Search Results

Search found 408 results on 17 pages for 'broadcom'.

Page 5/17 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Wireless networks are not detected at start up in Ubuntu 12.04

    - by Kanhaiya Mishra
    I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

    Read the article

  • m not able to connect to wifi network

    - by Broken Heart
    i had tried every code every idea every thing but i failed wiireless driver broadcom bcm43412 but when i checked pci-id it show not supported my pci id is 14e4:4365 and chip id is BCM43142 i tried edit connection myself to olso but i cannt wat to put in clone mac adress place? device mac adress is the router mac adress but what is clone mac adress i had placed my laptop mac adress in place of clone mac adress bt it doesnot work tried every thing but it not work checked additional driver by going system settings it doesnot contain any drivers,tried internet by cable then it connects then how sholud i correct this plz tell

    Read the article

  • No firmware found for b43 wireless controlloer (BCM4318) on a Dell Latitude D610

    - by Stanton.Sculpture
    Trying to get my 03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) working. I just reformated and installed 12.04 on this old Windows XP machine, and I don't know where to get the firmware for this. This is what I got when I typed sudo lshw -c network: http://pastebin.ubuntu.com/1041161/ Also, when I go to additional drivers in the system settings, no proprietary drivers show up. Any help I can get on this would be Great, Thanks!

    Read the article

  • No Wireless Networks, BCM4313 [duplicate]

    - by TalonPlz
    This question already has an answer here: How to Install Broadcom Wireless Drivers (BCM43xx) 38 answers Just bought this little Asus 10 inch laptop that came with Ubuntu 12.04. Everything at my home was fine: Wireless identified and connected. As soon as I went to my girlfriend's house the trouble started. I couldn't connect to wireless (authentication... times out and asks for authentication) I started doing internet searching, tried a few solutions posted on line using terminal commands. No solutions. I decided to upgraded to 12.10-13.04 and that left me with a worse problem: I can no longer see ANY networks what so ever. Wireless card is ON, with out a doubt. Wired connection works. I have been fumbling with driver versions to no .avail, and have no idea which driver I am currently running I have a vague idea of what terminal lines to run: lshw: resources: irq:17 memory:f7d00000-f7dfffff *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth2 version: 01 serial: dc:85:de:56:c4:ea width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=6.20.155.1 (r326264) latency=0 multicast=yes wireless=IEEE 802.11abg resources: irq:17 memory:f7d00000-f7d03fff iwconfig: eth1 no wireless extensions. eth2 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off lo no wireless extensions. I am new and excited to start my Ubuntu and Linux life and this is only the first of my few hic cups i am sure! :) Thanks all UPDATE: Report from 2nd answer talon@Black1015E:~$ sudo apt-get remove --purge bcmwl-kernel-source [sudo] password for talon: Reading package lists... Done Building dependency tree Reading state information... Done Package 'bcmwl-kernel-source' is not installed, so not removed 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. talon@Black1015E:~$ wget http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb --2013-10-22 18:50:32-- http://us.archive.ubuntu.com/ubuntu/pool/restricted/b/bcmwl/bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb Resolving us.archive.ubuntu.com (us.archive.ubuntu.com)... 2001:67c:1562::15, 2001:67c:1562::13, 2001:67c:1562::14, ... Connecting to us.archive.ubuntu.com (us.archive.ubuntu.com)|2001:67c:1562::15|:80... connected. HTTP request sent, awaiting response... 200 OK Length: 1181334 (1.1M) [application/x-debian-package] Saving to: ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ 100%[======================================>] 1,181,334 3.37MB/s in 0.3s 2013-10-22 18:50:33 (3.37 MB/s) - ‘bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb’ saved [1181334/1181334] talon@Black1015E:~$ arvh No command 'arvh' found, did you mean: Command 'arch' from package 'coreutils' (main) arvh: command not found talon@Black1015E:~$ arch x86_64 talon@Black1015E:~$ sudo dpkg -i bcmwl*.deb Selecting previously unselected package bcmwl-kernel-source. (Reading database ... 171895 files and directories currently installed.) Unpacking bcmwl-kernel-source (from bcmwl-kernel-source_5.100.82.112+bdcom-0ubuntu3_amd64.deb) ... Setting up bcmwl-kernel-source (5.100.82.112+bdcom-0ubuntu3) ... Loading new bcmwl-5.100.82.112+bdcom DKMS files... First Installation: checking all kernels... Building only for 3.8.0-32-generic Building for architecture x86_64 Building initial module for 3.8.0-32-generic Done. wl: Running module version sanity check. - Original module - No original module exists within this kernel - Installation - Installing to /lib/modules/3.8.0-32-generic/updates/dkms/ depmod........ DKMS: install completed. Error: Module b43 is not currently loaded Error: Module b43legacy is not currently loaded Error: Module ssb is not currently loaded Error: Module bcm43xx is not currently loaded Error: Module brcm80211 is not currently loaded Error: Module brcmfmac is not currently loaded update-initramfs: deferring update (trigger activated) Processing triggers for initramfs-tools ... update-initramfs: Generating /boot/initrd.img-3.8.0-32-generic rebooting now

    Read the article

  • Wireless device bug on 13.10. BCM4313 registers as eth1 instead of wlan0 and no internet access

    - by user205691
    My Hotel wiFi requires me to login with a username & password after connecting to the hotspot. So, my browser would open a page with username & passwrd fields to login and then connect to internet. But unfortunately, firefox & chromium dont seem to work. i dont think it is browser related but a setting for the wifi router or driver which is creating this issue. using Broadcom 801.11 STA wireless driver (proprietary). tried open source as well but same result !! The image linked below shows my wifi connection setting & Chromium. The login page itself comes up after a long time and after entering the credentials, it keeps loading for ever !! it is the same case for every other browser.. so i dont think its browser issue but something to do with wifi setting or network manager stuff.. interestingly, i am able to connect to WiFi networks with WPA key without any issue. Adhoc hotspot is a problem and that is my regular home network :( .. I hope i can get some help solving this issue ! I have tried repeating the same hotspot after login from my android, by creating a virtual repeater with WPA key and it works. I can browse on ubuntu using this method.. but cant be doing this regularly ! I tried loading the same login page of the hotel wifi while browsing through my repeater wifi created on mobile and screen shot attached below. the page loads up quick and easy.. so this means something is wrong with the way network manager handles adhoc connectivity & login ?? i installed wicd0 but it crashes on startup and not helpful at all ! Screenshot of Chromium page Login page with repeated hotspot ifconfig in my terminal results: krishna@krishna-HP-ENVY-4-Notebook-PC:~$ ifconfig eth0 Link encap:Ethernet HWaddr 28:92:4a:1d:54:fa UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) eth1 Link encap:Ethernet HWaddr e0:06:e6:89:fa:49 inet addr:10.24.1.71 Bcast:10.24.1.255 Mask:255.255.255.0 inet6 addr: fe80::e206:e6ff:fe89:fa49/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10940 errors:0 dropped:0 overruns:0 frame:348431 TX packets:6611 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7669631 (7.6 MB) TX bytes:864195 (864.1 KB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2146 errors:0 dropped:0 overruns:0 frame:0 TX packets:2146 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:166120 (166.1 KB) TX bytes:166120 (166.1 KB) I wonder why is the wireless configured under eth1 ? I think this is a bug with earlier ubuntu versions, but is this normal in 13.10 or is there a wrong configuration here ? The wireless device in my pc is BCM4313 and i have installed the bcmwl-kernel-sources, wireless-tools to support the device. i also reinstalled the bcmwl-kernel as suggested on broadcom website, via synaptic package manager. Nothing has changed this situation ! I tried booting into liveUSB and then ifconfig results show wireless under wlan0. But then the wireless connects and loads the login page. So is the problem with the device configuration now ? i really want to get this fixed before i start configuring the other stuff like ATI graphics and such on the laptop for overheating.. lack of internet access is too bad a bug for me :P any help is appreciated!

    Read the article

  • HP Compaq 2510p wireless disabled by hardware switch

    - by mylovelyhorse
    I have an HP Compaq 2510p laptop running ubuntu 12.04 LTS. ubuntu reports that wireless is disabled by means of a hardware switch. There is a 'soft-key' button on the laptop to control the physical wireless hardware but this does not respond. There is no other button, slider, (fn)+ combination to control the physical wireless hardware. There is no BIOS function to disable wireless (and on XP - previous OS - wireless functioned fine). mike@ubuntu:~$ rfkill list all 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no Running rfkill unblock all doesn't change things and I can see no way to change use from 0: to 1: (if that's even possible - or desirable - in the first place). I have checked for additional drivers and the Broadcom proprietary wireless driver is already installed and has a green light. Essentially, I believe I need to make the HP 'soft-keys' work - or at least the wireless card toggle. Advice gratefully received. Cheers M

    Read the article

  • Wireless iwconfig rate auto too low

    - by Jamie Kitson
    Hi, left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 24M or even 48M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Would adding iwconfig eth1 rate 24M to rc.local be the right way to force it at boot? Output from iwconfig when rate=auto: eth1 IEEE 802.11 ESSID:"honeypot" Mode:Managed Frequency:2.417 GHz Access Point: xxx Bit Rate=1 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=5/5 Signal level=-47 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:2 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Thanks, Jamie

    Read the article

  • Wifi hotspot to connect to Android using non-AP supported cards

    - by 3l4ng
    I'm running Ubuntu 13.10 64b on a Dell Inspiron N5010. My wireless device (found using lspci) is Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01). I bought a new android phone and want to connect to Internet by using the laptop as a Wireless Access Point (ad-hoc doesn't work with Android). I tried following tutorials like the one at How to setup a wi-fi hotspot (access point mode)?. The relevant output from iw list was Supported interface modes: * IBSS * managed Running sudo hostapd /path/to/conf/file gave me (eth1 is the wireless, verified by iwconfig) Failed to create interface mon.eth1: -95 (Operation not supported) Could not set channel for kernel driver eth1: Unable to setup interface. Could not connect to kernel driver. I am able to use Connectify and Virtualrouter on Windows, and the phone works great. How do I get an access point running on Ubuntu? I'm open to other alternatives as well.

    Read the article

  • Wifi not working for Ubuntu 14.04

    - by user286975
    I have installed the Ubuntu 14.04 on Dell Vostro 2520 laptop. Wifi is not working after installation. Tried several methods to install but nothing happens. Vostro-2520:~$ sudo rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no Vostro-2520:~$ iwconfig usb0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. The hardware is Broadcom 802.11 bcm43142. Please help to solve this issue.

    Read the article

  • Wi-fi interface fails to authenticate on secured networks

    - by Eduardo Bezerra
    the problem is that I can't connect to wireless networks that have security enabled. I can connect fine to the unsecured network of my university, but not to the secured one in the same building. Also, it fails to connect to my home wireless router, which uses wpa2 encryption. Any ideas? I have a Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01), with pci id [14e4:4353], running Ubuntu 12.10 on a macbook pro 6,2. I'm using bcmwl-kernel-source package with kernel module wl to enable my wi-fi device.

    Read the article

  • Ubuntu 12.04, can't find my home wifi network

    - by Anton
    I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

    Read the article

  • Dell wireless not working after upgrade

    - by Omer Saeed
    So, the short version of my sad story is that I tried upgrade Ubuntu to 12.04 and wireless driver has stopped working. I have tried all the solutions but nothing seem to be working. When I try to install my wireless from "Additional Drivers" Its says: Sorry, installation of this driver failed. Please have a look at the log file for details: /var/log/jockey.log The lspci command gives me the following info about wireless: 0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01) I have tried removing bcm drivers and reinstalling, but nothing seems to be working. rfkill is good too.

    Read the article

  • ubuntu is so damn frustrating! [on hold]

    - by Bob Kathy Mosca
    3 damn weeks I've been trying to follow all the suggestions I can find to get that stupid broadcom bcm4312 to work and still nothing! I think you ubuntu users have forgotten what its like to really know NOTHING about computers. You advice is next to worthless and you all seem to "assume" the new user is at least (what YOU consider) "computer literate" ...think again. No wonder that crap system from microsoft dominates! They know the public is stupid so their system does this crap for you! damn! what a pity too

    Read the article

  • Slow Wireless Reconnect After Suspend

    - by nrhine1
    I a Broadcom 4312 using the STA drivers, I reinstalled ubuntu because the b43 drivers were giving me a huge hassle along with some weird kernel issues. My wireless speed is fine, everything works well, except upon restart of computer and after taking the computer out of suspend. It takes about 30-45 seconds for the wireless to reconnect, and I think it is a driver issue (I clicked on the network manager at the top and for about 30 seconds there are no wireless networks listed.) I tried this advice already: http://lilserenity.wordpress.com/2007/10/31/fix-ubuntu-dropping-wireless-on-suspendhibernate-resume/ which basically says to change this: STOP_SERVICES="" to STOP_SERVICES="networking" in the file /etc/default/acpi-support This did not help anything. Something to note is that the issue does not occur when I am logging back in after already logging in once and logging out.

    Read the article

  • How to fix additional STA driver installation error on 12.04

    - by nibl
    I have a Broadcom BCM4313 wireless driver. It worked fine under 11.04 and the upgrade to 11.10 also went smoothly. The 12.04 upgrade has broken the wireless connection. I've seen several posts about this and all presume you can activate the STA drivers, but that's where it fails on this machine. The log is in /var/log/jockey.log: WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted (repeat of last error several times) Any ideas how to proceed?

    Read the article

  • Cant find one particular wireless network. Worked before, but sudenly stopt working.

    - by Haakon
    My first question here. My problem is: I cant find my wireless network at home. Situation: It worked fine 7 days ago. It works with a cable(wierd). I find the network on my ipad/phone. I can connect to wireless hotspot network form my phone and wireless at my university, and it works fine. I can connect to the network in windows What I have tried: Tried this Strange network issue; works on windows, but not on ubuntu, works on campus wireless, but not at home (removing resolve.conf). Hardware and software: I have a Broadcom card Use dual boot ubuntu 12.04 - windows 7 Things I did to make wireless work: blacklist brcmsmac blacklist bcma blacklist b43 blacklist ssb Can anyone help me? I'm about to kill myself(not literary)!! I'm not that good in linux so go gentle on me:)

    Read the article

  • BCM4313 Wireless on Ubuntu Server 12.04

    - by KJ Tsanaktsidis
    I'm trying to run an old netbook with Broadcom BCM4313 wireless as a print server with Ubuntu Server 12.04. Setting up the wireless without the GUI, however, is proving problematic. I do think however I've narrowed down the problem. I've tried both the wl driver (from bcmwl-kernel-source) as well as the (included) brcmsmac driver. With both of them, when I issue the command iwlist wlan0 scanning (eth1 for wl), I only see neighbouring networks- not my own. I believe this might be because my networks are n-only, but my neighbouring networks are mixed mode (I suspect this because the output of iwlist wlan0 scanning shows "Bit Rates" only as high as 54 Mb/s). Any ideas how to go about getting this thing to connect?

    Read the article

  • Can't connect to wireless without typing sudo modprobe b43 in terminal

    - by user90889
    I just upgraded to 12.04 on an old ACER Travelmate 5320 using Broadcom 4311. I wasn't able to connect to the internet through the wireless for a few days. It didn't even display wireless networks. I was finally able to make it work by following the instructions found here: http://linuxwireless.org/en/users/Drivers/b43#supported However, each time I log on to the computer I have to go to the terminal and type sudo modprobe b43 to make the wireless work. Is there somehow I can avoid this? I have used Ubuntu for many years but always relied on other people to help me with the technical stuff. The terminal is alien to me so I literally follow online forum instructions without knowing what I'm doing. Also, I tried many many things before I managed to make it work. So I'm worried I may have installed something that now conflicts with whatever the sudo modprobe b43 does. Thank you

    Read the article

  • Ubuntu 12.04 wired ethernet not working and wireless not working, How do I fix it?

    - by Eloy
    I am new to ubuntu. I recently installed the latest ubuntu for desktop from http://www.ubuntu.com/download. I was very excited to start using ubuntu until I booted the computer and saw that i couldn't connect to the internet at all. I have spent hours trying to figure this out. I keep running into people suggesting installing drivers etc. I have tried about everything and nothing seems to work. I have the ethernet cable connected to the computer but it doesn't recognize it. I ran the following: lspci | grep -i eth and I get this 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5752 Gigabit Ethernet PCI Express (rev 02) Any help would be much appreciated. I am kind of bummed I have spent all this time tyring to get the internet to work and haven't even gotten to use the power of ubuntu Update copied from comment: Changing the Ethernet cable to a different one fixed the problem.

    Read the article

  • BCM4313 partially working on Toshiba Satellite R630 (Ubuntu 12.10)

    - by Denis
    New to Ubuntu. During installation, the computer identified the wifi card and asked me to connect to the network. I did. After the first restart the wifi was working and I could see networks and connect to them. After the second restart the wireless has VANISHED. Still, the Broadcom STA drivers are enabled in system settings/additional drivers. Tried to restart 5 more times- no effect. I have studied very many topics on askubuntu but none of them work.

    Read the article

  • two possible wifi devices competing, one is hard blocked - unable to connect wireless

    - by patrickmw
    blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

    Read the article

  • two possible wifi devices competing, one is hard blocked

    - by patrickmw
    blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

    Read the article

  • Can't connect to hidden network with BCM4313

    - by poomerang
    The wireless works fine with all the other wi-fi nets I have tried, the only problem is with this hidden network. I should add it's the only hidden network I've tried, so I am not sure if the problem is it being hidden or somethings else, but I've checked the settings of NetworkManager against another Ubuntu system (which can connect) and they appear to be the same, passphrase included. The network is using WPA2 Personal with AES encryption, I don't know how to check this setting but I believe it's the usual for WPA2, and therefore usually not a problem. Also, I can connect through ethernet, which should exclude any blacklisting of my device, I believe. I usually use brcmsmac drivers, I've tried also STA but the result is the same. I've also tried the suggestion from Unable to connect to hidden SSID with no luck output of lspci -v is 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) Subsystem: Askey Computer Corp. Device 7175 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at d4000000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac

    Read the article

  • Having trouble installing Bradcom STA driver

    - by user192881
    I just installed Ubuntu and love it so much, its so fast now. But I have a problem connecting to the internet. I checked and saw I have to install the driver Broadcom STA wireless driver but every time I do try to install it it says: Sorry, installation of this driver failed. Please have a look at the log files for details: /var/log/jockey.log I went to the terminal and copy and pasted the log file name. and when I did it, it said I have no permission to access this file. I checked on the forums that I have to be on a wired connection. So I plugged my laptop into my router and I got internet then tried to install the driver again. And it was loading then when it got to the end the same message popped up. Also I have one of those little USB router things you plug into the computer and it gives you internet I have been using that but its to slow. So I want to use the one in my computer but cant. Also I tried the command: sudo modprobe wl and when i type that command in it says: FATAL: Module wl not found Also I'm using Ubuntu 12.04

    Read the article

  • After upgrade to 12.04 wireless keeps dropping on BCM4312

    - by Sheket
    I know there are plenty of questions very similar to these, but I've tried practically everything and it still isn't working. Some solutions get the wireless connection working, but it goes very slow and drops after a few minutes. Then it won't reconnect and keeps asking for password. Hope you can help me. Thanks in advance. This is the output for sudo lshw -C network *-network description: Network controller product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: driver=b43-pci-bridge latency=0 resources: irq:18 memory:f0300000-f0303fff *-network description: Ethernet interface product: AR8132 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth1 version: c0 serial: 00:23:5a:9b:6e:b1 size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.0.106 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:42 memory:f0200000-f023ffff ioport:a000(size=128) *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: 00:24:2c:83:f0:81 capabilities: ethernet physical wireless configuration: broadcast=yes driver=b43 driverversion=3.2.0-30-generic firmware=478.104 link=no multicast=yes wireless=IEEE 802.11bg And for lsmod | grep b43 b43 342643 0 mac80211 436455 1 b43 cfg80211 178679 2 b43,mac80211 bcma 25651 1 b43 ssb 50691 1 b43 And for rfkill list 5: phy0: Wireless LAN Soft blocked: no Hard blocked: no

    Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >