Search Results

Search found 3926 results on 158 pages for 'same origin policy'.

Page 50/158 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Connection refused after installing vsftp on Ubuntu 8.04 with fail2ban

    - by Patrick
    I have been using an Ubuntu 8.04 server with fail2ban for a while now (12+ months) and using ftp over SSH without any problems. I have a new user that needs to put files onto the server from an IP modem. I have installed vsftp (sudo apt-get install vsftp) and everything installed correctly. I have created an ftp user on the server following this guide. Whenever I try to connect to the server with my ftp program (filezilla) I get an immediate response of: Connection attempt failed with "ECONNREFUSED - Connection refused by server". I have looked into fail2ban and cannot find any problems. The iptables setup is: Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-ssh tcp -- anywhere anywhere multiport dports ssh Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- anywhere anywhere VSFTP config file (commented lines removed) listen=YES anonymous_enable=NO local_enable=YES write_enable=YES dirmessage_enable=YES xferlog_enable=YES connect_from_port_20=YES chown_uploads=YES chown_username=[username] secure_chroot_dir=/var/run/vsftpd pam_service_name=vsftpd rsa_cert_file=/etc/ssl/certs/ssl-cert-snakeoil.pem rsa_private_key_file=/etc/ssl/private/ssl-cert-snakeoil.key Any ideas on what is preventing access to the server?

    Read the article

  • Tripwire help Required

    - by ramaperumal
    I have created the policy file in Tripwire and also I have created the rules as well mentioned below: /opt/jboss/server/gis/conf -> $(SEC_CONFIG) +aipm +c+g+a+i+s+t+u+l+M; /usr/local/gtech/eseries/ -> $(SEC_CONFIG) +a+c+g+i+s+t+u+l+M ; After running the integrity check the output should be a(Access timestamp),c (Inode timestamp (create/modify),g (File owner's group ID),i (Inode number),s (File size),t (time stamp),u (File owner's user ID),l(File is increasing in size (a "growing file"),M (MD5 hash value). I am getting the output as below: [root@xxsi1242 tripwire]# tripwire --check Parsing policy file: /etc/tripwire/tw.pol *** Processing Unix File System *** Performing integrity check... Wrote report file: /var/lib/tripwire/report/xxsi1242.gtk.gtech.com-20131106-053812.twr Open Source Tripwire(R) 2.4.1 Integrity Check Report Report generated by: root Report created on: Wed 06 Nov 2013 05:38:12 AM EST Database last updated on: Wed 06 Nov 2013 05:31:17 AM EST =============================================================================== Report Summary: =============================================================================== Host name: xxsi1242.gtk.gtech.com Host IP address: 156.24.65.171 Host ID: None Policy file used: /etc/tripwire/tw.pol Configuration file used: /etc/tripwire/tw.cfg Database file used: /var/lib/tripwire/xxsi1242.gtk.gtech.com.twd Command line used: tripwire --check =============================================================================== Rule Summary: =============================================================================== ------------------------------------------------------------------------------- Section: Unix File System ------------------------------------------------------------------------------- Rule Name Severity Level Added Removed Modified --------- -------------- ----- ------- -------- Invariant Directories 66 0 0 0 Temporary directories 33 0 0 0 * Tripwire Data Files 100 0 0 1 Tech Stack 100 0 0 0 User binaries 66 0 0 0 Tripwire Binaries 100 0 0 0 * CLPS bins 100 0 0 2 CLPS Configuration files 100 0 0 0 ESCommon 100 0 0 0 Shell Binaries 100 0 0 0 OS executables and libraries 100 0 0 0 Security Control 100 0 0 0 ESCommon Configuration 100 0 0 0 (/etc/gtech/escommon) Total objects scanned: 12358 Total violations found: 3 =============================================================================== Object Summary: =============================================================================== ------------------------------------------------------------------------------- # Section: Unix File System ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Rule Name: Tripwire Data Files (/etc/tripwire/tw.pol) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/etc/tripwire/tw.pol" ------------------------------------------------------------------------------- Rule Name: CLPS bins (/opt/jboss/server) Severity Level: 100 ------------------------------------------------------------------------------- Modified: "/opt/jboss/server/esapps1/data/hypersonic/localDB.lck" "/opt/jboss/server/gis/data/hypersonic/localDB.lck" =============================================================================== Error Report: =============================================================================== No Errors ------------------------------------------------------------------------------- *** End of report *** Note: In the output I only am getting the files which are modified. I need the detail output for this. But unfortunately I am not getting what I expected. Please help me to proced further.

    Read the article

  • can't connect to vsftpd from outside network

    - by rick
    i know this has been asked many times before, but nothing seems to resolve my issue. i have vsftpd running on ubuntu 10.04. i can connect with ftp localhost on the machine. i can connect from another machine in my network. i just cannot connect from outside. the machine is behind an airport extreme managed by airport utility on a mac. 21 is open as per nmap: macmini:~$ nmap localhost Starting Nmap 5.21 ( http://nmap.org ) at 2011-04-10 23:49 EDT Nmap scan report for localhost (127.0.0.1) Host is up (0.00045s latency). Hostname localhost resolves to 2 IPs. Only scanned 127.0.0.1 rDNS record for 127.0.0.1: localhost.localdomain Not shown: 997 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 631/tcp open ipp netstat says 21 is listening: macmini:~$ netstat -lep --tcp | grep ftp (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 *:ftp *:* LISTEN iptables: macmini:~$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination when i try to connect from my external IP (or a dyndns name which resolves there) it times out. ("control connection timed out") as i know very little about networking, i feel like something may jump out as clearly wrong?

    Read the article

  • Debian/Ubuntu - No network connection

    - by leviathanus
    I have a very weird situation on my Ubuntu 12.04 LTS Server. I can not access (ping) my gateway, although I believe my config is ok - I attach the outputs. Any hints where to look? (I changed the beginning of the IP to something different, just obfuscation) ping 5.9.10.129 PING 5.9.10.129 (5.9.10.129) 56(84) bytes of data. From 5.9.10.129 (5.9.10.129) icmp_seq=2 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=3 Destination Host Unreachable From 5.9.10.129 (5.9.10.129) icmp_seq=4 Destination Host Unreachable uname -r 3.2.0-29-generic ifconfig eth0 eth0 Link encap:Ethernet HWaddr 3c:97:0e:0e:54:d7 inet addr:5.9.10.142 Bcast:5.9.10.159 Mask:255.255.255.224 inet6 addr: fe80::8e70:5aff:feda:c4ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1216 errors:0 dropped:0 overruns:0 frame:0 TX packets:490 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107470 (107.4 KB) TX bytes:34344 (34.3 KB) Interrupt:17 Memory:d2500000-d2520000 ip route default via 5.9.10.129 dev eth0 metric 100 5.9.10.128/27 via 5.9.10.129 dev eth0 5.9.10.128/27 dev eth0 proto kernel scope link src 5.9.10.142 route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 5.9.10.129 0.0.0.0 UG 1000 0 0 eth0 5.9.10.128 5.9.10.129 255.255.255.224 UG 0 0 0 eth0 5.9.10.128 0.0.0.0 255.255.255.224 U 0 0 0 eth0 iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination UPD: Eric, this is how routing information looks on a working server: 0.0.0.0 78.47.198.49 0.0.0.0 UG 100 0 0 eth0 78.47.198.48 78.47.198.49 255.255.255.240 UG 0 0 0 eth0 78.47.198.48 0.0.0.0 255.255.255.240 U 0 0 0 eth0 As I understand it, Hetzner tries to ensure security by this, so I can not take over an IP by changing my MAC. But this is another server, which has another netmask (255.255.255.240) UPD2: BatchyX, on the working server: 78.47.198.49 dev eth0 src 78.47.198.60 cache on the broken: 5.9.10.129 dev eth0 src 5.9.10.142 cache

    Read the article

  • Which events specifically cause Windows 2008 to mark a SAN volume offline?

    - by Jeremy
    I am searching for specific criteria/events that will cause Windows 2008 to mark a SAN volume as offline in disk management, even though it is connected to that SAN volume via FC or iSCSI. Microsoft states that "A dynamic disk may become Offline if it is corrupted or intermittently unavailable. A dynamic disk may also become Offline if you attempt to import a foreign (dynamic) disk and the import fails. An error icon appears on the Offline disk. Only dynamic disks display the Missing or Offline status." I am specifically wondering if, on the SAN, changing the path to the disk (such as the disk being presented to the host via a different iSCSI target IQN or a different LUN #) would cause a volume to be offlined in disk management. Thanks! Edit: I have already found two reasons why a disk might be set offline, disk signature collisions and the SAN disk policy. Bounty would be awarded to someone who can find further documented reasons related to changes in the volume's path. Disk signature collisions: http://blogs.technet.com/b/markrussinovich/archive/2011/11/08/3463572.aspx SAN disk policy: http://jeffwouters.nl/index.php/2011/06/disk-offline-with-error-the-disk-is-offline-because-of-a-policy-set-by-an-administrator/

    Read the article

  • Host name change breaking http? Fedora

    - by Dave
    OK so I have been messing around on my development server. It has been a while since I have had my head in linux and I suspect I have broken something. I have SSH running and that is working fine. I also have HTTP and I had FTP running also. Earlier today I decided I wanted to rename the machine so I updated the /etc/hosts file and /etc/sysconfig/network. I also changed the server name in the httpd.conf. I rebooted the machine and reconnected to SSH fine. Later I was messing around with the FTP service (trying to tighten up the user security) and when i tried to connect remotely to FTP no joy, it said cannot connect. I thought that was weird but had planned to remove ftp as we will be using github so removed ftp and moved on. Then I tried to connect to the website but major fail. even connecting to the IP address is failing. I used lynx to connect to the localhost and there was my site so something going on at server level. I thought maybe something up with iptables but I have not changed them but tried adding http but still no joy. I have a - Fedora release 17 (Beefy Miracle) NAME=Fedora VERSION="17 (Beefy Miracle)" ID=fedora VERSION_ID=17 PRETTY_NAME="Fedora 17 (Beefy Miracle)" ANSI_COLOR="0;34" CPE_NAME="cpe:/o:fedoraproject:fedora:17" Fedora release 17 (Beefy Miracle) Fedora release 17 (Beefy Miracle) Linux version 3.3.4-5.fc17.x86_64 ([email protected]) (gcc version 4.7.0 20120504 (Red Hat 4.7.0-4) (GCC) ) #1 SMP Mon May 7 17:29:34 UTC 2012 This is my iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere state RELATED,ESTABLISHED ACCEPT icmp -- anywhere anywhere ACCEPT all -- anywhere anywhere ACCEPT tcp -- anywhere anywhere state NEW tcp dpt:ssh REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) target prot opt source destination REJECT all -- anywhere anywhere reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) target prot opt source destination Like I say I can use SSH no issue but http although running is a no go from a remote computer. Any ideas?

    Read the article

  • Should I expect ICMP transit traffic to show up when using debug ip packet with a mask on a Cisco IOS router?

    - by David Bullock
    So I am trying to trace an ICMP conversation between 192.168.100.230/32 an EZVPN interface (Virtual-Access 3) and 192.168.100.20 on BVI4. # sh ip access-lists 199 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 # sh debug Generic IP: IP packet debugging is on for access list 199 # sh ip route | incl 192.168.100 192.168.100.0/24 is variably subnetted, 2 subnets, 2 masks C 192.168.100.0/24 is directly connected, BVI4 S 192.168.100.230/32 [1/0] via x.x.x.x, Virtual-Access3 # sh log | inc Buff Buffer logging: level debugging, 2145 messages logged, xml disabled, Log Buffer (16384 bytes): OK, so from my EZVPN client with IP address 192.168.100.230, I ping 192.168.100.20. I know the packet reaches the router across the VPN tunnel, because: policy exists on zp vpn-to-in Zone-pair: vpn-to-in Service-policy inspect : acl-based-policy Class-map: desired-traffic (match-all) Match: access-group name my-acl Inspect Number of Half-open Sessions = 1 Half-open Sessions Session 84DB9D60 (192.168.100.230:8)=>(192.168.100.20:0) icmp SIS_OPENING Created 00:00:05, Last heard 00:00:00 ECHO request Bytes sent (initiator:responder) [64:0] Class-map: class-default (match-any) Match: any Drop 176 packets, 12961 bytes But I get no debug log, and the debugging ACL hasn't matched: # sh log | inc IP: # # sh ip access-lists 198 Extended IP access list 198 10 permit icmp 192.168.100.0 0.0.0.255 host 192.168.100.20 20 permit icmp host 192.168.100.20 192.168.100.0 0.0.0.255 Am I going crazy, or should I not expect to see this debug log? Thanks!

    Read the article

  • Can't connect to vsftpd on Ubuntu 10.04

    - by Johnny
    I started the vsftpd on Ubuntu 10.04, but can't connect to it. The error says(FTP Client): Status: Connecting to 124.205.xx.xx:21... Error: Connection timed out Error: Could not connect to server I've checked the server status, and vsftpd is running: $ ps ax | grep vsftpd 23646 ? Ss 0:00 /usr/sbin/vsftpd 23650 pts/1 S+ 0:00 grep --color=auto vsftpd port 21 is under listening as well: $ netstat -tlnp | grep 21 (No info could be read for "-p": geteuid()=1000 but you should be root.) tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN - I can connect to localhost: $ ftp localhost Connected to localhost. 220 (vsFTPd 2.2.2) Name (localhost:jlee): 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> Here is iptables output $ sudo iptables -vL Chain INPUT (policy ACCEPT 191 packets, 144K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 124 packets, 28502 bytes) pkts bytes target prot opt in out source destination What's the problem here?

    Read the article

  • Internal Code Signing: Key Distribution, or Certificate Server?

    - by Myrddin Emrys
    I should first note that we have nobody in IT with significant familiarity with self-signed certification. We have a moderately sprawling network (one forest, many locations), and we are now rolling out internal code signing; until now users have run untrusted code, or we even disabled(!) the warnings. Intranet applications, scripts, and sites will now be signed with self certification. I am aware of two obvious ways we can deploy this: Distributing the keys directly via a group policy, and setting up a cert server. Can someone explain the trade-offs between these two methods? How many certs before the group policy method is unwieldy? Are they large enough that remote users will have issues? Does the group policy method distribute duplicates on every login? Is there a better method I am not aware of? I can find a lot of documentation on certifications and various ways to create them, but I have not been able to find something that summarizes the difference between the distribution methods and what criteria make one or the other superior.

    Read the article

  • iptables -- OK, **now** am I doing it right?

    - by Agvorth
    This is a follow up to a previous question where I asked whether my iptables config is correct. CentOS 5.3 system. Intended result: block everything except ping, ssh, Apache, and SSL. Based on xenoterracide's advice and the other responses to the question (thanks guys), I created this script: # Establish a clean slate iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT iptables -F # Flush all rules iptables -X # Delete all chains # Disable routing. Drop packets if they reach the end of the chain. iptables -P FORWARD DROP # Drop all packets with a bad state iptables -A INPUT -m state --state INVALID -j DROP # Accept any packets that have something to do with ones we've sent on outbound iptables -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT # Accept any packets coming or going on localhost (this can be very important) iptables -A INPUT -i lo -j ACCEPT # Accept ICMP iptables -A INPUT -p icmp -j ACCEPT # Allow ssh iptables -A INPUT -p tcp --dport 22 -j ACCEPT # Allow httpd iptables -A INPUT -p tcp --dport 80 -j ACCEPT # Allow SSL iptables -A INPUT -p tcp --dport 443 -j ACCEPT # Block all other traffic iptables -A INPUT -j DROP Now when I list the rules I get... # iptables -L -v Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any anywhere anywhere state INVALID 9 612 ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- lo any anywhere anywhere 0 0 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:ssh 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:http 0 0 ACCEPT tcp -- any any anywhere anywhere tcp dpt:https 0 0 DROP all -- any any anywhere anywhere Chain FORWARD (policy DROP 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 5 packets, 644 bytes) pkts bytes target prot opt in out source destination I ran it and I can still log in, so that's good. Anyone notice anything major out of wack?

    Read the article

  • Apache can't get viewed from outside of my LAN

    - by Javier Martinez
    I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

    Read the article

  • SNMP closed state in CentOS

    - by anksoWX
    I'm having a problem here, I've added to my IPtables rules this: -A INPUT -p tcp -m state --state NEW -m tcp --dport 161 -j ACCEPT -A INPUT -p udp -m state --state NEW -m udp --dport 161 -j ACCEPT but when I scan with nmap or any other tool it says this: Not shown: 998 filtered ports PORT STATE SERVICE 22/tcp open ssh 161/tcp closed snmp also when I am doing: netstat -apn | grep snmpd tcp 0 0 127.0.0.1:199 0.0.0.0:* LISTEN 3669/snmpd<br> udp 0 0 0.0.0.0:161 0.0.0.0:* 3669/snmpd<br> unix 2 [ ] DGRAM 226186 3669/snmpd Also: service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination 1 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 2 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 3 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 4 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:161 5 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:161 6 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 7 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain OUTPUT (policy ACCEPT) num target prot opt source destination Any idea what's going on? There is no UDP in closed/open state. what do I have to do?

    Read the article

  • Iptables ignoring a rule in the config file

    - by Overdeath
    I see lot of established connections to my apache server from the ip 188.241.114.22 which eventually causes apache to hang . After I restart the service everything works fine. I tried adding a rule in iptables -A INPUT -s 188.241.114.22 -j DROP but despite that I keep seeing connections from that IP. I'm using centOS and i'm adding the rule like thie: iptables -A INPUT -s 188.241.114.22 -j DROP Right afther that I save it using: service iptables save Here is the output of iptables -L -v ` Chain INPUT (policy ACCEPT 120K packets, 16M bytes) pkts bytes target prot opt in out source destination 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any c-98-210-5-174.hsd1.ca.comcast.net anywhere 0 0 DROP all -- any any c-98-201-5-174.hsd1.tx.comcast.net anywhere 0 0 DROP all -- any any lg01.mia02.pccwbtn.net anywhere 0 0 DROP all -- any any www.dabacus2.com anywhere 0 0 DROP all -- any any 116.255.163.100 anywhere 0 0 DROP all -- any any 94.23.119.11 anywhere 0 0 DROP all -- any any 164.bajanet.mx anywhere 0 0 DROP all -- any any 173-203-71-136.static.cloud-ips.com anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any 74.122.177.12 anywhere 0 0 DROP all -- any any 58.83.227.150 anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere 0 0 DROP all -- any any v1.oxygen.ro anywhere Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 186K packets, 224M bytes) pkts bytes target prot opt in out source destination `

    Read the article

  • Bandwidth monitoring with iptables for non-router machine

    - by user1591276
    I came across this tutorial here that describes how to monitor bandwidth using iptables. I wanted to adapt it for a non-router machine, so I want to know how much data is going in/coming out and not passing through. Here are the rules I added: iptables -N ETH0_IN iptables -N ETH0_OUT iptables -I INPUT -i eth0 -j ETH0_IN iptables -I OUTPUT -o eth0 -j ETH0_OUT And here is a sample of the output: user@host:/tmp$ sudo iptables -x -vL -n Chain INPUT (policy ACCEPT 1549 packets, 225723 bytes) pkts bytes target prot opt in out source destination 199 54168 ETH0_IN all -- eth0 * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1417 packets, 178128 bytes) pkts bytes target prot opt in out source destination 201 19597 ETH0_OUT all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain ETH0_IN (1 references) pkts bytes target prot opt in out source destination Chain ETH0_OUT (1 references) pkts bytes target prot opt in out source destination As seen above, there are no packet and byte values for ETH0_IN and ETH0_OUT, which is not the same result in the tutorial I referenced. Is there a mistake that I made somewhere? Thanks for your time.

    Read the article

  • Nginx Ubuntu Postfix Config - Can't connect to incoming IMAP server 'server not responding' but can send mail via outgoing using same details?

    - by daveaspinall
    I'm pretty to new server admin and especially nginx but seem to be getting ok fine apart from accessing my mail via my iPhone? I've changed my domain to 'domain.com' The thing is I can send mail via my outgoing IMAP server but can't connect to the incoming one? I just get the message "the mail server at mail.domain.com is not responding" /etc/postfix/main.cf alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix home_mailbox = Maildir/ inet_interfaces = all inet_protocols = all mailbox_command = mailbox_size_limit = 0 mydestination = domain.com, mail.domain.com, localhost.com, , localhost, localhost.localdomain mydomain = domain.com myhostname = mail.domain.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname recipient_delimiter = + relayhost = smtp_tls_note_starttls_offer = yes smtp_tls_security_level = may smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = permit_sasl_authenticated,permit_mynetworks,reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_tls_CAfile = /etc/ssl/certs/cacert.pem smtpd_tls_auth_only = no smtpd_tls_cert_file = /etc/ssl/certs/smtpd.crt smtpd_tls_key_file = /etc/ssl/private/smtpd.key smtpd_tls_loglevel = 1 smtpd_tls_received_header = yes smtpd_tls_security_level = may smtpd_tls_session_cache_timeout = 3600s tls_random_source = dev:/dev/urandom telnet localhost 25 ehlo locahost 250-mail.domain.com 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-AUTH LOGIN PLAIN 250-AUTH=LOGIN PLAIN 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN Using the following details to connect: username password hostname: mail.domain.com port: 25 iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination I also sent mail to the server as a test and got this missage if it helps? Technical details of temporary failure: [mail.domain.com. (10): Connection refused] I also looked in /var/log/mail.log and it has multiple entries of: postfix/smtpd[12239]: connect from 5acefc9a.bb.sky.com[90.206.252.xxx] Mar 23 06:47:09 new-domain postfix/smtpd[12239]: lost connection after CONNECT from 5acefc9a.bb.sky.com[90.206.252.154] Notice new-domain which is incorrect but the server hostname and hostname in the configs are correct? I recently moves servers and the host has set the primary domain on the service as new-domain.com so this may be the issue? Like I said, it works to connect to outgoing server, but incoming gets the not responding error? Any idea would be much appreciated!

    Read the article

  • Exchange 2003: Accounts with only OWA access unable to change passwords when expired or forced

    - by radioactive21
    We have accounts whith only OWA access, because they are generic accounts and we do not want the accounts to be used as machine logins. We have a password policy that users must change their passwords every 6 months. The problem we are having is that since the accounts are not loging into the machines, when the password policy kicks in it is preventing users with OWA only access from changing their password. Also, when we select "User must change the password at next logon" it also causes the same issue. We have two exchange servers the main one and a front end one. what we have been doing with these generic account is in properties, under the "account" tab we restricted "log on to" to the front end server. Just to clarify, when we have no restrictions, users can change their passwords via the web without any issues. It is only when we force them to only login via OWA that they cant change passwords. I tried adding our domain controler and main exchange server to the "This user can log on to The following computers" in the account tab, but still it is not allowing them to change passwords. Currently I have to manually reset the passwords for OWA only accounts. Is there anyway to allow OWA acconts to change passwords? EDIT: Users restricted to only OWA can change their password via the web browser without any issues when there are no restrictions. In other words normally they can just log into outlook via the web and change their password, but when the password policy expires or we force them to change their password at next login, they are unable to.

    Read the article

  • fail2ban iptable rule wont block

    - by Termiux
    So I set up fail2ban on my Debian 7 server, still I've been getting hit a lot and I dont know why is not blocking properly. The regex works, it recognizes the attempts but it seems the iptables rules it insert wont work, this is how it look iptables ouput looks after fail2ban tries to block. Chain INPUT (policy ACCEPT) num target prot opt source destination 1 fail2ban-courierauth tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 2 fail2ban-couriersmtp tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:25 3 sshguard all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination Chain fail2ban-courierauth (1 references) num target prot opt source destination 1 DROP all -- 216.x.y.z 0.0.0.0/0 2 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-courierimap (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-courierpop3 (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-couriersmtp (1 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-postfix (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-sasl (0 references) num target prot opt source destination 1 RETURN all -- 0.0.0.0/0 0.0.0.0/0 In the iptables above you can see the "Chain fail2ban-courierauth" rule that added the drop rule for the ip but Im still able to connect!! I can still connect to the server, why isn't it blocking?

    Read the article

  • iptables blank after reboot

    - by theillien
    We've started encountering an issue with iptables on our RHEL 6.3 systems in that after a reboot, when the service starts, the rules are not loaded. We get the empty ruleset: [msnyder@matt-test ~]$ sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination This is in spite of the fact that we have rules defined and the service is, indeed, running. That I know because when I run service iptables start it simply drops back to the prompt. If I run service iptables restart it actually stops and then restarts the service. And, of course, if I run service iptables stop it indicates that iptables is actually stopping. Knowing that I need to restart the service, I do so and the rules load up properly. They simply don't get loaded after a reboot. Unless they get loaded differently during a reboot I don't see how our rules would be wrong. If they were, they wouldn't even load during a service restart. Has anyone else ever encountered this? EDIT: The rules are already saved in /etc/sysconfig/iptables. They are not added on the fly from the command line so service iptables save is unnecessary.

    Read the article

  • Redirect traffic from 127.0.0.1 to 127.0.0.1 on port 53 to port 5300 with iptables

    - by Zagorax
    I'm running a local dns server on port 5300 to develop a software. I need my machine to use that dns but I wasn't able to tell /etc/resolv.conf to check on a different port. I searched a bit on google and I didn't find a solution. I set 127.0.0.1 as nameserver on /etc/resolv.conf. This is my whole /etc/resolv.conf: nameserver 127.0.0.1 Could you please tell me how can I redirect outbound traffic on port 53 to another port? I tried the following but it didn't work: iptables -t nat -A PREROUTING -p tcp --dport 53 -j DNAT --to 127.0.0.1:5300 iptables -t nat -A PREROUTING -p udp --dport 53 -j DNAT --to 127.0.0.1:5300 Here is the output of iptables -t nat -L -v -n (with suggested rules): Chain PREROUTING (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination 0 0 REDIRECT tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp dpt:53 redir ports 5300 0 0 REDIRECT udp -- * * 0.0.0.0/0 0.0.0.0/0 udp dpt:53 redir ports 5300 Chain POSTROUTING (policy ACCEPT 302 packets, 19213 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 302 packets, 19213 bytes) pkts bytes target prot opt in out source destination

    Read the article

  • Github file size limit changed 6/18/13. Can't push now

    - by slindsey3000
    How does this change as of June 18, 2013 affect my existing repository with a file that exceeds that limit? I last pushed 2 months ago with a large file. I have a large file that I have removed locally but I can not push anything now. I get a "remote error" ... remote: error: File cron_log.log is 126.91 MB; this exceeds GitHub's file size limit of 100 MB I added the file to .gitignore after original push... But it still exists on remote (origin) Removing it locally should get rid of it at origin(Github) right? ... but ... it is not letting me push because there is a file on Github that exceeds the limit... https://github.com/blog/1533-new-file-size-limits These are the commands I issued plus error messages.. git add . git commit -m "delete cron_log.log" git push origin master remote: Error code: 40bef1f6653fd2410fb2ab40242bc879 remote: warning: Error GH413: Large files detected. remote: warning: See http://git.io/iEPt8g for more information. remote: error: File cron_log.log is 141.41 MB; this exceeds GitHub's file size limit of 100 MB remote: error: File cron_log.log is 126.91 MB; this exceeds GitHub's file size limit of 100 MB To https://github.com/slinds(omited_here)/linexxxx(omited_here).git ! [remote rejected] master - master (pre-receive hook declined) error: failed to push some refs to 'https://github.com/slinds(omited_here) I then tried things like git rm cron_log.log git rm --cached cron_log.log Same error.

    Read the article

  • Scrolling screen upward to expose TextView above keyboard

    - by Matt Winters
    I think I'm missing something obvious and would appreciate an answer. I have a view with a 2-section grouped tableView, each section having one row and a textView, the heights of the rows 335 and 140. This allows for a box with nicely rounded corners to type text into when the keyboard appears (140 height section) and when the keyboard is dismissed, a nice box to read more text (notes); most of the time, use is without the keyboard. I also added a toolbar at the bottom of the screen to scroll up above the keyboard. A button on the toolbar dismisses the keyboard. This last part works fine with the keyboard going up and down using a notification and the following code in a keyboardWillShow method: [UIView beginAnimations:@"showKeyboardAnimation" context:nil]; [UIView setAnimationDuration:0.50]; self.view.frame = CGRectMake(self.view.frame.origin.x, self.view.frame.origin.y, self.view.frame.size.width, self.view.frame.size.height - 216); [UIView commitAnimations]; But with the above code, the 2 sections of the tableView remain unscrolled, only the toolbar and the keyboard move. With the following code (found both in previous posts), both the toolbar and the tableView sections move. [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:0.50]; CGRect rect = self.view.frame; rect.origin.y -= 216; self.view.frame = rect; [UIView commitAnimations]; Now I know that I have to tweak the numbers to get the everything as I want it but my first question is what is substantively different between the 2 sets of code that the sections move in the 2nd but not in the 1st? The toolbar also moves with the 2nd code. The second question is, am I going to be able to scroll the smaller height section from off the screen to above the keyboard while at the same time moving the toolbar up just 216? Thanks

    Read the article

  • javascript function not working in IE 7

    - by JPro
    Hi, Can anyone please tell me how do I make this script run in IE 7? When I run this , nothing happens. <html> <body> <script language="JavaScript"> function moveSelectedOption() { // Fetch references to the <select> elements. var origin = document.getElementById('origin_select'); var target = document.getElementById('target_select'); // Fetch the selected option and clone it. var option = origin.options[origin.selectedIndex]; var copy = option.cloneNode(true); // Add the clone to the target element. target.add(copy, null); } </script> <select id="origin_select" multiple> <option value="A">A</option> <option value="B">B</option> <option value="C">C</option> </select> <select id="target_select" multiple> <option value="C1">C1</option> </select> <button onclick="moveSelectedOption()">Add</button> </body> </html>

    Read the article

  • Adding a UIPickerView over a UITabBarController

    - by Kai
    I'm trying to have a UIPickerView slide from the bottom of the screen (over the top of a tab bar) but can't seem to get it to show up. The actual code for the animation is coming from one of Apple's example code projects (DateCell). I'm calling this code from the first view controller (FirstViewController.m) under the tab bar controller. - (IBAction)showModePicker:(id)sender { if (self.modePicker.superview == nil) { [self.view.window addSubview:self.modePicker]; // size up the picker view to our screen and compute the start/end frame origin for our slide up animation // // compute the start frame CGRect screenRect = [[UIScreen mainScreen] applicationFrame]; CGSize pickerSize = [self.modePicker sizeThatFits:CGSizeZero]; CGRect startRect = CGRectMake(0.0, screenRect.origin.y + screenRect.size.height, pickerSize.width, pickerSize.height); self.modePicker.frame = startRect; // compute the end frame CGRect pickerRect = CGRectMake(0.0, screenRect.origin.y + screenRect.size.height - pickerSize.height, pickerSize.width, pickerSize.height); // start the slide up animation [UIView beginAnimations:nil context:NULL]; [UIView setAnimationDuration:0.3]; // we need to perform some post operations after the animation is complete [UIView setAnimationDelegate:self]; self.modePicker.frame = pickerRect; // shrink the vertical size to make room for the picker CGRect newFrame = self.view.frame; newFrame.size.height -= self.modePicker.frame.size.height; self.view.frame = newFrame; [UIView commitAnimations]; // add the "Done" button to the nav bar self.navigationItem.rightBarButtonItem = self.doneButton; }} Whenever this action fires via a UIBarButtonItem that lives in a UINavigationBar (which is all under the FirstViewController) nothing happens. Can anyone please offer some advice?

    Read the article

  • Git : Failed at pushing to remote server, ' REPOSITORY_PATH ' is not a git command

    - by Judarkness
    I'm using Git with TortoiseGit on Windows XP, and I have a remote bare repository on Windows Vista 64bit version. When I tried to push my local files to remote bare repository, I got the following error message. git.exe push "origin" master:master git: 'C:/Git_Repository/.git' is not a git command. See 'git --help'. fatal: The remote end hung up unexpectedly the arbitrary URL is : username@serverip:C:/Git_Repository/.git The same arbitrary URL worked just fine while doing clone/fetch/pull. Access from a local directory in remote machine to this bare repository has no problem either so I belive there is something wrong with my path. I can push/pull at GitHub correctly but I was using URL provide by GitHub. Does anyone know what's wrong with my configuration? Here is my remote .git/config [core] repositoryformatversion = 0 filemode = false bare = true logallrefupdates = true ignorecase = true hideDotFiles = dotGitOnly Here is my local .git/config [core] repositoryformatversion = 0 filemode = false bare = false logallrefupdates = true symlinks = false ignorecase = true hideDotFiles = dotGitOnly [remote "origin"] fetch = +refs/heads url = username@serverip:C:/Git_Repository/.git [branch "master"] remote = origin merge = refs/heads/master Thanks for the reminding

    Read the article

  • iPhone Dev:Blurring of CALayers when rotated

    - by user153231
    Hello All, I have a CALayer with a png image as its content.When rotation is applied the layer looks blurry. I've searched for a cause for this problem and found out that the problem might be the half pixel problem, which makes the layer blurry if its frame.origin lays on fractions like 96.5, and they suggest to make the origin a whole number. Now, my layer's origin contains fractions because of the rotation i make as in: tempLayer.anchorPoint = CGPointMake(0.5,0.5); tempLayer.position = CGPointMake(200,100); tempLayer.bounds = CGRectMake(0,0,70,88); tempLayer.transform = CATransform3DMakeRotation(10.f*M_PI/180.f, 0.f, 0.f, 1.f); tempLayer.contents = (id)myImage; Basically i have three questions: 1) Is there a better way to rotate the layer? 2) The frame values are derived from the anchorPoint, position, bounds and transform values, how can i round my frame values to integer values and keep my rotation intact? 3) Can the CGRectIntegral function help me? If yes how? Thank you all in advance.

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >