Search Results

Search found 15875 results on 635 pages for 'border box'.

Page 502/635 | < Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >

• Move an existing RAID 5 array from Ubuntu to Gentoo

  - by Cocoabean

  I have a 64-bit Ubuntu machine with a 4-disk RAID 5 using software raid (md). I've been able to boot an Ubuntu LiveCD and recognize the array with a simple mdadm -A /dev/md0. It was easy to mount after that and nothing had to rebuild. I'm installing Gentoo on this box now (multi-boot, non-RAID root partition) and I have md auto-detect turned on in the kernel. When I boot Gentoo I get: "invalid superblock magic on sdd" for each of the drives in the array. I boot back to Ubuntu and they mount no problem. I tried copying the mdadm.conf that works in Ubuntu to Gentoo, and then ran mdadm -A /dev/md0 but it reports that there is no array named md0. I don't want to lose data (obviously) and I don't want to have to let the RAID rebuild every time I switch between OSes. Any help is appreciated. Both are using mdadm 3.1.4 Both are running 64-bit kernels. mdadm -D /dev/md0 from Ubuntu yields: http://pastebin.com/5gj2QNkV UPDATE: After rebooting I noticed that it still complains about invalid blocks, but cat /proc/mdstat shows an inactive /dev/md127 with the same disks as my raid. I want to mount it but I don't want to get stuck waiting for a rebuild or destroying it inadvertently. mdadm -D /dev/md127 Here is pastebin of mdadm -D /dev/md127 on gentoo: http://pastebin.com/gDCWn0Rn UPDATE II: dmesg output about 'invalid raid superblocks' http://paste.ubuntu.com/885471/ fdisk -l from Ubuntu, /dev/md0 does not have any partitions but I do have it mounted and accessible: http://paste.ubuntu.com/885475/

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• SQL Server Backup problem when browsing to the directory

  - by Richard West

  I want to allow a group (eg. 'BackupManagers') who can only preform backup and restore operations on certain databases. When creating the BackupManagers user account I checked db_backupoperator. When the user logs in to create a backup they get an error message similar to the following when the select Tasks - Backup - Click on Add in the destiantion block - click on the "..." button to browse TITLE: Locate Database Files - MYSERVER\SQL2005 E:\MSSQL\Backup Cannot access the specified path or file on the server. Verify that you have the necessary security privileges and that the path or file exists. If you know that the service account can access a specific file, type in the full path for the file in the File Name control in the Locate dialog box. I have confirmed that the user has permissions to the folder. I have even created a share to this folder and had them access it through explorer. They are able to create and delete files within the folder. I have found that if they type in the path to the file instead of using the "..." button to browse the directory tree then they can create a backup file fine. Why is the browse button not working as expected? Thanks!

  Read the article

• Regular issue with keys on temp tables

  - by Christian

  We run a large forum with lots of reads and writes, particularly to the posts and topics tables which are both innodb. Last week I started doing 12 hourly backups with innobackupex because mysqldump just takes forever (7+ million rows in posts table.) It seems that something doesn't like these backups because I have a recurring problem every other day. The symptoms; The front page of the site starts throwing errors The logs start showing errors like Error: 126 - Incorrect key file for table '/tmp/mysql/#sql_4e87_14.MYI'; try to repair it The /tmp/ dir fills up and we start getting Error: 1030 - Got error 28 from storage engine in the logs. The only way to fix is to optimize table on each of the posts and topics tables. I'm trying all I can to stop MySQL using disks for temp tables, but I'd have more problems than this if it used all my memory also. My my.cnf is here; https://gist.github.com/cbiggins/0aa26f6defb7a14541d7 The box has 32GB memory and I don't come near that usually. Currently at 15GB use. Thanks in advance. Update 1: Despite the conf looking like there is replication, there isn't. This is a stand alone instance.

  Read the article

• How to setup an IPSec / GRE tunnel on Windows Server 2008

  - by qbeuek

  I have a Windows Server 2008 that has a single network interface configured with a public IP address. My business partner has a private network. From my server, I need to access all the devices on his private network, and those devices must be able to access my server. My business partner has a standard solution for these requirements. They will setup an IPSec + GRE tunnel to my server. They told me, that I will need an additional public IP address for this to work. If it really is necessary, there is no problem, I can get an additional public IP address, although it will be assigned to the same physical network interface. I assume that on my server I will have both public IP addresses and also the private IP address from the tunnel (the same that is visible for the devices inside the private network). What alternatives do I have? Is it possible to configure this tunnel on my Windows Server 2008? Can it be done using only Windows tools, or do I need an additional free / commercial VPN software? If it cannot be done directly on Windows, can I setup an additional virtual machine running Linux, that will handle the IPSec + GRE tasks? How to do it? If it cannot be done on a virtual linux box, will I have to buy and setup a Cisco router to handle the IPSec + GRE tasks? Thanks for your opinions. I'm watching this question to clarify any issues or questions.

  Read the article

• Use Mac OS X Server As Development Environment

  - by macinjosh

  I've installed Mac OS X Server 10.6.3 on my laptop to use as my normal OS. I do a lot of web development and thought it would be handy to run OS X Server so I could more easily manage my local development environment (Apache Virtual Hosts, Hostnames for each local site, etc). I'm really enjoying the new setup except for one problem. DNS. My ideal situation would be to add a site (some-site.local) in the Web Service and then go to the DNS Service and add a primary record for the new site. I actually got this working at one point but after a reboot it stopped working! The records look the same as they did before the reboot but the site doesn't come up in Safari. Here is a list of my needs: Need to be able to add new domains at a whim Domains always map to a site on the same box's Web Service Local & External IPs often change It would nice if it worked on any network (i.e. WiFi at the airport or coffee shop) Sites only need to be accessible locally Configuration should stay put even after rebooting I've done some googling and used this as a bit of guide. In the past I've used MAMP and then just a local Apache/PHP/MySQL install with a manually managed hosts file. I'd rather not go back.

  Read the article

• How to set up TightVNC Java viewer index.html on web server?

  - by penyuan

  I've got the Java TightVNC viewer applet set up with the provided index.html on my Mac OS X 10.6.3 with web sharing enabled. Using a remote computer I was able to get to the webpage but I only see a white box with an X (for error?) that represents where the viewer is supposed to be. Any ideas on how to get this to work? I've tried to set the port (in index.html) to 5900 and 5901, none worked. Are any of these the default VNC port for Mac OS X 10.6.3? Also, I've activated Screen Sharing and Remote Login in System Preferences, allowing VNC viewers to connect. Here is the code for my index.html: <HTML> <TITLE> TightVNC desktop </TITLE> <APPLET CODE="classes/VncViewer.class" ARCHIVE="classes/VncViewer.jar" WIDTH="1440" HEIGHT="900"> <PARAM NAME="PORT" VALUE="5900"> <PARAM NAME="Scaling factor" VALUE="50"> </APPLET> <BR> <A href="http://www.tightvnc.com/">TightVNC site</A> </HTML> Again I can get to this page, but the applet doesn't seem to work, the Java console also doesn't say anything. Thanks in advance for your help!

  Read the article

• I/O Error on LG GSA-H12N DVD drive on Windows 7

  - by Ashwin

  I am facing an I/O Error when I try to burn DVD data discs on my LG GSA-H12N DVD drive on Windows 7. Note that I was able to do this same operation on the same hardware/software just a day earlier without any problems, but with Windows XP. The only change (AFAIK) has been the installation of Windows 7 to replace Windows XP on this PC. Here is the error I get when I try to burn a DVD data disc using CDBurnerXP 4.2.7.1801: Burning error occured An error occured while burning the disc. Most likely the disc is not usable. Usually these errors happen if the inserted media is not compatible to the drive or of poor quality. (devNTSPTI_IO_Error) Could not write to Disc (LBA: 52864 Length: 32). SCSI Pass-through Interface I/O Error. - 0xFF045D Note that there can be no problem with the discs since I have been using the same discs (from the same box) just before the Windows 7 installation with no problems. The only change has been Windows 7. I tried InfraRecorder v0.5 and ImgBurn v2.5 and got similar I/O errors: Note that Windows 7 lists the LG GSA-H21N drive as being compatible (see this link). I also checked the LG Drivers website and using the firware update from there updated the drive firmware from version UL01 to UL02. But, even this has not helped. The drive reads DVDs without any problem, but continues to produce coasters. Could someone help me figure out what is the problem? Thanks :)

  Read the article

• Password-protected sharing allows access to users who have no account?

  - by romkyns

  Running Win7 on two computers in my LAN. Computer A has password-protected sharing enabled, and shares a folder. It has a single user account "Bob", and the Guest account is turned off. The network is workgroup-based. According to the descriptions of the "password-protected sharing" I could find, the only people who can access the shared folder via the LAN are those who know the username+password for the "Bob" account. However a second computer on the LAN is able to view this shared folder by simply browsing to Computer A. They don't need to enter any passwords or anything. The only user account registered on that PC is called "Jim", and has a different password from "Bob". How on earth is computer B able to view this shared folder? Is the popular description of the "password-protected sharing" feature inaccurate / did I misunderstand it big time? P.S. There is a possibility that the password for "Bob" has been entered on that PC once, and possibly the "remember password" box was checked. I've looked in the "Credential Manager" on both computers and there is nothing saved anywhere.

  Read the article

• Slow File Copy observed copying 40GB files across network to iSCSI device

  - by Rick

  Here's a curious ones for the gurus: Setup: Source Machine: Windows Server 2003 R2 machine with local hard drive. VHD file of 40GB. 1 x 1Gbps network card, Cat6 cable, switch. Target Machine: Windows Server 2008 R2 machine with iSCSI connection to iSCSI target on separate machine (1TB, RAID5). 1 x 1Gbps network card, Cat6 cable, connected to same switch as for Source Machine. Second 1Gbps network card, Cat6 cable, connected via isolated switch to the iSCSI target. Switches are Netgear JGS524 model (web managed). If I copy from the Win2003R2 machine to Win2008R2 machine local drive I get 40GB in 45 minutes, 36 seconds. If I copy from the Win2008R2 machine to the iSCSI target (local drive to iSCSI target) I get 40GB in 37 minutes 56 seconds. If I copy from the Win2003R2 machine to the iSCSI target via the Win2008R2 machine I get 40GB in 3 hours, 50 minutes, 24 seconds. All copies were done via the following command issued on the Win2008R2 box: XCOPY <source> <target> /J XCOPY /J - Copies using unbuffered I/O. Recommended for very large files. So, what's the bit I'm missing here? Why does a back-to-back copy take in total 1 hour, 23 minutes, 32 seconds when a "straight through" copy take almost 3 times as long? Switches show no errors, network hovers around the 3% utilisation mark for the duration of the copy (whereas the "back-to-back" copies are around the 25% utilisation mark). What have I missed?

  Read the article

• Why do I get a DegradedArray event with mdadm

  - by azera

  Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

  Read the article

• how to automatically mount ~/Private using ecryptfs when logging in via ssh pubkey

  - by andreash

  Raionale: I want to be able to automatically make backups to a remote machine, which will be encrypted with ecryptfs. The title says it all: I set up ecryptfs-utils on my Debian Squeeze box, and set up one user to use it via ecryptfs-setup-private. When I log in via SSH using password authentication, the ~/Private directory automatically gets mounted. How can I achieve that ~/Private also automatically gets mounted when logging in via SSH using public key authentication? Obviously, the best solution would be if ecryptfs could somehow 'use' the SSH public key to en/decrypt the data (I know that then using the user's password would not be able to en/decrypt the data any more; this would be acceptable). Probably, this will not work. So perhaps somehow call ecryptfs-mount-private via ssh before logging in via public key? Probably, then I would need to somehow pipe the passphrase through the SSH connection, right? So I would need to store it on the source machine's file system. Not nice either. Any other ideas?

  Read the article

• Virtualbox - differencing disk based on different differencing disk

  - by Klinki

  I'm trying to create differencing image based on differencing image in VirtualBox 4.2.18. Official documentation says it should be possible: http://www.virtualbox.org/manual/ch05.html#diffimages Basically I want to achieve this drive hierarchy: + immutable image with Debian and all software installed +---- differencing image with specific configuration, autoreset=off, readonly +-------- differencing image with autoreset=on +---- another differencing image for different virtual machine +-------- differencing image with autoreset=on I successfully created differencing image based on differencing image, but I'm not able to connect it to virtual machine :( It always shows error: Failed to open the hard disk .... cannot register hard disk ... because hard disk with UUID ... already exists Here is screenshot of Virtual Media Manager and error dialog Virtual Media Manager Window screenshot Very strange is that the new differencing image (tempdrive.vdi) doesn't have Actual Size 0. I wasn't able to connect it, but still, it has 36KB of data on it... This is very similar to this older question: How to create a chained differencing disk of another differencing disk in Virtual Box? but suggested solution is not working anymore in VirtualBox 4.2.18, so I posted it as a new question. (Limit for posting links and screenshots is quite annoying..)

  Read the article

• Rebuild Apple RAID set

  - by Clinton Blackmore

  We have a Mac Pro tower with an Apple RAID card in it using third party drives. When one drive failed, we replaced it and the RAID 5 set was nearly done rebuilding when the computer was rebooted. It did not come back up. We are now booting up off of a different internal volume, and have three (third-party) drives of identical spec (including revision and firmware) in the box. One of the drives is a global spare; the other two are recognized as belong to a RAID set but are in "Roaming" mode. The intention is to recreate the three-drive RAID set using the data on the two drives that are good. When we tell the system to create a RAID 5 using the three drives, it tells us that it'll create a RAID set but everything will be lost. There are no obvious options to rebuild a RAID using the two good drives and incorporating the third drive in Apple's RAID Utility, and we've looked through the options for the raidutil command. Fortunately, all important data is backed up, and we can rebuild from scratch, but, is there any way to make the RAIDset work again?

  Read the article

• Static noise in headphones

  - by John Murdoch

  I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

  Read the article

• How to send Content-Disposition headers in apache for files?

  - by Rory McCann

  I have a directory of text files that I'm serving out with apache 2. Normally when I (or any user) access the files they see them in their browser. I want to 'force'* the web browser to pop up a 'Save as' dialog box. I know this is possible to do with the Content-Disposition headers (more info). Is there some way to turn that on for each file? Ideally I'd like something like this: <Directory textfiles> AutoAddContentDispositionHeaders On </Directory> And then apache would set the correct content disposition header, including using the same filename. Something like this might be possible with the apache Header directive. Bonus points if it's included by standing in apache in debian. I could do a simple PHP wrapper script that takes in a filename argument, makes the call to header(...) and then prints the file, but then i have to validdate input etc. that's work I'm trying to avoid. * I know you can't actually force things when it comes to the web

  Read the article

• Xvnc4 started from xinetd only displays empty gray X screen

  - by scott8035

  I'm attempting to setup an Ubuntu 10.10 box so that anyone can connect to port 5900 and be greeted by the gdm login manager. To do so, I added a vnc entry in /etc/services and I am starting Xvnc4 using this xinetd config file: service vnc { protocol = tcp socket_type = stream wait = no user = nobody server = /usr/bin/Xvnc server_args = -geometry 1000x700 -depth 24 -broadcast -inetd -once -securitytypes None } This kind of works...I can start multiple sessions all to port 5900, and I get an X screen. The problem is that I only get an empty, gray X screen with no applications started. I know when you run vncserver from the command line it will look to your ~/.vnc/ directory for your passwd and xstartup files, and I think what I want to do is put "gnome-session" into the xstart file. However, which xstartup file? The running user is "nobody" who obviously doesn't have a ~/.vnc/ directory. I tried a /root/.vnc/xstartup file and a ~scott/.vnc/xstartup file and it doesn't look like they were even read. I changed the xinetd vnc service so that it would "strace" Xvnc4. I looked thru all the "open" lines and didn't get a clue as to what file it was trying to read for xstart. Can anyone help? I just want a terminal server where the user is presented with a gdm login screen.

  Read the article

• Name one good reason for immediately failing on a SMTP 4xx code

  - by Avery Payne

  I'm really curious about this. The question (highlighed in bold): Can someone name ONE GOOD REASON to have their email server permanently set up to auto-fail/immediate-fail on 4xx codes? Because frankly, it sounds like "their" setups are broken out-of-the-box. SMTP is not Instant Messaging. Stop treating it like IRC or Jabber or MSN or insert-IM-technology-here. I don't know what possesses people to have the "IMMEDIATE DELIVERY OR FAIL" mentality with SMTP setups, but they need to stop doing that. It just plain breaks things. Every two or three years, I stumble into this. Someone, somewhere, has decided in their infinite wisdom that 4xx codes are immediate failures, and suddenly its OMGWTFBBQ THE INTARNETZ ARE BORKEN, HALP SKY IS FALLING instead of "oh, it'll re-attempt delivery in about 30 minutes". It amazes me how it suddenly becomes "my" problem that a message won't go through, because someone else misconfigured "their" SMTP service. IF there is a legitimate reason for having your server permanently set up in this manner, then the first good answer will get the check. IF there is no good reason (and I suspect there isn't), then the first good-sounding-if-still-logically-flawed answer will get the check.

  Read the article

• Routing for Two Hosts Behind a IPSec Tunnel

  - by Brent

  Network A 10.110.15.0/24 Firewall is .1 Host A is .2 Network B 10.110.16.0/24 Firewall is .1 Host B is .2 Two Cisco ASA's. IPSec tunnel with a crypo map that secures 10.110.15.0/24 <- 10.110.16.0/24. Let's say two hosts, 10.110.15.2 and 10.110.16.2 need to talk to each other. Normally I have to enter a persistent static route on a each host along the lines of: route add 10.110.16.0 mask 255.255.255.0 10.110.15.1 metric 1 -p (on the "A" box) I also have to enter another persistent static route on the .16 host in order for the traffic to know how to get back to the .15 network. Note that the default for each machine IS the firewall, so .1. I have no problem adding persistent routes on Windows/ESX/*nux machines but what about a smart switch in the .16 network that I want to manage from the .15 network. Do I need to run a routing protocol? Do I need to have Reverse Route Injection enabled on both ends of the IPSec tunnel? Should I add a route on the firewall? If so, how do you formulate it? Does it get a metric of 1 and my default route 0.0.0.0 get a metric of 2?

  Read the article

• Server load high, CPU idle. NFS the cause?

  - by Mech Software

  I am running into a scenario where I'm seeing a high server load (sometimes upwards of 20 or 30) and a very low CPU usage (98% idle). I'm wondering if these wait states are coming as part of an NFS filesystem connection. Here is what I see in VMStat procs -----------memory---------- ---swap-- -----io---- --system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 2 1 0 1298784 0 0 0 0 16 5 0 9 1 1 97 2 0 0 1 0 1308016 0 0 0 0 0 0 0 3882 4 3 80 13 0 0 1 0 1307960 0 0 0 0 120 0 0 2960 0 0 88 12 0 0 1 0 1295868 0 0 0 0 4 0 0 4235 1 2 84 13 0 6 0 0 1292740 0 0 0 0 0 0 0 5003 1 1 98 0 0 4 0 0 1300860 0 0 0 0 0 120 0 11194 4 3 93 0 0 4 1 0 1304576 0 0 0 0 240 0 0 11259 4 3 88 6 0 3 1 0 1298952 0 0 0 0 0 0 0 9268 7 5 70 19 0 3 1 0 1303740 0 0 0 0 88 8 0 8088 4 3 81 13 0 5 0 0 1304052 0 0 0 0 0 0 0 6348 4 4 93 0 0 0 0 0 1307952 0 0 0 0 0 0 0 7366 5 4 91 0 0 0 0 0 1307744 0 0 0 0 0 0 0 3201 0 0 100 0 0 4 0 0 1294644 0 0 0 0 0 0 0 5514 1 2 97 0 0 3 0 0 1301272 0 0 0 0 0 0 0 11508 4 3 93 0 0 3 0 0 1307788 0 0 0 0 0 0 0 11822 5 3 92 0 0 From what I can tell when the IO goes up the waits go up. Could NFS be the cause here or should I be worried about something else? This is a VPS box on a fiber channel SAN. I'd think the bottleneck wouldn't be the SAN. Comments?

  Read the article

• Uninstall Perl 5.10 and Install 5.8 on Ubuntu 10.04

  - by user48848

  I was using Ubuntu 8.04 with installed Perl 5.8.8. I had installed Bugzilla 3.4.4 with some custom scripts and it was working fine. I had to upgrade Ubuntu from 8.04 to 10.04 and automatically Perl is also upgraded from Perl 5.8 to 5.10. Now, accessing Bugzilla displays an error message related to Perl module. While trying to run checksetup.pl, I am getting the following error message: root@cvsnew:/var/www/bugzilla-3.4# perl checksetup.pl * This is Bugzilla 3.4.3 on perl 5.10.1 * Running on Linux 2.6.32-24-generic-pae #39-Ubuntu SMP Wed Jul 28 07:39:26 UTC 2010 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.48 perl: symbol lookup error: lib/i486-linux-gnu-thread-multi/auto/Digest/SHA/SHA.so: undefined symbol: Perl_Tstack_sp_ptr Accessing Bugzilla throws : "500 Internal Server Error". I explored this issue and found that this issue has come up because upgrading Ubuntu upgrades Perl 5.8 to 5.10 automatically. It seems like Perl 5.10.1 isn't binary compatible with the previous. Now, I want to uninstall Perl 5.10.1 and Install Perl 5.8.8 on my Ubuntu 10.04 box. I will appreciate if someone has already done that or share the required steps/commands to do it.

  Read the article

• Dual boot windows 8 pro and windows 7 on XPS 8500 Special Edition

  - by Jesse

  I am trying to install a dual boot with windows 7 premium and windows 8 Pro on an XPS 8500 special edition. I created a new primary partition on my C: drive, inserted the windows 8 install disk, and rebooted my computer from DVD. I select custom install and the dialog box saying "Where do you want to install windows at?" pops up but none of my drives are listed. Please help me determine what is going on. I don't understand why none of my drives are showing up on this menu. Not even the original drive. When I go to load driver and click on the partition I created it tells me "No signed device drivers were found. Make sure the installation media contains the correct drivers, and then click OK." resolved above issue by running setup from the source folder on the install disk instead of booting from DVD. Was able to locate my new partition and start install. It completes the first step of "Copying windows files" just fine but then on the next step "Getting files ready for installation" my computer restarts and attempts to load windows 8 but keeps telling me my pc needs to restart. This keeps going on in an infinite boot loop. Please help, this has been a nightmare!

  Read the article

• Some Can reach bidmail.com others can't.

  - by user69426

  On a windows 7 Professional machine in Chrome one of our Estimating assistants can't get to www.bidmail.com, however the other 3 can. On his machine I did nslookup then bidmail.com and it fails to find it. I then went to a machine that could reach bidmail and did nslookup. It can't find it. I was skeptical and thought maybe it was a cached page so I cleared the cache then went back to bidmail.com was able to get to the page, login, lookup a newly posted bid then download the file. Yet I can not look it up through nslookup and I can't ping it www.bidmail.com and I can't trace it. I remoted to our other warehouse which is set up as a workgroup and attempt to nslookup bidmail and that nslookup fail... and on that machine which has never been to bidmail before it was able to connect to the website! I am totally confused if I can't ping it and I can't use nslookup to get there how in the hell is Chrome getting to the page and how do I get this guy back on? Also while typing this I took a new laptop out of the box plugged it in with no updates and can get to bidmail! omg!

  Read the article

• hosts file seems to be ignored

  - by z4y4ts

  I have almost fresh Ubuntu desktop box. OS was installed two weeks ago and updated from karmic repositories. Last week I had no problems with DNS. But this week something had changed. I'm not sure what and when, and not sure whether I changed any configs. So now I have some really weird situation. According to logs name resolving should work normally. /etc/hosts 127.0.0.1 localhost test 127.0.1.1 desktop /etc/host.conf order hosts,bind multi on /etc/resolv.conf # Generated by NetworkManager search search servers obtained via DHCP nameserver 192.168.0.3 /etc/nsswitch.conf passwd: compat group: compat shadow: compat hosts: files mdns4_minimal [NOTFOUND=return] dns mdns4 networks: files protocols: db files services: db files ethers: db files rpc: db files netgroup: nis But if fact it is not. user@test ~ping test PING localhost (127.0.0.1) 56(84) bytes of data. [skip] Pinging is ok. user@test ~host test test.mydomain.com has address xx.xxx.161.201 But pure I suspect that NetworkManager might cause this misbehavior, but don't know where to start to check it. Any thoughts, suggestions?

  Read the article

• HTB.init / tc behind NAT

  - by Ben K.

  I have an Ubuntu 10 box that I'm trying to set up as a bandwidth-shaping router. The machine has one WAN interface, eth0 and two LAN interfaces, eth1 and eth2. NAT is configured using MASQUERADE as described at InternetConnectionSharing. I'm mostly concerned with shaping outbound traffic from the LAN interfaces -- in the end, I'd like to end up with a hard 768Kbps limit per-LAN-interface (rather than a limit on eth0 pooled across all interfaces). I installed HTB.init, and riffing on the examples, tried to set this up on eth1 by putting three files into /etc/sysconfig/htb: /etc/sysconfig/htb/eth1 DEFAULT=30 R2Q=100 /etc/sysconfig/htb/eth1-2.root RATE=768Kbps BURST=15k /etc/sysconfig/htb/eth1-2:30.dfl RATE=768Kbps CEIL=788Kbps BURST=15k LEAF=sfq I can /etc/init.d/htb start and /etc/init.d/htb stats and see information that /seems/ to suggest it's working...but when I try pulling a large file via the WAN interface the shaping clearly isn't in effect. Any suggestions? My guess is it has something to do with where the shaping falls in the NAT chain, but I really have no idea where to begin troubleshooting this. ---- Update: Here's my /etc/init.d/htb list output, it seems to make sense -- the default rate for eth1 is 768Kbps? ### eth0: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth0: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b ### eth0: filtering rules filter parent 1: protocol ip pref 100 u32 filter parent 1: protocol ip pref 100 u32 fh 800: ht divisor 1 filter parent 1: protocol ip pref 100 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:30 match 00000000/00000000 at 12 match 00000000/00000000 at 16 ### eth1: queueing disciplines qdisc htb 1: root refcnt 2 r2q 100 default 30 direct_packets_stat 0 qdisc sfq 30: parent 1:30 limit 127p quantum 1514b perturb 10sec ### eth1: traffic classes class htb 1:2 root rate 768000bit ceil 768000bit burst 1599b cburst 1599b class htb 1:30 parent 1:2 leaf 30: prio 0 rate 6144Kbit ceil 6144Kbit burst 15Kb cburst 1598b

  Read the article

< Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >