Search Results

Search found 19279 results on 772 pages for 'everything'.

Page 502/772 | < Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >

• Clicking a link in IE6 doesn't load page (internal DNS entry on our intranet)

  - by Callum

  I have a very strange problem that is only affecting some versions of IE6. The problem does affect IE 6.0.2900.5512, but does not seem to affect 6.0.3790.3959 Basically I work for a company and we have an intranet. While I'm not an expert on "internal DNS pointers", what I was able to do was create a website (let's say about football), and when an employee who is sitting behind the company firewall types the word "football" in to the web address bar of their web browser, they get redirected to a particular server. I am told this is some kind "internally pointing DNS entry". So, I've set one of these up, and I have a placed a link to it on our company intranet page. However, when the link is clicked in IE6.0.2900.5512, the page goes blank. Clicking "refresh" then loads the correct page (the one specified in the link). Can anyone help me out here. I have tried changing the way URL is formed, everything from //football to http://football/ etc. The link works fine in every other browser and IE7+, but unfoturnatly, IE6 is still the most common browser in use at my organisation.

  Read the article

• Do I have to do anything for file ACLs to work both before and after I reformat a computer?

  - by Zian Choy

  Let's say that I have a computer running Windows Vista with 2 users: Alice and Bob. Alice is the admin and Bob is a normal user. They each have files in their respective My Documents folders and Bob is not allowed to view Alice's files and Alice has to jump through a UAC elevation to view Bob's. If Alice copies all the files on the computer to an external NTFS-formatted hard drive with the following 2 commands: robocopy "E:\Bob's Files" "C:\Users\Bob\My Documents" /MIR robocopy "E:\Alice's Files" "C:\Users\Alice\My Documents" /MIR And then reformats the hard drive, installs a fresh copy of Windows, and creates 2 users named Alice and Bob on the computer, then will everything in the first paragraph be true after Alice copies the files back onto the internal hard drive? Assume that when the files are copied back over, she logs in as Bob and then copies Bob's files and likewise with her own files. Possibly relevant: Alice and Bob also have passwords on their user accounts and they create new passwords after the computer is reformatted. The main post has been tweaked slightly to make the question clearer. Answers that predate April 2011 are referring to an earlier version of this post.

  Read the article

• switchless Infiniband between two servers on RHEL 6.3

  - by exfizik

  I have 2 servers running RHEL 6.3 which have 2 port Infiniband cards >lspci | grep -i infini 07:00.0 InfiniBand: QLogic Corp. IBA7322 QDR InfiniBand HCA (rev 02) I'm interested in connecting them directly to each other bypassing an Infiniband switch (which I don't have). Quick googling showed that at least in some configurations it's possible. I installed all RedHat Infiniband packages with yum groupinstall "Infiniband Support". However, ibv_devinfo shows that both ports in each card are down, which indicates that cables are not connected. But the cable is connected, although the LEDs are off on the cards (not a good sign). Another source of confusion for me is that according to this, RedHat doesn't come with OFED packages and I'm slightly hesitant to install them from source due to the lack of RedHat support for them... So where am I going with this? The questions I have are: is it possible to have a switchless/direct Infiniband connection between two servers the way I described above? If it's possible, do I have to use the OFED packages or can I configure everything with just the packages coming with RHEL. Why are the LEDs off on my servers even though the cable is connected? Any additional input/advice/pointers would be appreciated. P.S. I followed this guide for installation instructions. The Infiniband cards are clearly recognized by my OS and the rdma service is running. Update: I have opensm installed. When I run it it says: OpenSM 3.3.13 Command Line Arguments: Log File: /var/log/opensm.log ------------------------------------------------- OpenSM 3.3.13 Entering DISCOVERING state Using default GUID 0x1175000076e4c8 SM port is down and stays at that point.

  Read the article

• SMB access from XP to Windows 2008 R2

  - by Pablo

  Here's the thing... I have a very slow file copy performance from Windows XP clients to Windows 2008R2 servers. Here are the facts: Windows XP to Windows 2K3: Fast Windows XP to Windows 2K8: Very Slow Windows 7 to Windows (any): Fast Despite the fact that the obvious solution would be to upgrade to Windows 7, well, we have 900 desktops so it's not an option in the short time. I have tried everything: Disabling SMB2.0, disabling security signatures, changing the TCP Window size, disabling the W2K8 auto tuning, upgraded the drivers, etc. We eliminated the network; both the server and the client are connected to the same core switch (no hops, no routers, same VLAN). Upon monitoring the network with a packet capture utility, we see that the SMB packets being exchanged between the W2K8 and the XP machines are very small packets (256 bytes); despite the fact that the MTUs are properly set (1500) and there is no fragmentation whatsoever. In fact, those SMB packets show, on the IP datagram, that the window is 65535 or close. The same trace, made using the same application but instead of using a W2K8 share uses a Windows XP share (and that goes FAST) shows SMB packets of 4096 bytes. I can post the traces if necessary. So, why does XP-W2K8 negotiation arrange for 24-bytes SMB payload, whereas the XP-XP negotiation arranges for 4096 SMB packets? Any ideas? I am running short of those...

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• on debian, lighttpd apache2 using 80 port, lighttpd throws :address already use error

  - by user1960581

  I bought the linode(linode.com) server the other day. I've been trying to run lighttpd and apache2 at the same port, using lighttpd for static files. As linode is only providing ONE ipv4 address, I tried to bind lighttpd on the ipv6 address. That's where I got the same error each and very single time: can't bind to port [ipv6] 80 Address already in use. I tried bind the ipv4 address. Everything worked. Please help me, this is driving me nuts for the last two days. my lighttpd.conf file:(the ipv6 address isn't true) server.modules = ( "mod_access", "mod_alias", "mod_compress", "mod_redirect", # "mod_rewrite", ) server.document-root = "/var/www" server.upload-dirs = ( "/var/cache/lighttpd/uploads" ) server.errorlog = "/var/log/lighttpd/error.log" server.pid-file = "/var/run/lighttpd.pid" server.username = "www-data" server.groupname = "www-data" server.port = 80 server.bind = "2600:3c02::0000" server.use-ipv6 = "enable" #server.pid-file = "/var/run/lighttpd.pid" index-file.names = ( "index.php", "index.html", "index.lighttpd.html" ) url.access-deny = ( "~", ".inc" ) static-file.exclude-extensions = ( ".php", ".pl", ".fcgi" ) compress.cache-dir = "/var/cache/lighttpd/compress/" compress.filetype = ( "application/javascript", "text/css", "text/html", "text/plain" ) # default listening port for IPv6 falls back to the IPv4 port #include_shell "/usr/share/lighttpd/use-ipv6.pl " + server.port include_shell "/usr/share/lighttpd/create-mime.assign.pl" include_shell "/usr/share/lighttpd/include-conf-enabled.pl" ### ipv6 ### $SERVER["socket"] == "[2600:3c02::0000]:80" { # accesslog.filename = "var/log/lighttpd/ipv6/access.log" # server.document-root = "/var/www/" # server.error-handler-404 = "/index.php?error=404" } and the error message: can't bind to port, 2600:3c02::0000 Address already in use.

  Read the article

• How can a CentOS 6 guest running in VirtualBox be configured as a LAMP server that can be accessed from the Windows host?

  - by jtt89

  I was able to conect Centos6 on Virtual Box to Windows (I can ping in both directions) with Host-only Adapter (for connection between the two) and NAT Adapter (to enable Linux on VB to connect to the Internet). I want to set up httpd, mysql and vsftpd servers and in the end easily connect to httpd from Windows based browser and ftp server with a Windows based client as well. I would also want to have access through SSH. I have a general idea of the steps that are involved, but there is also a configuration that I am not sure about at this point. Lets say I follow these steps: yum install httpd yum install php php-pear php-mysql yum install mysql-server mysql_secure_installation yum install vsftpd yum install mod_ssl Technically I have everything installed, but what would be the next steps that I need to take (from the networking point of view, so to speak) to get it all working)? I know I need to configure, at least Apache, and ftp server, but I am not sure how is it gonna work; like where am I gonna be uloading the sites (I know this can vary), how am I gonna know what address to use in a browser if I wanna go to a website x, y, z on that installation etc. This sounds like I need to do some kind of DNS setup and I am kind of stuck at this point. If somebody could give me a general outline of what are the things that need to be done that would be great (I was looking at a lot of websites and I know about etc/sysconfig/network, httpd.config - not too much about it on Apache's site, hostname, hostname -f etc; but it is kind of hard to piece it all together at this point). I am gonna be looking at the books also, but they not always reflect the setup that I have too (VirtualBox). Thank you.

  Read the article

• Starfield Wildcard SSL Certificate Not Trusted in All Browsers

  - by Austen Cameron

  I am at a loss as to what else I might try in order to debug this issue with a Starfield Wildcard SSL Certificate. The problem is that in certain browsers (Safari or the most-updated chrome you can get for OS X 10.5.8 for example) the certificate comes up as untrusted, even on the root domain. My server setup / background info: General LAMP setup - CentOS 6.3 - on a Godaddy VPS Starfield Technologies Wildcard SSL certificate Installed using the instructions from godaddy's support pages ssl.conf lines are basically as follows: SSLCertificateFile /path/to/cert/mysite.com.cert SSLCertificateKeyFile /path/to/cert/mysite.key SSLCertificateChainFile /path/to/cert/sf_bundle.crt Everything seemingly worked fine until the other night when I noticed the problem in OS X, I assume it's more browser version related, but have only been able to replicate it on that particular machine. What I have tried: Updating sf_bundle.crt from godaddy's cert repository and Starfield's repository versions Following This ServerFault answer from Jim Phares - changing the ChainFile line to sf_intermediate.crt from Starfield's repository Using http://www.sslshopper.com/ssl-checker.html on my url It says the domain is correctly listed on the certificate but comes up with an error that reads The certificate is not trusted in all web browsers. You may need to install an Intermediate/chain certificate to link it to a trusted root certificate. What might I try next to remedy the untrusted certificate issue? Let me know if there is any other information needed that might help debugging this issue. Thanks in advance!

  Read the article

• Windows Vista will not boot; the file header checksum does not match the computed checksum

  - by Magnus

  Right out of the blue, my wife's Sony Vaio stopped booting. This, not so fun, error message displays immediately after POST: The system cannot boot. The file is possibly corrupt. The file header checksum does not match the computed checksum The repair option on the Vista DVD says everything is fine and dandy, it couldn't be more happier or more clueless... Any ideas? Update: CHKDSK reports no issues. CHKDSK /r reports no issues. (Heck, both Windows Repair and CHKDSK could just as well tell me that I have won on lottery or that the earth is flat... ) Some have reported that a mem diagnostic could help, but for me the mem diag has just ran through 5 passes. It doesn't seem to help. According to Sony, pressing F10 should bring up the restore menu, but it doesn't, the error pops up straight after Bios POST. It seems that this error is first in line of all options at this point, and is doesn't put a smile on my face. I have attached an external USB drive and copied all user data/documents to it. I feel an OS re-install is around the corner.

  Read the article

• SSH session closing whilst virtualenv session stays open (I think)

  - by ing0

  I've been developing some sites using Flask recently (running on debian within a virtualenv), and when I am testing I can run it on a port, let's say post 5000. So I run the script like so: . env/bin/activate <- go into virtual environment python file.py <- run python script And I will be given this message: Running on http://0.0.0.0:5000/ So this all works great and I can access my site on this port fine. However... my rubbish ISP always does this thing where it resets something around 1am every morning. I have no idea what this is, everything runs like normal but I always get disconnected from any SSH sessions open. This leaves it running and all I can do is call: lsof -i Which will show me the process but if I kill it and then rerun it things get weird. The: Running on http://0.0.0.0:5000 message still shows but I cannot connect to it anymore. I've tried changing the port number and it seems the only thing that works is trying again later on or on another day. Now I'm assuming that something on my server resets inbetween these times and I would like to think it was maybe that virtualenv session timing out, but I cannot find out how to do this manually, does anyone know?

  Read the article

• PHP unable to load dynamic library... but it is loaded. WTF?

  - by Josh

  I have a CentOS 5.4 server with Apache 2.2.3, mod_fastcgi and PHP 5.2.11. Everything is working great, server is a production server and I've had no complaints. When I was looking in PHP's error log to diagnose a problem with a specific page, I saw the following periodically repeated over and over: [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/apc.so' - /usr/lib/php/modules/apc.so: undefined symbol: php_rfc1867_callback in Unknown on line 0 [03-May-2010 19:54:12] PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php/modules/pdo_mysql.so' - /usr/lib/php/modules/pdo_mysql.so: undefined symbol: php_pdo_get_dbh_ce in Unknown on line 0 I am very confused because APC is loaded, I can see it in the output of phpinfo(). And by the look of these error messages nothing should be working at all. Yet sites seem to be running fine. How can I track down the source of this error?

  Read the article

• 500 Internal Server Error after changing .NET Framework Version to 4.0 in IIS7

  - by René

  I just changed my .NET Framework Version of the Application Pools in IIS7 Manager, following these instructions. Now when I try to re-upload my ASP.Net page, it shows me a 500 - Internal server error. I have tried uploading it in .net 2.0(X86, X64, AnyCPU), and 4.0(X86, X64, AnyCPU), and everything gives the same error. This is all the details the error gives me: "There is a problem with the resource you are looking for, and it cannot be displayed." When keeping the .NET version on 2.0 on the server, it works just fine. Also, when uploading "index.htm", it works fine as well, it just shows the HTML page. This is on Windows Server 2008 R2, by the way. EDIT: I have finally found out how to get the error details. Here they are: "Handler "PageHandlerFactory-Integrated" has a bad module "ManagedPipelineHandler" in its module list." "Most likely causes: •Managed handler is used; however, ASP.NET is not installed or is not installed completely. •There is a typographical error in the configuration for the handler module list. Things you can try: •Install ASP.NET if you are using managed handler. •Ensure that the handler module's name is specified correctly. Module names are case-sensitive and use the format modules="StaticFileModule,DefaultDocumentModule,DirectoryListingModule"." I am sure that I have installed ASP.NET completely. Please help me, -René

  Read the article

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• Blocking requests from specific IPs using IIS Rewrite module

  - by Thomas Levesque

  I'm trying to block a range of IP that is sending tons of spam to my blog. I can't use the solution described here because it's a shared hosting and I can't change anything to the server configuration. I only have access to a few options in Remote IIS. I see that the URL Rewrite module has an option to block requests, so I tried to use it. My rule is as follows in web.config: <rule name="BlockSpam" enabled="true" stopProcessing="true"> <match url=".*" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{REMOTE_ADDR}" pattern="10\.0\.146\.23[0-9]" ignoreCase="false" /> </conditions> <action type="CustomResponse" statusCode="403" /> </rule> Unfortunately, if I put it at the end of the rewrite rules, it doesn't seem to block anything... and if I put it at the start of the list, it blocks everything! It looks like the condition isn't taken into account. In the UI, the stopProcessing option is not visible and is true by default. Changing it to false in web.config doesn't seem to have any effect. I'm not sure what to do now... any ideas?

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• NFS4 permission denied when userid does not match (even though idmap is working)

  - by SystemParadox

  I have NFS4 setup with idmapd working correctly. ls -l from the client shows the correct user names, even though the user ids differ between the machines. However, when the user ids do not match, I get 'permission denied' errors trying access files, even though ls -l shows the correct username. When the user ids do happen to match by coincidence, everything works fine. sudo sysctl -w sunrpc.nfsd_debug=1023 gives the following output in the server syslog for the failed file access: nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/3: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 3 #1: 22: status 0 nfsv4 compound op #2/3: 3 (OP_ACCESS) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #2: 3: status 0 nfsv4 compound op #3/3: 9 (OP_GETATTR) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsv4 compound op ffff88003d0f5078 opcnt 3 #3: 9: status 0 nfsv4 compound returned 0 nfsd_dispatch: vers 4 proc 1 nfsv4 compound op #1/7: 22 (OP_PUTFH) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsv4 compound op ffff88003d0f5078 opcnt 7 #1: 22: status 0 nfsv4 compound op #2/7: 32 (OP_SAVEFH) nfsv4 compound op ffff88003d0f5078 opcnt 7 #2: 32: status 0 nfsv4 compound op #3/7: 18 (OP_OPEN) NFSD: nfsd4_open filename dom_file op_stateowner (null) renewing client (clientid 4f96587d/0000000e) nfsd: nfsd_lookup(fh 28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba, dom_file) nfsd: fh_verify(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking nfsd: fh_lock(28: 00070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) locked = 0 nfsd: fh_compose(exp 08:01/22806529 srv/dom_file, ino=22809724) nfsd: fh_verify(36: 01070001 015c0001 00000000 9853d400 2a4892a5 4918a0ba) nfsd: fh_verify - just checking fh_verify: srv/dom_file permission failure, acc=804, error=13 nfsv4 compound op ffff88003d0f5078 opcnt 7 #3: 18: status 13 nfsv4 compound returned 13 Is that useful to anyone? Any hints on to debug this would be greatly appreciated. Server kernel: 2.6.32-40-server (Ubuntu 10.04) Client kernel: 3.2.0-27-generic (Ubuntu 12.04) Same problem with my new server running 3.2.0-27-generic (Ubuntu 12.04). Thanks.

  Read the article

• Bind9 zone files

  - by user42780

  Well for the better part of the last two hours I've tried to figure out what is actually wrong, but I can't seem to find anything obvious to me. What I'm trying to do is setup my DNS for say(per example) domain.com. This should include two NS records, namely ns1.domain.com and ns2.domain.com. With that there should be a mail record, as well as a CNAME record for www. I've been trough roughly 20 how to's in the last two hours, rewrote everything from scratch four times and I still can't seem to find whats wrong. My only suspicion to this might be two things; the error I get from the bind9 daemon when I stop the service, and the named.conf file. The error I get from the bind9 daemon when stopping the service is: * Stopping domain name service... bind9 rndc: connection to remote host closed This may indicate that * the remote server is using an older version of the command protocol, * this host is not authorized to connect, * the clocks are not syncronized, or * the key is invalid. I honestly doesn't know what this means, apart from the key defined in /etc/bind/rndc.key that's not in the named.conf file(yes, I did try to add it to no avail). Here's all the zone files, and configuration files; http://208.77.101.5/bind9/ If anyone could help, it would be greatly appreciated.

  Read the article

• VRF Internet Gateway Multiple External IP's 1 Internal IP to AWS

  - by user223903

  Trying to setup VRF for the first time and its not working for me even though I keep reading everything online. IP's are different to real life. I have an Internet connection which I can ping to my router in the current setup below 195.45.73.22 I have a block of ip addresses 195.45.121.0/27 I want to setup multiple VPN's to AWS so need to have multiple external ip's thus the block of IP addresses. I have setup the 2nd and 3rd IP address but can not ping them from external. Any help would be grateful. Bryan ip source-route ! ip vrf Internet rd 1:1 route-target export 1:1 route-target import 1:1 ip vrf AWSSydney1 rd 2:2 route-target export 2:2 route-target import 2:2 route-target import 1:1 ip vrf AWSSydney2 rd 3:3 route-target export 3:3 route-target import 3:3 route-target import 1:1 ip cef no ip domain lookup no ipv6 cef multilink bundle-name authenticated interface FastEthernet0/0 description Vocus Internet no ip address speed 100 full-duplex interface FastEthernet0/0.1 encapsulation dot1Q 1 native ip address 195.45.73.22 255.255.255.252 interface FastEthernet0/0.2 encapsulation dot1Q 2 ip vrf forwarding AWSSydney1 ip address 195.45.121.1 255.255.255.224 interface FastEthernet0/0.3 encapsulation dot1Q 3 ip vrf forwarding AWSSydney2 ip address 195.45.121.2 255.255.255.224 interface FastEthernet0/1 description LAN_SIDE ip address 10.0.0.5 255.255.255.0 speed 100 full-duplex no mop enabled ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 195.45.73.21 ip route vrf Internet 0.0.0.0 0.0.0.0 195.45.73.21

  Read the article

• Issues with creating USB bootable Mountain Lion

  - by Sidd

  I am trying to set up a triple boot Windows 8, Mountain Lion, and Ubuntu. I am stuck though. I have got Windows 8 on a partition, and I am trying to get Mountain Lion on there at this point. I installed a VMware with a Snow Leopard 10.6.2 image on the Windows 8 platform. I used the disk utility in this program in order to get Mountain Lion on there. This is what i did specifically: I got the installesd.dmg. I 'mounted' that file or whatever you call it, and out came something along the lines of "Install Mountain Lion OS x" (something like that - it was like a submenu under the installesd.dmg in the disk utility). I got my PNY 8 gb Attache Flash Drive and went to the Erase tab of disk utility. I erased it using the Mac OS Extended (Journaled) setting and called it "Mac". I went to the Restore tab, dragged "Mac" into destination, and dragged "Install Mountain Lion OS x" to the source. Everything seemed to go well, but it didn't. When trying to boot from the flash drive (and yes, I set the BIOS correctly), it skipped it, and loaded Windows 8 normally as if nothing was plugged in. When I try looking at the flash drive in windows 8, it comes up as a 200 mb capacity drive labeled "EFI" with nothing in it (remember, it was 8gb in the beginning). I downloaded Plop Boot Manager, but it did not recognize a USB being plugged in. Does anyone know how I could fix this?

  Read the article

• apache pointing to the wrong version of python on ubuntu how do I change?

  - by one

  I am setting up a flask application on and Ubuntu 12.04.3 LTS EC2 instance and everything seemed to be working well (i.e. I could get to the webpage via the publicly available url) until I tried to import a module (e.g. numpy) and realised the apache python differs from the one I used to compile the mod_wsgi and also the one I am using I am running apache2. The apache2 logs show the warnings (specifically the last line shows the path hasnt changed): [warn] mod_wsgi: Compiled for Python/2.7.5. [warn] mod_wsgi: Runtime using Python/2.7.3. [warn] mod_wsgi: Python module path '/usr/lib/python2.7/:/usr/lib/python2.7/plat-linux2:/usr/lib/python2.7/lib-tk:/usr/lib$ I have tried to set the path in my virtual host conf (my python is located in /home/ubuntu/anaconda/bin along with all of the other libraries): WSGIPythonHome /home/ubuntu/anaconda WSGIPythonPath /home/ubuntu/anaconda <VirtualHost *:80> ServerName xx-xx-xxx-xxx-xxx.compute-1.amazonaws.com ServerAdmin [email protected] WSGIScriptAlias / /var/www/microblog/microblog.wsgi <Directory /var/www/microblog/app/> Order allow,deny Allow from all </Directory> Alias /static /var/www/microblog/app/static <Directory /var/www/FlaskApp/FlaskApp/static/> Order allow,deny Allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> But I still get the warnings and the apache python path hasnt changed - where do I need to put the relevant directives to point apache at my python version and modules (e.g. scipy, numpy etc)? Separately, could I have avoided this using virtual environments? Thanks in advance.

  Read the article

• Cisco "copy startup-config tftp" results in a 0 byte file on the server?

  - by Geoffrey

  I'm pulling my hair out figuring this out. My startup-config is good, I can view it with a show command. I'm trying to copy it to a tftp server: asa5505# copy startup-config tftp Address or name of remote host []? ipaddress Destination filename [startup-config]? t !! %Error writing tftp://ipaddress/t (Timed out attempting to connect) On my TFTP server (SolarWinds), I get the following: binary, PUT. Started file name: C:\TFTP-Root\t binary, PUT. File Exists, C:\TFTP-Root\t binary, PUT. Deleting Existing File. binary, PUT. Interrupted by client, cause: The process cannot access the file 'C:\TFTP-Root\t' because it is being used by another process I've used tftpd32 with same results. I've tried different servers, even one on the same network as the asa ... same results. It'll create a 0 byte file and never do the dump. What's going on? Everything is working normally except for this.

  Read the article

• Managing Many External Hosts Using EC2 and Route 53

  - by futureal

  Looking for a "best practice" answer to managing externally-addressable hosts using the combination of Amazon EC2 and Amazon Route 53, without using Elastic IPs for each host. In my scenario I will have 30+ hosts that need to be accessible from outside EC2, so directly using internal DNS will not work. In the past, I have addressed hosts by assigning an elastic IP to that host (let's say, 55.55.55.55) and then creating an associated A record. For example, let's say I want to create "ec2-corp01.mydomain.com" I might do: ec2-corp01.mydomain.com. A 55.55.55.55 300 Then on that EC2 instance, I would assign the Elastic IP of 55.55.55.55, and everything works fine. Of course, to make this work, I need to have one Elastic IP per instance, which is something I'd like to avoid if possible; I'd like the infrastructure to be more dynamic. So my thought is to try something like: Create a script that queries the internal EC2 tools to determine an instance's private hostname On instance boot, call that script to determine its hostname, and then using the command-line Route 53 interface to find and update that hostname to its current internal hostname Since the host will have a relatively low TTL (let's say 300 as above, or 5 minutes) it should take effect pretty quickly Is this a good idea? Is there a better or more widely accepted way to handle it? If it IS a good idea, what type of record should I be creating? A CNAME that points to the internal host, like ec2-55-55-55-55.compute-1.amazonaws.com? Is an A record better or worse? Thanks!

  Read the article

• What's hogging my CPU?

  - by endolith

  Ubuntu's System Monitor applet shows 100% CPU usage continuously. If I click it, the resources tab shows it at 100% continuously, too. If I go to processes, though, to find out which process is the culprit, there is nothing above 10%. If I run top there is nothing above 10%. I try killing lots of things, but it continues at 100%. How can I find out what's hogging the CPU? This is an unusual situation on a computer I use daily, that normally only hits 100% CPU when I'm doing something that requires it (like loading 32 Firefox tabs) after which it goes back to a normal idle level. It's not a new install or anything. It shouldn't be maxed out. I'm not sure when it started or if I changed something that caused it to happen. Normally I would use top or System Monitor and find the process that had gone out of control, but I can't find anything with those tools this time. It persists after reboots and everything. And the processor is obviously hot, so it's not an erroneous reading. Update: I tried killing any process I saw active again, and killing vino-server finally fixed the problem, even though it never went above 5%. I had enabled Remote Desktop a few days ago (and have obviously now disabled it). How did it manage to use 100% CPU while top only showed it as 5% or so? How do I identify the culprit in the future? Looks like I'm not the only one: Still a problem in both jaunty & karmic. Interestingly, both System Monitor & htop do not show the sum of individual processes being anywhere near 100% cpu.

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Installing MySQL on Ubuntu Natty with Shell Script

  - by Obi Hill

  I'm trying to install MySQL on Ubuntu Natty from a shell script. However, I keep running into one major issue: when I try to define the password outside of the shell script. Below is the code to my shell script (which I have saved in /etc/init.d/install_mysql: export DEBIAN_FRONTEND=noninteractive echo mysql-server-5.1 mysql-server/root_password password $dbpass | debconf-set-selections echo mysql-server-5.1 mysql-server/root_password_again password $dbpass | debconf-set-selections apt-get -y install mysql-server So what I enter in the terminal is: dbpass="mysqlpass" chmod +x /etc/init.d/install_mysql /etc/init.d/install_mysql MySQL installs, but it installs without a password, so I can just do something like mysql -uroot to access mysql (which I don't want). The funny thing is if I put the password in the shell script as regular text, it works ok. So if I my install script is as follows, everything works (i.e. I must specify a password to access mysql): export DEBIAN_FRONTEND=noninteractive echo mysql-server-5.1 mysql-server/root_password password mysqlpass | debconf-set-selections echo mysql-server-5.1 mysql-server/root_password_again password mysqlpass | debconf-set-selections apt-get -y install mysql-server Is there a way I can use a shell script variable to define my password in the shell script, instead of entering the password literally?! Thanks in advance. EDIT I've found the answer to this. The following is what I should have entered in the terminal: dbpass="mysqlpass" export dbpass chmod +x /etc/init.d/install_mysql /etc/init.d/install_mysql It works like a charm now.

  Read the article

< Previous Page | 498 499 500 501 502 503 504 505 506 507 508 509  | Next Page >