Search Results

Search found 2279 results on 92 pages for 'cable clutter'.

Page 50/92 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

• Intel Rapid Storage / Smart Response SSD caching issue

  - by goober

  Background Recently built my own PC. It works! Almost. It's been a while since getting into the guts of these things, so I'm familiar but may be missing something simple. FYI, I don't care about blowing the OS away -- it's brand new and we can go back from scratch as many times as necessary. Goal / Issue I'd like to use the SSD to take advantage of Intel's Smart Response technology (allows the SSD to act as a cache for HDDs) I would like the SSD cache to act as a cache for my HDDs, which I would like to be in a RAID1 array (so I get the speed from the SSD and the redundancy from the RAID1) However, Windows only sees the drive in device manager (not as a drive), so I'm unsure what to do about that. Related: as far as I know, for this to work, the drives all have to be in a single RAID array (i.e. a RAID0 pairing of the SSD and the RAID1 HDD array). However, when attempting this at the BIOS level, I am told there is not enough space for an array. Steps so Far Moved the SSD onto the Intel controller (I'd had it on the Marvel 6.0 controller instead of the Intel controller, so the BIOS was only seeing it in a strange way) Updated the BIOS of the motherboard to the latest version Reinstalled Intel's RST (iRST?) software several times, as some forums reported it working after reinstalling 3 times (which does not inspire confidence). Checked Intel storage: it does see the SSD as a physical, non-RAID device. However, it says no space exists if I try to create an array. Checked the BIOS: it does not show up in the boot order, but is an option that can be selected under boot options. Tried the firmware update for that model. Issue: the firmware CD doesn't detect a drive; maybe the Intel storage controller is making it difficult? moved the ssd to the marvel controller. The firmware update cd appeared to hang while searching for drives. swapped out the SATA cable for the manufacturer's and moved back to the intel storage controller. Noticed at this point that in the Intel RST software, a device DOES show up in addition to the RAID set -- only shown as a "60 GB internal disk". Windows doesn't appear to see it as a drive, but it does still show in device manager. Move SSD to port from 0-3 on MOBO and set SATA mode to IDE (after disconnecting RAID1 config) to allow the firmware update to work. Firmware was already at the latest version. Next Steps ? Components involved ASUS P8Z68-V PRO motherboard (Intel Z68 Chipset) Intel i7 2600k Processor 2 x 1TB 7200 RPM HDDs 64 GB Crucial M4 SSD (M4-CT064M4SSD2) For Reference -- Storage Configuration Intel 3 gbps Intel 3gbps Intel 6gbps Marvel 6gbps +----------+ +----------+ +----------+ +----------+ | | <----+ | | +-+ | | | |----------| | |----------| |-|--------| |----------| | | | | + | | | | | | +----------+ | +--|-------+ +-|--------+ +----------+ | | | + v v | 1 TB HDD 64 GB SSD + +> 1 TB HDD For Reference -- Intel RST (v10.8.0.1003) Screenshot Don't mind the "rebuilding" -- knocked a power cable out at one point; it's doing its job, not an indicator of a bad HDD. Any thoughts? Thanks in advance for any help!

  Read the article

• WNDR3700 Router + Cisco SG200-08 + LACP + Dual Uplink

  - by kobaltz

  Background I have a storage server that has several virtual machine images stored on them. I would store them locally, but I have limited space on my desktop (using SSD storage). I would like to increase the bandwidth between the desktop and the storage server by using two NICs on each computer. My original configuration allowed about 55MBps between the desktop and storage server. This storage server also has several TBs of documents, pictures, movies, vms, and ISO/programs. The storage server has 8 1.5TB hard drives in a RAID 10 configuration with a hardware RAID controller. The benchmarks on the RAID 10 are about 300MBps. Configuration In short, I am trying to bridge my switch and router. The switch is a small 8 port Cisco smart switch that supports 802.3ad LACP. I have two computers plugged into the switch, each with 2 Intel Gigabit NICs. The first computer is a Windows 7 machine that has the Intel ANS software installed. I have LACP configured with the computer and now show 3 NICs (2 Physical + 1 TEAM Virtual @ 2Gbps). It looks like this computer is configured correctly. I trunked the two ports that this computer is plugged into with the switch's web interface. The second computer is a homebrew storage box running debian. I also have the bonding enabled on this machine and the switch configured with LACP. Without having the WNDR3700 router in the picture yet, I am able to communicate between the Windows 7 machine and the debian box since they both have static IP addresses. With LACP enabled on both machines I am getting about 106-108MBps speeds. Issue I plug in a network cable from the switch into the router and enable DHCP on the desktop. I saw no need to have a static address on the desktop. My transfer rates are still from 106MBps-108MBps. While this is still a boost, I am trying to figure out how to get about 140-180MBps. I am thinking that I need to increase the bandwidth from the router to the switch. My switch allows 4 groups for port trunking. I plugged in a second network cable from the router to the switch. My question is, what is the proper way to fix this issue. Should I port trunk the two ports that are going from the switch to the router? Keep in mind that the router is a WNDR3700 and is unsure whether or not it supports LACP. I do have OpenWRT installed on the router, but it still wasn't clear in any documentation that I found if it supported 802.3ad LACP standards. I am also wondering if there needs to be anything changed within the Cisco settings. [Edit] - Corrected some numbers, wasn't really paying attention. It looks like the speeds though at least two NICs are bonded with LACP is still reaching the max bandwidth of one port. Is there a way to configure the switch so that I can increase this bandwidth? Also, on the storage server, I had a couple of extra NICs laying around and threw them on there as well. Another EDIT and More Findings I happened to look at the traffic of each individual NIC and think that I see the problem. I tested with a simple transfer for a 4GB file. I noticed that only one of the NICs was taking the load of the traffic. I then copied the file back to the Storage Server and noticed that the other NIC was sending out the traffic. I have 802.3ad LACP enabled on the two NICs and I see that it gets enabled dynamically on the switch's interface. Should I be using Static Link Aggregation?

  Read the article

• Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

  - by Jørgen

  I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

  Read the article

• How do I connect my Windows XP laptop to the internet?

  - by rubysiddhi

  Hello fellow super users, The Past I have a Acer Travelmate 2300 laptop running Windows XP. 6 months ago I moved into a new apartment and got a new internet connection set up. After getting an internet connection installed in my apartment I reinstalled Windows XP and at the same time wiped my drive clean losing all the original Acer software and drivers. Once XP was reinstalled I had to find all the drivers again to get the Travelmate laptop connected to the internet. So, using my Vista laptop which was connected fine, I went to the Acer Travelmate Series drivers download page to download the necessary drivers. I transferred them to my Acer XP machine and installed them the best I could (there were no easy instructions so I just had to find all the executables and run them). I eventually got connected to the internet but not exactly in the way I had hoped for. The Present To be connected to the internet I need to have an Ethernet cord connecting my computer (via the Ethernet port) to my router. This is a problem since it defeats the purpose of having a Wireless LAN card in my Acer laptop. One of the programs I downloaded from the Acer Travelmate Series page was the Acer Wireless LAN Configuration Utility. This program allows me to see the current network I am connected to and all the available networks I could potentially connect to. It reminds me of XP's Wireless Network Connection window/utility where you can see all available wireless networks, refresh the network list and connect to one of the networks. I should mention that my ISP set up a security enabled wireless network with WPA. This network requires a network key if you want to connect to it. I guess my Vista computer has the network key entered into it already. The problem is that I do not know what the network key is. Now obviously you would say just contact my ISP to get the key. And I will but there is just one extra weird issue. I am able to connect to another unsecured wireless network in the Wireless Network Connection window/utility. I can be on it as long as my Ethernet cable is plugged in. So this is not really wireless is it? And this indicates that even if I do get that network key password from my ISP, I will only solve one of the two problems I have. I will only solve being able to get online as long as I am connected to my router via the Ethernet cable. The Main Questions So how do I enable my acer IPN2220 Wireless LAN Card so that I can use my Acer laptop from anywhere with in my apartment? Or should I first get the network key from my ISP to access my security enabled wireless network? And then deal with getting the acer IPN2220 Wireless LAN Card working? Hard & Learned VS Easy & Stupid Of course contacting the ISP would be easier. Have em just come in here and do there thing. The problem with that is that they do not speak English (yeah, im in Poland) and it'd be a hell of a time trying to understand what they are doing (uncomfortable looking over their shoulder). Also, I want to learn how to do this task myself so that I can fix the problem if it ever happens again. You know, be more self sufficient. I look forward to helpful replies. Thanks, Xaviour

  Read the article

• What to Do When Windows Won’t Boot

  - by Chris Hoffman

  You turn on your computer one day and Windows refuses to boot — what do you do? “Windows won’t boot” is a common symptom with a variety of causes, so you’ll need to perform some troubleshooting. Modern versions of Windows are better at recovering from this sort of thing. Where Windows XP might have stopped in its tracks when faced with this problem, modern versions of Windows will try to automatically run Startup Repair. First Things First Be sure to think about changes you’ve made recently — did you recently install a new hardware driver, connect a new hardware component to your computer, or open your computer’s case and do something? It’s possible the hardware driver is buggy, the new hardware is incompatible, or that you accidentally unplugged something while working inside your computer. The Computer Won’t Power On At All If your computer won’t power on at all, ensure it’s plugged into a power outlet and that the power connector isn’t loose. If it’s a desktop PC, ensure the power switch on the back of its case — on the power supply — is set to the On position. If it still won’t power on at all, it’s possible you disconnected a power cable inside its case. If you haven’t been messing around inside the case, it’s possible the power supply is dead. In this case, you’ll have to get your computer’s hardware fixed or get a new computer. Be sure to check your computer monitor — if your computer seems to power on but your screen stays black, ensure your monitor is powered on and that the cable connecting it to your computer’s case is plugged in securely at both ends. The Computer Powers On And Says No Bootable Device If your computer is powering on but you get a black screen that says something like “no bootable device” or another sort of “disk error” message, your computer can’t seem to boot from the hard drive that Windows was installed on. Enter your computer’s BIOS or UEFI firmware setup screen and check its boot order setting, ensuring that it’s set to boot from its hard drive. If the hard drive doesn’t appear in the list at all, it’s possible your hard drive has failed and can no longer be booted from. In this case, you may want to insert Windows installation or recovery media and run the Startup Repair operation. This will attempt to make Windows bootable again. For example, if something overwrote your Windows drive’s boot sector, this will repair the boot sector. If the recovery environment won’t load or doesn’t see your hard drive, you likely have a hardware problem. Be sure to check your BIOS or UEFI’s boot order first if the recovery environment won’t load. You can also attempt to manually fix Windows boot loader problems using the fixmbr and fixboot commands. Modern versions of Windows should be able to fix this problem for you with the Startup Repair wizard, so you shouldn’t actually have to run these commands yourself. Windows Freezes or Crashes During Boot If Windows seems to start booting but fails partway through, you may be facing either a software or hardware problem. If it’s a software problem, you may be able to fix it by performing a Startup Repair operation. If you can’t do this from the boot menu, insert a Windows installation disc or recovery disk and use the startup repair tool from there. If this doesn’t help at all, you may want to reinstall Windows or perform a Refresh or Reset on Windows 8. If the computer encounters errors while attempting to perform startup repair or reinstall Windows, or the reinstall process works properly and you encounter the same errors afterwards, you likely have a hardware problem. Windows Starts and Blue Screens or Freezes If Windows crashes or blue-screens on you every time it boots, you may be facing a hardware or software problem. For example, malware or a buggy driver may be loading at boot and causing the crash, or your computer’s hardware may be malfunctioning. To test this, boot your Windows computer in safe mode. In safe mode, Windows won’t load typical hardware drivers or any software that starts automatically at startup. If the computer is stable in safe mode, try uninstalling any recently installed hardware drivers, performing a system restore, and scanning for malware. If you’re lucky, one of these steps may fix your software problem and allow you to boot Windows normally. If your problem isn’t fixed, try reinstalling Windows or performing a Refresh or Reset on Windows 8. This will reset your computer back to its clean, factory-default state. If you’re still experiencing crashes, your computer likely has a hardware problem. Recover Files When Windows Won’t Boot If you have important files that will be lost and want to back them up before reinstalling Windows, you can use a Windows installer disc or Linux live media to recover the files. These run entirely from a CD, DVD, or USB drive and allow you to copy your files to another external media, such as another USB stick or an external hard drive. If you’re incapable of booting a Windows installer disc or Linux live CD, you may need to go into your BIOS or UEFI and change the boot order setting. If even this doesn’t work — or if you can boot from the devices and your computer freezes or you can’t access your hard drive — you likely have a hardware problem. You can try pulling the computer’s hard drive, inserting it into another computer, and recovering your files that way. Following these steps should fix the vast majority of Windows boot issues — at least the ones that are actually fixable. The dark cloud that always hangs over such issues is the possibility that the hard drive or another component in the computer may be failing. Image Credit: Karl-Ludwig G. Poggemann on Flickr, Tzuhsun Hsu on Flickr     

  Read the article

• Iptables Forwarding problem

  - by ankit

  Hi all, I had initally asked question about sertting up my linux box for natting for my home network and was given suggestions in the thread here. Did not want to clutter the old question so starting a new one here. based on the earlier suggestions, i have come up with the following rules ... :PREROUTING ACCEPT [1:48] :OUTPUT ACCEPT [12:860] :POSTROUTING ACCEPT [3:228] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT *filter :INPUT DROP [3:228] :FORWARD DROP [0:0] :OUTPUT DROP [0:0] -A INPUT -i lo -j ACCEPT -A INPUT -i eth0 -p icmp -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 80 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 443 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 22 -j ACCEPT -A FORWARD -i eth1 -p icmp -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 80 -j ACCEPT -A FORWARD -i eth1 -p tcp -m tcp --dport 443 -j ACCEPT -A OUTPUT -p icmp -j ACCEPT -A OUTPUT -j ACCEPT COMMIT If you notice, i do have the proper MASQURADING rule and the proper FORWARD filter rule as well. However i am facing 2 problems On the linux box itself DNS resolving is not working the lan clients connected to the linux box, are still not able to get to internet. when i ping something from them, i see the DROP count in iptables INPUT rule increasing. now my question is, when i am pinging something from the lan client, how come it is being matched by the input chain ?! should it be in the forward chain ? Chain INPUT (policy DROP 20 packets, 2314 bytes) pkts bytes target prot opt in out source destination 99 9891 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- eth0 any anywhere anywhere 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:https 122 9092 ACCEPT tcp -- eth0 any anywhere anywhere tcp dpt:ssh Thanks ankit

  Read the article

• External USB HD with -optional- mains?

  - by Stephen

  Hi, I'm Christmas-present-buying, and I'd appreciate recommendations for a USB HD with an optional mains power input. I've hunted, but can't find all the information I want (partially due to sketchy product specifications). Background: This is for a digital TV which I do not own, and so I'd like to get it correct first time. The TV has a USB port to allow recording straight to disk, but the manuals don't say how much power can be drawn through the USB port. The manual's instructions state, possibly generically, to plug the drive in before connecting to the TV. Ideally I'd like a small (2.5"?) drive which can draw power over USB, with an mains power input if it turns out the USB port on the TV doesn't offer enough juice. The ideal is to use one cable, two max. A powered USB hub would introduce too much clutter. I've spotted that the LaCie Petit drives have what appears to be an additional power input, but I'm not even sure from the specs what that is. And the device doesn't ship with a mains adapter. Suggestions?

  Read the article

• Wireless networks are not detected at start up in Ubuntu 12.04

  - by Kanhaiya Mishra

  I have recently (three four days ago) installed Ubuntu 12.04 via windows installer i.e. wubi.exe. After the installation completed wireless and Ethernet were both working well. But after restart wireless networks didn't show up while in the network manager both networking and wireless were enabled. Though sometimes after boot it did show the networks available but very rarely. So I went through various posts regarding wireless issues in Ubuntu 12.04 and tried so many things but ended up in nothing satisfactory. I have Broadcom 4313 LAN network controller and brcmsmac driver. Then relying on some suggestions I tried to install bcm-wl driver but couldn't install due to some error in jockeyl.log file. Then i tried fresh installation of the same driver but still could resolve the startup issues with wireless. Then again I reinstalled Ubuntu inside windows using wubi installer. This time again same problem occurred after boot. But this time I successfully installed wl driver before disturbing file-system files of Ubuntu. But again the same issue. This time I noticed some new things: If I inserted Ethernet/LAN cable before startup then wireless networks are available and of course LAN(wired) networks also work. but if i don't plug in cable before startup and then plug it after startup then it didn't detect Ethernet network neither wireless. So I haven't noticed it before that LAN along with wifi also doesn't work after startup. But if i suspend the session and make it sleep and again login then it worked. I tried it every time that WLAN worked perfectly. But still i m unable to resolve that startup problem. Each time i boot first I have to suspend it once then only networks are available. It irritates me each time i reboot/boot my lappy. So please help out of this problem. Any ideas/help regarding this issue would be highly appreciated. Some of the commands that i run gave following results: # lspci 00:00.0 Host bridge: Intel Corporation Core Processor DRAM Controller (rev 12) 00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) 00:16.0 Communication controller: Intel Corporation 5 Series/3400 Series Chipset HECI Controller (rev 06) 00:1a.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1b.0 Audio device: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio (rev 06) 00:1c.0 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 (rev 06) 00:1c.1 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 (rev 06) 00:1c.5 PCI bridge: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 6 (rev 06) 00:1d.0 USB controller: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller (rev 06) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev a6) 00:1f.0 ISA bridge: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller (rev 06) 00:1f.2 SATA controller: Intel Corporation 5 Series/3400 Series Chipset 6 port SATA AHCI Controller (rev 06) 00:1f.3 SMBus: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller (rev 06) 00:1f.6 Signal processing controller: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem (rev 06) 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01) 04:00.0 Ethernet controller: Atheros Communications Inc. AR8152 v1.1 Fast Ethernet (rev c1) ff:00.0 Host bridge: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers (rev 02) ff:00.1 Host bridge: Intel Corporation Core Processor QuickPath Architecture System Address Decoder (rev 02) ff:02.0 Host bridge: Intel Corporation Core Processor QPI Link 0 (rev 02) ff:02.1 Host bridge: Intel Corporation Core Processor QPI Physical 0 (rev 02) ff:02.2 Host bridge: Intel Corporation Core Processor Reserved (rev 02) ff:02.3 Host bridge: Intel Corporation Core Processor Reserved (rev 02) # sudo lshw -C network *-network description: Wireless interface product: BCM4313 802.11b/g/n Wireless LAN Controller vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 01 serial: 70:f1:a1:49:b6:ab width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 ip=192.168.1.7 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:f0500000-f0503fff *-network description: Ethernet interface product: AR8152 v1.1 Fast Ethernet vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:04:00.0 logical name: eth0 version: c1 serial: b8:ac:6f:6b:f7:4a capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.0-NAPI firmware=N/A latency=0 link=no multicast=yes port=twisted pair resources: irq:44 memory:f0400000-f043ffff ioport:2000(size=128) # lsmod | grep wl wl 2568210 0 lib80211 14381 2 lib80211_crypt_tkip,wl # sudo iwlist eth1 scanning eth1 Scan completed : Cell 01 - Address: 30:46:9A:85:DA:9A ESSID:"BH DASHIR 2" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:4/5 Signal level:-60 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B000103104700109AFE7D908F8E2D381860668BA2E8D8771021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 02 - Address: C0:3F:0E:EB:45:14 ESSID:"BH DASHIR 3" Mode:Managed Frequency:2.462 GHz (Channel 11) Quality:2/5 Signal level:-71 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD7F0050F204104A00011010440001021041000100103B00010310470010F3C9BBE499D140540F530E7EBEDE2F671021000D4E4554474541522C20496E632E10230009574752363134763130102400095747523631347631301042000538333235381054000800060050F204000110110009574752363134763130100800020084 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s 24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s 12 Mb/s; 48 Mb/s Cell 03 - Address: A0:21:B7:A8:2F:C0 ESSID:"BH DASHIR 4" Mode:Managed Frequency:2.422 GHz (Channel 3) Quality:1/5 Signal level:-86 dBm Noise level:-98 dBm IE: IEEE 802.11i/WPA2 Version 1 Group Cipher : CCMP Pairwise Ciphers (1) : CCMP Authentication Suites (1) : PSK IE: Unknown: DD8B0050F204104A0001101044000102103B0001031047001000000000000010000000A021B7A82FC01021000D4E6574676561722C20496E632E10230009574E523130303076321024000456324831104200046E6F6E651054000800060050F20400011011001B574E5231303030763228576972656C6573732041502D322E344729100800020086103C000103 Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s 9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s 48 Mb/s; 54 Mb/s

  Read the article

• How can I get Haproxy to not log local requests?

  - by coneybeare

  I am trying to clean out some of the log clutter from my machines and am starting by removing requests that are generated from the server themselves. I have cache warmers running around the clock and I don't want these polluting the logs. I was able to get apache to stop logging local requests by adding a dontlog for the local IP: SetEnvIf Remote_Addr "RE\.DA\.CT\.ED" dontlog CustomLog "|logger -p local3.info -t http" combined env=!dontlog and now I am looking for something similar to put in a configuration for the Haproxy log. How can I prevent 127.0.0.1 requests from writing to the Haproxy log? UPDATE: 2/15/11 I use the excellent loggly service to pull out logs in the cloud, but I am seeing tons of logs like this: 2011 Feb 15 06:09:42.000 ip-10-251-194-96 http: RE.DA.CT.ED - - [15/Feb/2011:06:09:42 -0500] "HEAD /search/Nevad/predictive/txt HTTP/1.0" 200 - "-" "Wget/1.10.2 (Red Hat modified)" 2011 Feb 15 06:09:42.000 127.0.0.1 haproxy[10390]: 127.0.0.1:58408 [15/Feb/2011:06:09:42] www i-5dd7a331.0 0/0/0/8/8 200 210 - - --NI 0/0/0 0/0 "HEAD /search/Nevad/predictive/txt HTTP/1.1" and I want them gone. This question focuses on how to remove that haproxy log line from writing to the server side log in the first place.

  Read the article

• How to migrate WinXP from failing old HD to new one

  - by Péter Török

  Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

  Read the article

• DirectAccess client can't connect

  - by odd parity

  I've set up a DirectAccess server on Windows Server 2012 at my workplace. I'm using a Windows 8 Enterprise client to connect to it. It works fine over a mobile connection, but it fails when connecting from home. I've ruled out the firewall/router as the culprit as the issues persist when connecting the laptop directly to the cable modem. I'm not sure where to begin to debug this, does anyone have any pointers? Both Teredo and IPHTTPS interfaces are up (although as the server is behind a NAT and we only have 1 public IP I understand that IPHTTPS is the only protocol that will be used). The IPHTTPS tunnel also seems to be connected: netsh interface httpstunnel show interfaces Interface IPHTTPSInterface (Group Policy) Parameters ------------------------------------------------------------ Role : client URL : https://redacted:443/IPHTTPS Last Error Code : 0x0 Interface Status : IPHTTPS interface active however the DirectAccess link can't be activated - get-daconnectionstatus cycles between Status : Error Substatus : CouldNotContactDirectAccessServer and Status : Error Substatus : RemoteNetworkAuthenticationFailure Any suggestions on how to attack this are appreciated!

  Read the article

• Cisco ASA 5505 - L2TP over IPsec

  - by xraminx

  I have followed this document on cisco site to set up the L2TP over IPsec connection. When I try to establish a VPN to ASA 5505 from my Windows XP, after I click on "connect" button, the "Connecting ...." dialog box appears and after a while I get this error message: Error 800: Unable to establish VPN connection. The VPN server may be unreachable, or security parameters may not be configured properly for this connection. ASA version 7.2(4) ASDM version 5.2(4) Windows XP SP3 Windows XP and ASA 5505 are on the same LAN for test purposes. Edit 1: There are two VLANs defined on the cisco device (the standard setup on cisco ASA5505). - port 0 is on VLAN2, outside; - and ports 1 to 7 on VLAN1, inside. I run a cable from my linksys home router (10.50.10.1) to the cisco ASA5505 router on port 0 (outside). Port 0 have IP 192.168.1.1 used internally by cisco and I have also assigned the external IP 10.50.10.206 to port 0 (outside). I run a cable from Windows XP to Cisco router on port 1 (inside). Port 1 is assigned an IP from Cisco router 192.168.1.2. The Windows XP is also connected to my linksys home router via wireless (10.50.10.141). Edit 2: When I try to establish vpn, the Cisco device real time Log viewer shows 7 entries like this: Severity:5 Date:Sep 15 2009 Time: 14:51:29 SyslogID: 713904 Destination IP = 10.50.10.141, Decription: No crypto map bound to interface... dropping pkt Edit 3: This is the setup on the router right now. Result of the command: "show run" : Saved : ASA Version 7.2(4) ! hostname ciscoasa domain-name default.domain.invalid enable password HGFHGFGHFHGHGFHGF encrypted passwd NMMNMNMNMNMNMN encrypted names name 192.168.1.200 WebServer1 name 10.50.10.206 external-ip-address ! interface Vlan1 nameif inside security-level 100 ip address 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address external-ip-address 255.0.0.0 ! interface Vlan3 no nameif security-level 50 no ip address ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive dns server-group DefaultDNS domain-name default.domain.invalid object-group service l2tp udp port-object eq 1701 access-list outside_access_in remark Allow incoming tcp/http access-list outside_access_in extended permit tcp any host WebServer1 eq www access-list outside_access_in extended permit udp any any eq 1701 access-list inside_nat0_outbound extended permit ip any 192.168.1.208 255.255.255.240 access-list inside_cryptomap_1 extended permit ip interface outside interface inside pager lines 24 logging enable logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool PPTP-VPN 192.168.1.210-192.168.1.220 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-524.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface www WebServer1 www netmask 255.255.255.255 access-group outside_access_in in interface outside timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute http server enable http 192.168.1.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport crypto map outside_map 1 match address inside_cryptomap_1 crypto map outside_map 1 set transform-set TRANS_ESP_3DES_MD5 crypto map outside_map interface inside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! dhcpd address 192.168.1.2-192.168.1.33 inside dhcpd enable inside ! group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.1.1 vpn-tunnel-protocol IPSec l2tp-ipsec username myusername password FGHFGHFHGFHGFGFHF nt-encrypted tunnel-group DefaultRAGroup general-attributes address-pool PPTP-VPN default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key * tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! ! prompt hostname context Cryptochecksum:a9331e84064f27e6220a8667bf5076c1 : end

  Read the article

• Baseline 2952-SFP normal?

  - by Atlas

  I just installed a 3com 2952-sfp, and I had its port #48 connected to another gigabit switch through a cat5e cable. Now when I look at the logs, I see the lines shown below: Mar 23 11:20:15:829 2010 MSTP Critical PFWD Instance 0's GigabitEthernet1/0/48 has been set to forwarding state! Mar 23 11:20:15:822 2010 IFNET Warning LINK UPDOWN GigabitEthernet1/0/48: link status is UP Mar 23 11:20:12:974 2010 IFNET Warning LINK UPDOWN GigabitEthernet1/0/48: link status is DOWN The above happens like dozens of times per day, is there something wrong with my setup?

  Read the article

• Share openVPN connection

  - by Douglas Gemignani

  Hello, Currently I have a server (dev tun) running openVPN and my WinXP client is able to connect to the server just fine. I have an ethernet device and I need to send data to a computer under the server's network, so since the device can't connect on its own I need to configurate my Windows XP to share its VPN connection. So, on my WinXP machine i have: Network Adapter #1 (ip 192.168.0.2 gw 192.168.0.1 with internet access). OpenVPN Connection (dhcp). Network Adapter #2 (crossover cable with device). Here is my client.ovpn cert gertec.crt key gertec.key client ns-cert-type server user nobody group nobody remote IP PORT ca ca.crt dev tun dev-node OpenVPN proto udp resolv-retry infinite nobind comp-lzo verb 3 I would appreciate any help.

  Read the article

• Connecting Wii to router to Proxy Server via VPN to BBC iPlayer

  - by nkimber

  I live in the USA and want to be able to watch UK TV streamed over the web. The relevant services are geographically crippled. I can do this by using a VPN proxy server in the UK, connecting to the VPN service using a straight Windows VPN connection. However, this means I have to watch everything on my PC. The BBC iPlayer works on the Wii in the UK. So, I'd like to connect my Wii to a wireless router (LinkSys WRT54G2) and have that be automatically connected via VPN to my proxy service in the UK. If I can do this then I'd be able to stream UK TV direct to my TV via the Wii. I thought I could have one router act as my VPN connection, connected to a 2nd router that connects to my Cable internet access. But this bit isn't working, any thoughts?

  Read the article

• Mac OS can't connect to SMB shares after sleep

  - by Andreas

  I used to access my local Windows 2008 file server's SMB shares on my recent (3 weeks old) MacBook Pro without problems. However, for a few days now, it fails to (re-)connect to the server after it woke up from sleep mode. Finder just shows "connecting..." and hangs indefinitely. The same thing happens when I try it from the command line (mount -t smbfs). This happens via both WiFi and cable, I also tried turning networking off and back on. The only thing that helps is a reboot. Any hints?

  Read the article

• Cheap dvr media server

  - by Tester101

  I would like to build a new computer to be used as a DVR and media server. I am thinking of using mythtv as the DVR software, but short of that decision I am completely open to suggestions. Requirements: Must be cheap. Must have low power consumption (since it will always be on). Should be quiet. Should be small. I'm really not sure where to start with this project, and am open to any hardware/software suggestions. Is it possible to build a small quiet and cheap system? *Keep in mind I am working on this project because I am tired of Cable rate increases, but I can't imagine living without a DVR so cost is very important and I would like the system to be sub $200.00. The system also needs to handle the new digital broadcast system. Thanks for the help,

  Read the article

• "No bootable device - insert boot disk" after restart on Ubuntu 10.04 b1 update

  - by anjanesh

  I was making an update on my Ubuntu 10.04 beta1 64-bit PC when, after reboot I get PXE-E61: Mediaa test failure, check cable PXE-M0F: Exiting Intel Boot Agent. No bootable device - insert boot disk and press any key How did my boot record disappear ? BIOS Boot Boot Menu Type : Normal Boot Device Priority : <CD/DVD-ROM Drive> <Hard Disk Drive> <Floppy Drive> <Ethernet> Hard Driver Order : No Hard Disk Drive CD/DVD ROM Drive Order : <PT-TSSTcorp CDDV> Removable Drive Order : No Removable Drive Boot to Optical Devices : <Enable> Boot to Removable Devices : <Enable> Boot to Network : <Enable> USB Boot : <Enable>

  Read the article

• What does it mean when ARP shows <incomplete> on eth1

  - by Geoff Dalgas

  We have been using HAProxy along with heartbeat from the Linux-HA project. We are using two linux instances to provide a failover. Each server has with their own public IP and a single IP which is shared between the two using a virtual interface (eth1:1) at IP: 69.59.196.211 The virtual interface (eth1:1) IP 69.59.196.211 is configured as the gateway for the windows servers behind them and we use ip_forwarding to route traffic. We are experiencing an occasional network outage on one of our windows servers behind our linux gateways. HAProxy will detect the server is offline which we can verify by remoting to the failed server and attempting to ping the gateway: Pinging 69.59.196.211 with 32 bytes of data: Reply from 69.59.196.220: Destination host unreachable. Running arp -a on this failed server shows that there is no entry for the gateway address (69.59.196.211): Interface: 69.59.196.220 --- 0xa Internet Address Physical Address Type 69.59.196.161 00-26-88-63-c7-80 dynamic 69.59.196.210 00-15-5d-0a-3e-0e dynamic 69.59.196.212 00-21-5e-4d-45-c9 dynamic 69.59.196.213 00-15-5d-00-b2-0d dynamic 69.59.196.215 00-21-5e-4d-61-1a dynamic 69.59.196.217 00-21-5e-4d-2c-e8 dynamic 69.59.196.219 00-21-5e-4d-38-e5 dynamic 69.59.196.221 00-15-5d-00-b2-0d dynamic 69.59.196.222 00-15-5d-0a-3e-09 dynamic 69.59.196.223 ff-ff-ff-ff-ff-ff static 224.0.0.22 01-00-5e-00-00-16 static 224.0.0.252 01-00-5e-00-00-fc static 225.0.0.1 01-00-5e-00-00-01 static On our linux gateway instances arp -a shows: peak-colo-196-220.peak.org (69.59.196.220) at <incomplete> on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-222.peak.org (69.59.196.222) at 00:15:5d:0a:3e:09 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 Why would arp occasionally set the entry for this failed server as <incomplete>? Should we be defining our arp entries statically? I've always left arp alone since it works 99% of the time, but in this one instance it appears to be failing. Are there any additional troubleshooting steps we can take help resolve this issue? THINGS WE HAVE TRIED I added a static arp entry for testing on one of the linux gateways which still didn't help. root@haproxy2:~# arp -a peak-colo-196-215.peak.org (69.59.196.215) at 00:21:5e:4d:61:1a [ether] on eth1 peak-colo-196-221.peak.org (69.59.196.221) at 00:15:5d:00:b2:0d [ether] on eth1 stackoverflow.com (69.59.196.212) at 00:21:5e:4d:45:c9 [ether] on eth1 peak-colo-196-219.peak.org (69.59.196.219) at 00:21:5e:4d:38:e5 [ether] on eth1 peak-colo-196-209.peak.org (69.59.196.209) at 00:26:88:63:c7:80 [ether] on eth1 peak-colo-196-217.peak.org (69.59.196.217) at 00:21:5e:4d:2c:e8 [ether] on eth1 peak-colo-196-220.peak.org (69.59.196.220) at 00:21:5e:4d:30:8d [ether] PERM on eth1 root@haproxy2:~# arp -i eth1 -s 69.59.196.220 00:21:5e:4d:30:8d root@haproxy2:~# ping 69.59.196.220 PING 69.59.196.220 (69.59.196.220) 56(84) bytes of data. --- 69.59.196.220 ping statistics --- 7 packets transmitted, 0 received, 100% packet loss, time 6006ms Rebooting the windows web server solves this issue temporarily with no other changes to the network but our experience shows this issue will come back. Swapping network cards and switches I noticed the link light on the port of the switch for the failed windows server was running at 100Mb instead of 1Gb on the failed interface. I moved the cable to several other open ports and the link indicated 100Mb for each port that I tried. I also swapped the cable with the same result. I tried changing the properties of the network card in windows and the server locked up and required a hard reset after clicking apply. This windows server has two physical network interfaces so I have swapped the cables and network settings on the two interfaces to see if the problem follows the interface. If the public interface goes down again we will know that it is not an issue with the network card. (We also tried another switch we have on hand, no change) Changing network hardware driver versions We've had the same problem with the latest Broadcom driver, as well as the built-in driver that ships in Windows Server 2008 R2. Replacing network cables As a last ditch effort we remembered another change that occurred was the replacement of all of the patch cords between our servers / switch. We had purchased two sets, one green of lengths 1ft - 3ft for the private interfaces and another set of red cables for the public interfaces. We swapped out all of the public interface patch cables with a different brand and ran our servers without issue for a full week ... aaaaaand then the problem recurred. Disable checksum offload, remove TProxy We also tried disabling TCP/IP checksum offload in the driver, no change. We're now pulling out TProxy and moving to a more traditional x-forwarded-for network arrangement without any fancy IP address rewriting. We'll see if that helps.

  Read the article

• Windows 7 Not Recognizing Any Hardware, Linux Recognizing Hardware

  - by Newb

  I have a new desktop computer with two SSDs: one running Linux Mint 15 (SSD1), the other running Windows 7 (SSD2). My mint runs perfectly - USB wireless adapter is recognized, SSD2 (connected by SATA) is recognized and accessible through the filesystem, Ethernet works, etc. However, my Windows 7 is not recognizing any of these devices - even plugging in a regular ethernet cable doesn't work. It seems that it's not recognizing any network adapters, and it also doesn't recognize SSD1, connected to the mainboard by SATA. I've installed, uninstalled, and reinstalled Windows multiple times, but the problem persists. I used the Windows 7 CD to install Windows on a machine previously, and that time around, I didn't have any problems, which leads me to suspect that this might be a hardware issue, specifically with the mainboard. My mainboard is an MSI-7641 model, the 760GM-P34 FX. It uses an AMD Chipset and an AMD processor. Can anyone suggest what might be wrong, and how to fix it?

  Read the article

• Ubuntu dual monitor set up - taskbars appear on other monitor

  - by DisgruntledGoat

  I'm trying to get my TV (connected via HDMI cable) to act as a second monitor to watch video etc. The TV is to my left, so in Display Preferences I unticked "Mirror Screens" and put the monitors like this: -------- ---------- | PC | | TV | | | ---------- -------- When I do this, the PC monitor comes up with just the desktop wallpaper and the interface - taskbar and windows, etc - moves to the TV screen. But if I swap the monitors around, the taskbars are still on the TV screen, with the windows (and desktop icons) on the PC screen. Is there a way to set the computer monitor as the main one and the TV as the second screen? PC: Dell Inspiron 531 Monitor: Samsung SyncMaster 720N TV: Philips 26PFL5522D LCD TV

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by bakytn

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed)

  Read the article

• Configure a wireless network that accepts any WPA2-PSK network key

  - by Michel

  I recently bought a UART WiFi module ( this one ) and configured it with right SSID but wrong password( and I don't know what it is ). The problem is that I can't reset this module to its manufacture settings and I can't connect to this module via serial port to configure it with some wire or cable. But I'm sure that my module is trying to connect my access point but with wrong network key ( because in logs of my access point I can see my module that trying to connect but it can't ) So, I wonder to know is there any way to create or configure a network (using some access point or something else) based on WPA2 Personal security that accepts any WPA2-PSK passwords ? Or is there any other solution for this problem ? If no, is there anyway to see what password this module using to connect to that network ? ( If yes, then I can change password of my network to that password and access to this module's admin panel ) I tried create an open network ( without any security key ) but my module just searches for WPA2 based networks ( I think ).

  Read the article

• Keep getting invalid IP via WiFi

  - by nmuntz

  There is something wrong with my WiFi. I keep getting an invalid IP via DHCP (169.254.x.x), this happens for ALL wifi connections (home, office, etc). If I try a Local Ethernet connection via cable it works fine. I have tried downloading the latest drivers for my wireless adapter, resetting the TCP Stack and still have this issue. One strange thing I notice is under Device Manager, Network Adapters I have 4 "Unknown Devices" and three "Remote NDIS based Internet Sharing Device". My guess is that this belongs to McAfee. Not sure if this is related or not, anyways to try to fix this I tried downloading the NetLUIDfix.exe utility from McAfee but it didn't work. Any ideas how to solve this annoying issue? Thanks!!

  Read the article

• How to charge an iPhone on a Windows PC without Installing iTunes

  - by Martin Hollingsworth

  I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

  Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >