Search Results

Search found 26692 results on 1068 pages for 'virtual private cloud'.

Page 495/1068 | < Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >

  • special case ssh connection lag

    - by Hersheezy
    Setup We have a DMZ and LAN in our office that are connected to the outside with the following setup: +------+ | |------> LAN (normal office router) |Modem | | |------> DMZ (a single machine) +------+ Our internet account is with Comcast and we have 5 status IPs, one of which points to the single machine in the DMZ. Problem ssh connections initiated ANYWHERE EXCEPT the office LAN are really fast. However, from the LAN, there is about a 5 second delay. WTF?? Extra info The DMZ machine is debian 5. Executing a wget to the DMZ has no lag. When executing the following, everything up to HERE IS WHERE THE LAG IS INCURRED executes immediately. ssh -vvvv [email protected] ... debug2: set_newkeys: mode 1 debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug3: Wrote 16 bytes for a total of 1015 debug2: set_newkeys: mode 0 debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug3: Wrote 48 bytes for a total of 1063 debug2: service_accept: ssh-userauth debug1: SSH2_MSG_SERVICE_ACCEPT received debug2: key: /home/shopkins/.ssh/id_rsa (0x22440830) debug2: key: /home/shopkins/.ssh/identity ((nil)) debug2: key: /home/shopkins/.ssh/id_dsa ((nil)) debug3: Wrote 64 bytes for a total of 1127` HERE IS WHERE THE LAG IS INCURRED debug1: Authentications that can continue: publickey,password debug3: start over, passed a different list publickey,password debug3: preferred gssapi-keyex,gssapi-with-mic,gssapi,publickey,keyboard-interactive,password debug3: authmethod_lookup publickey debug3: remaining preferred: keyboard-interactive,password debug3: authmethod_is_enabled publickey debug1: Next authentication method: publickey debug1: Offering public key: /home/shopkins/.ssh/id_rsa debug3: send_pubkey_test debug2: we sent a publickey packet, wait for reply debug3: Wrote 368 bytes for a total of 1495 debug1: Authentications that can continue: publickey,password debug1: Trying private key: /home/shopkins/.ssh/identity debug3: no such identity: /home/shopkins/.ssh/identity debug1: Trying private key: /home/shopkins/.ssh/id_dsa debug3: no such identity: /home/shopkins/.ssh/id_dsa debug2: we did not send a packet, disable method debug3: authmethod_lookup password debug3: remaining preferred: ,password debug3: authmethod_is_enabled password debug1: Next authentication method: password [email protected]'s password:

    Read the article

  • Mac Mini server (10.6) behind router with FQDN hostname

    - by thechriskelley
    I have a Mac Mini running Mac OS 10.6.6 Server that will be part of a local network, and a static IP from my ISP. I'd like to set up DNS for the Mini with a FQDN as the hostname (example.com) properly. The Mini is behind a router (Apple Airport Extreme) and is given a private, static IP address. I can't assign it the public static IP directly because it's behind a router with DHCP/NAT for other machines on the local net. My end goal here is for services to resolve to the server properly from outside and inside the local network to users via example.com (and subdomains like mail.example.com, www.example.com), which will point to the public static IP assigned to the router. Will DNS work/resolve properly (for mail services and other subdomains) if it has a private ip address, but the necessary services are forwarded properly through NAT? I'm open to any (hopefully better) suggestions, as my current setup doesn't seem like it's the best way. Currently, more hardware or another public static IP is not possible. With the current setup, it seems as though one static IP is not necessary anyway. Thanks in advance for any insight.

    Read the article

  • Printing to a Windows 7 incompatible printer shared on supported Windows XP machine

    - by MGSoto
    I have an HP Laserjet 1500 that is supported by Windows XP, but not supported by Windows-7. I want to print from my 7 machine(s) to my XP machine on this printer. Is there some sort of way to send a generic job (like sending raw postscript or something) to the XP machine, which will then print it with the proper drivers? Is there a virtual printer that has drivers for both XP and 7 that will just re-print it on the XP machine using the real printer?

    Read the article

  • Assign fixed IP address via DHCP by DNS lookup

    - by Janoszen
    Preface I'm building a virtualization environment with Ubuntu 14.04 and LXC. I don't want to write my own template since the upgrade from 12.04 to 14.04 has shown that backwards compatibility is not guaranteed. Therefore I'm deploying my virtual machines via lxc-create, using the default Ubuntu template. The DNS for the servers is provided by Amazon Route 53, so no local DNS server is needed. I also use Puppet to configure my servers, so I want to keep the manual effort on the deployment minimal. Now, the default Ubuntu template assigns IP addresses via DHCP. Therefore, I need a local DHCP server to assign IP addresses to the nodes, so I can SSH into them and get Puppet running. Since Puppet requires a proper DNS setup, assigning temporary IP addresses is not an option, the client needs to get the right hostname and IP address from the start. Question What DHCP server do I use and how do I get it to assign the IP address based only on the host-name DHCP option by performing a DNS lookup on that very host name? What I've tried I tried to make it work using the ISC DHCP server, however, the manual clearly states: Please be aware that only the dhcp-client-identifier option and the hardware address can be used to match a host declaration, or the host-identifier option parameter for DHCPv6 servers. For example, it is not possible to match a host declaration to a host-name option. This is because the host-name option cannot be guaranteed to be unique for any given client, whereas both the hardware address and dhcp-client-identifier option are at least theoretically guaranteed to be unique to a given client. I also tried to create a class that matches the hostname like this: class "my-client-name" { match if option host-name = "my-client-name"; fixed-address my-client-name.my-domain.com; } Unfortunately the fixed-address option is not allowed in class statements. I can replace it with a 1-size pool, which works as expected: subnet 10.103.0.0 netmask 255.255.0.0 { option routers 10.103.1.1; class "my-client-name" { match if option host-name = "my-client-name"; } pool { allow members of "my-client-name"; range 10.103.1.2 10.103.1.2; } } However, this would require me to administer the IP addresses in two places (Amazon Route53 and the DHCP server), which I would prefer not to do. About security Since this is only used in the bootstrapping phase on an internal network and is then replaced by a static network configuration by Puppet, this shouldn't be an issue from a security standpoint. I am, however, aware that the virtual machine bootstraps with "ubuntu:ubuntu" credentials, which I intend to fix once this is running.

    Read the article

  • How to boot linux direct to application on console with no login

    - by amanda
    I have a need to start an application on bootup on the linux console and I do not have a need for any type of login or security. I do not need any ALT-F1,F2,etc virtual consoles but I would like to allow SSH access via the network port for debugging, loading, etc. The application is a SDL graphics program running with fbcon as the SDL_VIDEODRIVER if that matters. I'm currently using Fedora 10 and 12 but any distro that supports SDL using the fbcon framebuffer would be acceptable.

    Read the article

  • use ubuntu server 10.4 as a virtulization server as esx from VMWare

    - by hitham
    i was wondering if its possible to use Ubuntu server as virtualization center as esxi vmware i am asking this coz i read this in ubuntu website: " Ubuntu includes a Virtual Machine Builder which makes this process simple and replicable allowing multiple pre-configured machines to be deployed instantly ". if its possible how can i do such thing ?. with all respect . Hitham Melhem

    Read the article

  • ISA 2006 Ent with NLB configuration

    - by Nagori
    Hello We have created to virtual machines and installed ISA 2006 Ent and enable NLB configuration, each machine has two NIC one connected to LAN and other connected to DMZ, we are not able to ping DMZ subnet IP of ISA from another machine which is on same DMZ subnet even though we have diable the all ISA services (including firewall). But we can ping LAN IP from all our internal subnets and this ping is working with ISA services are started or stop status Thank you

    Read the article

  • Mac OS X 10.6.3: how does Apache config work?

    - by w-
    Just got a MacBook Pro 15" so I'm unfamiliar with how the filesystem is laid out. I noticed when in my filesystem that I've got a few paths specifying httpd.conf: /etc/apache2/httpd.conf /opt/local/apache2/conf/httpd.conf /private/etc/apache2/httpd.conf The config files are different in lots of ways (user, group, server_root, modules that are loaded, etc.) The apache2 folders themselves also greatly differ. It seems that the one getting used is either /etc/apache2/httpd.conf or /private/etc/apache2/httpd.conf I'm wondering if I might have messed up my system after installing some packages (php5, django, etc) via macports and maybe ended up with 2 apache2 instances. My questions are hence: which httpd.conf is the one being used ? what are the other files for? thanks --update-- To clarify, I didn't explicitly install apache2 via macports. I'm wondering if it was installed because it was a dependency. After more hunting around I'm learning I never should've installed php to begin with because Snow Leopard already includes php 5.3 from the get go. http://serverfault.com/questions/82410/apache-2-and-php-5-3-via-macports I'll need to open another question that asks about how the Mac filesystem works. Thanks all for replies.

    Read the article

  • Allowing access to subnets openvpn access server

    - by user3882976
    I have a centos server running a openvpn access server. On that server I am running a windows server in virtual box. On the centos server I am running the vpn with a network address 172.27.224.0 with 20 bits. The windows server is running a dchp server giving ip's of 192.168.1.0-200. When i try to connect to the widows shared folder from the vpn i can't using the name of the server but i can from the ip.

    Read the article

  • Does Windows 7 RC handle non Windows Media Center remotes yet?

    - by zillion
    I'm mostly a Linux geek, but while I will be trying to make my first Arch Linux installation in a virtual machine to learn and make my installation script for the true install, I need a simple OS and Windows 7 was better than Windows XP Media Center cause Media Center is outdated on XP. I tested it has a beta but my Hauppauge wintv-pvr usb2 remote wasn't working but the tv-tuner worked well and I haven't tested Windows XP Mode and my printer Epson Stylus Photo R300. Do someone know this hardware and if the XP Mode is easily supported?

    Read the article

  • iso is already present on server

    - by andygriff
    Hi, I'm using SCVMM R2 with Windows 2008 R2 hosts. I've noticed that if I have an iso mounted on a vm from the scvmm library and then a snapshot is restored then you always get an error .iso is already present on server when trying add it again. I know you can log onto the Host and delete the iso from the Virtual Machine foler but that will be a nigthmare in a 200 VM strong implimentation. is there another way?

    Read the article

  • Best way to monitor a Grid of computers?

    - by marc.riera
    I've installed Sun Grid Engine on 10 nodes, and one virtual master host. Now I have to monitor all the resources prior to launching it into production, but I don't know which is the best way. I've tried using xml-qstat, but it seems unstable. Any tips or suggestions? Anyone got experience on this? thanks.

    Read the article

  • How can I get my routers to forward ports correctly?

    - by Giffyguy
    My network currently looks like this (simplified): Note that Router #2 is connected to the LAN interface of Router #1. This should be familiar to anyone who has seen a standard static-IP setup with an additional firewall for a residence or other small building. Router #1 is actually my cable gateway, but since it is a fully functional router/firewall, I am going to refer to it as a router. Now, I need to open various ports in both firewalls for incoming communication to my server - port 80 is a good example. So I've opened up port 80 in Router #2, and so far all incoming traffic at the public IP X.X.X.129 is being routed correctly. The problem is that I also need my server to respond to incoming traffic at the public IP X.X.X.130 on the WAN interface of Router #1. Naturally, I can't just tell Router #1 to forward port 80 to another public IP. Port forwarding is only supported when the traffic is being directed to the LAN subnet. I am willing to restructure my network topology if required, with the following conditions: Router #1 cannot have its WAN IP reassigned - X.X.X.130 is mandatory. Router #1 cannot be moved or disconnected from the cloud. The server cannot be given a second IP address. I would prefer the server to have a private IP address - e.g. 10.0.0.10 I'd like to keep Router #2, but it can have a private IP - e.g. 10.0.1.10 Following these rules, I need to get my server to receive incoming traffic on port 80 from both public IP addresses. Does anyone on SU know if this is possible? So far my only theories have been to set up a static route on either router, or to somehow combine my two subnets into a single subnet.

    Read the article

  • Any online network topology to study?

    - by Gok Demir
    I want to study network. But I don't have an access to a sample network (routers, DNS, IP4, IP6 windows linux mixed heterogenous system). Do you know any online network to study (Free as possible). Is it possible to simulate network topologies with a sing PC using virtual machine. If so could you guide me?

    Read the article

  • Custom initrd init script: how to create /dev/initctl

    - by Posco Grubb
    I have a virtual machine (VMM is Xen 3.3) equipped with two IDE HDD's (/dev/hda and /dev/hdb). The root file system is in /dev/hda1, where Scientific Linux 5.4 is installed. /dev/hdb contains an empty ext2 file system. I want to protect the root file system from writes by the VM by using aufs (AnotherUnionFS) to layer a writable file system on top of the root file system. The changes to / will be written to the file system located on /dev/hdb. (Furthermore, outside the VM, the file backing the /dev/hda will also be set to read-only permissions, so the VMM should also prevent the VM from modifying at that level.) (The purpose of this setup: be able to corrupt a virtual machine using software-implemented fault injection but preserve the file system image in order to quickly reboot the VM to a fault-free state.) How do I get an initrd init script to do the necessary mounts to create the union file system? I've tried 2 approaches: I've tried modifying the nash script that mkinitrd creates, but I don't know what setuproot and switchroot do and how to make them use my aufs as the new root. Apparently, nobody else here knows either. (EDIT: I take that back.) I've tried building a LiveCD (using linux-live-6.3.0) and then modifying the Bash /linuxrc script from the generated initrd, and I got the mounts correct, but the final /sbin/init complains about /dev/initctl. Specifically, my /linuxrc mounts the aufs at /union. The last few lines of /linuxrc effectively do the following: cd /union mkdir -p mnt/live pivot_root . mnt/live exec sbin/chroot . sbin/init </dev/console >/dev/console 2>&1 When init starts, it outputs something like init: /dev/initctl: No such file or directory. What is supposed to create this FIFO? I found no such filename in the original linuxrc and liblinuxlive scripts. I tried creating it via "mkfifo /dev/initctl", but then init complained about a timeout opening or writing to the FIFO. Would appreciate any help or pointers. Thanks.

    Read the article

  • Error activating XKB configuration (Ubuntu 9.10)?

    - by Mohammad
    I'm absolutely new on Ubuntu. I was gonna learn Ubuntu, so I installed VMware 7.0.1 build-227600 on my Win7 x64, afterward I've installed Ubuntu 9.10 on it as a Virtual Machine. I just enabled root account, and when I log in as root for once, I received the following error : What's wrong with it? Am I miss something?

    Read the article

  • Zyxel P-320W: How to connect to my web server using public IP

    - by hvtuananh
    My company's router is Zyxel P-320W and I have a public static IP. I registered a few domains name and point to this IP address. I already setup Virtual Hosts and configured port-forwarding to my internal server and it works well. I can connect to all domains from outside The problem is I cannot connect to my domains from inside One workaround way is modify hosts file to add internal IP for those domains, but my company have many computers and I don't want to setup all PC manually

    Read the article

  • Zyxel P-320W: How to connect to my web server using public IP

    - by hvtuananh
    My company's router is Zyxel P-320W and I have a public static IP. I registered a few domains name and point to this IP address. I already setup Virtual Hosts and configured port-forwarding to my internal server and it works well. I can connect to all domains from outside The problem is I cannot connect to my domains from inside One workaround way is modify hosts file to add internal IP for those domains, but my company have many computers and I don't want to setup all PC manually

    Read the article

  • ssh timeout issue connecting to an EC2 instance on OS X

    - by mamusr
    I am new to AWS and not a networking expert but curious to know more about it. I created a VPC with a public subnet only. Then i created an EC2 instance using an Ubuntu 14.04 64-bit pv AMI image (ami-e84d8480) as well generating the key pair needed to connect to it through ssh. I followed amazon's instructions to connect to an EC2 instance via ssh which did not work. Here is my attempted input and debug log: Running on OS X 10.9.4 user$ ssh -vvv -i key.pem [email protected] OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: /etc/ssh_config line 102: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to xxx.xxx.xxx.xxx [xxx.xxx.xxx.xxx] port 22. debug1: connect to address xxx.xxx.xxx.xxx port 22: Operation timed out ssh: connect to host xxx.xxx.xxx.xxx port 22: Operation timed out To attempt to resolve the issue: I enabled the SSH port. Tried different usernames other than ubuntu, like ec2-user and root. Initially set an inbound ssh rule in the security group to connect to only my ip address. When that did not work, i changed it to allow any ip to connect. But those actions did not fix the problem. Here are my guesses as to what i am missing in getting the EC2 instance connection to work. My etc/ssh_config file may be preventing the connection from taking place. I may have missed an important networking detail when setting up the VPC. I do not have a public ip address specified for the instance. I am connecting through the private ip address. My questions for the community: Am i going about it the wrong way connecting to the instance through the private ip address? if so, do i need to specify a public ip address for it to connect or some other method?

    Read the article

  • Email test deferred (mail transport unavailable) with ClamAV

    - by dirt
    I'm trying to set up a simple new mail server; when I send a test email to the server the email is getting hung up during delivery (user mapping is found) and the email is never found in /home/user/Maildir/new Here is my maillog after a fresh reboot and test email, there are a few warnings I am unfamiliar with. Can you please point me in the right direction? Oct 25 14:54:57 loki dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Oct 25 14:54:58 loki postfix/postfix-script[1369]: starting the Postfix mail system Oct 25 14:54:58 loki postfix/master[1370]: daemon started -- version 2.6.6, configuration /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: request to update table btree:/etc/postfix/smtpd_scache in non-postfix directory /etc/postfix Oct 25 14:56:00 loki postfix/tlsmgr[1457]: warning: redirecting the request to postfix-owned data_directory /var/lib/postfix Oct 25 14:56:00 loki postfix/smtpd[1455]: connect from mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/smtpd[1455]: 1CF5E20A8B: client=mail-ob0-f180.google.com[209.85.214.180] Oct 25 14:56:01 loki postfix/cleanup[1461]: 1CF5E20A8B: message-id= Oct 25 14:56:01 loki postfix/qmgr[1379]: 1CF5E20A8B: from=, size=1788, nrcpt=1 (queue active) Oct 25 14:56:01 loki postfix/qmgr[1379]: warning: connect to transport private/scan: No such file or directory Oct 25 14:56:01 loki postfix/error[1462]: 1CF5E20A8B: to=, orig_to=, relay=none, delay=0.18, delays=0.15/0.02/0/0.01, dsn=4.3.0, status=deferred (mail transport unavailable) Oct 25 14:56:01 loki postfix/smtpd[1455]: disconnect from mail-ob0-f180.google.com[209.85.214.180] master.cf snippets: # ========================================================================== # service type private unpriv chroot wakeup maxproc command + args # (yes) (yes) (yes) (never) (100) # ========================================================================== smtp inet n - n - - smtpd submission inet n - n - - smtpd -o smtpd_tls_security_level=encrypt # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING smtps inet n - n - - smtpd -o smtpd_tls_wrappermode=yes # -o smtpd_sasl_auth_enable=yes # -o smtpd_client_restrictions=permit_sasl_authenticated,reject # -o milter_macro_daemon_name=ORIGINATING scan unix - - n - 16 smtp -o smtp_data_done_timeout=1200 -o smtp_send_xforward_command=yes -o disable_dns_lookups=yes 127.0.0.1:10026 inet n - n - 16 smtpd -o content_filter= -o local_recipient_maps= -o relay_recipient_maps= -o smtpd_restriction_classes= -o smtpd_client_restrictions= -o smtpd_helo_restrictions= -o smtpd_sender_restrictions= -o smtpd_recipient_restrictions=permit_mynetworks,reject -o mynetworks_style=host -o smtpd_authorized_xforward_hosts=127.0.0.0/8

    Read the article

  • Split horizon, route filtering, and having RIPv2 announce a non-attached route to host...

    - by Paul
    Routers A, B & C live at 10.1.1.1, 10.1.1.2 and 10.1.1.3 on a /24 metro Ethernet subnet. Each router also has its own private subnet on another interface. Router B's private subnet links thru a firewall to a 10.20.20.0 network at another organization. Router B redistributes to A and C several static routes for hosts on 10.20.20.0. However, a new host 10.20.20.5/32 must be reached via a different path that goes through router C. I know that C can advertise this host-based route with no problem, but I'd like to keep all my 10.20.20.x static routes in one place. So, how can B tell A via RIPv2 to send packets for 10.20.20.5/32 to C? So far it looks like I need no ip split-horizon on router B's 10.1.1.2 interface, perhaps because B has already learned from C other routes with a next hop of 10.1.1.3. But how does RIPv2 split horizon with no auto-summary and network 10.0.0.0 really work? If B learns a route to ANY 10.x.x.x network or host from A or C, is that enough for split horizon to keep it from redistributing ip route 10.20.20.5 255.255.255.255 10.1.1.3? And if I want to suspend split horizon only for this one new host, how do I filter out the mess of regurgitated routes that B advertises when I try no ip split-horizon? Thanks much.

    Read the article

  • Use ubuntu server 10.04 as a virtulization server as esxi from VMWare

    - by hitham
    I was wondering if its possible to use Ubuntu server as virtualization center as ESXi Vmware? I am asking this coz i read this in ubuntu website: "Ubuntu includes a Virtual Machine Builder which makes this process simple and replicable allowing multiple pre-configured machines to be deployed instantly". If its possible how can i do such thing?. with all respect. Hitham Melhem

    Read the article

< Previous Page | 491 492 493 494 495 496 497 498 499 500 501 502  | Next Page >