Search Results

Search found 632 results on 26 pages for 'fd'.

Page 5/26 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• How to create partition when growing raid5 with mdadm.

  - by hometoast

  I have 4 drives, 2x640GB, and 2x1TB drives. My array is made up of the four 640GB partitions and the beginning of each drive. I want to replace both 640GB with 1TB drives. I understand I need to 1) fail a disk 2) replace with new 3) partition 4) add disk to array My question is, when I create the new partition on the new 1TB drive, do I create a 1TB "Raid Auto Detect" partition? Or do I create another 640GB partition and grow it later? Or perhaps the same question could be worded: after I replace the drives how to I grow the 640GB raid partitions to fill the rest of the 1TB drive? fdisk info: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe3d0900f Device Boot Start End Blocks Id System /dev/sdb1 1 77825 625129281 fd Linux raid autodetect /dev/sdb2 77826 121601 351630720 83 Linux Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc0b23adf Device Boot Start End Blocks Id System /dev/sdc1 1 77825 625129281 fd Linux raid autodetect /dev/sdc2 77826 121601 351630720 83 Linux Disk /dev/sdd: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x582c8b94 Device Boot Start End Blocks Id System /dev/sdd1 1 77825 625129281 fd Linux raid autodetect Disk /dev/sde: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xbc33313a Device Boot Start End Blocks Id System /dev/sde1 1 77825 625129281 fd Linux raid autodetect Disk /dev/md0: 1920.4 GB, 1920396951552 bytes 2 heads, 4 sectors/track, 468846912 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk identifier: 0x00000000

  Read the article

• Unicorn 3.3.1 and Rack 1.1.0 issues?

  - by user41422

  I'm upgrading from the Ruby Enterprise Edition 1.8.6 to the latest 1.8.7 version with Unicorn to facilitate an upgrade to Rails 2.3.10, and am running into some issues. Should I uninstall the older versions of these gems? Here's the log messages: I'm upgrading from the Ruby Enterprise Edition 1.8.6 to the latest 1.8.7 version with Unicorn to facilitate an upgrade to Rails 2.3.10, and am running into some issues. Should I uninstall the older versions of these gems? I, [2011-02-02T22:06:16.328076 #30672] INFO -- : listening on addr=0.0.0.0:8080 fd=3 I, [2011-02-02T22:06:16.333137 #30672] INFO -- : Refreshing Gem list /srv/ree/bin/unicorn_rails must be run inside RAILS_ROOT: #<Gem::LoadError: can't activate rack (~> 1.1.0, runtime) for ["actionpack-2.3.10", "rails-2.3.10"], already activated rack-1.2.1 for ["unicorn-3.3.1"]> I, [2011-02-02T22:07:12.259436 #30701] INFO -- : listening on addr=0.0.0.0:8080 fd=3 I, [2011-02-02T22:07:12.259952 #30701] INFO -- : Refreshing Gem list /srv/ree/bin/unicorn_rails must be run inside RAILS_ROOT: #<Gem::LoadError: can't activate rack (~> 1.1.0, runtime) for ["actionpack-2.3.10", "rails-2.3.10"], already activated rack-1.2.1 for ["unicorn-3.3.1"]> I, [2011-02-02T22:09:27.787177 #30772] INFO -- : listening on addr=0.0.0.0:8080 fd=3 I, [2011-02-02T22:09:27.787691 #30772] INFO -- : Refreshing Gem list /srv/ree/bin/unicorn_rails must be run inside RAILS_ROOT: #<Gem::LoadError: can't activate rack (~> 1.1.0, runtime) for ["actionpack-2.3.10", "rails-2.3.10"], already activated rack-1.2.1 for ["unicorn-3.3.1"]> I, [2011-02-02T22:10:44.175407 #30846] INFO -- : listening on addr=0.0.0.0:8080 fd=3 I, [2011-02-02T22:10:44.175928 #30846] INFO -- : Refreshing Gem list /srv/ree/bin/unicorn_rails must be run inside RAILS_ROOT: #<Gem::LoadError: can't activate rack (~> 1.1.0, runtime) for ["actionpack-2.3.10", "rails-2.3.10"], already activated rack-1.2.1 for ["unicorn-3.3.1"]>

  Read the article

• Upload Certificate and Key to RUEI in order to decrypt SSL traffic

  - by stefan.thieme(at)oracle.com

  So you want to monitor encrypted traffic with your RUEI collector ?Actually this is an easy thing if you follow the lines below...I will start out with creating a pair of snakeoil (so called self-signed) certificate and key with the make-ssl-cert tool which comes pre-packaged with apache only for the purpose of this example.$ sudo make-ssl-cert generate-default-snakeoil$ sudo ls -l /etc/ssl/certs/ssl-cert-snakeoil.pem /etc/ssl/private/ssl-cert-snakeoil.key-rw-r--r-- 1 root root     615 2010-06-07 10:03 /etc/ssl/certs/ssl-cert-snakeoil.pem-rw-r----- 1 root ssl-cert 891 2010-06-07 10:03 /etc/ssl/private/ssl-cert-snakeoil.keyRUEI Configuration of Security SSL Keys You will most likely get these two files from your Certificate Authority (CA) and/or your system administrators should be able to extract this from your WebServer or LoadBalancer handling SSL encryption for your infrastructure.Now let's look at the content of these two files, the certificate (apache assumes this is in PEM format) is called a public key and the private key is used by the apache server to encrypt traffic for a client using the certificate to initiate the SSL connection with the server.In case you already know that these two match, you simply have to paste them in one text file and upload this text file to your RUEI instance.$ sudo cat /etc/ssl/certs/ssl-cert-snakeoil.pem /etc/ssl/private/ssl-cert-snakeoil.key > /tmp/ruei.cert_and_key$ sudo cat /tmp/ruei.cert_and_key -----BEGIN CERTIFICATE----- MIIBmTCCAQICCQD7O3XXwVilWzANBgkqhkiG9w0BAQUFADARMQ8wDQYDVQQDEwZ1 YnVudHUwHhcNMTAwNjA3MDgwMzUzWhcNMjAwNjA0MDgwMzUzWjARMQ8wDQYDVQQD EwZ1YnVudHUwgZ8wDQYJKoZIhvcNAQEBBQADgY0AMIGJAoGBALbs+JnI+p+K7Iqa SQZdnYBxOpdRH0/9jt1QKvmH68v81h9+f1Z2rVR7Zrd/l+ruE3H9VvuzxMlKuMH7 qBX/gmjDZTlj9WJM+zc0tSk+e2udy9he20lGzTxv0vaykJkuKcvSWNk4WE9NuAdg IHZvjKgoTSVmvM1ApMCg69nyOy97AgMBAAEwDQYJKoZIhvcNAQEFBQADgYEAk2rv VEkxR1qPSpJiudDuGUHtWKBKWiWbmSwI3REZT+0vG+YDG5a55NdxgRk3zhQntqF7 gNYjKxblBByBpY7W0ci00kf7kFgvXWMeU96NSQJdnid/YxzQYn0dGL2rSh1dwdPN NPQlNSfnEQ1yxFevR7aRdCqTbTXU3mxi8YaSscE= -----END CERTIFICATE----- -----BEGIN RSA PRIVATE KEY----- MIICXgIBAAKBgQC27PiZyPqfiuyKmkkGXZ2AcTqXUR9P/Y7dUCr5h+vL/NYffn9W dq1Ue2a3f5fq7hNx/Vb7s8TJSrjB+6gV/4Jow2U5Y/ViTPs3NLUpPntrncvYXttJ Rs08b9L2spCZLinL0ljZOFhPTbgHYCB2b4yoKE0lZrzNQKTAoOvZ8jsvewIDAQAB AoGBAJ7LCWeeUwnKNFqBYmD3RTFpmX4furnal3lBDX0945BZtJr0WZ/6N679zIYA aiVTdGfgjvDC9lHy3n3uctRd0Jqdh2QoSSxNBhq5elIApNIIYzu7w/XI/VhGcDlA b6uadURQEC2q+M8YYjw3mwR2omhCWlHIViOHe/9T8jfP/8pxAkEA7k39WRcQildH DFKcj7gurqlkElHysacMTFWf0ZDTEUS6bdkmNXwK6mH63BlmGLrYAP5AMgKgeDf8 D+WRfv8YKQJBAMSCQ7UGDN3ysyfIIrdc1RBEAk4BOrKHKtD5Ux0z5lcQkaCYrK8J DuSldreN2yOhS99/S4CRWmGkTj04wRSnjwMCQQCaR5mW3QzTU4/m1XEQxsBKSdZE 2hMSmsCmhuSyK13Kl0FPLr/C7qyuc4KSjksABa8kbXaoKfUz/6LLs+ePXZ2JAkAv +mIPk5+WnQgS4XFgdYDrzL8HTpOHPSs+BHG/goltnnT/0ebvgXWqa5+1pyPm6h29 PrYveM2pY1Va6z1xDowDAkEAttfzAwAHz+FUhWQCmOBpvBuW/KhYWKZTMpvxFMSY YD5PH6NNyLfBx0J4nGPN5n/f6il0s9pzt3ko++/eUtWSnQ== -----END RSA PRIVATE KEY----- Simply click on the add new key and browse for the cert_and_key file on your desktop which you concatenated earlier using any text editor. You may need to add a passphrase in order to decrypt the RSA key in some cases (it should tell you BEGIN ENCRYPTED PRIVATE KEY in the header line). I will show you the success screen after uploading the certificate to RUEI. You may want to restart your collector once you have uploaded all the certificate/key pairs you want to use in order to make sure they get picked up asap.You should be able to see the number of SSL Connections rising in the Collector statistics screen below. The figures for decrypt errors should slowly go down and the usage figures for your encryption algortihm on the subsequent SSL Encryption screen should go up. You should be 100% sure everything works fine by now, otherwise see below to distinguish the remaining 1% from your 99% certainty.Verify Certificate and Key are matchingYou can compare the modulus of private key and public certificate and they should match in order for the key to fit the lock. You only want to make sure they both fit each other.We are actually interested only in the following details of the two files, which can be determined by using the -subject, -dates and -modulus command line switches instead of the complete -text output of the x509 certificate/rsa key contents.$ sudo openssl x509 -noout -subject -in /etc/ssl/certs/ssl-cert-snakeoil.pemsubject= /CN=ubuntu$ sudo openssl x509 -noout -dates -in /etc/ssl/certs/ssl-cert-snakeoil.pemnotBefore=Jun  7 08:03:53 2010 GMTnotAfter=Jun  4 08:03:53 2020 GMT$ sudo openssl x509 -noout -modulus -in /etc/ssl/certs/ssl-cert-snakeoil.pem Modulus=B6ECF899C8FA9F8AEC8A9A49065D9D80713A97511F4FFD8EDD502AF987EBCBFCD61F7E7F5676AD547B66B77F97EAEE1371FD56FBB3C4C94AB8C1FBA815FF8268C3653963F5624CFB3734B5293E7B6B9DCBD85EDB4946CD3C6FD2F6B290992E29CBD258D938584F4DB8076020766F8CA8284D2566BCCD40A4C0A0EBD9F23B2F7B $ sudo openssl rsa -noout -modulus -in /etc/ssl/private/ssl-cert-snakeoil.keyModulus=B6ECF899C8FA9F8AEC8A9A49065D9D80713A97511F4FFD8EDD502AF987EBCBFCD61F7E7F5676AD547B66B77F97EAEE1371FD56FBB3C4C94AB8C1FBA815FF8268C3653963F5624CFB3734B5293E7B6B9DCBD85EDB4946CD3C6FD2F6B290992E29CBD258D938584F4DB8076020766F8CA8284D2566BCCD40A4C0A0EBD9F23B2F7BAs you can see the modulus matches exactly and we have the proof that the certificate has been created using the private key. OpenSSL Certificate and Key DetailsAs I already told you, you do not need all the greedy details, but in case you want to know it in depth what is actually in those hex-blocks can be made visible with the following commands which show you the actual content in a human readable format.Note: You may not want to post all the details of your private key =^) I told you I have been using a self-signed certificate only for showing you these details.$ sudo openssl rsa -noout -text -in /etc/ssl/private/ssl-cert-snakeoil.keyPrivate-Key: (1024 bit)modulus:    00:b6:ec:f8:99:c8:fa:9f:8a:ec:8a:9a:49:06:5d:    9d:80:71:3a:97:51:1f:4f:fd:8e:dd:50:2a:f9:87:    eb:cb:fc:d6:1f:7e:7f:56:76:ad:54:7b:66:b7:7f:    97:ea:ee:13:71:fd:56:fb:b3:c4:c9:4a:b8:c1:fb:    a8:15:ff:82:68:c3:65:39:63:f5:62:4c:fb:37:34:    b5:29:3e:7b:6b:9d:cb:d8:5e:db:49:46:cd:3c:6f:    d2:f6:b2:90:99:2e:29:cb:d2:58:d9:38:58:4f:4d:    b8:07:60:20:76:6f:8c:a8:28:4d:25:66:bc:cd:40:    a4:c0:a0:eb:d9:f2:3b:2f:7bpublicExponent: 65537 (0x10001)privateExponent:    00:9e:cb:09:67:9e:53:09:ca:34:5a:81:62:60:f7:    45:31:69:99:7e:1f:ba:b9:da:97:79:41:0d:7d:3d:    e3:90:59:b4:9a:f4:59:9f:fa:37:ae:fd:cc:86:00:    6a:25:53:74:67:e0:8e:f0:c2:f6:51:f2:de:7d:ee:    72:d4:5d:d0:9a:9d:87:64:28:49:2c:4d:06:1a:b9:    7a:52:00:a4:d2:08:63:3b:bb:c3:f5:c8:fd:58:46:    70:39:40:6f:ab:9a:75:44:50:10:2d:aa:f8:cf:18:    62:3c:37:9b:04:76:a2:68:42:5a:51:c8:56:23:87:    7b:ff:53:f2:37:cf:ff:ca:71prime1:    00:ee:4d:fd:59:17:10:8a:57:47:0c:52:9c:8f:b8:    2e:ae:a9:64:12:51:f2:b1:a7:0c:4c:55:9f:d1:90:    d3:11:44:ba:6d:d9:26:35:7c:0a:ea:61:fa:dc:19:    66:18:ba:d8:00:fe:40:32:02:a0:78:37:fc:0f:e5:    91:7e:ff:18:29prime2:    00:c4:82:43:b5:06:0c:dd:f2:b3:27:c8:22:b7:5c:    d5:10:44:02:4e:01:3a:b2:87:2a:d0:f9:53:1d:33:    e6:57:10:91:a0:98:ac:af:09:0e:e4:a5:76:b7:8d:    db:23:a1:4b:df:7f:4b:80:91:5a:61:a4:4e:3d:38:    c1:14:a7:8f:03exponent1:    00:9a:47:99:96:dd:0c:d3:53:8f:e6:d5:71:10:c6:    c0:4a:49:d6:44:da:13:12:9a:c0:a6:86:e4:b2:2b:    5d:ca:97:41:4f:2e:bf:c2:ee:ac:ae:73:82:92:8e:    4b:00:05:af:24:6d:76:a8:29:f5:33:ff:a2:cb:b3:    e7:8f:5d:9d:89exponent2:    2f:fa:62:0f:93:9f:96:9d:08:12:e1:71:60:75:80:    eb:cc:bf:07:4e:93:87:3d:2b:3e:04:71:bf:82:89:    6d:9e:74:ff:d1:e6:ef:81:75:aa:6b:9f:b5:a7:23:    e6:ea:1d:bd:3e:b6:2f:78:cd:a9:63:55:5a:eb:3d:    71:0e:8c:03coefficient:    00:b6:d7:f3:03:00:07:cf:e1:54:85:64:02:98:e0:    69:bc:1b:96:fc:a8:58:58:a6:53:32:9b:f1:14:c4:    98:60:3e:4f:1f:a3:4d:c8:b7:c1:c7:42:78:9c:63:    cd:e6:7f:df:ea:29:74:b3:da:73:b7:79:28:fb:ef:    de:52:d5:92:9d$ sudo openssl x509 -noout -text -in /etc/ssl/certs/ssl-cert-snakeoil.pemCertificate:    Data:        Version: 1 (0x0)        Serial Number:            fb:3b:75:d7:c1:58:a5:5b        Signature Algorithm: sha1WithRSAEncryption        Issuer: CN=ubuntu        Validity            Not Before: Jun  7 08:03:53 2010 GMT            Not After : Jun  4 08:03:53 2020 GMT        Subject: CN=ubuntu        Subject Public Key Info:            Public Key Algorithm: rsaEncryption            RSA Public Key: (1024 bit)                Modulus (1024 bit):                    00:b6:ec:f8:99:c8:fa:9f:8a:ec:8a:9a:49:06:5d:                    9d:80:71:3a:97:51:1f:4f:fd:8e:dd:50:2a:f9:87:                    eb:cb:fc:d6:1f:7e:7f:56:76:ad:54:7b:66:b7:7f:                    97:ea:ee:13:71:fd:56:fb:b3:c4:c9:4a:b8:c1:fb:                    a8:15:ff:82:68:c3:65:39:63:f5:62:4c:fb:37:34:                    b5:29:3e:7b:6b:9d:cb:d8:5e:db:49:46:cd:3c:6f:                    d2:f6:b2:90:99:2e:29:cb:d2:58:d9:38:58:4f:4d:                    b8:07:60:20:76:6f:8c:a8:28:4d:25:66:bc:cd:40:                    a4:c0:a0:eb:d9:f2:3b:2f:7b                Exponent: 65537 (0x10001)    Signature Algorithm: sha1WithRSAEncryption        93:6a:ef:54:49:31:47:5a:8f:4a:92:62:b9:d0:ee:19:41:ed:        58:a0:4a:5a:25:9b:99:2c:08:dd:11:19:4f:ed:2f:1b:e6:03:        1b:96:b9:e4:d7:71:81:19:37:ce:14:27:b6:a1:7b:80:d6:23:        2b:16:e5:04:1c:81:a5:8e:d6:d1:c8:b4:d2:47:fb:90:58:2f:        5d:63:1e:53:de:8d:49:02:5d:9e:27:7f:63:1c:d0:62:7d:1d:        18:bd:ab:4a:1d:5d:c1:d3:cd:34:f4:25:35:27:e7:11:0d:72:        c4:57:af:47:b6:91:74:2a:93:6d:35:d4:de:6c:62:f1:86:92:        b1:c1The above output can also be seen if you direct your browser client to your website and check the certificate sent by the server to your browser. You will be able to lookup all the details including the validity dates, subject common name and the public key modulus.Capture an SSL connection using WiresharkAnd as you would have expected, looking at the low-level tcp data that has been exchanged between the client and server with a tcp-diagnostics tool (i.e. wireshark/tcpdump) you can also see the modulus in there.These were the settings I used to capture all traffic on the local loopback interface, matching the filter expression: tcp and ip and host 127.0.0.1 and port 443. This tells Wireshark to leave out any other information, I may not have been interested in showing you.

  Read the article

• Examining C/C++ Heap memory statistics in gdb

  - by fd

  I'm trying to investigate the state of the C/C++ heap from within gdb on Linux amd64, is there a nice way to do this? One approach I've tried is to "call mallinfo()" but unfortunately I can't then extract the values I want since gdb deal with the return value properly. I'm not easily able to write a function to be compiled into the binary for the process I am attached to, so I can simply implement my own function to extract the values by calling mallinfo() in my own code this way. Is there perhaps a clever trick that will allow me to do this on-the-fly? Another option could be to locate the heap and traverse the malloc headers / free list; I'd appreciate any pointers to where I could start in finding the location and layout of these. I've been trying to Google and read around the problem for about 2 hours and I've learnt some fascinating stuff but still not found what I need.

  Read the article

• String Index Out Of Bound Exception error

  - by Fd Fehfhd

  Im not really sure why a am getting this error. But here is my code it is meant to test palindromes disregarding punctuation. So here is my code import java.util.Scanner; public class PalindromeTester { public static void main(String [] args) { Scanner kb = new Scanner(System.in); String txt = ""; int left; int right; int cntr = 0; do { System.out.println("Enter a word, phrase, or sentence (blank line to stop):"); txt = kb.nextLine(); txt = txt.toLowerCase(); char yP; String noP = ""; for (int i = 0; i < txt.length(); i++) { yP = txt.charAt(i); if (Character.isLetterOrDigit(txt.charAt(yP))) { noP += yP; } } txt = noP; left = 0; right = txt.length() -1; while (txt.charAt(left) == txt.charAt(right) && right > left) { left++; right--; } if (left > right) { System.out.println("Palindrome"); cntr++; } else { System.out.println("Not a palindrome"); } } while (!txt.equals("")); System.out.println("You found " + cntr + " palindromes. Thank you for using palindromeTester."); } } And if i test it and then i put enter so it will tell me how many palindromes you found the error i am getting is javav.lang.StringIndexOutOfBoundException : String index out of range 0 at PalindromeTester.main(PalindromeTester.java:38) and line 28 is while (txt.charAt(left) == txt.charAt(right) && right > left) Thanks for the help in advance

  Read the article

• How do I install a driver for an Atheros AR9285?

  - by Fernando

  How to install the driver for Atheros AR9285 in Ubuntu 11.10. Still no package for 11.10 according to this https://help.ubuntu.com/community/WifiDocs/Device/Atheros/AR9285 Here is the output of the commands marc@fer-VPCYA1V9E:~$ sudo lshw -class network *-network DISABLED description: Wireless interface product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 01 serial: 4c:0f:6e:d6:65:cc width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=ath9k driverversion=3.0.0-12-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:16 memory:d3400000-d340ffff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: 54:42:49:a2:1f:bc capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:43 memory:d2400000-d243ffff ioport:1000(size=128) And the second command marc@fer-VPCYA1V9E:~$ rfkill list 0: sony-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: sony-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no 3: hci0: Bluetooth Soft blocked: no Hard blocked: no 4: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no Is there a way to make it work?

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• How do I connect my NetXtreme BCM5755M Gigabit Ethernet PCI Express in y Dell latitude d630?

  - by Stanton.Sculpture

  Trying to get my 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02) working with my wifi. I just installed Raring Ringtail on this dell latitude D630 and I can't get it to connect without a wifi dongle. This is what I got when I typed sudo lshw -c network: *-network description: Ethernet interface product: NetXtreme BCM5755M Gigabit Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 02 serial: 00:21:70:98:04:32 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.128 firmware=5755m-v3.29 latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:fe8f0000-fe8fffff *-network description: Wireless interface physical id: 2 bus info: usb@2:1 logical name: wlan0 serial: 7c:dd:90:11:a0:10 capabilities: ethernet physical wireless configuration: broadcast=yes driver=rt2800usb driverversion=3.8.0-31-generic firmware=0.29 ip=10.0.0.8 link=yes multicast=yes wireless=IEEE 802.11bgn Also, when I go to additional drivers in the software and updates settings, no proprietary drivers show up. I've tried sudo apt-get install b43-fwcutter firmware-b43-installer because it worked on a bunch of old Dell laptops that I converted over before, but it didn't work on this one. Is this driver even compatible with wifi? Please help.

  Read the article

• wireless detected but Can't connect to network, Wifi card intel pro wireless N100 BGN

  - by Alexandre777

  Thanks in advance, I installed Linux Mint kernel 3.0.0-12 x64 ,wireless is detected and I configure it in network manager but can't coonect, there are the results of command line: $ iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ sudo lshw -C network** *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:51:c9:d6 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:48 memory:d7400000-d7401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:06:00.0 logical name: eth0 version: c0 serial: 48:5b:39:99:8f:16 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.2 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:51 memory:d3800000-d383ffff ioport:8000(size=128 $ rfkill list all 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Thank you.

  Read the article

• Cannot make Wi-Fi hotspot

  - by Junaid

  I want to make my laptop as wi-fi hotspot. To do so, I pressed button Settings-Network-Wireless-Use as Hotspot.. Then it creates a wireless network connection 'Hostspot' and connects. But it gets disconnected just after making connection. Here is my network hardware info: sudo lshw -C network *-network description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:d9200000-d9201fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=N/A ip=192.168.1.4 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:45 ioport:2000(size=256) memory:d5010000-d5010fff memory:d5000000-d500ffff memory:d5020000-d502ffff My machine is running on Ubuntu 11.10 Can anybody help in it? Thanks

  Read the article

• Gnome-Network-Manager Config File Migration

  - by Jorge

  I think I have an issue with gnome-network-manager, I used to have a lot of connections configured, Wireless, Wired and VPN. After upgrading to 12.04 (from 11.10) I lost every configuration. I realized that the configs that used to be saved in $HOME/.gconf/system/networking/connections now are being saved in /etc/NetworkManager/system-connections/. I don't know how to migrate my settings to the new config file format Can anybody help me? jorge@thinky:~$ sudo lshw -C network *-network description: Ethernet interface product: 82566MM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:1f:e2:14:5a:9b capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=1.5.1-k firmware=0.3-0 latency=0 link=no multicast=yes port=twisted pair resources: irq:46 memory:fe000000-fe01ffff memory:fe025000-fe025fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 4965 AG or AGN [Kedron] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 61 serial: 00:21:5c:32:c2:e5 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwl4965 driverversion=3.2.0-23-generic-pae firmware=228.61.2.24 ip=192.168.2.103 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:47 memory:df3fe000-df3fffff jorge@thinky:~$ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04 LTS Release: 12.04 Codename: precise jorge@thinky:~$ uname -a Linux thinky 3.2.0-23-generic-pae #36-Ubuntu SMP Tue Apr 10 22:19:09 UTC 2012 i686 i686 i386 GNU/Linux jorge@thinky:~$ dpkg -l | grep -i firm ii linux-firmware 1.79 Firmware for Linux kernel drivers

  Read the article

• Missing Wireless access point

  - by nvcnvn

  I have an: Ubuntu 12.04 with proprietary Boardcom STA Wireless driver installed BCM43224 802.11a/b/g/n wireless card TP-LINK TD-W8101G 54Mbps Wireless ADSL2+ Modem Router Yesterday before I went to sleep, I still connect to my wireless access point, this morning when I start my laptop I don't see it in the list - there are some neighbors listed but not mine. The WLAN is green, with my old Nokia E72, I still see my access point with 100% signal. I have tried to restart my laptop and turn the firmware off/on by the switch but no help. I have read the WirelessTroubleShootingGuide but I can do anything. Here is some of my card info: *-network description: Wireless interface product: BCM43224 802.11a/b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: c0:cb:38:06:5d:53 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11abgn resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: 03 serial: f0:4d:a2:42:ab:e4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168d-1.fw ip=192.168.1.3 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:42 ioport:5000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff memory:f0420000-f043ffff

  Read the article

• format/build raid 5 with one 4k drive, three 512b

  - by skidawgz

  I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

  Read the article

• two possible wifi devices competing, one is hard blocked - unable to connect wireless

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff contents of /var/lib/NetworkManager/NetworkManager.state [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• two possible wifi devices competing, one is hard blocked

  - by patrickmw

  blacklisted acer_wmi because that was showing up in the rfkill list then ideapad_wlan was listed $ rfkill list wifi 1: ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 3: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes $ lshw -C network *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Atheros Communications physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: c0 serial: f0:de:f1:12:21:e9 size: 1Gbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI duplex=full firmware=N/A ip=192.168.1.139 latency=0 link=yes multicast=yes port=twisted pair speed=1Gbit/s resources: irq:42 memory:f0400000-f043ffff ioport:2000(size=128) *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: ac:81:12:38:ba:89 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff I'm not sure how to disable the wifi devices independently. I'm also not sure which device is the correct one. I think its the brcmw device. Any suggestions?

  Read the article

• Can't get Wireless to work! (Fujitsu siemens ESPRIMO Mobile u9200) Ubuntu 12.4

  - by Martin Oscarsson

  I can't get wireless to work on my computer. I have recently installed 12.04. Computer name: (Fujitsu siemens ESPRIMO Mobile u9200) Hardware button starts bluetooth - so can't start that way. Have searched the Internet for help but can't find any on my specific problem! State: connected (global) - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: ath5k State: disconnected Default: no *-network beskrivning: Trådlöst gränssnitt produkt: AR242x / AR542x Wireless Network Adapter (PCI-Express) tillverkare: Atheros Communications Inc. *-network beskrivning: Ethernet interface produkt: 88E8055 PCI-E Gigabit Ethernet Controller tillverkare: Marvell Technology Group Ltd. HERE IS ALL THE NETWORK INFO: ellika@ellikas:~$ ifconfig eth0 Link encap:Ethernet HWaddr 00:1e:33:00:96:9a inet addr:192.168.1.26 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe00:969a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13778 errors:0 dropped:0 overruns:0 frame:0 TX packets:9510 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14022669 (14.0 MB) TX bytes:1001621 (1.0 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1542 errors:0 dropped:0 overruns:0 frame:0 TX packets:1542 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:125040 (125.0 KB) TX bytes:125040 (125.0 KB) ellika@ellikas:~$ sudo ifconfig [sudo] password for ellika: eth0 Link encap:Ethernet HWaddr 00:1e:33:00:96:9a inet addr:192.168.1.26 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe00:969a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:13801 errors:0 dropped:0 overruns:0 frame:0 TX packets:9528 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14024965 (14.0 MB) TX bytes:1002836 (1.0 MB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1542 errors:0 dropped:0 overruns:0 frame:0 TX packets:1542 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:125040 (125.0 KB) TX bytes:125040 (125.0 KB) ellika@ellikas:~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operationen inte möjlig p.g.a. RF-kill ellika@ellikas:~$ phy0 Wireless LAN phy0: command not found ellika@ellikas:~$ rfkill Usage: rfkill [options] command Options: --version show version (0.4-1ubuntu2 (Ubuntu)) Commands: help event list [IDENTIFIER] block IDENTIFIER unblock IDENTIFIER where IDENTIFIER is the index no. of an rfkill switch or one of: <idx> all wifi wlan bluetooth uwb ultrawideband wimax wwan gps fm ellika@ellikas:~$ sudo rf-kill unblock all sudo: rf-kill: kommandot hittades inte ellika@ellikas:~$ sudo rfkill unblock all ellika@ellikas:~$ sedan sudo ifconfig wlan0 sedan: command not found ellika@ellikas:~$ sudo ifconfig wlan0 wlan0 Link encap:Ethernet HWaddr 00:22:5f:3f:63:76 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ellika@ellikas:~$ ^C ellika@ellikas:~$ ^C ellika@ellikas:~$ sudo rfkill unblock all ellika@ellikas:~$ sudo ifconfig wlan0 up SIOCSIFFLAGS: Operationen inte möjlig p.g.a. RF-kill ellika@ellikas:~$ sudo rfkill unblock all ellika@ellikas:~$ sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes ellika@ellikas:~$ sudo rfkill unblock all ellika@ellikas:~$ echo -e "sudo lshw --class network:\n\n$(sudo lshw -c network)\n\nlspci -nnn | grep Ethernet:\n\n$(lspci -nnn | grep Ethernet)\n\nlsusb:\n\n$(lsusb)\n\niwlist wlan0 scanning:\n\n$(iwlist wlan0 scanning)\n\nrfkill list:\n\n$(rfkill list)\n\nping -c 5 google.com:\n\n$(ping -c 5 google.com)\n\nhost google.com 8.8.8.8:\n\n$(host google.com 8.8.8.8)\n\nlsb_release -a:\n\n$(lsb_release -a)\n\nuname -a:\n\n$(uname -a)" ^[[C^[[C^[[C^[[C^[[C^[[B wlan0 Failed to read scan data : Network is down No LSB modules are available. sudo lshw --class network: *-network beskrivning: Ethernet interface produkt: 88E8055 PCI-E Gigabit Ethernet Controller tillverkare: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 logiskt namn: eth0 version: 14 serienummer: 00:1e:33:00:96:9a storlek: 100Mbit/s kapacitet: 1Gbit/s bredd: 64 bits klocka: 33MHz förmågor: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation konfiguration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.26 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resurser: irq:44 memory:f8000000-f8003fff ioport:3000(storlek=256) memory:f2000000-f201ffff *-network INAKTIVERAD beskrivning: Trådlöst gränssnitt produkt: AR242x / AR542x Wireless Network Adapter (PCI-Express) tillverkare: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logiskt namn: wlan0 version: 04 serienummer: 00:22:5f:3f:63:76 bredd: 64 bits klocka: 33MHz förmågor: pm msi pciexpress msix bus_master cap_list ethernet physical wireless konfiguration: broadcast=yes driver=ath5k driverversion=3.2.0-30-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bg resurser: irq:18 memory:fa000000-fa00ffff lspci -nnn | grep Ethernet: 04:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller [11ab:4363] (rev 14) 06:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 04) lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 05e3:0715 Genesys Logic, Inc. USB 2.0 microSD Reader Bus 001 Device 003: ID 05c8:0103 Cheng Uei Precision Industry Co., Ltd (Foxlink) FO13FF-65 PC-CAM iwlist wlan0 scanning: rfkill list: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes ping -c 5 google.com: PING google.com (173.194.32.34) 56(84) bytes of data. 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=1 ttl=55 time=10.6 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=2 ttl=55 time=10.5 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=3 ttl=55 time=10.4 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=4 ttl=55 time=10.4 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=5 ttl=55 time=10.4 ms --- google.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4004ms rtt min/avg/max/mdev = 10.451/10.517/10.631/0.062 ms host google.com 8.8.8.8: Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: google.com has address 173.194.32.36 google.com has address 173.194.32.38 google.com has address 173.194.32.41 google.com has address 173.194.32.37 google.com has address 173.194.32.35 google.com has address 173.194.32.39 google.com has address 173.194.32.33 google.com has address 173.194.32.34 google.com has address 173.194.32.46 google.com has address 173.194.32.32 google.com has address 173.194.32.40 google.com has IPv6 address 2a00:1450:400f:801::100e google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. lsb_release -a: Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise uname -a: Linux ellikas 3.2.0-30-generic-pae #48-Ubuntu SMP Fri Aug 24 17:14:09 UTC 2012 i686 i686 i386 GNU/Linux ellika@ellikas:~$ ellika@ellikas:~$ clear ellika@ellikas:~$ echo -e "sudo lshw --class network:\n\n$(sudo lshw -c network)\n\nlspci -nnn | grep Ethernet:\n\n$(lspci -nnn | grep Ethernet)\n\nlsusb:\n\n$(lsusb)\n\niwlist wlan0 scanning:\n\n$(iwlist wlan0 scanning)\n\nrfkill list:\n\n$(rfkill list)\n\nping -c 5 google.com:\n\n$(ping -c 5 google.com)\n\nhost google.com 8.8.8.8:\n\n$(host google.com 8.8.8.8)\n\nlsb_release -a:\n\n$(lsb_release -a)\n\nuname -a:\n\n$(uname -a)" wlan0 Failed to read scan data : Network is down No LSB modules are available. sudo lshw --class network: *-network beskrivning: Ethernet interface produkt: 88E8055 PCI-E Gigabit Ethernet Controller tillverkare: Marvell Technology Group Ltd. physical id: 0 bus info: pci@0000:04:00.0 logiskt namn: eth0 version: 14 serienummer: 00:1e:33:00:96:9a storlek: 100Mbit/s kapacitet: 1Gbit/s bredd: 64 bits klocka: 33MHz förmågor: pm vpd msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation konfiguration: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full firmware=N/A ip=192.168.1.26 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resurser: irq:44 memory:f8000000-f8003fff ioport:3000(storlek=256) memory:f2000000-f201ffff *-network INAKTIVERAD beskrivning: Trådlöst gränssnitt produkt: AR242x / AR542x Wireless Network Adapter (PCI-Express) tillverkare: Atheros Communications Inc. physical id: 0 bus info: pci@0000:06:00.0 logiskt namn: wlan0 version: 04 serienummer: 00:22:5f:3f:63:76 bredd: 64 bits klocka: 33MHz förmågor: pm msi pciexpress msix bus_master cap_list ethernet physical wireless konfiguration: broadcast=yes driver=ath5k driverversion=3.2.0-30-generic-pae firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bg resurser: irq:18 memory:fa000000-fa00ffff lspci -nnn | grep Ethernet: 04:00.0 Ethernet controller [0200]: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller [11ab:4363] (rev 14) 06:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 04) lsusb: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 05e3:0715 Genesys Logic, Inc. USB 2.0 microSD Reader Bus 001 Device 003: ID 05c8:0103 Cheng Uei Precision Industry Co., Ltd (Foxlink) FO13FF-65 PC-CAM iwlist wlan0 scanning: rfkill list: 0: phy0: Wireless LAN Soft blocked: no Hard blocked: yes ping -c 5 google.com: PING google.com (173.194.32.34) 56(84) bytes of data. 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=1 ttl=55 time=10.6 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=2 ttl=55 time=10.5 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=3 ttl=55 time=10.4 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=4 ttl=55 time=10.4 ms 64 bytes from arn06s02-in-f2.1e100.net (173.194.32.34): icmp_req=5 ttl=55 time=10.5 ms --- google.com ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4004ms rtt min/avg/max/mdev = 10.476/10.522/10.602/0.045 ms host google.com 8.8.8.8: Using domain server: Name: 8.8.8.8 Address: 8.8.8.8#53 Aliases: google.com has address 173.194.32.36 google.com has address 173.194.32.38 google.com has address 173.194.32.41 google.com has address 173.194.32.37 google.com has address 173.194.32.35 google.com has address 173.194.32.39 google.com has address 173.194.32.33 google.com has address 173.194.32.34 google.com has address 173.194.32.46 google.com has address 173.194.32.32 google.com has address 173.194.32.40 google.com has IPv6 address 2a00:1450:400f:801::100e google.com mail is handled by 40 alt3.aspmx.l.google.com. google.com mail is handled by 20 alt1.aspmx.l.google.com. google.com mail is handled by 30 alt2.aspmx.l.google.com. google.com mail is handled by 50 alt4.aspmx.l.google.com. google.com mail is handled by 10 aspmx.l.google.com. lsb_release -a: Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise uname -a: Linux ellikas 3.2.0-30-generic-pae #48-Ubuntu SMP Fri Aug 24 17:14:09 UTC 2012 i686 i686 i386 GNU/Linux

  Read the article

• wifi not working hp dv4

  - by Blaze

  i get this output for sudo lshw -C network : *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:08:00.0 logical name: eth0 version: 06 serial: 3c:4a:92:cd:63:98 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network DISABLED description: Wireless interface product: RT5390 [802.11 b/g/n 1T1R G-band PCI Express Single Chip] vendor: Ralink corp. physical id: 0 bus info: pci@0000:0a:00.0 logical name: wlan0 version: 00 serial: 90:00:4e:82:3c:5b width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.0.0-17-generic-pae firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:17 memory:c2500000-c250ffff i cant enable the wifi using the fn+f12 key.. its just stuck. In windows 7 it gets enabled when i press the same keys. but this happens after it gets booted up... i just want to use the wifi in anyway possible. can anybody help?

  Read the article

• Centrino Wireless-N 1000 takes forever to connect and keeps asking for password

  - by waclock

  A few days ago I started having this problem. When I tried to connect to any WiFi Connection it would stay connecting forever, and after a minute or so it would ask me for the password again. The strange thing is that this happened out of nowhere, I did not install any new drivers or anything like that. After this happened I decided to uninstall ubuntu and install it again ("inside windows") but the problem is still there. Any suggestions would be greatly appreciated. 0: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 2: phy0: Wireless LAN Soft blocked: no Hard blocked: no description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 2c:27:d7:aa:e4:7d size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:50 ioport:4000(size=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:0d:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:09:9c:58 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-23-generic-pae firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:52 memory:c4500000-c4501fff *-network description: Ethernet interface physical id: 1 bus info: usb@2:1.2 logical name: eth1 serial: ee:85:2f:7d:80:96 capabilities: ethernet physical configuration: broadcast=yes driver=ipheth ip=172.20.10.2 link=yes multicast=yes

  Read the article

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• Recover open but deleted file on Linux using ln instead of cp

  - by Yang

  Say I have a file that's downloading (from a source that's hard to re-download from), but accidentally deleted from the filesystem namespace (/tmp/blah), and I'd like to recover this file. Normally I could just cp /proc/$PID/fd/$FD /tmp/blah, but in this case that would only get me a partial snapshot, since the file is still downloading. Furthermore, once the download completes, the downloading process (e.g. Chrome) will close the FD. Any way to recover by inode/create a hard link? Any other solutions? If it makes any difference, I'm mainly concerned with ext4. Thanks in advance.

  Read the article

• Why does 1GBit card have output limited to 80 MiB ?

  - by Gallus

  I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

  Read the article

• Raid Shows Up as Multiple Drives - Can't Mount

  - by manyxcxi

  I have a single hard drive that the OS is installed on and I have Sil raid card installed with two matching 500GB hdds set up in Raid 0 and formatted- they're completely empty. For whatever reason they are showing up as /dev/sdb and /dev/sdc and not as a single hard drive. I used fdisk to format both raid drives as Linux raid auto (fd) but I cannot mount either device and dmraid doesn't seem to want to work, what step am I missing? When I installed 9.04 oh so long ago it seems like it recognized and automatically did everything that needed to be done, now I'm stuck. dmraid Output root@tripoli:~# dmraid -r /dev/sdc: sil, "sil_biaebhadcfcb", stripe, ok, 976771072 sectors, data@ 0 /dev/sdb: sil, "sil_biaebhadcfcb", stripe, ok, 976771072 sectors, data@ 0 root@tripoli:~# dmraid -ay RAID set "sil_biaebhadcfcb" already active fdisk Output root@tripoli:~# fdisk -l Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000b9b01 Device Boot Start End Blocks Id System /dev/sda1 * 1 32 248832 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 32 60802 488134657 5 Extended /dev/sda5 32 60802 488134656 8e Linux LVM Disk /dev/sdb: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x6ead5c9a Device Boot Start End Blocks Id System /dev/sdb1 1 60801 488384001 fd Linux raid autodetect Disk /dev/sdc: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xe6e2af28 Device Boot Start End Blocks Id System /dev/sdc1 1 60801 488384001 fd Linux raid autodetect

  Read the article

• Missing driver ASUS PCE-N53 11n N600 PCI-E Adapter

  - by oyse

  I have problems with getting an Asus PCE-N53 11n N600 PCI-E Adapter card to work on my desktop computer. As far as I can tell no drivers are installed for the card. I know I can manually download the drivers directly from Asus, but I would rather not go that route. If there are anyone that knows about any packages or other things I can do to make this work would be much appreciated. Some systems details: $ lsb_release -a No LSB modules are available. Distributor ID: Ubuntu Description: Ubuntu 12.04.1 LTS Release: 12.04 Codename: precise $ sudo lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: d4:3d:7e:03:b9:1d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=192.168.0.173 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:d000(size=256) memory:f2104000-f2104fff memory:f2100000-f2103fff *-network UNCLAIMED description: Network controller product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:04:00.0 version: 00 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f7100000-f710ffff $ lsmod Module Size Used by nvidia 12319264 51 vesafb 13844 1 snd_hda_codec_hdmi 32474 1 joydev 17693 0 bnep 18281 2 rfcomm 47604 0 bluetooth 180104 10 bnep,rfcomm snd_hda_codec_realtek 224173 1 snd_seq_midi 13324 0 ppdev 17113 0 snd_rawmidi 30748 1 snd_seq_midi usbhid 47199 0 hid 99559 1 usbhid nouveau 774641 0 parport_pc 32866 1 snd_hda_intel 33773 5 ttm 76949 1 nouveau snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel drm_kms_helper 46978 1 nouveau drm 242038 3 nouveau,ttm,drm_kms_helper snd_seq_midi_event 14899 1 snd_seq_midi snd_hwdep 13668 1 snd_hda_codec snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event i2c_algo_bit 13423 1 nouveau mxm_wmi 12979 1 nouveau wmi 19256 1 mxm_wmi mac_hid 13253 0 snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec psmouse 97362 0 video 19596 1 nouveau snd_timer 29990 2 snd_seq,snd_pcm snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq snd 78855 20 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_rawmidi,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_seq,snd_pcm,snd_timer,snd_seq_device serio_raw 13211 0 soundcore 15091 1 snd snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 lp 17799 0 parport 46562 3 ppdev,parport_pc,lp r8169 62099 0

  Read the article

• Wireless doesn't work after installing 11.10

  - by Ingram

  I just did a fresh install of 11.10 32 bit and I can't get my wireless to work. I installed the drivers the Broadcom STA wireless drivers through additional drivers and rebooted, but it still doesn't see any wireless networks Did something change in 11.10 that makes the wireless card not work anymore? I was using 10.10 before, and it worked fine. Do I need to go back to 10.10? sudo lshw -C network [sudo] password for user1: *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 10 serial: 00:1f:16:be:55:ff size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 duplex=full firmware=sb v2.19 ip=192.168.0.70 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:43 memory:f0300000-f030ffff *-network UNCLAIMED description: Network controller product: BCM4311 802.11b/g WLAN vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:09:00.0 version: 01 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0400000-f0403fff

  Read the article

• Trendnet tew-424ub wireless not working after update 12.10

  - by dwa

  I updated packages from the software manager and now my wireless won't work. It's a Trendnet tew-424ub iwconfig says lo no wireless extensions. eth0 no wireless extensions. sudo lshw -C network: description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 02 serial: 1c:6f:65:46:e9:d4 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full ip=192.168.1.137 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:de00(size=256) memory:fdaff000-fdafffff memory:fdae0000-fdaeffff memory:fda00000-fda0ffff lsusb: Bus 003 Device 002: ID 0bc2:3332 Seagate RSS LLC Expansion Bus 003 Device 003: ID 05e3:0605 Genesys Logic, Inc. USB 2.0 Hub [ednet] Bus 003 Device 006: ID 0457:0163 Silicon Integrated Systems Corp. 802.11 Wireless LAN Adapter Bus 005 Device 002: ID 046d:c00c Logitech, Inc. Optical Wheel Mouse Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 009 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 005: ID 0781:5530 SanDisk Corp. Cruzer Bus 010 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Help? I'm not sure where to start. I've been browsing forums and such for a long time and nothing I try is working.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >