Search Results

Search found 119 results on 5 pages for 'upnp'.

Page 5/5 | < Previous Page | 1 2 3 4 5 

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Router(s) Issue: DNS quries sporadically fail with multiple computers hooked in

  - by bob-the-destroyer

  Basically, after anywhere from 5-60 minutes, DNS queries fail for a few minutes, then slowly begin to resolve correctly. Then the cycle repeats. This occurs only when more than one computer is on the network. All computers on the network experiences the same sporadic DNS outage at the same time. Wireless or wired, Linux or Windows, fresh OS install or old, browser or ping, same symptoms. Duplicated on 3 routers (not chained together, mind you) and 3 ISP's and 3 separate locations over the past several months. The only common theme is a single 5-yo WIN XP laptop which has been in use on the network throughout all this. There also may be anywhere between 1 - 10 devices hooked up wired or wirelessly at a time. The only reprieve I have from this torture is by using any VPN to an outside source - always smooth sailing. I typically set up any router to a) use WPA2/etc security; b) MAC whitelist; c) UPNP OFF (if available); d) always update firmware when available; e) obtain DNS from ISP automatically; f) set the router to act as DHCP server for the internal network. Adjusting channels has no effect. Any ideas?

  Read the article

• Wifi antenna extension with F-connector/RG-6(RG-59) cable?

  - by rjz2000

  In an older house, the wire mesh in walls surrounding the furnace behave like a Faraday cage and block wifi signals. It is also difficult to lay new cable, however there is television cable to multiple locations due to there once having been a roof-installed, television antenna. It would be relatively trivial to install the wifi router at the center distribution point, then have the antenna broadcasting/receiving the signal plugged in at each of the old television outlets. I assume that it would not be too difficult to find an adapter for SMA <- F-type connectors. The cable is actually RG-59 rather than RG-6, but I assume that it still has relatively good RF isolation along its length, which is no more than a couple hundred feet in any direction. Does anyone know a problem with the idea? Will a router get confused if there is /too little/ interference between the two antenna? Is that length of cable (~100ft) too long for the signal a router broadcasts? I have seen that it is also possible to use old ~$30/each FiOS cable modems available on eBay to extend a network over television cable. However, that seems like a less elegant solution, and might interfere with upnp and dlna services I'd like to have work on a single network. Thanks if anyone has answers or suggestions before I try this project!

  Read the article

• Remotely port forward/launch process or a client-less remote desktop app?

  - by DC177E

  I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

  Read the article

• DSL Modem with Wireless Router

  - by David

  I have a D-Link WBR-1310 wireless router and a TP-Link TD-8616 DSL modem. My old DSL modem died recently and I got the TP-Link as a replacement. With my old DSL modem, I plugged it into the WAN port on my D-Link and I could reach the internet through wireless and through the network. However, when I plugged the new TP-Link into the WAN port, I was not able to get any internet connectivity (either on the network ports or through wireless). So I plugged my labtop directly into the TP-Link DSL modem and I was able to get internet connectivity. I'm trying to figure out why my labtop can see the internet connection, but not the D-Link router. I think that the problem is due to the IP networking. My D-Link was originally set to have IP address 192.168.1.1. According to the documentation for the TP-Link DSL modem, it uses 192.168.1.1 as its IP address. I do not believe that my old DSL modem had an IP address. I logged into my D-Link router and changed its IP address to 192.168.1.2 and restarted it. Unfortunately, I still could not see the internet from my wireless devices. I've read a few forum postings which implied that I needed to setup a "bridge" between the two networks. Does that sound correct? Why didn't my old DSL modem require a bridge? I read pg. 12-13 of my D-Link's manual and they suggest that I need to disable UPnP, DHCP, and then plug the DSL modem into one of the LAN ports on my router. I'm concerned about doing this since I don't think that the firewall will work if I plug my DSL modem into one of the LAN ports. I also have a home NAS on my network and I wouldn't want that to be available over the internet. Does anyone have any advice about how I can get my TPLink DSL modem to work with my D-Link router? Thanks!

  Read the article

• What are some of the best wireless routers for a price-conscious home power-user?

  - by Alain

  I'm extremely dissatisfied with the 'popular' choice for routers in homes and small offices. They are expensive (upwards of 60$), lack a great deal of useful configuration options, and seem to need to be restarted quite often. (Linksys comes to mind). I've been on the market for a good router lately, and slowly collecting a set of requirements I feel good routers should meet. Maximum number of TCP/IP connections. - This isn't something I see any routers advertise, but in terms of supporting torrent applications, I've been screwed by routers that support less than 20 here. From what I understand a fairly standard number is 200, but there are not so expensive routers that support thousands. Router configuration menu - Most have standard menu's that let you set up basic things like your wireless network encryption settings, uPnP, and maybe even DMZ (demilitarized zones). An absolute requirement for me, however, are routers with good enough firmware to support: Explicit Port forwarding Assigning static local ips to specific mac addresses, or at least Port forwarding by MAC address Port, IP and MAC filtering Dynamic DNS service for home users who want to set up a server but have a dynamic IP Traffic shaping (ideally) - giving priority to packets from certain machines or over certain ports. Strong wireless signal - If getting a reliable signal requires me to be so close to the router that I can connect an Ethernet cable, it's not good enough. As many Ethernet ports as possible. - Because I want to be able to switch from console gaming to PC gaming without visiting my router. So far, the best thing I've stumbled upon (in the bargain bin at staples) was a 20$ retail plus router. It was meant to be the cheapest alternative until I could find something better to purchase online, but I was actually blown away by the firmware capabilities. It supports defining reserved bandwidth for certain network traffic, dynamic DNS, reserving local IPs for specific MAC addresses, etc. At 2 am when my roommate is killing our Internet with their torrents, I can limit their bandwidth without outright blacklisting them. I have, however, met serious limitations when it comes to network traffic between local machines. It claims a 300Mbps connection, but I have trouble streaming videos from my PC to my console or other laptops wirelessly. It has a meltdown and needs to be reset once in a while (no more than a couple times a month), and it's got a 200 connection limit. There 4 Ethernet ports in the back but I'm pretty sure the first doesn't work. So some great answers to this question would be: Any metrics you use to compare routers, and requirements you have for new candidates. The best routers you've found for supporting home servers, file management systems, high volume torrent traffic, good price/feature ratio, etc. Good configuration advice (aside from 'use Ethernet whenever possible') Thanks for your feedback and experiences!

  Read the article

• Making hosts accessible between LAN subnets

  - by nixnotwin

  I have two inerfaces on my router with tomato firmwre: br0 and vlan4. br0 is on 192.168.0.0/16 subnet and vlan4 on 10.0.1.0/24 subnet. As I don't want the different network services on br0 available on vlan4, I have added this firewall rule: iptables -I INPUT -i vlan4 -j ACCEPT; iptables -I FORWARD -i vlan4 -o vlan2 -m state --state NEW -j ACCEPT; iptables -I FORWARD -i br0 -o vlan4 -j DROP; vlan2 is my WAN (internet acess). The issue that I want to solve is that I want to make one host from 192.168.0.0/16 network (br0), which has ip 192.168.0.50, available on vlan4 (10.0.1.0/24). Only that host should be available on vlan4 (and all other hosts on br0 should be inaccessible). What firewall rules can be used to do it? Edit 1: Output of iptables -nvL FORWARD: Chain FORWARD (policy DROP 4 packets, 204 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- vlan4 192.168.0.50 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan4 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 229 13483 ACCEPT all -- vlan4 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 DROP all -- br0 vlan3 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- vlan3 ppp0 0.0.0.0/0 0.0.0.0/0 state NEW 67 3405 ACCEPT all -- vlan3 vlan2 0.0.0.0/0 0.0.0.0/0 state NEW 0 0 ACCEPT all -- br0 br0 0.0.0.0/0 0.0.0.0/0 34 1360 DROP all -- * * 0.0.0.0/0 0.0.0.0/0 state INVALID 758 40580 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 11781 2111K restrict all -- * vlan2 0.0.0.0/0 0.0.0.0/0 26837 19M ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 wanin all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 287 15927 wanout all -- * vlan2 0.0.0.0/0 0.0.0.0/0 283 15723 ACCEPT all -- br0 * 0.0.0.0/0 0.0.0.0/0 0 0 upnp all -- vlan2 * 0.0.0.0/0 0.0.0.0/0 Output of iptables -t nat -nvL PREROUTING: Chain PREROUTING (policy ACCEPT 6887 packets, 526K bytes) pkts bytes target prot opt in out source destination 855 83626 WANPREROUTING all -- * * 0.0.0.0/0 222.228.137.223 0 0 DROP all -- vlan2 * 0.0.0.0/0 192.168.0.0/16 0 0 DNAT udp -- * * 192.168.0.0/16 !192.168.0.0/16 udp dpt:53 to:192.168.0.1

  Read the article

• Problems when trying to connect to a router wirelessly

  - by Ruud Lenders

  The situation - At my girlfriend's parents' place there are six Windows 7 devices that are wired or wireless connected to a router: 3 dekstops and 3 laptops. There are also several smartphones using the router. The router is secured with WPA2 (AES). The problem - We never had any problems with the router for over a year. But recently - about 3 weeks ago - my girlfriend's laptop (HP) and my laptop (ASUS) started to develop problems while trying to connect to the router. The router has stopped showing up from the network list. Sometimes it comes back and shows up, but then it keeps saying something along the lines of "Could not connect", and not long after that it dissapears again. The range of the router is not the problem here, because we experience the same when we sit next to the router. Sometimes, if we are lucky, and waited a long time (10-15 minutes) without using the laptop for anything, the laptop will eventually succesful connect to the router. The attempts - Of course, the Window 7 troubleshooter. We tried troubleshooting the connection problems and the wireless network adapter, but no luck. We also reset the router enough times to know that's not helping either. Here's the full list of things we tried, but did not help: Running the Windows 7 troubleshooter Resetting the router (more than once) Setting the router settings to factory defaults Disconnecting all other devices except one laptop Applying a system restore Trying static/dynamic IP/DNS - Dynamic is better, right? Enabling/disabling IPv6 - Should I keep IPv6 disabled? Running the command: netsh wlan stop hostednetwork Running the command: netsh wlan set hostednetwork mode=disallow Updating/reïnstalling wireless adapter drivers The tests - To help finding the core of the problem, we tested the following: Plugging an ethernet cable in the router and in our laptops - worked fine Connecting someone else's laptop to the router (wireless) - worked fine Connecting our laptops to someone else's router - worked fine The router - This information might be relevant: Router model: Sitecom 300N Wireless Router Router hardware: version 01 The DCHP Server's IPs range from 192.168.0.100 to 192.168.0.200. Router settings: Wireless channel: 12 Channel bandwidth: 20/40 MHz Extension channel: 8 Preamble type: Long 802.11g protection: Disabled UPnP: Enabled The laptops - If you are wondering about our laptops: My laptop model: ASUS Pro64JQ Girlfriend's laptop: HP Pavillion G6 OS: Both Windows 7 Professional x64 - with Service Pack 1 My wireless adapter: Atheros AR9285 AdHoc 11n: Enabled The question - Does anyone have experienced the same problems as I do? Or does someone know how to solve this? Are there more tricks I can try, or settings I should change? Note - Our laptops are not slow or old. My laptop is 1.5 years old, and the other laptop is just 5 months old. I know how to keep laptops clean and I'm pretty sure both laptops are not bloated with useless software.

  Read the article

• Wireless traffic stops when downloading large files at high speed: packets lost (Linksys WRT120N router)

  - by Torious

  The problem Note: First I'd like to understand WHY this is happening. Ofcourse, a solution would be nice too. :) When downloading a large file over HTTP at high-speeds, my wireless traffic basically stops: I can't open webpages and the download itself pauses. It pauses pretty much immediately after starting it; sometimes at 800 KB, sometimes at a few MB. After some time, the download (and other traffic) resumes, but the problem keeps reoccurring during the same download. The problem does not occur when using a wired connection through the same router (Linskys WRT120N). Also note that the connection is not dropped when this happens. It's just that the traffic stops and I can't browse to web pages, etc. (SYN packets are sent but nothing is received, etc.) Inspection with Wireshark shows that the following happens: Server sends data packets which are acknowledged by client Server sends a packet, but SEQ indicates some packets were lost (6 packets in one occurrence). Server sends a few more packets and client acknowledges these using "selective acknowledgement" Server stops sending data for a while (since the lost packets were not acknowledged or the router stops forwarding them?) Eventually, server does a "retransmission" and traffic resumes as normal. This all seems normal behavior to me when packet loss occurs. It's the consistent packet loss throughout a large, high-speed download that puzzles me. What might cause this? My own idea is the following: My internet is pretty fast (100 mbps), so when starting a large-file download, the router buffers the incoming data (since wireless introduces some slight delay / lower speed, in part due to other networks), but the buffer overflows and the router drops packets to regulate traffic (and because it has no choice). But how could that happen? Doesn't the TCP window size limit the amount of data that can go unacknowledged? So how can the router's buffer overflow if there can only be like 64 KB waiting to be acknowledged? Note: I've disabled TCP window scaling and dynamic window size through netsh options, in an attempt to fix this, but it doesn't seem to matter. Also, Wireshark shows a pattern of the server sending 2 packets (of 1514 bytes) and the client sending an ACK, so does that rule out a possible buffer overflow? And a few more subsequent packets are received... I'm at a loss here. Thanks for any insights. Things that are (probably) NOT the cause / I have experimented with The browser Various TCP options in Windows 7 (netsh etc.) Router settings such as MTU, beacon interval, UPnP, ...

  Read the article

• Setup Remote Access in Windows Home Server

  - by Mysticgeek

  One of the many awesome features of Windows Home Server, is the ability to access your server and other computers on your network remotely. Today we show you the steps to enable Remote Access to your home server from anywhere you have an Internet connection. Remote Access in Windows Home Server has a lot of great features like uploading and downloading files from shared folders, accessing files from machines on your network, and controling machines remotely (on supported OS versions). Here we take a look at the basics of setting it up, choosing a domain name, and verifying you can connect remotely. Setup Remote Access in Windows Home Server Open the Windows Home Server Console and click on Settings. Next select Remote Access, it is off by default, just click the button to turn it on. Wait while your router is configured for remote access, when it’s complete click Next. Notice that it will enable UPnP, if you don’t wish to have that enabled, you can manually forward the correct ports. If you have any problems with the router being automatically configured, we’ll be taking a look at a more detailed troubleshooting guide in the future. The router is successfully configured, and we can continue to the next process of configuring our domain name. The Domain Name Setup Wizard will start. Notice you will need a Windows Live ID to set it up –which is typically your hotmail address. If you don’t already have one, you can get one here. Type in your Live ID email address and password and click Next… Agree to the Home Server Privacy Statement and the Live Custom Domains Addendum. If you’re concerned about privacy and want to learn more about the domain addendum, make sure to read about it before agreeing. There is nothing abnormal to point out about either statement, but if this is your first time setting it up, it’s good to review the information.   Now choose a name for the domain. You should select something that is easy to remember and identifies your home server. The name can contain up to 63 characters, numbers, letters, and hyphens…and must begin and end with a letter or number. When you have the name figured out click the Confirm button. Note: You can only register one domain name per Live ID. If the name isn’t already taken, you’ll get a confirmation message indicating it’s god to go. The wizard is complete and you can now access the home server from the URL provided. A few other things to point out after you’ve set it up…under Domain Name click on the Details button… Which pulls up the domain detail information and you can refresh the data to verify everything is working correctly. Or you can click the Configure button and then change or release your current domain name. Under Web site settings, you can change you site page headline to whatever you want it to be. Accessing Home Server Remotely After you’ve gotten everything setup for your home server domain, you can begin to access it when you’re away from home. Simply type in the domain address you created in the previous steps. The start page is rather boring…and to start accessing your data, click the Log On button in the upper right hand corner. Then enter in your home server credentials to gain access to your files, folders, and network computers. You won’t be able to log in with your administrator user account however, to protect security of your network. Once you’re logged in, you’ll be able to access different parts of your home server shares and network computers. Conclusion Now that you have Remote Access setup, you should be able to access and manage your files easily. Being able to access data from your home server remotely is great when you need to get certain files while on the road. The web UI is pretty self explanatory, works best in IE as ActiveX is required, and is smooth and easy to work with. In future articles we’ll be covering a lot more regarding remote access, including more of the available features, troubleshooting connection issues, and enabling access for other users. Similar Articles Productive Geek Tips GMedia Blog: Setting Up a Windows Home ServerHow to Remote Desktop to the Actual Server Console on Windows 2003Use Windows Vista Aero through Remote Desktop ConnectionAccess Your MySQL Server Remotely Over SSHShare Ubuntu Home Directories using Samba TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Penolo Lets You Share Sketches On Twitter Visit Woolyss.com for Old School Games, Music and Videos Add a Custom Title in IE using Spybot or Spyware Blaster When You Need to Hail a Taxi in NYC Live Map of Marine Traffic NoSquint Remembers Site Specific Zoom Levels (Firefox)

  Read the article

• Huawei b153 limit of devices

  - by bdecaf

  I set up my home network all through this 3G wifi router. Problem is it only allows 5 devices to connect. That's not much especially if a wifi printer and gaming consoles keep hogging these slots. On the other hand I don't see the point on blocking these devices. They are (should) not doing anything online just intern in my network. The documentation I can find is surpirisingly unhelpful and focuses how to plug the device in a power socket. So what would be my options. Notes: I have already been able to get a shell on the device using ssh. It's running some Busybox. But I fail to find the how and where this limit is enforced/created. Notes 2: Specifically my device is a 3WebCube - unfortunately not specifically marked with the Huawei Model number. Successes so far After enabling ssh in the options I can login: ssh -T [email protected] [email protected]'s password: ------------------------------- -----Welcome to ATP Cli------ ------------------------------- unfortunately because of this -T - the tab key does not work for autocomplete and all inputted commands will be echoed. Also no history with arrow keys. ATP interface this custom interface is not very useful: ATP>help help Welcome to ATP command line tool. If any question, please input "?" at the end of command. ATP>? ? cls debug help save ? exit ATP>save? save? Command failed. ATP>save ? save ? ATP>debug ? debug ? display set trace ? Shell BUT undocumented - I somehow found on a auto translated chinese website - all you need to do is input sh ATP>sh sh BusyBox vv1.9.1 (2011-03-27 11:59:11 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. # builtin commands # help Built-in commands: ------------------- . : alias bg break cd chdir command continue eval exec exit export false fg getopts hash help jobs kill let local pwd read readonly return set shift source times trap true type ulimit umask unalias unset wait shows standard unix structure: # ls / var tmp proc linuxrc init etc bin usr sbin mnt lib html dev in /bin # ls /bin zebra strace ppps ln echo cat wscd startbsp pppc klog ebtables busybox wlancmd sshd ping kill dns brctl web sntp netstat iwpriv dhcps auth usbdiagd sms mount iwcontrol dhcpc atserver upnp sleep mknod iptables date atcmd upg siproxd mkdir ipcheck cp at umount sh mini_upnpd ip console ash test_at rm mic igmpproxy cms telnetd ripd ls ethcmd cmgr swapdev ps log equipcmd cli in /sbin # ls /sbin vconfig reboot insmod ifconfig arp route poweroff init halt using tftp after installing tftp on my desktop I was able to send files with tftp -s -l curcfg.xml 192.168.1.103 and to download onto the huawei with tftp -g -r curcfg.xml 192.168.1.103 I think I'll need that - because I don't see any editor installed. readout stuff (still playing around where I would get interesting info) For confirmation of hardware: # cat /var/log/modem_hardware_name ^HWVER:"WL1B153M001"# # cat /var/log/modem_software_name 1096.11.03.02.107 # cat /var/log/product_name B153

  Read the article

• TV not detected by Windows/VGA - when there is a WHDI device in the signal chain

  - by ashwalk

  I'm at my wit's end with this one... I had an EVGA GTS 250, and I used to plug it's HDMI out into a WHDI sender, which transmitted to its corresponding WHDI receiver 15ft away, which then connected to a Samsung LN40D LCD TV through another HDMI cable. PC/VGA < [hdmi cable] < WHDI sender <[air] WHDI receiver < [hdmi cable] < TV It was perfect, stable, no perceivable latency. I just plugged everything the first time and it worked instantly. It sent 5.1 audio, and Windows/nVidia Control Center detected the TV by its name. The WHDI device is this one: http://goo.gl/Q8iWI5 Now I bought an EVGA GTX 650, and WHDI doesn't work anymore. Both Windows and nVidia Control Center won't detect the TV, only the monitor that's connected via DVI. The TV screen shows "TX202913 connected. Check video signal." on top of a black screen. Though the device is not the problem itself, just the fact that it's not allowing direct connection between PC and TV. I would bet that if put an AVR in its place I'd also have this issue. The HDMI on this new card works with other monitors. If I put the older card back, WHDI works normally. I have googled this for 5 months on and off. Once I bumped into a page that showed how to force a display device to always-on through registry edit. Once I restarted windows, the Tv (through WHDI) displayed my expanded or duplicated desktop at 1024x768 ONLY, and listed the display as "digital display". I could not change the resolution and it wouldn't playback audio (although the option was available at nVidia Control Center HDMI audio options, but did not work). This proves that there is no conflict between the devices, except that software-wise, Windows cannot, for the life of it, understand that there's a TV there to send video/audio to. Since this won't do (no audio, poor video), I reverted this regedit. It's also not an EDID problem within the TV, since when connected directly it works. The last weird bit of this saga is that today, I reminded of Windows' "Add Device" dialog, gave it a go, and a "Samsung Generic UPNP TV" showed up, which I promptly installed the drives for, rising to a climax of... ...NOTHING HAPPENING. As far as I can tell, it really didn't change anything other than using up a few kb in my main disc. I should also say that I looked a LOT into handshake problems and nothing applied either. Do any of you have an idea of what may be going on? I can't stand the thought of having a us$200 device not working because of the addition of a newer graphics card, when the much older one had no issues. There is absolutely NO REASON for this to happen. There is NO documentation on WHDI online. Apparently no one buys this stuff. For the same reason, no one responded to this same plea for help on NVidia and EVGA forums. Worst case, this can be a warning about this setup for people in the future. Thanx in advance.

  Read the article

• CodePlex Daily Summary for Sunday, September 30, 2012

  CodePlex Daily Summary for Sunday, September 30, 2012Popular ReleasesCAPTCHA Solver: Initial Release: This is the initial Release :) Still very much a WIP.MCEBuddy 2.x: MCEBuddy 2.2.17: Reccomended update to 2.2.16 Changelog for 2.2.17 (32bit and 64bit) 1. Fixed bugs around thread synchronization with new remote model (fixes cause the app to crash or hang) 2. Updated UPnP code base, faster and more reliable now 3. Now you can get audio/video properties for multiple files on main page. Selected multiple files and right click, all selected files properties will be shown. 4. Fix a bug, not able to enter a conversion task name in the GUIAggravation: Version 1.0: This version 1.0 release is pretty stable. You need the Silverlight 4 runtime, developer tools, and Experssion Blend 4 installed.Readable Passphrase Generator: KeePass Plugin 0.7.1: See the KeePass Plugin Step By Step Guide for instructions on how to install the plugin. Changes Built against KeePass 2.20Windows 8 Toolkit - Charts and More: Beta 1.0: The First Compiled Version of my LibraryPDF.NET: PDF.NET.Ver4.5-OpenSourceCode: PDF.NET Ver4.5 ????，????Web??????。 PDF.NET Ver4.5 Open Source Code,include a sample Web application project.D3 Loot Tracker: 1.4: Session name is displayed in the UI. Changes data directory for clickonce deployment so that sessions files are persisted between versions. Added a delete button in the sessions list window. Allow opening of the sessions local folder from the session list widow. Display the session name in the main window Ability to select which diablo process to hook up to when pressing new () function BUT only if multi-process support is selected in the generals settings tab menu. Session picker...CRM 2011 Visual Ribbon Editor: Visual Ribbon Editor 1.1 Beta: Visual Ribbon Editor 1.1 Beta What's New: Fixed scrolling issue in UnHide dialog Added support for connecting via ADFS / IFD Added support for more than one action for a button Added support for empty StringParameter for Javascript functions Fixed bug in rule CrmClientTypeRule when selecting Outlook option Extended Prefix field in New Button dialogVisual Studio Icon Patcher: Version 1.5.2: This version contains no new images from v1.5.1 Contains the following improvements: Better support for detecting the installed languages The extract & inject commands won’t run if Visual Studio is running You may now run in extract or inject mode The p/invoke code was cleaned up based on Code Analysis recommendations When a p/invoke method fails the Win32 error message is now displayed Error messages use red text Status messages use green textZXing.Net: ZXing.Net 0.9.0.0: On the way to a release 1.0 the API should be stable now with this version. sync with rev. 2393 of the java version improved api better Unity support Windows RT binaries Windows CE binaries new Windows Service demo new WPF demo WindowsCE Hotfix: Fixes an error with ISO8859-1 encoding and scannning of QR-Codes. The hotfix is only needed for the WindowsCE platform.C.B.R. : Comic Book Reader: CBR 0.7: Synthesis since 0.6 : ePUB : Complete refactoring Add a new dedicated feed viewer for opds stream PDF conversion : improved with image merge Make all backstage panel scrollable Integrate the new AvalonDock 2 library. Support multi-document. Library explorer and Table of content are now toolboxes Designer for dynamic books is now mvvm and much better New BrowserForControl Customized xps viewer to suppress toolbars and bind it to cbr commands Add quick start manual and button ...menu4web: menu4web 1.0 - free javascript menu for web sites: menu4web 1.0 has been tested with all major browsers: Firefox, Chrome, IE, Opera and Safari. Minified m4w.js library is less than 9K. Includes 21 menu examples of different styles. Can be freely distributed under The MIT License (MIT).Rawr: Rawr 5.0.0: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...Coevery - Free CRM: Coevery 1.0.0.26: The zh-CN issue has been solved. We also add a project management module.VidCoder: 1.4.1 Beta: Updated to HandBrake 4971. This should fix some issues with stuck PGS subtitles. Fixed build break which prevented pre-compiled XML serializers from showing up. Fixed problem where a preset would get errantly marked as modified when re-opening the encode settings window or importing a new preset.Snake!: Snake 1.0: Version 1 StablePaging SharePoint ListItems using listitems position: Paginglistitems V1.0: This is a console application which has two methods both on CSOM and SOM to display the listitems in a paged manner.SharePoint Move Discussion Threads: SharePoint Move Discussion Threads ver 0.1: ver 0.1NTCPMSG: V1.1.1.0: increase the performance. Support .net framework 4.0.BlackJumboDog: Ver5.7.2: 2012.09.23 Ver5.7.2 (1)InetTest?? (2)HTTP?????????????????100???????????New Projects2D Sprite Editor: This is a 2d sprite editor. Import your sprite sheet, trace your animations frame and export the coordinates points in a simple txt file, ready to import.caifenweb1: test project.CatchThatException: This is a small logging library We created at developerpath.com to help us log exceptions. It write it to a text file and you can easilay open that txt.FsxWs - WebServices for Microsoft FSX: WebServices for MS Flight Simulator. Get flights data as JSON, KML. !! Still in SetUp phase - be patient !!GetTPB: Some training in downloading and parsing web pages, with multithreading too.JSON-RPC Client Generator (for XBMC): The goal of this project is to provide a .Net client for the XBMC JSONRPC API. The main part is not XBMC dependent and may be used for any JSON-RPC client.matlab-silhouette-pose-wtf: Whatevermfp: this is random codeMVC Grid: MVC Grid ExampleMyWebSocketTry: sssssssssssssssssssssssssssssssssssssssNetduino Console: Netduino Console is an interface with built in messaging layers that allows you as a developer to dynamically create plugins following a provided interface to iSharePoint ASP.NET Verifier: Project will allow to verify SharePoint 2010 components using ASP.NET web applicationSharepoint Custom Upload: This is a SharePoint solution that allows an administrator to customize the upload page individually for each document library in a site.. It allows you to makeWinWeb Browser Deluxe: WinWeb Browser Deluxe es un navegador web de código abierto basado en Internet Explorer hecho en Visual Basic .NET. Descargalo ya!writethatoutput: This is the official release page for WriteThatOutPut from developerpath.com

  Read the article

• Windows 7 Machine Makes Router Drop -All- Wireless Connections

  - by Hammer Bro.

  Some background: My home network consists of my Desktop, a two-month old Windows 7 (x64) machine which is online most frequently (N-spec), as well as three other Windows XP laptops (all G) that only connect every now and then (one for work, one for Netflix, and the other for infrequent regular laptop uses). I used to have a Belkin F5D8236-4 wireless router, and everything worked great. A week ago, however, I found out that the Belkin absolutely in no way would establish a VPN connection, something that has become important for work. So I bought a Netgear WNR3500v2/U/L. The wireless was acting a little sketchy at first for just the Windows 7 machine, but I thought it had something to do with 802.11N and I was in a hurry so I just fished up an ethernet cable and disabled the computer's wireless. It has now become apparent, though, that whenever the Windows 7 machine is connected to the router, all wireless connections become unstable. I was using my work laptop for a solid six hours today with no trouble, having multiple SSH connections open over VPN and streaming internet radio in the background. Then, within two minutes of turning on this Windows 7 box, I had lost all connectivity over the wireless. And I was two feet away from the router. The same sort of thing happens on all of the other laptops -- Netflix can be playing stuff all weekend, but if I come up here and do things on this (W7) computer, the streaming will be dead within ten minutes. So here are my basic observations: If the Windows 7 machine is off, then all connections will have a Signal Strength of Very Good or Excellent and a Speed of 48-54 Mbps for an indefinite amount of time. Shortly after the Windows 7 machine is turned on, all wireless connections will experience a consistent decline in Speed down to 1.0 Mbps, eventually losing their connection entirely. These machines will continue to maintain 70% signal strength, as observed by themselves and router. Once dropped, a wireless connection will have difficulty reconnecting. And, if a connection manages to become established, it will quickly drop off again. The Windows 7 machine itself will continue to function just fine if it's using a wired connection, although it will experience these same issues over the wireless. All of the drivers and firmwares are up to date, and this happened both with the stock Netgear firmware as well as the (current) DD-WRT. What I've tried: Making sure each computer is being assigned a distinct IP. (They are.) Disabling UPnP and Stateful Packet Inspection on the router. Disabling Network Sharing, SSDP Discovery, TCP/IP NetBios Helper and Computer Browser services on the Windows 7 machine. Disabling QoS Packet Scheduler, IPv6, and Link Layer Topology Discovery options on my ethernet controller (leaving only Client for Microsoft Networks, File and Printer Sharing, and IPv4 enabled). What I think: It seems awfully similar to the problems discussed in detail at http://social.msdn.microsoft.com/Forums/en/wsk/thread/1064e397-9d9b-4ae2-bc8e-c8798e591915 (which was both the most relevant and concrete information I could dig up on the internet). I still think that something the Windows 7 IP stack (or just Operating System itself) is doing is giving the router fits. However, I could be wrong, because I have two key differences. One is that most instances of this problem are reported as the entire router dying or restarting, and mine still works just fine over the wired connection. The other is that it's a new router, tested with both the factory firmware and the (I assume) well-maintained DD-WRT project. Even if Windows 7 is still secretly sending IPv6 packets or the TCP Window Scaling implementation that I hear Vista caused some trouble with (even though I've tried my best to disable anything fancy), this router should support those functions. I don't want to get a new or a replacement router unless someone can convince me that this is a defective unit. But the problem seems too specific and predictable by my instincts to be a hardware hiccup. And I don't want to deal with the inevitable problems that always seem to take half a day to resolve when getting a new router, since I'm frantically working (including tomorrow) to complete a project by next week's deadline. Plus, I think in the worst case scenario, I could keep this router connected directly to the modem, disable its wireless entirely, and connect the old Belkin to it directly. That should allow me to still use VPN (although I'll have to plug my work laptop directly into that router), and then maintain wireless connections for all of the other computers. But that feels so wrong to me. Anyone have any ideas what the cause and possible solution could be? Clarifications: The Windows 7 machine is directly connected via an ethernet cable to the router for everything above. But while it is online, all other computers' wireless connections become unusable. It is not an issue of signal strength or interference -- no other devices within scanning range are using Channel 1, and the problem will affect computers that are literally feet away from the router with 95% signal strength.

  Read the article

• Windows 7 Machine Makes Router Drop -All- Wireless Connections [closed]

  - by Hammer Bro.

  Note: I accidentally originally posted this question over at SuperUser, and I still think the issue is caused by some low-level networking practice of Windows 7, but I think the expertise here would be more apt to figuring it out. Apologies for the cross-post. Some background: My home network consists of my Desktop, a two-month old Windows 7 (x64) machine which is online most frequently (N-spec), as well as three other Windows XP laptops (all G) that only connect every now and then (one for work, one for Netflix, and the other for infrequent regular laptop uses). I used to have a Belkin F5D8236-4 wireless router, and everything worked great. A week ago, however, I found out that the Belkin absolutely in no way would establish a VPN connection, something that has become important for work. So I bought a Netgear WNR3500v2/U/L. The wireless was acting a little sketchy at first for just the Windows 7 machine, but I thought it had something to do with 802.11N and I was in a hurry so I just fished up an ethernet cable and disabled the computer's wireless. It has now become apparent, though, that whenever the Windows 7 machine is connected to the router, all wireless connections become unstable. I was using my work laptop for a solid six hours today with no trouble, having multiple SSH connections open over VPN and streaming internet radio in the background. Then, within two minutes of turning on this Windows 7 box, I had lost all connectivity over the wireless. And I was two feet away from the router. The same sort of thing happens on all of the other laptops -- Netflix can be playing stuff all weekend, but if I come up here and do things on this (W7) computer, the streaming will be dead within ten minutes. So here are my basic observations: If the Windows 7 machine is off, then all connections will have a Signal Strength of Very Good or Excellent and a Speed of 48-54 Mbps for an indefinite amount of time. Shortly after the Windows 7 machine is turned on, all wireless connections will experience a consistent decline in Speed down to 1.0 Mbps, eventually losing their connection entirely. These machines will continue to maintain 70% signal strength, as observed by themselves and router. Once dropped, a wireless connection will have difficulty reconnecting. And, if a connection manages to become established, it will quickly drop off again. The Windows 7 machine itself will continue to function just fine if it's using a wired connection, although it will experience these same issues over the wireless. All of the drivers and firmwares are up to date, and this happened both with the stock Netgear firmware as well as the (current) DD-WRT. What I've tried: Making sure each computer is being assigned a distinct IP. (They are.) Disabling UPnP and Stateful Packet Inspection on the router. Disabling Network Sharing, SSDP Discovery, TCP/IP NetBios Helper and Computer Browser services on the Windows 7 machine. Disabling QoS Packet Scheduler, IPv6, and Link Layer Topology Discovery options on my ethernet controller (leaving only Client for Microsoft Networks, File and Printer Sharing, and IPv4 enabled). What I think: It seems awfully similar to the problems discussed in detail at http://social.msdn.microsoft.com/Forums/en/wsk/thread/1064e397-9d9b-4ae2-bc8e-c8798e591915 (which was both the most relevant and concrete information I could dig up on the internet). I still think that something the Windows 7 IP stack (or just Operating System itself) is doing is giving the router fits. However, I could be wrong, because I have two key differences. One is that most instances of this problem are reported as the entire router dying or restarting, and mine still works just fine over the wired connection. The other is that it's a new router, tested with both the factory firmware and the (I assume) well-maintained DD-WRT project. Even if Windows 7 is still secretly sending IPv6 packets or the TCP Window Scaling implementation that I hear Vista caused some trouble with (even though I've tried my best to disable anything fancy), this router should support those functions. I don't want to get a new or a replacement router unless someone can convince me that this is a defective unit. But the problem seems too specific and predictable by my instincts to be a hardware hiccup. And I don't want to deal with the inevitable problems that always seem to take half a day to resolve when getting a new router, since I'm frantically working (including tomorrow) to complete a project by next week's deadline. Plus, I think in the worst case scenario, I could keep this router connected directly to the modem, disable its wireless entirely, and connect the old Belkin to it directly. That should allow me to still use VPN (although I'll have to plug my work laptop directly into that router), and then maintain wireless connections for all of the other computers. But that feels so wrong to me. Anyone have any ideas what the cause and possible solution could be? Clarifications: The Windows 7 machine is directly connected via an ethernet cable to the router for everything above. But while it is online, all other computers' wireless connections become unusable. It is not an issue of signal strength or interference -- no other devices within scanning range are using Channel 1, and the problem will affect computers that are literally feet away from the router with 95% signal strength.

  Read the article

• CodePlex Daily Summary for Sunday, October 21, 2012

  CodePlex Daily Summary for Sunday, October 21, 2012Popular ReleasesBlogEngine.NET: BlogEngine.NET 2.7 RC: Cheap ASP.NET Hosting - $4.95/Month - Click Here!! Click Here for More Info Cheap ASP.NET Hosting - $4.95/Month - Click Here! dot This is a Release Candidate version for BlogEngine.NET 2.7. The most current, stable version of BlogEngine.NET is version 2.6. Find out more about the BlogEngine.NET 2.7 RC here. To get started, be sure to check out our installation documentation. If you are upgrading from a previous version, please take a look at the Upgrading to BlogEngine.NET 2.7 instructions...Pulse: Pulse 0.6.3.0: Fixed a number of bugs that showed up since my update yesterday. Fixes included are for: - Weird issue where the initial "Nature" wallbase.cc search would duplicate itself - After changing a providers settings it wouldn't take affect until you restarted Pulse (removing or adding a provider entirely did take effect though) - Another small issue with the regex for the wallbase.cc wallpapers that I tweaked yesterday, seems good now though.Liberty: v3.4.0.0 Release 20th October 2012: Change Log -Added -Halo 4 support (invincibility, ammo editing) -Reach A warning dialog now shows up when you first attempt to swap a weapon -Fixed -A few minor bugsMCEBuddy 2.x: MCEBuddy 2.3.3: 1. MCEBuddy now supports PIPE (2.2.15 style) and the newer remote TCP communication. This is to solve problems with faulty Ceton network drivers and some issues with older system related to load. When using LOCALHOST, MCEBuddy uses PIPE communication otherwise it uses TCP based communication. 2. UPnP is now disabled by Default since it interferes with some TV Tuner cards (CETON) that represent themselves as Network devices (bad drivers). Also as a security measure to avoid external connection...Orchard Project: Orchard 1.6 RC: RELEASE NOTES This is the Release Candidate version of Orchard 1.6. You should use this version to prepare your current developments to the upcoming final release, and report problems. Please read our release notes for Orchard 1.6 RC: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you wil...Rawr: Rawr 5.0.1: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...Yahoo! UI Library: YUI Compressor for .Net: Version 2.1.1.0 - Sartha (BugFix): - Revered back the embedding of the 2x assemblies.Visual Studio Team Foundation Server Branching and Merging Guide: v2.1 - Visual Studio 2012: Welcome to the Branching and Merging Guide What is new? The Version Control specific discussions have been moved from the Branching and Merging Guide to the new Advanced Version Control Guide. The Branching and Merging Guide and the Advanced Version Control Guide have been ported to the new document style. See http://blogs.msdn.com/b/willy-peter_schaub/archive/2012/10/17/alm-rangers-raising-the-quality-bar-for-documentation-part-2.aspx for more information. Quality-Bar Details Documentatio...D3 Loot Tracker: 1.5.5: Compatible with 1.05.Write Once, Play Everywhere: MonoGame 3.0 (BETA): This is a beta release of the up coming MonoGame 3.0. It contains an Installer which will install a binary release of MonoGame on windows boxes with the following platforms. Windows, Linux, Android and Windows 8. If you need to build for iOS or Mac you will need to get the source code at this time as the installers for those platforms are not available yet. The installer will also install a bunch of Project templates for Visual Studio 2010 , 2012 and MonoDevleop. For those of you wish...Windawesome: Windawesome v1.4.1 x64: Fixed switching of applications across monitors Changed window flashing API (fix your config files) Added NetworkMonitorWidget (thanks to weiwen) Any issues/recommendations/requests for future versions? This is the 64-bit version of the release. Be sure to use that if you are on a 64-bit Windows. Works with "Required DLLs v3".Restful Objects for .NET: Restful Objects Server 1.0.1: Version 1.0.1 is a bug fix release - fixing bug #55 - a failure to conform to the Restful Objects spec (v.1.0.0) for the Parameters property on an Action Representation. Please note that the easiest way to use Restful Objects for .NET is as NuGet Packages: search the NuGet Public Gallery for 'restfulobjects'. It is only necessary to download the source (from here) if you wish to build and/or modify the framework yourself.Extensions.js: Extensions.js 0.8.3.6 (Release): Extensions.js provides type extensions to facilitate working with javascript objects in a style familiar to C# programmers.PdfReport: PdfReport 1.2: - Added navigation/nested properties support to StronglyTypedList DataSource. - Moved watermark location to the top layer. - Fixed grouping issue in multi column reports. - Fixed a typo, Pervious to Previous! - Added more than 25 samples. you can download them from the "source code" tab: http://pdfreport.codeplex.com/SourceControl/BrowseLatest - Added NuGet Package: http://nuget.org/packages/PdfReport/Merge PDF: MergePDF 1.0 Released: MergePDF 1.0 Released40FINGERS DotNetNuke StyleHelper: 40FINGERS StyleHelper Skin Object 02.06.04: Version 02.06.04:Bug Fix SuperUser Detection Passing IfRole="SuperUsers" did not detect Host users This has been corrected now and the code has been rewritten. New Attribute ContentFalse This is the content that gets injected when the conditions Version 02.06.03:Changed IfQs behavior: IfQs also to test if a query String Parameter exists You can now pass a QS paramter without value Where IfQS="ProductId:122" would test for a QS parameter ProductId with value 122 IfQS="ProductId" allows you t...Display attachments (list view) SP 2010: Display attachments (in list view) 1.0.0: Version 1.0.0: Display attachments for list item in list view Async loading attachments using library jQuery 1.8.2 Use sharepoint webservice (/vtibin/Lists.asmx) Simple in use Simple installation Localized: English RussianCODE Framework: 4.0.21017.0: See change log in the Documentation section for details.Magelia WebStore Open-source Ecommerce software: Magelia WebStore 2.1: Add support for .net 4.0 to Magelia.Webstore.Client and StarterSite version 2.1.254.3 Scheduler Import & Export feature (for Professional and Entreprise Editions) UTC datetime and timezone support .net 4.5 and Visual Studio 2012 migration client magelia global refactoring release of a nugget package to help developers speed up development http://nuget.org/packages/Magelia.Webstore.Client optimization of the data update mechanism (a.k.a. "burst") Performance improvment of the d...VFPX: FoxcodePlus: FoxcodePlus - Visual Studio like extensions to Visual FoxPro IntelliSense.New Projectsa new super fast css3 selector engine: kquery - A Super Fast And Compatible Css3 Selector Engine.AcfunWP: Acfun for Windows Phone??????MIT??????????，???????????Windows Phone?????????????????????。AdRotator v2: A highly customizable ad rotator component for Windows Phone and Windows 8 platforms, to be used with Silverlight, XNA and Monogame.BackUpCostaRicaProject: SumaryClickOnceTest: projekatCloudClipboardSync: Ha egy felhasználó eszközei közötti kommunikációról van szó, akkor a Dropbox és hasonló fájlszinkronizációs szolgáltatások felhasználhatók, mint korlátozott átvCodeplexTest: Enter two numbers to get the sum of them.cosuagwusumofnumbers: cosuagwu's sum of numberDaf Yomi WP7 App: Daf Yomi is a Windows Phone 7.5 application that let you listen to current Daf Yomi content from www.daf-yomi.com.Doctor Reg: Doctor Regfelixsumofnumbers: task1: getting two numbers from a user and calculating the sumFoxOS: La Volpe nel tuo osGanagro Lite: Windows forms application for handling grass-fed bull raising operations. Uses .net 3.5 and sql server (2005 or later). Written in c#, localized in spanish.GSISW8: ??a Windows Store efa?µ??? ? ?p??a pa???e? ?as??? St???e?a ??a ?? F?s??? ???s?pa ?a? F?s??? ???s?pa ?p?t?de?µat?e?, µ?s? t?? ???s?? t?? a????t?? Web Service t??JavaScript Calculator: ajogjoohon: Ua ua auaKRATOS: Kratos, the personification of power.Logical Disk Indicator: Logical Disk Indicator is a tool to monitor logical disk activity in notification area. Visual Basic.NET and .Net 2.0Media Organiser: This project aims to provide a tool that allows you not only to overview your media collection but also reorganize it following specific rules you can definePolymorphGame: A University project created in XNA integrating farseer physics engine. Contains some bugs and the code is not of the cleanest. Comments and critics welcome!qp: ????????? ??? ??????? ???? ?????? ????????? ? ???????????RAIP (Resonance Assignment by Integer Linear Programming): In progress...SanguoshaCardsCounter: SanguoshaCardsCounter??????????????????????????????。 ?????Microsoft Visual Studio 2012????C#????.NET Framework 4.5??。SimpleCalculatorProject: A simple calculator that adds two integers and displays the resultSJKP.PdfConversion: SharePoint 2010 Service Application framework, containing the infrastructure for easy OCR processing of PDF files in lists. A OCR component is not included.SoftwareTestingConcepts: Website gives information about Software Testing Concepts.SpeakToMe: SpeakToMe is a natural language processor that works by tokenizing the input based on known concepts and then matches the token structure against a set of rulesTododoo: This is my small hobby project - the simpliest todo-list possible.TokenUtil: TokenUtil is a command line program for requesting a token from a Security Token Service.VS2012 MSHA file builder: visual studio 2012 help view msha file creation

  Read the article

• CodePlex Daily Summary for Saturday, October 20, 2012

  CodePlex Daily Summary for Saturday, October 20, 2012Popular ReleasesP1 Port monitoring with Netduino Plus: V0.3 New release with new features: This V0.3 release that is made public on the 20th of October 2012 Third public version V0.3 A lot of work in better code, some parts are documented in the code S0 Pulse counter logic added for logging use or production of electricity Send data to PV Output for production of electricity Extra fields for COSM.com for more information Ability to enable or disable certain functionality before deploying to Netduino PlusMCEBuddy 2.x: MCEBuddy 2.3.3: 1. MCEBuddy now supports PIPE (2.2.15 style) and the newer remote TCP communication. This is to solve problems with faulty Ceton network drivers and some issues with older system related to load. When using LOCALHOST, MCEBuddy uses PIPE communication otherwise it uses TCP based communication. 2. UPnP is now disabled by Default since it interferes with some TV Tuner cards (CETON) that represent themselves as Network devices (bad drivers). Also as a security measure to avoid external connection...Pulse: Pulse 0.6.2.0: This is a roll-up of a bunch of features I've been working on for a while. I wasn't planning to release it but Wallbase.cc is broken in any version earlier then this! - Fixed Wallbase.cc provider - Multi-provider options. Now you can specify multiple input providers with different search options. - Providers have little icons now - More! Check it out and report any bugs! Having issues? Check the Known Errors page for solutions to commonly encountered problems. If you don't see the ...Orchard Project: Orchard 1.6 RC: RELEASE NOTES This is the Release Candidate version of Orchard 1.6. You should use this version to prepare your current developments to the upcoming final release, and report problems. Please read our release notes for Orchard 1.6 RC: http://docs.orchardproject.net/Documentation/Orchard-1-6-Release-Notes Please do not post questions as reviews. Questions should be posted in the Discussions tab, where they will usually get promptly responded to. If you post a question as a review, you wil...Rawr: Rawr 5.0.1: This is the Downloadable WPF version of Rawr!For web-based version see http://elitistjerks.com/rawr.php You can find the version notes at: http://rawr.codeplex.com/wikipage?title=VersionNotes Rawr Addon (NOT UPDATED YET FOR MOP)We now have a Rawr Official Addon for in-game exporting and importing of character data hosted on Curse. The Addon does not perform calculations like Rawr, it simply shows your exported Rawr data in wow tooltips and lets you export your character to Rawr (including ba...Yahoo! UI Library: YUI Compressor for .Net: Version 2.1.1.0 - Sartha (BugFix): - Revered back the embedding of the 2x assemblies.Visual Studio Team Foundation Server Branching and Merging Guide: v2.1 - Visual Studio 2012: Welcome to the Branching and Merging Guide What is new? The Version Control specific discussions have been moved from the Branching and Merging Guide to the new Advanced Version Control Guide. The Branching and Merging Guide and the Advanced Version Control Guide have been ported to the new document style. See http://blogs.msdn.com/b/willy-peter_schaub/archive/2012/10/17/alm-rangers-raising-the-quality-bar-for-documentation-part-2.aspx for more information. Quality-Bar Details Documentatio...D3 Loot Tracker: 1.5.5: Compatible with 1.05.Common Data Parameters Module: CommonParam0.3H: Common Param has now been updated for VS2012 and NUnit 2.6.1. Conformance with the latest StyleCop has been maintained. If you need a version for VS2010, please use the previous version.????: ???_V2.0.0: ?????????????Write Once, Play Everywhere: MonoGame 3.0 (BETA): This is a beta release of the up coming MonoGame 3.0. It contains an Installer which will install a binary release of MonoGame on windows boxes with the following platforms. Windows, Linux, Android and Windows 8. If you need to build for iOS or Mac you will need to get the source code at this time as the installers for those platforms are not available yet. The installer will also install a bunch of Project templates for Visual Studio 2010 , 2012 and MonoDevleop. For those of you wish...WPUtils: WPUtils 1.3: Blend SDK for Silverlight provides a HyperlinkAction which is missing in Blend SDK for Windows Phone. This release adds such an action which makes use of WebBrowserTask to show web page. You can also bind the hyperlink to your view model. NOTE: Windows Phone SDK 7.1 or higher is required.Windawesome: Windawesome v1.4.1 x64: Fixed switching of applications across monitors Changed window flashing API (fix your config files) Added NetworkMonitorWidget (thanks to weiwen) Any issues/recommendations/requests for future versions? This is the 64-bit version of the release. Be sure to use that if you are on a 64-bit Windows. Works with "Required DLLs v3".CODE Framework: 4.0.21017.0: See change log in the Documentation section for details.Magelia WebStore Open-source Ecommerce software: Magelia WebStore 2.1: Add support for .net 4.0 to Magelia.Webstore.Client and StarterSite version 2.1.254.3 Scheduler Import & Export feature (for Professional and Entreprise Editions) UTC datetime and timezone support .net 4.5 and Visual Studio 2012 migration client magelia global refactoring release of a nugget package to help developers speed up development http://nuget.org/packages/Magelia.Webstore.Client optimization of the data update mechanism (a.k.a. "burst") Performance improvment of the d...JayData - The cross-platform HTML5 data-management library for JavaScript: JayData 1.2.2: JayData is a unified data access library for JavaScript to CRUD + Query data from different sources like OData, MongoDB, WebSQL, SqLite, HTML5 localStorage, Facebook or YQL. The library can be integrated with Knockout.js or Sencha Touch 2 and can be used on Node.js as well. See it in action in this 6 minutes video Sencha Touch 2 example app using JayData: Netflix browser. What's new in JayData 1.2.2 For detailed release notes check the release notes. Revitalized IndexedDB providerNow you c...VFPX: FoxcodePlus: FoxcodePlus - Visual Studio like extensions to Visual FoxPro IntelliSense.Droid Explorer: Droid Explorer 0.8.8.8 Beta: fixed the icon for packages on the desktop fixed the install dialog closing right when it starts removed the link to "set up the sdk for me" as this is no longer supported. fixed bug where the device selection dialog would show, even if there was only one device connected. fixed toolbar from having "gap" between other toolbar removed main menu items that do not have any menus Fiskalizacija za developere: FiskalizacijaDev 1.0: Prva verzija ovog projekta, još je uvijek oznacena kao BETA - ovo znaci da su naša testiranja prošla uspješno :) No, kako mi ne proizvodimo neki software za blagajne, tako sve ovo nije niti isprobano u "realnim" uvjetima - svaka je sugestija, primjedba ili prijava bug-a je dobrodošla. Za sve ovo koristite, molimo, Discussions ili Issue Tracker. U ovom trenutku runtime binary je raspoloživ kao Any CPU za .NET verzije 2.0. Javite ukoliko trebaju i verzije buildane za 32-bit/64-bit kao i za .N...Squiggle - A free open source LAN Messenger: Squiggle 3.2 (Development): NOTE: This is development release and not recommended for production use. This release is mainly for enabling extensibility and interoperability with other platforms. Support for plugins Support for extensions Communication layer and protocol is platform independent (ZeroMQ, ProtocolBuffers) Bug fixes New /invite command Edit the sent message Disable update check NOTE: This is development release and not recommended for production use.New ProjectsADFS 2.0 Attribute Store for SharePoint: ADFS 2.0 Attribute Store for SharePointALM Kickstarter: A simple Application Lifecycle Management Kickstart application written using ASP.NET MVC.Building iOS Apps with Team Foundation Server: An iPad sample project used for building iOS Xcode projects using a Team Foundation Server and the open source Jenkins build system. gyk-note: WTFHello World Fkollike: Test Project for fkollikeInnovacall ASP.net MVC 4 Azure Framework: Windows Azure Version of Innocacall ASP.net MVC 4 Framework. Intercom.Net: Intercom.Net is a C# library that provides easy tracking of customers to integration with the intercom.io CRM application. No need to learn yet another trackingjosephproject1: creating my first projectJust4Test: The project is just created for test.KBCruiser: KBCruiser helps developer to search reference or answers according to different resource categories: Forum/Blog/KB/Engine/Code/Downloadkp: store usernames/passwords from the commandline. ** Semi-secure, but by no means robust enough for production usage ** Troy Hunt would be disgusted.Neuron Operating System: Neuron Operating Systemnewelook: onesearch Pedestrian Simulation: Pedestrian simulationPTE: Using template Excel to generate UI for Prototyping.RequestModel: RequestModel is a simple implementation of typed access to a ASP.NET web forms request parametersSap: Sap is free, open-source web software that you can use to create a blog. Sap is made in ASP.NET MVC 4 (Razor). Sap is still pre-alpha and heavily in developmentSgart SharePoint 2010 Query Viewer: Windows application, based on the client object model of SharePoint 2010, that allows you to see the CAML query of a list view. Silverlight SuperLauncher: The Silverlight SuperLauncher project base on SL8.SL an Micosoft NESL.SL8.SL: The SL8.SL is a set of extension for silverlight. include mvvm,data validate,linq to sql, custom data page,oob helper etc. SL8.SL make easier to develop sl appSPDeployRetract: Easily Deploy and Retract SharePoint solutions using PowerShell. System Center Service Manager API: This API is for System Center Service Manager. It is written in C# and abstracts the more difficult aspects of service manager customization.TestingConf Utilities: This Framework will be helpful for testing and configuration purpose, so it has some methods that will be used as utilities that developers may need.The Veteran's Image Memory: his Project is been built for Educational purposes only . its not our Intention to offend anyone.Viking Effect: Viking Effect is a Brazilian website for the nerd people. We will offer news, tales and the Viking Scream, our take on the Podcast.Weather Report Widget: WPF-based application for displaying temperature, wind direction and speed for the selected city.WorldsCricket: WorldsCricket is a website which gives information on Cricket history with different cricket format, World’s cricketers, International Cricket Teams etc...XendApp - API: XendApp is a eco system for sending messages from a computer/application to a device. A device could be a phone or tablet for example.

  Read the article

• CodePlex Daily Summary for Wednesday, April 04, 2012

  CodePlex Daily Summary for Wednesday, April 04, 2012Popular ReleasesExtAspNet: ExtAspNet v3.1.2: ExtAspNet - ?? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ?????????? ExtAspNet ????? ExtJS ??? ASP.NET 2.0 ???，????? AJAX ??????????。 ExtAspNet ??????? JavaScript，?? CSS，?? UpdatePanel，?? ViewState，?? WebServices ???????。 ??????: IE 7.0, Firefox 3.6, Chrome 3.0, Opera 10.5, Safari 3.0+ ????：Apache License 2.0 (Apache) ??：http://extasp.net/ ??：http://bbs.extasp.net/ ??：http://extaspnet.codeplex.com/ ??：http://sanshi.cnblogs.com/ ????： +2012-04-04 v3.1.2 -??IE?????????????BUG（??"about:blank"?...totalem: version 2012.04.04.1: devel releaseNShape - .Net Diagramming Framework for Industrial Applications: NShape 2.0.0: Changes in 2.0.0:New / Changed / Extended Interfaces: public interface ISecurityManager public interface ISecurityDomainObject public interface IModelObject : ISecurityDomainObject public interface ILayerCollection : ICollection<Layer> public interface IRepository public interface ICommand public interface IModelMapping For details on interface changes, see documentation. For more changes on namespaces and base classes, see ReadMe.txt (installation folder) or Changes.txt in the s...ClosedXML - The easy way to OpenXML: ClosedXML 0.65.1: Aside from many bug fixes we now have Conditional Formatting The conditional formatting was sponsored by http://www.bewing.nl (big thanks) New on v0.65.1 Fixed issue when loading conditional formatting with default values for icon setsnopCommerce. Open source shopping cart (ASP.NET MVC): nopcommerce 2.50: Highlight features & improvements: • Significant performance optimization. • Allow store owners to create several shipments per order. Added a new shipping status: “Partially shipped”. • Pre-order support added. Enables your customers to place a Pre-Order and pay for the item in advance. Displays “Pre-order” button instead of “Buy Now” on the appropriate pages. Makes it possible for customer to buy available goods and Pre-Order items during one session. It can be managed on a product variant ...SkyDrive Connector for SharePoint: SkyDriveConnector for SharePoint: SkyDriveConnector for SharePointWiX Toolset: WiX v3.6 RC0: WiX v3.6 RC0 (3.6.2803.0) provides support for VS11 and a more stable Burn engine. For more information see Rob's blog post about the release: http://robmensching.com/blog/posts/2012/4/3/WiX-v3.6-Release-Candidate-Zero-availableSageFrame: SageFrame 2.0: Sageframe is an open source ASP.NET web development framework developed using ASP.NET 3.5 with service pack 1 (sp1) technology. It is designed specifically to help developers build dynamic website by providing core functionality common to most web applications.Lightbox Gallery Module for DotNetNuke: 01.11.00: This version of the Lightbox Gallery Module adds the following features/bug fixes: Feature: Read image EXIF information Bug Fix: URL parsing bug for any folder provider Minimum System Requirements Please ensure that your environment meets or exceeds the following system requirements: DotNetNuke® Version 06.00.00 or higher SQL Server 2005 or later .Net Framework 3.5 SP1 or lateriTuner - The iTunes Companion: iTuner 1.5.4475: Fix to parse empty playlists in iTunes LibraryGoogleMap Control: Google Geocoder 1.3: Geo types changes to string type and GeoAddressType enum changes to static class with some known types as constants in order to resolve the problems with new and not defined geo types.Document.Editor: 2012.2: Whats New for Document.Editor 2012.2: New Save Copy support New Page Setup support Minor Bug Fix's, improvements and speed upsVidCoder: 1.3.2: Added option for the minimum title length to scan. Added support to enable or disable LibDVDNav. Added option to prompt to delete source files after clearing successful completed items. Added option to disable remembering recent files and folders. Tweaked number box to only select all on a quick click.MJP's DirectX 11 Samples: Light Indexed Deferred Rendering: Implements light indexed deferred using per-tile light lists calculated in a compute shader, as well as a traditional deferred renderer that uses a compute shader for per-tile light culling and per-pixel shading.Pcap.Net: Pcap.Net 0.9.0 (66492): Pcap.Net - March 2012 Release Pcap.Net is a .NET wrapper for WinPcap written in C++/CLI and C#. It Features almost all WinPcap features and includes a packet interpretation framework. Version 0.9.0 (Change Set 66492)March 31, 2012 release of the Pcap.Net framework. Follow Pcap.Net on Google+Follow Pcap.Net on Google+ Files Pcap.Net.DevelopersPack.0.9.0.66492.zip - Includes all the tutorial example projects source files, the binaries in a 3rdParty directory and the documentation. It include...Extended WPF Toolkit: Extended WPF Toolkit - 1.6.0: Want an easier way to install the Extended WPF Toolkit?The Extended WPF Toolkit is available on Nuget. What's in the 1.6.0 Release?BusyIndicator ButtonSpinner Calculator CalculatorUpDown CheckListBox - Breaking Changes CheckComboBox - New Control ChildWindow CollectionEditor CollectionEditorDialog ColorCanvas ColorPicker DateTimePicker DateTimeUpDown DecimalUpDown DoubleUpDown DropDownButton IntegerUpDown Magnifier MaskedTextBox MessageBox MultiLineTex...Media Companion: MC 3.434b Release: General This release should be the last beta for 3.4xx. If there are no major problems, by the end of the week it will upgraded to 3.500 Stable! The latest mc_com.exe should be included too! TV Bug fix - crash when using XBMC scraper for TV episodes. Bug fix - episode count update when adding new episodes. Bug fix - crash when actors name was missing. Enhanced TV scrape progress text. Enhancements made to missing episodes display. Movies Bug fix - hide "Play Trailer" when multisaev...Better Explorer: Better Explorer 2.0.0.831 Alpha: - A new release with: - many bugfixes - changed icon - added code for more failsafe registry usage on x64 systems - not needed regfix anymore - added ribbon shortcut keys - Other fixes Note: If you have problems opening system libraries, a suggestion was given to copy all of these libraries and then delete the originals. Thanks to Gaugamela for that! (see discussion here: 349015 ) Note2: I was upload again the setup due to missing file!MonoGame - Write Once, Play Everywhere: MonoGame 2.5: The MonoGame team are pleased to announce that MonoGame v2.5 has been released. This release contains important bug fixes, implements optimisations and adds key features. MonoGame now has the capability to use OpenGLES 2.0 on Android and iOS devices, meaning it now supports custom shaders across mobile and desktop platforms. Also included in this release are native orientation animations on iOS devices and better Orientation support for Android. There have also been a lot of bug fixes since t...Circuit Diagram: Circuit Diagram 2.0 Alpha 3: New in this release: Added components: Microcontroller Demultiplexer Flip & rotate components Open XML files from older versions of Circuit Diagram Text formatting for components New CDDX syntax Other fixesNew ProjectsASP.Net MVC Composite Application Framework: ASP.NET MVC Composite Application FrameworkaTimer : Take a break timer: This timer will help programmers and other people who work on computer for long periods, users will be able to set their time period for work and break, whether you want to enforce the break by hibernating or making your computer sleep. Will be good for eyes, a lot! Still under development and will be monthly revised.Avilander Maven: Projeto Disciplina Branquinho.Banner from Databases: make a banner from database informationCrmXpress OptionSet Manager For Microsoft Dynamics CRM 2011: CrmXpress OptionSet Manager For Microsoft Dynamics CRM 2011CSharpCodeLineCounter: Count code lines as Code Metrics do.Decatec Sharepoint code: Various Decatec Sharepoint codeDevWebServer: DevWebServer is a simple, lightweight web server which can be used for unit testing HTTP client applications. It is developed in C#, has minimal dependencies and is provided as a single assembly.Effect Architect: A real-time effect editor (currently) aimed at Direct3D9. The idea is to bring features that popular IDEs provide to HLSL coding, as well as features that are specific to graphical coding.Gpu Hough: Demo project performing Hough transformation on GPUHappyHourWin8: This project contains several Metro-App development approaches. There will be an RSS-Reader, a task list and a game. Home Media Center: Home Media Center is a server application for UPnP / DLNA compatible devices. It supports streaming and transcoding media files, Windows desktop and video from webcams. This project is developed in C#, C++ and uses DirectShow, Media Foundation.INSTEON Mayhem Module: INSTEON module for Mayhem application.ISService: ISServiceKEITH: Kinect for hospitalsKnowledge Exchange: KnowledgeExchangeLightweight Test Automation Framework: The Lightweight Test Automation Framework for ASP.NET was developed and is currently used by the ASP.NET QA Team to automate regression tests for the product. It is designed to run within an ASP.NET application. Tests can be written in any .NET Framework language. They use an APlinewatchdk: linewatchdkLuaForMono: c#?lua?????,??LuaInterface??luaSharp???,?????????(luaInterface)??lua??c#?????????(luasharp),??mono?linux????????lua??.Metro App Toolkit: The Metro App Toolkit provides the developer community with key components and functionality that are commonly used in Metro Apps for WindowsPhone, Windows8 and the web, including Networking! Toolkit releases include samples & docs. From the community, for the community. My IE Accelerators: 1. dict.cn ie accelaratorofm: ofmOrchard Clippy module: Orchard Clippy moduleOrchard Twitter module: Orchard Twitter modulePersian Subtitle For Programming Courses: This project is created for collecting all programming course's PERSIAN SUBTITLE and help Persian language student to learn programming and every thing related to their major, by Meysam Hooshmandpicking: pickingPomodoro Timer for Visual Studio: Keep track of your Pomodoro Technique (from the Pomodoro Technique® official website – www.pomodorotechnique.com) sessions in Visual Studio.ScriptSafe: A simple powershell wrapper around source control aimed at admins to enable simple source control for their scripts.SkyDrive Connector for SharePoint: SkyDrive Connector for SharePoint is a sandbox web part that can help manage documents stored on skydrive on sharepoint by adding additional metadata. This helps the document to be discoverable on SharePoint. Also SkyDrive provides 25GB for free space for live users.SkypeTranslator: Help users to translate incoming message from Skype and Outlook applications to specified language. In core was use Elysium , log4net , and WPF frameworks, WPF Toolkit Extended,TPL,WCFTalking Heads: The TalkingHeads is a simple social network written in ASP .NET 4.0. It is intended for demonstrating and exploring application monitoring features of AVIcode technology. It works great with AVIcode 5.7, as well as with APM feature in System Center 2012. Unik Project: Unik is a Unified Framework makes easier to create enterprise .NET applications based on architecture best practice.WV-CU950 System Controller .NET Library.: WV-CU950 System Controller .NET library for Panasonic WV-CU950 System Controller. This library contains data processing method.YO JACK!: <Project name>Yo Jack!</Project name> Gather evidence to track down a physical theft of your computer, and turn over to the police. Free to the public.???????: ???????？

  Read the article

< Previous Page | 1 2 3 4 5