Search Results

Search found 13692 results on 548 pages for 'bad practices'.

Page 501/548 | < Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >

• iTunes and Hulu Playback Choppy and Slow?

  - by Bart Silverstrim

  Specs: Windows XP, latest updates 1.7 ghz Pentium 4 1 gig ram DirectX 9.0c NVIDIA GeForce FX 5200 with 256 meg RAM OpenGL 2.1 The story: Okay, I had an older system laying around that I figured I would try turning into a mini-media system to connect to our TV. I put together a lot of older parts, got it into working order, etc. and hooked it up and voila'...slower, but usable system that displayed to the TV. It could run some things decently. I put in iTunes, it played video okay. Not great, but okay. Played Hulu and since we have a 1Mb download rate, the minimum for their site, there were some choppy moments when watching their shows, but I found that (sadly) changing resolution to 800x600 seemed to help with the issue when running full screen. I downloaded the application called Boxee and installed it. It wouldn't run; apparently the video card in the system supported OpenGL 1.2, and needed at least 1.4. I bought a cheap card, the 5200, with four times the memory in it and support for OpenGL 2.1. Installed, everything seemed fine. iTunes seemed to run fine, the video driver (PNY video card) came with OpenGL 2.1, and Boxee finally ran. I then upgraded to the latest drivers for the video card and ran the DirectX updater from MS. After that, the OpenGL Extension Viewer wouldn't run. It just stayed as an icon in the task bar. Also, any and all videos in iTunes stuttered and went out of sync horribly. Unwatchable. I tried watching Hulu video in Boxee, and it displayed video like it was a series of stills in a very bad powerpoint. Playing straightforward audio-only came through fine, no stutters no hiccups. I tried system restore to roll back updates to pre-directX updates (I thought that seemed to be the time that triggered the weird behavior), no joy. I tried uninstalling and reinstalling the video drivers. I installed updated audio drivers (ensoniq audiopci), nothing helped. I finally wiped the drive last night and tried reinstalling everything and restoring my iTunes content via an import from a backup. Fresh install, no updater on the video card or directx. the problem was still there although I haven't tested Hulu, the iTunes player is still stuttering like crazy if I play video, fine if I play audio. I know the processor isn't high in heft, but with one gig of RAM and the fact that it seemed to do okay before I thought that the problem must be software related. Has anyone else run into this sort of issue and have a solution other than "buy a new computer"? What specs seem to work with video at the low end for you? Right now the system is of little use other than keeping my music library and iTunes apps synced with my iPod.

  Read the article

• Dlink search is hijacking my browser

  - by James

  For months now "DLink search" has been hijacking my search engines. I use google chrome, and I have organized my search engines in the handy dandy "manage search engines" tool about a TRILLION times. It never even says D-link is hacking my search engines. It does not show up! I have read many posts on this forum and others saying that to fix this problem from internet explorer: Setup, internet options, yadayada, magical fairies, and you are solved, but my browser is google chrome! How am I supposed to do this from there! I do not know how to re-setup my Dlink router, which is the cause of the problem! HOW? In those posts with the magical fairies fixing it, HUNDREDS responded saying, "yep, those fairies definitely fixed it right. :)" These people were so satisfied. IT WORKED FOR THEM, WHY NOT ME. I look at it and go ":(" because it does not help me. There are no options for anything to do with this in GOOGLE chrome. PLEASE EXPLAIN and HELP. I see no "SETUP" option, no "Internet Options" button, no anything. BTW the exact posts are these: "Uncheck Advanced DNS in the router internet setup. This will take care of it. I had this problem with my DLink router before." "I had this issue with my DIR-655 and unchecking the Advanced DNS setting in Setup - Internet - Manual Internet Connection Setup fixed it." "If this is just internet explorer, you can go to Tools Internet Options or Internet Options in Control Panel. From here, go to the advanced tab and click the Reset button." "I would set the router's DNS to a site like OpenDNS, and I would ensure the machines are set to get their DNS settings via DHCP or set the machine's DNS setting to OpenDNS. If the router's DNS looks like it was messed with, some bad software know the default passwords for routers and could have changed it. If you don't already I would make sure the password to the router is not default or easy to guess. I've had spyware change a machine's DNS, but the fact it is happening on all machines makes me wonder if it is the router." "Something got into your router and changed the dns server most likely, do a hard reset of the router and then change the password to something strong. Also check for a firmware update for the router and apply it as soon as possible."

  Read the article

• git private server error: "Permission denied (publickey)."

  - by goddfree

  I followed the instructions here in order to set up a private git server on my Amazon EC2 instance. However, I am having problems when trying to SSH into the git account. Specifically, I get the error "Permission denied (publickey)." Here are the permissions of my files/folders on the EC2 server: drwx------ 4 git git 4096 Aug 13 19:52 /home/git/ drwx------ 2 git git 4096 Aug 13 19:52 /home/git/.ssh -rw------- 1 git git 400 Aug 13 19:51 /home/git/.ssh/authorized_keys Here are the permissions of my files/folders on my own computer: drwx------ 5 CYT staff 170 Aug 13 14:51 .ssh -rw------- 1 CYT staff 1679 Aug 13 13:53 .ssh/id_rsa -rw-r--r-- 1 CYT staff 400 Aug 13 13:53 .ssh/id_rsa.pub -rw-r--r-- 1 CYT staff 1585 Aug 13 13:53 .ssh/known_hosts When checking my logs in /var/log/secure, I used to get the following error message every time I tried to SSH: Authentication refused: bad ownership or modes for file /home/git/.ssh/authorized_keys However, after making a few permission changes, I no longer get this error message. Despite this, I am still getting the "Permission denied (publickey)." message every time I try to SSH. The command I am using to SSH is ssh -T git@my-ip. Here is the full log I get when I run ssh -vT [email protected]: OpenSSH_6.2p2, OSSLShim 0.9.8r 8 Dec 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to my-ip [my-ip] port 22. debug1: Connection established. debug1: identity file /Users/CYT/.ssh/id_rsa type -1 debug1: identity file /Users/CYT/.ssh/id_rsa-cert type -1 debug1: identity file /Users/CYT/.ssh/id_dsa type -1 debug1: identity file /Users/CYT/.ssh/id_dsa-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.2 debug1: Remote protocol version 2.0, remote software version OpenSSH_6.2 debug1: match: OpenSSH_6.2 pat OpenSSH* debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr [email protected] none debug1: kex: client->server aes128-ctr [email protected] none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 08:ad:8a:bc:ab:4d:5f:73:24:b2:78:69:46:1a:a5:5a debug1: Host 'my-ip' is known and matches the RSA host key. debug1: Found key in /Users/CYT/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /Users/CYT/.ssh/id_rsa debug1: Trying private key: /Users/CYT/.ssh/id_dsa debug1: No more authentication methods to try. Permission denied (publickey). I have spent a few hours going through threads on various sites, including SO and SF, looking for a solution. It seems that the permissions for my files are all okay, but I just can't figure out the problem. Any help would be greatly appreciated. Edit: EEAA: Here are the outputs you requested: $ getent passwd git git:x:503:504::/home/git:/bin/bash $ grep ssh ~git/.ssh/authorized_keys | wc -l grep: /home/git/.ssh/authorized_keys: Permission denied 0

