points to exchange.example.com. I've also configured internal DNS records for these two hostnames which point to the internal interface of the same server. I don't anticipate any problems here. I'm now trying to reconfigure Auto Discover internally, so that Outlook attempts to connect to exchange.example.com. I've followed the steps in KB940726 to prepare for this, and this appeared to work fine. No errors were generated and I was able to verify the CAS name in AD using ADSI edit. I've just tried testing this with a newly created test user account complete with a new Exchange mailbox, and Outlook 2007 connects fine on the internal network, but looking deeper in the Exchange profile, Outlook is still resolving the server name as server.example.local. Could it be the self signed cert, that is causing Outlook to display the server name as server.example.local, or is there still something wrong with my internal autodiscover configuration? Edit I've proven it isn't the certificate that is responsible for outlook returning server.example.local, by installing another self certified certificate with a name of test.example.com. When creating a new outlook profile, I get the mismatch error I'm expceting, but after accepting the cert, and finishing the config of the Outlook profile, again it still shows server.example.local as the server name. This means that if I were to purchase the UCC cert now, that external client would work fine, but internal clients would show a certificate name mismatch. Any ideas where to start diagnosing this?

  Read the article

• How to Configure Source NAT (Private IP => Public IP Outbound)

  - by DavidScherer

  I'm running VMWare ESXi Free and have Zentyal SBS 3.2 running as a Gateway. I have 5 Public IPS (CIDR/29, let's call them 69.1.1.1 - 69.1.1.5) and currently Zentyal is bound to 69.1.1.1 as the Gateway, with the other 4 Public IPs set as Virtual Interfaces in Zentyal (wan2-wan5) I have machines sitting on the Private Network (10.34.251.x) that, when going Outbound (to Google for instance) should be seen by the Internet as an IP other than the Gateway (69.1.1.1), this is because our machines need to be able to communicate with 3rd party APIs that expect these requests to come from a specific IP. From what I could find, SNAT (Source NAT) in Zentyal is used to achieve this, but I'm not sure how to configure it and cannot find a specific piece of Documentation for it at Zentyal. I've tried setting this up a couple different ways, with no results and at this point I have no idea if I'm going about this completely wrong, or my lack of experience with networking and the associated terminology is preventing me from placing the correct values in the correct fields. I get the following form to set up "SNAT" rules in Zentyal: Perhaps someone can offer some guidance and definitions for the fields above? SNAT Address Is this the Public IP I want to masquerade? Outgoing Interface Should this by my External NIC (one connected to Public 'Net), or is it the "Private" interface? It sounds as though this should be the External interface as I want the traffic from the internal network sent Out over this Interface (using a different IP than normal, anyway) Source Is the the Source on the internal network (one of the private IPs?), a public IP I want to masquerade as, or something else entirely? Destination Is this a place on the Internet (eg, "Only do this for the Site Google.com"/IP) or am I allowing myself to become confused again? Service I'm assuming this allows me to restrict which services this rule will apply to, but is it for a service on the internal network or a service being accessed on the external network? If I can offer any further details or information to make what I'm trying to do more clear, I will happily do so. Honestly any kind of help here would be very appreciated. I'm not a NetOps or anything even close, I spend most of my day writing code and my entire "team" at this company consists of "me, myself, and I" so while I try to broaden my KB at every possible opportunity, I can only learn so much, so fast and I feel like with networking especially there's just so much, coupled with a learning curve for each solution that likes to (from my limited perspective) use slightly different terminology that what I'm used to (and I don't exactly have the necessary experience to cross reference this stuff with the stuff I already know in context).

  Read the article

• Both nginx and php5-fpm init.d startup scripts are non-functional and returning no errors..? But they used to work perfectly

  - by Ollie Treend

  I have been using nginx and php5-fpm on my Ubuntu box for a while now. Everything has been configured and setup correctly, and it ran like a charm. I have been keeping the packages updated & upgraded as usual, but haven't touched the nginx OR php5-fpm config files at all (thus I'm pretty sure this isn't my fault... ) Basically, I noticed nginx wasn't running as it should be. I ran the command sudo service nginx start, and the script did nothing. The same thing happens when trying to do anything - start, stop, restart or reload. This also happens for the "php5-fpm" init script - although all other init scripts seem to be functioning correctly. When trying to start nginx OR php5-fpm, this is what happens: root@HAL:/etc# service php5-fpm start root@HAL:/etc# I can't understand what is going wrong. The script isn't returning errors, but similarly it isn't starting the daemon or reporting success as usual. For reference, both installations are from the official nginx and php5-fpm PPAs. The fact that both started doing this at the same time has thrown me - since they are both unrelated packages. I have since purged both sets of packages from my system with apt-get purge ... and also apt-get remove --purge ... both of which have successfully removed the packages, their config files, and their init.d startup scripts. After having reinstalled nginx, I now have a functioning startup script again - I can start the web server as usual. However, php5-fpm is still experiencing the strange premature exiting of the startup script.. and I really can't figure out what's causing it. I have no idea what caused this to occur initially, but have managed to fix nginx. I now need to fix the php5-fpm startup script. If anybody could shed some light on this situation, I would be very grateful! The chances are both these issues are related - and they were caused by me doing something stupid. But now I need to fix it. This time I was lucky - because these problems are just on my development server. But I have 2 other live servers which are configured in a similar way, and I am worried the same thing will happen to these two as well! Has anybody else come across this? Do you have any words of advice? Thank you

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• How can the Private Bytes of a process be significantly less than its effect on the system commit charge?

  - by bacar

  On a 64-bit Windows Server 2003, I can see using taskmgr or process explorer that the total commit charge is around 3.5GB, yet when I sum the Private Bytes consumed by each process (by running pslist -m and adding all values under the Priv column) the total comes in at 1.6GB. I know which process seems to be causing this (sqlservr.exe) as when I kill the process, the commit charge drops dramatically. However the process in question is consuming only ~220MB of Private Bytes yet killing the process drops the commit charge by ~1.6GB. How is this possible? How can the commit charge be so significantly greater than Private Bytes, which should represent the amount of committed memory? If some other factor contributes to the commit charge, what is that factor and how can I view its impact in process explorer? Note: I claim that I understand the difference between reserved and committed memory already: my investigations above relate specifically to Private Bytes which includes only committed memory and excludes reserved memory. the Virtual Size of the process in this case is over 4GB, but this should be irrelevant - Virtual Size in procexp represents reserved, not committed memory, and should not contribute to the commit charge. I'm particularly interested in generalised answers to this question: I'm assuming that if sqlservr.exe can behave in this way, that any process potentially could. Further Investigations I notice that pointing Sysinternals VMMap at this process reports a committed "Private Data" of 1.6GB despite Procexp's reported a Private Bytes of 220MB. This is particularly strange given that the documentation for this field in the "Windows® Sysinternals Administrator's Reference" states that: Private Data memory is memory that is allocated by VirtualAlloc and that is not further handled by the Heap Manager or the .NET runtime, or assigned to the Stack category... VMMap’s definition of “Private Data” is more granular than that of Process Explorer’s “private bytes.” Procexp’s “private bytes” includes all private committed memory belonging to the process. i.e. that VMMap's committed "Private Data" should be smaller than procexp's "Private Bytes". Also, after reading the 'Process committed memory' section of Mark Russinovich's excellent Pushing the Limits of Windows: Virtual Memory, he highlights two cases which won't show up in Private Bytes: File mapping views with copy-on-write semantics (however, according to VMMap there is no significant space allocated to Mapped Files). pagefile-backed virtual memory (however, I tried testlimit with the -l flag as suggested, and no significant memory is consumed by pagefile-backed sections)

  Read the article

• How to tune system settings for mongoDB on Linux?

  - by jsh

  Trying to squeeze a lot out of one question here -- please bear with me. Although the MongoDB man pages make several useful recommendations about system settings like ulimit (http://docs.mongodb.org/manual/reference/ulimit/), and other production factors (http://docs.mongodb.org/manual/administration/production-notes/) they seem mysteriously silent on things like virtual memory and swap settings. The closest we get to a hint is that "...the operating system’s virtual memory subsystem manages MongoDB’s memory..." (http://docs.mongodb.org/manual/faq/fundamentals/#does-mongodb-require-a-lot-of-ram). Running the same job - high writes and high reads on about 10,000,000 records in a single collection -- on my 4-processor, 4GB RAM macbook and an 8-core ubuntu box with 64GB RAM I saw dramatically WORSE read performance on the linux box with factory settings, and could hear the disk constantly spinning, indicating high I/O and presumably swapping. Yes, other things were happening on the box, but there was plenty of free RAM, disk space, etc.; furthermore, I did not see evidence that Mongo was expanding to take advantage of all that free RAM as it is touted to do. Linux box default settings were as follows: vm.swappiness =60 vm.dirty_background_ratio = 10 vm.dirty_ratio = 20 vm.dirty_expire_centisecs =3000 vm.dirty_writeback_centisecs=500 I hazarded some guesses looking at docs and blogs for other types of databases (Oracle, MYSQL, etc.), experimented, and adjusted as below. vm.swappiness=10 vm.dirty_background_ratio=5 vm.dirty_ratio=5 vm.dirty_writeback_centisecs=250 vm.dirty_expire_centisecs=500 I saw some immediate apparent improvements in read time. However, when I ran my test jobs again, read performance continued to be painfully sluggish during heavy writes. Then, I REBUILT the collection from an available data source - and suddenly I can read at 1ms or less per record WHILE doing the write job! So the question is really two-fold: 1) What are appropriate VM settings for MongoDB on Linux? 2) (bonus) Does Mongo do some checking or optimization with the OS while data is being built? In other words, if I have built a large data set with suboptimal VM or I/O settings, does Mongo make assumptions during the memory-mapping process that will fail to take advantage of optimizations down the road? Obviously I don't fully grok memory mapping under the hood (I was hoping I wouldn't have to). Any help appreciated...thanks! -j

  Read the article

• Triple monitor setup in linux

  - by Brendan Abel

  I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

  Read the article

• How do I configure Reverse Group Membership Maintenance on an openldap server? (memberOf)

  - by emills

  I am currently working on integrating LDAP authentication into a system and I would like to restrict access based on LDAP group. The only way to do this is via a search filter and therefore I believe my only option to be the use of the "memberOf" attribute in my search filter. It is my understanding that the "memberOf" attribute is an operational attribute which can be created by the server for me anytime a new "member" attribute is created for any "groupOfNames" entry on the server. My main goal is to be able to add a "member" attribute to an existing "groupOfNames" entry and have a matching "memberOf" attribute be added to the DN I provide. What I have managed to achieve so far: I'm still pretty new to LDAP administration but based on what I found in the openldap admin's guide, it looks like Reverse Group Membership Maintence aka "memberof overlay" would achieve exactly the effect I am looking for. My server is currently running a package installation (slapd on ubuntu) of openldap 2.4.15 which uses "cn=config" style runtime configuration. Most of the examples I have found still reference the older "slapd.conf" method of static configuration and I have tried my best to adapt the configurations to the new directory based model. I have added the following entries to enable the memberof overlay module: Enable the module with olcModuleLoad cn=config/cn\=module\{0\}.ldif dn: cn=module{0} objectClass: olcModuleList cn: module{0} olcModulePath: /usr/lib/ldap olcModuleLoad: {0}back_hdb olcModuleLoad: {1}memberof.la structuralObjectClass: olcModuleList entryUUID: a410ce98-3fdf-102e-82cf-59ccb6b4d60d creatorsName: cn=config createTimestamp: 20090927183056Z entryCSN: 20091009174548.503911Z#000000#000#000000 modifiersName: cn=admin,cn=config modifyTimestamp: 20091009174548Z Enabled the overlay for the database and allowed it to use it's default settings (groupOfNames,member,memberOf,etc) cn=config/olcDatabase={1}hdb/olcOverlay\=\{0\}memberof dn: olcOverlay={0}memberof objectClass: olcMemberOf objectClass: olcOverlayConfig objectClass: olcConfig objectClass: top olcOverlay: {0}memberof structuralObjectClass: olcMemberOf entryUUID: 6d599084-490c-102e-80f6-f1a5d50be388 creatorsName: cn=admin,cn=config createTimestamp: 20091009104412Z olcMemberOfRefInt: TRUE entryCSN: 20091009173500.139380Z#000000#000#000000 modifiersName: cn=admin,cn=config modifyTimestamp: 20091009173500Z My current result: By using the above configuration, I am able to add a NEW "groupOfNames" with any number of "member" entries and have all the involved DNs updated with a "memberOf" attribute. This is part of the behavior I would expect. While I believe the following should have been accomplished with the memberof overlay, I still do not know how to do the following and I would gladly welcome any advice: Add a "member" attribute to an EXISTING "groupOfNames" and have a corresponding "memberOf" attribute be created automatically. Remove a "member" attribute and have the corresponding "memberOf" attribute" be removed automatically.

  Read the article

• bluetooth connection using pybluez

  - by srj0408

  I am working on bluetooth not exactly on bluetooth stack-development but to use bluetooth in one of my project. I had done all that before using some of the py-bluez commands like hciconfig, hcitool scan , then simple-agents and using serial module inside python. But that was quite random. We were able to connect only one specific device based on its bluetooth address and there was no facility of reconnection once the devices are disconnected. Now i want to try out this stuff in a sequential manner like this (i am doing that all on a RPI and for at present on ubuntu 12.04.) i) Store some names in a file along with some other information with respect to that device. ii) Run a script to find out the device in locality with those names and if any one if found, report that. For this step, i had taken a reference from BTBook , made available from MIT. Below is the script for the same, but that script only search for the single name. from bluetooth import * target_name = "XT1033" target_address = None nearby_devices = discover_devices() for address in nearby_devices: if target_name == lookup_name( address ): target_address = address break if target_address is not None: print "found target bluetooth device with address ", target_address connect_socket(target_address); else: print "could not find target bluetooth device nearby" iii) Connect the device using client sock. But i dont have any device on which i can write a simple python script. My client can be any device that will be publishing data. Now i came through a script in the same book, that actually connect to a client requesting permission to connect to server. from bluetooth import * port = 1 server_sock=BluetoothSocket( RFCOMM ) server_sock.bind(("",port)) server_sock.listen(1) client_sock, client_info = server_sock.accept() print "Accepted connection from ", client_info data = client_sock.recv(1024) print "received [%s]" % data client_sock.close() server_sock.close() here client_sock, client_info = server_sock.accept() provide the client address and port requested to be connected. Can i pass address obtained from the earlier script to this, so that it connect server to the client? iv) Then if client get disconnected, re-connect(a simple polling can be used.) All this stuff can be done using bash and py-bluez functions but i want to do that in a sequential manner.I am not a master in python but i can do some small stuff. Can any one guide me for the same or can direct me to more usefull resource through which i can continue my coding part after finding the "X", "Y" named devices.

  Read the article

• FTP script needs blank line

  - by Ones and Zeroes

  I am trying to determine the reason for some FTP servers requiring a blank line in the script as follows: open server.com username ftp_commands bye Refer to blank line required after username credentials. Example from: FTP from batch file another reference to the same: http://newsgroups.derkeiler.com/Archive/Comp/comp.sys.ibm.as400.misc/2008-05/msg00227.html Also discussed here: archive.midrange.com/midrange-l/200601/msg00048.html "The behavior I'm observing is the same as if I didn't specify the password to login." with an answer referring to our same fix... archive.midrange.com/midrange-l/200601/msg00053.html and archive.midrange.com/midrange-l/200601/msg00065.html Note: It is my experience that FTP questions attract uncouth responses. Admittedly FTP is outdated, but many clients still have legacy systems, which they cannot upgrade or replace. The reason thereof should not be discussed here. The intention of this question is to invite a positive response. Please do not respond if you disagree with the above. If you have never encountered this same issue, please do not respond. I suspect this may be limited to FTP scripts executed from Windows machines, but have been told that this happens often and with many different servers. My specific interest is to understand what may cause this as I have a real world example of a production system suddenly requiring this as a workaround fix, after running for many years without issue. The server belongs to a third party who claims no change on their end. Server details unknown and cannot be determined. Any help or encouragement from someone who has come across the same, would be appreciated. ps. Sorry for the many words and references to painful responses, but I have asked similar questions on serverfault and elsewhere and unfortunately got back kneejerk responses to FTP and respondents debating the validity of the question. I would truly not ask, or re-post this question online if I had a better understanding of the issue. I know of people who have seen this issue, but don't know what causes it. I am wary that this question would again turn into another irrelevant discussion. Please, I ask very nicely: Please do not respond if you have not encountered a similar issue. FURTHER EDIT: Please do not suggest changing the product. The problem is not the blank line requirement. We know this fixes the issue. The problem is not being able to explain the reason for the blank line in the first place. Slight difference, but a critical point to note wrt the answering of this question.

  Read the article

• SSRS ReportViewer 2010 Iframe IE Problem

  - by Phil

  Hello all, My problem relates to trying to include an SSRS (SQL Server) Report inside my MVC application. I've settled on the hybrid solution of having a WebForm with the ReportViewer Control in and then on my MVC View pages having an iframe reference this WebForm page. The tricky part is that the iframe needs to be dynamically populated with the report rather than using src due to posting parameters to the WebForm. It works perfectly in Firefox and Chrome, however IE throws a "Sys is Undefined" javascript error. Using src on the iframe works in IE, but I can't find a way to post parameters (don't want to use something like /Report.aspx?param1=test due to the possible length). Its a ASP.NET MVC 2 project, .NET 4, Visual Studio 2010 on Windows 7 x74 if its any help. So here is the code (I could provide the VS2010 project files if anyone wants them) In my webform: <%@ Page Language="C#" AutoEventWireup="true" CodeBehind="Report.aspx.cs" Inherits="SSRSMVC.Views.Home.Report" %> <%@ Register Assembly="Microsoft.ReportViewer.WebForms, Version=10.0.0.0, Culture=neutral, PublicKeyToken=b03f5f7f11d50a3a" Namespace="Microsoft.Reporting.WebForms" TagPrefix="rsweb" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <body> <form id="RSForm" runat="server"> <asp:ScriptManager ID="ScriptManager" runat="server" EnablePartialRendering="true" ScriptMode="Release"> </asp:ScriptManager> <asp:UpdatePanel ID="ReportViewerUP" runat="server"> <ContentTemplate> <rsweb:ReportViewer ID="ReportViewer" runat="server" Width="100%" Height="380px" ProcessingMode="Local" InteractivityPostBackMode="AlwaysAsynchronous" AsyncRendering="true"> <LocalReport ReportPath="Models\\TestReport.rdlc"> </LocalReport> </rsweb:ReportViewer> </ContentTemplate> </asp:UpdatePanel> </form> </body> </html> And Codebehind: using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; using Microsoft.Reporting.WebForms; namespace SSRSMVC.Views.Home { public partial class Report : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { if (!Page.IsPostBack) { string test = Request.Params["val1"]; ReportViewer.LocalReport.DataSources.Add(new ReportDataSource("DataSet1", new SSRSMVC.Models.DataProvider().GetData())); } } } } And lastly my View page, <script type="text/javascript"> $(window).load(function () { $.post('/Report.aspx', { val1: "Hello World" }, function (data) { var rv_frame = document.getElementById('Frame1'); rv_frame = (rv_frame.contentWindow) ? rv_frame.contentWindow : (rv_frame.contentDocument.document) ? rv_frame.contentDocument.document : rv_frame.contentDocument; rv_frame.document.open(); rv_frame.document.write(data); rv_frame.document.close(); }); }); </script>

  Read the article

• Ruby Debug IDE error : ruby-debug-ide-0.4.9/lib/ruby-debug-ide.rb:109:in `debug_load'

  - by Paul

  I hope someone can assist me. I have RubyMine 2.0.2 installed on Windows 7 32 bit computer. Since a week ago (I presume it must have been after I have update some gems) I cant seem to debug form the IDE. I am trying to debug a rake task which I could before. Running the rake task normally works perfect, just debug doesnt. Its not just limited to the rake, I cant debug any ruby files. I've tried installing older versions of debug-ide and debug-base but to no success. I've tried it with ruby 1.8.7 and 1.8.6 on different computers but nothing. Trying to search the web gave some information, which I've tried, but also no success. Im desperate to get this working. Below are the full error and my current settings: Error: C:\InstantRails\ruby\bin\ruby.exe -e STDOUT.sync=true;STDERR.sync=true;load($0=ARGV.shift) C:\InstantRails\ruby\bin/rdebug-ide --port 57167 -- C:/InstantRails/rails_apps/paperserve/lib/tasks/poll_snmp.rake Fast Debugger (ruby-debug-ide 0.4.9) listens on :57167 C:/InstantRails/rails_apps/paperserve/lib/tasks/poll_snmp.rake:5 C:/InstantRails/ruby/lib/ruby/gems/1.8/gems/ruby-debug-ide-0.4.9/lib/ruby-debug ide.rb:109:in `debug_load' C:/InstantRails/ruby/lib/ruby/gems/1.8/gems/ruby-debug-ide-0.4.9/lib/ruby-debug ide.rb:109:in `debug_program' C:/InstantRails/ruby/lib/ruby/gems/1.8/gems/ruby-debug-ide-0.4.9/bin/rdebug-ide:87 C:\InstantRails\ruby\bin/rdebug-ide:19:in `load' C:\InstantRails\ruby\bin/rdebug-ide:19 -e:1:in `load' -e:1 Uncaught exception: undefined method `namespace' for main:Object Process finished with exit code 1 Code snippet (It fails at the start of namespace. If I remove this, it fails on the next line, etc, etc) #This script should run every 15 minutes require 'snmp' require 'yaml' namespace :cdeweb do RubyGems Environment: RUBYGEMS VERSION: 1.3.7 RUBY VERSION: 1.8.6 (2007-09-24 patchlevel 111) [i386-mswin32] INSTALLATION DIRECTORY: C:/InstantRails/ruby/lib/ruby/gems/1.8 RUBY EXECUTABLE: C:/InstantRails/ruby/bin/ruby.exe EXECUTABLE DIRECTORY: C:/InstantRails/ruby/bin RUBYGEMS PLATFORMS: ruby x86-mswin32-60 GEM PATHS: C:/InstantRails/ruby/lib/ruby/gems/1.8 C:/Users/Paul.LPFSYSTEMS/.gem/ruby/1.8 GEM CONFIGURATION: :update_sources = true :verbose = true :benchmark = false :backtrace = false :bulk_threshold = 1000 REMOTE SOURCES: http://rubygems.org/ * LOCAL GEMS * actionmailer (2.3.5, 2.0.2) actionpack (2.3.5, 2.0.2) activerecord (2.3.5, 2.0.2) activeresource (2.3.5, 2.0.2) activesupport (2.3.5, 2.0.2) capistrano (2.5.18, 2.1.0) cgi_multipart_eof_fix (2.5.0) cmdparse (2.0.2) columnize (0.3.1) fxri (0.3.7, 0.3.6) fxruby (1.6.12 mswin32) gem_plugin (0.2.3) highline(1.5.2, 1.4.0) hpricot (0.8.2 x86-mswin32, 0.6 mswin32) inaction_mailer (0.6) json (1.4.2 x86-mswin32) json_pure (1.4.2) linecache (0.43 mswin32) log4r (1.1.7, 1.0.5) mongrel (1.1.5 x86-mswin32-60, 1.1.2 mswin32) mysql(2.8.1 x86-mswin32, 2.7.3 mswin32) needle (1.3.0) net-scp (1.0.2) net-sftp (2.0.4, 1.1.0) net-ssh (2.0.22, 1.1.2) net-ssh-gateway (1.0.1) rack (1.0.1) rails (2.3.5, 2.0.2) rake (0.8.7, 0.8.1, 0.8.0, 0.7.3) ruby-debug-base (0.10.3 mswin32) ruby-debug-ide (0.4.9) ruby-net-ldap (0.0.4) rubygems-update (1.3.7, 1.3.6, 1.0.1) snmp (1.0.2) sources (0.0.1) sqlite3-ruby (1.2.5 x86-mswin32, 1.2.1 mswin32) win32-api (1.4.6 x86-mswin32-60, 1.0.4 mswin32) win32-clipboard (0.5.2, 0.4.3) win32-dir (0.3.6, 0.3.2) win32-eventlog (0.5.2, 0.4.6) win32-file (0.6.3, 0.5.4) win32-file-stat (1.3.4, 1.2.7) win32-process (0.6.2, 0.5.3) win32-sapi (0.1.5, 0.1.4) win32-sound (0.4.2, 0.4.1) windows-api (0.4.0, 0.2.0)

  Read the article

• Rails Rake Error with XAMPP mysql database

  - by edu222

  I have installed XAAMP on my win7 machine and I have the apache server/mysql running on there. I set up rails to work with XAmpp as described here: XAMPP and RAILS This tutorial advises you to add this code to the XAMPP httpd.connf : Listen 3000 LoadModule rewrite_module modules/mod_rewrite.so ################################# # RUBY SETUP ################################# <virtualHost *:3000> ServerName rails DocumentRoot "c:/xampp/htdocs/FirstProject/public" <Directory "c:/xampp/htdocs/FirstProject/public/"> Options ExecCGI FollowSymLinks AllowOverride all Allow from all Order allow,deny AddHandler cgi-script .cgi AddHandler fastcgi-script .fcgi </Directory> </VirtualHost> ################################# # RUBY SETUP ################################# Xampp runs on the default localhost and mysql remains unchanged without a pw. I created a rails app with a mysql database like this: rails -d mysql C:/xampp/htdocs/FirstProject Then I started the ruby script/server from within the FirstProject location The localhost:3000/ shows the classic rails welcome I then ran a basic scaffold command: ruby script/generate scaffold FirstProject name:string email:string <br/> When I run the rake db:migrate command I get the following error: C:\xampp\htdocs\FirstProject>rake db:migrate --trace (in C:/xampp/htdocs/FirstProject) ** Invoke db:migrate (first_time) ** Invoke environment (first_time) ** Execute environment ** Execute db:migrate rake aborted! undefined method `init' for Mysql:Class C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/mysql_adapter.rb:70:in `mysql_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:223:in `send' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:223:in `new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:245:in `checkout_new_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:188:in `checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:184:in `loop' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:184:in `checkout' C:/Ruby/lib/ruby/1.8/monitor.rb:242:in `synchronize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:183:in `checkout' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:98:in `connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_pool.rb:326:in `retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_specification.rb:123:in `retrieve_connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/connection_a dapters/abstract/connection_specification.rb:115:in `connection' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :435:in `initialize' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :400:in `new' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :400:in `up' C:/Ruby/lib/ruby/gems/1.8/gems/activerecord-2.3.5/lib/active_record/migration.rb :383:in `migrate' C:/Ruby/lib/ruby/gems/1.8/gems/rails-2.3.5/lib/tasks/databases.rake:116 C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `call' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:636:in `execute' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `each' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:631:in `execute' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:597:in `invoke_with_call_c hain' C:/Ruby/lib/ruby/1.8/monitor.rb:242:in `synchronize' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:590:in `invoke_with_call_c hain' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:583:in `invoke' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2051:in `invoke_task' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `each' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2029:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exceptio n_handling' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2023:in `top_level' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2001:in `run' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:2068:in `standard_exceptio n_handling' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/lib/rake.rb:1998:in `run' C:/Ruby/lib/ruby/gems/1.8/gems/rake-0.8.7/bin/rake:31 C:/Ruby/bin/rake:19:in `load' C:/Ruby/bin/rake:19 Any idea on how to fix this? Thanks in advance

  Read the article

• Debugging matchit plugin in vim (under Cygwin)

  - by system PAUSE

  The "matchit" plugin for vim is supposed to allow you to use the % key to jump between matching start/end tags when editing HTML, as well as /* and */ comment delimiters when editing other kinds of code. I've followed the exact instructions in ":help matchit", but % still doesn't work for me. It seems silly to ask "Why doesn't this work?" so instead I'm asking How can I diagnose the problem? Pointers to references are welcome, but specific vim-plugin-debugging techniques are preferred. Here is the ~/.vim directory: $ ls -ltaGR ~/.vim /cygdrive/y/.vim: total 0 drwxr-xr-x 1 spause 0 Sep 17 13:20 .. drwxr-xr-x 1 spause 0 Sep 16 13:59 doc drwxr-xr-x 1 spause 0 Sep 16 13:58 . drwxr-xr-x 1 spause 0 Sep 16 13:58 plugin /cygdrive/y/.vim/doc: total 24 -rw-r--r-- 1 spause 1961 Sep 16 13:59 tags drwxr-xr-x 1 spause 0 Sep 16 13:59 . -rw-r--r-- 1 spause 19303 Sep 16 13:58 matchit.txt drwxr-xr-x 1 spause 0 Sep 16 13:58 .. /cygdrive/y/.vim/plugin: total 32 drwxr-xr-x 1 spause 0 Sep 16 13:58 .. -rw-r--r-- 1 spause 30714 Sep 16 13:58 matchit.vim drwxr-xr-x 1 spause 0 Sep 16 13:58 . I am running vim 7.2 under Cygwin (installed Fall 2008). cygcheck shows: 1829k 2008/06/12 C:\cygwin\bin\cygwin1.dll Cygwin DLL version info: DLL version: 1.5.25 DLL epoch: 19 DLL bad signal mask: 19005 DLL old termios: 5 DLL malloc env: 28 API major: 0 API minor: 156 Shared data: 4 DLL identifier: cygwin1 Mount registry: 2 Cygnus registry name: Cygnus Solutions Cygwin registry name: Cygwin Program options name: Program Options Cygwin mount registry name: mounts v2 Cygdrive flags: cygdrive flags Cygdrive prefix: cygdrive prefix Cygdrive default prefix: Build date: Thu Jun 12 19:34:46 CEST 2008 CVS tag: cr-0x5f1 Shared id: cygwin1S4 In vim, :set shows: --- Options --- autoindent fileformat=dos shiftwidth=3 background=dark filetype=html syntax=html cedit=^F scroll=24 tabstop=3 expandtab shelltemp textmode viminfo='20,<50,s10,h Notably, the syntax and filetype are both recognized as HTML. (The syntax colouring is just fine.) If additional info is needed, please comment. UPDATE: Per answer by too much php: After trying vim -V1, I had changed my .vimrc to include a line set nocp so the compatible option is not on. :let loadad_matchit loaded_matchit #1 :set runtimepath? runtimepath=~/.vim,/usr/share/vim/vimfiles,/usr/share/vim/vim72,/usr/share/vim/vimfiles/after,~/.vim/after (~ is /cygdrive/y) Per answer by michael: :scriptnames 1: /cygdrive/y/.vimrc 2: /usr/share/vim/vim72/syntax/syntax.vim 3: /usr/share/vim/vim72/syntax/synload.vim 4: /usr/share/vim/vim72/syntax/syncolor.vim 5: /usr/share/vim/vim72/filetype.vim 6: /usr/share/vim/vim72/colors/evening.vim 7: /cygdrive/y/.vim/plugin/matchit.vim 8: /cygdrive/y/.vim/plugin/python_match.vim 9: /usr/share/vim/vim72/plugin/getscriptPlugin.vim 10: /usr/share/vim/vim72/plugin/gzip.vim 11: /usr/share/vim/vim72/plugin/matchparen.vim 12: /usr/share/vim/vim72/plugin/netrwPlugin.vim 13: /usr/share/vim/vim72/plugin/rrhelper.vim 14: /usr/share/vim/vim72/plugin/spellfile.vim 15: /usr/share/vim/vim72/plugin/tarPlugin.vim 16: /usr/share/vim/vim72/plugin/tohtml.vim 17: /usr/share/vim/vim72/plugin/vimballPlugin.vim 18: /usr/share/vim/vim72/plugin/zipPlugin.vim 19: /usr/share/vim/vim72/syntax/html.vim 20: /usr/share/vim/vim72/syntax/javascript.vim 21: /usr/share/vim/vim72/syntax/vb.vim 22: /usr/share/vim/vim72/syntax/css.vim Note that matchit.vim, html.vim, tohtml.vim, css.vim, and javascript.vim are all present. :echo b:match_words E121: Undefined variable: b:match_words E15: Invalid expression: b:match_words Hm, this looks highly relevant. I'm now looking through :help matchit-debug to find out how to fix b:match_words.

  Read the article

• Perl CGI that sends a temporary loading page to client then later sends the actual results page

  - by Kurt W. Leucht

  I've wasted at least a half day of my company's time searching the Internet for an answer and I'm getting wrapped around the axle here. I can't figure out the difference between all the different technology choices (long polling, ajax streaming, comet, XMPP, etc.) and I can't get a simple hello world example working on my PC. I am running Apache 2.2 and ActivePerl 5.10.0. JavaScript is completely acceptable for this solution. All I want to do is write a simple Perl CGI script that when accessed, it immediately returns some HTML that tells the user to wait or maybe sends an animated GIF. Then without any user intervention (no mouse clicks or anything) I want the CGI script to at some time later replace the wait message or the animated GIF with the actual HTML results from their query. I know this is simple stuff and websites do it all the time, but I can't find a single working example that I can cut and paste onto my machine that will work. Here is my simple Hello World example that I've compiled from various Internet sources, but it doesn't seem to work. When I refresh this CGI URL in my web browser it prints nothing for 5 seconds, then it prints the PLEASE BE PATIENT web page, but not the results web page. What am I doing wrong? #!C:\Perl\bin\perl.exe use CGI; use CGI::Carp qw/fatalsToBrowser warningsToBrowser/; sub Create_HTML { my $html = <<EOHTML; <html> <head> <meta http-equiv="pragma" content="no-cache" /> <meta http-equiv="expires" content="-1" /> <script type="text/javascript" > var xmlhttp=false; /*@cc_on @*/ /*@if (@_jscript_version >= 5) // JScript gives us Conditional compilation, we can cope with old IE versions. // and security blocked creation of the objects. try { xmlhttp = new ActiveXObject("Msxml2.XMLHTTP"); } catch (e) { try { xmlhttp = new ActiveXObject("Microsoft.XMLHTTP"); } catch (E) { xmlhttp = false; } } @end @*/ if (!xmlhttp && typeof XMLHttpRequest!='undefined') { try { xmlhttp = new XMLHttpRequest(); } catch (e) { xmlhttp=false; } } if (!xmlhttp && window.createRequest) { try { xmlhttp = window.createRequest(); } catch (e) { xmlhttp=false; } } </script> <title>Ajax Streaming Connection Demo</title> </head> <body> Some header text. <p> <div id="response">PLEASE BE PATIENT</div> <p> Some footer text. </body> </html> EOHTML return $html; } my $cgi = new CGI; print $cgi->header; print Create_HTML(); sleep(5); print "<script type=\"text/javascript\">\n"; print "\$('response').innerHTML = 'Here are your results!';\n"; print "</script>\n";

  Read the article

• jQuery DataTables server side processing and ASP.Net

  - by Chad

  I'm trying to use the server side functionality of the jQuery Datatables plugin with ASP.Net. The ajax request is returning valid JSON, but nothing is showing up in the table. I originally had problems with the data I was sending in the ajax request. I was getting a "Invalid JSON primative" error. I discovered that the data needs to be in a string instead of JSON serialized, as described in this post: http://encosia.com/2008/06/05/3-mistakes-to-avoid-when-using-jquery-with-aspnet-ajax/. I wasn't quite sure how to fix that, so I tried adding this in the ajax request: "data": "{'sEcho': '" + aoData.sEcho + "'}" If the aboves eventually works I'll add the other parameters later. Right now I'm just trying to get something to show up in my table. The returning JSON looks ok and validates, but the sEcho in the post is undefined, and I think thats why no data is being loaded into the table. So, what am I doing wrong? Am I even on the right track or am I being stupid? Does anyone ran into this before or have any suggestions? Here's my jQuery: $(document).ready(function() { $("#grid").dataTable({ "bJQueryUI": true, "sPaginationType": "full_numbers", "bServerSide":true, "sAjaxSource": "GridTest.asmx/ServerSideTest", "fnServerData": function(sSource, aoData, fnCallback) { $.ajax({ "type": "POST", "dataType": 'json', "contentType": "application/json; charset=utf-8", "url": sSource, "data": "{'sEcho': '" + aoData.sEcho + "'}", "success": fnCallback }); } }); }); HTML: <table id="grid"> <thead> <tr> <th>Last Name</th> <th>First Name</th> <th>UserID</th> </tr> </thead> <tbody> <tr> <td colspan="5" class="dataTables_empty">Loading data from server</td> </tr> </tbody> </table> Webmethod: <WebMethod()> _ Public Function ServerSideTest() As Data Dim list As New List(Of String) list.Add("testing") list.Add("chad") list.Add("testing") Dim container As New List(Of List(Of String)) container.Add(list) list = New List(Of String) list.Add("testing2") list.Add("chad") list.Add("testing") container.Add(list) HttpContext.Current.Response.ContentType = "application/json" Return New Data(HttpContext.Current.Request("sEcho"), 2, 2, container) End Function Public Class Data Private _iTotalRecords As Integer Private _iTotalDisplayRecords As Integer Private _sEcho As Integer Private _sColumns As String Private _aaData As List(Of List(Of String)) Public Property sEcho() As Integer Get Return _sEcho End Get Set(ByVal value As Integer) _sEcho = value End Set End Property Public Property iTotalRecords() As Integer Get Return _iTotalRecords End Get Set(ByVal value As Integer) _iTotalRecords = value End Set End Property Public Property iTotalDisplayRecords() As Integer Get Return _iTotalDisplayRecords End Get Set(ByVal value As Integer) _iTotalDisplayRecords = value End Set End Property Public Property aaData() As List(Of List(Of String)) Get Return _aaData End Get Set(ByVal value As List(Of List(Of String))) _aaData = value End Set End Property Public Sub New(ByVal sEcho As Integer, ByVal iTotalRecords As Integer, ByVal iTotalDisplayRecords As Integer, ByVal aaData As List(Of List(Of String))) If sEcho <> 0 Then Me.sEcho = sEcho Me.iTotalRecords = iTotalRecords Me.iTotalDisplayRecords = iTotalDisplayRecords Me.aaData = aaData End Sub Returned JSON: {"__type":"Data","sEcho":0,"iTotalRecords":2,"iTotalDisplayRecords":2,"aaData":[["testing","chad","testing"],["testing2","chad","testing"]]}

  Read the article

• ASP .NET 2.0 C# AjaxPro RegisterTypeForAjax

  - by Dan7el

  I am wondering if RegisterTypeForAjax isn't working correctly. I am getting the error noted at the end of the code block below. Sample is from here: http://www.ajaxtutorials.com/asp-net-ajax-quickstart/tutorial-introduction-to-ajax-in-asp-net-2-0-and-c/ Any ideas as to why I'm getting this error? Thanks. ASP .NET 2.0 C# Here is the code-behind: using System; using System.Data; using System.Data.SqlClient; using System.Configuration; using System.Collections; using System.Collections.Generic; using System.Web; using System.Web.Security; using System.Web.UI; using System.Web.UI.WebControls; using System.Web.UI.WebControls.WebParts; using System.Web.UI.HtmlControls; using AjaxPro; namespace WebApplication1 { public partial class Ajax_CSharp : System.Web.UI.Page { protected override void OnInit( EventArgs e ) { base.OnInit( e ); Load += new EventHandler( Page_Load ); } protected void Page_Load( object sender, EventArgs e ) { Utility.RegisterTypeForAjax( typeof( Ajax_CSharp ) ); } [ AjaxMethod( HttpSessionStateRequirement.ReadWrite ) ] public string GetData() { // method gets a row from the db and returns a string. } } Here is the ASPX page: <%@ Page Language="C#" AutoEventWireup="false" CodeBehind="Default.aspx.cs" Inherits="WebApplication1.Ajax_CSharp" % Untitled Page function GetData() { var response; Ajax_CSharp.GetData( GetData_CallBack ); } function GetData_CallBack( response ) { var response = response.value; if ( response == "Empty" ) { alert( "No Record Found." ); } else if ( response == "Error" ) { alert( "An Error Occurred in Accessing the Database !!!" ); } else { var arr = response.split( "~" ); var empID = arr[0].split( "," ); var empName = arr[1].split( "," ); document.getElementById( 'dlistEmployee' ).length = 0; for ( var i = 0; i < empID.Length; i++ ) { var o = document.createElement( "option" ); o.value = empID[i]; o.text = empName[i]; document.getElementById( 'dlistEmployee' ).add( o ); } } } function dodisplay() { var selIndex = document.getElementById( "dlistEmployee" ).selectedIndex; var empName = document.getElementById( "dlistEmployee" ).options( selIndex ).text; var empID = document.getElementById( "dlistEmployee" ).options( selIndex ).value; document.getElementById( "lblResult" ).innerHTML = "You have selected " + empName + " (ID: " + empID + " )"; } </script>    Run it and click on the button and I get this error: Webpage error details User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 5.1; Trident/4.0; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; InfoPath.2; MS-RTC LM 8) Timestamp: Mon, 26 Apr 2010 17:22:44 UTC Message: 'Ajax_CSharp' is undefined Line: 13 Char: 11 Code: 0 URI: http://localhost:4678/Default.aspx

  Read the article

< Previous Page | 488 489 490 491 492 493 494 495 496 497 498 499  | Next Page >