Search Results

Search found 13518 results on 541 pages for 'daniel root'.

Page 496/541 | < Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >

• SCVMM 2012 R2 - Installing Virtual Switch Fails with Error 2916

  - by Brian M.

  So I've been attempting to teach myself SCVMM 2012 and Hyper-V Server 2012 R2, and I seem to have hit a snag. I've connected my Hyper-V Host to SCVMM 2012 successfully, and created a logical network, logical switch, and uplink port profile (which I essentially blew through with the default settings). However when I attempt to create a virtual switch on my Hyper-V host, I run into an issue. The job will use my logical network settings I created to configure the virtual switch, but when it tries to apply it to the host, it stalls and eventually fails with the following error: Error (2916) VMM is unable to complete the request. The connection to the agent vmhost1.test.loc was lost. WinRM: URL: [h**p://vmhost1.test.loc:5985], Verb: [GET], Resource: [h**p://schemas.microsoft.com/wbem/wsman/1/wmi/root/virtualization/v2/Msvm_ConcreteJob?InstanceID=2F401A71-14A2-4636-9B3E-10C0EE942D33] Unknown error (0x80338126) Recommended Action Ensure that the Windows Remote Management (WinRM) service and the VMM agent are installed and running and that a firewall is not blocking HTTP/HTTPS traffic. Ensure that VMM server is able to communicate with econ-hyperv2.econ.loc over WinRM by successfully running the following command: winrm id –r:vmhost1.test.loc This problem can also be caused by a Windows Management Instrumentation (WMI) service crash. If the server is running Windows Server 2008 R2, ensure that KB 982293 (h**p://support.microsoft.com/kb/982293) is installed on it. If the error persists, restart vmhost1.test.loc and then try the operation again. Refer to h**p://support.microsoft.com/kb/2742275 for more details. I restarted the server, and upon booting am greeted with a message stating "No active network adapters found." I load up powershell and run "Get-NetAdapter -IncludeHidden" to see what's going on, and get the following: Name InterfaceDescription ifIndex Status ---- -------------------- ------- ----- Local Area Connection* 5 WAN Miniport (PPPOE) 6 Di... Ethernet Microsoft Hyper-V Network Switch Def... 10 Local Area Connection* 1 WAN Miniport (L2TP) 2 Di... Local Area Connection* 8 WAN Miniport (Network Monitor) 9 Up Local Area Connection* 4 WAN Miniport (PPTP) 5 Di... Ethernet 2 Broadcom NetXtreme Gigabit Ethernet 13 Up Local Area Connection* 7 WAN Miniport (IPv6) 8 Up Local Area Connection* 9 Microsoft Kernel Debug Network Adapter 11 No... Local Area Connection* 3 WAN Miniport (IKEv2) 4 Di... Local Area Connection* 2 WAN Miniport (SSTP) 3 Di... vSwitch (TEST Test Swi... Hyper-V Virtual Switch Extension Ada... 17 Up Local Area Connection* 6 WAN Miniport (IP) 7 Up Now the machine is no longer visible on the network, and I don't have the slightest idea what went wrong, and more importantly how to undo the damage I caused in order to get back to where I was (save for re-installing Hyper-V Server, but I really would rather know what's going on and how to fix it)! Does anybody have any ideas? Much appreciated!

  Read the article

• PHP bcompiler install

  - by dobs

  How to install bcompiler on Fedora, have this error: [root@server server]# pecl install channel://pecl.php.net/bcompiler-0.9.1 downloading bcompiler-0.9.1.tgz ... Starting to download bcompiler-0.9.1.tgz (47,335 bytes) .............done: 47,335 bytes 10 source files, building running: phpize Configuring for: PHP Api Version: 20090626 Zend Module Api No: 20090626 Zend Extension Api No: 220090626 building in /var/tmp/pear-build-server/bcompiler-0.9.1 running: /var/tmp/bcompiler/configure checking for grep that handles long lines and -e... /bin/grep checking for egrep... /bin/grep -E checking for a sed that does not truncate output... /bin/sed checking for cc... cc checking whether the C compiler works... yes checking for C compiler default output file name... a.out checking for suffix of executables... checking whether we are cross compiling... no checking for suffix of object files... o checking whether we are using the GNU C compiler... yes .... /var/tmp/bcompiler/bcompiler.c:2174: ?????????: expected ‘struct zend_arg_info *’ but argument is of type ‘const struct _zend_arg_info *’ /var/tmp/bcompiler/bcompiler.c: ? ??????? ‘apc_serialize_zend_class_entry’: /var/tmp/bcompiler/bcompiler.c:3100: ??????????????: ???????????? ???????? ????????????? ?????????? ???? /var/tmp/bcompiler/bcompiler.c:3107: ??????????????: ???????? ????????? 1 ‘apc_serialize_zend_function_entry’ ???????? ????????????? ?????????? ???? /var/tmp/bcompiler/bcompiler.c:2874: ?????????: expected ‘struct zend_function_entry *’ but argument is of type ‘const struct _zend_function_entry *’ /var/tmp/bcompiler/bcompiler.c: ? ??????? ‘apc_deserialize_zend_class_entry’: /var/tmp/bcompiler/bcompiler.c:3324: ??????????????: ???????? ????????? 1 ‘apc_deserialize_zend_function_entry’ ???????? ????????????? ?????????? ???? /var/tmp/bcompiler/bcompiler.c:2900: ?????????: expected ‘struct zend_function_entry *’ but argument is of type ‘const struct _zend_function_entry *’ make: *** [bcompiler.lo] ?????? 1 ERROR: 'make' failed yum install bzip2-libs bzip2-devel - Fix it...

  Read the article

• Programmatically add an ISAPI extension dll in IIS 7 using ADSI?

  - by fretje

  I apologize beforehand, this is a cross post of this SO question. I thought I'd ask it there first, but apparently it doesn't harvest any answers there. I hope it will get more attention here. When I have an answer somewhere, I'll delete the other one. I'm trying to programmatically add an ISAPI extension dll in IIS using ADSI. This has been working for ages on previous versions of IIS, but it seems to fail on IIS 7. I am using similar code like shown in this question: var web = GetObject("IIS://localhost/W3SVC/1/ROOT/specificVirtualDirectory"); var maps = web.ScriptMaps.toArray(); map[maps.length] = ".aaa,c:\\path\\to\\isapi\\extension.dll,1,GET,POST"; web.ScriptMaps = maps.asDictionary(); web.SetInfo(); After executing that code, I do see an "AboMapperCustom-12345678" entry for that specific dll in the "Handler mappings" of the specific virtual directory in which I added the script map. But when I try to use that extension in a browser, I always get HTTP Error 404.2 Not Found The page you are requesting cannot be served because of the ISAPI and CGI Restriction list settings on the Web server. Even after adding an entry to allow that specific dll in the "ISAPI and CGI restrictions", I keep getting that error. To make it actually work, I first have to undo these steps (encountering the same issue like the OP of the question mentioned above: after deleting the script map entry from the IIS manager GUI, I also have to programmatically delete it using ADSI before it's actually gone from the metabase). And then manually add an entry like this: inetmgr - webserver - website - virtual directory - handler mappings - add script map... path = *.dll, executable = <path to dll>, name = <doesn't matter, but it's mandatory> click "yes" on the question "do you want to allow this ISAPI extension?" When I compare the 2 entries, they are exactly the same, except for the "Entry Type" which seems to be "Inherited" for the programmatically added one and "Local" for the one added manually. The strange thing is, even though it says "Inherited", I don't see it anywhere in IIS on a higher level. Where is it inheriting from? In my code, I do add the script map to the specific virtual directory so it should be "Local" as well. Maybe there is the problem, but I don't know how to add a "Local" Script Map using ADSI. I really would like to keep using the ADSI method, as otherwise I will have to use different methods in our setup when working with IIS 7 or previous versions, and I would like to avoid that. To recap: How can I programmatically add a script map entry and its companion CGI and ISAPI restrictions entry to IIS 7 using ADSI? Anybody who can shed some light on this? Any help appreciated.

  Read the article

• How do I get a .Net 4.0 app to coexist as an application under a SharePoint 2007 website in IIS v7?

  - by Craig Nakamoto

  I have created a small .Net 4.0 website and installed it on my SharePoint server as a separate web site in IIS v7 (using port 8008 for now). I had to install the .Net 4 framework, set up the database, etc. and this all went smoothly and my app works as a standalone website. Now I am trying to get pages from my website to show up in SharePoint 2007. For various reasons (the SharePoint site is using SSL, security, etc.) I now need to move my .Net app to run under the SharePoint 2007 site in IIS. I have added it as an 'Application' and set it up with the same .Net v4 application pool and settings that were working when it was set up as a standalone site. Now when I try to access the application I get the error at the end of this description. Any help would be greatly appreciated. I already tried following the instructions on this post: http://blogs.msdn.com/sgoodyear/archive/2007/05/07/custom-web-applications-coexisting-with-sharepoint-2007.aspx but that did not help. Thanks! Craig p.s. Here are the error details: Log Name: Application Source: ASP.NET 4.0.30319.0 Date: 11/05/2010 11:49:31 AM Event ID: 1310 Task Category: Web Event Level: Warning Keywords: Classic User: N/A Computer: GGI-SP1.ggi.ca Description: Event code: 3008 Event message: A configuration error has occurred. Event time: 11/05/2010 11:49:31 AM Event time (UTC): 11/05/2010 3:49:31 PM Event ID: 559d7ac619344f3499a4a31c6c9e58cd Event sequence: 1 Event occurrence: 1 Event detail code: 0 Application information: Application domain: /LM/W3SVC/1653978112/ROOT/bidmonitor-1-129180665715766107 Trust level: Application Virtual Path: /bidmonitor Application Path: C:\inetpub\wwwroot\bidmonitor\ Machine name: GGI-SP1 Process information: Process ID: 5272 Process name: w3wp.exe Account name: NT AUTHORITY\NETWORK SERVICE Exception information: Exception type: ConfigurationErrorsException Exception message: Could not find permission set named 'ASP.Net'. at System.Web.Hosting.ApplicationManager.CreateAppDomainWithHostingEnvironment(String appId, IApplicationHost appHost, HostingEnvironmentParameters hostingParameters) at System.Web.HttpRuntime.HostingInit(HostingEnvironmentFlags hostingFlags, PolicyLevel policyLevel, Exception appDomainCreationException) Request information: Request URL: gginet.ggi.ca/bidmonitor Request path: /bidmonitor User host address: 10.10.1.33 User: Is authenticated: False Authentication Type: Thread account name: NT AUTHORITY\NETWORK SERVICE Thread information: Thread ID: 3 Thread account name: NT AUTHORITY\NETWORK SERVICE Is impersonating: False Stack trace: at System.Web.HttpRuntime.HostingInit(HostingEnvironmentFlags hostingFlags, PolicyLevel policyLevel, Exception appDomainCreationException)

  Read the article

• Globe SSL with NGINX SSL certificate problem, please help

  - by PartySoft

  I have a big problem with installing a certificat for nginx (same happends with apache though) I have 3 files __domain_com.crt __domain_com.ca-bundle and ssl.key. I tried to append cat __domain_com.crt __leechpack_com.ca-bundle bundle.crt but if I do it like this i get an error: [emerg]: SSL_CTX_use_certificate_chain_file("/etc/nginx/__leechpack_com.crt") failed (SSL: error:0906D066:PEM routines:PEM_read_bio:bad end line error:140DC009:SSL routines:SSL_CTX_use_certificate_chain_file:PEM lib) And that's because the delimiters of the certificates arren't separated. ZqTjb+WBJQ== -----END CERTIFICATE----------BEGIN CERTIFICATE----- MIIE6DCCA9CgAwIBAgIQdIYhlpUQySkmKUvMi/gpLDANBgkqhkiG9w0BAQUFADBv If i separate them with an enter between certificated it will at least start but i will get the same warning from Firefox: This Connection is Untrusted You have asked Firefox to connect securely to domain.com, but we can't confirm that your connection is secure. The concatenate solution it is given by Globe SSL and the NGINX site but it doesn't work. I think the bundle is ignored though. http://customer.globessl.com/knowledgebase/55/Certificate-Installation--Nginx.html http://nginx.org/en/docs/http/configuring_https_servers.html#chains%20http://wiki.nginx.org/NginxHttpSslModule if i do openssl s_client -connect down.leechpack.com:443 CONNECTED(00000003) depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=20:unable to get local issuer certificate verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=27:certificate not trusted verify return:1 depth=0 /OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com verify error:num=21:unable to verify the first certificate verify return:1 --- Certificate chain 0 s:/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com i:/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA 1 s:/C=US/O=Globe Hosting, Inc./OU=GlobeSSL DV Certification Authority/CN=GlobeSSL CA i:/C=SE/O=AddTrust AB/OU=AddTrust External TTP Network/CN=AddTrust External CA Root --- Server certificate -----BEGIN CERTIFICATE----- MIIFQzCCBCugAwIBAgIQRnpCmtwX7z7GTla0QktE6DANBgkqhkiG9w0BAQUFADBl MQswCQYDVQQGEwJSTzEuMCwGA1UEChMlR0xPQkUgSE9TVElORyBDRVJUSUZJQ0FU SU9OIEFVVEhPUklUWTEmMCQGA1UEAxMdR0xPQkUgU1NMIERvbWFpbiBWYWxpZGF0 ZWQgQ0EwHhcNMTAwMjExMDAwMDAwWhcNMTEwMjExMjM1OTU5WjCBjTEhMB8GA1UE CxMYRG9tYWluIENvbnRyb2wgVmFsaWRhdGVkMSgwJgYDVQQLEx9Qcm92aWRlZCBi eSBHbG9iZSBIb3N0aW5nLCBJbmMuMSQwIgYDVQQLExtHbG9iZSBTdGFuZGFyZCBX aWxkY2FyZCBTU0wxGDAWBgNVBAMUDyoubGVlY2hwYWNrLmNvbTCCASIwDQYJKoZI hvcNAQEBBQADggEPADCCAQoCggEBAKX7jECMlYEtcvqVWQVUpXNxO/VaHELghqy/ Ml8dOfOXG29ZMZsKUMqS0jXEwd+Bdpm31lBxOALkj8o79hX0tspLMjgtCnreaker 49y62BcjfguXRFAaiseXTNbMer5lDWiHlf1E7uCoTTiczGqBNfl6qSJlpe4rYBtq XxBAiygaNba6Owghuh19+Uj8EICb2pxbJNFfNzU1D9InFdZSVqKHYBem4Cdrtxua W4+YONsfLnnfkRQ6LOLeYExHziTQhSavSv9XaCl9Zqzm5/eWbQqLGRpSJoEPY/0T GqnmeMIq5M35SWZgOVV10j3pOCS8o0zpp7hMJd2R/HwVaPCLjukCAwEAAaOCAcQw ggHAMB8GA1UdIwQYMBaAFB9UlnKtPUDnlln3STFTCWb5DWtyMB0GA1UdDgQWBBT0 8rPIMr7JDa2Xs5he5VXAvMWArjAOBgNVHQ8BAf8EBAMCBaAwDAYDVR0TAQH/BAIw ADAdBgNVHSUEFjAUBggrBgEFBQcDAQYIKwYBBQUHAwIwVQYDVR0gBE4wTDBKBgsr BgEEAbIxAQICGzA7MDkGCCsGAQUFBwIBFi1odHRwOi8vd3d3Lmdsb2Jlc3NsLmNv bS9kb2NzL0dsb2JlU1NMX0NQUy5wZGYwRgYDVR0fBD8wPTA7oDmgN4Y1aHR0cDov L2NybC5nbG9iZXNzbC5jb20vR0xPQkVTU0xEb21haW5WYWxpZGF0ZWRDQS5jcmww dwYIKwYBBQUHAQEEazBpMEEGCCsGAQUFBzAChjVodHRwOi8vY3J0Lmdsb2Jlc3Ns LmNvbS9HTE9CRVNTTERvbWFpblZhbGlkYXRlZENBLmNydDAkBggrBgEFBQcwAYYY aHR0cDovL29jc3AuZ2xvYmVzc2wuY29tMCkGA1UdEQQiMCCCDyoubGVlY2hwYWNr LmNvbYINbGVlY2hwYWNrLmNvbTANBgkqhkiG9w0BAQUFAAOCAQEAB2Y7vQsq065K s+/n6nJ8ZjOKbRSPEiSuFO+P7ovlfq9OLaWRHUtJX0sLntnWY1T9hVPvS5xz/Ffl w9B8g/EVvvfMyOw/5vIyvHq722fAAC1lWU1rV3ww0ng5bgvD20AgOlIaYBvRq8EI 5Dxo2og2T1UjDN44GOSWsw5jetvVQ+SPeNPQLWZJS9pNCzFQ/3QDWNPOvHqEeRcz WkOTCqbOSZYvoSPvZ3APh+1W6nqiyoku/FCv9otSCtXPKtyVa23hBQ+iuxqIM4/R gncnUKASi6KQrWMQiAI5UDCtq1c09uzjw+JaEzAznxEgqftTOmXAJSQGqZGd6HpD ZqTjb+WBJQ== -----END CERTIFICATE----- subject=/OU=Domain Control Validated/OU=Provided by Globe Hosting, Inc./OU=Globe Standard Wildcard SSL/CN=*.domain.com issuer=/C=RO/O=GLOBE HOSTING CERTIFICATION AUTHORITY/CN=GLOBE SSL Domain Validated CA --- No client certificate CA names sent --- SSL handshake has read 3313 bytes and written 343 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: 5F9C8DC277A372E28A4684BAE5B311533AD30E251369D144A13DECA3078E067F Session-ID-ctx: Master-Key: 9B531A75347E6E7D19D95365C1208F2ED37E4004AA8F71FC614A18937BEE2ED9F82D58925E0B3931492AD3D2AA6EFD3B Key-Arg : None Start Time: 1288618211 Timeout : 300 (sec) Verify return code: 21 (unable to verify the first certificate) ---

  Read the article

• pxe boot fails with message: no DEFAULT or UI configuration directive found

  - by spockaroo

  I am trying to pxe-boot a machine (client), and in the process I am trying to setup a tftp server that this machine can boot off. On the server, which runs Ubuntu 10.10, I have setup dhcp, dns, nfs, and tftp-hpa servers. All the servers/deamons start fine. I tested the tftp server by using a tftp client and downloading a file that the server directory hosts. My /etc/xinet.d/tftp looks like this service tftp { disable = no socket_type = dgram wait = yes user = nobody server = /usr/sbin/in.tftpd server_args = -v -s /var/lib/tftpboot only_from = 10.1.0.0/24 interface = 10.1.0.1 } My /etc/default/tftpd-hpa looks like this RUN_DAEMON="yes" OPTIONS="-l -s /var/lib/tftpboot" TFTP_USERNAME="tftp" TFTP_DIRECTORY="/var/lib/tftpboot" TFTP_ADDRESS="0.0.0.0:69" TFTP_OPTIONS="--secure" My /var/lib/tftpboot/ directory looks like this initrd.img-2.6.35-25-generic-pae vmlinuz-2.6.35-25-generic-pae pxelinux.0 pxelinux.cfg -- default I did sudo chmod 644 /var/lib/tftpboot/pxelinux.cfg/default chmod 755 /var/lib/tftpboot/initrd.img-2.6.35-25-generic-pae chmod 755 /var/lib/tftpboot/vmlinuz-2.6.35-25-generic-pae /var/lib/tftpboot/pxelinux.cfg has the following contents SERIAL 0 19200 0 LABEL linux KERNEL vmlinuz-2.6.35-25-generic-pae APPEND root=/dev/nfs initrd=initrd.img-2.6.35-25-generic-pae nfsroot=10.1.0.1:/nfsroot ip=dhcp console=ttyS0,19200n8 rw I copied /var/lib/tftpboot/pxelinux.0 from /usr/lib/syslinux/ after installing the package syslinux-common. Also just for completeness, /etc/dhcp3/dhcpd.conf the following lines (relevant to this interface) subnet 10.1.0.0 netmask 255.255.255.0 { range 10.1.0.100 10.1.0.240; option routers 10.1.0.1; option broadcast-address 10.1.0.255; option domain-name-servers 10.1.0.1; filename "pxelinux.0"; } When I boot the client machine, and watch the output over the serial port, I notice that the client requests an ip address from the server and gets it. Then I see TFTP being displayed - indicating that it is trying to connect to the TFTP server. This succeeds, and I see TFTP.|, which return immediately displaying the following message PXELINUX 4.01 debian-20100714 Copyright (C) 1994-2010 H. Peter Anvin et al No DEFAULT or UI configuration directive found! boot: /var/log/syslog shows Feb 20 15:24:05 ch in.tftpd[2821]: tftp: client does not accept options What option is it talking about in the syslog? I assume it is referring to OPTIONS or TFTP_OPTIONS, but what am I doing wrong?

  Read the article

• Debian keyring error: "No keyring installed"

  - by donatello

  I have a Debian Squeeze EC2 AMI. On booting up an instance with it and trying to install packages with apt-get I get errors saying there is no keyring installed. Here is the error with apt-get update: root@ip:~# apt-get update Get:1 http://ftp.us.debian.org squeeze Release.gpg [1672 B] Ign http://ftp.us.debian.org/debian/ squeeze/contrib Translation-en Ign http://ftp.us.debian.org/debian/ squeeze/main Translation-en Ign http://ftp.us.debian.org/debian/ squeeze/non-free Translation-en Get:2 http://security.debian.org squeeze/updates Release.gpg [836 B] Ign http://security.debian.org/ squeeze/updates/contrib Translation-en Ign http://security.debian.org/ squeeze/updates/main Translation-en Hit http://ftp.us.debian.org squeeze Release Ign http://ftp.us.debian.org squeeze Release Ign http://security.debian.org/ squeeze/updates/non-free Translation-en Ign http://ftp.us.debian.org squeeze/main Sources/DiffIndex Get:3 http://security.debian.org squeeze/updates Release [86.9 kB] Ign http://security.debian.org squeeze/updates Release Ign http://ftp.us.debian.org squeeze/contrib Sources/DiffIndex Ign http://ftp.us.debian.org squeeze/non-free Sources/DiffIndex Ign http://ftp.us.debian.org squeeze/main amd64 Packages/DiffIndex Ign http://ftp.us.debian.org squeeze/contrib amd64 Packages/DiffIndex Ign http://ftp.us.debian.org squeeze/non-free amd64 Packages/DiffIndex Ign http://security.debian.org squeeze/updates/main Sources/DiffIndex Hit http://ftp.us.debian.org squeeze/main Sources Hit http://ftp.us.debian.org squeeze/contrib Sources Hit http://ftp.us.debian.org squeeze/non-free Sources Hit http://ftp.us.debian.org squeeze/main amd64 Packages Hit http://ftp.us.debian.org squeeze/contrib amd64 Packages Ign http://security.debian.org squeeze/updates/contrib Sources/DiffIndex Ign http://security.debian.org squeeze/updates/non-free Sources/DiffIndex Ign http://security.debian.org squeeze/updates/main amd64 Packages/DiffIndex Ign http://security.debian.org squeeze/updates/contrib amd64 Packages/DiffIndex Ign http://security.debian.org squeeze/updates/non-free amd64 Packages/DiffIndex Hit http://ftp.us.debian.org squeeze/non-free amd64 Packages Get:4 http://backports.debian.org squeeze-backports Release.gpg [836 B] Ign http://backports.debian.org/debian-backports/ squeeze-backports/main Translation-en Hit http://security.debian.org squeeze/updates/main Sources Hit http://security.debian.org squeeze/updates/contrib Sources Hit http://security.debian.org squeeze/updates/non-free Sources Hit http://security.debian.org squeeze/updates/main amd64 Packages Hit http://security.debian.org squeeze/updates/contrib amd64 Packages Hit http://security.debian.org squeeze/updates/non-free amd64 Packages Get:5 http://backports.debian.org squeeze-backports Release [77.6 kB] Ign http://backports.debian.org squeeze-backports Release Hit http://backports.debian.org squeeze-backports/main amd64 Packages/DiffIndex Hit http://backports.debian.org squeeze-backports/main amd64 Packages Fetched 3346 B in 0s (5298 B/s) Reading package lists... Done W: GPG error: http://ftp.us.debian.org squeeze Release: No keyring installed in /etc/apt/trusted.gpg.d/. W: GPG error: http://security.debian.org squeeze/updates Release: No keyring installed in /etc/apt/trusted.gpg.d/. W: GPG error: http://backports.debian.org squeeze-backports Release: No keyring installed in /etc/apt/trusted.gpg.d/. Googling around didn't really help me fix this problem. I tried installing the packages "debian-keyring" and "debian-archive-keyring" but the error does not go away. I'd like to avoid installing unstrusted packages. Any help is appreciated! Why does this error happen and where can I learn more?

  Read the article

• Cannot install virtualbox-ose-guest-dkms on Ubuntu 10.04

  - by mrduongnv

  I'm using Ubuntu 10.04 and kernel: 2.6.38-11-generic-pae. While using VirtualBox, i got this error: Kernel driver not installed (rc=-1908) Please install the virtualbox-ose-dkms package and execute 'modprobe vboxdrv' as root. I tried to execute the command: sudo modprobe vboxdrv and got this error: FATAL: Module vboxdrv not found. After that, i execute this: sudo aptitude install virtualbox-ose-guest-dkms duongnv@duongnv-laptop:~$ sudo aptitude install virtualbox-ose-guest-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done The following partially installed packages will be configured: virtualbox-ose-guest-dkms 0 packages upgraded, 0 newly installed, 0 to remove and 105 not upgraded. Need to get 0B of archives. After unpacking 0B will be used. Writing extended state information... Done Setting up virtualbox-ose-guest-dkms (3.1.6-dfsg-2ubuntu2) ... Removing old virtualbox-ose-guest-3.1.6 DKMS files... ------------------------------ Deleting module version: 3.1.6 completely from the DKMS tree. ------------------------------ Done. Loading new virtualbox-ose-guest-3.1.6 DKMS files... First Installation: checking all kernels... Building only for 2.6.38-11-generic-pae Building for architecture i686 Building initial module for 2.6.38-11-generic-pae Error! Bad return status for module build on kernel: 2.6.38-11-generic-pae (i686) Consult the make.log in the build directory /var/lib/dkms/virtualbox-ose-guest/3.1.6/build/ for more information. dpkg: error processing virtualbox-ose-guest-dkms (--configure): subprocess installed post-installation script returned error exit status 10 Errors were encountered while processing: virtualbox-ose-guest-dkms E: Sub-process /usr/bin/dpkg returned an error code (1) A package failed to install. Trying to recover: Setting up virtualbox-ose-guest-dkms (3.1.6-dfsg-2ubuntu2) ... Removing old virtualbox-ose-guest-3.1.6 DKMS files... ------------------------------ Deleting module version: 3.1.6 completely from the DKMS tree. ------------------------------ Done. Loading new virtualbox-ose-guest-3.1.6 DKMS files... First Installation: checking all kernels... Building only for 2.6.38-11-generic-pae Building for architecture i686 Building initial module for 2.6.38-11-generic-pae Error! Bad return status for module build on kernel: 2.6.38-11-generic-pae (i686) Consult the make.log in the build directory /var/lib/dkms/virtualbox-ose-guest/3.1.6/build/ for more information. dpkg: error processing virtualbox-ose-guest-dkms (--configure): subprocess installed post-installation script returned error exit status 10 Errors were encountered while processing: virtualbox-ose-guest-dkms Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done

  Read the article

• Gnome Install Error (1) [closed]

  - by Guy1984

  I'm trying to install Gnome on my Ubuntu 12.04 P.Pangolin and getting the following errors: root@***:~# sudo apt-get install gnome-core gnome-session-fallback Reading package lists... Done Building dependency tree Reading state information... Done gnome-core is already the newest version. gnome-session-fallback is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 4 not upgraded. 5 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up bluez (4.98-2ubuntu7) ... start: Job failed to start invoke-rc.d: initscript bluetooth, action "start" failed. dpkg: error processing bluez (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of gnome-bluetooth: gnome-bluetooth depends on bluez (>= 4.36); however: Package bluez is not configured yet. dpkg: error processing gnome-bluetooth (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-shell: gnome-shell depends on gnome-bluetooth (>= 3.0.0); however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-shell (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-user-share: gnome-user-share depends on gnome-bluetooth; however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-user-share (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-core: gnome-core depends on gNo apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already nome-bluetooth (>= 3.0); however: Package gnome-bluetooth is not configured yet. gnome-core depends on gnome-shell (>= 3.0); however: Package gnome-shell is not configured yet. gnome-core depends on gnome-user-share (>= 3.0); however: Package gnome-user-share is not configured yet. dpkg: error processing gnome-core (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: bluez gnome-bluetooth gnome-shell gnome-user-share gnome-core E: Sub-process /usr/bin/dpkg returned an error code (1) Any thoughts?

  Read the article

• Gnome Install Error (1) [closed]

  - by Guy1984

  I'm trying to install Gnome on my Ubuntu 12.04 P.Pangolin and getting the following errors: root@***:~# sudo apt-get install gnome-core gnome-session-fallback Reading package lists... Done Building dependency tree Reading state information... Done gnome-core is already the newest version. gnome-session-fallback is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 4 not upgraded. 5 not fully installed or removed. After this operation, 0 B of additional disk space will be used. Do you want to continue [Y/n]? y Setting up bluez (4.98-2ubuntu7) ... start: Job failed to start invoke-rc.d: initscript bluetooth, action "start" failed. dpkg: error processing bluez (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of gnome-bluetooth: gnome-bluetooth depends on bluez (>= 4.36); however: Package bluez is not configured yet. dpkg: error processing gnome-bluetooth (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-shell: gnome-shell depends on gnome-bluetooth (>= 3.0.0); however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-shell (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-user-share: gnome-user-share depends on gnome-bluetooth; however: Package gnome-bluetooth is not configured yet. dpkg: error processing gnome-user-share (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of gnome-core: gnome-core depends on gNo apport report written because the error message indicates its a followup error from a previous failure. No apport report written because the error message indicates its a followup error from a previous failure. No apport report written because MaxReports is reached already No apport report written because MaxReports is reached already nome-bluetooth (>= 3.0); however: Package gnome-bluetooth is not configured yet. gnome-core depends on gnome-shell (>= 3.0); however: Package gnome-shell is not configured yet. gnome-core depends on gnome-user-share (>= 3.0); however: Package gnome-user-share is not configured yet. dpkg: error processing gnome-core (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: bluez gnome-bluetooth gnome-shell gnome-user-share gnome-core E: Sub-process /usr/bin/dpkg returned an error code (1) Any thoughts?

  Read the article

• BIND9 / DNS Zone / Dedicated Server / Unique Reverse DNS

  - by user2832131

  I locate a dedicated server in a datacenter with no DNS Zone setup. Datacenter panel have 1 textfield only you can fill one Reverse DNS only. According with datacenter instructions here... [instructions]: http://www.wiki.hetzner.de/index.php/DNS-Reverse-DNS/en#How_can_I_assign_several_names_to_my_IP_address.2C_if_different_domains_are_hosted_on_my_server.3F How_can_I_assign_several_names_to_my_IP_address ...I need to install BIND9 in order to configure other records like CNAME and MX. Ok, I've installed BIND9, created a Master Zone. And following this example, I put it in the Zone File: [example]: http://wiki.hetzner.de/index.php/DNS_Zonendatei/en example $ttl 86400 @ IN SOA ns1.first-ns.de. postmaster.robot.first-ns.de. ( 1383411730 14400 1800 604800 86400 ) @ IN NS ns1.first-ns.de. @ IN NS robotns2.second-ns.de. @ IN NS robotns3.second-ns.com. localhost IN A 127.0.0.1 @ IN A 144.86.786.651 www IN A 144.86.786.651 loopback IN CNAME localhost But when I point my domain to ns1.first-ns.de, DNS Register says "time out". Am I missing something? I created a Master zone. Should it be a Slave zone? named.conf: include "/etc/bind/named.conf.options"; include "/etc/bind/named.conf.local"; include "/etc/bind/named.conf.default-zones"; named.conf.options: options { directory "/var/cache/bind"; dnssec-validation auto; auth-nxdomain no; # conform to RFC1035 listen-on-v6 { any; }; }; named.conf.local: zone "mydomain.com" { type master; file "/var/lib/bind/mydomain.com.hosts"; allow-update {any;}; allow-transfer {any;}; allow-query {any;}; }; named.conf.default-zones: zone "." { type hint; file "/etc/bind/db.root"; }; zone "localhost" { type master; file "/etc/bind/db.local"; }; zone "127.in-addr.arpa" { type master; file "/etc/bind/db.127"; }; zone "0.in-addr.arpa" { type master; file "/etc/bind/db.0"; }; zone "255.in-addr.arpa" { type master; file "/etc/bind/db.255"; }; Problem is that I'm moving my site, and can't update the new NS server due to a 'timeout' message when filling new datacenter NS. I'm filling: MASTER: ns1.first-ns.de SLAVE1: robotns2.second-ns.de SLAVE2: robotns3.second-ns.com

  Read the article

• Migrate from MySQL to PostgreSQL on Linux (Kubuntu)

  - by Dave Jarvis

  Storyline Trying to migrate a database from MySQL to PostgreSQL. All the documentation I have read covers, in great detail, how to migrate the structure. I have found very little documentation on migrating the data. The schema has 13 tables (which have been migrated successfully) and 9 GB of data. MySQL version: 5.1.x PostgreSQL version: 8.4.x I want to use the R programming language to analyze the data using SQL select statements; PostgreSQL has PL/R, but MySQL has nothing (as far as I can tell). A long time ago in a galaxy far, far away... Create the database location (/var has insufficient space; also dislike having the PostgreSQL version number everywhere -- upgrading would break scripts!): sudo mkdir -p /home/postgres/main sudo cp -Rp /var/lib/postgresql/8.4/main /home/postgres sudo chown -R postgres.postgres /home/postgres sudo chmod -R 700 /home/postgres sudo usermod -d /home/postgres/ postgres All good to here. Next, restart the server and configure the database using these installation instructions: sudo apt-get install postgresql pgadmin3 sudo /etc/init.d/postgresql-8.4 stop sudo vi /etc/postgresql/8.4/main/postgresql.conf Change data_directory to /home/postgres/main sudo /etc/init.d/postgresql-8.4 start sudo -u postgres psql postgres \password postgres sudo -u postgres createdb climate pgadmin3 Use pgadmin3 to configure the database and create a schema. A New Hope The episode began in a remote shell known as bash, with both databases running, and the installation of a command with a most unusual logo: SQL Fairy. perl Makefile.PL sudo make install sudo apt-get install perl-doc (strangely, it is not called perldoc) perldoc SQL::Translator::Manual Extract a PostgreSQL-friendly DDL and all the MySQL data: sqlt -f DBI --dsn dbi:mysql:climate --db-user user --db-password password -t PostgreSQL > climate-pg-ddl.sql mysqldump --skip-add-locks --complete-insert --no-create-db --no-create-info --quick --result-file="climate-my.sql" --databases climate --skip-comments -u root -p The Database Strikes Back Recreate the structure in PostgreSQL as follows: pgadmin3 (switch to it) Click the Execute arbitrary SQL queries icon Open climate-pg-ddl.sql Search for TABLE " replace with TABLE climate." (insert the schema name climate) Search for on " replace with on climate." (insert the schema name climate) Press F5 to execute This results in: Query returned successfully with no result in 122 ms. Replies of the Jedi At this point I am stumped. Where do I go from here (what are the steps) to convert climate-my.sql to climate-pg.sql so that they can be executed against PostgreSQL? How to I make sure the indexes are copied over correctly (to maintain referential integrity; I don't have constraints at the moment to ease the transition)? How do I ensure that adding new rows in PostgreSQL will start enumerating from the index of the last row inserted (and not conflict with an existing primary key from the sequence)? Resources A fair bit of information was needed to get this far: https://help.ubuntu.com/community/PostgreSQL http://articles.sitepoint.com/article/site-mysql-postgresql-1 http://wiki.postgresql.org/wiki/Converting_from_other_Databases_to_PostgreSQL#MySQL http://pgfoundry.org/frs/shownotes.php?release_id=810 http://sqlfairy.sourceforge.net/ Thank you!

  Read the article

• Install MegaCli to Monitor Perc 5/i in Nexentastor 3

  - by Peter Valadez

  I have a Dell 2950 with a Perc 5/i Raid controller that we've already installed Nexentastor 3 Community Edition on. We setup a raid-10 array that and put a ZFS pool on top of the hardware. As I understand, in this configuration ZFS/Nexentastor will not be able to tell when a disk fails in the array. Obviously, this is not optimal. Since the Dell Perc 5/i controller is a rebranded LSI controller, you should be able to use the MegaCli utility to manage the array and monitor its condition. I had seen in a separate forum that the Perc 5/i is very similar to the LSI MegaRAID 8480E, so I tried installing the MegaCli utility at the link below. However, I have not been able to successfully install the utility. http://www.lsi.com/support/products/Pages/MegaRAIDSAS8480E.aspx Here is what happened when I tried to install MegaCli: root@Nexenta2:/files# pkgadd -d MegaCli.pkg Warning: unable to relocate '$BASEDIR' mv: cannot move `solmegacli-8.02.16/' to a subdirectory of itself, `solmegacli-8.02.16//var/lib/dpkg/alien/solmegacli/reloc/solmegacli-8.02.16' mv: cannot move `solmegacli-8.02.16/' to a subdirectory of itself, `solmegacli-8.02.16//opt/solmegacli-8.02.16' 822-date: warning: This program is deprecated. Please use 'date -R' instead. 822-date: warning: This program is deprecated. Please use 'date -R' instead. solmegacli_8.02.16-1_all.deb generated (Reading database ... 41397 files and directories currently installed.) Preparing to replace solmegacli 8.02.16-1 (using solmegacli_8.02.16-1_all.deb) ... Unpacking replacement solmegacli ... Setting up solmegacli (8.02.16-1) ... In /var/logs/dpkg.log: 2012-03-23 20:40:19 status unpacked solmegacli 8.02.16-1 2012-03-23 20:40:19 configure solmegacli 8.02.16-1 8.02.16-1 2012-03-23 20:40:19 status unpacked solmegacli 8.02.16-1 2012-03-23 20:40:19 status half-configured solmegacli 8.02.16-1 2012-03-23 20:40:19 status installed solmegacli 8.02.16-1 So... I've got three questions: Is it possible to install and use MegaCli in Nexentastor 3? If so, how can I install MegaCli on Nexentastor 3? Suggestions welcome!!! If not, is there a better way to monitor the condition of the Perc 5/i hardware raid? Our 2950 does have a DRAC card, so can I use that to monitor the raid condition?

  Read the article

• VPN iptables Forwarding: Net-to-net

  - by Mike Holler

  I've tried to look elsewhere on this site but I couldn't find anything matching this problem. Right now I have an ipsec tunnel open between our local network and a remote network. Currently, the local box running Openswan ipsec with the tunnel open can ping the remote ipsec box and any of the other computers in the remote network. When logged into on of the remote computers, I can ping any box in our local network. That's what works, this is what doesn't: I can't ping any of the remote computers via a local machine that is not the ipsec box. Here's a diagram of our network: [local ipsec box] ----------\ \ [arbitrary local computer] --[local gateway/router] -- [internet] -- [remote ipsec box] -- [arbitrary remote computer] The local ipsec box and the arbitrary local computer have no direct contact, instead they communicate through the gateway/router. The router has been set up to forward requests from local computers for the remote subnet to the ipsec box. This works. The problem is the ipsec box doesn't forward anything. Whenever an arbitrary local computer pings something on the remote subnet, this is the response: [user@localhost ~]# ping 172.16.53.12 PING 172.16.53.12 (172.16.53.12) 56(84) bytes of data. From 10.31.14.16 icmp_seq=1 Destination Host Prohibited From 10.31.14.16 icmp_seq=2 Destination Host Prohibited From 10.31.14.16 icmp_seq=3 Destination Host Prohibited Here's the traceroute: [root@localhost ~]# traceroute 172.16.53.12 traceroute to 172.16.53.12 (172.16.53.12), 30 hops max, 60 byte packets 1 router.address.net (10.31.14.1) 0.374 ms 0.566 ms 0.651 ms 2 10.31.14.16 (10.31.14.16) 2.068 ms 2.081 ms 2.100 ms 3 10.31.14.16 (10.31.14.16) 2.132 ms !X 2.272 ms !X 2.312 ms !X That's the IP for our ipsec box it's reaching, but it's not being forwarded. On the IPSec box I have enabled IP Forwarding in /etc/sysctl.conf net.ipv4.ip_forward = 1 And I have tried to set up IPTables to forward: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [759:71213] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 25 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 500 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 4500 -j ACCEPT -A INPUT -m policy --dir in --pol ipsec -j ACCEPT -A INPUT -p esp -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -s 10.31.14.0/24 -d 172.16.53.0/24 -j ACCEPT -A FORWARD -m policy --dir in --pol ipsec -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT Am I missing a rule in IPTables? Is there something I forgot? NOTE: All the machines are running CentOS 6.x Edit: Note 2: eth1 is the only network interface on the local ipsec box.

  Read the article

• Xen won't start after it had been working

  - by Paul Tomblin

  I've been setting up this Debian Stable system with a dom0 and 3 domUs. It was working fine for several days, and I'm almost ready to deploy it to the rack. But last night I shut it down with all three domUs still running for the first time, and today when I started it up, xend won't start. In /var/log/messages, I have: Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: blktapctrl: v1.0.0 Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [raw image (aio)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [raw image (sync)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [vmware image (vmdk)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [ramdisk image (ram)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Found driver: [qcow disk (qcow)] Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: couldn't find device number for 'blktap0' Apr 18 13:01:33 xen-test BLKTAPCTRL[4248]: Unable to start blktapctrl and in /var/log/xen/xend.log, I have this: [2010-04-18 12:46:32 3523] INFO (SrvDaemon:219) Xend exited with status 1. [2010-04-18 13:01:34 4255] INFO (SrvDaemon:331) Xend Daemon started [2010-04-18 13:01:34 4255] INFO (SrvDaemon:335) Xend changeset: unavailable. [2010-04-18 13:01:34 4255] INFO (SrvDaemon:342) Xend version: Unknown. [2010-04-18 13:01:34 4255] ERROR (SrvDaemon:353) Exception starting xend (no element found: line 1, column 0) Traceback (most recent call last): File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvDaemon.py", line 345, in run servers = SrvServer.create() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvServer.py", line 251, in create root.putChild('xend', SrvRoot()) File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvRoot.py", line 40, in __init__ self.get(name) File "/usr/lib/xen-3.2-1/lib/python/xen/web/SrvDir.py", line 82, in get val = val.getobj() File "/usr/lib/xen-3.2-1/lib/python/xen/web/SrvDir.py", line 52, in getobj File "/usr/lib/xen-3.2-1/lib/python/xen/xend/server/SrvNode.py", line 30, in _ _init__ self.xn = XendNode.instance() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendNode.py", line 709, in instance inst = XendNode() File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendNode.py", line 164, in __init__ saved_pifs = self.state_store.load_state('pif') File "/usr/lib/xen-3.2-1/lib/python/xen/xend/XendStateStore.py", line 104, in load_state dom = minidom.parse(xml_path) File "/usr/lib/python2.5/xml/dom/minidom.py", line 1915, in parse return expatbuilder.parse(file) File "/usr/lib/python2.5/xml/dom/expatbuilder.py", line 924, in parse result = builder.parseFile(fp) File "/usr/lib/python2.5/xml/dom/expatbuilder.py", line 211, in parseFile parser.Parse("", True) ExpatError: no element found: line 1, column 0 [2010-04-18 13:01:34 4253] INFO (SrvDaemon:219) Xend exited with status 1. Any clues as to what might be going wrong?

  Read the article

• Ubuntu suddenly freezes

  - by tapan

  I've a strange problem with my ubuntu 10.04 installation. Whenever i boot into ubuntu the entire system freezes / hangs soon after (~ 2 mins in). This problem exists on my windows 7 installation too. However if i start World of Warcraft or Warcraft on windows it doesnt hang for the duration i'm playing the game. After i stop playing and exit the game my laptop hangs inside 2 mins. Here is when it gets weirder. If i disconnect the charger, the laptop doesn't hang. However when I start it in ubuntu recovery mode and drop to root shell and use the 'startx' command everything works perfectly. I cannot figure out what the problem is. i have an intel core2duo 2.2ghz processor, intel mobile 965 graphics, 2 GB RAM for more details here is the output of cat /proc/cpuinfo : processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4389.80 clflush size : 64 power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4388.96 clflush size : 64 power management: here is the output of cat /proc/meminfo MemTotal: 2052440 kB MemFree: 55924 kB Buffers: 579352 kB Cached: 821752 kB SwapCached: 704 kB Active: 897124 kB Inactive: 1032256 kB Active(anon): 412140 kB Inactive(anon): 264804 kB Active(file): 484984 kB Inactive(file): 767452 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 1178440 kB HighFree: 6012 kB LowTotal: 874000 kB LowFree: 49912 kB SwapTotal: 995988 kB SwapFree: 986616 kB Dirty: 8928 kB Writeback: 0 kB AnonPages: 527596 kB Mapped: 76536 kB Slab: 39480 kB SReclaimable: 21100 kB SUnreclaim: 18380 kB PageTables: 5672 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2022208 kB Committed_AS: 1856400 kB VmallocTotal: 122880 kB VmallocUsed: 11928 kB VmallocChunk: 104644 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 892928 kB Also the kern.log doesn't show any errors. What I want to know is what might be the problem, how i could test for it and if there are any solutions I could try. Thanks :).

  Read the article

• using own mail server with external domain and dns. Now have internal dns. dkim test not working

  - by mojotaker

  I am not very knowledgeable in this area, but have been able to make great head way. Now i am stuck I setup my own mail server, e.g mailbox.example.com. I had the domain dns point to my mail server in my office. i was able to set up everything working fine. such as dkim and spf records. Recently i decided to setup an internal dns server in the office so as to resolve some addresses for some development servers internally. Ok the problem now is my mail server is sitting on the internal dns server (the mail server is on the same box as the dns server) its still able to send and receive emails but not sure if dkim is working properly. when i try to do a dkim test "amavisd test keys" i get "invalid (public key: not available)" and i know that that means i have a dns issue. so what should i do? I am currently looking at my internal dns zonefile and i dont know what to do (i am using bind dns server on an ubuntu-server box). do i configure a dkim txt record on the local dns ? or is there a way to forward dkim "request" to the external dns ? or do i have this whole thing done wrong ? To be clear Basically my internal domain name is the same as my external domain name (i.e example.com) i have a mail server within my internal domain mailbox.example.com, that uses my external domain dns (external dns has been setup to point to my emailserver (which of course is now sitting behind my internal dns)) dkim (i dont think its working because it fails the dkim test") Need help in determing the proper setup What is the proper way to set this up ? thank you Update: Here is my local dns zone file ; ; BIND data file for local loopback interface ; $TTL 604800 @ IN SOA webserver.example.com. root.example.com. ( //dns and webserver on the same box 2012030809 ; Serial 604800 ; Refresh 86400 ; Retry 2419200 ; Expire 604800 ) ; Negative Cache TTL ; @ IN NS webserver.example.com. @ IN A 192.168.1.117 @ IN AAAA ::1 ns IN A 192.168.1.117 www IN A xx.xx.xx.xxx // ip of external domain box (bluehost) work around to let local clients access website newsletter IN A xx.xx.xxx.117 // external ip address of local network mailbox.example.com. IN A 192.168.1.111 // internal ip of mailbox (mailserver webserver.example.com. IN A 192.168.1.117 //internal ip of a webserver

  Read the article

• How to find other end of unix socket connection?

  - by depesz

  I have a process (dbus-daemon) which has many open connection over UNIX sockets. One of these connections is fd #36: =$ ps uw -p 23284 USER PID %CPU %MEM VSZ RSS TTY STAT START TIME COMMAND depesz 23284 0.0 0.0 24680 1772 ? Ss 15:25 0:00 /bin/dbus-daemon --fork --print-pid 5 --print-address 7 --session =$ ls -l /proc/23284/fd/36 lrwx------ 1 depesz depesz 64 2011-03-28 15:32 /proc/23284/fd/36 -> socket:[1013410] =$ netstat -nxp | grep 1013410 (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) unix 3 [ ] STREAM CONNECTED 1013410 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD =$ netstat -nxp | grep dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1013953 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1013825 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1013726 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1013471 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1013410 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1012325 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1012302 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1012289 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1012151 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011957 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011937 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011900 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011775 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011771 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011769 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011766 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011663 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011635 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011627 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011540 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011480 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011349 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011312 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011284 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011250 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011231 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011155 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011061 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011049 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011035 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1011013 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1010961 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD unix 3 [ ] STREAM CONNECTED 1010945 23284/dbus-daemon @/tmp/dbus-3XDU4PYEzD Based on number connections, I assume that dbus-daemon is actually server. Which is OK. But how can I find which process is connected to it - using the connection that is 36th file handle in dbus-launcher? Tried lsof and even greps on /proc/net/unix but I can't figure out a way to find the client process.

  Read the article

• Mac OS X behind OpenLDAP and Samba

  - by Sam Hammamy

  I have been battling for a week now to get my Mac (Mountain Lion) to authenticate on my home network's OpenLDAP and Samba. From several sources, like the Ubuntu community docs, and other blogs, and after a hell of a lot of trial and error and piecing things together, I have created a samba.ldif that will pass the smbldap-populate when combined with apple.ldif and I have a fully functional OpenLDAP server and a Samba PDC that uses LDAP to authenticate the OS X Machine. The problem is that when I login, the home directory is not created or pulled from the server. I get the following in system.log Sep 21 06:09:15 Sams-MacBook-Pro.local SecurityAgent[265]: User info context values set for sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got ruser: (null) Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Got service: authorization Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): no authauth availale for user. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_principal_for_user(): failed: 7 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Failed to determine Kerberos principal name. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Done cleanup3 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): Kerberos 5 refuses you Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_authenticate(): pam_sm_authenticate: ntlm Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_acct_mgmt(): OpenDirectory - Membership cache TTL set to 1800. Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in od_record_check_pwpolicy(): retval: 0 Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Establishing credentials Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Got user: sam Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): Context initialised Sep 21 06:09:15 Sams-MacBook-Pro.local authorizationhost[270]: in pam_sm_setcred(): pam_sm_setcred: ntlm user sam doesn't have auth authority All that's great and good and I authenticate. Then I get CFPreferences: user home directory for user kCFPreferencesCurrentUser at /Network/Servers/172.17.148.186/home/sam is unavailable. User domains will be volatile. Failed looking up user domain root; url='file://localhost/Network/Servers/172.17.148.186/home/sam/' path=/Network/Servers/172.17.148.186/home/sam/ err=-43 uid=9000 euid=9000 If you're wondering where /Network/Servers/IP/home/sam comes from, it's from a couple of blogs that said the OpenLDAP attribute apple-user-homeDirectory should have that value and the NFSHomeDirectory on the mac should point to apple-user-homeDirectory I also set the attr apple-user-homeurl to <home_dir><url>smb://172.17.148.186/sam/</url><path></path></home_dir> which I found on this forum. Any help is appreciated, because I'm banging my head against the wall at this point. By the way, I intend to create a blog on my vps just for this, and create an install script in python that people can download so no one has to go through what I've had to go through this week :) After some sleep I am going to try to login from a windows machine and report back here. Thanks Sam

  Read the article

• Ubuntu/Windows suddenly freezes

  - by tapan

  I've a strange problem with my ubuntu 10.04 installation. Whenever i boot into ubuntu the entire system freezes / hangs soon after (~ 2 mins in). This problem exists on my windows 7 installation too. However if i start World of Warcraft or Warcraft on windows it doesnt hang for the duration i'm playing the game. After i stop playing and exit the game my laptop hangs inside 2 mins. Here is when it gets weirder. If i disconnect the charger, the laptop doesn't hang. However when I start it in ubuntu recovery mode and drop to root shell and use the 'startx' command everything works perfectly. I cannot figure out what the problem is. i have an intel core2duo 2.2ghz processor, intel mobile 965 graphics, 2 GB RAM for more details here is the output of cat /proc/cpuinfo : processor : 0 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4389.80 clflush size : 64 power management: processor : 1 vendor_id : GenuineIntel cpu family : 6 model : 15 model name : Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz stepping : 11 cpu MHz : 2201.000 cache size : 4096 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fdiv_bug : no hlt_bug : no f00f_bug : no coma_bug : no fpu : yes fpu_exception : yes cpuid level : 10 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe nx lm constant_tsc arch_perfmon pebs bts pni dtes64 monitor ds_cpl vmx est tm2 ssse3 cx16 xtpr pdcm lahf_lm ida tpr_shadow vnmi flexpriority bogomips : 4388.96 clflush size : 64 power management: here is the output of cat /proc/meminfo MemTotal: 2052440 kB MemFree: 55924 kB Buffers: 579352 kB Cached: 821752 kB SwapCached: 704 kB Active: 897124 kB Inactive: 1032256 kB Active(anon): 412140 kB Inactive(anon): 264804 kB Active(file): 484984 kB Inactive(file): 767452 kB Unevictable: 0 kB Mlocked: 0 kB HighTotal: 1178440 kB HighFree: 6012 kB LowTotal: 874000 kB LowFree: 49912 kB SwapTotal: 995988 kB SwapFree: 986616 kB Dirty: 8928 kB Writeback: 0 kB AnonPages: 527596 kB Mapped: 76536 kB Slab: 39480 kB SReclaimable: 21100 kB SUnreclaim: 18380 kB PageTables: 5672 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 2022208 kB Committed_AS: 1856400 kB VmallocTotal: 122880 kB VmallocUsed: 11928 kB VmallocChunk: 104644 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 892928 kB Also the kern.log doesn't show any errors. What I want to know is what might be the problem, how i could test for it and if there are any solutions I could try. Thanks :).

  Read the article

• Mono through FastCGI on nginx

  - by Stijn

  I'm going through http://www.mono-project.com/FastCGI_Nginx and can't get it to work. The FastCGI server seems to be running. The following is from the error log: upstream sent unexpected FastCGI record: 3 while reading response header from upstream, client: 192.168.1.125, server: arch, request: "GET /Default.aspx HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "arch" Command used to start the server (I've tried server2 and server4, using a simple .NET 2.0 or .NET 4.0 project): fastcgi-mono-server2 /applications=arch:/:/var/www/test/public/ /socket=tcp:127.0.0.1:9000 /stopable=True nginx config: server { listen 80; server_name arch; access_log /var/www/test/log/access.log; error_log /var/www/test/log/error.log; location / { root /var/www/test/public; index index.html index.htm default.aspx Default.aspx; fastcgi_index Default.aspx; fastcgi_pass 127.0.0.1:9000; fastcgi_param PATH_INFO ""; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } Using xsp4 works fine, I can browse the site. I've enabled FastCGI logging, this is the output: [2012-04-15 23:51:18Z] Debug Accepting an incoming connection. [2012-04-15 23:51:18Z] Notice Beginning to receive records on connection. [2012-04-15 23:51:18Z] Debug Record received. (Type: BeginRequest, ID: 1, Length: 8) [2012-04-15 23:51:18Z] Debug Record received. (Type: Params, ID: 1, Length: 386) [2012-04-15 23:51:18Z] Debug Record received. (Type: Params, ID: 1, Length: 0) [2012-04-15 23:51:18Z] Debug Read parameter. (PATH_INFO = ) [2012-04-15 23:51:18Z] Debug Read parameter. (SCRIPT_FILENAME = /var/www/test/public/Home) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_HOST = arch) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_USER_AGENT = Mozilla/5.0 (Windows NT 6.1; WOW64; rv:11.0) Gecko/20100101 Firefox/11.0) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_ACCEPT = text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_ACCEPT_LANGUAGE = en-gb,en;q=0.5) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_ACCEPT_ENCODING = gzip, deflate) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_CONNECTION = keep-alive) [2012-04-15 23:51:18Z] Debug Read parameter. (HTTP_COOKIE = ASP.NET_SessionId=2C3D702C9B0F23F69B80820B) [2012-04-15 23:51:18Z] Error Failed to process connection. Reason: Argument cannot be null. Parameter name: s [2012-04-15 23:51:18Z] Debug Record sent. (Type: EndRequest, ID: 1, Length: 8) [2012-04-15 23:51:18Z] Debug The FastCGI connection has been closed.

  Read the article

• How to tell if a freebsd jail is up to date?

  - by Martin Torhage

  I've set up a "Service Jail" in FreeBSD 8.0 according to the FreeBSD Handbook (http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/jails-application.html). After upgrading the host to the latest patch level and then performed a jail-upgrade, freebsd-fetch still reports that there are files in need of an update in the jail. Is this expected? Then how do I know if a jail is up to date? This is what I've done in more detail: After the initial setup of the jail freebsd-update fetch reported that there were no updates available neither in the host system nor in the jail. This was expected. A while later freebsd-update fetch reported that the following files where in need of an update both in the host and in the jail. /usr/lib/libssl.a /usr/lib/libssl_p.a /usr/lib/libzpool.a /usr/lib32/libssl.a /usr/lib32/libssl_p.a /usr/lib32/libzpool.a I updated the host and followed the upgrade guide for the jail (http://www.freebsd.org/doc/en_US.ISO8859-1/books/handbook/jails-application.html#JAILS-SERVICE-JAILS-UPGRADING). freebsd-update fetch now reports that there are no updates available in the host but the following is the output from freebsd-update fetch in the jail: [root@bb /]# freebsd-update fetch Looking up update.FreeBSD.org mirrors... 3 mirrors found. Fetching metadata signature for 8.0-RELEASE from update5.FreeBSD.org... done. Fetching metadata index... done. Inspecting system... done. Preparing to download files... done. The following files are affected by updates, but no changes have been downloaded because the files have been modified locally: /var/db/mergemaster.mtree The following files will be updated as part of updating to 8.0-RELEASE-p2: /usr/lib/libssl.a /usr/lib/libssl_p.a /usr/lib/libzpool.a /usr/lib32/libssl.a /usr/lib32/libssl_p.a /usr/lib32/libzpool.a Shouldn't freebsd-update know that the jail is up to date or have I failed upgrading it? How am I supposed to know if a jail is up to date if freebsd-update can't tell? I'm sure I ran make cleandir twice before make buildworld. TIA

  Read the article

• 5.5.0 smtp;554 transaction failed spam message not queued

  - by Miguel

  Some users are trying to send email to certain domains using Exchange Server 2003, but the message is always is rejected and the following message is shown: 5.5.0 smtp;554 Transaction Failed Spam Message not queued The IP is not in a black list (checked using http://whatismyipaddress.com/blacklist-check and is clean - not listed). The emails were checked using using smtpdiag ("a troubleshooting tool designed to work directly on a Windows server with IIS/SMTP service enabled or with Exchange Server installed") and the connection using port 25 is ok. Also, an nslookup with set type=ptr shows (names and IP changed, "" means I typed something): C:\Documents and Settings\administrator>nslookup Default Server: publicdns.isp.net Address: 10.10.10.10 > server publicdns.isp.net Default Server: publicdns.isp.net Address: 10.10.10.10 > set type=ptr >mydomain.com Server: publicdns.isp.net Address: 10.10.10.10 mydomain.com primary name server = publicdns.isp.net responsible mail addr = root.isp.net serial = 2011061301 refresh = 10800 (3 hours) retry = 3600 (1 hour) expire = 604800 (7 days) default TTL = 86400 (1 day) > 20.21.22.23 Server: publicdns.isp.net Address: 10.10.10.10 23.22.21.20.in-addr.arpa name = mail.mydomain.com 20.21.in-addr.arpa nameserver = publicdns.isp.net 20.21.in-addr.arpa nameserver = publicdns2.isp.net publicdns2.isp.net internet address = 10.10.10.11 publicdns.isp.net internet address = 10.10.10.10 Server: publicdns.isp.net Address: 10.10.10.10 23.22.21.20.in-addr.arpa name = mail.mydomain.com 20.21.in-addr.arpa nameserver = publicdns.isp.net 20.21.in-addr.arpa nameserver = publicdns2.isp.net publicdns2.isp.net internet address = 10.10.10.11 publicdns.isp.net internet address = 10.10.10.10 > set type=mx > mydomain.com Server: publicdns.isp.net Address: 10.10.10.10 mydomain.com MX preference = 10, mail exchanger = mail.mydomain.com mydomain.com nameserver = publicdns.isp.net mydomain.com nameserver = publicdns2.isp.net mail.mydomain.com internet address = 20.21.22.23 publicdns2.isp.net internet address = 10.10.10.11 publicdns.isp.net internet address = 10.10.10.10 > set type=a > mydomain.com Server: publicdns.isp.net Address: 10.10.10.10 Nombre: mydomain.com Address: 20.21.22.23 When I test the spf record with http://www.mxtoolbox.com it shows: TXT mydomain.com 24 hrs v=spf1 a mx ptr ip4:20.21.22.23 mx:mail.mydomain.com -all Any clues of what's happening here?

  Read the article

• passwd ldap request to ActiveDirectory fails on half of 2500 users

  - by groovehunter

  We just setup ActiveDirectory in my company and imported all linux users and groups. On the linux client: (configured to ask ldap in nsswitch.conf): If i do a common ldapsearch to the AD ldap server i get the complete number of about 2580 users. But if i do this it only gets a part of all users, 1221 in number: getent passwd | wc -l Running it with strace shows kind of attempt to reconnect My ideas were: Does the linux authentication procedure run ldapsearch with a parameter incompatible to AD ldap ? Or probably it is a encoding issue. The windows user are entered in AD with all kind of characters. Maybe someone could shed light on this and give a hint how to debug that further!? Here's our ldap.conf host audc01.mycompany.de audc03.mycompany.de base ou=location,dc=mycompany,dc=de ldap_version 3 binddn cn=manager,ou=location,dc=mycompany,dc=de bindpw Password timelimit 120 idle_timelimit 3600 nss_base_passwd cn=users,cn=import,ou=location,dc=mycompany,dc=de?sub nss_base_group ou=location,dc=mycompany,dc=de?sub # RFC 2307 (AD) mappings nss_map_objectclass posixAccount User # nss_map_objectclass shadowAccount User nss_map_objectclass posixGroup Group nss_map_attribute uid sAMAccountName nss_map_attribute cn sAMAccountName # Display Name nss_map_attribute gecos cn ## nss_map_attribute homeDirectory unixHomeDirectory nss_map_attribute loginShell msSFU30LoginShell # PAM attributes pam_login_attribute sAMAccountName # Location based login pam_groupdn CN=Location-AU-Login,OU=au,OU=Location,DC=mycompany,DC=de pam_member_attribute msSFU30PosixMember ## pam_lookup_policy yes pam_filter objectclass=User nss_initgroups_ignoreusers avahi,avahi-autoipd,backup,bin,couchdb,daemon,games,gdm,gnats,haldaemon,hplip,irc,kernoops,libuuid,list,lp,mail,man,messagebus,news,proxy,pulse,root,rtkit,saned,speech-dispatcher,statd,sync,sys,syslog,usbmux,uucp,www-data and here the stacktrace from strace getent passwd poll([{fd=4, events=POLLIN|POLLPRI|POLLERR|POLLHUP}], 1, 120000) = 1 ([{fd=4, revents=POLLIN}]) read(4, "0\204\0\0\0A\2\1", 8) = 8 read(4, "\4e\204\0\0\0\7\n\1\0\4\0\4\0\240\204\0\0\0+0\204\0\0\0%\4\0261.2."..., 63) = 63 stat64("/etc/ldap.conf", {st_mode=S_IFREG|0644, st_size=1151, ...}) = 0 geteuid32() = 12560 getsockname(4, {sa_family=AF_INET, sin_port=htons(60334), sin_addr=inet_addr("10.1.35.51")}, [16]) = 0 getpeername(4, {sa_family=AF_INET, sin_port=htons(389), sin_addr=inet_addr("10.1.5.81")}, [16]) = 0 time(NULL) = 1297684722 rt_sigaction(SIGPIPE, {SIG_DFL, [], 0}, NULL, 8) = 0 munmap(0xb7617000, 1721) = 0 close(3) = 0 rt_sigaction(SIGPIPE, {SIG_IGN, [], 0}, {SIG_DFL, [], 0}, 8) = 0 rt_sigaction(SIGPIPE, {SIG_DFL, [], 0}, NULL, 8) = 0 rt_sigaction(SIGPIPE, {SIG_IGN, [], 0}, {SIG_DFL, [], 0}, 8) = 0 write(4, "0\5\2\1\5B\0", 7) = 7 shutdown(4, 2 /* send and receive */) = 0 close(4) = 0 shutdown(-1, 2 /* send and receive */) = -1 EBADF (Bad file descriptor) close(-1) = -1 EBADF (Bad file descriptor) exit_group(0) = ?

  Read the article

• Why can't I play DVDs on Windows 8 Pro with Media Center Pack?

  - by ligos

  I have a laptop with Windows 8 Pro with Media Center (64 bit), but neither Media Player or Media Center can play DVDs. Have I done something wrong? Did the Feature Pack not install correctly? Should this work? Can I somehow uninstall and reinstall the Media Pack? Details So I upgraded by Windows 7 Home Premium laptop to Windows 8 Pro based on Microsoft's low pricing. I also grabbed my free upgrade to Media Pack and followed the instructions on that page to add my feature pack. Alas! I still cannot play DVDs via either Media Center or Player. Various Context Thinking I might need to re-install the pack, I found that I could no longer add any more feature packs (searching for add features settings only shows Turn Windows Features On and Off). Media Centre and Media Player are both enabled in Windows Features. I cannot see any way to remove or downgrade from the Media Pack, nor to add any more feature packs. I installed a codec pack (32bit) from Shark007, which has not allowed me to play DVDs (although did allow me to play various other media files). Media Player can play DTV recorded on another Windows 7 box, but Media Center cannot. VLC plays DVDs OK, but I'd prefer to figure out what the root cause of this problem is. There were no errors or other indications that the Media Pack failed to install; the installation itself was quite smooth. Although I have not checked my event log in detail. Before upgrading to Windows 7, I could play DVDs OK. Screenshots System Information, showing I have Windows 8 Pro with Media Center When playing a DVD, Media Player gives and error: The selected file has an extension that is not recognised by windows... When you click Yes, it fails saying: Windows Media Player cannot find the file... Media Center says: The file type is not recognisd and cannot be played, along with some codec related stuff. I can browse the files OK via My Computer on any video DVD.

  Read the article

< Previous Page | 492 493 494 495 496 497 498 499 500 501 502 503  | Next Page >