Search Results

Search found 49518 results on 1981 pages for 'configuration files'.

Page 504/1981 | < Previous Page | 500 501 502 503 504 505 506 507 508 509 510 511  | Next Page >

• Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

  - by Maalobs

  I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

  Read the article

• No network upsets gnome

  - by Darren Cook

  An issue that has been bothering me for over a year now. My notebook, running ubuntu 10.04, is almost all the time using a wired connection, with static IP address. And a remote DNS server. Network is configured with entries in /etc/network/interfaces and /etc/resolv.conf, rather than whatever the gnome UI tool was (*) But if I'm out, or simply unplug the network cable, a few things get weird. Specifically the gnome-panel stops working - it is still there, but isn't updating. And opening a nautilus window (e.g. to look at files on the local disk) has huge time-outs. By that I mean it will not open the window for something like 30 or 60 seconds; but when it does finally open it I can see the files and it is perfectly usable. Everything else works fine, alt-tab between windows, etc. I use the commandline to find the pid of gnome-panel, kill it, wait a couple of seconds, and it opens up a fresh panel which is normally usable. (Something like 10 minutes later it will have locked/crashed again; the same for the nautilus windows.) I'm guessing this is a DNS issue? Would setting up a local DNS server help? Guess number 2 was related to having a file server mount (samba, though running on another linux box), and symbolic links to files and directories on that file server on my desktop. My question is a bit vague... Does anyone recognize these symptoms, and have a suggestion? Or do you have some troubleshooting suggestions for narrowing down the problem? My /etc/hosts: 127.0.0.1 localhost 127.0.1.1 myhost # The following lines are desirable for IPv6 capable hosts ::1 localhost ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters ff02::3 ip6-allhosts 127.0.0.1 testsite.local #Other test website URLs here UPDATE: Some timings to open some desktop folder icons. This is after pulling out the network cable. A sub-directory of the desktop took 23 secs to open up. Content appears immediately (just 8 files, it has no further subdirectories). The home directory icon took 12 seconds to open up, but then took about 30 seconds for the files to appear. I closed it and tried again. This time it took 18 seconds to open up, but then 70 seconds before anything appeared. *: I couldn't work out how to use the gnome network tool for my needs, which include 3-4 static IPs for testing virtual hosts locally.

  Read the article

• How to overcome Local Group Policy Editor's 1023 character limit?

  - by Louis

  I want to reorder the SSL Cipher Suite Order applied as part of KB2919355, prioritizing the forward secrecy suites above all else. Trying to do this with gpedit at Computer Configuration Administrative Templates Network SSL Configuration Settings SSL Cipher Suite Order is a problem because the new list goes over the tool's character limit. Is there anyway to overcome this limit so I don't have to keep the current priority or omit something from the list?

  Read the article

• Monitoring slow nginx/unicorn requests

  - by injekt

  I'm currently using Nginx to proxy requests to a Unicorn server running a Sinatra application. The application only has a couple of routes defined, those of which make fairly simple (non costly) queries to a PostgreSQL database, and finally return data in JSON format, these services are being monitored by God. I'm currently experiencing extremely slow response times from this application server. I have another two Unicorn servers being proxied via Nginx, and these are responding perfectly fine, so I think I can rule out any wrong doing from Nginx. Here is my God configuration: # God configuration APP_ROOT = File.expand_path '../', File.dirname(__FILE__) God.watch do |w| w.name = "app_name" w.interval = 30.seconds # default w.start = "cd #{APP_ROOT} && unicorn -c #{APP_ROOT}/config/unicorn.rb -D" # -QUIT = graceful shutdown, waits for workers to finish their current request before finishing w.stop = "kill -QUIT `cat #{APP_ROOT}/tmp/unicorn.pid`" w.restart = "kill -USR2 `cat #{APP_ROOT}/tmp/unicorn.pid`" w.start_grace = 10.seconds w.restart_grace = 10.seconds w.pid_file = "#{APP_ROOT}/tmp/unicorn.pid" # User under which to run the process w.uid = 'web' w.gid = 'web' # Cleanup the pid file (this is needed for processes running as a daemon) w.behavior(:clean_pid_file) # Conditions under which to start the process w.start_if do |start| start.condition(:process_running) do |c| c.interval = 5.seconds c.running = false end end # Conditions under which to restart the process w.restart_if do |restart| restart.condition(:memory_usage) do |c| c.above = 150.megabytes c.times = [3, 5] # 3 out of 5 intervals end restart.condition(:cpu_usage) do |c| c.above = 50.percent c.times = 5 end end w.lifecycle do |on| on.condition(:flapping) do |c| c.to_state = [:start, :restart] c.times = 5 c.within = 5.minute c.transition = :unmonitored c.retry_in = 10.minutes c.retry_times = 5 c.retry_within = 2.hours end end end Here is my Unicorn configuration: # Unicorn configuration file APP_ROOT = File.expand_path '../', File.dirname(__FILE__) worker_processes 8 preload_app true pid "#{APP_ROOT}/tmp/unicorn.pid" listen 8001 stderr_path "#{APP_ROOT}/log/unicorn.stderr.log" stdout_path "#{APP_ROOT}/log/unicorn.stdout.log" before_fork do |server, worker| old_pid = "#{APP_ROOT}/tmp/unicorn.pid.oldbin" if File.exists?(old_pid) && server.pid != old_pid begin Process.kill("QUIT", File.read(old_pid).to_i) rescue Errno::ENOENT, Errno::ESRCH # someone else did our job for us end end end I have checked God status logs but it appears CPU and Memory Usage are never out of bounds. I also have something to kill high memory workers, which can be found on the GitHub blog page here. When running a tail -f on the Unicorn logs I see some requests, but they're far and few between, when I was at around 60-100 a second before this trouble seemed to have arrived. This log also shows workers being reaped and started as expected. So my question is, how would I go about debugging this? What are the next steps I should be taking? I'm extremely baffled that the server will sometimes respond quickly, but at others time it's very slow, for long periods of time (which may or may not be peak traffic times). Any advice is much appreciated.

  Read the article

• Ububtu server 12.04 auto installation freezes at kickseeding running if ks.cfg has post scripts

  - by john206

  I'm trying to make a custom Ubuntu Server iso file. Kickstart file (ks.cfg) runs smooth when there is no %post in the file and Ubuntu installs correctly with ks configuration. Installation finishes installing base, apt, grub and It echos: Kickseed Running... and it freezes @ 0% I thought may be apt-get update doesnt work in ks file, I tried to install other apps like apache2 but no luck I have created dozen iso images and installed them in Virtual Box.I have been googling for 3 days and checked out ubuntu forums but haven't figured out the issue. I appreciate your help. This is how I made the iso image. My ks.file and txt.cfg files located in isolinux directory: root@ubuntu:/home/work mount -o loop ubuntu-12.04-amd64.iso original-iso/ rsync -a original-iso/ custom-iso/ cp ks.cfg custom-iso/isolinux/ cp txt.cfg custom-iso/isolinux/ chmod -R 777 custom-iso/ #Creating Iso image mkisofs -D -r -V “$IMAGE_NAME” -cache-inodes -J -l -b isolinux/isolinux.bin -c isolinux/boot.cat -no-emul-boot -boot-load-size 4 -boot-info-table -o ~/ubuntu-12.04-alternate-custom-amd64.iso custom-iso/ ks.cfg #Generated by Kickstart Configurator #platform=AMD64 or Intel EM64T #System language lang en_US #Language modules to install langsupport en_US #System keyboard keyboard us #System mouse mouse #System timezone timezone America/Los_Angeles #Root password rootpw --iscrypted somethingsomething #Initial user user ubuntu --fullname "ubuntu" --iscrypted --password somethingsomething. #Reboot after installation reboot #Use text mode install text #Install OS instead of upgrade install #Use CDROM installation media cdrom #System bootloader configuration bootloader --location=mbr #Clear the Master Boot Record zerombr yes #Partition clearing information clearpart --all --initlabel #Disk partitioning information part /boot --size 128 --fstype=ext3 --asprimary part / --size 512 --fstype=ext3 --asprimary part swap --size 512 part /tmp --size 512 --fstype=ext3 part /var --size 512 --fstype=ext3 part /usr --size 4096 --fstype=ext3 part /home --size 2048 --fstype=ext3 #System authorization infomation auth --useshadow --enablemd5 #Network information network --bootproto=dhcp --device=eth0 #Firewall configuration firewall --disabled --http --ftp --ssh #X Window System configuration information xconfig --depth=32 --resolution=1024x768 --defaultdesktop=GNOME %post apt-get update mkdir /home/user txt.cfg default autoinstall label autoinstall menu label ^Install Custom Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed initrd=/install/initrd.gz quiet ks=cdrom:/isolinux/ks.cfg -- label install menu label ^Install Ubuntu Server kernel /install/vmlinuz append file=/cdrom/preseed/ubuntu-server.seed vga=788 initrd=/install/initrd.gz quiet -- label cloud menu label ^Multiple server install with MAAS kernel /install/vmlinuz append modules=maas-enlist-udeb vga=788 initrd=/install/initrd.gz quiet -- label check menu label ^Check disc for defects kernel /install/vmlinuz append MENU=/bin/cdrom-checker-menu vga=788 initrd=/install/initrd.gz quiet -- label memtest menu label Test ^memory kernel /install/mt86plus label hd menu label ^Boot from first hard disk localboot 0x80

  Read the article

• W2k8, Sybase Driver, Permissions

  - by Clustermagnet

  Trying to get a .net (32bit) app running on a Windows 2008 server. My experience in the Windows world is quite limited. Is this related to the Full/Medium trust settings? Have been Googling for quite some time. Appreciate your feedback! Seeing the following error: Required permissions cannot be acquired. Description: An unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code. Exception Details: System.Security.Policy.PolicyException: Required permissions cannot be acquired. Source Error: An unhandled exception was generated during the execution of the current web request. Information regarding the origin and location of the exception can be identified using the exception stack trace below. Stack Trace: [PolicyException: Required permissions cannot be acquired.] System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Boolean checkExecutionPermission) +7606467 System.Security.SecurityManager.ResolvePolicy(Evidence evidence, PermissionSet reqdPset, PermissionSet optPset, PermissionSet denyPset, PermissionSet& denied, Int32& securitySpecialFlags, Boolean checkExecutionPermission) +57 [FileLoadException: Could not load file or assembly 'Sybase.Data.AseClient, Version=1.155.1000.0, Culture=neutral, PublicKeyToken=26e0f1529304f4a7' or one of its dependencies. Failed to grant minimum permission requests. (Exception from HRESULT: 0x80131417)] System.Reflection.Assembly._nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) +0 System.Reflection.Assembly.nLoad(AssemblyName fileName, String codeBase, Evidence assemblySecurity, Assembly locationHint, StackCrawlMark& stackMark, Boolean throwOnFileNotFound, Boolean forIntrospection) +43 System.Reflection.Assembly.InternalLoad(AssemblyName assemblyRef, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) +127 System.Reflection.Assembly.InternalLoad(String assemblyString, Evidence assemblySecurity, StackCrawlMark& stackMark, Boolean forIntrospection) +142 System.Reflection.Assembly.Load(String assemblyString) +28 System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +46 [ConfigurationErrorsException: Could not load file or assembly 'Sybase.Data.AseClient, Version=1.155.1000.0, Culture=neutral, PublicKeyToken=26e0f1529304f4a7' or one of its dependencies. Failed to grant minimum permission requests. (Exception from HRESULT: 0x80131417)] System.Web.Configuration.CompilationSection.LoadAssemblyHelper(String assemblyName, Boolean starDirective) +613 System.Web.Configuration.CompilationSection.LoadAllAssembliesFromAppDomainBinDirectory() +203 System.Web.Configuration.CompilationSection.LoadAssembly(AssemblyInfo ai) +105 System.Web.Compilation.BuildManager.GetReferencedAssemblies(CompilationSection compConfig) +178 System.Web.Compilation.WebDirectoryBatchCompiler..ctor(VirtualDirectory vdir) +163 System.Web.Compilation.BuildManager.BatchCompileWebDirectoryInternal(VirtualDirectory vdir, Boolean ignoreErrors) +53 System.Web.Compilation.BuildManager.BatchCompileWebDirectory(VirtualDirectory vdir, VirtualPath virtualDir, Boolean ignoreErrors) +175 System.Web.Compilation.BuildManager.CompileWebFile(VirtualPath virtualPath) +86 System.Web.Compilation.BuildManager.GetVPathBuildResultInternal(VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +261 System.Web.Compilation.BuildManager.GetVPathBuildResultWithNoAssert(HttpContext context, VirtualPath virtualPath, Boolean noBuild, Boolean allowCrossApp, Boolean allowBuildInPrecompile) +101 System.Web.Compilation.BuildManager.GetVirtualPathObjectFactory(VirtualPath virtualPath, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +126 System.Web.Compilation.BuildManager.CreateInstanceFromVirtualPath(VirtualPath virtualPath, Type requiredBaseType, HttpContext context, Boolean allowCrossApp, Boolean noAssert) +62 System.Web.UI.PageHandlerFactory.GetHandlerHelper(HttpContext context, String requestType, VirtualPath virtualPath, String physicalPath) +33 System.Web.UI.PageHandlerFactory.GetHandler(HttpContext context, String requestType, String virtualPath, String path) +37 System.Web.MaterializeHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute() +307 System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously) +155 Version Information: Microsoft .NET Framework Version:2.0.50727.4959; ASP.NET Version:2.0.50727.4955

  Read the article

• TrueCrypt drive letter not available

  - by Tono Nam

  With c# or a batch file I mount a trueCrypt volume located at A:\volumeTrueCrypt.tc With c# I do: static void Main(string[] args) { var p = Process.Start( fileName:@"C:\Program Files\TrueCrypt\TrueCrypt.exe", arguments:@"/v a:\volumetruecrypt.tc /lw /a /p truecrypt" ); p.WaitForExit(); } the alternative is to run the command on the command line as: C:\Windows\system32>"C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lw /a /p truecrypt Either way I get the error: Why do I get that error? I was able to run that command the first time. The moment I dismounted the volume and tryied to mount it again I got that error. I know that drive letter W is available because it shows as an available letter on true crypt if I where to open it manually: If I where then click on the button mount and then type the password truecrypt (truecrypt is the password) then it will successfully mount on drive w. Why I am not able to mount it from the command line!? If I change the drive letter on the command line it works. I want to use the drive W though. In other words executing "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /lz /a /p truecrypt will successfully mount that volume on drive z but I do not want to mount it on drive z I want to mount it on drive w. The first time I ran the batch it ran fine. Also if I restart my computer I believe it should work. More info on how to use trueCrypt through the command line can be found at: http://www.truecrypt.org/docs/?s=command-line-usage Edit I was also investivating when does this error occures. In order to generate this error you need to follow this steps. 1) execute the command: (note the /q argument at the end for quiet) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt /q "C...TrueCrypt.exe" = location where trueCrypt is located /v "path" = location where volume is located /n = drive letter n /p truecrypt = password is "trueCrypt" /q = execute in quiet mode. do not show window note I am mounting to drive letter n 2) now volume should be mounted. 3) Open trueCrypt and manually dismount that volume (without using command line) 4) Attempt to run the same command line (without the /q so you see the error) "C:\Program Files\TrueCrypt\TrueCrypt.exe" /v "a:\volumetruecrypt.tc" /ln /a /p truecrypt 5) an error should show up So the problem ocures when I manually dismount the volume. If I dismount it from the command line I get no errors. But I think this is a bug from trueCrypt

  Read the article

• All the Gear and No Idea: Suggestions for re-designing my home/office/entertainment network

  - by 5arx

  Help/ Advice/ Suggestions please: I have a load of kit that I love but which currently operate in disconnected, sometimes counter-productive way. Because I never really had a masterplan I just added these things one after another and connected them up in ad hoc ways. Since I bought my Macbook I've found I spend much less time on the MacPro that was until then my main machine. Perversely, as my job involves writing .Net software, I spend a lot of Mac time actually inside a Windows 7 VM. I stream media from the HP box to the PS3 and thus to the TV, but its not without its limitations/annoyances. We listen to each other's iTunes libraries but the music files are all over the place and it would be good to know they were all safely in one location (and fully backed up). I need to come up with a strategy that will allow me to use all the kit for work, play (recording live music, making tunes, iMovie work), pushing/streaming media to the TV and sharing files with my other half (she uses a Windows laptop and her iPod touch). Ideally I'd like to be able to work on any of the machines and have a shared homedrive that was visible to all machines so all my current files were synced up wherever i was. It would be great if I could access everything securely and quickly over the web. I'd also like to be able to set up a background backup process. The kit list thus far: Apple MacPro 8GB/3x250GB RAID0 + 1TB Apple MacBook Pro 13" 8GB/250GB - I spend a lot of my work time on a Windows 7 VM on this. Crappy Acer laptop (for children's use - iPlayer, watching movies/tv files) HP Proliant Server 4GB/80GB+160GB+300GB Sun Ultra 10 2 x 80GB (old, but in top-notch condition) PS3 160GB iPod Classic 2 x 8GB iPod Touch Observations: Part of the problem is our dual use of Windows and OS X - we can't go for a pure NT style roaming profile. Because the server is also used for hosting test/beta applications and a SQL Server db, it can't be dedicated to file serving. The two Macs really could do with sharing a roaming profile or similar. I'd love to be able to do something useful with the Ultra 10. My other half has been trying to throw it away for over five years now and regularly ask what function it serves in my study :-( I've got no shortage of 500GB external USB hard drives iMovie files are very large and ideally would be processed on a RAID system. Apple's TimeMachine isn't so great. If anyone could suggest all or part of a setup that would fulfil some of my requirements I'd be very grateful. I am willing to consider purchasing one or two more bits of kit (an Apple TV and a Squeezebox have been moted by friends) if they will help make efficiencies rather than add to the chaos and confusion. Thanks for looking.

  Read the article

• How to achieve zero down time

  - by Hiral Lakdavala

  For an application we want to achieve zero database and application down time using Active Active configuration. Our dB is Oracle Following are my questions: How can we achieve active active configuration in Oracle? Will introducing Cassandra/HBase(or any other No SQL dbs) cloud help in zero downtime or it is only for fast retrieval of data in a large db? Any other options? Thanks and Regards, Hiral

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated. Update (2011-06-26) After failing to solve the problem, I resorted to paid Microsoft support. They were unable to solve the problem. Since then I have implemented a solution based on Linux that is working quite well. I will attempt to evaluate any proposed answers as best I can, but current configurations and time constraints will make this slow...

  Read the article

• can not connect through SCP, but SSH connections works

  - by Joe Cabezas

  i am trying to connect to my server to transfer file using scp: $ scp -v -r -P <port> <user>@<host>:~/dir/ dir/ this is the output: OpenSSH_5.2p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /Users/joe/.ssh/config debug1: Reading configuration data /etc/ssh_config debug1: Connecting to <host> [<host>] port <port>. debug1: Connection established. debug1: identity file /Users/joe/.ssh/identity type -1 debug1: identity file /Users/joe/.ssh/id_rsa type -1 debug1: identity file /Users/joe/.ssh/id_dsa type -1 ssh_exchange_identification: Connection closed by remote host but connecting via SSH works fine: $ ssh <user>@<host> -p <port> <user>@<host>'s password: <user>@<host>:~$ OK what can be wrong with this? my /etc/ssh/sshd_config file on the host is: # Package generated configuration file # See the sshd_config(5) manpage for details # What ports, IPs and protocols we listen for Port <port> # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key HostKey /etc/ssh/ssh_host_ecdsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel INFO # Authentication: LoginGraceTime 120 PermitRootLogin yes StrictModes yes RSAAuthentication yes PubkeyAuthentication no #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords #PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding yes X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. UsePAM yes

  Read the article

• Can an administration extraction of an MSI file perform registry and/or system wide changes?

  - by Wil

  I am always getting MSI (or setup EXEs which are basically MSI) files, and half the time they really do not need to be a setup. Microsoft is probably one of the biggest sources - almost every time I want to download a little source code sample, it has a MSI which if you install, only usually has three files. I would rather not do an install and add it to the add/remove programs and who knows what else (although I am sure it wouldn't be that bad) for the sake of three files! For this reason, I always use the following command: MSIEXEC /a <filename.msi> /qb TARGETDIR=<directory name> Now, this works fine and I have never had problems... However, I was just browsing some articles on Technet and found the following resource about administration installs. Apparently, MSI files can have two sequences: The AdminUISequence Table and the AdminExecuteSequence Table. I am not so worried about the AdminUISequence Table as it states that "The installer skips the actions in this table if the user interface level is set to basic UI or no UI", and this is what the /qb switch I use does. However, there is nothing similar written against AdminExecuteSequence Table. I realise that many people who write MSI files simply do it for a single end user and probably do not even touch the admin install options, however, is it possible for them to set items that can affect the system and if so, is there a fail proof way of extracting? I do already use 7-zip, however despite it being on the "supported" page, MSI support is lacking... well... completely sucks. It looses the file names and is generally useless. They have a bug which was closed with no reason/resolution over three years ago, and I opened a forum post and haven't had a reply. I would not really want to install any additional programs if I could help it and just want peoples opinions on this. Thanks. edit - Should also say, I run with UAC on, and I have never ever had a elevation prompt whilst performing the MSIEXEC operation, so I am guessing I have never had a system wide change, however, I am still curious as to if it is possible... As if changes (even just to the user) are possible I would do this locally/in a VM and never on a server or place of importance!

  Read the article

• How to configure apache and mod_proxy_ajp in order to forward ssl client certificate

  - by giovanni.cuccu

  I've developed a java application that need a ssl client certificate and in the staging environment with apache 2.2 and mod_jk it is working fine. In production the configuration is not using mod_jk but mod_proxy_ajp. I'm looking for an apache configuration example that configure ssl and mod_proxy_ajp for sending the ssl client certificate to the java application server (which listens with the ajp protocol). Thanks a lot

  Read the article

• Add DNS record for subdomain on different web hotel

  - by Martin Wiboe

  Hi, I am quite inexperienced with DNS, so this might be simple. Our main domain foo.com is hosted at provider A. Now, we would like to host bar.foo.com at some other provider B - they have the domain set up with them, so I figure that I can do this by somehow adding the nameserver at provider B to the DNS configuration at provider A. The current DNS config is as follows: http://imgur.com/kG099.png How can I add the new subdomain to this configuration? Regards, Martin Wiboe

  Read the article

• In search of a network file system with extended caching to speed up file access

  - by Brecht Machiels

  I'm running a small home server that stores my documents. The disks in this server are in a RAID 1 configuration (using Linux md) and it's also periodically being backup up to an external hard drive to make sure I don't lose them. However, I'm always accessing the files from other computers on the home network using an SMB share, and this results in a considerable speed penalty (especially when connected over WLAN). This is quite annoying when editing large files, such as digital camera RAWs, for example. I've been looking for a solution to this problem. It would have to offer some kind of local caching to speed up the file access. The client would preferably not keep a copy of all data on the server, as it consists of a very large collection of photographs, most of which I will not access frequently. Instead, it should only cache the accessed files and sync the changes back in the background. Ideally, it would also do some smart read-ahead (cache the files that are in the same directory as the currently opened file, for examples), but I suppose that's asking a bit much. Synchronization should be automatic (on file change). Conflicting file changes (at the same time on different clients) are unlikely to happen in my use case, but I would prefer if they are handled properly (notification to the user). I've come across the following options, so far: something similar to Dropbox. iFolder seems to be the only thing that comes close, but its reputation (stability) and requirements put me off. A distributed file system such as OpenAFS. I'm not sure this will speed up file access. It is probably overkill for what I need. Maybe NFS or even Samba offer these possibilities. I read a bit about Windows' Offline Files, but its operation seems limited (at least on Windows XP). As this is just for personal use, I'm not willing to spend a lot of money. A free solution would be preferred. Also, the server needs to run on Linux, and I need a client for at least Windows.

  Read the article

• Issues with static IP (Ubuntu Server 10.04)

  - by letseatfood

  I am following this tutorial for setting up a testing server for my web development projects. When I attempt setting up a static IP address (using the configuration below), I receive the error "ping: unknown host www.google.com" when I attempt using ping. auto eth0 iface eth0 inet static address 192.168.0.100 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.1 Ping works fine when the configuration is: auto eth0 iface eth0 inet static I am a novice to server setup and administration.

  Read the article

• Ubuntu 12.10 Clock is wrong

  - by mardavi

  I have an issue with Ubuntu Quantal, as it shows the wrong time. It is completely messy, the right time from time.is now is 09.43 and my clock shows 17.48. I am using ntp service and I already checked the timezone and it is correct. I also checked the hardware clock through sudo hwclock --showsudo dpkg-reconfigure tzdata and this is right too. I also tried sudo dpkg-reconfigure tzdata but with bad luck. What else can I try? As asked, here my /etc/ntp.conf # /etc/ntp.conf, configuration for ntpd; see ntp.conf(5) for help driftfile /var/lib/ntp/ntp.drift # Enable this if you want statistics to be logged. #statsdir /var/log/ntpstats/ statistics loopstats peerstats clockstats filegen loopstats file loopstats type day enable filegen peerstats file peerstats type day enable filegen clockstats file clockstats type day enable # Specify one or more NTP servers. # Use servers from the NTP Pool Project. Approved by Ubuntu Technical Board # on 2011-02-08 (LP: #104525). See http://www.pool.ntp.org/join.html for # more information. server 0.ubuntu.pool.ntp.org server 1.ubuntu.pool.ntp.org server 2.ubuntu.pool.ntp.org server 3.ubuntu.pool.ntp.org server time.nist.gov # Use Ubuntu's ntp server as a fallback. server ntp.ubuntu.com # Access control configuration; see /usr/share/doc/ntp-doc/html/accopt.html for # details. The web page <http://support.ntp.org/bin/view/Support/AccessRestrictions> # might also be helpful. # # Note that "restrict" applies to both servers and clients, so a configuration # that might be intended to block requests from certain clients could also end # up blocking replies from your own upstream servers. # By default, exchange time with everybody, but don't allow configuration. restrict -4 default kod notrap nomodify nopeer noquery restrict -6 default kod notrap nomodify nopeer noquery # Local users may interrogate the ntp server more closely. restrict 127.0.0.1 restrict ::1 # Clients from this (example!) subnet have unlimited access, but only if # cryptographically authenticated. #restrict 192.168.123.0 mask 255.255.255.0 notrust # If you want to provide time to your local subnet, change the next line. # (Again, the address is an example only.) #broadcast 192.168.123.255 # If you want to listen to time broadcasts on your local subnet, de-comment the # next lines. Please do this only if you trust everybody on the network! #disable auth #broadcastclient In addition, the ntp service was not running when I turned on my laptop today.

  Read the article

• Deploying Django App with Nginx, Apache, mod_wsgi

  - by JCWong

  I have a django app which can run locally using the standard development environment. I want to now move this to EC2 for production. The django documentation suggests running with apache and mod_wsgi, and using nginx for loading static files. I am running Ubuntu 12.04 on an Ec2 box. My Django app, "ddt", contains a subdirectory "apache" with ddt.wsgi import os, sys apache_configuration= os.path.dirname(__file__) project = os.path.dirname(apache_configuration) workspace = os.path.dirname(project) sys.path.append(workspace) sys.path.append('/usr/lib/python2.7/site-packages/django/') sys.path.append('/home/jeffrey/www/ddt/') os.environ['DJANGO_SETTINGS_MODULE'] = 'ddt.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler() I have mod_wsgi installed from apt. My apache/httpd.conf contains NameVirtualHost *:8080 WSGIScriptAlias / /home/jeffrey/www/ddt/apache/ddt.wsgi WSGIPythonPath /home/jeffrey/www/ddt <Directory /home/jeffrey/www/ddt/apache/> <Files ddt.wsgi> Order deny,allow Allow from all </Files> </Directory> Under apache2/sites-enabled <VirtualHost *:8080> ServerName www.mysite.com ServerAlias mysite.com <Directory /home/jeffrey/www/ddt/apache/> Order deny,allow Allow from all </Directory> LogLevel warn ErrorLog /home/jeffrey/www/ddt/logs/apache_error.log CustomLog /home/jeffrey/www/ddt/logs/apache_access.log combined WSGIDaemonProcess datadriventrading.com user=www-data group=www-data threads=25 WSGIProcessGroup datadriventrading.com WSGIScriptAlias / /home/jeffrey/www/ddt/apache/ddt.wsgi </VirtualHost> If I am correct, these 3 files above should correctly allow my django app to run on port 8080. I have the following nginx/proxy.conf file proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffer_size 4k; proxy_buffers 4 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; Under nginx/sites-enabled server { listen 80; server_name www.mysite.com mysite.com; access_log /home/jeffrey/www/ddt/logs/nginx_access.log; error_log /home/jeffrey/www/ddt/logs/nginx_error.log; location / { proxy_pass http://127.0.0.1:8080; include /etc/nginx/proxy.conf; } location /media/ { root /home/jeffrey/www/ddt/; } } If I am correct these two files should setup nginx to take requests on the HTTP port 80, but then direct requests to apache which is running the django app on port 8080. If i go to mysite.com, all I see is Welcome to Nginx! Any advice for how to debug this?

  Read the article

• Lync Edge and Exchange Server: how to have access to my exchange mailbox from external network and also to the OWA

  - by Garcia Julien

  I've some problem in the configuration of Exchange 2010. My topology is like that: Server1 = Domain Controller Server2 = Exchange Server Server3 = Lync Server Server4 = Lync Edge Our public address (the one accessible by outside world) is directed to Server4. I would like to have access to my exchange mailbox from external network and also to the OWA. Could you help me in the configuration of thoses servers? Thank in advance Julien

  Read the article

• Can't upgrade my Ubuntu server, it gets stuck on openjdk-6-jre-headless

  - by Jean-Nicolas Boulay Desjardins

  I am using Ubuntu Server. When I do: apt-get upgrade it gets stuck on: Setting up openjdk-6-jre-headless (6b20-1.9.7-0ubuntu1) ... Why? And what can I do to stop it? I tried removing it with apt-get... I get this error: E: dpkg was interrupted, you must manually run 'sudo dpkg --configure -a' to correct the problem. So then I tried this: dpkg --purge openjdk-6-jre-headless I got this: dpkg: dependency problems prevent removal of openjdk-6-jre-headless: openjdk-6-jre-lib depends on openjdk-6-jre-headless (>= 6b17). ca-certificates-java depends on openjdk-6-jre-headless (>= 6b16-1.6.1-2) | java6-runtime-headless; however: Package openjdk-6-jre-headless is to be removed. Package java6-runtime-headless is not installed. Package openjdk-6-jre-headless which provides java6-runtime-headless is to be removed. ca-certificates-java depends on openjdk-6-jre-headless (>= 6b16-1.6.1-2) | java6-runtime-headless; however: Package openjdk-6-jre-headless is to be removed. Package java6-runtime-headless is not installed. Package openjdk-6-jre-headless which provides java6-runtime-headless is to be removed. dpkg: error processing openjdk-6-jre-headless (--purge): dependency problems - not removing Errors were encountered while processing: openjdk-6-jre-headless The thing is I think my DB is using it... Not sure... I am using Cassandra with Thrift... Yes, it's getting a bit more complex... # dpkg --configure -a I get: dpkg: dependency problems prevent configuration of openjdk-6-jre: openjdk-6-jre depends on openjdk-6-jre-headless (>= 6b20-1.9.7-0ubuntu1); however: Package openjdk-6-jre-headless is not configured yet. dpkg: error processing openjdk-6-jre (--configure): dependency problems - leaving unconfigured Processing triggers for libc-bin ... ldconfig deferred processing now taking place dpkg: dependency problems prevent configuration of libaccess-bridge-java: libaccess-bridge-java depends on default-jre | openjdk-6-jre | sun-java6-jre; however: Package default-jre is not installed. Package openjdk-6-jre is not configured yet. Package sun-java6-jre is not installed. dpkg: error processing libaccess-bridge-java (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of icedtea-6-jre-cacao: icedtea-6-jre-cacao depends on openjdk-6-jre-headless (= 6b20-1.9.7-0ubuntu1); however: Package openjdk-6-jre-headless is not configured yet. dpkg: error processing icedtea-6-jre-cacao (--configure): dependency problems - leaving unconfigured dpkg: dependency problems prevent configuration of libaccess-bridge-java-jni: libaccess-bridge-java-jni depends on libaccess-bridge-java (>= 1.26.2-5); however: Package libaccess-bridge-java is not configured yet. dpkg: error processing libaccess-bridge-java-jni (--configure): dependency problems - leaving unconfigured Errors were encountered while processing: openjdk-6-jre libaccess-bridge-java icedtea-6-jre-cacao libaccess-bridge-java-jni Thanks again for any help.

  Read the article

• How to configure apache and mod_proxy_ajp in order to forward ssl client certificate

  - by giovanni.cuccu

  Hi, I've developed a java application that need a ssl client certificate and in the staging environment with apache 2.2 and mod_jk it is working fine. In production the configuration is not using mod_jk but mod_proxy_ajp. I'm looking for an apache configuration example that configure ssl and mod_proxy_ajp for sending the ssl client certificate to the java application server (which listens with the ajp protocol). Thanks a lot

  Read the article

• HP DL380 G7 Disk swap to a HP DL380 G6

  - by rnuno

  The HP DL380 G7 has 3 SAS disks in RAID 5 configuration. I need to change that server to another task and instead of make a clean install on the HP DL380 G6 can i just swap the 3 disks from HP DL380 G7 to the HP DL380 G6? I expect some driver issues maybe on the OS itself because the processor is different. They both use Smart Array P410i, if i power down the machines swap the disk by the same order will the RAID 5 configuration remain and the OS will boot?

  Read the article

• Debian + ProFTPD + LDAP Incorrect Password Issue

  - by Tristan Hall

  I have the LDAP configuration configured for ProFTPD and I have modified the modules.conf file to include the LDAP module. However, every time I login with FileZilla I get 530 Login Incorrect. It does this for all users except those whose passwords are defined locally as well as in LDAP. The exact same setup works fine on my CentOS server and I've already tried re-installing it after purging the configuration files.

  Read the article

• SCOM2012 monitor detail changes on switch

  - by siyang

  Could I use SCOM2012 monitor the changes on switch(CISCO 3750 2960 4906 etc), such as VLAN changes, Port shutdown, open any services on switch. I noticed there is one reports named configuration changes report, but seems like no any detail configuration could be monitor on switch? Should I download any MP to monitor the detail changes on SW. Really appreciated your suggestion. Thanks and Regards Siyang

  Read the article

• Automate the installation of postfix on Ubuntu

  - by sutch

  My system configuration script does an "apt-get install -y postfix". Unfortunately the script is halted when the postfix installer displays a configuration page. Is there a method to force postfix to use the defaults during installation so that an automated script can continue to the end?

  Read the article

< Previous Page | 500 501 502 503 504 505 506 507 508 509 510 511  | Next Page >