  Read the article

• Recovering from backup without original install media

  - by KGendron

  A machine from my old job had a complete hard drive failure. I have backups but I'm running into severe problems restoring from them. The only install media was a secondary restore partition on the system's hard drive. I hate whoever came up with that idea more than i can possibly express with words. I spent several days trying to recover the disk - it is pretty well shot and none of my best tricks could even get it to show up in the bios/ The machine that broke is an hp with xp media center edition on it (I don't know why either). The backups were created using the default windows backup tool - I have .bfk file on an external hardrive that i am trying to restore from. I've replaced the hard drive. My home machine is running windows 7 64bit and i'm trying to use it as a platform to restore to the other disk. I downloaded the window 7 nt-restore utility, however no matter what i do it restores to my C drive rather than the specified drive. Fortunately win7 security settings prevented it from being a complete disaster - but still not a happy thing. I tried firing up the xp virtual machine. I can browse to the backups but it says they are invalid and refuse to let me view/ continue with the restore. I tried installing XP to an extra harddrive on my machine - however it bluescreens on me during the install process and I cry. I tried installing xp pro to the new drive and attempted to restore over it, it of course blackscreened on me as that was a stupid idea. I made two partitions on the new hard drive (Apparently the bios on this accursed piece of junk doesn't allow hd partitions larger than 200G anyways and thus fails 40 minutes into the install with an ever-descriptive "Disk Read Error". Guess how i spent last weekend? My last idea was to install xp pro to the second partition and then use it to restore from backup to the first. After the first restart it gives me the error "Windows could not start because of a computer disk hardware configuration problem. Could not read from the selected boot disk. Check boot path and disk hardware". My brain made one of those bad hard drive clicky noises. I've tried several boot disks but they don't seem to work. If anyone has a link to a good one it would be greatly appreciated. Anyone have any more ideas? - I really hate asking on what seems like such a simple issue but i am quite literally at my wit's end. Thanks - and sorry for the really long post.

  Read the article

• Expendable, Redundant, Easily recoverable

  - by MeIr

  I am desperate at this point, I have been looking for "Big storage" solution for a while on my own and I can't find anything that would suite my needs. But now push came to shove. Current situation: I have about 6TB data storage (already full) - Drobo. Yesterday Drobo died on me and it put me into bad situation - I can't recover my data without buying another Drobo. From extensive research online I realized that Drobo is not the safest bet and by now it seems very poor choice. I ordered new Drobo to try to get my data back, however I don't want to be in the same situation later and continuing using Drobo promises this event to re-occur. What I am looking for: 1) Inexpensive setup. 2) Dynamically extendable - add more drives and/or replace a drive with bigger capacity. 3) Redundant - setup against 1-3 drive failure, will depend on total number of drives. For the sake of argument let's assume for every 4 drives one should be able to fail without data loss. 4) Easy data recovery - let's say unforeseen happens, I would like to be able to recover information without buying new tools or replacements - example: new Drobo. 5) Should be USB or Network Attach Storage 6) No demand on speed. Doesn't have to be fast, I am not doing video editing on the setup. However if option exists, would be nice to have a decent speed. After thoughts: I reviewed few options and FreeNAS looks nice, but it doesn't have #2 - Dynamic extendability. There are work around with Pools but it seems a bit complicated and unnecessary. More over it seems like data safety is a big question - saw some horror stories. Please advise on what options I have and what seems like an optimal solution (if any). I don't care if it has to be Windows or Linux box or any other OS and/or software that has to run on top, but simple solution is more attractive. Thank you! P.S: Feel free to ignore "After thoughts".

  Read the article

• What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

  - by Tyler

  Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

  Read the article

• SQLS Timeouts - High Reads in Profiler

  - by lb01

  I've audited a SQLS2008 server with Profiler for one day.. the overhead didn't seem to trouble this new client my company has. They are using a legacy VB6 application as a front-end. They're experiencing timeouts once SQLS RAM usage is high. The server is currently running x64 sqls2008 on a VM with nearly 9 GB of RAM. SQL Server's 'max server memory option' is currently set to 6GB. I've put the results of the trace in a table and queried them using this query. SELECT TextData, ApplicationName, Reads FROM [TraceWednesday] WHERE textdata is not null and EventClass = 12 GROUP BY TextData, ApplicationName, Reads ORDER BY Reads DESC As I expected, some values are very high. Top Reads, in pages. 2504188 1965910 1445636 1252433 1239108 1210153 1088580 1072725 Am I correct in thinking that the top one (2504188 pages) is 20033504 KB, which then is roughly ~20'000 MB, 20GB? These queries are often executed and can take quite some time to run. Eventually RAM is used up because of the cache fattening, and timeouts occur once SQL cannot 'splash' pages in the buffer pool as much. Costs go up. Am I correct in my understanding? I've read that I should tune the associated T-SQL and create appropriate indices. Obviously cutting down the I/O would make SQL Server use less RAM. OR, maybe it might just slow down the process of chewing up the whole RAM. If a lot less pages are read, maybe it'll all run much better even when usage is high? (less time swapping, etc.) Currently, our only option is to restart SQL once a week when RAM usage is high, suddenly the timeouts disappear. SQL breathes again. I'm sure lots of DBAs have been in this situation.. I'm asking before I start digging out all of the bad T-SQL and put indices here and there, is there is something else I can do? Any advice except from what I know (not much yet..) Much appreciated. Leo.

  Read the article

• My VPS ubuntu server is very slow

  - by askmike

  I just installed a frech copy of Ubuntu 12.04 on my vps because my old installation was very slow, unfortunately this did not fix the problem. With slow I mean requests for my PHP websites take a long time, very slow (30 sec per request) to slow (3+ sec per request). When it's really bad SSH is also laggish. The websites are: askmike.org (pretty standard Wordpress) mvr.me (own PHP) slow? very slow: Here is a picture of loading a clean install of wordpress slow: here is a picture of loading a small PHP based website the vps The VPS has 256mb ram and an 25GB hdd. Besides serving the 2 small websites it isn't doing anything AFAIK. What have I installed Clean Ubuntu server 12.04 LAMP stack few things like git and nodejs (not using both) ossec (because I thought my server was getting hammered) munin What I already tried / done I installed munin so that I could watch io speed and such. The problem is that I don't know where to look for in the munin report. I checked logs and don't see anything strange (although I don't really know where to look for besides strange / repetitive errors and GET requests). I configured Apache MPM to: <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 40 MaxRequestsPerChild 0 </IfModule> (apache is using prefork, the default) Stats I copied the munin report as it appeared at 4:50 last night to a site hosted on a shared webhost. Note that tonight my mysql crashed somewhere after 1:00 (which is a new problem altogether), so therefor the graph for last night might look strange. Can anyone help me get my VPS up to normal speed? EDIT: Thanks for the replies. The VPS is 10 bucks a month and is from directvps.nl (Dutch host and I'm also dutch). I did two speed tests for disk IO: $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 23.1506 s, 46.4 MB/s $ dd if=/dev/zero of=test bs=64k count=16k conv=fdatasync 1073741824 bytes (1.1 GB) copied, 39.3796 s, 27.3 MB/s Anyway: how can I prove to my VPS host that it is to slow? I can understand a server being busy slowing a website down. But 5-30 sec loadtime for a normal PHP webpage?

  Read the article

• How to configure apache's mod_proxy_html to work as an ajax proxy?

  - by dcerecedo

  I'm trying to build a web site that let's you view and manipulate data from any page in any other website. To do that, I have to bypass 'Allow Origin' problems: i'm loading the other domain's content in an iframe and i have to manipulate its content with javascript downloaded from my domain. My first attempt was to write a simple proxy myself, requesting the other domains page through a server proxy coded in Java that not only serves the content but rebuilds links (src's and href's) in the content so that the content referenced by these links alse get downloaded through my handmade proxy. The result is not bad but has problems with url's in css and scripts. It's then that i realized that mod_proxy_html is supposed to do exactly all this job. The problem is that i cannot figure out how to make it work as expected. Let's suppose my server runs in my-domain.com and to proxy and transform content from another domain i'd make a request like this: my-domain.com/proxy?url=http://another-domain.com/some/content I'd want mod_proxy_html to serve the content and rewrite following URLs in http://another-domain.com/some/content in the following ways: Absolute URLs not from another-domain.com: no rewritting Relative from root urls:/other/content - /proxy?url=http://another-domain.com/other/content Relative urls: other/content - /proxy?url=http://another-domain.com/some/content/other/content Relative to parent urls: ../other/content - /proxy?url=http://another-domain.com/some/other/content The url should be specified at runtime, not configuration time. Can this be achieved with mod_proxy_html? Could anyone provide a simple working configuration to start with? EDIT 1-First approach The following site config will work fine with sites that use absolute url's everywhere like http://www.huffingtonpost.es/. Youc could try on this config on localhost: http://localhost/asset/http://www.huffingtonpost.es/ <VirtualHost *:80> ServerName localhost LogLevel debug ProxyRequests off RewriteEngine On RewriteRule ^/asset/(.*) $1 [P] ProxyHTMLURLMap $1 /asset/ <Location /asset/> ProxyPassReverse / ProxyHTMLURLMap / /asset/ </Location> </VirtualHost> But as explained in the documentation, if I hit a site using relative url's, I'd like to have these rewritten on the html via mod_proxy_html. So I shoud change the Location block as follows: <Location /asset/> ProxyPassReverse / #Depending on your system use one line or the other #Ubuntu: #SetOutputFilter proxy-html #any other system: ProxyHTMLEnable On ProxyHTMLURLMap / /asset/ </Location> ...which doesn't seem to work. Comments, hints and ideas welcome!

  Read the article

• How to use AD/GPO/Print Services to "push out" a new printer driver to replace a broken one? How did my server get a broken driver?

  - by Zac B

  Context: We have an AD/GPO-managed corporate network with a little over a hundred PCs running Windows 7 x64, and a few managed printers. Our Server2008R2 primary domain controller is configured as a print server for them all. Problem: After a recent windows update and restart (no printer driver updates were included) on the DC, a particular shared printer (Lexmark T650) has begin exhibiting some strange behavior. First, it prints a preceding and following blank page for almost every document, on jobs submitted by about half of client machines (no separator page is configured on the server or any of the clients I've seen). Second, whenever someone tries to access "Printing Preferences" on any client, they recieve the following error message (this happens everywhere, 100% of the time, and didn't happen before the update on the DC): Once they click "OK", the prefs screen appears (with no separator page selected) and everything seems fine. I'm not even sure if these two issues are related, but everyone seems affected by one or both of those issues. What I've Tried: I've been hesitant to un-deploy the problem printer, or remove it via GPO, as it's pretty heavily used. I've tried updating (via MS update and our internal WSUS server) client machines and the DC. No printer driver updates have appeared, and no number of updates or restarts on the server or the client seems to have achieved anything other than my boss getting grumpy that I'm bouncing the domain controller so often. I've tried deleting the drivers on the server, and re-installing them from the original source that has worked for the past year...no change. I've tried selecting "New Driver" for one of the shared printers on a client machine, running as domain admin, and pushed the latest driver found by MSupdate back up to the DC. This changed the version number of the driver recorded in the print server manager, but caused no change--on the client I pushed from, or on any other. The error still appears. Question: Why the heck is this happening? Obviously, I got a bad driver from somewhere, but how do I get rid of it? I don't know of any "roll back drivers" functionality for centrally managed print drivers like Windows offers for other devices. How would I a) get this issue resolved on a client, and b) push the fix to the other members of the domain?

  Read the article

• Display is slightly blurry on (native) 1920x1080 resolution

  - by Martin Tuskevicius

  I have a computer monitor that is approximately 23" in size. Its native resolution is 1920x1080, and Windows 7 will not allow it to be any higher. However, I cannot make the resolution a little lower as well. When I right-click on my desktop and select 'Screen resolution,' the vertical slider has only two options: 1920x1080 and 1280x720. There are no real problems that I am having besides the fact that the image is slightly blurry. I can easily make things out and see them, but I definitely feel that the image is not as clear as it could be. My graphics card is ATI Radeon HD 5450 and it has the latest graphics drivers installed. I've tried playing around with the AMD VISION Engine Control Center to see if I can change an option to make the image clearer, but I had no luck. I did find one odd thing, though. When I lowered the refresh rate from 60Hz to 50Hz, the image kind of "zoomed in" but it also became perfectly clear like I would expect it to look. The problem is that when I use 50Hz, the image zooms in a little on the center and I lose maybe an inch and a half of the screen (I do not see the bar at the top of applications, I do not see the Windows taskbar thing, etc). I figured if I could somehow zoom in so that the entire image fills the screen (not the slightly cropped version) then I would have the perfectly crisp image of 50Hz, and also the uncropped image of 60Hz. However, upon zooming in, the image began to look blurry again just like it did with 60Hz. So I am at a loss here. I do not know how to make the image look as clear as it should. I have the latest drivers (I updated them today) and I know that my monitor supports the resolution that I am trying to use. Has anybody experienced something like this before? I'd really appreciate any input - thanks! Update: I have figured out how to make the display look crisp! I set it to the 50Hz option, and then I changed the scaling through the monitor itself, rather than software. Now, however, I am finding that games look pretty bad because since it is clear, the lower quality really becomes apparent. I cannot run new games at 1080p, so I run them at the lowest resolution possible (1280x720, since it is the only other option offered, as I have mentioned). So I am wondering, is there a way to have Windows display more resolution options?

  Read the article

• Repair corrupt hard disk on Mac without install CD

  - by Sarah

  The hard disk of my late 2009 MacBook Pro appears to have become corrupted. I am traveling and do not have my install CD (and won't for several weeks, nor will I be anywhere near an Apple store). The hard disk is not the original, which failed in June 2011. It's some Hitachi replacement installed by IT. History: I was typing an email this afternoon, my computer suddenly started making soft clicking sounds and then froze. I was not moving around. I rebooted, which took a while. I heard more clicking sounds and the computer froze at least once again. It's now kind of working, with mdworker sucking up one CPU. There are no awkward hard drive sounds when I run Chrome or play music. However, when I launched Stickies, I found no trace of my saved Stickies. I ran a live disk verification from within Disk Utility, and it reported Problem: As reported, I don't have access to an installation disc and am nowhere near an area where I can get one for at least two weeks. I have the option of asking someone to go to some trouble and expense to get one for me, but I'm not sure it's worth it: I've read that I can use fsck from single-user mode to repair the disk. Should I just try this? Is it risky? I'm concerned that the clicky sound portends imminent (mechanical) hard drive failure, so it's not worth doing a silly repair. This hard disk is backed up, but I definitely won't be able to access the backup while traveling. I'd like to maximize the probability that I can keep using my computer (and all its current files) while traveling. Update I bit the bullet and ran fsck -fy from single-user mode. It only needed one pass (modification) to reach the "okay" stage. However, rebooting took nearly 5 min and involved several rounds of scratchy sounds and a few bad clicks. I'm now back to kind of using my computer (the same files are missing as before). When I ran live disk verification from Disk Utility this time, however, it reported that the volume appears to be OK. Am I right to infer from the scratchy sounds, however, that my hard drive is still rapidly on its way out? Is there anything else I can do to increase its functionality over the next few weeks?

  Read the article

• BlueScreens on my ThinkPad with Windows 7 64 Bit and a SSD (CRITICAL_OBJECT_TERMINATION, ntoskernel.exe)

  - by pvorb

  I'm getting BlueScreens about every five days for more than three months. Here's an example: A problem has been detected and Windows has been shut down to prevent damage to your computer. The problem seems to be caused by the following file: ntoskrnl.exe CRITICAL_OBJECT_TERMINATION If this is the first time you've seen this stop error screen, restart your computer. If this screen appears again, follow these steps: Check to make sure any new hardware or software is properly installed. If this is a new installation, ask your hardware or software manufacturer for any Windows updates you might need. If problems continue, disable or remove any newly installed hardware or software. Disable BIOS memory options such as caching or shadowing. If you need to use safe mode to remove or disable components, restart your computer, press F8 to select Advanced Startup Options, and then select Safe Mode. Technical Information: *** STOP: 0x000000f4 (0x0000000000000003, 0xfffffa80065f2b30, 0xfffffa80065f2e10, 0xfffff80002f9bf40) *** ntoskrnl.exe - Address 0xfffff80002c98d00 base at 0xfffff80002c19000 DateStamp 0x4d9fdd5b It's has always been the same BlueScreen message showing CRITICAL_OBJECT_TERMINATION, 0x000000f4, and ntoskrnl.exe. Of course the addresses change. My computer is a ThinkPad T400 (about 2 years old) with a SSD in it. I'm also running Windows 7 Professional 64 bit. When I bought my computer, it had a 250GByte SeaGate HDD in it, which I replaced by a 500GByte HDD by Western Digital. Last september I bought a Corsair F120 SSD and replaced the HDD by this SSD. Then I bought a LEICKE HDD adapter for the UltraBay II where I plugged in my 500GByte HDD. This configuration ran about half a year without any errors. After re-installing Windows this spring, I am getting regular BlueScreens. Sometimes my system runs for about 2 weeks without a BSOD, sometimes I get several BlueScreens a day. The only thing that I noticed is, that I'm always running Google Chrome when it happens. Is there anyone who has made his/her own bad experiences whith some of my components or is there anybody who can tell me if it would be helpful to send my notebook to Lenovo? Thank you very much for your help on my issue! Regards, Paul

  Read the article

• SQLS Timeouts - High Reads in Profiler

  - by lb01

  Hi I've audited a SQLS2008 server with Profiler for one day.. the overhead didn't seem to trouble this new client my company has. They are using a legacy VB6 application as a front-end. They're experiencing timeouts once SQLS RAM usage is high. The server is currently running x64 sqls2008 on a VM with nearly 9 GB of RAM. SQL Server's 'max server memory option' is currently set to 6GB. I've put the results of the trace in a table and queried them using this query. SELECT TextData, ApplicationName, Reads FROM [TraceWednesday] WHERE textdata is not null and EventClass = 12 GROUP BY TextData, ApplicationName, Reads ORDER BY Reads DESC As I expected, some values are very high. Top Reads, in pages. 2504188 1965910 1445636 1252433 1239108 1210153 1088580 1072725 Am I correct in thinking that the top one (2504188 pages) is 20033504 KB, which then is roughly ~20'000 MB, 20GB? These queries are often executed and can take quite some time to run. Eventually RAM is used up because of the cache fattening, and timeouts occur once SQL cannot 'splash' pages in the buffer pool as much. Costs go up. Am I correct in my understanding? I've read that I should tune the associated T-SQL and create appropriate indices. Obviously cutting down the I/O would make SQL Server use less RAM. OR, maybe it might just slow down the process of chewing up the whole RAM. If a lot less pages are read, maybe it'll all run much better even when usage is high? (less time swapping, etc.) Currently, our only option is to restart SQL once a week when RAM usage is high, suddenly the timeouts disappear. SQL breathes again. I'm sure lots of DBAs have been in this situation.. I'm asking before I start digging out all of the bad T-SQL and put indices here and there, is there is something else I can do? Any advice except from what I know (not much yet..) Much appreciated. Leo.

  Read the article

• OEM sound card with no drivers or support

  - by randy

  I thought my sound card was going out so I bought a sound card online. Everything seemed to work ok, I do have sound. But after a few months, I noticed the extra software that downloaded with the sound card drivers didn't work. I ended up contacting creative and after a month of e-mail support, they asked for the serial number and/or model number. Their reply back was I had purchased an OEM sound card and they could not provide support for that, and informed me that that is why their drivers and software didn't work. They informed me that I had to contact the company that distributed the sound card and install their software. Is there anything I can do to find out who distributed this sound card, or is there anything I can do to get other features to work? I have 4 speakers and a sub but only 2 speakers produce sound. The only control I have is the volume. Creative's driver update program will find my sound card, download updates and even added software, but if I try to click on a downloaded program like Creative's Toolbox or Media Center, I get an error that it cannot find the devise. That is why I contacted creative in the first place. EDIT Thanks for the responses everyone. Here's an update. I thought I'd go thru my old computer stuff for my classes at school. I have a lot of old stuff saved, boxes and cables and stuff. I found the box the sound card came in. It looks like a box you'd buy at the store, like Best Buy or CompUSA. I worked with creative for such a long time, it went past the point of being able to return it to the junk online store this shipped from. The box did have an install CD, so I thought I'd start over to reinstall the drivers and software that shipped with the card. I noticed that the install would uninstall a program, then reinstall it. so I thought things were working out. But no good. Everything still works but the programs were still bad. I'd get an error trying to load them - not found. I'll look on the card the next time I get a chance and see if I can spot any kind of name on it.

  Read the article

• Ubuntu + SSL ports + AVAST

  - by jurajvt

  I have an interesting problem with communication via standard SSL ports. Fresh installed Ubuntu 14.04 server + Postfix + Dovecot, SASL authentication provided by Dovecot, self-signed certificate generated trough the Dovecot script mkcert.sh. Redirected ports on ZyWALL USG 200. I can send and receive e-mails from outside with standard ports 25 and 110, but not over 587. I am connecting to my server from machine with Windows 8.1 + VMWare Player + Ubuntu 14.04 Desktop + ssh. On Windows host I have installed Avast! antivirus. When I am trying to telnet from virtual machine to server over 587, it refused connection. But when I turn on Avast! it let me in to message Connected to... Same with nmap. When Avast! is turned on it is show me all SSL ports. When I turned it off, only standard ports appeared. OpenSSL shows me CONNECTED(00000003). But outside virtual machine directly in Windows 8.1 using nmap with zenmap there are not opened SSL ports in both Avast! states. From other external linux machines are problems with touching SSL ports same - refused. I have turned on submission in master.cf and 587 port is correctly listening on 0.0.0.0 in process master.pid which belongs to Postfix. I can telnet, or nmap over port 587 to my domain directly from server. Other ports like 995, 993 are OK on localhost, too. It is true, that I can't send emails via 587 anyway (Avast! turned on/off), but I can see ports opened. It is possible, that I have simply bad certificate and Avast! has right one, so with turned it on I can see opened ports? EDIT: To be more clear, I can't see or using port 587 everywhere from outside (tried Thunderbird, telnet, openssl, nmap, putty, swaks; both from Linux or Windows machines) and that is my problem. It was only by chance that I saw opened ports when Avast! is turned on.

  Read the article

• Can't recover hard drive

  - by BreezyChick89

  My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

  Read the article

• SQL Express 2008 R2 on Amazon EC2 instance: tons of free memory, poor performance

  - by gravyface

  The old SQL Express 2005 was running on a low-end single Xeon CPU Dell server, RAID 5 7200 disks, 2 GB RAM (SBS 2003). I have not done any baseline measurements on the old physical server, but the Web app is used by half a dozen people (maybe 2 concurrently), so I figured "how bad can an Amazon EC2 instance be?". It's pretty horrible: a difference of 8 seconds of load time on one screen. First of all, I'm not a SQL guru, but here's what I've tried: Had a Small Instance, now running a c1.medium (High Cpu Medium) Windows 2008 32-bit R2 EBS-backed instance running IIS 7.5 and SQL Express 2008 R2. No noticeable improvement. Changed Page File from fixed 256 to Automatic. Setup a Striped Mirror from within Disk Management with two attached 1 GB EBS volumes. Moved database and transaction log, left everything else on the boot EBS volume. No noticeable change. Looked at memory, ~1000 MB of physical memory free (1.7 GB total). Changed SQL instance to use a minimum of 1024 RAM; restarted server, no change in memory usage. SQL still only using ~28MB of RAM(!). So I'm thinking: this database is tiny (28MB), why isn't the whole thing cached in RAM? Surely that would speed up performance. The transaction log is 241 MB. Seems kind of large in comparison -- has this not been committed? Is it a cause of performance degradation? I recall something about Recovery Models and log sizes somewhere in my travels, but not positive. Another thing: the old server was running SQL Express 2005. Not sure if that has any impact, but I tried changing the compatibility level from SQL 2000 to 2008, but that had no effect. Anyways, what else can I try here? Seems ridiculous to throw more virtual hardware at this thing. I know I/O is going to be rough on EBS volumes, but surely others are successfully running small .NET/SQL apps on reasonably priced instances?

  Read the article

• Need help troubleshooting highly variable ping times

  - by Elliot.Bradshaw

  I'm at work using Citrix (think Remote Desktop) to connect to client sites. With my job I have to write a fair bit of code while I'm connected remotely via Citrix, so the latency of my internet connection is important. If I'm getting ping times above 250ms, then it becomes almost impossible to scroll, click or type with accuracy. Recently my Comcast business internet has been exhibiting highly variable ping times. If I ping google.com, I'll get pings that range from 9ms all the way up to 1300ms. The problem seems to be at its worst during the hours of 1PM to 4:30PM. Outside of those hours and the variance in pings settles down, mostly between 9ms and 50ms. The signal to noise ratio and upstream power are both fine on my modem--the values are here: http://pastebin.com/D4hWGPXf I ran a trace route from my computer to google.com (the results of which are here: http://pastebin.com/GcdjYvMh) and did another test ping to the IP of the first hop outside of our local network (73.98.44.1)--the variance in ping times existed in exactly the same manner as if I were pinging Google. Connecting directly to the cable modem by CAT5 makes no difference. Here is a screenshot demonstrating the variance of the ping times: http://postimage.org/image/haocdeauv/full/ -- as you can see it can get pretty bad. Three Comcast techs have been out (two of them were here when the problem wasn't happening) and they as well as the regional tier 2 Comcast support were unable to diagnose the problem. I now have a ticket open with tier 3 support, but have yet to hear back from them. Does anyone know what could cause these sorts of problems or have any idea from the traceroute above where it could be originating? The regional tier 2 guy tried to tell me that what I'm seeing is normal--are highly variable ping times like that ever acceptable? Anything I should ask Comcast to do or look at to get this problem fixed? Any tips/advice much appreciated! Edit: This is Comcast cable internet at a small start-up, we've ruled out congestion in our private LAN as a cause (i.e., no one's watching YouTube when the pings become variable). Update: Tier 3 Comcast support advised swapping out the modem, a tech came here today and did that--same problem persists.

  Read the article

• Proper set up shared folders for users

  - by user221486

  First I would like to say thanks for helping, and I have huge problem with proper set up permission for shared folders. I have Windows 7 x64 ent. - name: backupfb - added to domain with shared folder on drive e: (e:\backup) 50 clients/laptops with TSM Tivoli fastback for workstations who save files on shared folder And I need to configure proper permission for my shared folders that only owner of folder can access to their folders. Folder structure is: e:\backup <- shared as a "backup" folder \\backupfb\backup\ e:\backup\BackupAdmin <-- directory is used by the Tivoli Storage Manager FastBack for Workstations client to download revisions and configurations. Nodes require read-only access to these directories e:\backup\RealTimeBackup <-- enable client accounts to create directories that are only accessible by the account that created them. As a result, the directory that contains data for a node is not created until that node connects to the server. So permission should look like that (take from instructions): Inheritable permissions from object`s parents are DISABLE Permission entries: \\backupfb\backup\BackupAdmin Allow Users Read, Execute This folder, subfolders, and files Traverse Folder / Execute Allow List Folder / Read Data Allow Read Attributes Allow Read Extended Attributes Allow Delete subfolders and files Allow Delete Allow Read Permission’s Allow Allow Administrators Full Control This folder, subfolders, and files Both folders have enabled option "apply these permissions to objects and/or containers within this container only" Here everything works fine \\backupfb\backup\RealTimeBackup <<-- Allow Administrators Full Control This folder, subfolders, and files Allow CREATOR OWNER Full Control This folder, subfolders, and files (from domain) Allow Users Special This folder only Traverse Folder / Execute Allow List Folder / Read Data Allow Read Attributes Allow Read Extended Attributes Allow Create Files / Write Data Allow Create Folders / Append Data Allow Delete subfolders and files Allow Read Permission’s Allow Allow OWNER RIGHTS* Full Control This folder, subfolders, and files Here I have huge problem with CREATOR OWNER Im able to set FULL CONTROL but I can only apply "Subfolders and files only". When I change props. to "This folder, subfolders and files" and save its change to "Subfolders and files only" So I try use icacls to set up permissions @echo off takeown /F E:\backup\ /R /A for /D %%i IN (E:\backup\RealTimeBackup*) DO icacls E:\backup\RealTimeBackup\%%~nxi /grant:r cloud\%%~nxi:F /T /C pause but after that user are able to create just one folder in \backupfb\backup\RealTimeBackup\userfolder but problem is with subfolders In log i have: FBW5022E Unable to access the specified file Explanation: The file specified is unable to be accessed. Possibly spelled incorrectly, or bad path, or permissions. User response: Ensure the user has the proper permissions for the file and directories involved andthat the file and directory exist Any idea ?? pls help ;-) thanks

  Read the article

• HP ProLiant DL380 G3 Running Windows Server 2000 has crashed between 6-7:30am for the past 5 days

  - by user109717

  I have a HP ProLiant DL380 G3 running Windows Server 2000 that has been crashing everyday between 6-730am. This started when I changed out a failing hard drive 6 days ago. I have looked at the scheduled tasks which does not have anything pertaining to this issue. Below are the only things I see in the system log and some of the dump files. Can this be a hardware issue if this happens at a certain time frame everyday? Any help is greatly appreciated. Thanks The previous system shutdown at 6:07:55 AM on 2/7/2012 was unexpected. System Information Agent: Health: The server is operational again. The server has previously been shutdown by the Automatic Server Recovery (ASR) feature and has just become operational again. [SNMP TRAP: 6025 in CPQHLTH.MIB] BugCheck 7A, {3, c0000005, 3400028, 0} Probably caused by : memory_corruption ( nt!MiMakeSystemAddressValidPfn+42 ) Followup: MachineOwner 0: kd !analyze -v * Bugcheck Analysis * * KERNEL_DATA_INPAGE_ERROR (7a) The requested page of kernel data could not be read in. Typically caused by a bad block in the paging file or disk controller error. Also see KERNEL_STACK_INPAGE_ERROR. If the error status is 0xC000000E, 0xC000009C, 0xC000009D or 0xC0000185, it means the disk subsystem has experienced a failure. If the error status is 0xC000009A, then it means the request failed because a filesystem failed to make forward progress. Arguments: Arg1: 00000003, lock type that was held (value 1,2,3, or PTE address) Arg2: c0000005, error status (normally i/o status code) Arg3: 03400028, current process (virtual address for lock type 3, or PTE) Arg4: 00000000, virtual address that could not be in-paged (or PTE contents if arg1 is a PTE address) MODULE_NAME: nt IMAGE_NAME: memory_corruption BugCheck A, {0, 2, 1, 804137d6} Probably caused by : ntkrnlmp.exe ( nt!CcGetVirtualAddress+ba ) * Bugcheck Analysis * * IRQL_NOT_LESS_OR_EQUAL (a) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If a kernel debugger is available get the stack backtrace. Arguments: Arg1: 00000000, memory referenced Arg2: 00000002, IRQL Arg3: 00000001, bitfield : bit 0 : value 0 = read operation, 1 = write operation bit 3 : value 0 = not an execute operation, 1 = execute operation (only on chips which support this level of status) Arg4: 804137d6, address which referenced memory MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe

  Read the article

• Silverlight 4 WCF RIA Services and MVVM is not as simple

  - by Thomas Jaskula

  [Disclaimer: I'm ASP.NET MVC Developer] Hi, I'm looking for some best practices with implementing MVVM pattern with WCF RIA in Silverlight 4. I'm not looking to use MEF of IoC for locating my ViewModels. What I would like to know is how to apply MVVM pattern with Silverlight 4 and WCF RIA. I don't want to use other stuff like Prism or MVVM Light toolkit. I found many examples on Internet showing how it is wonderful to drag and drop a datasource on the view and the job is done (it reminds me about my first VB6 developments). I tried to implement MVVM with WCF RIA and it's not strightforward at all. If I understand, the MVVM should contain all the logic in order to unit test it in isolation but when it comes to combine it with WCF RIA it's another story. I have the following questions. Can I use a generated metadata as model ? It would be easier to use it that if I write all from the scratch. As I saw the only way I could get data is through DomainContext or through direct binding in the view (local ressource). I don't want the direct binding in the view, not testable at all. On the other hand I can't use DomainContext, it doesn't expose any single entity !!! All I have is the EntitySet that I can bind to datagrid. How do I bind a single Entity to the DataForm from the ViewModel ? How do I udpate the model to the database ? How do I navigate from one Entity to a collection of it's itemps. For example if I have a Company Entity I would like to show a DataFrom to update a entite informations and a datagrid to show companies adresses. When saving a form would like to save information to Company and for example an information avout which adress was selected as active. Please help me understand how to do it well. Or maybe I should drop the WCF RIA and to do it with WCF from scratch ? What do you think ?

  Read the article

• Doing TDD Silverlight 4 RC using Visual Studio 2010 RC

  - by user133992

  First I am glad to see better TDD support in VS2010. Support for generating code stubs from my tests is ok - not as good as more mature TDD plug-ins but a good start. I am looking for some best Silverlight 4.0 TDD practices. First Question: Anyone have links, recommendations? I know the new Silverlight Unit Test capabilities are much better (Jeff Wilcox's Mix Presentation). What I am focusing on right now is using TDD to develop pure Silverlight 4.0 Class Library projects - projects without a Silverlight UI project. I've been able to get it to work but not as cleanly as it should be. I can create an Empty VS project. Add A Silverlight 4 Class Library Project. Add a TestProject (not a silverlight Unit Test Project but a plain Test Project). Add a simple test in the Test Project such as: namespace Calculator.Test { [TestClass] public class CalculatorTests { [TestMethod] public void CalulatorAddTest() { Calc c = new Calc(); int expected = 10; int actual = c.Add(6, 4); Assert.AreEqual<int>(expected, actual); } } } Using the new Generate Type and Method from Test feature it will generate the following code in the Silverlight Project: namespace Calculator { public class Calc { public int Add(int p, int p_2) { throw new NotImplementedException(); } } } When I run the tests the first time it says the target assembly is Silverlight and not able to run test - Not exact text but the same general idea. When I change the implementation to: namespace Calculator { public class Calc { public int Add(int p, int p_2) { return p + p_2; } } } and re-run the test, it works fine and the test goes green. It also works for all other TDD code I generate after. I also get a warning Mark in the Test Project's reference to the Calculator Silverlight Class Library Assembly. Second Question: Any comments ideas if this just a bug in VS2010 RC or is Silverlight Class Library TDD not really supported. I have not created a Silverlight UI project or changed and build or debug settings so I have no idea what is hosting the silverlight DLL. Finally, some of the Silverlight Class Libraries I need to write will provide functionality that requires elevated Out-Of-Browser rights. Based on the above, it looks like I can use TDD Test Projects against regular Silverlight 4.0 Class Libraries, but I have no idea how I can TDD the elevated OOB functionality without also creating the UI component that gets installed. The UI piece is not really needed for the Library development and gets in the way of what I actually want to TDD. I know I can (and will) mock some of that functionality but at some point I will also need the real thing in my tests. Third Question: Any ideas how to TDD Silverlight 4.0 Class Library project that requires OOB elevated rights? Thanks!

  Read the article

• ActiveDirectoryMembershipProvider and ADAM (or AD LDS) and SetPassword

  - by Iulian

  By the subject line it seems to be a rather broad subject and I need some help here. Basically what I want is to use ActiveDirectoryMembershipProvider with an ADAM instance to authenticate users in an ASP.NET web application. My development environment is a windows 7 machine with an AD LDS instance on it whilst the QA server is a Windows 2003 server with an ADAM instance on it. I have all the required users on both instances plus one with adminsitrator role (CN=Admin,CN=xxx,DC=xxx,C=xx) which I want to use as the connection user. Using connectonProtecton="None" connectionUsername="CN=Admin,CN=xxx,DC=xxx,C=xx" connectionPassword="xxx" I am able to authenticate on both environments (dev & qa). If I change to the connectionProtection to "Secure" I am not able to authenticate anymore; the error I get is "Parser Error Message: Unable to establish secure connection with the server" To me it sounds wrong to use connectionProtection="None" although I found on the net a lot of samples using this setting. Can I use connectionProtection="Secure" to connect to an ADAM instance using an account defined on that instance having Administrator role? What other choices do I have (like using an domain account)? What if my machine where I am to deploy the application is not a part of the domain, will this affect in any way the behavior? I am novice in the respect so I would really appreciate some clear answers or some directions as where to look? Now beside the "signing in" feature of the ActiveDirectoryMembershipProvider I also want to add an extra one, which is setting the password without knowing the old one (something that will be used by a "reset password" feature). So I added a couple of extension methods to the provider, and used System.DirectoryServices classes like DirectoryEntry and the like. When creating a directory entry I use the same credentials provided in web.config for the provider minus the AuthenticationType as I don't know what is right combination of the flags that corresponds to None/Secure. I am able to use Invoke "SetPassword" with ADS_OPTION_PASSWORD_METHOD option as ADS_PASSWORD_ENCODE_CLEAR on my dev machine (w/ AD LDS instance); nevertheless on qa environment (w/ ADAM instance) I am getting an error like "Exception Details: System.DirectoryServices.DirectoryServicesCOMException: An operations error occurred. (Exception from HRESULT: 0x80072020)" I am quite sure it is not about AD LDS vs ADAM but probably another configuration / permission issue. So can anyone help me with some hints on how to use this SetPassword feature? And as a general question what are the best practices when it comes to using ADAM regarding security, programming etc? Thanks in advance Iulian

  Read the article

• Loading a Page into a jQuery Dialog

  - by Dave

  I tend to follow a fairly "modular" approach to building applications and I recently started working with jQuery. The application I'm working on is going to be fairly large so I'm trying to break pieces out into separate files/modules when possible. One example of this is a "User Settings" dialog. This dialog has a form, a few tabs, and quite a good number of input fields so I want to develop it in a separate HTML file (PHP actually, but it can be considered HTML for the purposes of this example). It's an entire page in and of itself with all the tags you would expect such as: <html><head></head><body></body></html> So I can now develop, what I want to be, the dialog separate from the base application. This dialog has it's own Javascript (A LOT of Javascript, in fact) in the head as well, with jQuery $(document).ready(){} capturing, etc. Everything works flawlessly in isolation. However, when I attempt to load the jQuery modal dialog with the page (inside of the main application page), as one might expect, trouble ensues. Here's a brief, very simple, example of what it looks like: editUserDialog.load ("editUser.php", {id : $('#userList').val(), popup : "true"}, function () { editUserDialog.dialog ("option", "title" , "Edit User"); editUserDialog.dialog ('open'); }); (I'm passing in a "popup" flag to the page so that the page can determine its context -- i.e. as a page or inside of the jQuery dialog). Question 1: When I moved the code from the "head" into "body" (in the editUser.php page) it actually worked for the most part. It seemed that jQuery was calling the $(document).ready() function in the context of the body of the loaded file and not the head. Is this a bad idea? Question 2: Is my process for building this application just totally flawed to begin with? I've scoured the net to attempt to find a "best practices" sort of document to building reasonably large applications using jQuery/PHP without a lot of success so maybe there's something out there someone else is aware of that I've somehow missed. Thanks for bearing with me while I attempt to describe the issues I've encountered and I hope I've accurately described the problem.

  Read the article

< Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >