Search Results

Search found 15661 results on 627 pages for 'protected mode'.

Page 497/627 | < Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >

  • IP queue buffer

    - by summerbulb
    I seem to have an issue with IP queue. I have a linux machine that I am using to run some experiments. The linux machine is configured to be a router, having two NICs, connecting two other computers, and managing their network traffic. All incoming packages are captured, using iptables, and analyzed by a C application. The application analyzing the packets has a built-in delay, as part of the experiment. So I have one very fast computer sending packets through my linux-router and a (relatively) slow linux-router that analyses and deals with the packets, one by one. This situation leads to the fact that when I fire up a sender application on one of the computers connected to the linux-router, my IP queue on the linux-router gets filled up (almost) instantaneously. The IP queue's max length is currently set to 1024, and if it overflows, the packets are dropped. This is expected and i'm OK with it. But, (and this is where it gets interesting), every now and then I get the following error: "Failed to receive netlink message: No buffer space available" At start, I thought this was due to the IP queue overflow, but after some analysis i found that sometimes I get the error even if the IP queue buffer did not overflow, and sometime I DON'T get the message even though the buffer DID overflow. When I run > cat /proc/net/ip_queue, I get the following table (also used to monitor the IP queue overflow): Peer PID : 27389 Copy mode : 2 Copy range : 65535 Queue length : 0 Queue max. length : 1024 Queue dropped : 1166875 Netlink dropped : 2916 Looking at the last two values, Queue dropped seems to refer to packets that did not manage to get into the IP queue because the buffer was full. I can see this value rise as I bombard the linux-router. Netlink dropped ( as it's name implies :) ) seems to have to do with the error i'm getting. I did my best to search for material on this error, but wasn't able to find anything that seemed to point me in the required direction. Bottom line: Why am I getting this error and what can I do to avoid it?

    Read the article

  • IIS7 ASP.NET application - 2 identical apps in 2 identical app pools, 1 is responsive and 1 is not

    - by Ben
    I have an ASP.NET (v4.0) web app that is installed in a virtual directory (as an application) and is hosted in it's own app pool. This is repeated for each instance of the app (i.e. per customer). The app pools are integrated (not classic) mode and LoadUserProfile is set to true. Otherwise, default settings. Each instance currently has it's own copy of the code/config, and it's own data folder (basic file read/writes). 1 instance of this app runs well (operation used for comparison takes ~4 seconds). Every other instance runs slowly (from 10-25 seconds for the same operation). If I move the slower instance to the "fastest" app pool that instance springs to life. If I move the faster instance into the slower app pool that instance slows to a crawl. The app pools were created in the same way initially - manually. I later used the powershell copy routine to ensure an exact copy of the faster app pool and still the same behaviour. Comparing the apppool.config files shows they are identical barring the virtual directory assignments. There are no shared resources that are being blocked, so far as I can tell, and I tested that by shutting down the performant app pool and restarting... slow is still slow, and then when I restart that app pool (so it's loaded last) it's still faster...

    Read the article

  • Ubuntu hard disk getting SATA errors

    - by Henadzy
    I am getting "UNC" errors on a hard disk on Ubuntu 9.10. It slows down my system, applications have not been responding for a long time. But when I mount the filesystem on another computer, it works properly. disk: SAMSUNG HD161HJ (SATA) syslog: Apr 25 00:28:25 vare6gin kernel: [ 885.773839] ata3.00: exception Emask 0x1 SAct 0x1e SErr 0x0 action 0x6 frozen Apr 25 00:28:25 vare6gin kernel: [ 885.773845] ata3.00: Ata error. fis:0x21 Apr 25 00:28:25 vare6gin kernel: [ 885.773861] ata3.00: cmd 60/08:08:3f:00:ad/00:00:10:00:00/40 tag 1 ncq 4096 in Apr 25 00:28:25 vare6gin kernel: [ 885.773864] res 51/40:24:67:c8:91/40:00:05:00:00/40 Emask 0x9 (media error) Apr 25 00:28:25 vare6gin kernel: [ 885.773871] ata3.00: status: { DRDY ERR } Apr 25 00:28:25 vare6gin kernel: [ 885.773877] ata3.00: error: { UNC } [...snip 3 similar repeats of last 4 lines; see revision history for full log...] Apr 25 00:28:25 vare6gin kernel: [ 885.773970] ata3: hard resetting link Apr 25 00:28:25 vare6gin kernel: [ 885.773974] ata3: nv: skipping hardreset on occupied port Apr 25 00:28:25 vare6gin kernel: [ 886.240073] ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Apr 25 00:28:25 vare6gin kernel: [ 886.256277] ata3.00: configured for UDMA/133 Apr 25 00:28:25 vare6gin kernel: [ 886.256305] ata3: EH complete Apr 25 00:28:27 vare6gin kernel: [ 888.176088] ata3: EH in SWNCQ mode,QC:qc_active 0xF sactive 0xF Apr 25 00:28:27 vare6gin kernel: [ 888.176099] ata3: SWNCQ:qc_active 0xF defer_bits 0x0 last_issue_tag 0x3 Apr 25 00:28:27 vare6gin kernel: [ 888.176102] dhfis 0xF dmafis 0x1 sdbfis 0x0 Apr 25 00:28:27 vare6gin kernel: [ 888.176109] ata3: ATA_REG 0x51 ERR_REG 0x40 Apr 25 00:28:27 vare6gin kernel: [ 888.176113] ata3: tag : dhfis dmafis sdbfis sacitve Apr 25 00:28:27 vare6gin kernel: [ 888.176120] ata3: tag 0x0: 1 1 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176126] ata3: tag 0x1: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176131] ata3: tag 0x2: 1 0 0 1 Apr 25 00:28:27 vare6gin kernel: [ 888.176136] ata3: tag 0x3: 1 0 0 1

    Read the article

  • IIS 6 Windows Authentication in ASP.Net app fails

    - by Kjensen
    I am trying to install an ASP.Net app on an IIS6 webserver. The site requires the user to authenticate with windows, and this works on several other apps on the same server. In IIS I have enabled anonymous access and windows authentication. In web.config, authentication is set to: <authentication mode="Windows"/> and authorization...: <authorization> <allow roles="Users"/> <deny users="*"/> </authorization> Ie. allow all users in role "Users" and deny everybody else. This is the approach that is working with several other apps on the same server. If I run the site, I am prompted for username and password. If I remove the line: <deny users="*"/> I can access the site and everything works - but the user credentials are not passed to the site (Page.User.Identity.Name returns a blank string in ASP.Net). The site has identical (inherited) file permissions as other working sites on the server. The only difference in authentication/authorization between this site and the other working sites is, that this runs Asp.Net 4 (but there are other working asp.net 4 sites on the server as well). What am I missing here? Where should I look?

    Read the article

  • Puppet - Is it possible to use a global var to pull in a template with the same name?

    - by Mike Purcell
    I'm new to puppet. As such I am trying to work my way around the best way to setup my manifests that make sense. Following the DRY (don't repeat yourself) principle, I am trying to load common directives in one template, then load in environment specific directives from a file matching the environment. Basically like this: # nodes.pp node base_dev { $service_env = 'dev' } node 'service1.ownij.lan' inherits base_dev { include global_env_specific } class global_env_specific { include shell::bash } # modules/shell/bash.pp class shell::bash inherits shell { notify{"Service env: ${service_env}": } file { '/etc/profile.d/custom_test.sh': content => template('_global/prefix.erb', 'shell/bash/global.erb', 'shell/bash/$service_env.erb'), mode => 644 } } But every time I run puppet agent --test puppet complains that it can't find the shell/bash/$service_env.erb file, but I double checked that it exists. I know the var is accessible due to the notify statement outputting the expected value, so I suspect I am doing which is not allowed. I know I could have a single template.erb and pass variables to the template, which would work in this case because the custom.sh file is small and not many changes across environments, but for more complex configs (httpd, solr, etc) I'd prefer to access environment specific files. I am also aware that I can specify environment specific module paths, but I'd prefer to just handle this behavior at the template level, instead of having several, closely named directories. Thanks.

    Read the article

  • Problems with 5.1 digital out on Ubuntu 12.04

    - by user895319
    I've recently bought a new PC, installed Ubuntu and am now unable to get 5.1 digital sound working. Simple analogue stereo works fine on both the front and rear connectors. On my old box I connected the coax connection from my soundcard to my surround sound amplifier, set Settings-Sound to "Digital Stereo Duplex" and it worked. My old soundcard doesn't fit in my new machine so I'm using the built-in sound hardware. I'm connecting the combination output socket on the back of the PC via the same cable to my surround amp as before. The MB is an MSI Global H61M-P31 with an RealTek ALC887 sound chip. When I go to Settings-Sound I only see "Headphone Built-in Audio" and "Analogue Output Built-in Audio" - no digitial options. The output from aplay -l is: default Playback/recording through the PulseAudio sound server sysdefault:CARD=PCH HDA Intel PCH, ALC887-VD Analog Default Audio Device front:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Front speakers surround40:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.0 Surround output to Front and Rear speakers surround41:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 5.1 Surround output to Front, Center, Rear and Subwoofer speakers surround71:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog 7.1 Surround output to Front, Center, Side, Rear and Woofer speakers dmix:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample mixing device dsnoop:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct sample snooping device hw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Direct hardware device without any conversions plughw:CARD=PCH,DEV=0 HDA Intel PCH, ALC887-VD Analog Hardware device with all software conversions While googling for ALC887 I've seen some references to "ALC887 -VD Analog" and some to "ALC887 -VD Digital". Does anyone know if I need to force it to chance mode somehow? It's worth mentioning that when I set the output to 5.1 digital surround in Windows 7 on the same machine I still don't get any sound so it's not a unique Linux problem. Thanks for any help.

    Read the article

  • Connect to Nonencrypted Wireless Network Using Ubuntu Commands

    - by Tim
    I failed to connect to an open i.e. nonencrypted wireless network using Ubuntu command lines. Here is what I did: $ sudo /etc/init.d/NetworkManager stop * Stopping network connection manager NetworkManager [ OK ] $ sudo /sbin/ifconfig wlan0 up $ sudo iwconfig wlan0 essid "Cavalier High-Speed 866-4-CAVTEL" $ sudo dhclient wlan0 There is already a pid file /var/run/dhclient.pid with pid 10812 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on LPF/wlan0/00:0e:9b:cd:4e:18 Sending on Socket/fallback DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPREQUEST of 192.168.1.67 on wlan0 to 255.255.255.255 port 67 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 7 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 12 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 21 DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6 No DHCPOFFERS received. Trying recorded lease 192.168.1.67 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms Trying recorded lease 192.168.1.45 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. --- 192.168.1.1 ping statistics --- 1 packets transmitted, 0 received, +1 errors, 100% packet loss, time 0ms No working leases in persistent database - sleeping. $ sudo /sbin/iwconfig wlan0 wlan0 IEEE 802.11bg Mode:Managed Frequency:2.422 GHz Access Point: Not-Associated Tx-Power=27 dBm Retry min limit:7 RTS thr:off Fragment thr=2352 B Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I was wondering what the problem is and how I can do it right? Thanks and regards!

    Read the article

  • IIS crashes with unhandled exception in ASP.NET

    - by SnowCrash
    We had an issue recently with an unhandled exception in an ASP.NET C# application bringing down IIS and all application pools that it was hosting. IIS Manager was unable to restart or stop/start the service and I was unable start IIS again after killing w3wp.exe in the task manager. A system reboot restored IIS to a running state; as a primarily Linux admin, I generally consider an unplanned system reboot to resolve a software error to be an act of high heresy. Is there a way to "harden" IIS so that a faulting application does not affect anything but the request that exposes the fault? Some details on the server and application fault. IIS: 7.5 .NET: 4.0 Windows Server 2008 R2 Faulted on call to System.Net.Dns.Resolve() with a url pointing to a non-existant domain as the argument. (I'm aware that this method is deprecated but the point that a page code issue shouldn't bring down the server still stands) The exception generated was SocketException. The faulting module according to event viewer was KERNELBASE.dll The issue was resolved by wrapping the call in a try-catch, logging the exception and displaying some generic content on the page. I'm hoping that I missed something in the IIS config that would switch it to "production" mode or something.

    Read the article

  • Win7 System folder contains infinitely looping SYSTEM(!) directory

    - by Matt
    My Windows 7 Enterprise computer has been crashing fairly frequently recently, so I decided to boot up in safe mode and run the TrendMicro client I have installed. It froze about 10 minutes into the full system scan, so in the spirit of http://whathaveyoutried.com, I started scanning each folder individually. When I got to ProgramData, the AV failed with an uncaught exception. I then went down a level and tried scanning Application Data, which failed as well. Imagine my surprise when I open the folder just to see the same folder again! As far as I can tell, this folder loop continues indefinitely. (If you are trying to recreate this, keep in mind that ProgramData is a hidden folder.) I'm actually a bit concerned that these are system folders, as this is a brand-new computer with a clean installation. I guess I have three questions: Has anyone else seen/experienced this before? I'm running Win7 SP1. How do I fix this? I've run CHKDSK \F with no success (although it was incredibly slow). What are the ramifications of an infinitely recursive directory? Theoretically speaking, each link takes up memory, so shouldn't I have no space available on my hard drive? (I've got about 180GB left.) I noticed that the tree view on the left only shows the "linked folder" icon on the deeper folders--does this mean anything special? (I've circled the icons or lack thereof in red.) How can the OS even resolve this aberration? And above all, what would happen if I were to select "Expand all folders"??? :P Matt

    Read the article

  • GlusterFS as elastic file storage?

    - by Christopher Vanderlinden
    Is there any way to run GlusterFS in a replicated mode, but with the ability to dynamically scale the volume up and down? Say you have 3 servers all running glusterd. your Gluster volume would have to be setup with replica 3 gluster volume create test-volume replica 3 192.168.0.150:/test-volume 192.168.0.151:/test-volume 192.168.0.152:/test-volume You would then mount it as say \mnt\gfs_test What happens when I want to add 2 more servers to the storage pool and then also use them in this volume? Is there any easy way to expand the volume AND increase that replica count to 5? My end goal is to run this on EC2 instances, say 3 Apache front ends, with the webroot setup on the gluster volume mount. My concern is that if I ever need to spin up a server, I would want the server to not only be an additional Apache front end, but also another server in the gluster file system, adding to fault tolerance as well as possibly giving a slight boost in read speed. Maybe there are better options that would fit the bill here? Thanks.

    Read the article

  • I have enabled hidden administrator in Win 7 home, but programs still dont work.

    - by Angela
    I have Windows 7 Home Premium, and would like to do some maintenance tasks such as running Disk Defragmenter. However, this and other programs and applications that I'm accustomed to using are now blocked. For these programs, there is a shield icon next to their icons and nothing happens when I click on them. I notice that the screen blinks slightly, but I do not get prompted for a password and the program still does not run. It seems these programs may only be accessible through an Administrator account. However, right-clicking and selecting "Run As Administrator" does not work. After some research, I found a way to enable the hidden built-in Administrator account. I booted the computer into safe mode. In the command prompt, I typed net user administrator /active:yes. I gave the account a password. I rebooted the system. There is now an Administrator account on the home screen. However, the locked programs behave no differently for me when I use this account. What could cause this problem? How can I fix it?

    Read the article

  • Installed Paragon HFS+ for Windows 8, now my pc won't recognize the external firewire drive

    - by Steve
    I'm not incredibly knowledgeable about computers and I really need some help. Just got a Seagate external firewire drive this morning. I downloaded the necessary pc driver (Paragon HFS+ for Windows 8) through their website per the instructions that came with the drive. After installation, I restarted and the pc recognized the firewire drive just fine. About three hours into copying files from my pc to the firewire drive, it gave me an error and told me the files couldn't be copied. When I clicked to get out of the message, the computer crashed. After an hour of it trying to repair itself in safe mode, it restored me to an earlier version before the system crashed. Here's my current dilemma: The Paragon HFS+ is still showing up in my programs as installed, but the Device Manager is not recognizing the drive. When I try to uninstall and reinstall Paragon, it interrupts me with a message saying "The setup must update files or services that cannot be updated while the system is running" and basically gives me the finger. I have no idea what to do now, as it won't let me uninstall and reinstall Paragon, and I have no idea why it crashed my computer in the first place. Is there possibly another Mac - PC firewire driver I can try downloading instead? I really don't know what I'm doing and any help would be greatly appreciated.

    Read the article

  • ubuntu 9.10 installer doesn't recognize the hard drive

    - by dan
    I downloaded Ubuntu 9.10 x86_64 and am trying to install it on a fairly modern system with a Gigabyte GA-MA770-UD3 motherboard. Ubuntu 9.04 installed fine and still will when I stick that disc in, but 9.10 doesn't see my hard drive (western digital 250GB). If I boot from the disc, I can install gparted and it does recognize the drive, but when I try to start the install process from the live disc, Ubuntu again doesn't recognize the hard drive. I checked /var/log/messages and see this: Nov 12 17:28:08 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was bad, boot with 'nodmraid'. Nov 12 17:28:08 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. Nov 12 17:28:08 ubuntu activate-dmraid: no raid sets and with names: "nvidia_ciiajheb-0" Nov 12 17:28:08 ubuntu activate-dmraid: ERROR: either the required RAID set not found or more options required. I checked my BIOS, SATA is enabled and is set to IDE mode, so there shouldn't be software RAID, but nonetheless, I added nodmraid to the boot line and tried again. It still doesn't recognize the drive. I checked /var/log/messages again and now see this: Nov 12 17:49:38 ubuntu activate-dmraid: Serial ATA RAID disk(s) detected. If this was boad, boot with 'nodmraid'. Nov 12 17:49:38 ubuntu activate-dmraid: Enabling dmraid support Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Nov 12 17:49:38 ubuntu activate-dmraid: WARNING: dmraid disabled by boot option Any ideas on things to try? I've tried all of the various BIOS settings for SATA. IDE,RAID, etc. Nothing seems to work.

    Read the article

  • VLAN Tagging Traffic on Cisco Switch

    - by David W
    I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

    Read the article

  • Ubuntu Natty 11.04, Turning the wireless switch off; switches it off permanently!

    - by ZiGi
    i'm using an hp pavilion dv2000 i turned the wifi switch off by mistake, the LED turned orange and the wifi got disconnected. and now when i turn the switch on, it remains orange and the wifi still isn't functional. this happened before; i found a fix that worked searching google. it was done via terminal commands and i didn't have to download anything but i can't find the solution anymore! wlan0 shows up when i use: :~$iwconfig #BLA BLA BLA #... wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off more results: :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: yes Hard blocked: yes :~$ sudo rfkill unblock all :~$ rfkill list all 1: phy0: WirelessLAN Soft blocked: no Hard blocked: yes :~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operation not possible due to RF-kill it's still hard blocked! even though the switch is turned on; gives the same result eitherways a direction to a page with a working solution is a much appreciated answer!

    Read the article

  • Windows is very slow with my new SSD

    - by Maksym H.
    I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

    Read the article

  • ESXi 5 Guests will not boot

    - by Adrian
    I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. Note: Investigation eventually determined that problem was with the VMware client on a Lenovo Edge laptop, the only Windows box available in a Linux IT shop. vSphere Client v4 and v5 duplicated behavior on the Lenovo Edge. As indicated in the comment to the accepted answer, replacing the workstation with one using different video was the "fix" for this particular issue. The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. No errors in the Events tab. Switching Guest from BIOS to EFI makes no difference. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspicious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space. Edit 4: Guests copied from my old ESXi 4 server DO NOT boot on the ESXi 5 system. Initially it complains about too little Video RAM being configured for the default 2500x1600, but it still doesn't work properly even after I bump the Video RAM settings or switch it to Auto-Detect.

    Read the article

  • Weirdly high ping on direct ethernet connection?

    - by Antriel
    I bought new Lenovo IdeaCentre H430 pc and I'm having problem with high pings. Windows 7 with on-board realtek NIC. Fresh install, fully updated, drivers installed from included CD. When I start pinging router (direct 1Gb ethernet connection, 1 hop), pings start at <1ms (which is fine) and after a while they jump to 300-1000ms. I loaded up live ubuntu to test if the problem might be in HW. It's not, in ubuntu pings were always <1ms. I also noticed that when I start using connection somehow, pings go down to 1ms, but go back up when I stop using it (tested by accessing live camera feed on LAN). Power Options set to max performance. I disabled Interrupt Moderation on the NIC, didn't help. I tested it in the safe mode with networking, same problem there. It slows down our client-server based programs and I have no idea what's causing it. All I could google up was that disabling Interrupt Moderation would help, it didn't though. Anyone had similar problems? tl;nr: Computer is giving high pings to router when idle and normal pings when network is under load, it slows down our software significantly.

    Read the article

  • How to set TV-out options under Linux of an Geforce 9600 GT video card

    - by polemon
    I'm using the TV-out connector of my Geforce 9600 GT to connect it to an old TV set. It's obviously in Composite mode, the other two cables of Component video are dead, only Pb/VIDEO labeled one gives me a signal. The picture appears black/white on the TV, I presume it's because the video card gives me an NTSC signal, but it's a PAL tv set. How do I change the TV-out from NTSC to PAL? My Component to SCART adapter hasn't arrived yet, but I think I should be able to set manually, whether the signal should be Composite or Component. How do I switch modes of the TV-out, between Component and Composite? I'm running Linux, so it's probably some settings I need to make in xorg.conf. Edit: I got this far: I need to set in the "Device" section of my xorg.conf: Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" The whole section looks like this now: Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 9600 GT" Option "AddARGBGLXVisuals" "True" Option "TVStandard" "PAL-B" Option "TVOutFormat" "COMPOSITE" EndSection How can I list all available settings for "TVStandard" and "TVOutFormat"?

    Read the article

  • /usr/bin/install hangs, apparently due to SELinux

    - by Cooper
    I'm trying to use the GNU coreutils install utility, however it is hanging: /usr/bin/install -v test_file test_dir/ `test_file' -> `test_dir/test_file I see the same behavior whether I run as a normal user, or root/sudo. I ran an strace -f, and this is the end of the output: ... read(4, "<username>\t-d\tsystem_u:object_r:ho"..., 4096) = 2197 <0.000012> brk(0x6e3b1000) = 0x6e3b1000 <0.000009> mmap(NULL, 29138944, PROT_READ|PROT_WRITE, MAP_PRIVATE|MAP_ANONYMOUS, -1, 0) = 0x2abd831ae000 <0.000014> munmap(0x2abd815dd000, 29138944) = 0 <0.003466> The read() is reading from /etc/selinux/targeted/contexts/files/file_contexts.homedirs, apparently successfully. It appears that the process is hanging right after the munmap, but continues to eat 100% CPU. My two questions are: 1) Any good way to see what is going on with the process? I'm currently too lazy to compile a debug version of install I can run gdb on - but a strong suggestion in an answer here may motivate me to do so if needed. 2) Any idea what the SELinux issue could be? I'm not too familiar with SELinux. Additional info of possible relevance: # ls -Z drwxr-xr-x my_user 7001 user_u:object_r:user_home_t test_dir -rw-r--r-- my_user 7001 user_u:object_r:user_home_t test_file # id ... context=user_u:system_r:unconfined_t # uname -a Linux hostname 2.6.18-238.1.1.el5 #1 SMP Tue Jan 4 13:32:19 EST 2011 x86_64 x86_64 x86_64 GNU/Linux I am suspicious that SELinux + Quest Authentication Services (QAS) is causing the issue. QAS is generally well behaved, but it did cause the /etc/selinux/targeted/contexts/files/file_contexts.homedirs to get quite large (~18k users, @23 lines per user) Update: install -v -Z user_u:object_r:user_home_t file dir/ seems to work. Can anyone suggest why, given that SELinux is in permissive mode (see comments).

    Read the article

  • Reducing both pagfile.sys and hiberfil.sys in Windows 7

    - by greenber
    I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

    Read the article

  • How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

    - by sblair
    Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

    Read the article

  • Keyboard doesn't function after Fedora 17 update

    - by mickburkejnr
    I updated my Fedora 16 installation to Fedora 17 on Saturday, and the update worked without reporting any errors. I carried on working on the machine in question and then switched the computer off. Last night I went back on the computer, I switched it on and got to the log in screen. At this point I tried to type in my password but the keyboard wouldn't work. I unplugged it (it's a PS/2 keyboard) and plugged it back in. The lights flashed for a split second but the keyboard still wouldn't work. I then plugged the keybaord in to a USB to PS/2 adapter, and the keyboard still wouldn't work. I restarted the computer and tried to access the BIOS and I was able to do so. So the keyboard doesn't seem to be faulty, it just doesn't work when Fedora boots in to the GUI interface. I did try to boot in to the "recovery mode" of Fedora, and the keyboard works here with no problem. As I still have access to Fedora via a terminal interface, is there anything I can do to fix the keyboard problem via the terminal without having to reinstall Fedora?

    Read the article

  • Sync desktop Mac environment to laptop

    - by Andrew Vit
    I spend the majority of my time working at my desktop Mac, which I have configured for my web development environment. My spouse has a MacBook for casual use, and I occasionally steal it back when I need to work off-site, or when travelling. The question is how to best synchronize the two so I can switch between them more readily. I've solved a few obvious things by using online services: Email is hosted on IMAP. Working files are in Dropbox. Source code is managed in git. However, the following are things I always miss when jumping on the laptop: Installed Applications (current versions) Installed libraries & utilities (/usr/local) Apache VirtualHosts & other configurations (/etc) Disk image files for VMs My current method is to connect the MacBook via Firewire target mode and rsync the /Users/me home directory, and then cherry-pick the other items I need from Applications, /etc and /usr/local. The problem with this method is that it can be very time consuming due to things like my virtual machine image files, cached emails, etc. How can I make this faster & easier? Can you recommend a solution for configuration management (so I can repeatably install & configure the same software on both), or synchronization (so I can bring the MacBook up to date nightly, over our home network)?

    Read the article

  • Virtualbox port forwarding with iptables

    - by jverdeyen
    I'm using a virtualmachine (virtualbox) as mailserver. The host is an Ubuntu 12.04 and the guest is an Ubuntu 10.04 system. At first I forwarded port 25 to 2550 on the host and added a port forward rule in VirtualBox from 2550 to 25 on the guest. This works for all ports needed for the mailserver. The guest has a host only connection and a NAT (with the port-forwarding). My mailserver was receiving and sending mail properly. But all connections are comming from the virtualbox internal ip, so every host connection is allowed, and that's not what I want. So.. I'm trying to skip the VirtualBox forwarding part and just forward port 25 to my host only ip of the guest system. I used these rules: iptables -F iptables -P INPUT ACCEPT iptables -P OUTPUT ACCEPT iptables -P FORWARD ACCEPT iptables -t nat -P PREROUTING ACCEPT iptables -t nat -P POSTROUTING ACCEPT iptables -A INPUT --protocol tcp --dport 25 -j ACCEPT iptables -A INPUT -i lo -j ACCEPT iptables -A INPUT -s 192.168.99.0/24 -i vboxnet0 -j ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -t nat -A PREROUTING -p tcp -i eth0 -d xxx.host.ip.xxx --dport 25 -j DNAT --to 192.168.99.105:25 iptables -A FORWARD -s 192.168.99.0/24 -i vboxnet0 -p tcp --dport 25 -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.99.0 -o eth0 -j MASQUERADE iptables -L -n But after these changes I still can't connect with a simple telnet. (Which was possible with my first solution). The guest machine doesn't have any firewall. I only have one network interface on the host (eth0) and a host interface (vboxnet0). Any suggestions? Or should I go back to my old solution (which I don't really like). Edit: bridge mode isn't an option, I have only on IP available for the moment. Thanks!

    Read the article

< Previous Page | 493 494 495 496 497 498 499 500 501 502 503 504  | Next Page >