Search Results

Search found 8923 results on 357 pages for 'wireless keyboard'.

Page 5/357 | < Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

• Ubuntu 12.10, Wireless not working

  - by Karthik

  My Laptop is Acer 5742G with "Npilfy 802.11 wireless". I have both windows 7 and Ubuntu 12.10 Earlier when I had Ubuntu 12.04, the wireless was working fine, but after installing 12.10 wireless is not working at all, although it is still working in windows. I am not able to see "Wireless Networks" in the Network Manager nor in the Network Settings. This was the output I got for rfkill 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: acer-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 2: hci0: Bluetooth Soft blocked: no Hard blocked: no This is a snapshot of my Additional Drivers settings. As you can see, the required driver for wireless is installed.

  Read the article

• 12.04 drops Wired Network if Wireless connects

  - by mitt10tim

  This is a little different then most of the questions I have seen here. When I am at my office I keep my Lenovo Thinkpad t61p running Ubuntu 12.04 x64 connected via wired Ethernet. I also typically leave the wireless radios on. After a recent update the behavior of laptop in regards to the networks has changed. It used to be that if the laptop had a wired connection, the wired would supersede the wireless. Now, when I get to work and plug the laptop in and power it up, it connects via wired (correct behavior), shortly after the wireless begins searching for its favorite network (also correct) but as soon as it finds a network to connect to, I lose Internet. If I disconnect from the wireless network, leaving the wireless radios powered on, and refresh the wired connection, all is well again. Powering down the wireless radios also corrects the problem. How can I set this up so that the wired network (if available) always has precedence over the wireless?

  Read the article

• How do I get keyboard to write hiragana instead of katakana?

  - by Lisandro

  I added the Japanese Layout in Keyboard preferences, however all the layouts look like being in katakana. I suspect that the key that is left of number 1 (above Tab and under Esc) could be the one to switch from katakana to hiragana however I don't have that key in my keyboard and my other Toshiba laptop does not have it either. I really don't know what to do, I simply want to be able to write in hiragana in Ubuntu. Thanks

  Read the article

• Internet access using Edimax BR-6204WG as NIC

  - by Mat Richardson

  My internet access at home is provided by Virgin Media via their superhub. I have a laptop with no NIC - however I do have a spare wireless router, the Edimax BR-6204WG, which I have been led to believe can be used to bridge wireless connections. Only problem is, I'm not sure how to go about doing this. The manual for the device is here:- http://www.edimax.co.uk/images/Image/manual/Wireless/BR-6204Wg/BR-6204Wg_Manual.pdf Basically, I want to be able to connect the Edimax wireless router to my laptop using ethernet cable and to use it to pick up the wireless connection from my Virgin superhub. I've managed to get so far in some ways, but then I'm stuck.

  Read the article

• What is causing my internet to be slow on one laptop but not the other and only at a distance?

  - by Matt Case

  I have a newer laptop, purchased within the last year (acer aspire 7740). This laptop does not have any problem connecting to wireless networks and indicates that the signal strength is excellent on most of the wireless networks I connect to. When the laptop is within 10 feet of my wireless router it gets 30 down 10 up. When it is farther away than 10 feet it will be lucky to get 3 down and 1 up. I also have an older laptop, purchased in 2005, that has no problems at all at the same range. None of my phones, gaming consoles or tablets have this problem. I am beginning to think that the problem must be some hardware defect with the wireless card. I can provide additional information if needed. Just thought I'd check to see what others thought because I've been working on computers my whole life and have never heard of this happening. I have also tried to change the channels on my wireless router and have had no success with this idea.

  Read the article

• Android emulator doesn't take keyboard input from my desktop keyboard - SDK tools rev 20

  - by qhdwangnan

  After updating SDK tools rev to 20, Android emulator doesn't take keyboard input from my desktop keyboard. When press a key of the desktop keyboard, the emulator will dead and I have to kill its process. Android emulator also didn't take keyboard input from emulator own keyboard. But I have fixed this by following the steps in Android emulator doesn't take keyboard input - SDK tools rev 20. Does anyone have some suggestions?

  Read the article

• How do I get a Wireless N PCi card to connect to a wireless G router?

  - by Andy

  I'm having some problems setting up a new wireless PCI card on a WinXP SP3 PC. I know that the router is configured correctly. It is a Linksys WRT54GL, using 802.11b/g. Security mode is WPA2 Personal with TKIP+AES encryption. I am able to connect to this fine using my laptop (first gen MacBook with a 802.11b built in card). The new PCI card is also Linksys, but it supports 802.11n. Card seems to be installed ok (Windows sees it fine, doesn't list any errors in Device Manager), however when it scans for available wireless networks it can't find my wireless network (the router is set to broadcast the SSID). I tried to enter the network SSID manually, but that didn't seem to help. I chose WPA2-PSK for network authentication. The only options for encryption are TKIP or AES - I've tried both, neither worked. I am sure that I typed in my wireless key correctly. At this point, I don't think the problem is with encryption, but something else. It almost seems like I need to switch the wireless card into g mode, but I haven't found a way to do that (if that is even possible/necessary - I thought n was fully backwards compatible with g). Also, the PC is in the same room as the router, and my laptop, so I don't think that it is an interference issue. Any ideas what I'm doing wrong? I'm running out of things to try at this point. :(

  Read the article

• Wireless Repeating with two Netgear N750 (WNDR4300)

  - by jomo1911

  I have a Netgear N750 as my main router, which connects to the internet via a modem. I have a second Netgear N750 which I want to use to repeat the wireless signal of the main router. I logged in to routerlogin of my main router (192.168.1.1) and set up the "Wireless Repeating Function". I set it as the "Wireless Base Station" and filled in the MAC adress of my second Netgear N750. Then I logged in to routerlogin of my second router and set it up as the "Wireless Repeater", I gave it the IP 192.168.1.11 and filled in the MAC adress of the base station. During the setup of the second router (Repeater) I had to disable all security functions. If I connect to the repeaters' WLAN signal, I get no internet connection. Maybe you can help me, thanks

  Read the article

• Ubuntu: On-screen keyboard

  - by Paul Lammertsma

  On a similar note to this question, I recently booted Ubuntu to recover a Windows partition, but couldn't in any way get the keyboard to register. I recall back in 8.x that you could easily reach the on-screen keyboard (Virtual Keyboard?) via "Assistive Technologies". It seems to have disappeared since 9.x. For future reference, how can I easily get to it? Recall that in this scenario I won't have a keyboard to enter terminal commands (e.g. to install xkbd or something of the like).

  Read the article

• PS/2 and USB Keyboard is not working !!

  - by Mr-Right

  hello, let me make is clear that it is a different question from other related questions already posted here. Here is the scenario,No OS is installed in Computer. I am trying to install windows xp professional but due to keyboard failure I can't make it. PS/2 keyboard is not working at all. USB keyboard is working only before POST,I can work in BIOS. As soon as it starts booting from CD disc,keyboard fails to respond. And I can't go ahead from this message Press any key to boot from CD......

  Read the article

• How do you customize Excel 2010 keyboard shortcuts?

  - by Sam

  How do you customize Excel 2010 keyboard shortcuts? This article from microsoft.com provides instructions for "Microsoft Office 2010" but seems only apply to Word, not Excel. http://www.microsoft.com/athome/organization/compshortcuts.aspx In Microsoft Office 2010: Click the File tab to open Backstage view, and then click Options. Click Customize Ribbon and then, next to the Keyboard Shortcuts heading, click Customize. You can enter the new key combination here. Here's the dialog it points to shown in Word: But here's the same dialog shown in Excel: Notice it looks almost exactly the same but no "Keyboard Shortcuts: Customize.." button. So how do you customize the keyboard shortcuts in Excel?

  Read the article

• Keyboard in Oracle VirtualBox

  - by marc_s

  My buddy is running Oracle VirtualBox, and everything works fine - except for the fact that the backslash ( \ ) key on a Swiss-German keyboard doesn't work - instead you're getting a vertical bar ( | ) - which is really quite annoying if you're trying to type in UNC paths.... The \ on a Swiss-German keyboard is on the key with the < and > signs - you need to press Alt Gr or Alt+Ctrl to get it. Is there any way to teach VirtualBox that we're using a Swiss German keyboard and that it should respect the keyboard layout??

  Read the article

• Logitech MX3200 keyboard stopped working

  - by Roy Rico

  I have a Logitech MX3200 wireless keyboard and mouse set, and keyboard stopped working. I was working with it and it just stopped in the middle of using it. Some notes: The mouse still works flawlessly, i've tried to reconnect the KB i've tried to reconnect everything, mouse reconnects, keyboard reconnects (or pretends to) I've tried to hard reset (holding the connect button on the receiver for 10 seconds). I've tried new batteries I took out the batteries out of the KB & Mouse and unplugged the receiver over night. The media keys still work (launches winamp) but they main keys does not At this point, i've tried everything I've seen online. I just want to know is my keyboard dead in the water? I would say it's been about 8 months to a year since i've bought it, and the articles i find on the internet all say that's as long as they last... is this true? what's everyone's experience? I hope it's not true.

  Read the article

• Using keyboard specific keyboard-layouts in OS X

  - by Patrick O'Doherty

  I use a Kinesis Advantage with my MacBook Pro. While I use the dvorak layout when using the MBP's built-in keyboard the Kinesis has its own internal dvorak mode which assumes the host computer is using QWERTY. Is it possible to have OS X change the keyboard layout depending on which keyboard is currently being used? As far as I am aware this is possible on linux systems with HAL support but I haven't been able to find any support docs for OSX that advertise this ability. Thanks!

  Read the article

• Is there a way how to customize my keyboard layout in Xubuntu in a graphical way (by clicking)?

  - by Honza Javorek

  Possible duplicate, but I really couldn't find a solution. I would like to adjust my US keyboard layout, e.g. to add possibility to type some special characters on combination of right Alt + another character, etc. Moreover, my arrow up is dead, so until I buy another keyboard, I'd like to use my right shift as my arrow up, ASAP. However, there seems to be no way how to edit my keyboard layout easily in Xubuntu :( I found no editor and I really don't want to spend years in some configuration files and terminal (not that I can't, but I really really don't want). KLE - the only editor I could find, but no installation guide, no package, no PPA, no idea how to make it working (and uninstallable if not needed one day) Editor in Ubuntu - apparently not present in Xubuntu I found several tutorials how to change the layout, but they all seems to be complicated and not easy to follow. I don't want to spend a weekend in terminal or so, I am looking for an app to launch, make some clicking, finish my work by hitting Save button and - done! Please, is there such solution? For humans?

  Read the article

• Wireless is disabled by hardware switch on Dell Inspiron 1750

  - by lowerkey

  I have a problem where Ubuntu (12.04) says there is a wireless network card, but it is disabled by a hardware switch. How do I turn it on? I checked the BIOS, and the wireless card is enabled there. Fn + F2 was also no success. The results of rfkill list: 0: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: yes 1: dell-wifi: Wireless LAN Soft blocked: yes Hard blocked: yes sudo rfkill unblock wifi did nothing to the Wireless Status.

  Read the article

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• Mouse and keyboard not working after upgrading to 11.10

  - by geeehhdaa

  After upgrading to Ubuntu 11.10, neither my keyboard nor my mouse work anymore. The keyboard works during the boot process, but stops working as soon as the login screen appears. I'm stuck there because without a mouse or a keyboard I can't login or start a shell. If I hit ESC during startup to make the grub manager appear, the manager appears, but the keyboard won't work anymore. Mouse: Logitech RX 250, Keyboard: Cherry RS 6000

  Read the article

• Fedora 12 Wireless problems (Intel Wireless 4965AGN Card)

  - by Ninefingers

  Hi All, I'm having an interesting experience with my wireless card at the moment. Basically, it does like this: I connect to the local wireless network (netgear router) It works, briefly, allowing me to browse a webpage or maybe two, if I'm lucky. It then stops working / sending any packets, whilst reported still connected. Now, me being me I've had a look to see what I can find. wpa_supplicant.log looks like this: Trying to associate with valid_mac:a2:30 (SSID='vennardwireless' freq=2462 MHz) Associated with valid_mac:a2:30 WPA: Key negotiation completed with valid_mac:a2:30 [PTK=CCMP GTK=TKIP] CTRL-EVENT-CONNECTED - Connection to valid_mac:a2:30 completed (reauth) [id=0 id_str=] CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys So that's working fine. dmesg | grep "*iwl*" spits out this: iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds iwlagn: Copyright(c) 2003-2009 Intel Corporation iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 iwlagn 0000:03:00.0: setting latency timer to 64 iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 4965AGN REV=0x4 iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 19 802.11a channels iwlagn 0000:03:00.0: irq 32 for MSI/MSI-X phy0: Selected rate control algorithm 'iwl-agn-rs' iwlagn 0000:03:00.0: firmware: requesting iwlwifi-4965-2.ucode iwlagn 0000:03:00.0: loaded firmware version 228.61.2.24 Registered led device: iwl-phy0::radio Registered led device: iwl-phy0::assoc Registered led device: iwl-phy0::RX Registered led device: iwl-phy0::TX iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 iwlagn 0000:03:00.0: iwl_tx_agg_start on ra = 00:24:b2:32:a3:30 tid = 0 So that's working too. I can also ping 192.168.0.1 -I wlan0 and arping 192.168.0.1 -I wlan0 the router until the network falls over. uname -r:2.6.32.10-90.fc12.x86_64. Laptop is a Core2 Duo (2Ghz) with 3GB RAM. Other symptoms I've noticed are that wireshark freezes when I capture on the "broken" interface until I disconnect. Am using networkmanager as per normal. Stupidly, I can connect to the same router via eth0/a cat6 cable just fine. Everyone else can connect to the AP fine (from Windows). Yes, I'm sat right next to it and not trying to access a hotspot the other side of the world. Any ideas? Is this a broken update? (I intend to reboot and test an older kernel later)? Anyone else come across this? Edit: iwconfig wlan0 rate auto is the settings I'm using for rates. Also, according to networkmanager the network is still connected. Thanks for any pointers / advice.

  Read the article

• Wireless doesn't work on a Lenovo V570

  - by Stephen

  I've had Ubuntu installed on my HD for about 3 months but ever since I ran into this wireless issue I kinda lost my lust of Ubuntu. I have zero experience getting around with/ using the console command. I have a Lenovo V570. I got the driver update for the broadcom networking card via the Additional Drivers application but that did nothing. I love the look and feel of using Ubuntu but I have no technological experience for the matter. Any help would be awesome. When I scan for wireless connections while in Ubuntu, my computer picks up nothing, while on Win7 it will pick up the handful of wireless networks around my area. My wired connection is fine, but the use of not having wireless on a laptop is rather contradictory to it as a feature. Cheers! Also, I just installed 11.10, if that helps any. Yes, I used the search before I posted this, but again I have ZERO understanding of the command stuff and need a meat and potatoes answer(s). stephen@ubuntu:~$ sudo lshw -class network [sudo] password for stephen: *-network UNCLAIMED description: Network controller product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f1900000-f1903fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: 06 serial: f0:de:f1:63:98:14 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.1.78 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:f1804000-f1804fff memory:f1800000-f1803fff stephen@ubuntu:~$ rfkill list all 0: ideapad_wlan: Wireless LAN Soft blocked: yes Hard blocked: no 1: acer-wireless: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• [MINI HOW-TO] Create Keyboard Shortcuts to Applications in Windows

  - by Asian Angel

  Do you need just one or a few special keyboard shortcuts for your favorite program(s)? A quick modification to program shortcuts will get you up and running without installing additional software. Creating New Keyboard Shortcuts Go to the start menu shortcut for the program, right-click on it, and select properties. When the properties window opens click in the shortcut key text area. All that you need to do is choose an appropriate letter for the program (i.e. O for Opera, E for Editra, etc.) and type it in the blank. You will not need to type any other keys or combination in…the “Ctrl + Alt +” will be automatically entered for you as soon as you type the letter in. Click OK to finish creating the new keyboard shortcut. Those new keyboard shortcuts will speed up access to your favorite software. Another example from our system using “I” for Iron Browser. Certainly much quicker than using the start menu. Conclusion If you only need one or just a few special keyboard shortcuts then this method provides a quick and simple solution. Similar Articles Productive Geek Tips Show Keyboard Shortcut Access Keys in Windows VistaUse the Windows Key for the "Start" Menu in Ubuntu LinuxCreate Custom Windows Key Keyboard Shortcuts in WindowsHow-To Geek on Lifehacker: Control Your Computer with Shortcuts & Speed Up Vista SetupKeyboard Ninja: 21 Keyboard Shortcut Articles TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips CloudBerry Online Backup 1.5 for Windows Home Server Snagit 10 VMware Workstation 7 Acronis Online Backup Windows Firewall with Advanced Security – How To Guides Sculptris 1.0, 3D Drawing app AceStock, a Tiny Desktop Quote Monitor Gmail Button Addon (Firefox) Hyperwords addon (Firefox) Backup Outlook 2010

  Read the article

• How can I programmatically change the keyboard layout?

  - by Jason R. Coombs

  I want to run a shell command or script that will configure each of my Ubuntu Precise boxes to use the Dvorak keyboard layout as the default (and only) layout. With earlier versions, I was able to set the XKBVARIANT in /etc/default/keyboard but when I make this change in Precise (and reboot), the keyboard layout appears to be unaffected (both in console and in gnome). I tried also setting the XKBMODEL to pc105 and XKBLAYOUT to us, but that did not seem to help. I know I can set the layout for gnome using the 'keyboard layout' tool... but I want the change to affect the console, and I want to automate the process. How can I accomplish this? Edit: To clarify, I want to know how I can cause to change (using only a script or command-line) the keyboard layout to be Dvorak as the default and only keyboard layout for both Gnome and the console. I want this change to be persistent (survive reboots), just as it is when the change is made through the Keyboard Layout tool. Edit: Let me put it another way. If I had installed the operating system myself (which I did not because the OS was installed by the virtual machine infrastructure), I could have selected the desired keyboard layout at install time, and that layout would be applied persistently, system-wide. How can I change the layout to appear as if I had set it during the install process?

  Read the article

• Ubuntu 12.04 Freezes w/ Ethernet Unplugged + Wireless Drops (Acer Aspire 5516)

  - by Grand Master T

  Ubuntu 12.04-12.10 32/64 freezes or won't boot if the Ethernet cable is unplugged and will not hold a wireless connection. Here is my scenario... Laptop: Acer Aspire 5516 Wireless card: Broadcom BCM4312 Ubuntu 12.04 32/64 Issues Unity 3d won't load without the Ethernet cable plugged in. If I let it load with Ethernet plugged in, it will freeze once I disconnect the cable. Unity 2d will load without the Ethernet cable plugged. In Unity 2d, wireless cannot hold a connection. I can connect to a Wireless network, but when I try to use it (i.e. open a browser), it disconnects. I can reconnect by disabling wireless (uncheck Enable Wireless), re-enable wireless, and reconnect. But, it will disconnect again once I start using it. Ubuntu 12.10 Issues Since 12.10 only gives me the option to load 3d (I assume), I experience the same thing as the first issue in 12.04. Attempted Solutions Enable networking/LAN in BIOS Set LAN first in boot priority in BIOS Remove STA wireless driver (bcmwl-kernel-source) and install b43 low power driver (firmware-b43-lpphy-installer). Remove default Network Manager and install Wicd. So far, I have had no luck with fixing this issue. Does anyone have any further suggestions?

  Read the article

• Wireless problems with Broadcom BCM4313 with windows7 (duplicate)

  - by user292394

  I have wireless connection problem can't connect my wireless adress lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01) iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11abg ESSID:off/any Mode:Managed Access Point: Not-Associated Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off rfkill list all 0: hci0: Bluetooth Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: no 2: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no lsmod Module Size Used by bnep 19624 2 rfcomm 69160 8 ip6t_REJECT 12939 1 xt_hl 12521 6 ip6t_rt 13537 3 nf_conntrack_ipv6 18894 8 nf_defrag_ipv6 34768 1 nf_conntrack_ipv6 ipt_REJECT 12541 1 xt_LOG 17717 10 xt_limit 12711 13 xt_tcpudp 12884 18 xt_addrtype 12635 4 nf_conntrack_ipv4 15012 8 nf_defrag_ipv4 12758 1 nf_conntrack_ipv4 xt_conntrack 12760 16 ip6table_filter 12815 1 ip6_tables 27025 1 ip6table_filter nf_conntrack_netbios_ns 12665 0 nf_conntrack_broadcast 12589 1 nf_conntrack_netbios_ns nf_nat_ftp 12770 0 nf_nat 21798 1 nf_nat_ftp nf_conntrack_ftp 18638 1 nf_nat_ftp nf_conntrack 96976 8 nf_nat_ftp,nf_conntrack_netbios_ns,nf_nat,xt_conntrack,nf_conntrack_broadcast,nf_conntrack_ftp,nf_conntrack_ipv4,nf_conntrack_ipv6 iptable_filter 12810 1 ip_tables 27239 1 iptable_filter vx_tables 34059 13 ip6table_filter,xt_hl,ip_tables,xt_tcpudp,xt_limit,xt_conntrack,xt_LOG,iptable_filter,ip6t_rt,ipt_REJECT,ip6_tables,xt_addrtype,ip6t_REJECT uvcvideo 80885 0 videobuf2_vmalloc 13216 1 uvcvideo videobuf2_memops 13362 1 videobuf2_vmalloc snd_hda_codec_hdmi 46207 1 videobuf2_core 40664 1 uvcvideo videodev 134688 2 uvcvideo,videobuf2_core snd_hda_codec_conexant 57441 1 snd_hda_intel 52355 8 snd_hda_codec 192906 3 snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_hda_intel snd_hwdep 13602 1 snd_hda_codec snd_pcm 102099 4 snd_hda_codec_hdmi,snd_hda_codec,snd_hda_intel snd_page_alloc 18710 2 snd_pcm,snd_hda_intel snd_seq_midi 13324 0 dm_multipath 22873 0 snd_seq_midi_event 14899 1 snd_seq_midi scsi_dh 14882 1 dm_multipath lib80211_crypt_tkip 17619 0 snd_rawmidi 30144 1 snd_seq_midi intel_powerclamp 14705 0 coretemp 13435 0 kvm_intel 143060 0 kvm 451511 1 kvm_intel joydev 17381 0 serio_raw 13462 0 snd_seq 61560 2 snd_seq_midi_event,snd_seq_midi intel_ips 18664 0 wl 4207846 0 snd_seq_device 14497 3 snd_seq,snd_rawmidi,snd_seq_midi btusb 32412 0 bluetooth 395423 22 bnep,btusb,rfcomm snd_timer 29482 2 snd_pcm,snd_seq snd 69238 26 snd_hwdep,snd_timer,snd_hda_codec_hdmi,snd_hda_codec_conexant,snd_pcm,snd_seq,snd_rawmidi,snd_hda_codec,snd_hda_intel,snd_seq_device,snd_seq_midi lib80211 14381 2 wl,lib80211_crypt_tkip toshiba_bluetooth 12852 0 cfg80211 484040 1 wl lpc_ich 21080 0 fglrx 8085343 190 soundcore 12680 1 snd toshiba_acpi 22901 0 sparse_keymap 13948 1 toshiba_acpi wmi 19177 1 toshiba_acpi amd_iommu_v2 19054 1 fglrx video 19476 0 mei_me 18627 0 mei 82276 1 mei_me mac_hid 13205 0 parport_pc 32701 0 ppdev 17671 0 lp 17759 0 parport 42348 3 lp,ppdev,parport_pc hid_generic 12548 0 usbhid 52570 0 hid 106148 2 hid_generic,usbhid psmouse 102222 0 ahci 25819 3 libahci 32168 1 ahci atl1c 46086 0 dm_mirror 22135 0 dm_region_hash 20862 1 dm_mirror dm_log 18411 2 dm_region_hash,dm_mirror Can someone give any ideas on how I can fix my wireless

  Read the article

• What do the 4 keyboard input method systems in 10.04 mean?

  - by Android Eve

  I am trying to install another language support (in addition to the default US). Checking that language checkbox in "Install / Remove Languages..." wasn't too difficult. :) But now I want to add keyboard support, too, for that language. Again, I am prompted with a nice listbox with the following 4 options: none ibus lo-gtk th-gtk But I have no idea what these mean. I googled "ubuntu 10.04 keyboard input method system none ibus lo-gtk th-gtk" but all I could find was descriptions of problems, not an actual definition. Could you please point me to a webpage where I can learn about the meanings of these 4 different methods and +'s and -'s of each?

  Read the article

< Previous Page | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >