Search Results

Search found 17621 results on 705 pages for 'just my correct opinion'.

Page 501/705 | < Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >

• Cisco BVI: Claiming IP addresses

  - by cjavapro

  I would like to make sure I understand this correctly. Given a Cisco ISO router that is set up with a BVI (a variation of a bridge route).. and the following layout "ISP router" \ "Network switch" # nothing special here. | \ | \ | \ | \ "Router 1 with NAT" "Router 2 with BVI" If I understand correctly.. the outside of a BVI will only respond to IP addresses that have already been claimed on the inside of the BVI... example subnet is 123.123.123.??? and servers inside the BVI on 123.123.123.10 and 123.123.123.11, and the NAT router is holding a public IP address of 123.123.123.50. If a connection comes in to 123.123.123.10 it will be received by router 2 but if it is received on 123.123.123.50, it will be received by router 1 and not received by router 2. and if a connection comes in to 123.123.123.90 (does not exist) it will not be received by either router. Am I correct? Is it true that the BVI router will not even receive packets to IP addresses that it does not see as existing on the inside?

  Read the article

• Driver denied access to PCI card

  - by Corin

  Alright, I asked this on StackOverflow (here) and they suggested trying ServerFault to get help on permissions. So here's the deal. We designed a custom PCI card and wrote the driver for it. It's been working for years without problems but now we encountered one particular installation were it doesn't work. The problem is that we cannot connect to the PCI to begin communication with it. We tried replacing the card and had the same problem. We had the motherboard replaced thinking the PCI slots were bad. That didn't help either. We tried the cards in a different computer and they all worked. So it seemed to be something specific to the computer. The Windows Device Manager indicates the device is working properly and seems to have all the correct driver info. We now have this troublesome computer back at the office for testing. With the help of some extra debug info in the driver we determined that we cannot connect because access is denied. Sounds like a permissions issue to me. I should note that we are logged into the system as a local administrator. So what configuration option in Windows can prevent access to a device?

  Read the article

• Route through site-to-site VPN not working

  - by Jonathan

  I'm trying to set up a site-to-site VPN using RRAS on two 2K8r2 servers since yesterday. The connection is working at this point, but I can't get it to send traffic from one site to the other one. Set up: the set up is the same on both sites: the server is connected to a router that's connected to a modem. The routers act like a DHCP-server and assign IP addresses from the range subnet.21-subnet-.100. Both servers use a static IP address, subnet.11, and are set up as DMZ. Configuration: the servers are configured using the wizard to set up a site-to-site connection. This works with a demand-dial interface and a PPTP VPN connection. As mentioned, the VPN connection work properly. Problem: I can't get the servers to send the traffic for the other site, to be sent through the VPN connection. I added a static route on both server (home, office 1) and I can see the result in the IP routing table (home, office 1). I did this because the route didn't show up automatically. My guess is that this last step isn't right, for example because the routing table states "non demand-dial", which seems not correct. Home: Subnet: 10.0.1.0/24 Router: 10.0.1.1 Server: 10.0.1.11 (DMZ) DHCP: 10.0.1.21-10.0.1.100 RRAS DHCP: 10.0.1.101-10.0.1.150 Office 1: Subnet: 10.0.2.0/24 Router: 10.0.2.1 Server: 10.0.2.11 (DMZ) DHCP: 10.0.2.21-10.0.2.100 RRAS DHCP: 10.0.2.101-10.0.2.150 I hope someone has an idea to get this route working!

  Read the article

• Prevent Amazon EC2 Time zone from reverting back on yum update

  - by D.Tate

  I use an Amazon EC2 server instance that runs a distro called Amazon Linux AMI. (I've read that it is based on CentOS/Red Hat). My specific version is the 2012.09 release. Anyway, I was able to change the time zone about a week ago from the default UTC to America/New_York (which is EST/EDT). The command I used to change it was: ln -sf /usr/share/zoneinfo/America/New_York /etc/localtime ...thanks to this other Server Fault question. At that point, I was able to run date from the the command line, and it correctly displayed the EDT time. And even after EDT "fell back" to EST this past Sunday, I was pleased to find that running date still produced the correct local time. So that was great. However, after running a yum update yesterday, it seems that my time zone got reverted back to plain 'ol UTC. I even checked the last modified time of /etc/localtime file, and indeed it confirmed that it had been modified around the same time I had updated. Is there any way to prevent this from happening again, or will I be stuck resetting the time zone every time I do a yum update?

  Read the article

• Accidentally dd'ed an image to wrong drive / overwrote partition table + NTFS partition start

  - by Kento Locatelli

  I screwed up and set the wrong output for dd when trying to copy a freenas iso, overwriting the wrong external hard drive. Ironically, I was trying to setup a freenas server for data backup... External drive is only used for data storage, system is entirely intact Drive had a single NTFS partition filing the entire device (2TB WD elements) Drive originally had an MBR partition table. Drive now shows as having a GPT, presumably from the freenas image. Drive was mounted at the time, with maybe a couple kB of data written/read after running dd Drive is just a few months old and healthy (regular SMART / fs checks) I have not reboot the OS (crunchbang) /proc/partition still holds the correct information (and has been stored) Have dd's output (records in / out / bytes) testdrive did not find any partitions on quick or deep search running photorec to recover the more important data (a couple recent plaintext files that hadn't been backed up yet). Vast majority of disk content ( 80%) is unnecessary media files. My current plan is to let photorec do it's thing, then recreate the mbr with gparted and use cfdisk to create another NTFS partition using the sector information from /sys/block/.../. Is that a good course of action (that is, a chance of success)? Or anything else I should try first? Possibly relevant information: dd if=FreeNAS-8.0.4-RELEASE-p3-x86.iso of=/dev/sdc: 194568+0 records in 194568+0 records out 99618816 bytes (100 MB) copied grep . /sys/block/sdc/sdc*/{start,size}: /sys/block/sdc/sdc1/start:2048 /sys/block/sdc/sdc1/size:3907022848 cat /proc/partitions: major minor #blocks name ** Snipped ** 8 32 1953512448 sdc 8 33 1953511424 sdc1 current fdisk -l output: WARNING: GPT (GUID Partition Table) detected on '/dev/sdc'! The util fdisk doesn't support GPT. Use GNU Parted. Disk /dev/sdc: 2000.4 GB, 2000396746752 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/sdc doesn't contain a valid partition table

  Read the article

• How can I make non-anti-aliased text look good in Firefox on Mac OS X?

  - by cosmic.osmo

  After being a Windows user for the last 10 years, I got a MacBook Pro, which I'm working on configuring to my liking. I find small-size anti-aliased text to be blurry and hard to read, so I typically disable it. I've found the settings in the General Control Panel, and used TinkerTool to increase the anti-alias threshold size to 18pt. Mac OS X and other applications appear to respect these settings. A problem appears when I use Firefox. By default, it's configured to ignore the Mac OS anti-alias settings. This is changed by going to about:config, and setting gfx.use_text_smoothing_setting = true (default is false). However, even with this setting, it appears Firefox is still rendering the fonts under the assumption that they will be anti-aliased, which results in very odd and uneven spacing, as you can see in this example (pay attention to the placement of the "s" in "Disable"): With anti-aliasing: Without anti-aliasing: How can I configure Firefox to both not use anti-aliasing and to use correct font spacing? I'm using Mac OS X Lion and Firefox 5.

  Read the article

• How do I log back into a Windows Server 2003 guest OS after Hyper-V integration services installs and breaks my domain logins?

  - by Warren P

  After installing Hyper-V integration services, I appear to have a problem with logging in to my Windows Server 2003 virtual machine. Incorrect passwords and logins give the usual error message, but a correct login/password gives me this message: Windows cannot connect to the domain, either because the domain controller is down or otherwise unavailable, or because your computer account was not found. Please try again later. If this message continues to appear, contact your system administrator for assistance. Nothing pleases me more than Microsoft telling me (the ersatz system administrator) to contact my system administrator for help, when I suspect that I'm hooped. The virtual machine has a valid network connection, and has decided to invalidate all my previous logins on this account, so I can't log in and remotely fix anything, and I can't remotely connect to it from outside either. This appears to be a catch 22. Unfortunately I don't know any non-domain local logins for this virtual machine, so I suspect I am basically hooped, or that I need ophcrack. is there any alternative to ophcrack? Second and related question; I used Disk2VHD to do the conversion, and I could log in fine several times, until after the Hyper-V integration services were installed, then suddenly this happens and I can't log in now - was there something I did wrong? I can't get networking working inside the VM BEFORE I install integration services, and at the very moment that integration services is being installed, I'm getting locked out like this. I probably should always know the local login of any machine I'm upgrading so I don't get stuck like this in the future.... great. Now I am reminded again of this.

  Read the article

• VLAN Tagging Traffic on Cisco Switch

  - by David W

  I have a situation where I'm setting up multiple VLANS on a pfSense firewall on the same physical interface for a client. So in pfSense, I now have VLAN 100 (employees) and VLAN 200 (students - student computer lab). Downstream from pfSense, I have a Cisco SG200 switch, and coming off of the SG200 is the student lab (running on a Catalyst 2950. Yes, that's old, but it works, and this is a poor nonprofit we're talking about). What I'd like to do is tag everything on the network as VLAN 100, except for the student computer lab. Earlier today when I was on-site with the client, I went into to the old Catalyst 2950, and assigned all of its ports to access VLAN 200 (switchport mode access vlan 200) without setting up a trunk on the Catalyst or on the SG200. Looking back on it, I now understand why internet in the lab broke. I reverted the lab back to the default VLAN1 (we're still running on a different firewall - we haven't deployed pfSense -, and the traffic is still separated physically). So my question is, what do I need to do in order to properly deploy this scenario? I believe the correct answer is: Ensure VLANs 100 and 200 are setup in pfSense, and that DHCP is operating correctly (on separate subnets) Setup a trunkport VLAN that allows both 100 & 200 traffic, and plug that port directly into pfSense. Setup a VLAN 200 trunkport on the SG200 (It's not running iOS, but if it were, the command would be switchport trunk native vlan 200), which will then plug into the Catalyst 2950. Setup a VLAN 200 trunkport on the Catalyst 2950 (that is plugged into the SG200 VLAN200 port with the same command - switchport trunk native vlan 200) Setup the rest of the ports on the old Catalyst 2950 in the lab to be access ports on VLAN200. Is there anything that I'm missing, or do I need to tweak any of these steps, in order to properly segment the network traffic?

  Read the article

• Quota, AD and C#

  - by Gnial0id

  At first, my mother tongue is not English, so I apologize for the possible mistakes. I'm working on a WS2008R2 server with an Active Directory and a web platform manages this AD with C# code. A group of users have to be able to create user accounts but during the procedure, a disk quota for this new account is (and have to be) created. As the "creator" must not be a member of the Administrators group, the access to the c/: disk is denied. So, I want to perform the File Server Resource Manager operations with C# code by an non-admin account. The code is correct, it works normally with admin account. So, the problem turns around the permissions on the hard drive. I've looked after help on the Internet, without success. It seems that quota delegation is impossible. Only admin can perform this. A colleague helped me a bit, and found the GPO "By pass traverse checking" on a forum but it doesn't seems to be the good way. Any help would be appreciate.

  Read the article

• User authentication -- username mismatch in IIS in ASP.NET application

  - by Cory Larson

  Last week, an employee's Active Directory username was changed (or a new one was created for them). For the purposes of this example, let's assume these usernames: Old: Domain\11111 New: Domain\22222 When this user now logs in using their new username, and attempts to browse to any one of a number of ASP.NET applications using only Windows Authentication (no Anonymous enabled), the system authenticates but our next layer of database-driven permissions prevents them from being authorized. We tracked it down to a mismatch of usernames between their logon account and who IIS thinks they are. Below are the outputs of several ASP.NET variables from apps running in a Windows 2008 IIS7.5 environment: Request.ServerVariables["AUTH_TYPE"]: Negotiate Request.ServerVariables["AUTH_USER"]: Domain\11111 Request.ServerVariables["LOGON_USER"]: Domain\22222 Request.ServerVariables["REMOTE_USER"]: Domain\11111 HttpContext.Current.User.Identity.Name: Domain\11111 System.Threading.Thread.CurrentPrincipal.Identity.Name: Domain\11111 From the above, I can see that only the LOGON_USER server variable has the correct value, which is the account the user used to log on to their machine. However, we use the "AUTH_USER" variable for looking up the database permissions. In a separate testing environment (completely different server: Windows 2003, IIS6), all of the above variables show "Domain\22222". So this seems to be a server-specific issue, like the credentials are somehow getting cached either on their machine or on the server (the former seems more plausible). So the question is: how do I confirm whether it's the user's machine or the server that is botching the request? How should I go about fixing this? I looked at the following two resources and will be giving the first one a try shortly: http://www.interworks.com/blogs/jvalente/2010/02/02/removing-saved-credentials-passwords-windows-xp-windows-vista-or-windows-7 http://stackoverflow.com/questions/2325005/classic-asp-request-servervariableslogon-user-returning-wrong-username/5299080#5299080 Thanks.

  Read the article

• Exchange 2003: recover mailbox when migrated to 2007

  - by lyngsie

  We have migrated almost all of our mailboxes from Exchange 2003 to 2007 so both are still up and co-existing in our domain. One mailbox is missing some mails, and I tried to recover from an Exchange 2003 backup using ExMerge as usual, but it throws an error: Error opening message store (MSEMS). Verify that the Microsoft Exchange Information Store service is running and that you have the correct permissions to log on. (0x8004011d) This should be normal when a mailbox has been migrated to 2007 and you try to recover a 2003 backup as stated here: http://www.petri.co.il/restoring-exchange-2003-mailboxes-exchange-2007-exmerge.htm We then tried the solution given in the article (copying the value "homemdb" for the user and pasting this in "msExchOrigMDB" for the Recovery Storage Group object in adsiedit). The error unfortuntely persists. So my question is, how can I extract a .pst from a mailbox in the recovery storage group when both Exchange 2003 and 2007 are running? I assume this is why the solution in the article didn't work. If no solution is possible using regular tools (exmerge, eseutil, etc.) which third-party tool should we choose - preferably the cheapest as we only need this one mailbox recovered.

  Read the article

• ffmpeg: video file played OK on Ubuntu, but no sound on XP

  - by Andy Le

  I created a video clip using ffmpeg (vcodec: mpeg2video, acodec: AC3 5.1). The file can be played normally on Ubuntu, but when I play it on an XP machine, there is no sound. I can play AC3 files and other movies with AC3 sound. I already tried many codec packs and many players. When I compare the MediaInfo tab of the Properties window of the file with another playable movie, I see that the Audio Identifier of the audio stream in my file is 0x80 while it is 0x02 in the other movie. So I guess that's why players on XP can't recognize the audio codec. When I use an MKV container instead of MPEG (still mpeg2video codec), then the result is OK on both Ubuntu and XP (with the correct Audio ID). I really need MPEG though. Any idea? This is the command I used: ~/ffmpeg/ffmpeg/ffmpeg -loop_input \ -t 97 -r 30000/1001 -i v%4d.tga -i final.ac3 \ -vcodec mpeg2video -qscale 1 -s 400x400 -r 30000/1001 \ -acodec copy -y out6.mpeg 2 This is the output of mediainfo (on Ubuntu): General Complete name : out6.mpeg Format : MPEG-PS File size : 6.86 MiB Duration : 1mn 37s Overall bit rate : 593 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@Main Format settings, BVOP : No Format settings, Matrix : Default Format_Settings_GOP : M=1, N=12 Duration : 1mn 37s Bit rate mode : Variable Bit rate : 122 Kbps Width : 400 pixels Height : 400 pixels Display aspect ratio : 1.000 Frame rate : 29.970 fps Resolution : 8 bits Colorimetry : 4:2:0 Scan type : Progressive Bits/(Pixel*Frame) : 0.025 Stream size : 1.41 MiB (21%) Audio ID : 128 (0x80) Format : AC-3 Format/Info : Audio Coding 3 Duration : 1mn 36s Bit rate mode : Constant Bit rate : 448 Kbps Channel(s) : 6 channels Channel positions : Front: L C R, Side: L R, LFE Sampling rate : 44.1 KHz Stream size : 5.18 MiB (75%)

  Read the article

• How best to manage my growing data in Excel?

  - by Mike

  This isn't a question about formulas or features in Excel. I'm debating the correct/best way to manage the growing amount of data 'I have to' manage in Excel (I produce PIVOT tables/reports for my management). DATA: I record the number of publications we order: cost, date ordered, start and end of subscription, who requested it, when they ordered it, when I ordered it, will it be cancelled next year, etc, etc, etc. DILEMMA: Obviously we re-order a lot of the same publications, so depending on how I manage the data I could be duplicating all over the place. OPTION 1: So, do I use ROWs = publication name in Row 1 and all the related columns for each financial year are copied and pasted after each financial year ready for the new FY information? This will lead to me going to column ZZ. OPTION 2: Or, do I use COLUMNs = each row has only one FY information for each publication and if we re-order or cancel a publication I re-type the publication name in a row below and fill in appropriate columns? This will lead to a long list of publications down to row 10000, and potential for misspelling of repeat ordered publication names. IDEAS: What's the best way - thinking in terms of pivot table best practice, being able to sum or count easy, report formatting, etc. Any best practices much appreciated.

  Read the article

• Apache Mod SVN Access Forbidden

  - by Cerin

  How do you resolve the error svn: access to '/repos/!svn/vcc/default' forbidden? I recently upgraded a Fedora 13 server to 16, and now I'm trying to debug an access error with a Subversion server running on using Apache with mod_dav_svn. Running: svn ls http://myserver/repos/myproject/trunk Lists the correct files. But when I go to commit, I get the error: svn: access to '/repos/!svn/vcc/default' forbidden My Apache virtualhost for svn is: <VirtualHost *:80> ServerName svn.mydomain.com ServerAlias svn DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <Location /repos> Order allow,deny Allow from all DAV svn SVNPath /var/svn/repos SVNAutoversioning On # Authenticate with Kerberos AuthType Kerberos AuthName "Subversion Repository" KrbAuthRealms mydomain.com Krb5KeyTab /etc/httpd/conf/krb5.HTTP.keytab # Get people from LDAP AuthLDAPUrl ldap://ldap.mydomain.com/ou=people,dc=mydomain,dc=corp?uid # For any operations other than these, require an authenticated user. <LimitExcept GET PROPFIND OPTIONS REPORT> Require valid-user </LimitExcept> </Location> </VirtualHost> What's causing this error? EDIT: In my /var/log/httpd/error_log I'm seeing a lot of these: [Fri Jun 22 13:22:51 2012] [error] [client 10.157.10.144] ModSecurity: Warning. Operator LT matched 20 at TX:inbound_anomaly_score. [file "/etc/httpd/modsecurity.d/base_rules/modsecurity_crs_60_correlation.conf"] [line "31"] [msg "Inbound Anomaly Score (Total Inbound Score: 15, SQLi=, XSS=): Method is not allowed by policy"] [hostname "svn.mydomain.com"] [uri "/repos/!svn/act/0510a2b7-9bbe-4f8c-b928-406f6ac38ff2"] [unique_id "T@Sp638DCAEBBCyGfioAAABK"] I'm not entirely sure how to read this, but I'm interpreting "Method is not allowed by policy" as meaning that there's some security Apache module that might be blocking access. How do I change this?

  Read the article

• Saving a file in a CSV type in Excel always removes the BOM

  - by rickp

  I've been trying to find a reasonable solution/explanation (unsuccessfully) to find out why Excel defaults to removing the BOM when saving a file to the CSV type. Please forgive me if you find this a duplicate of this question. This handles reading CSV files with non-ASCII encoding, but it doesn't cover saving the file back out (which is where the biggest issue lies). Here is my current situation (which I'm going to gather is common among localized software dealing with Unicode characters and a CSV format): We export data to a CSV format using UTF-16LE, ensuring the BOM is set (0xFFFE). We validate after the file is generated with a Hex editor to ensure it was set correctly. Open the file in Excel (for this example we're exporting Japanese characters) and witness that Excel handles loading the file with the correct encoding. Attempts to save this file will prompt you with a warning message indicating that the file may contain features that may not be compatible with Unicode encoding, but asks if you'd like to save anyway. If you select the Save As dialog, it will immediately ask you to save the file as "Unicode Text" rather than CSV. If you select the "CSV" extension and save the file it removes the BOM (obviously along with all the Japanese characters). Why would this happen? Is there a solution to this problem, or is this a known 'bug'/limitation of Excel? Additionally (as a side issue) it appears that Excel, when loading UTF-16LE encoded CSV files, only uses TAB delimiters. Again, is this another known 'bug'/limitation of Excel?

  Read the article

• Unable to connect to Windows VPN from iPad

  - by Justin

  I have a 16 GB iPad wifi I can't get to connect to VPN. The error I get is: "A connection could not be established to the PP server. Try reconnecting. If the problem continues, verify your settings and contact your Administrator." I have tried a variety of tasks to troubleshoot the issue: I have verified that another iPad on another network can connect to the VPN I am trying to connect to I can connect to this VPN from the same network the iPad uses on a Windows machine I have verified an iPhone user can connect to this VPN from a different network I have reset the iPad's network settings I have reset the entire iPad and restored settings I have compared my settings w/ a screenshot from the iPad that works and confirmed everything is correct I have used the IP address and domain name of our VPN server in the settings I have tried deleting the VPN settings in the iPad and recreating them I have verified in the logs of VPN server that I'm not even getting to the VPN server (no log entry) I have verified that I cannot VPN from the iPad on separate network (different ISP and router) Are there any other ways to troubleshoot VPN on an iPad?

  Read the article

• Acrobat 9 Pro - shortcut key failure

  - by Rick G

  I create numerous Acrobat PDF files from MS Word documents via Acrobat 9 Pro. I often need to print a single page from an Acrobat PDF file. I normally use the keyboard shortcut Control-P (Print Dialog) and ALT-U (current page). I recently set up a new PC with Windows 7, and this shortcut combination does not work. When I press ALT-U, it moves the highlight to the correct item, but does not select the radio button. If I press the Enter key, then I print the entire document instead of the current page - VERY annoying! It looks like there is an error in the design of the Print dialog for Acrobat. There are two items which have ALT-U as the keyboard shortcut. They are "Current page" in the Print range frame, and "Summarize comments". I have been able to use Control-P (Print Dialog) and ALT-U (current page) with no problems on virtual machines and older computers running Windows XP. Maybe I installed some software on the new PC that is messing up the keyboard shortcut. Is there any way to figure out the culprit - or is this a known problem with Acrobat?

  Read the article

• Why cache static files with Varnish, why not pass

  - by Saif Bechan

  I have a system runnning nginx / php-fpm / varnish / wordpress and amazon s3. Now I have looked at a lot of configuration files while setting up the system, and in all of them I found something like this: /* If the request is for pictures, javascript, css, etc */ if (req.url ~ "\.(jpg|jpeg|png|gif|css|js)$") { /* Remove the cookie and make the request static */ unset req.http.cookie; return (lookup); } I do not understand why this is done. Most of the examples also run NginX as a webserver. Now the question is, why would you use the varnish cache to cache these static files. It makes much more sense to me to only cache the dynamic files so that php-fpm / mysql don't get hit that much. Am I correct or am I missing something here? UPDATE I want to add some info to the question based on the answer given. If you have a dynamic website, where the content actually changes a lot, chaching does not make sense. But if you use WordPress for a static website for example, this can be cached for long periods of time. That said, more important to me is static conent. I have found a link with some test and benchmarks on different cache apps and webserver apps. http://nbonvin.wordpress.com/2011/03/14/apache-vs-nginx-vs-varnish-vs-gwan/ NginX is actually faster in getting your static content, so it makes more sense to just let it pass. NginX works great with static files. -- Apart from that, most of the time static content is not even in the webserver itself. Most of the time this content is stores on a CDN somewhere, maybe AWS S3, something like that. I think the varnish cache is the last place where you want to have you static content stored.

  Read the article

• Old scheduled task still being started, but can't find it.

  - by JvO

  System: Windows XP Home Summary: Some scheduled task is still being started by Windows, but I can't find it, nor determine where its configuration has been stored. This is turning into a mystery for me... I set up a Windows XP Home machine to run a task at 7:00 AM, using the Task manager. This was a clean install, no users defined, so you got straight to the desktop after starting the machine. The filesystem uses NTFS. Later on, I needed to introduce users, so I created one (named Sam) with administrator privileges. After this I noticed that the scheduled task failed, most likely due to privilege errors (i.e. can't write to a network drive). So I want to delete the old task, and add it again with the correct user credentials. However.... I can't find the old task!! I know it is still being executed at 7:00 AM, but there's no mention anywhere on the system of this task. I've looked in c:\windows\tasks for .job files, but there's only the "MP Scheduled Scan.job" from Security Essentials. I've searched the whole disk for mention of the batch file that is being run, but can't find it. So why is this old task still running, and more importantly, why can't I find it? Would it have something to do with introducing users on XP?

  Read the article

• OpenLDAP ACLs are not working

  - by Dr I

  First things first, I'm currently working with an OpenLDAP: slapd 2.4.36 on a Fedora release 19 (Schrödinger’s Cat). I've just install the openldap with yum and my configuration is the following one: ##### OpenLDAP Default configuration ##### # ##### OpenLDAP CORE CONFIGURATION ##### include /etc/openldap/schema/core.schema include /etc/openldap/schema/cosine.schema include /etc/openldap/schema/inetorgperson.schema include /etc/openldap/schema/nis.schema pidfile /var/lib/ldap/slapd.pid loglevel trace ##### Default Schema ##### database mdb directory /var/lib/ldap/ maxsize 1073741824 suffix "dc=domain,dc=tld" rootdn "cn=root,dc=domain,dc=tld" rootpw {SSHA}SECRETP@SSWORD ##### Default ACL ##### access to attrs=userpassword by self write by group.exact="cn=administrators,ou=builtin,ou=groups,dc=domain,dc=tld" write by anonymous auth by * none I launch my OpenLDAP service using: /usr/sbin/slapd -u ldap -h ldapi:/// ldap:/// -f /etc/openldap/slapd.conf As you can see it's a pretty simple ACL which aim to allow access to the userPassword attribute to a specific group read only, then to the owner read and write to anonymous requiring auth and refuse the access to everyone else. The problem is: Even using a valid user with correct password my ldapsearch ends with zero informations retrieved from the directory, plus I've got a strange response on the result line. # search result search: 2 result: 32 No such object # numResponses: 1 here is the ldapsearch request: ldapsearch -H ldap.domain.tld -W -b dc=domain,dc=tld -s sub -D cn=user,ou=service,ou=employees,ou=users,dc=domain,dc=tld I did not specify any filter as I want to check that ldapsearch is correctly printing only allowed attribute.

  Read the article

• Can't Install Win2k8 On KVM - Classic 0x80070013 error

  - by javano

  I am trying to install Win2k8 Std as a KVM guest on Debian Squeeze. As you can see from these screen shots; No drives are detected (I have blanked out a 20GB image for testing) - screenshot1 I am using this driver CD: - screenshot2 I have signed the Win7 driver (I assume this was the most appropriate one?) - screenshot3 I can now see an unpartitioned drive - screenshot4 But I can't create a new partition on here, getting the error code 0x80070013 - screenshot5 I have had this error code before but only on a physical server. If I remember correctly it was complaining because the disks were partitioned as GPT (because it was a server that was being re-purposed) so repartitioning with an MS-DOS table fixed that. This is a blank disk image though. What is wrong here, and how can I correct this? Thank you. UPDATE I have booted the VM with a Gparted-Live disk and formatted this volume with an MS-DOS partitioning scheme, and a single 20GB NTFS file system. Now when I boot the Win2k8 CD, load my drivers, I get a different error. As you can see at the bottom of screenshot6 "Windows cannot be installed on this hard drive space. Windows must be installed to a partition formatted as NTFS". Clicking format produces the error (0x80004005) on the screen, so I think this is still a driver issue because Windows can see the drive but not interact with it properly. Is that insane thinking?

  Read the article

• Apache Bench reports different result with same page

  - by Aspis

  I'm running into a little problem base-lining an Apache2/fcgi/php-fpm server I am setting up. 1) If I run: ab -n 15000 http://mysite.com/index.php. Apache Bench returns Time per request: 41ms but document length: 0 bytes and html transferred: 0 bytes. The Transfer rate: 7.9Kb/s. 2) If I run: ab -n 15000 http://mysite.com/ Apache Bench returns Time per request: 83ms along with the accurate document length and html transferred total. The APC cache status reports identical hit counts from both test. Also Apache Bench reports no errors in either case. Overall, no errors on any test sites and all logs are clean, etc. DocumentRoot is set to index.php so I would expect both of these test runs to produced a similar result. My 2 question(s) are: 1) why the discrepancy? 2) which is the correct result? I've seen plenty of results like test 1 posted (with out question) but frankly from my own experience and those of others, accurate testing is hard to come by. Even with out goofy issues like this.

  Read the article

• Why is crontab giving "No such file or directory" error when the file DOES exist?

  - by fettereddingoskidney

  I am getting the following three lines in an error message in /var/mail/username after the following job runs in crontab... 15 * * * * /Applications/MAMP/htdocs/iconimageryidx/includes/insertPropertyRESI.php Errors: /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 1: ?php: No such file or directory /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 3: syntax error near unexpected token `'initialize.php'' /applications/mamp/htdocs/iconimageryidx/includes/insertpropertyRESI.php: line 3: `require_once('initialize.php'); The PHP script I am trying to execute DOES in fact exist, and I have made absolutely sure the spelling is correct several times. I ran a crontab on another script before and it worked just fine...any ideas?? The 2nd & 3rd Errors are from line 3 in the following script (the one I am trying to run with the crontab): <?php require_once('initialize.php'); require_once('insertPropertyTypes.php'); $sDate; if(isset($_GET['startDate'])) { $sDate = $_GET['startDate']; } else { $sDate = ''; } $insertResi = new InsertPropertyTypes('Listing', $sDate, 'RESI'); ?> When I run my script insertPropertyRESI.php in the browser, it runs just fine???? Also, initialize.php and insertPropertyTypes.php are in the same directory as insertPropertyRESI.php I am using MAMP with PHP 5.3.5 thakns for the help :?

  Read the article

• SendMail not working in CentOs 6.4

  - by Kane

  I am trying to send e-mails from my CentOS 6.4 but it does not work. My knowledge about servers is quite limited, so I hope someone can help me. Here is what I did: First i tried to send an email using the "mail" command, but it was not in the OS so I installed it. # yum install mailx After that, I tried sending an email using the "mail" command, but it did not send anything. I checked it on the internet and I realized I needed an e-mail server like sendmail, so I installed it. # yum install sendmail sendmail-cf sendmail-doc sendmail-devel After that, I configured it following some tutorials. First, sendmail.mc file. # vi /etc/mail/sendmail.mc Commented out the next line: BEFORE # DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl AFTER # dnl DAEMON_OPTIONS('Port=smtp, Name=MTA') dnl Check that the next lines are correct: # FEATURE(`virtusertable', `hash -o /etc/mail/virtusertable.db')dnl # ... # FEATURE(use_cw_file)dnl # ... # FEATURE(`access_db', `hash -T<TMPF> -o /etc/mail/access.db')dnl Update sendmail.cf # m4 /etc/mail/sendmail.mc > /etc/mail/sendmail.cf Open the port 25 adding the proper line in the iptables file # vi /etc/sysconfig/iptables # -A INPUT -m state --state NEW -m tcp --dport 25 -j ACCEPT restart iptables and sendmail # service iptables restart # service sendmail restart So i thought that would be ok, but when i tried: # mail '[email protected]' # Subject: test subject # test content #. I checked the mail log: # vi /var/log/maillog And that is what I found: Aug 14 17:36:24 dev-admin-test sendmail[20682]: r7D8RItS019578: to=<[email protected]>, ctladdr=<[email protected]> (0/0), delay=1+00:09:06, xdelay=00:00:00, mailer=esmtp, pri=2460500, relay=alt4.gmail- smtp-in.l.google.com., dsn=4.0.0, stat=Deferred: Connection timed out with alt4.gmail-smtp-in.l.google.com. I do not understand why there is a connection time out. Am I missing something? Can anyone help me, please? Thank you.

  Read the article

• Failing to load rootfs: Ubuntu 10 + grub2 + rootfs ext4 w/ RAID1

  - by James

  I am having problems booting a new Ubuntu 10 (server) install. My primary HD (/dev/sda) is laid out as follows: Device Boot Start End Blocks Id System /dev/sda1 * 1 18 144553+ 83 Linux <-- /BOOT /dev/sda2 19 182401 1464991447+ 5 Extended /dev/sda5 19 2207 17583111 fd Linux raid autodetect /dev/sda6 2208 11934 78132096 fd Linux raid autodetect <-- / (ROOTFS) /dev/sda7 11935 182401 1369276146 fd Linux raid autodetect The rootfs is part of a RAID1 (software) array (currently degraded): # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md2 : active raid1 sda6[1] 78132032 blocks [2/1] [_U] The UUIDs for the partitions are as follows: # blkid /dev/sda1 /dev/sda1: UUID="b25dd301-41b9-4f4d-9b0a-0e31713dd74c" TYPE="ext2" # blkid /dev/sda6 /dev/sda6: UUID="af7b9ede-fa53-c0c1-74be-31ec752c5cd5" TYPE="linux_raid_member" # blkid /dev/md2 /dev/md2: UUID="a0602d42-6855-482f-870c-6f6ecdcdae3f" TYPE="ext4" Finally, I have my grub2 menuentry setup as follows: ### BEGIN /etc/grub.d/10_linux ### menuentry 'Ubuntu, with Linux 2.6.32-25-server' --class ubuntu --class gnu-linux --class gnu --class os { insmod ext2 insmod raid insmod mdraid set root='(hd0,1)' search --no-floppy --fs-uuid --set b25dd301-41b9-4f4d-9b0a-0e31713dd74c linux /vmlinuz-2.6.32-25-server root=UUID=a0602d42-6855-482f-870c-6f6ecdcdae3f ro nosplash noplymouth initrd /initrd.img-2.6.32-25-server } When I attempt to boot, grub loads OK, however I eventually get the following error message: Gave up waiting for root device. ALERT /dev/disk/by-uuid/a0602d42-6855-482f-870c-6f6ecdcdae3f does not exist. Dropping to a shell! If from the grub bootloader I open a grub command line, I can ls (hd0,) and it lists the correct partitions with the UUIDs as shown above - sda6 shows 'a0602d42-6855-482f-870c-6f6ecdcdae3f' (the RAID UUID). If I ls (md2)/ it properly lists all the files on the RAID1 filesystem (ext4) so it doesn't appear to be an issue accessing the raid device. Does anyone have any suggestions as to what the problem might be? I can't figure this one out.

  Read the article

< Previous Page | 497 498 499 500 501 502 503 504 505 506 507 508  | Next Page >