Search Results

Search found 17018 results on 681 pages for 'floppy disk drive'.

Page 5/681 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• Retrieving virtual disk file name from disk number

  - by Josip Medved

  When I list virtual disks within diskpart: DISKPART> list vdisk VDisk ### Disk ### State Type File --------- -------- -------------------- --------- ---- VDisk 0 Disk 2 Attached not open Fixed C:\Disk.vhd Interesting part for me here is file name. I tried to find equivalent of function that would give me file name (under File column) if I know disk number. Any idea which function that might be?

  Read the article

• Booting from a USB drive that was originally a boot drive

  - by daveh551

  When Win 7 went RTM, I upgraded my laptop from XP. But to protect myself against the possibility of having data inaccessible, I got a new disk and put it in the laptop, and took the old (XP) disk and put it in a USB enclosure. I have no trouble accessing the data on the USB drive under Windows 7. But I would like to be able to plug it in, tell the BIOS to boot from the USB drive, and be back on my old machine. The laptop is a Dell Precision M90, and it has a boot from USB option in its boot menu. But when I try to do that, it does read the drive, gets as far as putting up the Windows XP splash screen and starting the boot progress bar, and then reboots. What do I need to do to the old disk now running on USB to allow the machine to boot from it?

  Read the article

• drive life time

  - by Remus Rigo

  hi all can anyone tell me or send me a ink about the lifetime of drives (floppy,hard disk, CD, DVD, flash...) thanks

  Read the article

• Cloning a USB flash drive to another larger one, is it safe to do so?

  - by Rob Kam

  I used Acronis True Image Home 2010 to clone a Dane-Elec zLight 8Gb pen drive/USB flash drive to a PNY Attaché 16Gb USB flash drive. Now WinXP shows the drive in device manager as USB DISK 2.0 USB DEVICE but doesn't have it in My Computer/doesn't assign it a drive letter. What is it that has messed up the PNY Attaché and is there some way to repair it so that it can be used as a regular USB flash drive again? Is there a safe way to clone a USB flash drive to another larger one? How safe is it to backup and restore a USB flash drive to/from a drive-image?

  Read the article

• USB drive is empty in drive management

  - by Simon Verbeke

  I've got a USB drive here, that somebody asked to try and fix. When inserting it, it shows up in explorer, but when I double click it I get a message saying "Please insert a disk into drive H:". So I went to disk management, to see if it was correctly formatted. It doesn't show up in the upper pane, and in the lower pane it tells me there is no medium in H:. After this I used chkdsk: the path is invalid. Then I tried TestDisk, which is supposed to look at raw data, and this can't even find the disk. So I'm assuming the drive is dead, even though its LED is burning. But I was wondering if there might be something else I could try? This system is Windows 7 Ultimate 64bit by the way. (I'm translating things from a Dutch install, so some names might be wrong)

  Read the article

• What are typical drive life times?

  - by Remus Rigo

  Can anyone tell me about the lifetime of drives (floppy, hard disk, CD, DVD, flash...)?

  Read the article

• What are typical drive lifetimes?

  - by Remus Rigo

  Can anyone tell me about the lifetime of drives (floppy, hard disk, CD, DVD, flash...)?

  Read the article

• SOS, i erased a disk,1T.by mistake

  - by gabriel

  i tried to make bootable a flash drive from the startup disk creator, and i wanted to copy an iso of the 11.10 ubuntu, and when i tried to erase the flash drive i pressed erase on another removable drive 1T storage by mistake, VVVery very very quickly less than one second and with no warning everything was erased i suppose.Is that thing possible?When i tried before theis to erase the flash drive it took around a minute to erase the 8GB.But now less than a second for 1T? Please help, Gabriel

  Read the article

• Checksum Errors From Hard Disk

  - by Ademos

  After running GSmartControl, I received three checksum errors on my storage hard disk. Error in Attribute Data structure: checksum error Error in Attribute Thresholds structure: checksum error Error in ATA Error Log structure: checksum error Does this indicate a hard disk failure? Because, this is the THIRD TIME I have replaced the same hard disk. (after seeing this error) The hard disk is a Western Digital Caviar Green. (2 TB)

  Read the article

• How to read Mac floppy on a PC?

  - by Robot

  I have a floppy made on a Mac years ago. I'd like to pull some files from it, but Macs haven't had floppies in forever, so I don't have one. I tried an app called MacOpener, but it didn't seem to work, plus it was pretty old. I even tried sharing the PC's A:\ drive and accessing it remotely from a Mac, but that didn't work either. Any ideas?

  Read the article

• How to read Mac floppy on a PC?

  - by Robot

  I have a floppy made on a Mac years ago. I'd like to pull some files from it, but Macs haven't had floppies in forever, so I don't have one. I tried an app called MacOpener, but it didn't seem to work, plus it was pretty old. I even tried sharing the PC's A:\ drive and accessing it remotely from a Mac, but that didn't work either. Any ideas?

  Read the article

• What Linux fits on a floppy disk?

  - by Peter Mortensen

  Which Linux'es fit on a 1.44 MB bootable floppy disk? Where can the .img image files be downloaded?

  Read the article

• Make a bootable cd from a floppy!

  - by Osama Gamal

  Hi, I have followed this tutorial http://wiki.osdev.org/Bare_bones to build a simple C kernel and boot it successfully. But, how to convert the floppy image to CD image to use it with my real PC?

  Read the article

• creating .flp floppy image in osx

  - by romant

  Need to pack some HDD drivers for a WinXP install. How can I create the coveted .flp image if I have the floppy extract? Thank you.

  Read the article

• ESX guest machine floppy drives

  - by warren

  What purpose does having a virtual floppy drive on a guest in ESX serve? Is there a way to configure ESX by default to NOT include such a device? It's annoying to have to remove it by hand once a new VM is ready to be provisioned.

  Read the article

• DPM 2010 "Disk failed or disk not found"

  - by SysAdmin

  I have an HP Proliant ML110 G5 server with Windows server 2008R2 only dedicated for DPM 2010. This server has a limit in HD of 8TB which has already been met. I'm now stuck in this situation where my disk keeps failing "Disk failed or Disk not found" in the disk management. Only after I reboot the system the disk comes back up. Today I was running my monthly tape backup on a certain protection group and the disk failed again while the tape job was running (so the job wasn't completed). This is the description of the error in the alerts: "The disk Disk 1 - Hitachi HDS722020ALA330 SCSI Disk Device cannot be detected or has stopped responding. All subsequent protection activities that use this disk will fail until the disk is brought back online. (ID 3120)". My backup system is becoming useless! I don't think that is a hardware issue (please correct me if I'm wrong) since the HD works fine for a certain period of time which is becoming shorter and shorter. I basically have no more option to fix this problem. I tried to fix any error that was coming up in the event viewer with no luck (included one regarding the SQL2008 compatibility issue). The disk keeps failing! Now I'm only trying to recover/migrate the data from the disk that is having problem but my issue now is that I cannot add any drives to my server since I already got installed the maximum storage capacity 8TB. I thought about 2 simple options. Please tell me what you guys think about it; Unplug one of the 2 storage pool disks (disk0, that one without problem) from the machine and install a new one in order to migrate the data with the Migration tool for DPM. Remove the defective disk (disk1), put back the disk0 and run the synchronization/consistency check on all the groups to recreate replicas and recovery points. Run diskpart.exe and clean up the disk (loosing all data) and hoping that he will work after I sync all the protection groups. Both solutions are not elegant but I have no better options at the moment. Please I need some help. Thanks for your time Angelo

  Read the article

• Vista Pen drive error: Please insert disk into removable drive

  - by pineapple

  Whenever I insert pen drive, I am not able to open it, it gives me the above error. I have tried changing drive letter but all in vain.Please help

  Read the article

• Running a Check-Disk (Is it dangerous)

  - by vaccano

  I have a lap top that a friend of mine would like me to fix. It is giving a blue screen on boot up. When I looked up the error message it indicates that I should run a check disk. Is this dangerous? Should I try to off load stuff from the hard drive first? I ask because I had a hard drive of my own that when I ran check disk it wiped a bunch of "bad sectors" and I lost most of the info on it (but it had been going bad). Opinions?

  Read the article

• Idle hard disk makes noise.

  - by ULTRA_POROV

  Like a fan or something. I checked it. I stopped all fans (cpu, video, psu) and the noise was still there. I read online that it might be a motor or something. I have put a great deal of effort making my pc quiet. Installed a quiet psu and cpu fan, reduced the fan speed of my video card, bought a ssd... But my drive for data makes this noise. I would never have expected that. Do all hard disks make this kind of noise? I guess most people won't notice it because of the other fans they have in the system, I however can hear it quite clearly because all my other fans are almost silent. So should i get a new one or should i just live with it, considering that i might end up with a drive that also makes this noise.

  Read the article

• Add Mirror for volumes other than the last one in Windows 7 (disk "not up-to-date")

  - by rakslice

  I'm using Windows 7 x64 Ultimate. I have an existing 4TB disk with 3 NTFS volumes, a new 3TB blank disk, and I'm trying to mirror the volumes onto the new disk. My Windows install is on an SSD which is Disk 0. The 4TB disk with volumes is Disk 1, and the new blank disk is Disk 2. I can add a mirror successfully for the last volume, but when I try to add a mirror for the first volume I immediately get errors (see below). Is there something I special I need to do to add a mirror for a volume other than the last one? More info: I opened Disk Management, right-clicked on the first volume on the existing disk, went to Add Mirror, and selected the new disk. The first time I did this I was prompted to convert the new disk to a Dynamic Disk, which I approved. Subsequently I got a message: The operation failed to complete because the Disk Management console view is not up-to-date. Refresh the view by using the refresh task. If the problem persists close the Disk Management console, then restart Disk Management or restart the computer. I've refreshed disk management, restarted the computer, and converted the new disk to basic and back to dynamic, but I still get that error message. Looking around for suggestions of a workaround, I saw a suggestion to use the diskpart command line tool. Running diskpart from the Start Menu as Administrator, I did select volume 2 (the first volume I want to mirror) and then add disk 2 (the new disk), and received a somewhat similar error: Virtual Disk Service error: The disk's extent information is corrupted. DiskPart has referenced an object which is not up-to-date. Refresh the object by using the RESCAN command. If the problem persists exit DiskPart, then restart DiskPart or restart the computer. A rescan appears to be successful: DISKPART> select disk 2 Disk 2 is now the selected disk. DISKPART> rescan Please wait while DiskPart scans your configuration... DiskPart has finished scanning your configuration. but attempting to add the mirror again resulted in the same error. The only similar report I found online was this: http://www.sevenforums.com/hardware-devices/335780-unable-mirror-all-but-last-partition-drive.html Based on that I attempted to mirror the last volume on the disk to the new disk using diskpart, and that started successfully -- it is currently resynchronizing. More Background: In the course of dealing with a failing 3TB hard drive, I bought a replacement 4TB drive and installed it, then copied the partitions from the failing drive to it using Minitool Partition Wizard Home, and then removed the failing drive and was up and running again normally. Now I've received a warranty replacement for the failing drive, and installed it, and now I'm attempting to mirror my partitions to it.

  Read the article

• Check the disk for problems on Debian Lenny

  - by Equ

  Hi guys! I just bought a VPS hosting with Debian Lenny (I'm new to all this world). I've managed to install and setup everthing I need pretty well. My testing website works fast as expected most of the time, but sometimes it is really slow (response time is about 5-10 seconds). I checked everything and seems that there are may be some disk issues. How can I check the disk for problems/performance? What else could possible cause such a behaviour? Thank you!

  Read the article

• Can't Read/Write the Hard disk used in NAS

  - by mgpyone

  I've lately purchased a Synology DS212j and I intended to use my two 3.5" HDs into it. One of them was in used as an external HD. Thus when I install these two unit in NAS, it asked me to formatted in order to used with its format (I think it's ext3?) . I installed the Disks and omit the formatting option. I just got another 3.5" Hard Disk now. I've installed it in the NAS. everything's fine. However, when I take out the (used) HD from the NAS and install back in the standalone casing, I found out that it can't be read from both OSX an Windows 7. I've tried with ext2sd and I only found 2GB portion of the whole 1.5 TB Hard Disk. Here's another reference from EASEUS Partition Master

  Read the article

• format/build raid 5 with one 4k drive, three 512b

  - by skidawgz

  I have 4 WD 1TB drives which I want to 4x1TB Raid5. I am not sure what course of action to take next. How do I configure my 4th drive (sde) to align with the rest? Will this affect performance? I rcv this msg (which brings me here to ask these question): The device presents a logical sector size that is smaller than the physical sector size. Aligning to a physical sector (or optimal I/O) size boundary is recommended, or performance may be impacted. fdisk -l shows: Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xf324ba09 Device Boot Start End Blocks Id System /dev/sdb1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x38bcc1f0 Device Boot Start End Blocks Id System /dev/sdc1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 81 heads, 63 sectors/track, 382818 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x570f77e7 Device Boot Start End Blocks Id System /dev/sdd1 2048 1953525167 976761560 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xeb665e7b Device Boot Start End Blocks Id System

  Read the article

• Move entire OS from NTFS drive to bigger ext4 drive.

  - by pangel

  According to SMART data, the hard drive I curently use is about to fail. I bought a new, bigger drive to copy the system to a safer place. The old drive is 160GB. Ubuntu was installed with Wubi, and the partition is NTFS. There are a few other partitions around (recovery partition, swap...) that I don't care about. The new drive is 320GB. I would like the new system to run on ext4, not on NTFS. I looked at solutions that use dd, or clonezilla, but it seems that moving to a different filesystem prevents me from using them. I considered installing a brand new ubuntu on the new hard drive and then copy /home from the old drive to the new drive, but I heard that there would be file permission problems. I would also have to reinstall all my software. One last thing: the NTFS drive has dead sectors. I don't know how this can influence the copy process, but I mention it just in case. edit: I do not care about the windows partition. I just want Ubuntu to make the transition.

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >