Search Results

Search found 12705 results on 509 pages for 'random sample'.

Page 505/509 | < Previous Page | 501 502 503 504 505 506 507 508 509  | Next Page >

• How do I prevent TCP connection freezes over an OpenVPN network?

  - by Jason R

  New details added at the end of this question; it's possible that I'm zeroing in on the cause. I have a UDP OpenVPN-based VPN set up in tap mode (I need tap because I need the VPN to pass multicast packets, which doesn't seem to be possible with tun networks) with a handful of clients across the Internet. I've been experiencing frequent TCP connection freezes over the VPN. That is, I will establish a TCP connection (e.g. an SSH connection, but other protocols have similar issues), and at some point during the session, it seems that traffic will cease being transmitted over that TCP session. This seems to be related to points at which large data transfers occur, such as if I execute an ls command in an SSH session, or if I cat a long log file. Some Google searches turn up a number of answers like this previous one on Server Fault, indicating that the likely culprit is an MTU issue: that during periods of high traffic, the VPN is trying to send packets that get dropped somewhere in the pipes between the VPN endpoints. The above-linked answer suggests using the following OpenVPN configuration settings to mitigate the problem: fragment 1400 mssfix This should limit the MTU used on the VPN to 1400 bytes and fix the TCP maximum segment size to prevent the generation of any packets larger than that. This seems to mitigate the problem a bit, but I still frequently see the freezes. I've tried a number of sizes as arguments to the fragment directive: 1200, 1000, 576, all with similar results. I can't think of any strange network topology between the two ends that could trigger such a problem: the VPN server is running on a pfSense machine connected directly to the Internet, and my client is also connected directly to the Internet at another location. One other strange piece of the puzzle: if I run the tracepath utility, then that seems to band-aid the problem. A sample run looks like: [~]$ tracepath -n 192.168.100.91 1: 192.168.100.90 0.039ms pmtu 1500 1: 192.168.100.91 40.823ms reached 1: 192.168.100.91 19.846ms reached Resume: pmtu 1500 hops 1 back 64 The above run is between two clients on the VPN: I initiated the trace from 192.168.100.90 to the destination of 192.168.100.91. Both clients were configured with fragment 1200; mssfix; in an attempt to limit the MTU used on the link. The above results would seem to suggest that tracepath was able to detect a path MTU of 1500 bytes between the two clients. I would assume that it would be somewhat smaller due to the fragmentation settings specified in the OpenVPN configuration. I found that result somewhat strange. Even stranger, however: if I have a TCP connection in the stalled state (e.g. an SSH session with a directory listing that froze in the middle), then executing the tracepath command shown above causes the connection to start up again! I can't figure out any reasonable explanation for why this would be the case, but I feel like this might be pointing toward a solution to ultimately eradicate the problem. Does anyone have any recommendations for other things to try? Edit: I've come back and looked at this a bit further, and have found only more confounding information: I set the OpenVPN connection to fragment at 1400 bytes, as shown above. Then, I connected to the VPN from across the Internet and used Wireshark to look at the UDP packets that were sent to the VPN server while the stall occurred. None were greater than the specified 1400 byte count, so the fragmentation seems to be functioning properly. To verify that even a 1400-byte MTU would be sufficient, I pinged the VPN server using the following (Linux) command: ping <host> -s 1450 -M do This (I believe) sends a 1450-byte packet with fragmentation disabled (I at least verified that it didn't work if I set it to an obviously-too-large value like 1600 bytes). These seem to work just fine; I get replies back from the host with no issue. So, maybe this isn't an MTU issue at all. I'm just confused as to what else it might be! Edit 2: The rabbit hole just keeps getting deeper: I've now isolated the problem a bit more. It seems to be related to the exact OS that the VPN client uses. I have successfully duplicated the problem on at least three Ubuntu machines (versions 12.04 through 13.04). I can reliably duplicate an SSH connection freeze within a minute or so by just cat-ing a large log file. However, if I do the same test using a CentOS 6 machine as a client, then I don't see the problem! I've tested using the exact same OpenVPN client version as I was using on the Ubuntu machines. I can cat log files for hours without seeing the connection freeze. This seems to provide some insight as to the ultimate cause, but I'm just not sure what that insight is. I have examined the traffic over the VPN using Wireshark. I'm not a TCP expert, so I'm not sure what to make of the gory details, but the gist is that at some point, a UDP packet gets dropped due to the limited bandwidth of the Internet link, causing TCP retransmissions inside the VPN tunnel. On the CentOS client, these retransmissions occur properly and things move on happily. At some point with the Ubuntu clients, though, the remote end starts retransmitting the same TCP segment over and over (with the transmit delay increasing between each retransmission). The client sends what looks like a valid TCP ACK to each retransmission, but the remote end still continues to transmit the same TCP segment periodically. This extends ad infinitum and the connection stalls. My question here would be: Does anyone have any recommendations for how to troubleshoot and/or determine the root cause of the TCP issue? It's as if the remote end isn't accepting the ACK messages sent by the VPN client. One common difference between the CentOS node and the various Ubuntu releases is that Ubuntu has a much more recent Linux kernel version (from 3.2 in Ubuntu 12.04 to 3.8 in 13.04). A pointer to some new kernel bug maybe? I'm assuming that if that were so, then I wouldn't be the only one experiencing the problem; I don't think this seems like a particularly exotic setup.

  Read the article

• Linux server is only using 60% of memory, then swapping

  - by Kamil Kisiel

  I've got a Linux server that's running our bacula backup system. The machine is grinding like mad because it's going heavy in to swap. The problem is, it's only using 60% of its physical memory! Here's the output from free -m: free -m total used free shared buffers cached Mem: 3949 2356 1593 0 0 1 -/+ buffers/cache: 2354 1595 Swap: 7629 1804 5824 and some sample output from vmstat 1: procs -----------memory---------- ---swap-- -----io---- -system-- -----cpu------ r b swpd free buff cache si so bi bo in cs us sy id wa st 0 2 1843536 1634512 0 4188 54 13 2524 666 2 1 1 1 89 9 0 1 11 1845916 1640724 0 388 2700 4816 221880 4879 14409 170721 4 3 63 30 0 0 9 1846096 1643952 0 0 4956 756 174832 804 12357 159306 3 4 63 30 0 0 11 1846104 1643532 0 0 4916 540 174320 580 10609 139960 3 4 64 29 0 0 4 1846084 1640272 0 2336 4080 524 140408 548 9331 118287 3 4 63 30 0 0 8 1846104 1642096 0 1488 2940 432 102516 457 7023 82230 2 4 65 29 0 0 5 1846104 1642268 0 1276 3704 452 126520 452 9494 119612 3 5 65 27 0 3 12 1846104 1641528 0 328 6092 608 187776 636 8269 113059 4 3 64 29 0 2 2 1846084 1640960 0 724 5948 0 111480 0 7751 116370 4 4 63 29 0 0 4 1846100 1641484 0 404 4144 1476 125760 1500 10668 105358 2 3 71 25 0 0 13 1846104 1641932 0 0 5872 828 153808 840 10518 128447 3 4 70 22 0 0 8 1846096 1639172 0 3164 3556 556 74884 580 5082 65362 2 2 73 23 0 1 4 1846080 1638676 0 396 4512 28 50928 44 2672 38277 2 2 80 16 0 0 3 1846080 1628808 0 7132 2636 0 28004 8 1358 14090 0 1 78 20 0 0 2 1844728 1618552 0 11140 7680 0 12740 8 763 2245 0 0 82 18 0 0 2 1837764 1532056 0 101504 2952 0 95644 24 802 3817 0 1 87 12 0 0 11 1842092 1633324 0 4416 1748 10900 143144 11024 6279 134442 3 3 70 24 0 2 6 1846104 1642756 0 0 4768 468 78752 468 4672 60141 2 2 76 20 0 1 12 1846104 1640792 0 236 4752 440 140712 464 7614 99593 3 5 58 34 0 0 3 1846084 1630368 0 6316 5104 0 20336 0 1703 22424 1 1 72 26 0 2 17 1846104 1638332 0 3168 4080 1720 211960 1744 11977 155886 3 4 65 28 0 1 10 1846104 1640800 0 132 4488 556 126016 584 8016 106368 3 4 63 29 0 0 14 1846104 1639740 0 2248 3436 428 114188 452 7030 92418 3 3 59 35 0 1 6 1846096 1639504 0 1932 5500 436 141412 460 8261 112210 4 4 63 29 0 0 10 1846104 1640164 0 3052 4028 448 147684 472 7366 109554 4 4 61 30 0 0 10 1846100 1641040 0 2332 4952 632 147452 664 8767 118384 3 4 63 30 0 4 8 1846084 1641092 0 664 4948 276 152264 292 6448 98813 5 5 62 28 0 Furthermore, the output of top sorted by CPU time seems to support the theory that swap is what's bogging down the system: top - 09:05:32 up 37 days, 23:24, 1 user, load average: 9.75, 8.24, 7.12 Tasks: 173 total, 1 running, 172 sleeping, 0 stopped, 0 zombie Cpu(s): 1.6%us, 1.4%sy, 0.0%ni, 76.1%id, 20.6%wa, 0.1%hi, 0.2%si, 0.0%st Mem: 4044632k total, 2405628k used, 1639004k free, 0k buffers Swap: 7812492k total, 1851852k used, 5960640k free, 436k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ TIME COMMAND 4174 root 17 0 63156 176 56 S 8 0.0 2138:52 35,38 bacula-fd 4185 root 17 0 63352 284 104 S 6 0.0 1709:25 28,29 bacula-sd 240 root 15 0 0 0 0 D 3 0.0 831:55.19 831:55 kswapd0 2852 root 10 -5 0 0 0 S 1 0.0 126:35.59 126:35 xfsbufd 2849 root 10 -5 0 0 0 S 0 0.0 119:50.94 119:50 xfsbufd 1364 root 10 -5 0 0 0 S 0 0.0 117:05.39 117:05 xfsbufd 21 root 10 -5 0 0 0 S 1 0.0 48:03.44 48:03 events/3 6940 postgres 16 0 43596 8 8 S 0 0.0 46:50.35 46:50 postmaster 1342 root 10 -5 0 0 0 S 0 0.0 23:14.34 23:14 xfsdatad/4 5415 root 17 0 1770m 108 48 S 0 0.0 15:03.74 15:03 bacula-dir 23 root 10 -5 0 0 0 S 0 0.0 13:09.71 13:09 events/5 5604 root 17 0 1216m 500 200 S 0 0.0 12:38.20 12:38 java 5552 root 16 0 1194m 580 248 S 0 0.0 11:58.00 11:58 java Here's the same sorted by virtual memory image size: top - 09:08:32 up 37 days, 23:27, 1 user, load average: 8.43, 8.26, 7.32 Tasks: 173 total, 1 running, 172 sleeping, 0 stopped, 0 zombie Cpu(s): 3.6%us, 3.4%sy, 0.0%ni, 62.2%id, 30.2%wa, 0.2%hi, 0.3%si, 0.0%st Mem: 4044632k total, 2404212k used, 1640420k free, 0k buffers Swap: 7812492k total, 1852548k used, 5959944k free, 100k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ TIME COMMAND 5415 root 17 0 1770m 56 44 S 0 0.0 15:03.78 15:03 bacula-dir 5604 root 17 0 1216m 492 200 S 0 0.0 12:38.30 12:38 java 5552 root 16 0 1194m 476 200 S 0 0.0 11:58.20 11:58 java 4598 root 16 0 117m 44 44 S 0 0.0 0:13.37 0:13 eventmond 9614 gdm 16 0 93188 0 0 S 0 0.0 0:00.30 0:00 gdmgreeter 5527 root 17 0 78716 0 0 S 0 0.0 0:00.30 0:00 gdm 4185 root 17 0 63352 284 104 S 20 0.0 1709:52 28,29 bacula-sd 4174 root 17 0 63156 208 88 S 24 0.0 2139:25 35,39 bacula-fd 10849 postgres 18 0 54740 216 108 D 0 0.0 0:31.40 0:31 postmaster 6661 postgres 17 0 49432 0 0 S 0 0.0 0:03.50 0:03 postmaster 5507 root 15 0 47980 0 0 S 0 0.0 0:00.00 0:00 gdm 6940 postgres 16 0 43596 16 16 S 0 0.0 46:51.39 46:51 postmaster 5304 postgres 16 0 40580 132 88 S 0 0.0 6:21.79 6:21 postmaster 5301 postgres 17 0 40448 24 24 S 0 0.0 0:32.17 0:32 postmaster 11280 root 16 0 40288 28 28 S 0 0.0 0:00.11 0:00 sshd 5534 root 17 0 37580 0 0 S 0 0.0 0:56.18 0:56 X 30870 root 30 15 31668 28 28 S 0 0.0 1:13.38 1:13 snmpd 5305 postgres 17 0 30628 16 16 S 0 0.0 0:11.60 0:11 postmaster 27403 postfix 17 0 30248 0 0 S 0 0.0 0:02.76 0:02 qmgr 10815 postfix 15 0 30208 16 16 S 0 0.0 0:00.02 0:00 pickup 5306 postgres 16 0 29760 20 20 S 0 0.0 0:52.89 0:52 postmaster 5302 postgres 17 0 29628 64 32 S 0 0.0 1:00.64 1:00 postmaster I've tried tuning the swappiness kernel parameter to both high and low values, but nothing appears to change the behavior here. I'm at a loss to figure out what's going on. How can I find out what's causing this? Update: The system is a fully 64-bit system, so there should be no question of memory limitations due to 32-bit issues. Update2: As I mentioned in the original question, I've already tried tuning swappiness to all sorts of values, including 0. The result is always the same, with approximately 1.6 GB of memory remaining unused. Update3: Added top output to the above info.

  Read the article

• Help getting frame rate (fps) up in Python + Pygame

  - by Jordan Magnuson

  I am working on a little card-swapping world-travel game that I sort of envision as a cross between Bejeweled and the 10 Days geography board games. So far the coding has been going okay, but the frame rate is pretty bad... currently I'm getting low 20's on my Core 2 Duo. This is a problem since I'm creating the game for Intel's March developer competition, which is squarely aimed at netbooks packing underpowered Atom processors. Here's a screen from the game: ![www.necessarygames.com/my_games/betraveled/betraveled-fps.png][1] I am very new to Python and Pygame (this is the first thing I've used them for), and am sadly lacking in formal CS training... which is to say that I think there are probably A LOT of bad practices going on in my code, and A LOT that could be optimized. If some of you older Python hands wouldn't mind taking a look at my code and seeing if you can't find any obvious areas for optimization, I would be extremely grateful. You can download the full source code here: http://www.necessarygames.com/my_games/betraveled/betraveled_src0328.zip Compiled exe here: www.necessarygames.com/my_games/betraveled/betraveled_src0328.zip One thing I am concerned about is my event manager, which I feel may have some performance wholes in it, and another thing is my rendering... I'm pretty much just blitting everything to the screen all the time (see the render routines in my game_components.py below); I recently found out that you should only update the areas of the screen that have changed, but I'm still foggy on how that accomplished exactly... could this be a huge performance issue? Any thoughts are much appreciated! As usual, I'm happy to "tip" you for your time and energy via PayPal. Jordan Here are some bits of the source: Main.py #Remote imports import pygame from pygame.locals import * #Local imports import config import rooms from event_manager import * from events import * class RoomController(object): """Controls which room is currently active (eg Title Screen)""" def __init__(self, screen, ev_manager): self.room = None self.screen = screen self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.room = self.set_room(config.room) def set_room(self, room_const): #Unregister old room from ev_manager if self.room: self.room.ev_manager.unregister_listener(self.room) self.room = None #Set new room based on const if room_const == config.TITLE_SCREEN: return rooms.TitleScreen(self.screen, self.ev_manager) elif room_const == config.GAME_MODE_ROOM: return rooms.GameModeRoom(self.screen, self.ev_manager) elif room_const == config.GAME_ROOM: return rooms.GameRoom(self.screen, self.ev_manager) elif room_const == config.HIGH_SCORES_ROOM: return rooms.HighScoresRoom(self.screen, self.ev_manager) def notify(self, event): if isinstance(event, ChangeRoomRequest): if event.game_mode: config.game_mode = event.game_mode self.room = self.set_room(event.new_room) def render(self, surface): self.room.render(surface) #Run game def main(): pygame.init() screen = pygame.display.set_mode(config.screen_size) ev_manager = EventManager() spinner = CPUSpinnerController(ev_manager) room_controller = RoomController(screen, ev_manager) pygame_event_controller = PyGameEventController(ev_manager) spinner.run() # this runs the main function if this script is called to run. # If it is imported as a module, we don't run the main function. if __name__ == "__main__": main() event_manager.py #Remote imports import pygame from pygame.locals import * #Local imports import config from events import * def debug( msg ): print "Debug Message: " + str(msg) class EventManager: #This object is responsible for coordinating most communication #between the Model, View, and Controller. def __init__(self): from weakref import WeakKeyDictionary self.listeners = WeakKeyDictionary() self.eventQueue= [] self.gui_app = None #---------------------------------------------------------------------- def register_listener(self, listener): self.listeners[listener] = 1 #---------------------------------------------------------------------- def unregister_listener(self, listener): if listener in self.listeners: del self.listeners[listener] #---------------------------------------------------------------------- def post(self, event): if isinstance(event, MouseButtonLeftEvent): debug(event.name) #NOTE: copying the list like this before iterating over it, EVERY tick, is highly inefficient, #but currently has to be done because of how new listeners are added to the queue while it is running #(eg when popping cards from a deck). Should be changed. See: http://dr0id.homepage.bluewin.ch/pygame_tutorial08.html #and search for "Watch the iteration" for listener in list(self.listeners): #NOTE: If the weakref has died, it will be #automatically removed, so we don't have #to worry about it. listener.notify(event) #------------------------------------------------------------------------------ class PyGameEventController: """...""" def __init__(self, ev_manager): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.input_freeze = False #---------------------------------------------------------------------- def notify(self, incoming_event): if isinstance(incoming_event, UserInputFreeze): self.input_freeze = True elif isinstance(incoming_event, UserInputUnFreeze): self.input_freeze = False elif isinstance(incoming_event, TickEvent): #Share some time with other processes, so we don't hog the cpu pygame.time.wait(5) #Handle Pygame Events for event in pygame.event.get(): #If this event manager has an associated PGU GUI app, notify it of the event if self.ev_manager.gui_app: self.ev_manager.gui_app.event(event) #Standard event handling for everything else ev = None if event.type == QUIT: ev = QuitEvent() elif event.type == pygame.MOUSEBUTTONDOWN and not self.input_freeze: if event.button == 1: #Button 1 pos = pygame.mouse.get_pos() ev = MouseButtonLeftEvent(pos) elif event.type == pygame.MOUSEMOTION: pos = pygame.mouse.get_pos() ev = MouseMoveEvent(pos) #Post event to event manager if ev: self.ev_manager.post(ev) #------------------------------------------------------------------------------ class CPUSpinnerController: def __init__(self, ev_manager): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.clock = pygame.time.Clock() self.cumu_time = 0 self.keep_going = True #---------------------------------------------------------------------- def run(self): if not self.keep_going: raise Exception('dead spinner') while self.keep_going: time_passed = self.clock.tick() fps = self.clock.get_fps() self.cumu_time += time_passed self.ev_manager.post(TickEvent(time_passed, fps)) if self.cumu_time >= 1000: self.cumu_time = 0 self.ev_manager.post(SecondEvent()) pygame.quit() #---------------------------------------------------------------------- def notify(self, event): if isinstance(event, QuitEvent): #this will stop the while loop from running self.keep_going = False rooms.py #Remote imports import pygame #Local imports import config import continents from game_components import * from my_gui import * from pgu import high class Room(object): def __init__(self, screen, ev_manager): self.screen = screen self.ev_manager = ev_manager self.ev_manager.register_listener(self) def notify(self, event): if isinstance(event, TickEvent): pygame.display.set_caption('FPS: ' + str(int(event.fps))) self.render(self.screen) pygame.display.update() def get_highs_table(self): fname = 'high_scores.txt' highs_table = None config.all_highs = high.Highs(fname) if config.game_mode == config.TIME_CHALLENGE: if config.difficulty == config.EASY: highs_table = config.all_highs['time_challenge_easy'] if config.difficulty == config.MED_DIF: highs_table = config.all_highs['time_challenge_med'] if config.difficulty == config.HARD: highs_table = config.all_highs['time_challenge_hard'] if config.difficulty == config.SUPER: highs_table = config.all_highs['time_challenge_super'] elif config.game_mode == config.PLAN_AHEAD: pass return highs_table class TitleScreen(Room): def __init__(self, screen, ev_manager): Room.__init__(self, screen, ev_manager) self.background = pygame.image.load('assets/images/interface/background.jpg').convert() #Initialize #--------------------------------------- self.gui_form = gui.Form() self.gui_app = gui.App(config.gui_theme) self.ev_manager.gui_app = self.gui_app c = gui.Container(align=0,valign=0) #Quit Button #--------------------------------------- b = StartGameButton(ev_manager=self.ev_manager) c.add(b, 0, 0) self.gui_app.init(c) def render(self, surface): surface.blit(self.background, (0, 0)) #GUI self.gui_app.paint(surface) class GameModeRoom(Room): def __init__(self, screen, ev_manager): Room.__init__(self, screen, ev_manager) self.background = pygame.image.load('assets/images/interface/background.jpg').convert() self.create_gui() #Create pgu gui elements def create_gui(self): #Setup #--------------------------------------- self.gui_form = gui.Form() self.gui_app = gui.App(config.gui_theme) self.ev_manager.gui_app = self.gui_app c = gui.Container(align=0,valign=-1) #Mode Relaxed Button #--------------------------------------- b = GameModeRelaxedButton(ev_manager=self.ev_manager) self.b = b print b.rect c.add(b, 0, 200) #Mode Time Challenge Button #--------------------------------------- b = TimeChallengeButton(ev_manager=self.ev_manager) self.b = b print b.rect c.add(b, 0, 250) #Mode Think Ahead Button #--------------------------------------- # b = PlanAheadButton(ev_manager=self.ev_manager) # self.b = b # print b.rect # c.add(b, 0, 300) #Initialize #--------------------------------------- self.gui_app.init(c) def render(self, surface): surface.blit(self.background, (0, 0)) #GUI self.gui_app.paint(surface) class GameRoom(Room): def __init__(self, screen, ev_manager): Room.__init__(self, screen, ev_manager) #Game mode #--------------------------------------- self.new_board_timer = None self.game_mode = config.game_mode config.current_highs = self.get_highs_table() self.highs_dialog = None self.game_over = False #Images #--------------------------------------- self.background = pygame.image.load('assets/images/interface/game screen2-1.jpg').convert() self.logo = pygame.image.load('assets/images/interface/logo_small.png').convert_alpha() self.game_over_text = pygame.image.load('assets/images/interface/text_game_over.png').convert_alpha() self.trip_complete_text = pygame.image.load('assets/images/interface/text_trip_complete.png').convert_alpha() self.zoom_game_over = None self.zoom_trip_complete = None self.fade_out = None #Text #--------------------------------------- self.font = pygame.font.Font(config.font_sans, config.interface_font_size) #Create game components #--------------------------------------- self.continent = self.set_continent(config.continent) self.board = Board(config.board_size, self.ev_manager) self.deck = Deck(self.ev_manager, self.continent) self.map = Map(self.continent) self.longest_trip = 0 #Set pos of game components #--------------------------------------- board_pos = (SCREEN_MARGIN[0], 109) self.board.set_pos(board_pos) map_pos = (config.screen_size[0] - self.map.size[0] - SCREEN_MARGIN[0], 57); self.map.set_pos(map_pos) #Trackers #--------------------------------------- self.game_clock = Chrono(self.ev_manager) self.swap_counter = 0 self.level = 0 #Create gui #--------------------------------------- self.create_gui() #Create initial board #--------------------------------------- self.new_board = self.deck.deal_new_board(self.board) self.ev_manager.post(NewBoardComplete(self.new_board)) def set_continent(self, continent_const): #Set continent based on const if continent_const == config.EUROPE: return continents.Europe() if continent_const == config.AFRICA: return continents.Africa() else: raise Exception('Continent constant not recognized') #Create pgu gui elements def create_gui(self): #Setup #--------------------------------------- self.gui_form = gui.Form() self.gui_app = gui.App(config.gui_theme) self.ev_manager.gui_app = self.gui_app c = gui.Container(align=-1,valign=-1) #Timer Progress bar #--------------------------------------- self.timer_bar = None self.time_increase = None self.minutes_left = None self.seconds_left = None self.timer_text = None if self.game_mode == config.TIME_CHALLENGE: self.time_increase = config.time_challenge_start_time self.timer_bar = gui.ProgressBar(config.time_challenge_start_time,0,config.max_time_bank,width=306) c.add(self.timer_bar, 172, 57) #Connections Progress bar #--------------------------------------- self.connections_bar = None self.connections_bar = gui.ProgressBar(0,0,config.longest_trip_needed,width=306) c.add(self.connections_bar, 172, 83) #Quit Button #--------------------------------------- b = QuitButton(ev_manager=self.ev_manager) c.add(b, 950, 20) #Generate Board Button #--------------------------------------- b = GenerateBoardButton(ev_manager=self.ev_manager, room=self) c.add(b, 500, 20) #Board Size? #--------------------------------------- bs = SetBoardSizeContainer(config.BOARD_LARGE, ev_manager=self.ev_manager, board=self.board) c.add(bs, 640, 20) #Fill Board? #--------------------------------------- t = FillBoardCheckbox(config.fill_board, ev_manager=self.ev_manager) c.add(t, 740, 20) #Darkness? #--------------------------------------- t = UseDarknessCheckbox(config.use_darkness, ev_manager=self.ev_manager) c.add(t, 840, 20) #Initialize #--------------------------------------- self.gui_app.init(c) def advance_level(self): self.level += 1 print 'Advancing to next level' print 'New level: ' + str(self.level) if self.timer_bar: print 'Time increase: ' + str(self.time_increase) self.timer_bar.value += self.time_increase self.time_increase = max(config.min_advance_time, int(self.time_increase * 0.9)) self.board = self.new_board self.new_board = None self.zoom_trip_complete = None self.game_clock.unpause() def notify(self, event): #Tick event if isinstance(event, TickEvent): pygame.display.set_caption('FPS: ' + str(int(event.fps))) self.render(self.screen) pygame.display.update() #Wait to deal new board when advancing levels if self.zoom_trip_complete and self.zoom_trip_complete.finished: self.zoom_trip_complete = None self.ev_manager.post(UnfreezeCards()) self.new_board = self.deck.deal_new_board(self.board) self.ev_manager.post(NewBoardComplete(self.new_board)) #New high score? if self.zoom_game_over and self.zoom_game_over.finished and not self.highs_dialog: if config.current_highs.check(self.level) != None: self.zoom_game_over.visible = False data = 'time:' + str(self.game_clock.time) + ',swaps:' + str(self.swap_counter) self.highs_dialog = HighScoreDialog(score=self.level, data=data, ev_manager=self.ev_manager) self.highs_dialog.open() elif not self.fade_out: self.fade_out = FadeOut(self.ev_manager, config.TITLE_SCREEN) #Second event elif isinstance(event, SecondEvent): if self.timer_bar: if not self.game_clock.paused: self.timer_bar.value -= 1 if self.timer_bar.value <= 0 and not self.game_over: self.ev_manager.post(GameOver()) self.minutes_left = self.timer_bar.value / 60 self.seconds_left = self.timer_bar.value % 60 if self.seconds_left < 10: leading_zero = '0' else: leading_zero = '' self.timer_text = ''.join(['Time Left: ', str(self.minutes_left), ':', leading_zero, str(self.seconds_left)]) #Game over elif isinstance(event, GameOver): self.game_over = True self.zoom_game_over = ZoomImage(self.ev_manager, self.game_over_text) #Trip complete event elif isinstance(event, TripComplete): print 'You did it!' self.game_clock.pause() self.zoom_trip_complete = ZoomImage(self.ev_manager, self.trip_complete_text) self.new_board_timer = Timer(self.ev_manager, 2) self.ev_manager.post(FreezeCards()) print 'Room posted newboardcomplete' #Board Refresh Complete elif isinstance(event, BoardRefreshComplete): if event.board == self.board: print 'Longest trip needed: ' + str(config.longest_trip_needed) print 'Your longest trip: ' + str(self.board.longest_trip) if self.board.longest_trip >= config.longest_trip_needed: self.ev_manager.post(TripComplete()) elif event.board == self.new_board: self.advance_level() self.connections_bar.value = self.board.longest_trip self.connection_text = ' '.join(['Connections:', str(self.board.longest_trip), '/', str(config.longest_trip_needed)]) #CardSwapComplete elif isinstance(event, CardSwapComplete): self.swap_counter += 1 elif isinstance(event, ConfigChangeBoardSize): config.board_size = event.new_size elif isinstance(event, ConfigChangeCardSize): config.card_size = event.new_size elif isinstance(event, ConfigChangeFillBoard): config.fill_board = event.new_value elif isinstance(event, ConfigChangeDarkness): config.use_darkness = event.new_value def render(self, surface): #Background surface.blit(self.background, (0, 0)) #Map self.map.render(surface) #Board self.board.render(surface) #Logo surface.blit(self.logo, (10,10)) #Text connection_text = self.font.render(self.connection_text, True, BLACK) surface.blit(connection_text, (25, 84)) if self.timer_text: timer_text = self.font.render(self.timer_text, True, BLACK) surface.blit(timer_text, (25, 64)) #GUI self.gui_app.paint(surface) if self.zoom_trip_complete: self.zoom_trip_complete.render(surface) if self.zoom_game_over: self.zoom_game_over.render(surface) if self.fade_out: self.fade_out.render(surface) class HighScoresRoom(Room): def __init__(self, screen, ev_manager): Room.__init__(self, screen, ev_manager) self.background = pygame.image.load('assets/images/interface/background.jpg').convert() #Initialize #--------------------------------------- self.gui_app = gui.App(config.gui_theme) self.ev_manager.gui_app = self.gui_app c = gui.Container(align=0,valign=0) #High Scores Table #--------------------------------------- hst = HighScoresTable() c.add(hst, 0, 0) self.gui_app.init(c) def render(self, surface): surface.blit(self.background, (0, 0)) #GUI self.gui_app.paint(surface) game_components.py #Remote imports import pygame from pygame.locals import * import random import operator from copy import copy from math import sqrt, floor #Local imports import config from events import * from matrix import Matrix from textrect import render_textrect, TextRectException from hyphen import hyphenator from textwrap2 import TextWrapper ############################## #CONSTANTS ############################## SCREEN_MARGIN = (10, 10) #Colors BLACK = (0, 0, 0) WHITE = (255, 255, 255) RED = (255, 0, 0) YELLOW = (255, 200, 0) #Directions LEFT = -1 RIGHT = 1 UP = 2 DOWN = -2 #Cards CARD_MARGIN = (10, 10) CARD_PADDING = (2, 2) #Card types BLANK = 0 COUNTRY = 1 TRANSPORT = 2 #Transport types PLANE = 0 TRAIN = 1 CAR = 2 SHIP = 3 class Timer(object): def __init__(self, ev_manager, time_left): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.time_left = time_left self.paused = False def __repr__(self): return str(self.time_left) def pause(self): self.paused = True def unpause(self): self.paused = False def notify(self, event): #Pause Event if isinstance(event, Pause): self.pause() #Unpause Event elif isinstance(event, Unpause): self.unpause() #Second Event elif isinstance(event, SecondEvent): if not self.paused: self.time_left -= 1 class Chrono(object): def __init__(self, ev_manager, start_time=0): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.time = start_time self.paused = False def __repr__(self): return str(self.time_left) def pause(self): self.paused = True def unpause(self): self.paused = False def notify(self, event): #Pause Event if isinstance(event, Pause): self.pause() #Unpause Event elif isinstance(event, Unpause): self.unpause() #Second Event elif isinstance(event, SecondEvent): if not self.paused: self.time += 1 class Map(object): def __init__(self, continent): self.map_image = pygame.image.load(continent.map).convert_alpha() self.map_text = pygame.image.load(continent.map_text).convert_alpha() self.pos = (0, 0) self.set_color() self.map_image = pygame.transform.smoothscale(self.map_image, config.map_size) self.size = self.map_image.get_size() def set_pos(self, pos): self.pos = pos def set_color(self): image_pixel_array = pygame.PixelArray(self.map_image) image_pixel_array.replace(config.GRAY1, config.COLOR1) image_pixel_array.replace(config.GRAY2, config.COLOR2) image_pixel_array.replace(config.GRAY3, config.COLOR3) image_pixel_array.replace(config.GRAY4, config.COLOR4) image_pixel_array.replace(config.GRAY5, config.COLOR5)

  Read the article

• SPP Socket createRfcommSocketToServiceRecord will not connect

  - by philDev

  Hello, I want to use Android 2.1 to connect to an external Bluetooth device, wich is offering an SPP port to me. In this case it is an external GPS unit. When I'm trying to connect I can't connect an established socket while being in the "client" mode. Then if I try to set up a socket (being in the server role), to RECEIVE text from my PC everything works just fine. The Computer can connect as the client to the Socket on the Phone via SPP using the SSP UUID or some random UUID. So the Problem is not that I'm using the wrong UUID. But the other way around (e.g. calling connect on the established client socket) createRfcommSocketToServiceRecord(UUID uuid)) just doesn't work. Sadly I don't have the time to inspect the problem further. It would be greate If somebody could point me the right way. In the following part of the Logfile has to be the Problem. Greets PhilDev P.S. I'm going to be present during the Office hours. Here the log file: 03-21 03:10:52.020: DEBUG/BluetoothSocket.cpp(4643): initSocketFromFdNative 03-21 03:10:52.025: DEBUG/BluetoothSocket(4643): connect 03-21 03:10:52.025: DEBUG/BluetoothSocket(4643): doSdp 03-21 03:10:52.050: DEBUG/ADAPTER(2132): create_device(01:00:00:7F:B5:B3) 03-21 03:10:52.050: DEBUG/ADAPTER(2132): adapter_create_device(01:00:00:7F:B5:B3) 03-21 03:10:52.055: DEBUG/DEVICE(2132): Creating device [address = 01:00:00:7F:B5:B3] /org/bluez/2132/hci0/dev_01_00_00_7F_B5_B3 [name = ] 03-21 03:10:52.055: DEBUG/DEVICE(2132): btd_device_ref(0x10c18): ref=1 03-21 03:10:52.065: INFO/BluetoothEventLoop.cpp(1914): event_filter: Received signal org.bluez.Adapter:DeviceCreated from /org/bluez/2132/hci0 03-21 03:10:52.065: INFO/BluetoothService.cpp(1914): ... Object Path = /org/bluez/2132/hci0/dev_01_00_00_7F_B5_B3 03-21 03:10:52.065: INFO/BluetoothService.cpp(1914): ... Pattern = 00001101-0000-1000-8000-00805f9b34fb, strlen = 36 03-21 03:10:52.070: DEBUG/DEVICE(2132): *************DiscoverServices******** 03-21 03:10:52.070: INFO/DTUN_HCID(2132): dtun_client_get_remote_svc_channel: starting discovery on (uuid16=0x0011) 03-21 03:10:52.070: INFO/DTUN_HCID(2132): bdaddr=01:00:00:7F:B5:B3 03-21 03:10:52.070: INFO/DTUN_CLNT(2132): Client calling DTUN_METHOD_DM_GET_REMOTE_SERVICE_CHANNEL (id 4) 03-21 03:10:52.070: INFO/(2106): DTUN_ReceiveCtrlMsg: [DTUN] Received message [BTLIF_DTUN_METHOD_CALL] 4354 03-21 03:10:52.070: INFO/(2106): handle_method_call: handle_method_call :: received DTUN_METHOD_DM_GET_REMOTE_SERVICE_CHANNEL (id 4), len 134 03-21 03:10:52.075: ERROR/BTLD(2106): ****************search UUID = 1101*********** 03-21 03:10:52.075: INFO//system/bin/btld(2103): btapp_dm_GetRemoteServiceChannel() 03-21 03:10:52.120: DEBUG/BluetoothService(1914): updateDeviceServiceChannelCache(01:00:00:7F:B5:B3) 03-21 03:10:52.120: DEBUG/BluetoothEventLoop(1914): ClassValue: null for remote device: 01:00:00:7F:B5:B3 is null 03-21 03:10:52.120: INFO/BluetoothEventLoop.cpp(1914): event_filter: Received signal org.bluez.Adapter:PropertyChanged from /org/bluez/2132/hci0 03-21 03:10:52.305: WARN/BTLD(2106): bta_dm_check_av:0 03-21 03:10:56.395: DEBUG/WifiService(1914): ACTION_BATTERY_CHANGED pluggedType: 2 03-21 03:10:57.440: WARN/BTLD(2106): SDP - Rcvd conn cnf with error: 0x4 CID 0x43 03-21 03:10:57.440: INFO/BTL-IFS(2106): send_ctrl_msg: [BTL_IFS CTRL] send BTLIF_DTUN_SIGNAL_EVT (CTRL) 13 pbytes (hdl 10) 03-21 03:10:57.445: INFO/DTUN_CLNT(2132): dtun-rx signal [DTUN_SIG_DM_RMT_SERVICE_CHANNEL] (id 42) len 15 03-21 03:10:57.445: INFO/DTUN_HCID(2132): dtun_dm_sig_rmt_service_channel: success=1, service=00000000 03-21 03:10:57.445: ERROR/DTUN_HCID(2132): discovery unsuccessful! package de.phil_dev.android.BT; import java.io.BufferedInputStream; import java.io.IOException; import java.io.InputStream; import java.io.OutputStream; import java.util.UUID; import android.app.Activity; import android.bluetooth.BluetoothAdapter; import android.bluetooth.BluetoothClass; import android.bluetooth.BluetoothDevice; import android.bluetooth.BluetoothServerSocket; import android.bluetooth.BluetoothSocket; import android.content.Intent; import android.os.Bundle; import android.util.Log; import android.widget.Toast; public class ThinBTClient extends Activity { private static final String TAG = "THINBTCLIENT"; private static final boolean D = true; private BluetoothAdapter mBluetoothAdapter = null; private BluetoothSocket btSocket = null; private BufferedInputStream inStream = null; private BluetoothServerSocket myServerSocket; private ConnectThread myConnection; private ServerThread myServer; // Well known SPP UUID (will *probably* map to // RFCOMM channel 1 (default) if not in use); // see comments in onResume(). private static final UUID MY_UUID = UUID .fromString("00001101-0000-1000-8000-00805F9B34FB"); // .fromString("94f39d29-7d6d-437d-973b-fba39e49d4ee"); // ==> hardcode your slaves MAC address here <== // PC // private static String address = "00:09:DD:50:86:A0"; // GPS private static String address = "00:0B:0D:8E:D4:33"; /** Called when the activity is first created. */ @Override public void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.main); if (D) Log.e(TAG, "+++ ON CREATE +++"); mBluetoothAdapter = BluetoothAdapter.getDefaultAdapter(); if (mBluetoothAdapter == null) { Toast.makeText(this, "Bluetooth is not available.", Toast.LENGTH_LONG).show(); finish(); return; } if (!mBluetoothAdapter.isEnabled()) { Toast.makeText(this, "Please enable your BT and re-run this program.", Toast.LENGTH_LONG).show(); finish(); return; } if (D) Log.e(TAG, "+++ DONE IN ON CREATE, GOT LOCAL BT ADAPTER +++"); } @Override public void onStart() { super.onStart(); if (D) Log.e(TAG, "++ ON START ++"); } @Override public void onResume() { super.onResume(); if (D) { Log.e(TAG, "+ ON RESUME +"); Log.e(TAG, "+ ABOUT TO ATTEMPT CLIENT CONNECT +"); } // Make the phone discoverable // When this returns, it will 'know' about the server, // via it's MAC address. // mBluetoothAdapter.startDiscovery(); BluetoothDevice device = mBluetoothAdapter.getRemoteDevice(address); Log.e(TAG, device.getName() + " connected"); // myServer = new ServerThread(); // myServer.start(); myConnection = new ConnectThread(device); myConnection.start(); } @Override public void onPause() { super.onPause(); if (D) Log.e(TAG, "- ON PAUSE -"); try { btSocket.close(); } catch (IOException e2) { Log.e(TAG, "ON PAUSE: Unable to close socket.", e2); } } @Override public void onStop() { super.onStop(); if (D) Log.e(TAG, "-- ON STOP --"); } @Override public void onDestroy() { super.onDestroy(); if (D) Log.e(TAG, "--- ON DESTROY ---"); } private class ServerThread extends Thread { private final BluetoothServerSocket myServSocket; public ServerThread() { BluetoothServerSocket tmp = null; // create listening socket try { tmp = mBluetoothAdapter .listenUsingRfcommWithServiceRecord( "myServer", MY_UUID); } catch (IOException e) { Log.e(TAG, "Server establishing failed"); } myServSocket = tmp; } public void run() { Log.e(TAG, "Beginn waiting for connection"); BluetoothSocket connectSocket = null; InputStream inStream = null; byte[] buffer = new byte[1024]; int bytes; while (true) { try { connectSocket = myServSocket.accept(); } catch (IOException e) { Log.e(TAG, "Connection failed"); break; } Log.e(TAG, "ALL THE WAY AROUND"); try { connectSocket = connectSocket.getRemoteDevice() .createRfcommSocketToServiceRecord(MY_UUID); connectSocket.connect(); } catch (IOException e1) { Log.e(TAG, "DIDNT WORK"); } // handle Connection try { inStream = connectSocket.getInputStream(); while (true) { try { bytes = inStream.read(buffer); Log.e(TAG, "Received: " + buffer.toString()); } catch (IOException e3) { Log.e(TAG, "disconnected"); break; } } } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); break; } } } void cancel() { } } private class ConnectThread extends Thread { private final BluetoothSocket mySocket; private final BluetoothDevice myDevice; public ConnectThread(BluetoothDevice device) { myDevice = device; BluetoothSocket tmp = null; try { tmp = device.createRfcommSocketToServiceRecord(MY_UUID); } catch (IOException e) { Log.e(TAG, "CONNECTION IN THREAD DIDNT WORK"); } mySocket = tmp; } public void run() { Log.e(TAG, "STARTING TO CONNECT THE SOCKET"); setName("My Connection Thread"); InputStream inStream = null; boolean run = false; //mBluetoothAdapter.cancelDiscovery(); try { mySocket.connect(); run = true; } catch (IOException e) { run = false; Log.e(TAG, this.getName() + ": CONN DIDNT WORK, Try closing socket"); try { mySocket.close(); } catch (IOException e1) { Log.e(TAG, this.getName() + ": COULD CLOSE SOCKET", e1); this.destroy(); } } synchronized (ThinBTClient.this) { myConnection = null; } byte[] buffer = new byte[1024]; int bytes; // handle Connection try { inStream = mySocket.getInputStream(); while (run) { try { bytes = inStream.read(buffer); Log.e(TAG, "Received: " + buffer.toString()); } catch (IOException e3) { Log.e(TAG, "disconnected"); } } } catch (IOException e) { // TODO Auto-generated catch block e.printStackTrace(); } // starting connected thread (handling there in and output } public void cancel() { try { mySocket.close(); } catch (IOException e) { Log.e(TAG, this.getName() + " SOCKET NOT CLOSED"); } } } }

  Read the article

• Returning a list from a function in Python

  - by Jasper

  Hi, I'm creating a game for my sister, and I want a function to return a list variable, so I can pass it to another variable. The relevant code is as follows: def startNewGame(): while 1: #Introduction: print print """Hello, You will now be guided through the setup process. There are 7 steps to this. You can cancel setup at any time by typing 'cancelSetup' Thankyou""" #Step 1 (Name): print print """Step 1 of 7: Type in a name for your PotatoHead: """ inputPHName = raw_input('|Enter Name:|') if inputPHName == 'cancelSetup': sys.exit() #Step 2 (Gender): print print """Step 2 of 7: Choose the gender of your PotatoHead: input either 'm' or 'f' """ inputPHGender = raw_input('|Enter Gender:|') if inputPHGender == 'cancelSetup': sys.exit() #Step 3 (Colour): print print """Step 3 of 7: Choose the colour your PotatoHead will be: Only Red, Blue, Green and Yellow are currently supported """ inputPHColour = raw_input('|Enter Colour:|') if inputPHColour == 'cancelSetup': sys.exit() #Step 4 (Favourite Thing): print print """Step 4 of 7: Type your PotatoHead's favourite thing: """ inputPHFavThing = raw_input('|Enter Favourite Thing:|') if inputPHFavThing == 'cancelSetup': sys.exit() # Step 5 (First Toy): print print """Step 5 of 7: Choose a first toy for your PotatoHead: """ inputPHFirstToy = raw_input('|Enter First Toy:|') if inputPHFirstToy == 'cancelSetup': sys.exit() #Step 6 (Check stats): while 1: print print """Step 6 of 7: Check the following details to make sure that they are correct: """ print print """Name:\t\t\t""" + inputPHName + """ Gender:\t\t\t""" + inputPHGender + """ Colour:\t\t\t""" + inputPHColour + """ Favourite Thing:\t""" + inputPHFavThing + """ First Toy:\t\t""" + inputPHFirstToy + """ """ print print "Enter 'y' or 'n'" inputMCheckStats = raw_input('|Is this information correct?|') if inputMCheckStats == 'cancelSetup': sys.exit() elif inputMCheckStats == 'y': break elif inputMCheckStats == 'n': print "Re-enter info: ..." print break else: "The value you entered was incorrect, please re-enter your choice" if inputMCheckStats == 'y': break #Step 7 (Define variables for the creation of the PotatoHead): MFCreatePH = [] print print """Step 7 of 7: Your PotatoHead will now be created... Creating variables... """ MFCreatePH = [inputPHName, inputPHGender, inputPHColour, inputPHFavThing, inputPHFirstToy] time.sleep(1) print "inputPHName" print time.sleep(1) print "inputPHFirstToy" print return MFCreatePH print "Your PotatoHead varibles have been successfully created!" Then it is passed to another function that was imported from another module from potatohead import * ... welcomeMessage() MCreatePH = startGame() myPotatoHead = PotatoHead(MCreatePH) the code for the PotatoHead object is in the potatohead.py module which was imported above, and is as follows: class PotatoHead: #Initialise the PotatoHead object: def __init__(self, data): self.data = data #Takes the data from the start new game function - see main.py #Defines the PotatoHead starting attributes: self.name = data[0] self.gender = data[1] self.colour = data[2] self.favouriteThing = data[3] self.firstToy = data[4] self.age = '0.0' self.education = [self.eduScience, self.eduEnglish, self.eduMaths] = '0.0', '0.0', '0.0' self.fitness = '0.0' self.happiness = '10.0' self.health = '10.0' self.hunger = '0.0' self.tiredness = 'Not in this version' self.toys = [] self.toys.append(self.firstToy) self.time = '0' #Sets data lists for saving, loading and general use: self.phData = (self.name, self.gender, self.colour, self.favouriteThing, self.firstToy) self.phAdvData = (self.name, self.gender, self.colour, self.favouriteThing, self.firstToy, self.age, self.education, self.fitness, self.happiness, self.health, self.hunger, self.tiredness, self.toys) However, when I run the program this error appears: Traceback (most recent call last): File "/Users/Jasper/Documents/Programming/Potato Head Game/Current/main.py", line 158, in <module> myPotatoHead = PotatoHead(MCreatePH) File "/Users/Jasper/Documents/Programming/Potato Head Game/Current/potatohead.py", line 15, in __init__ self.name = data[0] TypeError: 'NoneType' object is unsubscriptable What am i doing wrong? -----EDIT----- The program finishes as so: Step 7 of 7: Your PotatoHead will now be created... Creating variables... inputPHName inputPHFirstToy Then it goes to the Tracback -----EDIT2----- This is the EXACT code I'm running in its entirety: #+--------------------------------------+# #| main.py |# #| A main module for the Potato Head |# #| Game to pull the other modules |# #| together and control through user |# #| input |# #| Author: |# #| Date Created / Modified: |# #| 3/2/10 | 20/2/10 |# #+--------------------------------------+# Tested: No #Import the required modules: import time import random import sys from potatohead import * from toy import * #Start the Game: def welcomeMessage(): print "----- START NEW GAME -----------------------" print "==Print Welcome Message==" print "loading... \t loading... \t loading..." time.sleep(1) print "loading..." time.sleep(1) print "LOADED..." print; print; print; print """Hello, Welcome to the Potato Head Game. In this game you can create a Potato Head, and look after it, like a Virtual Pet. This game is constantly being updated and expanded. Please look out for updates. """ #Choose whether to start a new game or load a previously saved game: def startGame(): while 1: print "--------------------" print """ Choose an option: New_Game or Load_Game """ startGameInput = raw_input('>>> >') if startGameInput == 'New_Game': startNewGame() break elif startGameInput == 'Load_Game': print "This function is not yet supported" print "Try Again" print else: print "You must have mistyped the command: Type either 'New_Game' or 'Load_Game'" print #Set the new game up: def startNewGame(): while 1: #Introduction: print print """Hello, You will now be guided through the setup process. There are 7 steps to this. You can cancel setup at any time by typing 'cancelSetup' Thankyou""" #Step 1 (Name): print print """Step 1 of 7: Type in a name for your PotatoHead: """ inputPHName = raw_input('|Enter Name:|') if inputPHName == 'cancelSetup': sys.exit() #Step 2 (Gender): print print """Step 2 of 7: Choose the gender of your PotatoHead: input either 'm' or 'f' """ inputPHGender = raw_input('|Enter Gender:|') if inputPHGender == 'cancelSetup': sys.exit() #Step 3 (Colour): print print """Step 3 of 7: Choose the colour your PotatoHead will be: Only Red, Blue, Green and Yellow are currently supported """ inputPHColour = raw_input('|Enter Colour:|') if inputPHColour == 'cancelSetup': sys.exit() #Step 4 (Favourite Thing): print print """Step 4 of 7: Type your PotatoHead's favourite thing: """ inputPHFavThing = raw_input('|Enter Favourite Thing:|') if inputPHFavThing == 'cancelSetup': sys.exit() # Step 5 (First Toy): print print """Step 5 of 7: Choose a first toy for your PotatoHead: """ inputPHFirstToy = raw_input('|Enter First Toy:|') if inputPHFirstToy == 'cancelSetup': sys.exit() #Step 6 (Check stats): while 1: print print """Step 6 of 7: Check the following details to make sure that they are correct: """ print print """Name:\t\t\t""" + inputPHName + """ Gender:\t\t\t""" + inputPHGender + """ Colour:\t\t\t""" + inputPHColour + """ Favourite Thing:\t""" + inputPHFavThing + """ First Toy:\t\t""" + inputPHFirstToy + """ """ print print "Enter 'y' or 'n'" inputMCheckStats = raw_input('|Is this information correct?|') if inputMCheckStats == 'cancelSetup': sys.exit() elif inputMCheckStats == 'y': break elif inputMCheckStats == 'n': print "Re-enter info: ..." print break else: "The value you entered was incorrect, please re-enter your choice" if inputMCheckStats == 'y': break #Step 7 (Define variables for the creation of the PotatoHead): MFCreatePH = [] print print """Step 7 of 7: Your PotatoHead will now be created... Creating variables... """ MFCreatePH = [inputPHName, inputPHGender, inputPHColour, inputPHFavThing, inputPHFirstToy] time.sleep(1) print "inputPHName" print time.sleep(1) print "inputPHFirstToy" print return MFCreatePH print "Your PotatoHead varibles have been successfully created!" #Run Program: welcomeMessage() MCreatePH = startGame() myPotatoHead = PotatoHead(MCreatePH) The potatohead.py module is as follows: #+--------------------------------------+# #| potatohead.py |# #| A module for the Potato Head Game |# #| Author: |# #| Date Created / Modified: |# #| 24/1/10 | 24/1/10 |# #+--------------------------------------+# Tested: Yes (24/1/10) #Create the PotatoHead class: class PotatoHead: #Initialise the PotatoHead object: def __init__(self, data): self.data = data #Takes the data from the start new game function - see main.py #Defines the PotatoHead starting attributes: self.name = data[0] self.gender = data[1] self.colour = data[2] self.favouriteThing = data[3] self.firstToy = data[4] self.age = '0.0' self.education = [self.eduScience, self.eduEnglish, self.eduMaths] = '0.0', '0.0', '0.0' self.fitness = '0.0' self.happiness = '10.0' self.health = '10.0' self.hunger = '0.0' self.tiredness = 'Not in this version' self.toys = [] self.toys.append(self.firstToy) self.time = '0' #Sets data lists for saving, loading and general use: self.phData = (self.name, self.gender, self.colour, self.favouriteThing, self.firstToy) self.phAdvData = (self.name, self.gender, self.colour, self.favouriteThing, self.firstToy, self.age, self.education, self.fitness, self.happiness, self.health, self.hunger, self.tiredness, self.toys) #Define the phStats variable, enabling easy display of PotatoHead attributes: def phDefStats(self): self.phStats = """Your Potato Head's Stats are as follows: ---------------------------------------- Name: \t\t""" + self.name + """ Gender: \t\t""" + self.gender + """ Colour: \t\t""" + self.colour + """ Favourite Thing: \t""" + self.favouriteThing + """ First Toy: \t""" + self.firstToy + """ Age: \t\t""" + self.age + """ Education: \t""" + str(float(self.eduScience) + float(self.eduEnglish) + float(self.eduMaths)) + """ -> Science: \t""" + self.eduScience + """ -> English: \t""" + self.eduEnglish + """ -> Maths: \t""" + self.eduMaths + """ Fitness: \t""" + self.fitness + """ Happiness: \t""" + self.happiness + """ Health: \t""" + self.health + """ Hunger: \t""" + self.hunger + """ Tiredness: \t""" + self.tiredness + """ Toys: \t\t""" + str(self.toys) + """ Time: \t\t""" + self.time + """ """ #Change the PotatoHead's favourite thing: def phChangeFavouriteThing(self, newFavouriteThing): self.favouriteThing = newFavouriteThing phChangeFavouriteThingMsg = "Your Potato Head's favourite thing is " + self.favouriteThing + "." #"Feed" the Potato Head i.e. Reduce the 'self.hunger' attribute's value: def phFeed(self): if float(self.hunger) >=3.0: self.hunger = str(float(self.hunger) - 3.0) elif float(self.hunger) < 3.0: self.hunger = '0.0' self.time = str(int(self.time) + 1) #Pass time #"Exercise" the Potato Head if between the ages of 5 and 25: def phExercise(self): if float(self.age) < 5.1 or float(self.age) > 25.1: print "This Potato Head is either too young or too old for this activity!" else: if float(self.fitness) <= 8.0: self.fitness = str(float(self.fitness) + 2.0) elif float(self.fitness) > 8.0: self.fitness = '10.0' self.time = str(int(self.time) + 1) #Pass time #"Teach" the Potato Head: def phTeach(self, subject): if subject == 'Science': if float(self.eduScience) <= 9.0: self.eduScience = str(float(self.eduScience) + 1.0) elif float(self.eduScience) > 9.0 and float(self.eduScience) < 10.0: self.eduScience = '10.0' elif float(self.eduScience) == 10.0: print "Your Potato Head has gained the highest level of qualifications in this subject! It cannot learn any more!" elif subject == 'English': if float(self.eduEnglish) <= 9.0: self.eduEnglish = str(float(self.eduEnglish) + 1.0) elif float(self.eduEnglish) > 9.0 and float(self.eduEnglish) < 10.0: self.eduEnglish = '10.0' elif float(self.eduEnglish) == 10.0: print "Your Potato Head has gained the highest level of qualifications in this subject! It cannot learn any more!" elif subject == 'Maths': if float(self.eduMaths) <= 9.0: self.eduMaths = str(float(self.eduMaths) + 1.0) elif float(self.eduMaths) > 9.0 and float(self.eduMaths) < 10.0: self.eduMaths = '10.0' elif float(self.eduMaths) == 10.0: print "Your Potato Head has gained the highest level of qualifications in this subject! It cannot learn any more!" else: print "That subject is not an option..." print "Please choose either Science, English or Maths" self.time = str(int(self.time) + 1) #Pass time #Increase Health: def phGoToDoctor(self): self.health = '10.0' self.time = str(int(self.time) + 1) #Pass time #Sleep: Age, change stats: #(Time Passes) def phSleep(self): self.time = '0' #Resets time for next 'day' (can do more things next day) #Increase hunger: if float(self.hunger) <= 5.0: self.hunger = str(float(self.hunger) + 5.0) elif float(self.hunger) > 5.0: self.hunger = '10.0' #Lower Fitness: if float(self.fitness) >= 0.5: self.fitness = str(float(self.fitness) - 0.5) elif float(self.fitness) < 0.5: self.fitness = '0.0' #Lower Health: if float(self.health) >= 0.5: self.health = str(float(self.health) - 0.5) elif float(self.health) < 0.5: self.health = '0.0' #Lower Happiness: if float(self.happiness) >= 2.0: self.happiness = str(float(self.happiness) - 2.0) elif float(self.happiness) < 2.0: self.happiness = '0.0' #Increase the Potato Head's age: self.age = str(float(self.age) + 0.1) The game is still under development - There may be parts of modules that aren't complete, but I don't think they're causing the problem

  Read the article

• How do I send automated e-mails from Drupal using Messaging and Notifications?

  - by Adrian

  I am working on a Notifications plugin, and after starting to write my notes down about how to do this, decided to just post them here. Please feel free to come make modifications and changes. Eventually I hope to post this on the Drupal handbook as well. Thanks. --Adrian Sending automated e-mails from Drupal using Messaging and Notifications To implement a notifications plugin, you must implement the following functions: Use hook_messaging, hook_token_list and hook_token_values to create the messages that will be sent. Use hook_notifications to create the subscription types Add code to fire events (eg in hook_nodeapi) Add all UI elements to allow users to subscribe/unsubscribe Understanding Messaging The Messaging module is used to compose messages that can be delivered using various formats, such as simple mail, HTML mail, Twitter updates, etc. These formats are called "send methods." The backend details do not concern us here; what is important are the following concepts: TOKENS: tokens are provided by the "tokens" module. They allow you to write keywords in square brackets, [like-this], that can be replaced by any arbitrary value. Note: the token groups you create must match the keys you add to the $events-objects[$key] array. MESSAGE KEYS: A key is a part of a message, such as the greetings line. Keys can be different for each send method. For example, a plaintext mail's greeting might be "Hi, [user]," while an HTML greeing might be "Hi, [user]," and Twitter's might just be "[user-firstname]: ". Keys can have any arbitrary name. Keys are very simple and only have a machine-readable name and a user-readable description, the latter of which is only seen by admins. MESSAGE GROUPS: A group is a bunch of keys that often, but not always, might be used together to make up a complete message. For example, a generic group might include keys for a greeting, body, closing and footer. Groups can also be "subclassed" by selecting a "fallback" group that will supply any keys that are missing. Groups are also associated with modules; I'm not sure what these are used for. Understanding Notifications The Notifications module revolves around the following concepts: SUBSCRIPTIONS: Notifications plugins may define one or more types of subscriptions. For example, notifications_content defines subscriptions for: Threads (users are notified whenever a node or its comments change) Content types (users are notified whenever a node of a certain type is created or is changed) Users (users are notified whenever another user is changed) Subscriptions refer to both the user who's subscribed, how often they wish to be notified, the send method (for Messaging) and what's being subscribed to. This last part is defined in two steps. Firstly, a plugin defines several "subscription fields" (through a hook_notifications op of the same name), and secondly, "subscription types" (also an op) defines which fields apply to each type of subscription. For example, notifications_content defines the fields "nid," "author" and "type," and the subscriptions "thread" (nid), "nodetype" (type), "author" (author) and "typeauthor" (type and author), the latter referring to something like "any STORY by JOE." Fields are used to link events to subscriptions; an event must match all fields of a subscription (for all normal subscriptions) to be delivered to the recipient. The $subscriptions object is defined in subsequent sections. Notifications prefers that you don't create these objects yourself, preferring you to call the notifications_get_link() function to create a link that users may click on, but you can also use notifications_save_subscription and notifications_delete_subscription to do it yourself. EVENTS: An event is something that users may be notified about. Plugins create the $event object then call notifications_event($event). This either sends out notifications immediately, queues them to send out later, or both. Events include the type of thing that's changed (eg 'node', 'user'), the ID of the thing that's changed (eg $node-nid, $user-uid) and what's happened to it (eg 'create'). These are, respectively, $event-type, $event-oid (object ID) and $event-action. Warning: notifications_content_nodeapi also adds a $event-node field, referring to the node itself and not just $event-oid = $node-nid. This is not used anywhere in the core notifications module; however, when the $event is passed back to the 'query' op (see below), we assume the node is still present. Events do not refer to the user they will be referred to; instead, Notifications makes the connection between subscriptions and events, using the subscriptions' fields. MATCHING EVENTS TO SUBSCRIPTIONS: An event matches a subscription if it has the same type as the event (eg "node") and if the event matches all the correct fields. This second step is determined by the "query" hook op, which is called with the $event object as a parameter. The query op is responsible for giving Notifications a value for all the fields defined by the plugin. For example, notifications_content defines the 'nid', 'type' and 'author' fields, so its query op looks like this (ignore the case where $event_or_user = 'user' for now): $event_or_user = $arg0; $event_type = $arg1; $event_or_object = $arg2; if ($event_or_user == 'event' && $event_type == 'node' && ($node = $event_or_object->node) || $event_or_user == 'user' && $event_type == 'node' && ($node = $event_or_object)) { $query[]['fields'] = array( 'nid' => $node->nid, 'type' => $node->type, 'author' => $node->uid, ); return $query; After extracting the $node from the $event, we set $query[]['fields'] to a dictionary defining, for this event, all the fields defined by the module. As you can tell from the presence of the $query object, there's way more you can do with this op, but they are not covered here. DIGESTING AND DEDUPING: Understanding the relationship between Messaging and Notifications Usually, the name of a message group doesn't matter, but when being used with Notifications, the names must follow very strict patterns. Firstly, they must start with the name "notifications," and then are followed by either "event" or "digest," depending on whether the message group is being used to represent either a single event or a group of events. For 'events,' the third part of the name is the "type," which we get from Notification's $event-type (eg: notifications_content uses 'node'). The last part of the name is the operation being performed, which comes from Notification's $event-action. For example: notifications-event-node-comment might refer to the message group used when someone comments on a node notifications-event-user-update to a user who's updated their profile Hyphens cannot appear anywhere other than to separate the parts of these words. For 'digest' messages, the third and fourth part of the name come from hook_notification's "event types" callback, specifically this line: $types[] = array( 'type' => 'node', 'action' => 'insert', ... 'digest' => array('node', 'type'), ); $types[] = array( 'type' => 'node', 'action' => 'update', ... 'digest' => array('node', 'nid'), ); In this case, the first event type (node insertion) will be digested with the notifications-digest-node-type message template providing the header and footer, likely saying something like "the following [type] was created." The second event type (node update) will be digested with the notifications-digest-node-nid message template. Data Structure and Callback Reference $event The $event object has the following members: $event-type: The type of event. Must match the type in hook_notification::"event types". {notifications_event} $event-action: The action the event describes. Most events are sorted by [$event-type][$event-action]. {notifications_event}. $event-object[$object_type]: All objects relevant to the event. For example, $event-object['node'] might be the node that the event describes. $object_type can come from the 'event types' hook (see below). The main purpose appears to be to be passed to token_replace_multiple as the second parameter. $event-object[$event-type] is assumed to exist in the short digest processing functions, but this doesn't appear to be used anywhere. Not saved in the database; loaded by hook_notifications::"event load" $event-oid: apparently unused. The id of the primary object relevant to this event (eg the node's nid). $event-module: apparently unused $event-params[$key]: Mainly a place for plugins to save random data. The main module will serialize the contents of this array but does not use it in any way. However, notifications_ui appears to do something weird with it, possibly by using subscriptions' fields as keys into this array. I'm not sure why though. hook_notifications op 'subscription types': returns an array of subscription types provided by the plugin, in the form $key = array(...) with the following members: event_type: this subscription can only match events whose $event-type has this value. Stored in the database as notifications.event_type for every individual subscription. Apparently, this can be overiden in code but I wouldn't try it (see notifications_save_subscription). fields: an unkeyed array of fields that must be matched by an event (in addition to the event_type) for it to match this subscription. Each element of this array must be a key of the array returned by op 'subscription fields' which in turn must be used by op 'query' to actually perform the matching. title: user-readable title for their subscriptions page (eg the 'type' column in user/%uid/notifications/subscriptions) description: a user-readable description. page callback: used to add a supplementary page at user/%uid/notifications/blah. This and the following are used by notifications_ui as a part of hook_menu_alter. Appears to be partially deprecated. user page: user/%uid/notifications/blah. op 'event types': returns an array of event types, with each event type being an array with the following members: type: this will match $event-type action: this will match $event-action digest: an array with two ordered (non-keyed) elements, "type" and "field." 'type' is used as an index into $event-objects. 'field' is also used to group events like so: $event-objects[$type]-$field. For example, 'field' might be 'nid' - if the object is a node, the digest lines will be grouped by node ID. Finally, both are used to find the correct Messaging template; see discussion above. description: used on the admin "Notifications-Events" page name: unused, use Messaging instead line: deprecated, use Messaging instead Other Stuff This is an example of the main query that inserts an event into the queue: INSERT INTO {notifications_queue} (uid, destination, sid, module, eid, send_interval, send_method, cron, created, conditions) SELECT DISTINCT s.uid, s.destination, s.sid, s.module, %d, // event ID s.send_interval, s.send_method, s.cron, %d, // time of the event s.conditions FROM {notifications} s INNER JOIN {notifications_fields} f ON s.sid = f.sid WHERE (s.status = 1) AND (s.event_type = '%s') // subscription type AND (s.send_interval >= 0) AND (s.uid <> %d) AND ( (f.field = '%s' AND f.intval IN (%d)) // everything from 'query' op OR (f.field = '%s' AND f.intval = %d) OR (f.field = '%s' AND f.value = '%s') OR (f.field = '%s' AND f.intval = %d)) GROUP BY s.uid, s.destination, s.sid, s.module, s.send_interval, s.send_method, s.cron, s.conditions HAVING s.conditions = count(f.sid)

  Read the article

• Exporting a non public Type through public API

  - by sachin

  I am trying to follow Trees tutorial at: http://cslibrary.stanford.edu/110/BinaryTrees.html Here is the code I have written so far: package trees.bst; import java.util.ArrayList; import java.util.List; import java.util.StringTokenizer; /** * * @author sachin */ public class BinarySearchTree { Node root = null; class Node { Node left = null; Node right = null; int data = 0; public Node(int data) { this.left = null; this.right = null; this.data = data; } } public void insert(int data) { root = insert(data, root); } public boolean lookup(int data) { return lookup(data, root); } public void buildTree(int numNodes) { for (int i = 0; i < numNodes; i++) { int num = (int) (Math.random() * 10); System.out.println("Inserting number:" + num); insert(num); } } public int size() { return size(root); } public int maxDepth() { return maxDepth(root); } public int minValue() { return minValue(root); } public int maxValue() { return maxValue(root); } public void printTree() { //inorder traversal System.out.println("inorder traversal:"); printTree(root); System.out.println("\n--------------"); } public void printPostorder() { //inorder traversal System.out.println("printPostorder traversal:"); printPostorder(root); System.out.println("\n--------------"); } public int buildTreeFromOutputString(String op) { root = null; int i = 0; StringTokenizer st = new StringTokenizer(op); while (st.hasMoreTokens()) { String stNum = st.nextToken(); int num = Integer.parseInt(stNum); System.out.println("buildTreeFromOutputString: Inserting number:" + num); insert(num); i++; } return i; } public boolean hasPathSum(int pathsum) { return hasPathSum(pathsum, root); } public void mirror() { mirror(root); } public void doubleTree() { doubleTree(root); } public boolean sameTree(BinarySearchTree bst) { //is this tree same as another given tree? return sameTree(this.root, bst.getRoot()); } public void printPaths() { if (root == null) { System.out.println("print path sum: tree is empty"); } List pathSoFar = new ArrayList(); printPaths(root, pathSoFar); } ///-------------------------------------------Public helper functions public Node getRoot() { return root; } //Exporting a non public Type through public API ///-------------------------------------------Helper Functions private boolean isLeaf(Node node) { if (node == null) { return false; } if (node.left == null && node.right == null) { return true; } return false; } ///----------------------------------------------------------- private boolean sameTree(Node n1, Node n2) { if ((n1 == null && n2 == null)) { return true; } else { if ((n1 == null || n2 == null)) { return false; } else { if ((n1.data == n2.data)) { return (sameTree(n1.left, n2.left) && sameTree(n1.right, n2.right)); } } } return false; } private void doubleTree(Node node) { //create a copy //bypass the copy to continue looping if (node == null) { return; } Node copyNode = new Node(node.data); Node temp = node.left; node.left = copyNode; copyNode.left = temp; doubleTree(copyNode.left); doubleTree(node.right); } private void mirror(Node node) { if (node == null) { return; } Node temp = node.left; node.left = node.right; node.right = temp; mirror(node.left); mirror(node.right); } private void printPaths(Node node, List pathSoFar) { if (node == null) { return; } pathSoFar.add(node.data); if (isLeaf(node)) { System.out.println("path in tree:" + pathSoFar); pathSoFar.remove(pathSoFar.lastIndexOf(node.data)); //only the current node, a node.data may be duplicated return; } else { printPaths(node.left, pathSoFar); printPaths(node.right, pathSoFar); } } private boolean hasPathSum(int pathsum, Node node) { if (node == null) { return false; } int val = pathsum - node.data; boolean ret = false; if (val == 0 && isLeaf(node)) { ret = true; } else if (val == 0 && !isLeaf(node)) { ret = false; } else if (val != 0 && isLeaf(node)) { ret = false; } else if (val != 0 && !isLeaf(node)) { //recurse further ret = hasPathSum(val, node.left) || hasPathSum(val, node.right); } return ret; } private void printPostorder(Node node) { //inorder traversal if (node == null) { return; } printPostorder(node.left); printPostorder(node.right); System.out.print(" " + node.data); } private void printTree(Node node) { //inorder traversal if (node == null) { return; } printTree(node.left); System.out.print(" " + node.data); printTree(node.right); } private int minValue(Node node) { if (node == null) { //error case: this is not supported return -1; } if (node.left == null) { return node.data; } else { return minValue(node.left); } } private int maxValue(Node node) { if (node == null) { //error case: this is not supported return -1; } if (node.right == null) { return node.data; } else { return maxValue(node.right); } } private int maxDepth(Node node) { if (node == null || (node.left == null && node.right == null)) { return 0; } int ldepth = 1 + maxDepth(node.left); int rdepth = 1 + maxDepth(node.right); if (ldepth > rdepth) { return ldepth; } else { return rdepth; } } private int size(Node node) { if (node == null) { return 0; } return 1 + size(node.left) + size(node.right); } private Node insert(int data, Node node) { if (node == null) { node = new Node(data); } else if (data <= node.data) { node.left = insert(data, node.left); } else { node.right = insert(data, node.right); } //control should never reach here; return node; } private boolean lookup(int data, Node node) { if (node == null) { return false; } if (node.data == data) { return true; } if (data < node.data) { return lookup(data, node.left); } else { return lookup(data, node.right); } } public static void main(String[] args) { BinarySearchTree bst = new BinarySearchTree(); int treesize = 5; bst.buildTree(treesize); //treesize = bst.buildTreeFromOutputString("4 4 4 6 7"); treesize = bst.buildTreeFromOutputString("3 4 6 3 6"); //treesize = bst.buildTreeFromOutputString("10"); for (int i = 0; i < treesize; i++) { System.out.println("Searching:" + i + " found:" + bst.lookup(i)); } System.out.println("tree size:" + bst.size()); System.out.println("maxDepth :" + bst.maxDepth()); System.out.println("minvalue :" + bst.minValue()); System.out.println("maxvalue :" + bst.maxValue()); bst.printTree(); bst.printPostorder(); int pathSum = 10; System.out.println("hasPathSum " + pathSum + ":" + bst.hasPathSum(pathSum)); pathSum = 6; System.out.println("hasPathSum " + pathSum + ":" + bst.hasPathSum(pathSum)); pathSum = 19; System.out.println("hasPathSum " + pathSum + ":" + bst.hasPathSum(pathSum)); bst.printPaths(); bst.printTree(); //bst.mirror(); System.out.println("Tree after mirror function:"); bst.printTree(); //bst.doubleTree(); System.out.println("Tree after double function:"); bst.printTree(); System.out.println("tree size:" + bst.size()); System.out.println("Same tree:" + bst.sameTree(bst)); BinarySearchTree bst2 = new BinarySearchTree(); bst2.buildTree(treesize); treesize = bst2.buildTreeFromOutputString("3 4 6 3 6"); bst2.printTree(); System.out.println("Same tree:" + bst.sameTree(bst2)); System.out.println("---"); } } Now the problem is that netbeans shows Warning: Exporting a non public Type through public API for function getRoot(). I write this function to get root of tree to be used in sameTree() function, to help comparison of "this" with given tree. Perhaps this is a OOP design issue... How should I restructure the above code that I do not get this warning and what is the concept I am missing here?

  Read the article

• Can't build pyxpcom on OS X 10.6

  - by Gj

  I've been following these instructions at https://developer.mozilla.org/en/Building_PyXPCOM but getting this: $ make make export make[2]: Nothing to be done for `export'. make[4]: Nothing to be done for `export'. make[4]: Nothing to be done for `export'. /opt/local/bin/python2.5 ../../../src/config/nsinstall.py -L /usr/local/pyxpcom/build/xpcom/src -m 644 ../../../src/xpcom/src/PyXPCOM.h ../../dist/include make[3]: Nothing to be done for `export'. /opt/local/bin/python2.5 ../../../../src/config/nsinstall.py -D ../../../dist/idl /opt/local/bin/python2.5 ../../../../src/config/nsinstall.py -D ../../../dist/idl make[4]: *** No rule to make target `_xpidlgen/py_test_component.h', needed by `export'. Stop. make[3]: *** [export] Error 2 make[2]: *** [export] Error 2 make[1]: *** [export] Error 2 make: *** [default] Error 2 Any ideas? An interesting anomaly is that despite me setting the PYTHON env variable to Python 2.6, the configure and make both seem to go after the 2.5... Thanks for any advice! PS here's the configure output: $ ../src/configure --with-libxul-sdk=/Users/me/xulrunner-sdk/ loading cache ./config.cache checking host system type... i386-apple-darwin10.3.0 checking target system type... i386-apple-darwin10.3.0 checking build system type... i386-apple-darwin10.3.0 checking for mawk... (cached) gawk checking for perl5... (cached) /opt/local/bin/perl5 checking for gcc... (cached) gcc checking whether the C compiler (gcc ) works... yes checking whether the C compiler (gcc ) is a cross-compiler... no checking whether we are using GNU C... (cached) yes checking whether gcc accepts -g... (cached) yes checking for c++... (cached) c++ checking whether the C++ compiler (c++ ) works... yes checking whether the C++ compiler (c++ ) is a cross-compiler... no checking whether we are using GNU C++... (cached) yes checking whether c++ accepts -g... (cached) yes checking for ranlib... (cached) ranlib checking for as... (cached) /usr/bin/as checking for ar... (cached) ar checking for ld... (cached) ld checking for strip... (cached) strip checking for windres... no checking whether gcc and cc understand -c and -o together... (cached) yes checking how to run the C preprocessor... (cached) gcc -E checking how to run the C++ preprocessor... (cached) c++ -E checking for a BSD compatible install... (cached) /usr/bin/install -c checking whether ln -s works... (cached) yes checking for minimum required perl version >= 5.006... 5.008009 checking for full perl installation... yes checking for /opt/local/bin/python... (cached) /opt/local/bin/python2.5 checking for doxygen... (cached) : checking for whoami... (cached) /usr/bin/whoami checking for autoconf... (cached) /opt/local/bin/autoconf checking for unzip... (cached) /usr/bin/unzip checking for zip... (cached) /usr/bin/zip checking for makedepend... (cached) /opt/local/bin/makedepend checking for xargs... (cached) /usr/bin/xargs checking for pbbuild... (cached) /usr/bin/xcodebuild checking for sdp... (cached) /usr/bin/sdp checking for gmake... (cached) /opt/local/bin/gmake checking for X... (cached) no checking whether the compiler supports -Wno-invalid-offsetof... yes checking whether ld has archive extraction flags... (cached) no checking that static assertion macros used in autoconf tests work... (cached) yes checking for 64-bit OS... yes checking for minimum required Python version >= 2.4... yes checking for -dead_strip option to ld... yes checking for ANSI C header files... (cached) yes checking for working const... (cached) yes checking for mode_t... (cached) yes checking for off_t... (cached) yes checking for pid_t... (cached) yes checking for size_t... (cached) yes checking for st_blksize in struct stat... (cached) yes checking for siginfo_t... (cached) yes checking for int16_t... (cached) yes checking for int32_t... (cached) yes checking for int64_t... (cached) yes checking for int64... (cached) no checking for uint... (cached) yes checking for uint_t... (cached) no checking for uint16_t... (cached) no checking for uname.domainname... (cached) no checking for uname.__domainname... (cached) no checking for usable char16_t (2 bytes, unsigned)... (cached) no checking for usable wchar_t (2 bytes, unsigned)... (cached) no checking for compiler -fshort-wchar option... (cached) yes checking for visibility(hidden) attribute... (cached) yes checking for visibility(default) attribute... (cached) yes checking for visibility pragma support... (cached) yes checking For gcc visibility bug with class-level attributes (GCC bug 26905)... (cached) yes checking For x86_64 gcc visibility bug with builtins (GCC bug 20297)... (cached) no checking for dirent.h that defines DIR... (cached) yes checking for opendir in -ldir... (cached) no checking for sys/byteorder.h... (cached) no checking for compat.h... (cached) no checking for getopt.h... (cached) yes checking for sys/bitypes.h... (cached) no checking for memory.h... (cached) yes checking for unistd.h... (cached) yes checking for gnu/libc-version.h... (cached) no checking for nl_types.h... (cached) yes checking for malloc.h... (cached) no checking for X11/XKBlib.h... (cached) yes checking for io.h... (cached) no checking for sys/statvfs.h... (cached) yes checking for sys/statfs.h... (cached) no checking for sys/vfs.h... (cached) no checking for sys/mount.h... (cached) yes checking for sys/quota.h... (cached) yes checking for mmintrin.h... (cached) yes checking for new... (cached) yes checking for sys/cdefs.h... (cached) yes checking for gethostbyname_r in -lc_r... (cached) no checking for dladdr... (cached) yes checking for socket in -lsocket... (cached) no checking whether mmap() sees write()s... yes checking whether gcc needs -traditional... (cached) no checking for 8-bit clean memcmp... (cached) yes checking for random... (cached) yes checking for strerror... (cached) yes checking for lchown... (cached) yes checking for fchmod... (cached) yes checking for snprintf... (cached) yes checking for statvfs... (cached) yes checking for memmove... (cached) yes checking for rint... (cached) yes checking for stat64... (cached) yes checking for lstat64... (cached) yes checking for truncate64... (cached) no checking for statvfs64... (cached) no checking for setbuf... (cached) yes checking for isatty... (cached) yes checking for flockfile... (cached) yes checking for getpagesize... (cached) yes checking for localtime_r... (cached) yes checking for strtok_r... (cached) yes checking for wcrtomb... (cached) yes checking for mbrtowc... (cached) yes checking for res_ninit()... (cached) no checking for gnu_get_libc_version()... (cached) no ../src/configure: line 9881: AM_LANGINFO_CODESET: command not found checking for an implementation of va_copy()... (cached) yes checking for an implementation of __va_copy()... (cached) yes checking whether va_lists can be copied by value... (cached) no checking for C++ exceptions flag... (cached) -fno-exceptions checking for gcc 3.0 ABI... (cached) yes checking for C++ "explicit" keyword... (cached) yes checking for C++ "typename" keyword... (cached) yes checking for modern C++ template specialization syntax support... (cached) yes checking whether partial template specialization works... (cached) yes checking whether operators must be re-defined for templates derived from templates... (cached) no checking whether we need to cast a derived template to pass as its base class... (cached) no checking whether the compiler can resolve const ambiguities for templates... (cached) yes checking whether the C++ "using" keyword can change access... (cached) yes checking whether the C++ "using" keyword resolves ambiguity... (cached) yes checking for "std::" namespace... (cached) yes checking whether standard template operator!=() is ambiguous... (cached) unambiguous checking for C++ reinterpret_cast... (cached) yes checking for C++ dynamic_cast to void*... (cached) yes checking whether C++ requires implementation of unused virtual methods... (cached) yes checking for trouble comparing to zero near std::operator!=()... (cached) no checking for LC_MESSAGES... (cached) yes checking for tar archiver... checking for gnutar... (cached) gnutar gnutar checking for wget... checking for wget... (cached) wget wget checking for valid optimization flags... yes checking for gcc -pipe support... yes checking whether compiler supports -Wno-long-long... yes checking whether C compiler supports -fprofile-generate... yes checking for correct temporary object destruction order... yes checking for correct overload resolution with const and templates... no Building Python extensions using python-2.5 from /opt/local/Library/Frameworks/Python.framework/Versions/2.5 creating ./config.status creating config/autoconf.mk creating Makefile creating xpcom/Makefile creating xpcom/src/Makefile creating xpcom/src/loader/Makefile creating xpcom/src/module/Makefile creating xpcom/components/Makefile creating xpcom/test/Makefile creating xpcom/test/test_component/Makefile creating dom/Makefile creating dom/src/Makefile creating dom/test/Makefile creating dom/test/pyxultest/Makefile creating dom/nsdom/Makefile creating dom/nsdom/test/Makefile

  Read the article

• Getting problem in collision detection in Java Game

  - by chetans

  Hi I am developing Spaceship Game in which i am getting problem in collision detection of moving images Game has a spaceship and number of asteroids(obstacles) i want to detect the collision between them How can i do this?`package Game; import java.applet.Applet; import java.awt.Color; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Image; import java.awt.MediaTracker; import java.awt.event.KeyEvent; import java.awt.event.KeyListener; import java.net.MalformedURLException; import java.net.URL; public class ThreadInApplet extends Applet implements KeyListener { private static final long serialVersionUID = 1L; Image[] asteroidImage; Image spaceshipImage; int[] XPosObst,YPosObst; int numberOfObstacles=0,XPosOfSpaceship,YPosOfSpaceship; int spaceButtnCntr=0,noOfObstaclesLevel=20; boolean gameStart=false,collideUp=false,collideDown=false,collideLeft=false,collideRight=false; private Image offScreenImage; private Dimension offScreenSize,d; private Graphics offScreenGraphics; int speedObstacles=1; String spaceshipImagePath="images/spaceship.png",obstacleImagepath="images/asteroid.png"; String buttonToStart="Press Space to start"; public void init() { try { asteroidImage=new Image[noOfObstaclesLevel]; XPosObst=new int[noOfObstaclesLevel]; YPosObst=new int[noOfObstaclesLevel]; XPosOfSpaceship=getWidth()/2-35; YPosOfSpaceship=getHeight()-100; spaceshipImage=getImage(new URL(getCodeBase(),spaceshipImagePath)); for(int i=0;i<noOfObstaclesLevel;i++) { asteroidImage[i]=getImage(new URL(getCodeBase(),obstacleImagepath)); XPosObst[i]=(int) (Math.random()*700); YPosObst[i]=0; } MediaTracker tracker = new MediaTracker (this); for(int i=0;i<noOfObstaclesLevel;i++) { tracker.addImage (asteroidImage[i], 0); } } catch (MalformedURLException e) { e.printStackTrace(); } setBackground(Color.black); addKeyListener(this); } public void paint(Graphics g) { g.setColor(Color.white); if(gameStart==false) { g.drawString(buttonToStart, (getWidth()/2)-60, getHeight()/2); } g.drawString("HEADfitted Solutions Pvt.Ltd.", (getWidth()/2)-80, getHeight()-20); for(int n=0;n<numberOfObstacles;n++) { if(n>0) g.drawImage(asteroidImage[n],XPosObst[n],YPosObst[n],this); } g.drawImage(spaceshipImage,XPosOfSpaceship,YPosOfSpaceship,this); } @SuppressWarnings("deprecation") public void update(Graphics g) { d = size(); if((offScreenImage == null) || (d.width != offScreenSize.width) || (d.height != offScreenSize.height)) { offScreenImage = createImage(d.width, d.height); offScreenSize = d; offScreenGraphics = offScreenImage.getGraphics(); } offScreenGraphics.clearRect(0, 0, d.width, d.height); paint(offScreenGraphics); g.drawImage(offScreenImage, 0, 0, null); } public void keyReleased(KeyEvent arg0){} public void keyTyped(KeyEvent arg0) {} Thread mainThread=new Thread() { synchronized public void run () { try { //System.out.println("in main thread"); if (gameStart==true) { moveObstacles.start(); if(collide()==false) { createObsThread.start(); } } } catch (Exception e) { e.printStackTrace(); } } }; Thread createObsThread=new Thread() { synchronized public void run () { if (spaceButtnCntr==1) { if (collide()==false) { for(int g=0;g<noOfObstaclesLevel;g++) { try { sleep(1000); } catch (InterruptedException e) { e.printStackTrace(); } numberOfObstacles++; } } } } }; Thread moveObstacles=new Thread() // Moving Obstacle images downwards after every 10 ms { synchronized public void run () { while(YPosObst[19]!=600) { if (collide()==false) { //createObsThread.start(); for(int l=0;l } repaint(); try { sleep(10); } catch (InterruptedException e) { e.printStackTrace(); } } } } }; public void keyPressed(KeyEvent e) { if(e.getKeyCode()==32) { gameStart=true; spaceButtnCntr++; if (spaceButtnCntr==1) { mainThread.start(); } } if(gameStart==true) { if(e.getKeyCode()==37 && collideLeft==false)//Spaceship movement left { new Thread () { synchronized public void run () { XPosOfSpaceship-=10; repaint(); } }.start(); } if(e.getKeyCode()==38 && collideUp==false)//Spaceship movement up { new Thread () { synchronized public void run () { YPosOfSpaceship-=10; repaint(); } }.start(); } if(e.getKeyCode()==39 && collideRight==false)//Spaceship movement right { new Thread () { synchronized public void run () { XPosOfSpaceship+=10; repaint(); } }.start(); } if(e.getKeyCode()==40 && collideDown==false)//Spaceship movement down { new Thread () { synchronized public void run () { YPosOfSpaceship+=10; repaint(); } }.start(); } } } /*public boolean collide() { int x0, y0, w0, h0, x2, y2, w2, h2; x0=XPosOfSpaceship; y0=YPosOfSpaceship; h0=spaceshipImage.getHeight(null); w0=spaceshipImage.getWidth(null); for(int i=0;i<20;i++) { x2=XPosObst[i]; y2=YPosObst[i]; h2=asteroidImage[i].getHeight(null); w2=asteroidImage[i].getWidth(null); if ((x0 > (x2 + w2)) || ((x0 + w0) < x2)) return false; System.out.println(x2+" "+y2+" "+h2+" "+w2); if ((y0 > (y2 + h2)) || ((y0 + h0) < y2)) return false; } return true; }*/ public boolean collide() { int x1,y1,x2,y2,x3,y3,x4,y4; //coordinates of obstacles int a1,b1,a2,b2,a3,b3,a4,b4; //coordinates of spaceship a1 =XPosOfSpaceship; b1=YPosOfSpaceship; a2=a1+spaceshipImage.getWidth(this); b2=b1; a3=a1; b3=b1+spaceshipImage.getHeight(this); a4=a2; b4=b3; for(int a=0;a if(x1>=a1 && x1<=a2 && x1<=b3 && x1>=b1) return (true); if(x2>=a1 && x2<=a2 && x2<=b3 && x2>=b1) return(true); //********checking asteroid touch spaceship from up direction******** if(y3==b1 && x4>=a1 && x4<=a2) { collideUp = true; return(true); } if(y3==b1 && x3>=a1 && x3<=a2) { collideUp = true; return(true); } //********checking asteroid touch spaceship from left direction****** if(x2==a1 && y4>=b1 && y4<=b3) { collideLeft=true; return(true); } if(x2==a1 && y2>=b1 && y2<=b3) { collideLeft=true; return(true); } //********checking asteroid touch spaceship from right direction***** if(x1==a2 && y3>=b2 && y3<=b4) { collideRight=true; return(true); } if(x1==a2 && y1>=b2 && y1<=b4) { collideRight=true; return(true); } //********checking asteroid touch spaceship from down direction***** if(y1==b3 && x2>=a3 && x2<=a4) { collideDown=true; return(true); } if(y1==b3 && x1>=a3 && x1<=a4) { collideDown=true; return(true); } else { collideUp=false; collideDown=false; collideLeft=false; collideRight=false; } } return(false); } } `

  Read the article

• Android: NullPointerException error in getting data in database

  - by Gil Viernes Marcelo

  This what happens in the system. 1. Admin login this is in other activity but i will not post it coz it has nothing to do with this (no problem) 2. Register user in system (using database no problem) 3. Click add user button (where existing user who register must display its name in ListView) Problem: When I click adduser to see if the system registered the user, it force close. CurrentUser.java package com.example.istronggyminstructor; import java.util.ArrayList; import android.os.Bundle; import android.app.Activity; import android.content.Context; import android.content.Intent; import android.database.Cursor; import android.view.Gravity; import android.view.LayoutInflater; import android.view.Menu; import android.view.View; import android.view.View.OnClickListener; import android.view.ViewGroup; import android.view.ViewGroup.LayoutParams; import android.view.WindowManager; import android.widget.ArrayAdapter; import android.widget.Button; import android.widget.EditText; import android.widget.FrameLayout; import android.widget.ListView; import android.widget.PopupWindow; import android.widget.TextView; import android.widget.Toast; import java.util.ArrayList; import java.util.List; import java.util.Random; import com.example.istronggyminstructor.registeredUserList.Users; import android.content.ContentValues; import android.database.Cursor; import android.database.SQLException; import android.database.sqlite.SQLiteDatabase; public class CurrentUsers extends Activity { private Button register; private Button adduser; EditText getusertext, getpass, getweight, textdisp; View popupview, popupview2; public static ArrayList<String> ArrayofName = new ArrayList<String>(); protected void onCreate(Bundle savedInstanceState) { super.onCreate(savedInstanceState); setContentView(R.layout.activity_current_users); register = (Button) findViewById(R.id.regbut); adduser = (Button) findViewById(R.id.addbut); register.setOnClickListener(new OnClickListener() { @Override public void onClick(View arg0) { LayoutInflater inflator = (LayoutInflater) getBaseContext() .getSystemService(LAYOUT_INFLATER_SERVICE); popupview = inflator.inflate(R.layout.popup, null); final PopupWindow popupWindow = new PopupWindow(popupview, LayoutParams.WRAP_CONTENT, LayoutParams.WRAP_CONTENT); popupWindow.showAtLocation(popupview, Gravity.CENTER, 0, 0); popupWindow.setFocusable(true); popupWindow.update(); Button dismissbtn = (Button) popupview.findViewById(R.id.close); dismissbtn.setOnClickListener(new OnClickListener() { @Override public void onClick(View arg0) { popupWindow.dismiss(); } }); popupWindow.showAsDropDown(register, 50, -30); } }); //Thread.setDefaultUncaughtExceptionHandler(new forceclose(this)); } public void registerUser(View v) { EditText username = (EditText) popupview.findViewById(R.id.usertext); EditText password = (EditText) popupview .findViewById(R.id.passwordtext); EditText weight = (EditText) popupview.findViewById(R.id.weight); String getUsername = username.getText().toString(); String getPassword = password.getText().toString(); String getWeight = weight.getText().toString(); dataHandler dbHandler = new dataHandler(this, null, null, 1); Users user = new Users(getUsername, getPassword, Integer.parseInt(getWeight)); dbHandler.addUsers(user); Toast.makeText(getApplicationContext(), "Registering...", Toast.LENGTH_SHORT).show(); } public void onClick_addUser(View v) { LayoutInflater inflator = (LayoutInflater) getBaseContext() .getSystemService(LAYOUT_INFLATER_SERVICE); popupview2 = inflator.inflate(R.layout.popup2, null); final PopupWindow popupWindow = new PopupWindow(popupview2, LayoutParams.WRAP_CONTENT, LayoutParams.WRAP_CONTENT); popupWindow.showAtLocation(popupview2, Gravity.CENTER, 0, -10); popupWindow.setFocusable(true); popupWindow.update(); Button dismissbtn = (Button) popupview2.findViewById(R.id.close2); dismissbtn.setOnClickListener(new OnClickListener() { @Override public void onClick(View arg0) { popupWindow.dismiss(); } }); popupWindow.showAsDropDown(register, 50, -30); dataHandler dbHandler = new dataHandler(this, null, null, 1); dbHandler.getAllUsers(); ListView list = (ListView)findViewById(R.layout.popup2); ArrayAdapter<String> adapter = new ArrayAdapter<String>(this, android.R.layout.simple_list_item_1, ArrayofName); list.setAdapter(adapter); } @Override public boolean onCreateOptionsMenu(Menu menu) { getMenuInflater().inflate(R.menu.current_users, menu); return true; } } registeredUserList.java package com.example.istronggyminstructor; public class registeredUserList { public static class Users { private static int _id; private static String _users; private static String _password; private static int _weight; private static String[] _workoutlists; private static int _score; public Users() { } public Users(String username, String password, int weight) { _users = username; _password = password; _weight = weight; } public int getId() { return _id; } public static void setId(int id) { _id = id; } public String getUsers() { return _users; } public static void setUsers(String users) { _users = users; } public String getPassword(){ return _password; } public void setPassword(String password){ _password = password; } public int getWeight(){ return _weight; } public static void setWeight(int weight){ _weight = weight; } public String[] getWorkoutLists(){ return _workoutlists; } public void setWorkoutLists(String[] workoutlists){ _workoutlists = workoutlists; } public int score(){ return _score; } public void score(int score){ _score = score; } } } dataHandler.java package com.example.istronggyminstructor; import java.util.ArrayList; import java.util.List; import com.example.istronggyminstructor.registeredUserList.Users; import android.content.ContentValues; import android.content.Context; import android.database.Cursor; import android.database.sqlite.SQLiteDatabase; import android.database.sqlite.SQLiteDatabase.CursorFactory; import android.database.sqlite.SQLiteOpenHelper; public class dataHandler extends SQLiteOpenHelper { private static final int DATABASE_VERSION = 1; private static final String DATABASE_NAME = "userInfo.db"; public static final String TABLE_USERINFO = "user"; public static final String COLUMN_ID = "_id"; public static final String COLUMN_USERNAME = "username"; public static final String COLUMN_PASSWORD = "password"; public static final String COLUMN_WEIGHT = "weight"; public dataHandler(Context context, String name, CursorFactory factory, int version) { super(context, DATABASE_NAME, factory, DATABASE_VERSION); } @Override public void onCreate(SQLiteDatabase db) { String CREATE_USER_TABLE = "CREATE TABLE " + TABLE_USERINFO + " (" + COLUMN_ID + " INTEGER PRIMARY KEY, " + COLUMN_USERNAME + " TEXT," + COLUMN_PASSWORD + " TEXT, " + COLUMN_WEIGHT + " INTEGER " + ");"; db.execSQL(CREATE_USER_TABLE); } @Override public void onUpgrade(SQLiteDatabase db, int oldVersion, int newVersion) { db.execSQL("DROP TABLE IF EXISTS " + TABLE_USERINFO); onCreate(db); } public void addUsers(Users user) { ContentValues values = new ContentValues(); values.put(COLUMN_USERNAME, user.getUsers()); values.put(COLUMN_PASSWORD, user.getPassword()); values.put(COLUMN_WEIGHT, user.getWeight()); SQLiteDatabase db = this.getWritableDatabase(); db.insert(TABLE_USERINFO, null, values); db.close(); } public Users findUsers(String username) { String query = "Select * FROM " + TABLE_USERINFO + " WHERE " + COLUMN_USERNAME + " = \"" + username + "\""; SQLiteDatabase db = this.getWritableDatabase(); Cursor cursor = db.rawQuery(query, null); Users user = new Users(); if (cursor.moveToFirst()) { cursor.moveToFirst(); Users.setUsers(cursor.getString(1)); //Users.setWeight(Integer.parseInt(cursor.getString(3))); not yet needed cursor.close(); } else { user = null; } db.close(); return user; } public List<Users> getAllUsers(){ List<Users> user = new ArrayList(); String selectQuery = "SELECT * FROM " + TABLE_USERINFO; SQLiteDatabase db = this.getWritableDatabase(); Cursor cursor = db.rawQuery(selectQuery, null); if (cursor.moveToFirst()) { do { Users users = new Users(); users.setUsers(cursor.getString(1)); String name = cursor.getString(1); CurrentUsers.ArrayofName.add(name); // Adding contact to list user.add(users); } while (cursor.moveToNext()); } // return user list return user; } public boolean deleteUsers(String username) { boolean result = false; String query = "Select * FROM " + TABLE_USERINFO + " WHERE " + COLUMN_USERNAME + " = \"" + username + "\""; SQLiteDatabase db = this.getWritableDatabase(); Cursor cursor = db.rawQuery(query, null); Users user = new Users(); if (cursor.moveToFirst()) { Users.setId(Integer.parseInt(cursor.getString(0))); db.delete(TABLE_USERINFO, COLUMN_ID + " = ?", new String[] { String.valueOf(user.getId()) }); cursor.close(); result = true; } db.close(); return result; } } Logcat 08-20 03:23:23.293: E/AndroidRuntime(16363): FATAL EXCEPTION: main 08-20 03:23:23.293: E/AndroidRuntime(16363): java.lang.IllegalStateException: Could not execute method of the activity 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.view.View$1.onClick(View.java:3599) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.view.View.performClick(View.java:4204) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.view.View$PerformClick.run(View.java:17355) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.os.Handler.handleCallback(Handler.java:725) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.os.Handler.dispatchMessage(Handler.java:92) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.os.Looper.loop(Looper.java:137) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.app.ActivityThread.main(ActivityThread.java:5041) 08-20 03:23:23.293: E/AndroidRuntime(16363): at java.lang.reflect.Method.invokeNative(Native Method) 08-20 03:23:23.293: E/AndroidRuntime(16363): at java.lang.reflect.Method.invoke(Method.java:511) 08-20 03:23:23.293: E/AndroidRuntime(16363): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:793) 08-20 03:23:23.293: E/AndroidRuntime(16363): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:560) 08-20 03:23:23.293: E/AndroidRuntime(16363): at dalvik.system.NativeStart.main(Native Method) 08-20 03:23:23.293: E/AndroidRuntime(16363): Caused by: java.lang.reflect.InvocationTargetException 08-20 03:23:23.293: E/AndroidRuntime(16363): at java.lang.reflect.Method.invokeNative(Native Method) 08-20 03:23:23.293: E/AndroidRuntime(16363): at java.lang.reflect.Method.invoke(Method.java:511) 08-20 03:23:23.293: E/AndroidRuntime(16363): at android.view.View$1.onClick(View.java:3594) 08-20 03:23:23.293: E/AndroidRuntime(16363): ... 11 more 08-20 03:23:23.293: E/AndroidRuntime(16363): Caused by: java.lang.NullPointerException 08-20 03:23:23.293: E/AndroidRuntime(16363): at com.example.istronggyminstructor.CurrentUsers.onClick_addUser(CurrentUsers.java:118) 08-20 03:23:23.293: E/AndroidRuntime(16363): ... 14 more

  Read the article

• Cnoverting application to MVC architecture

  - by terence6

  I'm practicing writing MVC applications. I have a Mastermind game, that I would like to rewrite as MVC app. I have divided my code to parts, but instead of working game I'm getting empty Frame and an error in "public void paint( Graphics g )". Error comes from calling this method in my view with null argument. But how to overcome this ? MVC was quite simple with swing but awt and it's paint methods are much more complicated. Code of working app : http://paste.pocoo.org/show/224982/ App divided to MVC : Main : public class Main { public static void main(String[] args){ Model model = new Model(); View view = new View("Mastermind", 400, 590, model); Controller controller = new Controller(model, view); view.setVisible(true); } } Controller : import java.awt.*; import java.awt.event.*; public class Controller implements MouseListener, ActionListener { private Model model; private View view; public Controller(Model m, View v){ model = m; view = v; view.addWindowListener( new WindowAdapter(){ public void windowClosing(WindowEvent e){ System.exit(0); } }); view.addMouseListener(this); } public void actionPerformed( ActionEvent e ) { if(e.getSource() == view.checkAnswer){ if(model.isRowFull){ model.check(); } } } public void mousePressed(MouseEvent e) { Point mouse = new Point(); mouse = e.getPoint(); if (model.isPlaying){ if (mouse.x > 350) { int button = 1 + (int)((mouse.y - 32) / 50); if ((button >= 1) && (button <= 5)){ model.fillHole(button); } } } } public void mouseClicked(MouseEvent e) {} public void mouseReleased(MouseEvent e){} public void mouseEntered(MouseEvent e) {} public void mouseExited(MouseEvent e) {} } View : import java.awt.*; import javax.swing.*; import java.awt.event.*; public class View extends Frame implements ActionListener { Model model; JButton checkAnswer; private JPanel button; static final int HIT_X[] = {270,290,310,290,310}, HIT_Y[] = {506,496,496,516,516}; public View(String name, int w, int h, Model m){ model = m; setTitle( name ); setSize( w,h ); setResizable( false ); this.setLayout(new BorderLayout()); button = new JPanel(); button.setSize( new Dimension(400, 100)); button.setVisible(true); checkAnswer = new JButton("Check"); checkAnswer.addActionListener(this); checkAnswer.setSize( new Dimension(200, 30)); button.add( checkAnswer ); this.add( button, BorderLayout.SOUTH); button.setVisible(true); for ( int i=0; i < model.SCORE; i++ ){ for ( int j = 0; j < model.LINE; j++ ){ model.pins[i][j] = new Pin(20,0); model.pins[i][j].setPosition(j*50+30,510-i*50); model.pins[i+model.SCORE][j] = new Pin(8,0); model.pins[i+model.SCORE][j].setPosition(HIT_X[j],HIT_Y[j]-i*50); } } for ( int i=0; i < model.LINE; i++ ){ model.pins[model.OPTIONS][i] = new Pin( 20, i+2 ); model.pins[model.OPTIONS][i].setPosition( 370,i * 50 + 56); } model.combination(); model.paint(null); } public void actionPerformed( ActionEvent e ) { } } Model: import java.awt.*; public class Model extends Frame{ static final int LINE = 5, SCORE = 10, OPTIONS = 20; Pin pins[][] = new Pin[21][LINE]; int combination[] = new int[LINE]; int curPin = 0; int turn = 1; int repaintPin; boolean isUpdate = true, isPlaying = true, isRowFull = false; public Model(){ } void fillHole(int color) { pins[turn-1][curPin].setColor(color+1); repaintPins( turn ); curPin = (curPin+1) % LINE; if (curPin == 0){ isRowFull = true; } } public void paint( Graphics g ) { g.setColor( new Color(238, 238, 238)); g.fillRect( 0,0,400,590); for ( int i=0; i < pins.length; i++ ) { pins[i][0].paint(g); pins[i][1].paint(g); pins[i][2].paint(g); pins[i][3].paint(g); pins[i][4].paint(g); } } public void update( Graphics g ) { if ( isUpdate ) { paint(g); } else { isUpdate = true; pins[repaintPin-1][0].paint(g); pins[repaintPin-1][1].paint(g); pins[repaintPin-1][2].paint(g); pins[repaintPin-1][3].paint(g); pins[repaintPin-1][4].paint(g); } } void repaintPins( int pin ) { repaintPin = pin; isUpdate = false; repaint(); } void check() { int junkPegs[] = new int[LINE], junkCode[] = new int[LINE]; int pegCount = 0, pico = 0; for ( int i = 0; i < LINE; i++ ) { junkPegs[i] = pins[turn-1][i].getColor(); junkCode[i] = combination[i]; } for ( int i = 0; i < LINE; i++ ){ if (junkPegs[i]==junkCode[i]) { pins[turn+SCORE][pegCount].setColor(1); pegCount++; pico++; junkPegs[i] = 98; junkCode[i] = 99; } } for ( int i = 0; i < LINE; i++ ){ for ( int j = 0; j < LINE; j++ ) if (junkPegs[i]==junkCode[j]) { pins[turn+SCORE][pegCount].setColor(2); pegCount++; junkPegs[i] = 98; junkCode[j] = 99; j = LINE; } } repaintPins( turn+SCORE ); if ( pico == LINE ){ isPlaying = false; } else if ( turn >= 10 ){ isPlaying = false; } else{ curPin = 0; isRowFull = false; turn++; } } void combination() { for ( int i = 0; i < LINE; i++ ){ combination[i] = 1 + (int)(Math.random()*5); System.out.print(i+","); } } } class Pin{ private int color, X, Y, radius; private static final Color COLORS[] = { Color.black, Color.white, Color.red, Color.yellow, Color.green, Color.blue, new Color(7, 254, 250)}; public Pin(){ X = 0; Y = 0; radius = 0; color = 0; } public Pin( int r,int c ){ X = 0; Y = 0; radius = r; color = c; } public void paint( Graphics g ){ int x = X-radius; int y = Y-radius; if (color > 0){ g.setColor( COLORS[color]); g.fillOval( x,y,2*radius,2*radius ); } else{ g.setColor( new Color(238, 238, 238) ); g.drawOval( x,y,2*radius-1,2*radius-1 ); } g.setColor( Color.black ); g.drawOval( x,y,2*radius,2*radius ); } public void setPosition( int x,int y ){ this.X = x ; this.Y = y ; } public void setColor( int c ){ color = c; } public int getColor() { return color; } } Any clues on how to overcome this would be great. Have I divided my code improperly ?

  Read the article

• Converting application to MVC architecture

  - by terence6

  I'm practicing writing MVC applications. I have a Mastermind game, that I would like to rewrite as MVC app. I have divided my code to parts, but instead of working game I'm getting empty Frame and an error in "public void paint( Graphics g )". Error comes from calling this method in my view with null argument. But how to overcome this ? MVC was quite simple with swing but awt and it's paint methods are much more complicated. Code of working app : http://paste.pocoo.org/show/224982/ App divided to MVC : Main : public class Main { public static void main(String[] args){ Model model = new Model(); View view = new View("Mastermind", 400, 590, model); Controller controller = new Controller(model, view); view.setVisible(true); } } Controller : import java.awt.*; import java.awt.event.*; public class Controller implements MouseListener, ActionListener { private Model model; private View view; public Controller(Model m, View v){ model = m; view = v; view.addWindowListener( new WindowAdapter(){ public void windowClosing(WindowEvent e){ System.exit(0); } }); view.addMouseListener(this); } public void actionPerformed( ActionEvent e ) { if(e.getSource() == view.checkAnswer){ if(model.isRowFull){ model.check(); } } } public void mousePressed(MouseEvent e) { Point mouse = new Point(); mouse = e.getPoint(); if (model.isPlaying){ if (mouse.x > 350) { int button = 1 + (int)((mouse.y - 32) / 50); if ((button >= 1) && (button <= 5)){ model.fillHole(button); } } } } public void mouseClicked(MouseEvent e) {} public void mouseReleased(MouseEvent e){} public void mouseEntered(MouseEvent e) {} public void mouseExited(MouseEvent e) {} } View : import java.awt.*; import javax.swing.*; import java.awt.event.*; public class View extends Frame implements ActionListener { Model model; JButton checkAnswer; private JPanel button; static final int HIT_X[] = {270,290,310,290,310}, HIT_Y[] = {506,496,496,516,516}; public View(String name, int w, int h, Model m){ model = m; setTitle( name ); setSize( w,h ); setResizable( false ); this.setLayout(new BorderLayout()); button = new JPanel(); button.setSize( new Dimension(400, 100)); button.setVisible(true); checkAnswer = new JButton("Check"); checkAnswer.addActionListener(this); checkAnswer.setSize( new Dimension(200, 30)); button.add( checkAnswer ); this.add( button, BorderLayout.SOUTH); button.setVisible(true); for ( int i=0; i < model.SCORE; i++ ){ for ( int j = 0; j < model.LINE; j++ ){ model.pins[i][j] = new Pin(20,0); model.pins[i][j].setPosition(j*50+30,510-i*50); model.pins[i+model.SCORE][j] = new Pin(8,0); model.pins[i+model.SCORE][j].setPosition(HIT_X[j],HIT_Y[j]-i*50); } } for ( int i=0; i < model.LINE; i++ ){ model.pins[model.OPTIONS][i] = new Pin( 20, i+2 ); model.pins[model.OPTIONS][i].setPosition( 370,i * 50 + 56); } model.combination(); model.paint(null); } public void actionPerformed( ActionEvent e ) { } } Model: import java.awt.*; public class Model extends Frame{ static final int LINE = 5, SCORE = 10, OPTIONS = 20; Pin pins[][] = new Pin[21][LINE]; int combination[] = new int[LINE]; int curPin = 0; int turn = 1; int repaintPin; boolean isUpdate = true, isPlaying = true, isRowFull = false; public Model(){ } void fillHole(int color) { pins[turn-1][curPin].setColor(color+1); repaintPins( turn ); curPin = (curPin+1) % LINE; if (curPin == 0){ isRowFull = true; } } public void paint( Graphics g ) { g.setColor( new Color(238, 238, 238)); g.fillRect( 0,0,400,590); for ( int i=0; i < pins.length; i++ ) { pins[i][0].paint(g); pins[i][1].paint(g); pins[i][2].paint(g); pins[i][3].paint(g); pins[i][4].paint(g); } } public void update( Graphics g ) { if ( isUpdate ) { paint(g); } else { isUpdate = true; pins[repaintPin-1][0].paint(g); pins[repaintPin-1][1].paint(g); pins[repaintPin-1][2].paint(g); pins[repaintPin-1][3].paint(g); pins[repaintPin-1][4].paint(g); } } void repaintPins( int pin ) { repaintPin = pin; isUpdate = false; repaint(); } void check() { int junkPegs[] = new int[LINE], junkCode[] = new int[LINE]; int pegCount = 0, pico = 0; for ( int i = 0; i < LINE; i++ ) { junkPegs[i] = pins[turn-1][i].getColor(); junkCode[i] = combination[i]; } for ( int i = 0; i < LINE; i++ ){ if (junkPegs[i]==junkCode[i]) { pins[turn+SCORE][pegCount].setColor(1); pegCount++; pico++; junkPegs[i] = 98; junkCode[i] = 99; } } for ( int i = 0; i < LINE; i++ ){ for ( int j = 0; j < LINE; j++ ) if (junkPegs[i]==junkCode[j]) { pins[turn+SCORE][pegCount].setColor(2); pegCount++; junkPegs[i] = 98; junkCode[j] = 99; j = LINE; } } repaintPins( turn+SCORE ); if ( pico == LINE ){ isPlaying = false; } else if ( turn >= 10 ){ isPlaying = false; } else{ curPin = 0; isRowFull = false; turn++; } } void combination() { for ( int i = 0; i < LINE; i++ ){ combination[i] = 1 + (int)(Math.random()*5); System.out.print(i+","); } } } class Pin{ private int color, X, Y, radius; private static final Color COLORS[] = { Color.black, Color.white, Color.red, Color.yellow, Color.green, Color.blue, new Color(7, 254, 250)}; public Pin(){ X = 0; Y = 0; radius = 0; color = 0; } public Pin( int r,int c ){ X = 0; Y = 0; radius = r; color = c; } public void paint( Graphics g ){ int x = X-radius; int y = Y-radius; if (color > 0){ g.setColor( COLORS[color]); g.fillOval( x,y,2*radius,2*radius ); } else{ g.setColor( new Color(238, 238, 238) ); g.drawOval( x,y,2*radius-1,2*radius-1 ); } g.setColor( Color.black ); g.drawOval( x,y,2*radius,2*radius ); } public void setPosition( int x,int y ){ this.X = x ; this.Y = y ; } public void setColor( int c ){ color = c; } public int getColor() { return color; } } Any clues on how to overcome this would be great. Have I divided my code improperly ?

  Read the article

• Getting problem in threading in JAVA

  - by chetans

  In this program i want to stop GenerateImage & MovingImage Thread both... And i want to start those threads from begining. Can u send me the solution? Here is the code........ package Game; import java.applet.Applet; import java.awt.Color; import java.awt.Dimension; import java.awt.Graphics; import java.awt.Image; import java.awt.MediaTracker; import java.awt.event.KeyEvent; import java.awt.event.KeyListener; import java.net.MalformedURLException; import java.net.URL; public class ThreadInApplet extends Applet implements KeyListener { private static final long serialVersionUID = 1L; Image[] asteroidImage; Image spaceshipImage; String levelstr="Easy Level"; int[] XPos,YPos; int number=0,XPosOfSpaceship,YPosOfSpaceship,NoOfObstacles=5,speed=1,level=1,spaceBtnPressdCntr=0; boolean gameStart=false,pauseGame=false,collideUp=false,collideDown=false,collideLeft=false,collideRight=false; private Image offScreenImage; private Dimension offScreenSize; private Graphics offScreenGraphics; Thread GenerateImages,MoveImages; public void init() { try { GenerateImages=new Thread () //thread to create obstacles { synchronized public void run () { for(int g=0;g<NoOfObstacles;g++) { try { sleep(1000); } catch (InterruptedException e) { e.printStackTrace(); } number++; // Temporary counter to count the no of obstacles created } } } ; MoveImages=new Thread () //thread to move obstacles { @SuppressWarnings("deprecation") synchronized public void run () { while(YPos[NoOfObstacles-1]!=600) { pauseGame=false; if(collide()==true) { GenerateImages.suspend(); repaint(); } else GenerateImages.resume(); for(int l=0;l<number;l++) { if(collide()==false) YPos[l]++; else GenerateImages.suspend(); } repaint(); try { sleep(speed); } catch (InterruptedException e) { e.printStackTrace(); } } if(YPos[NoOfObstacles-1]>=600) //level complete state { level++; try { levelUpdation(level); System.out.println("aahe"); } catch (MalformedURLException e) { e.printStackTrace(); } repaint(); } } }; initialPos(); spaceshipImage=getImage(new URL(getCodeBase(),"images/space.png")); for(int i=0;i<NoOfObstacles;i++) { asteroidImage[i]=getImage(new URL(getCodeBase(),"images/asteroid.png")); XPos[i]=(int) (Math.random()*700); YPos[i]=0; } MediaTracker tracker = new MediaTracker (this); for(int i=0;i<NoOfObstacles;i++) { tracker.addImage (asteroidImage[i], 0); } } catch (MalformedURLException e) { e.printStackTrace(); } setBackground(Color.black); addKeyListener(this); } //Sets initial positions of spaceship & obstacle images------------------------------------------------------ public void initialPos() throws MalformedURLException { asteroidImage=new Image[NoOfObstacles]; XPos=new int[NoOfObstacles]; YPos=new int[NoOfObstacles]; XPosOfSpaceship=getWidth()/2-35; YPosOfSpaceship=getHeight()-100; collideUp = false; collideDown=false; collideLeft=false; collideRight=false; } //level finished updations------------------------------------------------------------------------------ @SuppressWarnings("deprecation") public void levelUpdation(int level) throws MalformedURLException { NoOfObstacles=NoOfObstacles+20; speed=speed-3; System.out.println(NoOfObstacles+" "+speed); pauseGame=true; initialPos(); repaint(); } //paint method of graphics to print the messages--------------------------------------------------------- public void paint(Graphics g) { g.setColor(Color.white); if(gameStart==false) { g.drawString("SPACE to start", (getWidth()/2)-15, getHeight()/2); g.drawString(levelstr, (getWidth()/2), getHeight()/2+20); } if(level>1) { if(level==2) levelstr="Medium Level"; else levelstr="High Level"; g.drawString("Level Complete ", (getWidth()/2)-15, getHeight()/2); g.drawString(levelstr, (getWidth()/2), getHeight()/2+20); //g.drawString("SPACE to start", (getWidth()/2)-15, getHeight()/2+40); } for(int n=0;n<number;n++) { if(n>0) g.drawImage(asteroidImage[n],XPos[n],YPos[n],this); } g.drawImage(spaceshipImage,XPosOfSpaceship,YPosOfSpaceship,this); } //update method of graphics to print the messages--------------------------------------------------------- @SuppressWarnings("deprecation") public void update(Graphics g) { Dimension d = size(); if((offScreenImage == null) || (d.width != offScreenSize.width) || (d.height != offScreenSize.height)) { offScreenImage = createImage(d.width, d.height); offScreenSize = d; offScreenGraphics = offScreenImage.getGraphics(); } offScreenGraphics.clearRect(0, 0, d.width, d.height); paint(offScreenGraphics); g.drawImage(offScreenImage, 0, 0, null); } public void keyReleased(KeyEvent arg0){} public void keyTyped(KeyEvent arg0) {} //---------------------Key pressed event to start game & to move the spaceship-------------------------------------- public void keyPressed(KeyEvent e) { if(e.getKeyCode()==32) { spaceBtnPressdCntr++; if(spaceBtnPressdCntr==1) { gameStart=true; GenerateImages.start(); MoveImages.start(); } } if(gameStart==true) { if(e.getKeyCode()==37) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideLeft == true) { GenerateImages.suspend(); } else { if(XPosOfSpaceship>0) XPosOfSpaceship--; } } repaint(); } }.start(); } if(e.getKeyCode()==38) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideUp == true) { GenerateImages.suspend(); } else { if(YPosOfSpaceship>10) YPosOfSpaceship--; } } repaint(); } }.start(); } if(e.getKeyCode()==39) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideRight == true) { GenerateImages.suspend(); } else { if(XPosOfSpaceship<750) XPosOfSpaceship++; } } repaint(); } }.start(); } if(e.getKeyCode()==40) { new Thread () { @SuppressWarnings("deprecation") synchronized public void run () { for(int cnt1=1;cnt1<=10;cnt1++) { if(collide()==true && collideDown == true) { GenerateImages.suspend(); } else { if(YPosOfSpaceship<550) YPosOfSpaceship++; } } repaint(); } }.start(); } } } //------------------------------Collision checking between Spaceship & obstacles------------------------------ public boolean collide() { int x1,y1,x2,y2,x3,y3,x4,y4; //coordinates of obstacles int a1,b1,a2,b2,a3,b3,a4,b4; //coordinates of spaceship a1 =XPosOfSpaceship; b1=YPosOfSpaceship; a2=a1+spaceshipImage.getWidth(this); b2=b1; a3=a1; b3=b1+spaceshipImage.getHeight(this); a4=a2; b4=b3; for(int a=0;a<number;a++) { x1 =XPos[a]; y1=YPos[a]; x2=x1+asteroidImage[a].getWidth(this); y2=y1; x3=x1; y3=y1+asteroidImage[a].getHeight(this); x4=x2; y4=y3; /********checking asteroid touch spaceship from up direction********/ if(y3==b1 && x4>=a1 && x4<=a2) { collideUp = true; collideDown=false; collideLeft=false; collideRight=false; return(true); } if(y3==b1 && x3>=a1 && x3<=a2) { collideUp = true; collideDown=false; collideLeft=false; collideRight=false; return(true); } /********checking asteroid touch spaceship from left direction******/ if(x2==a1 && y4>=b1 && y4<=b3) { collideLeft=true; collideUp = false; collideDown=false; collideRight=false; return(true); } if(x2==a1 && y2>=b1 && y2<=b3) { collideLeft=true; collideUp = false; collideDown=false; collideRight=false; return(true); } /********checking asteroid touch spaceship from right direction*****/ if(x1==a2 && y3>=b2 && y3<=b4) { collideRight=true; collideLeft=false; collideUp = false; collideDown=false; return(true); } if(x1==a2 && y1>=b2 && y1<=b4) { collideRight=true; collideLeft=false; collideUp = false; collideDown=false; return(true); } /********checking asteroid touch spaceship from down direction*****/ if(y1==b3 && x2>=a3 && x2<=a4) { collideDown=true; collideRight=false; collideLeft=false; collideUp = false; return(true); } if(y1==b3 && x1>=a3 && x1<=a4) { collideDown=true; collideRight=false; collideLeft=false; collideUp = false; return(true); } } return(false); } }

  Read the article

• Process is killed without a (obvious) reason and program stops working

  - by Krzysiek Gurniak

  Here's what my program is supposed to do: create 4 child processes: process 0 is reading 1 byte at a time from STDIN, then writing it into FIFO process 1 is reading this 1 byte from fifo and write its value as HEX into shared memory process 2 is reading HEX value from shared memory and writing it into pipe finally process 3 is reading from pipe and writing into STDOUT (in my case: terminal) I can't change communication channels. FIFO, then shared memory, then pipes are the only option. My problem: Program stops at random moments when some file is directed into stdin (for example:./program < /dev/urandom). Sometimes after writing 5 HEX values, sometimes after 100. Weird thing is that when it is working and in another terminal I write "pstree -c" there is 1 main process with 4 children processes (which is what I want), but when I write "pstree -c" after it stopped writing (but still runs) there are only 3 child processes. For some reason 1 is gone even though they all have while(1) in them.. I think I might have problem with synchronization here, but I am unable to spot it (I've tried for many hours). Here's the code: #include <unistd.h> #include <fcntl.h> #include <stdio.h> #include <string.h> #include <stdlib.h> #include <sys/shm.h> #include <sys/sem.h> #include <sys/types.h> #include <sys/wait.h> #include <sys/stat.h> #include <string.h> #include <signal.h> #define BUFSIZE 1 #define R 0 #define W 1 // processes ID pid_t p0, p1, p2, p3; // FIFO variables int fifo_fd; unsigned char bufor[BUFSIZE] = {}; unsigned char bufor1[BUFSIZE] = {}; // Shared memory variables key_t key; int shmid; char * tab; // zmienne do pipes int file_des[2]; char bufor_pipe[BUFSIZE*30] = {}; void proces0() { ssize_t n; while(1) { fifo_fd = open("/tmp/fifo",O_WRONLY); if(fifo_fd == -1) { perror("blad przy otwieraniu kolejki FIFO w p0\n"); exit(1); } n = read(STDIN_FILENO, bufor, BUFSIZE); if(n<0) { perror("read error w p0\n"); exit(1); } if(n > 0) { if(write(fifo_fd, bufor, n) != n) { perror("blad zapisu do kolejki fifo w p0\n"); exit(1); } memset(bufor, 0, n); // czyszczenie bufora } close(fifo_fd); } } void proces1() { ssize_t m, x; char wartosc_hex[30] = {}; while(1) { if(tab[0] == 0) { fifo_fd = open("/tmp/fifo", O_RDONLY); // otwiera plik typu fifo do odczytu if(fifo_fd == -1) { perror("blad przy otwieraniu kolejki FIFO w p1\n"); exit(1); } m = read(fifo_fd, bufor1, BUFSIZE); x = m; if(x < 0) { perror("read error p1\n"); exit(1); } if(x > 0) { // Konwersja na HEX if(bufor1[0] < 16) { if(bufor1[0] == 10) // gdy enter { sprintf(wartosc_hex, "0x0%X\n", bufor1[0]); } else { sprintf(wartosc_hex, "0x0%X ", bufor1[0]); } } else { sprintf(wartosc_hex, "0x%X ", bufor1[0]); } // poczekaj az pamiec bedzie pusta (gotowa do zapisu) strcpy(&tab[0], wartosc_hex); memset(bufor1, 0, sizeof(bufor1)); // czyszczenie bufora memset(wartosc_hex, 0, sizeof(wartosc_hex)); // przygotowanie tablicy na zapis wartosci hex x = 0; } close(fifo_fd); } } } void proces2() { close(file_des[0]); // zablokuj kanal do odczytu while(1) { if(tab[0] != 0) { if(write(file_des[1], tab, strlen(tab)) != strlen(tab)) { perror("blad write w p2"); exit(1); } // wyczysc pamiec dzielona by przyjac kolejny bajt memset(tab, 0, sizeof(tab)); } } } void proces3() { ssize_t n; close(file_des[1]); // zablokuj kanal do zapisu while(1) { if(tab[0] == 0) { if((n = read(file_des[0], bufor_pipe, sizeof(bufor_pipe))) > 0) { if(write(STDOUT_FILENO, bufor_pipe, n) != n) { perror("write error w proces3()"); exit(1); } memset(bufor_pipe, 0, sizeof(bufor_pipe)); } } } } int main(void) { key = 5678; int status; // Tworzenie plikow przechowujacych ID procesow int des_pid[2] = {}; char bufor_proces[50] = {}; mknod("pid0", S_IFREG | 0777, 0); mknod("pid1", S_IFREG | 0777, 0); mknod("pid2", S_IFREG | 0777, 0); mknod("pid3", S_IFREG | 0777, 0); // Tworzenie semaforow key_t klucz; klucz = ftok(".", 'a'); // na podstawie pliku i pojedynczego znaku id wyznacza klucz semafora if(klucz == -1) { perror("blad wyznaczania klucza semafora"); exit(1); } semafor = semget(klucz, 1, IPC_CREAT | 0777); // tworzy na podstawie klucza semafor. 1 - ilosc semaforow if(semafor == -1) { perror("blad przy tworzeniu semafora"); exit(1); } if(semctl(semafor, 0, SETVAL, 0) == -1) // ustawia poczatkowa wartosc semafora (klucz, numer w zbiorze od 0, polecenie, argument 0/1/2) { perror("blad przy ustawianiu wartosci poczatkowej semafora"); exit(1); } // Tworzenie lacza nazwanego FIFO if(access("/tmp/fifo", F_OK) == -1) // sprawdza czy plik istnieje, jesli nie - tworzy go { if(mkfifo("/tmp/fifo", 0777) != 0) { perror("blad tworzenia FIFO w main"); exit(1); } } // Tworzenie pamieci dzielonej // Lista pamieci wspoldzielonych, komenda "ipcs" // usuwanie pamieci wspoldzielonej, komenta "ipcrm -m ID_PAMIECI" shmid = shmget(key, (BUFSIZE*30), 0666 | IPC_CREAT); if(shmid == -1) { perror("shmget"); exit(1); } tab = (char *) shmat(shmid, NULL, 0); if(tab == (char *)(-1)) { perror("shmat"); exit(1); } memset(tab, 0, (BUFSIZE*30)); // Tworzenie lacza nienazwanego pipe if(pipe(file_des) == -1) { perror("pipe"); exit(1); } // Tworzenie procesow potomnych if(!(p0 = fork())) { des_pid[W] = open("pid0", O_WRONLY | O_TRUNC | O_CREAT); // 1 - zapis, 0 - odczyt sprintf(bufor_proces, "Proces0 ma ID: %d\n", getpid()); if(write(des_pid[W], bufor_proces, sizeof(bufor_proces)) != sizeof(bufor_proces)) { perror("blad przy zapisie pid do pliku w p0"); exit(1); } close(des_pid[W]); proces0(); } else if(p0 == -1) { perror("blad przy p0 fork w main"); exit(1); } else { if(!(p1 = fork())) { des_pid[W] = open("pid1", O_WRONLY | O_TRUNC | O_CREAT); // 1 - zapis, 0 - odczyt sprintf(bufor_proces, "Proces1 ma ID: %d\n", getpid()); if(write(des_pid[W], bufor_proces, sizeof(bufor_proces)) != sizeof(bufor_proces)) { perror("blad przy zapisie pid do pliku w p1"); exit(1); } close(des_pid[W]); proces1(); } else if(p1 == -1) { perror("blad przy p1 fork w main"); exit(1); } else { if(!(p2 = fork())) { des_pid[W] = open("pid2", O_WRONLY | O_TRUNC | O_CREAT); // 1 - zapis, 0 - odczyt sprintf(bufor_proces, "Proces2 ma ID: %d\n", getpid()); if(write(des_pid[W], bufor_proces, sizeof(bufor_proces)) != sizeof(bufor_proces)) { perror("blad przy zapisie pid do pliku w p2"); exit(1); } close(des_pid[W]); proces2(); } else if(p2 == -1) { perror("blad przy p2 fork w main"); exit(1); } else { if(!(p3 = fork())) { des_pid[W] = open("pid3", O_WRONLY | O_TRUNC | O_CREAT); // 1 - zapis, 0 - odczyt sprintf(bufor_proces, "Proces3 ma ID: %d\n", getpid()); if(write(des_pid[W], bufor_proces, sizeof(bufor_proces)) != sizeof(bufor_proces)) { perror("blad przy zapisie pid do pliku w p3"); exit(1); } close(des_pid[W]); proces3(); } else if(p3 == -1) { perror("blad przy p3 fork w main"); exit(1); } else { // proces macierzysty waitpid(p0, &status, 0); waitpid(p1, &status, 0); waitpid(p2, &status, 0); waitpid(p3, &status, 0); //wait(NULL); unlink("/tmp/fifo"); shmdt(tab); // odlaczenie pamieci dzielonej shmctl(shmid, IPC_RMID, NULL); // usuwanie pamieci wspoldzielonej printf("\nKONIEC PROGRAMU\n"); } } } } exit(0); }

  Read the article

• SSL / HTTP / No Response to Curl

  - by Alex McHale

  I am trying to send commands to a SOAP service, and getting nothing in reply. The SOAP service is at a completely separate site from either server I am testing with. I have written a dummy script with the SOAP XML embedded. When I run it at my local site, on any of three machines -- OSX, Ubuntu, or CentOS 5.3 -- it completes successfully with a good response. I then sent the script to our public host at Slicehost, where I fail to get the response back from the SOAP service. It accepts the TCP socket and proceeds with the SSL handshake. I do not however receive any valid HTTP response. This is the case whether I use my script or curl on the command line. I have rewritten the script using SOAP4R, Net::HTTP and Curb. All of which work at my local site, none of which work at the Slicehost site. I have tried to assemble the CentOS box as closely to match my Slicehost server as possible. I rebuilt the Slice to be a stock CentOS 5.3 and stock CentOS 5.4 with the same results. When I look at a tcpdump of the bad sessions on Slicehost, I see my script or curl send the XML to the remote server, and nothing comes back. When I look at the tcpdump at my local site, I see the response just fine. I have entirely disabled iptables on the Slice. Does anyone have any ideas what could be causing these results? Please let me know what additional information I can furnish. Thank you! Below is a wire trace of a sample session. The IP that starts with 173 is my server while the IP that starts with 12 is the SOAP server's. No. Time Source Destination Protocol Info 1 0.000000 173.45.x.x 12.36.x.x TCP 36872 > https [SYN] Seq=0 Win=5840 Len=0 MSS=1460 TSV=137633469 TSER=0 WS=6 Frame 1 (74 bytes on wire, 74 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 0, Len: 0 No. Time Source Destination Protocol Info 2 0.040000 12.36.x.x 173.45.x.x TCP https > 36872 [SYN, ACK] Seq=0 Ack=1 Win=8760 Len=0 MSS=1460 Frame 2 (62 bytes on wire, 62 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 0, Ack: 1, Len: 0 No. Time Source Destination Protocol Info 3 0.040000 173.45.x.x 12.36.x.x TCP 36872 > https [ACK] Seq=1 Ack=1 Win=5840 Len=0 Frame 3 (54 bytes on wire, 54 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 1, Ack: 1, Len: 0 No. Time Source Destination Protocol Info 4 0.050000 173.45.x.x 12.36.x.x SSLv2 Client Hello Frame 4 (156 bytes on wire, 156 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 1, Ack: 1, Len: 102 Secure Socket Layer No. Time Source Destination Protocol Info 5 0.130000 12.36.x.x 173.45.x.x TCP [TCP segment of a reassembled PDU] Frame 5 (1434 bytes on wire, 1434 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 1, Ack: 103, Len: 1380 Secure Socket Layer No. Time Source Destination Protocol Info 6 0.130000 173.45.x.x 12.36.x.x TCP 36872 > https [ACK] Seq=103 Ack=1381 Win=8280 Len=0 Frame 6 (54 bytes on wire, 54 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 103, Ack: 1381, Len: 0 No. Time Source Destination Protocol Info 7 0.130000 12.36.x.x 173.45.x.x TLSv1 Server Hello, Certificate, Server Hello Done Frame 7 (1280 bytes on wire, 1280 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 1381, Ack: 103, Len: 1226 [Reassembled TCP Segments (2606 bytes): #5(1380), #7(1226)] Secure Socket Layer No. Time Source Destination Protocol Info 8 0.130000 173.45.x.x 12.36.x.x TCP 36872 > https [ACK] Seq=103 Ack=2607 Win=11040 Len=0 Frame 8 (54 bytes on wire, 54 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 103, Ack: 2607, Len: 0 No. Time Source Destination Protocol Info 9 0.130000 173.45.x.x 12.36.x.x TLSv1 Client Key Exchange, Change Cipher Spec, Encrypted Handshake Message Frame 9 (236 bytes on wire, 236 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 103, Ack: 2607, Len: 182 Secure Socket Layer No. Time Source Destination Protocol Info 10 0.190000 12.36.x.x 173.45.x.x TLSv1 Change Cipher Spec, Encrypted Handshake Message Frame 10 (97 bytes on wire, 97 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 2607, Ack: 285, Len: 43 Secure Socket Layer No. Time Source Destination Protocol Info 11 0.190000 173.45.x.x 12.36.x.x TLSv1 Application Data Frame 11 (347 bytes on wire, 347 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 285, Ack: 2650, Len: 293 Secure Socket Layer No. Time Source Destination Protocol Info 12 0.190000 173.45.x.x 12.36.x.x TCP [TCP segment of a reassembled PDU] Frame 12 (1514 bytes on wire, 1514 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 578, Ack: 2650, Len: 1460 Secure Socket Layer No. Time Source Destination Protocol Info 13 0.450000 12.36.x.x 173.45.x.x TCP https > 36872 [ACK] Seq=2650 Ack=578 Win=64958 Len=0 Frame 13 (54 bytes on wire, 54 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 2650, Ack: 578, Len: 0 No. Time Source Destination Protocol Info 14 0.450000 173.45.x.x 12.36.x.x TCP [TCP segment of a reassembled PDU] Frame 14 (206 bytes on wire, 206 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 2038, Ack: 2650, Len: 152 No. Time Source Destination Protocol Info 15 0.510000 12.36.x.x 173.45.x.x TCP [TCP Dup ACK 13#1] https > 36872 [ACK] Seq=2650 Ack=578 Win=64958 Len=0 Frame 15 (54 bytes on wire, 54 bytes captured) Ethernet II, Src: Dell_fb:49:a1 (00:21:9b:fb:49:a1), Dst: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6) Internet Protocol, Src: 12.36.x.x (12.36.x.x), Dst: 173.45.x.x (173.45.x.x) Transmission Control Protocol, Src Port: https (443), Dst Port: 36872 (36872), Seq: 2650, Ack: 578, Len: 0 No. Time Source Destination Protocol Info 16 0.850000 173.45.x.x 12.36.x.x TCP [TCP Retransmission] [TCP segment of a reassembled PDU] Frame 16 (1514 bytes on wire, 1514 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 578, Ack: 2650, Len: 1460 Secure Socket Layer No. Time Source Destination Protocol Info 17 1.650000 173.45.x.x 12.36.x.x TCP [TCP Retransmission] [TCP segment of a reassembled PDU] Frame 17 (1514 bytes on wire, 1514 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 578, Ack: 2650, Len: 1460 Secure Socket Layer No. Time Source Destination Protocol Info 18 3.250000 173.45.x.x 12.36.x.x TCP [TCP Retransmission] [TCP segment of a reassembled PDU] Frame 18 (1514 bytes on wire, 1514 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 578, Ack: 2650, Len: 1460 Secure Socket Layer No. Time Source Destination Protocol Info 19 6.450000 173.45.x.x 12.36.x.x TCP [TCP Retransmission] [TCP segment of a reassembled PDU] Frame 19 (1514 bytes on wire, 1514 bytes captured) Ethernet II, Src: 40:40:17:3a:f4:e6 (40:40:17:3a:f4:e6), Dst: Dell_fb:49:a1 (00:21:9b:fb:49:a1) Internet Protocol, Src: 173.45.x.x (173.45.x.x), Dst: 12.36.x.x (12.36.x.x) Transmission Control Protocol, Src Port: 36872 (36872), Dst Port: https (443), Seq: 578, Ack: 2650, Len: 1460 Secure Socket Layer

  Read the article

• Linux e1000e (Intel networking driver) problems galore, where do I start?

  - by Evan Carroll

  I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

  Read the article

• Fedora 16 can connect to samba share using smbclient but not in nautilus 3.2.1

  - by Nathan Jones

  I have a machine running Ubuntu 11.10 Server acting as a Samba server to share my home directory. Everything works fine on my Windows 7 machine, but on my Fedora 16 laptop, if I use Nautilus to try to access the share using smb://192.168.0.8/nathan in the location bar, it just has the loading cursor and does nothing. It never shows any errors, nothing. Using smbclient works just fine, but I'd like to get it working in Nautilus. I know that there can be problems with SELinux and Samba, so I created a file called booleans.local that contains samba_enable_home_dirs=1. My smb.conf file looks like this: # For Unix password sync to work on a Debian GNU/Linux system, the following # parameters must be set (thanks to Ian Kahan <<[email protected]> for # sending the correct chat script for the passwd program in Debian Sarge). passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . # This boolean controls whether PAM will be used for password changes # when requested by an SMB client instead of the program listed in # 'passwd program'. The default is 'no'. pam password change = yes # This option controls how unsuccessful authentication attempts are mapped # to anonymous connections map to guest = bad user ########## Domains ########### # Is this machine able to authenticate users. Both PDC and BDC # must have this setting enabled. If you are the BDC you must # change the 'domain master' setting to no # ; domain logons = yes # # The following setting only takes effect if 'domain logons' is set # It specifies the location of the user's profile directory # from the client point of view) # The following required a [profiles] share to be setup on the # samba server (see below) ; logon path = \\%N\profiles\%U # Another common choice is storing the profile in the user's home directory # (this is Samba's default) # logon path = \\%N\%U\profile # The following setting only takes effect if 'domain logons' is set # It specifies the location of a user's home directory (from the client # point of view) ; logon drive = H: # logon home = \\%N\%U # The following setting only takes effect if 'domain logons' is set # It specifies the script to run during logon. The script must be stored # in the [netlogon] share # NOTE: Must be store in 'DOS' file format convention ; logon script = logon.cmd # This allows Unix users to be created on the domain controller via the SAMR # RPC pipe. The example command creates a user account with a disabled Unix # password; please adapt to your needs ; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u # This allows machine accounts to be created on the domain controller via the # SAMR RPC pipe. # The following assumes a "machines" group exists on the system ; add machine script = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u # This allows Unix groups to be created on the domain controller via the SAMR # RPC pipe. ; add group script = /usr/sbin/addgroup --force-badname %g ########## Printing ########## # If you want to automatically load your printer list rather # than setting them up individually then you'll need this # load printers = yes # lpr(ng) printing. You may wish to override the location of the # printcap file ; printing = bsd ; printcap name = /etc/printcap # CUPS printing. See also the cupsaddsmb(8) manpage in the # cupsys-client package. ; printing = cups ; printcap name = cups ############ Misc ############ # Using the following line enables you to customise your configuration # on a per machine basis. The %m gets replaced with the netbios name # of the machine that is connecting ; include = /home/samba/etc/smb.conf.%m # Most people will find that this option gives better performance. # See smb.conf(5) and /usr/share/doc/samba-doc/htmldocs/Samba3-HOWTO/speed.html # for details # You may want to add the following on a Linux system: # SO_RCVBUF=8192 SO_SNDBUF=8192 # socket options = TCP_NODELAY # The following parameter is useful only if you have the linpopup package # installed. The samba maintainer and the linpopup maintainer are # working to ease installation and configuration of linpopup and samba. ; message command = /bin/sh -c '/usr/bin/linpopup "%f" "%m" %s; rm %s' & # Domain Master specifies Samba to be the Domain Master Browser. If this # machine will be configured as a BDC (a secondary logon server), you # must set this to 'no'; otherwise, the default behavior is recommended. # domain master = auto # Some defaults for winbind (make sure you're not using the ranges # for something else.) ; idmap uid = 10000-20000 ; idmap gid = 10000-20000 ; template shell = /bin/bash # The following was the default behaviour in sarge, # but samba upstream reverted the default because it might induce # performance issues in large organizations. # See Debian bug #368251 for some of the consequences of *not* # having this setting and smb.conf(5) for details. ; winbind enum groups = yes ; winbind enum users = yes # Setup usershare options to enable non-root users to share folders # with the net usershare command. # Maximum number of usershare. 0 (default) means that usershare is disabled. ; usershare max shares = 100 # Allow users who've been granted usershare privileges to create # public shares, not just authenticated ones usershare allow guests = yes #======================= Share Definitions ======================= # Un-comment the following (and tweak the other settings below to suit) # to enable the default home directory shares. This will share each # user's home director as \\server\username [homes] comment = Home Directories browseable = yes # By default, the home directories are exported read-only. Change the # next parameter to 'no' if you want to be able to write to them. read only = no # File creation mask is set to 0700 for security reasons. If you want to # create files with group=rw permissions, set next parameter to 0775. ; create mask = 0775 # Directory creation mask is set to 0700 for security reasons. If you want to # create dirs. with group=rw permissions, set next parameter to 0775. ; directory mask = 0775 # By default, \\server\username shares can be connected to by anyone # with access to the samba server. Un-comment the following parameter # to make sure that only "username" can connect to \\server\username # The following parameter makes sure that only "username" can connect # # This might need tweaking when using external authentication schemes valid users = %S # Un-comment the following and create the netlogon directory for Domain Logons # (you need to configure Samba to act as a domain controller too.) ;[netlogon] ; comment = Network Logon Service ; path = /home/samba/netlogon ; guest ok = yes ; read only = yes # Un-comment the following and create the profiles directory to store # users profiles (see the "logon path" option above) # (you need to configure Samba to act as a domain controller too.) # The path below should be writable by all users so that their # profile directory may be created the first time they log on ;[profiles] ; comment = Users profiles ; path = /home/samba/profiles ; guest ok = no ; browseable = no ; create mask = 0600 ; directory mask = 0700 [printers] comment = All Printers browseable = no path = /var/spool/samba printable = yes guest ok = no read only = no create mask = 0700 # Windows clients look for this share name as a source of downloadable # printer drivers [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes read only = yes guest ok = no # Uncomment to allow remote administration of Windows print drivers. # You may need to replace 'lpadmin' with the name of the group your # admin users are members of. # Please note that you also need to set appropriate Unix permissions # to the drivers directory for these users to have write rights in it ; write list = root, @lpadmin # A sample share for sharing your CD-ROM with others. ;[cdrom] ; comment = Samba server's CD-ROM ; read only = yes ; locking = no ; path = /cdrom ; guest ok = yes # The next two parameters show how to auto-mount a CD-ROM when the # cdrom share is accesed. For this to work /etc/fstab must contain # an entry like this: # # /dev/scd0 /cdrom iso9660 defaults,noauto,ro,user 0 0 # # The CD-ROM gets unmounted automatically after the connection to the # # If you don't want to use auto-mounting/unmounting make sure the CD # is mounted on /cdrom # ; preexec = /bin/mount /cdrom ; postexec = /bin/umount /cdrom smbusers: <nathan> = <"nathan"> Any help would be very much appreciated! Thanks!

  Read the article

• Users using Perl script to bypass Squid Proxy

  - by mk22

  The users on our network have been using a perl script to bypass our Squid proxy restrictions. Is there any way we can block this script from working?? #!/usr/bin/perl ######################################################################## # (c) 2008 Indika Bandara Udagedara # [email protected] # http://indikabandara19.blogspot.com # # ---------- # LICENCE # ---------- # This work is protected under GNU GPL # It simply says # " you are hereby granted to do whatever you want with this # except claiming you wrote this." # # # ---------- # README # ---------- # A simple tool to download via http proxies which enforce a download # size limit. Requires curl. # This is NOT a hack. This uses the absolutely legal HTTP/1.1 spec # Tested only for squid-2.6. Only squids will work with this(i think) # Please read the verbose README provided kindly by Rahadian Pratama # if u r on cygwin and think this documentation is not enough :) # # The newest version of pget is available at # http://indikabandara.no-ip.com/~indika/pget # # ---------- # USAGE # ---------- # + Edit below configurations(mainly proxy) # + First run with -i <file> giving a sample file of same type that # you are going to download. Doing this once is enough. # eg. to download '.tar' files first run with # pget -i my.tar ('my.tar' should be a real file) # + Run with # pget -g <URL> # # ######################################################################## ######################################################################## # CONFIGURATIONS - CHANGE THESE FREELY ######################################################################## # *magic* file # pls set absolute path if in cygwin my $_extFile = "./pget.ext" ; # download in chunks of below size my $_chunkSize = 1024*1024; # in Bytes # the proxy that troubles you my $_proxy = "192.168.0.2:3128"; # proxy URL:port my $_proxy_auth = "user:pass"; # proxy user:pass # whereis curl # pls set absolute path if in cygwin my $_curl = "/usr/bin/curl"; ######################################################################## # EDIT BELOW ONLY IF YOU KNOW WHAT YOU ARE DOING ######################################################################## use warnings; my $_version = "0.1.0"; PrintBanner(); if (@ARGV == 0) { PrintHelp(); exit; } PrimaryValidations(); my $val; while(scalar(@ARGV)) { my $arg = shift(@ARGV); if($arg eq '-h') { PrintHelp(); } elsif($arg eq '-i') { $val = shift(@ARGV); if (!defined($val)) { printf("-i option requires a filename\n"); exit; } Init($val); } elsif($arg eq '-g') { $val = shift(@ARGV); if (!defined($val)) { printf("-g option requires a URL\n"); exit; } GetURL($val); } elsif($arg eq '-c') { $val = shift(@ARGV); if (!defined($val)) { printf("-c option requires a URL\n"); exit; } ContinueURL($val); } else { printf ("Unknown option %s\n", $arg); PrintHelp(); } } sub GetURL { my ($URL) = @_; chomp($URL); my $fileName = GetFileName($URL); my %mapExt; my $first; my $readLen; my $ext = GetExt($fileName); ReadMap($_extFile, \%mapExt); if ( exists($mapExt{$ext})) { $first = $mapExt{$ext}; GetFile($URL, $first, $fileName, 0); } else { die "Unknown ext in $fileName. Rerun with -i <fileName>"; } } sub ContinueURL { my ($URL) = @_; chomp($URL); my $fileName = GetFileName($URL); my $fileSize = 0; $fileSize = -s $fileName; printf("Size = %d\n", $fileSize); my $first = -1; if ( $fileSize > 0 ) { $fileSize -= 1; GetFile($URL, $first, $fileName, $fileSize); } else { GetURL($URL); } } sub Init { my ($fileName) = @_; my ($key, $value); my %mapExt; my $ext = GetExt($fileName); if ( $ext eq "") { die "Cannot get ext of \'$fileName\'"; } ReadMap($_extFile, \%mapExt); my $b = GetFirst($fileName); $mapExt{$ext} = $b; WriteMap($_extFile, \%mapExt); print "I handle\n"; while ( ($key, $value) = each(%mapExt) ) { print "\t$key -> $value\n"; } } sub GetExt { my ($name) = @_; my @x = split(/\./, $name); my $ext = ""; if (@x != 1) { $ext = pop @x; } return $ext; } sub ReadMap { my($fileName, $mapRef) = @_; my $f; my @arr; open($f, '<', $fileName) or die "Couldn't open $fileName"; my %map = %{$mapRef}; while (<$f>) { my $line = $_; chomp($line); @arr = split(/[ \t]+/, $line, 2); $mapRef->{ $arr[0]} = $arr[1]; } printf("known ext\n"); while (($key, $value) = each(%$mapRef)) { print("$key, $value\n"); } close($f); } sub WriteMap { my ($fileName, $mapRef) = @_; my $f; my @arr; open($f, '>', $fileName) or die "Couldn't open $fileName"; my ($k, $v); while( ($k, $v) = each(%{$mapRef})) { print $f "$k" . "\t$v\n"; } close($f); } sub PrintHelp { print "usage: -h Print this help -i <filename> Initialize for this filetype -g <URL> Get this URL\n -c <URL> Continue this URL\n" } sub GetFirst { my ($fileName) = @_; my $f; open($f, "<$fileName") or die "Couldn't open $fileName"; my $buffer = ""; my $first = -1; binmode($f); sysread($f, $buffer, 1, 0); close($f); $first = ord($buffer); return $first; } sub GetFirstFromMap { } sub GetFileName { my ($URL) = @_; my @x = split(/\//, $URL); my $fileName = pop @x; return $fileName; } sub GetChunk { my ($URL, $file, $offset, $readLen) = @_; my $end = $offset + $_chunkSize - 1; my $curlCmd = "$_curl -x $_proxy -u $_proxy_auth -r $offset-$end -# \"$URL\""; print "$curlCmd\n"; my $buff = `$curlCmd`; ${$readLen} = syswrite($file, $buff, length($buff)); } sub GetFile { my ($URL, $first, $outFile, $fileSize) = @_; my $readLen = 0; my $start = $fileSize + 1; my $file; open($file, "+>>$outFile") or die "Couldn't open $outFile to write"; if ($fileSize <= 0) { my $uc = pack("C", $first); syswrite ($file, $uc, 1); } do { GetChunk($URL, $file, $start ,\$readLen); $start = $start + $_chunkSize; $fileSize += $readLen; }while ($readLen == $_chunkSize); printf("Downloaded %s(%d bytes).\n", $outFile, $fileSize); close($file); } sub PrintBanner { printf ("pget version %s\n", $_version); printf ("There is absolutely NO WARRANTY for pget.\n"); printf ("Use at your own risk. You have been warned.\n\n"); } sub PrimaryValidations { unless( -e "$_curl") { printf("ERROR:curl is not at %s. Pls install or provide correct path.\n", $_curl); exit; } unless( -e "$_extFile") { printf("extFile is not at %s. Creating one\n", $_extFile); `touch $_extFile`; } if ( $_chunkSize <= 0) { printf ("Invalid chunk size. Using 1Mb as default.\n"); $_chunkSize = 1024*1024; } }

  Read the article

• Building applications with WPF, MVVM and Prism(aka CAG)

  - by skjagini

  In this article I am going to walk through an application using WPF and Prism (aka composite application guidance, CAG) which simulates engaging a taxi (cab).  The rules are simple, the app would have3 screens A login screen to authenticate the user An information screen. A screen to engage the cab and roam around and calculating the total fare Metered Rate of Fare The meter is required to be engaged when a cab is occupied by anyone $3.00 upon entry $0.35 for each additional unit The unit fare is: one-fifth of a mile, when the cab is traveling at 6 miles an hour or more; or 60 seconds when not in motion or traveling at less than 12 miles per hour. Night surcharge of $.50 after 8:00 PM & before 6:00 AM Peak hour Weekday Surcharge of $1.00 Monday - Friday after 4:00 PM & before 8:00 PM New York State Tax Surcharge of $.50 per ride. Example: Friday (2010-10-08) 5:30pm Start at Lexington Ave & E 57th St End at Irving Pl & E 15th St Start = $3.00 Travels 2 miles at less than 6 mph for 15 minutes = $3.50 Travels at more than 12 mph for 5 minutes = $1.75 Peak hour Weekday Surcharge = $1.00 (ride started at 5:30 pm) New York State Tax Surcharge = $0.50 Before we dive into the app, I would like to give brief description about the framework.  If you want to jump on to the source code, scroll all the way to the end of the post. MVVM MVVM pattern is in no way related to the usage of PRISM in your application and should be considered if you are using WPF irrespective of PRISM or not. Lets say you are not familiar with MVVM, your typical UI would involve adding some UI controls like text boxes, a button, double clicking on the button,  generating event handler, calling a method from business layer and updating the user interface, it works most of the time for developing small scale applications. The problem with this approach is that there is some amount of code specific to business logic wrapped in UI specific code which is hard to unit test it, mock it and MVVM helps to solve the exact problem. MVVM stands for Model(M) – View(V) – ViewModel(VM),  based on the interactions with in the three parties it should be called VVMM,  MVVM sounds more like MVC (Model-View-Controller) so the name. Why it should be called VVMM: View – View Model - Model WPF allows to create user interfaces using XAML and MVVM takes it to the next level by allowing complete separation of user interface and business logic. In WPF each view will have a property, DataContext when set to an instance of a class (which happens to be your view model) provides the data the view is interested in, i.e., view interacts with view model and at the same time view model interacts with view through DataContext. Sujith, if view and view model are interacting directly with each other how does MVVM is helping me separation of concerns? Well, the catch is DataContext is of type Object, since it is of type object view doesn’t know exact type of view model allowing views and views models to be loosely coupled. View models aggregate data from models (data access layer, services, etc) and make it available for views through properties, methods etc, i.e., View Models interact with Models. PRISM Prism is provided by Microsoft Patterns and Practices team and it can be downloaded from codeplex for source code,  samples and documentation on msdn.  The name composite implies, to compose user interface from different modules (views) without direct dependencies on each other, again allowing  loosely coupled development. Well Sujith, I can already do that with user controls, why shall I learn another framework?  That’s correct, you can decouple using user controls, but you still have to manage some amount of coupling, like how to do you communicate between the controls, how do you subscribe/unsubscribe, loading/unloading views dynamically. Prism is not a replacement for user controls, provides the following features which greatly help in designing the composite applications. Dependency Injection (DI)/ Inversion of Control (IoC) Modules Regions Event Aggregator  Commands Simply put, MVVM helps building a single view and Prism helps building an application using the views There are other open source alternatives to Prism, like MVVMLight, Cinch, take a look at them as well. Lets dig into the source code.  1. Solution The solution is made of the following projects Framework: Holds the common functionality in building applications using WPF and Prism TaxiClient: Start up project, boot strapping and app styling TaxiCommon: Helps with the business logic TaxiModules: Holds the meat of the application with views and view models TaxiTests: To test the application 2. DI / IoC Dependency Injection (DI) as the name implies refers to injecting dependencies and Inversion of Control (IoC) means the calling code has no direct control on the dependencies, opposite of normal way of programming where dependencies are passed by caller, i.e inversion; aside from some differences in terminology the concept is same in both the cases. The idea behind DI/IoC pattern is to reduce the amount of direct coupling between different components of the application, the higher the dependency the more tightly coupled the application resulting in code which is hard to modify, unit test and mock.  Initializing Dependency Injection through BootStrapper TaxiClient is the starting project of the solution and App (App.xaml)  is the starting class that gets called when you run the application. From the App’s OnStartup method we will invoke BootStrapper.   namespace TaxiClient { /// <summary> /// Interaction logic for App.xaml /// </summary> public partial class App : Application { protected override void OnStartup(StartupEventArgs e) { base.OnStartup(e);   (new BootStrapper()).Run(); } } } BootStrapper is your contact point for initializing the application including dependency injection, creating Shell and other frameworks. We are going to use Unity for DI and there are lot of open source DI frameworks like Spring.Net, StructureMap etc with different feature set  and you can choose a framework based on your preferences. Note that Prism comes with in built support for Unity, for example we are deriving from UnityBootStrapper in our case and for any other DI framework you have to extend the Prism appropriately   namespace TaxiClient { public class BootStrapper: UnityBootstrapper { protected override IModuleCatalog CreateModuleCatalog() { return new ConfigurationModuleCatalog(); } protected override DependencyObject CreateShell() { Framework.FrameworkBootStrapper.Run(Container, Application.Current.Dispatcher);   Shell shell = new Shell(); shell.ResizeMode = ResizeMode.NoResize; shell.Show();   return shell; } } } Lets take a look into  FrameworkBootStrapper to check out how to register with unity container. namespace Framework { public class FrameworkBootStrapper { public static void Run(IUnityContainer container, Dispatcher dispatcher) { UIDispatcher uiDispatcher = new UIDispatcher(dispatcher); container.RegisterInstance<IDispatcherService>(uiDispatcher);   container.RegisterType<IInjectSingleViewService, InjectSingleViewService>( new ContainerControlledLifetimeManager());   . . . } } } In the above code we are registering two components with unity container. You shall observe that we are following two different approaches, RegisterInstance and RegisterType.  With RegisterInstance we are registering an existing instance and the same instance will be returned for every request made for IDispatcherService   and with RegisterType we are requesting unity container to create an instance for us when required, i.e., when I request for an instance for IInjectSingleViewService, unity will create/return an instance of InjectSingleViewService class and with RegisterType we can configure the life time of the instance being created. With ContaienrControllerLifetimeManager, the unity container caches the instance and reuses for any subsequent requests, without recreating a new instance. Lets take a look into FareViewModel.cs and it’s constructor. The constructor takes one parameter IEventAggregator and if you try to find all references in your solution for IEventAggregator, you will not find a single location where an instance of EventAggregator is passed directly to the constructor. The compiler still finds an instance and works fine because Prism is already configured when used with Unity container to return an instance of EventAggregator when requested for IEventAggregator and in this particular case it is called constructor injection. public class FareViewModel:ObservableBase, IDataErrorInfo { ... private IEventAggregator _eventAggregator;   public FareViewModel(IEventAggregator eventAggregator) { _eventAggregator = eventAggregator; InitializePropertyNames(); InitializeModel(); PropertyChanged += OnPropertyChanged; } ... 3. Shell Shells are very similar in operation to Master Pages in asp.net or MDI in Windows Forms. And shells contain regions which display the views, you can have as many regions as you wish in a given view. You can also nest regions. i.e, one region can load a view which in itself may contain other regions. We have to create a shell at the start of the application and are doing it by overriding CreateShell method from BootStrapper From the following Shell.xaml you shall notice that we have two content controls with Region names as ‘MenuRegion’ and ‘MainRegion’.  The idea here is that you can inject any user controls into the regions dynamically, i.e., a Menu User Control for MenuRegion and based on the user action you can load appropriate view into MainRegion.    <Window x:Class="TaxiClient.Shell" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Regions="clr-namespace:Microsoft.Practices.Prism.Regions;assembly=Microsoft.Practices.Prism" Title="Taxi" Height="370" Width="800"> <Grid Margin="2"> <ContentControl Regions:RegionManager.RegionName="MenuRegion" HorizontalAlignment="Stretch" VerticalAlignment="Stretch" HorizontalContentAlignment="Stretch" VerticalContentAlignment="Stretch" />   <ContentControl Grid.Row="1" Regions:RegionManager.RegionName="MainRegion" HorizontalAlignment="Stretch" VerticalAlignment="Stretch" HorizontalContentAlignment="Stretch" VerticalContentAlignment="Stretch" /> <!--<Border Grid.ColumnSpan="2" BorderThickness="2" CornerRadius="3" BorderBrush="LightBlue" />-->   </Grid> </Window> 4. Modules Prism provides the ability to build composite applications and modules play an important role in it. For example if you are building a Mortgage Loan Processor application with 3 components, i.e. customer’s credit history,  existing mortgages, new home/loan information; and consider that the customer’s credit history component involves gathering data about his/her address, background information, job details etc. The idea here using Prism modules is to separate the implementation of these 3 components into their own visual studio projects allowing to build components with no dependency on each other and independently. If we need to add another component to the application, the component can be developed by in house team or some other team in the organization by starting with a new Visual Studio project and adding to the solution at the run time with very little knowledge about the application. Prism modules are defined by implementing the IModule interface and each visual studio project to be considered as a module should implement the IModule interface.  From the BootStrapper.cs you shall observe that we are overriding the method by returning a ConfiguratingModuleCatalog which returns the modules that are registered for the application using the app.config file  and you can also add module using code. Lets take a look into configuration file.   <?xml version="1.0"?> <configuration> <configSections> <section name="modules" type="Microsoft.Practices.Prism.Modularity.ModulesConfigurationSection, Microsoft.Practices.Prism"/> </configSections> <modules> <module assemblyFile="TaxiModules.dll" moduleType="TaxiModules.ModuleInitializer, TaxiModules" moduleName="TaxiModules"/> </modules> </configuration> Here we are adding TaxiModules project to our solution and TaxiModules.ModuleInitializer implements IModule interface   5. Module Mapper With Prism modules you can dynamically add or remove modules from the regions, apart from that Prism also provides API to control adding/removing the views from a region within the same module. Taxi Information Screen: Engage the Taxi Screen: The sample application has two screens, ‘Taxi Information’ and ‘Engage the Taxi’ and they both reside in same module, TaxiModules. ‘Engage the Taxi’ is again made of two user controls, FareView on the left and TotalView on the right. We have created a Shell with two regions, MenuRegion and MainRegion with menu loaded into MenuRegion. We can create a wrapper user control called EngageTheTaxi made of FareView and TotalView and load either TaxiInfo or EngageTheTaxi into MainRegion based on the user action. Though it will work it tightly binds the user controls and for every combination of user controls, we need to create a dummy wrapper control to contain them. Instead we can apply the principles we learned so far from Shell/regions and introduce another template (LeftAndRightRegionView.xaml) made of two regions Region1 (left) and Region2 (right) and load  FareView and TotalView dynamically.  To help with loading of the views dynamically I have introduce an helper an interface, IInjectSingleViewService,  idea suggested by Mike Taulty, a must read blog for .Net developers. using System; using System.Collections.Generic; using System.ComponentModel;   namespace Framework.PresentationUtility.Navigation {   public interface IInjectSingleViewService : INotifyPropertyChanged { IEnumerable<CommandViewDefinition> Commands { get; } IEnumerable<ModuleViewDefinition> Modules { get; }   void RegisterViewForRegion(string commandName, string viewName, string regionName, Type viewType); void ClearViewFromRegion(string viewName, string regionName); void RegisterModule(string moduleName, IList<ModuleMapper> moduleMappers); } } The Interface declares three methods to work with views: RegisterViewForRegion: Registers a view with a particular region. You can register multiple views and their regions under one command.  When this particular command is invoked all the views registered under it will be loaded into their regions. ClearViewFromRegion: To unload a specific view from a region. RegisterModule: The idea is when a command is invoked you can load the UI with set of controls in their default position and based on the user interaction, you can load different contols in to different regions on the fly.  And it is supported ModuleViewDefinition and ModuleMappers as shown below. namespace Framework.PresentationUtility.Navigation { public class ModuleViewDefinition { public string ModuleName { get; set; } public IList<ModuleMapper> ModuleMappers; public ICommand Command { get; set; } }   public class ModuleMapper { public string ViewName { get; set; } public string RegionName { get; set; } public Type ViewType { get; set; } } } 6. Event Aggregator Prism event aggregator enables messaging between components as in Observable pattern, Notifier notifies the Observer which receives notification it is interested in. When it comes to Observable pattern, Observer has to unsubscribes for notifications when it no longer interested in notifications, which allows the Notifier to remove the Observer’s reference from it’s local cache. Though .Net has managed garbage collection it cannot remove inactive the instances referenced by an active instance resulting in memory leak, keeping the Observers in memory as long as Notifier stays in memory.  Developers have to be very careful to unsubscribe when necessary and it often gets overlooked, to overcome these problems Prism Event Aggregator uses weak references to cache the reference (Observer in this case)  and releases the reference (memory) once the instance goes out of scope. Using event aggregator is very simple, declare a generic type of CompositePresenationEvent by inheriting from it. using Microsoft.Practices.Prism.Events; using TaxiCommon.BAO;   namespace TaxiCommon.CompositeEvents { public class TaxiOnMoveEvent:CompositePresentationEvent<TaxiOnMove> { } }   TaxiOnMove.cs includes the properties which we want to exchange between the parties, FareView and TotalView. using System;   namespace TaxiCommon.BAO { public class TaxiOnMove { public TimeSpan MinutesAtTweleveMPH { get; set; } public double MilesAtSixMPH { get; set; } } }   Lets take a look into FareViewodel (Notifier) and how it raises the event.  Here we are raising the event by getting the event through GetEvent<..>() and publishing it with the payload private void OnAddMinutes(object obj) { TaxiOnMove payload = new TaxiOnMove(); if(MilesAtSixMPH != null) payload.MilesAtSixMPH = MilesAtSixMPH.Value; if(MinutesAtTweleveMPH != null) payload.MinutesAtTweleveMPH = new TimeSpan(0,0,MinutesAtTweleveMPH.Value,0);   _eventAggregator.GetEvent<TaxiOnMoveEvent>().Publish(payload); ResetMinutesAndMiles(); } And TotalViewModel(Observer) subscribes to notifications by getting the event through GetEvent<..>() namespace TaxiModules.ViewModels { public class TotalViewModel:ObservableBase { .... private IEventAggregator _eventAggregator;   public TotalViewModel(IEventAggregator eventAggregator) { _eventAggregator = eventAggregator; ... }   private void SubscribeToEvents() { _eventAggregator.GetEvent<TaxiStartedEvent>() .Subscribe(OnTaxiStarted, ThreadOption.UIThread,false,(filter) => true); _eventAggregator.GetEvent<TaxiOnMoveEvent>() .Subscribe(OnTaxiMove, ThreadOption.UIThread, false, (filter) => true); _eventAggregator.GetEvent<TaxiResetEvent>() .Subscribe(OnTaxiReset, ThreadOption.UIThread, false, (filter) => true); }   ... private void OnTaxiMove(TaxiOnMove taxiOnMove) { OnMoveFare fare = new OnMoveFare(taxiOnMove); Fares.Add(fare); SetTotalFare(new []{fare}); }   .... 7. MVVM through example In this section we are going to look into MVVM implementation through example.  I have all the modules declared in a single project, TaxiModules, again it is not necessary to have them into one project. Once the user logs into the application, will be greeted with the ‘Engage the Taxi’ screen which is made of two user controls, FareView.xaml and TotalView.Xaml. As you can see from the solution explorer, each of them have their own code behind files and  ViewModel classes, FareViewMode.cs, TotalViewModel.cs Lets take a look in to the FareView and how it interacts with FareViewModel using MVVM implementation. FareView.xaml acts as a view and FareViewMode.cs is it’s view model. The FareView code behind class   namespace TaxiModules.Views { /// <summary> /// Interaction logic for FareView.xaml /// </summary> public partial class FareView : UserControl { public FareView(FareViewModel viewModel) { InitializeComponent(); this.Loaded += (s, e) => { this.DataContext = viewModel; }; } } } The FareView is bound to FareViewModel through the data context  and you shall observe that DataContext is of type Object, i.e. the FareView doesn’t really know the type of ViewModel (FareViewModel). This helps separation of View and ViewModel as View and ViewModel are independent of each other, you can bind FareView to FareViewModel2 as well and the application compiles just fine. Lets take a look into FareView xaml file  <UserControl x:Class="TaxiModules.Views.FareView" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:Toolkit="clr-namespace:Microsoft.Windows.Controls;assembly=WPFToolkit" xmlns:Commands="clr-namespace:Microsoft.Practices.Prism.Commands;assembly=Microsoft.Practices.Prism"> <Grid Margin="10" > ....   <Border Style="{DynamicResource innerBorder}" Grid.Row="0" Grid.Column="0" Grid.RowSpan="11" Grid.ColumnSpan="2" Panel.ZIndex="1"/>   <Label Grid.Row="0" Content="Engage the Taxi" Style="{DynamicResource innerHeader}"/> <Label Grid.Row="1" Content="Select the State"/> <ComboBox Grid.Row="1" Grid.Column="1" ItemsSource="{Binding States}" Height="auto"> <ComboBox.ItemTemplate> <DataTemplate> <TextBlock Text="{Binding Name}"/> </DataTemplate> </ComboBox.ItemTemplate> <ComboBox.SelectedItem> <Binding Path="SelectedState" Mode="TwoWay"/> </ComboBox.SelectedItem> </ComboBox> <Label Grid.Row="2" Content="Select the Date of Entry"/> <Toolkit:DatePicker Grid.Row="2" Grid.Column="1" SelectedDate="{Binding DateOfEntry, ValidatesOnDataErrors=true}" /> <Label Grid.Row="3" Content="Enter time 24hr format"/> <TextBox Grid.Row="3" Grid.Column="1" Text="{Binding TimeOfEntry, TargetNullValue=''}"/> <Button Grid.Row="4" Grid.Column="1" Content="Start the Meter" Commands:Click.Command="{Binding StartMeterCommand}" />   <Label Grid.Row="5" Content="Run the Taxi" Style="{DynamicResource innerHeader}"/> <Label Grid.Row="6" Content="Number of Miles &lt;@6mph"/> <TextBox Grid.Row="6" Grid.Column="1" Text="{Binding MilesAtSixMPH, TargetNullValue='', ValidatesOnDataErrors=true}"/> <Label Grid.Row="7" Content="Number of Minutes @12mph"/> <TextBox Grid.Row="7" Grid.Column="1" Text="{Binding MinutesAtTweleveMPH, TargetNullValue=''}"/> <Button Grid.Row="8" Grid.Column="1" Content="Add Minutes and Miles " Commands:Click.Command="{Binding AddMinutesCommand}"/> <Label Grid.Row="9" Content="Other Operations" Style="{DynamicResource innerHeader}"/> <Button Grid.Row="10" Grid.Column="1" Content="Reset the Meter" Commands:Click.Command="{Binding ResetCommand}"/>   </Grid> </UserControl> The highlighted code from the above code shows data binding, for example ComboBox which displays list of states has it’s ItemsSource bound to States property, with DataTemplate bound to Name and SelectedItem  to SelectedState. You might be wondering what are all these properties and how it is able to bind to them.  The answer lies in data context, i.e., when you bound a control, WPF looks for data context on the root object (Grid in this case) and if it can’t find data context it will look into root’s root, i.e. FareView UserControl and it is bound to FareViewModel.  Each of those properties have be declared on the ViewModel for the View to bind correctly. To put simply, View is bound to ViewModel through data context of type object and every control that is bound on the View actually binds to the public property on the ViewModel. Lets look into the ViewModel code (the following code is not an exact copy of FareViewMode.cs, pasted relevant code for this section)   namespace TaxiModules.ViewModels { public class FareViewModel:ObservableBase, IDataErrorInfo { public List<USState> States { get { return USStates.StateList; } }   public USState SelectedState { get { return _selectedState; } set { _selectedState = value; RaisePropertyChanged(_selectedStatePropertyName); } }   public DateTime? DateOfEntry { get { return _dateOfEntry; } set { _dateOfEntry = value; RaisePropertyChanged(_dateOfEntryPropertyName); } }   public TimeSpan? TimeOfEntry { get { return _timeOfEntry; } set { _timeOfEntry = value; RaisePropertyChanged(_timeOfEntryPropertyName); } }   public double? MilesAtSixMPH { get { return _milesAtSixMPH; } set { _milesAtSixMPH = value; RaisePropertyChanged(_distanceAtSixMPHPropertyName); } }   public int? MinutesAtTweleveMPH { get { return _minutesAtTweleveMPH; } set { _minutesAtTweleveMPH = value; RaisePropertyChanged(_minutesAtTweleveMPHPropertyName); } }   public ICommand StartMeterCommand { get { if(_startMeterCommand == null) { _startMeterCommand = new DelegateCommand<object>(OnStartMeter, CanStartMeter); } return _startMeterCommand; } }   public ICommand AddMinutesCommand { get { if(_addMinutesCommand == null) { _addMinutesCommand = new DelegateCommand<object>(OnAddMinutes, CanAddMinutes); } return _addMinutesCommand; } }   public ICommand ResetCommand { get { if(_resetCommand == null) { _resetCommand = new DelegateCommand<object>(OnResetCommand); } return _resetCommand; } }   } private void OnStartMeter(object obj) { _eventAggregator.GetEvent<TaxiStartedEvent>().Publish( new TaxiStarted() { EngagedOn = DateOfEntry.Value.Date + TimeOfEntry.Value, EngagedState = SelectedState.Value });   _isMeterStarted = true; OnPropertyChanged(this,null); } And views communicate user actions like button clicks, tree view item selections, etc using commands. When user clicks on ‘Start the Meter’ button it invokes the method StartMeterCommand, which calls the method OnStartMeter which publishes the event to TotalViewModel using event aggregator  and TaxiStartedEvent. namespace TaxiModules.ViewModels { public class TotalViewModel:ObservableBase { ... private IEventAggregator _eventAggregator;   public TotalViewModel(IEventAggregator eventAggregator) { _eventAggregator = eventAggregator;   InitializePropertyNames(); InitializeModel(); SubscribeToEvents(); }   public decimal? TotalFare { get { return _totalFare; } set { _totalFare = value; RaisePropertyChanged(_totalFarePropertyName); } } .... private void SubscribeToEvents() { _eventAggregator.GetEvent<TaxiStartedEvent>().Subscribe(OnTaxiStarted, ThreadOption.UIThread,false,(filter) => true); _eventAggregator.GetEvent<TaxiOnMoveEvent>().Subscribe(OnTaxiMove, ThreadOption.UIThread, false, (filter) => true); _eventAggregator.GetEvent<TaxiResetEvent>().Subscribe(OnTaxiReset, ThreadOption.UIThread, false, (filter) => true); }   private void OnTaxiStarted(TaxiStarted taxiStarted) { Fares.Add(new EntryFare()); Fares.Add(new StateTaxFare(taxiStarted)); Fares.Add(new NightSurchargeFare(taxiStarted)); Fares.Add(new PeakHourWeekdayFare(taxiStarted));   SetTotalFare(Fares); }   private void SetTotalFare(IEnumerable<IFare> fares) { TotalFare = (_totalFare ?? 0) + TaxiFareHelper.GetTotalFare(fares); } ....   } }   TotalViewModel subscribes to events, TaxiStartedEvent and rest. When TaxiStartedEvent gets invoked it calls the OnTaxiStarted method which sets the total fare which includes entry fee, state tax, nightly surcharge, peak hour weekday fare.   Note that TotalViewModel derives from ObservableBase which implements the method RaisePropertyChanged which we are invoking in Set of TotalFare property, i.e, once we update the TotalFare property it raises an the event that  allows the TotalFare text box to fetch the new value through the data context. ViewModel is communicating with View through data context and it has no knowledge about View, helping in loose coupling of ViewModel and View.   I have attached the source code (.Net 4.0, Prism 4.0, VS 2010) , download and play with it and don’t forget to leave your comments.  

  Read the article

• StackOverFlowError while creating Mac object on AS400/Java

  - by Prasanna K Rao

  Hello all, I am a newbie to AS400-Java programming. I am trying to create my first program to test the implementation of Message Authentication Code (MAC). I am trying to use the HMACSHA1 hash function. My (Java 1.4) program runs fine on a dev box (V5R4).But fails terribly on the QA box (V5R3). My program is as below: ===================================================== import java.security.InvalidKeyException; import java.security.NoSuchAlgorithmException; import java.security.Security; import java.security.Provider; import javax.crypto.Mac; import javax.crypto.spec.SecretKeySpec; import javax.crypto.SecretKey; public class Test01 { private static final String HMAC_SHA1_ALGORITHM = "HmacSHA1"; public static void main (String [] arguments) { byte[] key = { 1,2,3,4,5,6,7,8}; SecretKeySpec SHA1key = new SecretKeySpec(key, "HmacSHA1"); Mac hmac; String strFinalRslt = ""; try { hmac = Mac.getInstance("HmacSHA1"); hmac.init(SHA1key); byte[] result = hmac.doFinal(); strFinalRslt = toHexString(result); }catch (NoSuchAlgorithmException e) { // TODO Auto-generated catch block e.printStackTrace(); }catch (InvalidKeyException e) { // TODO Auto-generated catch block e.printStackTrace(); }catch(StackOverflowError e){ e.printStackTrace(); } System.out.println(strFinalRslt); System.out.println("All done!!!"); } public static byte[] fromHexString ( String s ) { int stringLength = s.length(); if ( (stringLength & 0x1) != 0 ) { throw new IllegalArgumentException ( "fromHexString requires an even number of hex characters" ); } byte[] b = new byte[stringLength / 2]; for ( int i=0,j=0; i 4] ); //look up low nibble char sb.append( hexChar [b[i] & 0x0f] ); } return sb.toString(); } static char[] hexChar = { '0' , '1' , '2' , '3' , '4' , '5' , '6' , '7' , '8' , '9' , 'a' , 'b' , 'c' , 'd' , 'e' , 'f'}; } This program compiles fine and gets the correct response on my win-xp client and also my dev box. But, fails with the following error on the QA box: java.lang.StackOverflowError at java.lang.Throwable.(Throwable.java:180) at java.lang.Error.(Error.java:37) at java.lang.StackOverflowError.(StackOverflowError.java:24) at java.io.Os400FileSystem.list(Native method) at java.io.File.list(File.java:922) at javax.crypto.b.e(Unknown source) at javax.crypto.b.a(Unknown source) at javax.crypto.b.c(Unknown source) at javax.crypto.b£0.run(Unknown source) at javax.crypto.b.(Unknown source) at javax.crypto.Mac.getInstance(Unknown source) I have verified the java.security file and entry corresponding to the jce files are all ok. The DMPJVM command gives me the following response: Thu Jun 03 12:25:34 E Java Virtual Machine Information 016822/QPGMR/11111 ........................................................................ . Classpath . ........................................................................ java.version=1.4 sun.boot.class.path=/QIBM/ProdData/OS400/Java400/jdk/lib/jdkptf14.zip:/QIBM /ProdData/OS400/Java400/ext/ibmjssefw.jar:/QIBM/ProdData/CAP/ibmjsseprovide r.jar:/QIBM/ProdData/OS400/Java400/ext/ibmjsseprovider2.jar:/QIBM/ProdData/ OS400/Java400/ext/ibmpkcs11impl.jar:/QIBM/ProdData/CAP/ibmjssefips.jar:/QIB M/ProdData/OS400/Java400/jdk/lib/IBMiSeriesJSSE.jar:/QIBM/ProdData/OS400/Ja va400/jdk/lib/jce.jar:/QIBM/ProdData/OS400/Java400/jdk/lib/jaas.jar:/QIBM/P rodData/OS400/Java400/jdk/lib/ibmcertpathfw.jar:/QIBM/ProdData/OS400/Java40 0/jdk/lib/ibmcertpathprovider.jar:/QIBM/ProdData/OS400/Java400/ext/ibmpkcs. jar:/QIBM/ProdData/OS400/Java400/jdk/lib/ibmjgssfw.jar:/QIBM/ProdData/OS400 /Java400/jdk/lib/ibmjgssprovider.jar:/QIBM/ProdData/OS400/Java400/jdk/lib/s ecurity.jar:/QIBM/ProdData/OS400/Java400/jdk/lib/charsets.jar:/QIBM/ProdDat a/OS400/Java400/jdk/lib/resources.jar:/QIBM/ProdData/OS400/Java400/jdk/lib/ rt.jar:/QIBM/ProdData/OS400/Java400/jdk/lib/sunrsasign.jar:/QIBM/ProdData/O S400/Java400/ext/IBMmisc.jar:/QIBM/ProdData/Java400/ java.class.path=/myhome/lib/commons-codec-1.3.jar:/myhome/lib/commons-httpc lient-3.1.jar:/myhome/lib/commons-logging-1.1.jar:/myhome/lib/log4j-1.2.15.jar:/myhome/lib/log4j-core.jar ; java.ext.dirs=/QIBM/ProdData/OS400/Java400/jdk/lib/ext:/QIBM/UserData/Java4 00/ext:/QIBM/ProdData/Java400/jdk14/lib/ext java.library.path=/QSYS.LIB/ROBOTLIB.LIB:/QSYS.LIB/QTEMP.LIB:/QSYS.LIB/ODIP GM.LIB:/QSYS.LIB/QGPL.LIB ........................................................................ . Garbage Collection . ........................................................................ Garbage collector parameters Initial size: 16384 K Max size: 240000000 K Current values Heap size: 437952 K Garbage collections: 58 Additional values JIT heap size: 53824 K JVM heap size: 55752 K Last GC cycle time: 1333 ms ........................................................................ . Thread information . ........................................................................ Information for 4 thread(s) of 4 thread(s) processed Thread: 00000004 Thread-0 TDE: B00380000BAA0000 Thread priority: 5 Thread status: Running Thread group: main Runnable: java/lang/Thread Stack: java/io/Os400FileSystem.list(Ljava/io/File;)[Ljava/lang/String;+0 (Os400FileSystem.java:0) java/io/File.list()[Ljava/lang/String;+19 (File.java:922) javax/crypto/b.e()[B+127 (:0) javax/crypto/b.a(Ljava/security/cert/X509Certificate;)V+7 (:0) javax/crypto/b.access$500(Ljava/security/cert/X509Certificate;)V+1 (:0) javax/crypto/b$0.run()Ljava/lang/Object;+98 (:0) javax/crypto/b.()V+507 (:0) javax/crypto/Mac.getInstance(Ljava/lang/String;)Ljavax/crypto/Mac;+10 (:0) Locks: None Thread: 00000007 jitcompilethread TDE: B00380000BD58000 Thread priority: 5 Thread status: Java wait Thread group: system Runnable: java/lang/Thread Stack: None Locks: None Thread: 00000005 Reference Handler TDE: B00380000BAAC000 Thread priority: 10 Thread status: Waiting Wait object: java/lang/ref/Reference$Lock Thread group: system Runnable: java/lang/ref/Reference$ReferenceHandler Stack: java/lang/Object.wait()V+1 (Object.java:452) java/lang/ref/Reference$ReferenceHandler.run()V+47 (Reference.java:169) Locks: None Thread: 00000006 Finalizer TDE: B00380000BAB3000 Thread priority: 8 Thread status: Waiting Wait object: java/lang/ref/ReferenceQueue$Lock Thread group: system Runnable: java/lang/ref/Finalizer$FinalizerThread Stack: java/lang/ref/ReferenceQueue.remove(J)Ljava/lang/ref/Reference;+43 (ReferenceQueue.java:111) java/lang/ref/ReferenceQueue.remove()Ljava/lang/ref/Reference;+1 (ReferenceQueue.java:127) java/lang/ref/Finalizer$FinalizerThread.run()V+3 (Finalizer.java:171) Locks: None ........................................................................ . Class loader information . ........................................................................ 0 Default class loader 1 sun/reflect/DelegatingClassLoader 2 sun/misc/Launcher$ExtClassLoader ........................................................................ . GC heap information . ........................................................................ Loader Objects Class name ------ ------- ---------- 0 1493 [C 0 2122181 java/lang/String 0 47 [Ljava/util/Hashtable$Entry; 0 68 [Ljava/lang/Object; 0 1016 java/lang/Class 0 31 java/util/HashMap 0 37 java/util/Hashtable 0 2 java/lang/ThreadGroup 0 2 java/lang/RuntimePermission 0 2 java/lang/ref/ReferenceQueue$Null 0 5 java/lang/ref/ReferenceQueue 0 50 java/util/Vector 0 4 java/util/Stack 0 3 sun/misc/SoftCache 0 1 [Ljava/lang/ThreadGroup; 0 5 [Ljava/io/ObjectStreamField; 0 1 sun/reflect/ReflectionFactory 0 7 java/lang/ref/ReferenceQueue$Lock 0 10 java/lang/Object 0 1 java/lang/String$CaseInsensitiveComparator 0 1 java/util/Hashtable$EmptyEnumerator 0 1 java/util/Hashtable$EmptyIterator 0 33 [Ljava/util/HashMap$Entry; 0 19210 [J 0 1 sun/nio/cs/StandardCharsets 0 5 java/util/TreeMap 0 1075 java/util/TreeMap$Entry 0 469 [Ljava/lang/String; 0 1 java/lang/StringBuffer 0 2 java/io/FileInputStream 0 2 java/io/FileOutputStream 0 2 java/io/BufferedOutputStream 0 1 java/lang/reflect/ReflectPermission 0 1 [[Ljava/lang/ref/SoftReference; 0 2 [Ljava/lang/ref/SoftReference; 0 2 sun/nio/cs/Surrogate$Parser 0 3 sun/misc/Signal 0 1 [Ljava/io/File; 0 6 java/io/File 0 1 java/util/BitSet 0 17 sun/reflect/NativeConstructorAccessorImpl 0 2 java/net/URLClassLoader$ClassFinder 0 12 java/util/ArrayList 0 32 java/io/RandomAccessFile 0 16 java/lang/Thread 0 1 java/lang/ref/Reference$ReferenceHandler 0 1 java/lang/ref/Finalizer$FinalizerThread 0 266 [B 0 2 java/util/Properties 0 71 java/lang/ref/Finalizer 0 2 com/ibm/nio/cs/DirectEncoder 0 38 java/lang/reflect/Constructor 0 33 java/util/jar/JarFile 0 19200 java/lang/StackOverflowError 0 5 java/security/AccessControlContext 0 2 [Ljava/lang/Thread; 0 4 java/lang/OutOfMemoryError 0 1065 java/util/Hashtable$Entry 0 1 java/io/BufferedInputStream 0 2 java/io/PrintStream 0 2 java/io/OutputStreamWriter 0 428 [I 0 3 java/lang/ClassLoader$NativeLibrary 0 25 java/util/Locale 0 3 sun/misc/URLClassPath 0 30 java/util/zip/Inflater 0 612 java/util/HashMap$Entry 0 2 java/io/FilePermission 0 10 java/io/ObjectStreamField 0 1 java/security/BasicPermissionCollection 0 2 java/security/ProtectionDomain 0 1 java/lang/Integer$1 0 1 java/lang/ref/Reference$Lock 0 1 java/lang/Shutdown$Lock 0 1 java/lang/Runtime 0 36 java/io/FileDescriptor 0 1 java/lang/Long$1 0 202 java/lang/Long 0 3 java/lang/ThreadLocal 0 3 java/nio/charset/CodingErrorAction 0 2 java/nio/charset/CoderResult 0 1 java/nio/charset/CoderResult$1 0 1 java/nio/charset/CoderResult$2 0 1 sun/misc/Unsafe 0 2 java/nio/ByteOrder 0 1 java/io/Os400FileSystem 0 3 java/lang/Boolean 0 1 java/lang/Terminator$1 0 23 java/lang/Integer 0 2 sun/misc/NativeSignalHandler 0 1 sun/misc/Launcher$Factory 0 1 sun/misc/Launcher 0 53 [Ljava/lang/Class; 0 1 java/lang/reflect/ReflectAccess 0 18 sun/reflect/DelegatingConstructorAccessorImpl 0 1 sun/net/www/protocol/file/Handler 0 3 java/util/HashSet 0 3 sun/net/www/protocol/jar/Handler 0 1 java/util/jar/JavaUtilJarAccessImpl 0 1 java/net/UnknownContentHandler 0 2 [Ljava/security/Principal; 0 10 [Ljava/security/cert/Certificate; 0 2 sun/misc/AtomicLongCSImpl 0 3 sun/reflect/DelegatingMethodAccessorImpl 0 1 sun/security/util/ByteArrayLexOrder 0 1 sun/security/util/ByteArrayTagOrder 0 7 sun/security/x509/CertificateVersion 0 7 sun/security/x509/CertificateSerialNumber 0 7 sun/security/x509/SerialNumber 0 7 sun/security/x509/CertificateAlgorithmId 0 7 sun/security/x509/CertificateIssuerName 0 60 sun/security/x509/RDN 0 60 [Lsun/security/x509/AVA; 0 67 sun/security/util/DerInputStream 0 3 [Ljava/math/BigInteger; 0 2 com/ibm/nio/cs/Converter 0 2 sun/nio/cs/StreamEncoder$CharsetSE 0 35 java/lang/ref/SoftReference 0 2 java/nio/HeapByteBuffer 0 2 java/io/BufferedWriter 0 33 sun/misc/URLClassPath$JarLoader 0 4 java/lang/ThreadLocal$ThreadLocalMap$Entry 0 76 java/net/URL 0 1 sun/misc/Launcher$ExtClassLoader 0 1 sun/misc/Launcher$AppClassLoader 0 4 java/lang/Throwable 0 7 java/lang/reflect/Method 0 2 sun/misc/URLClassPath$FileLoader 0 2 java/security/CodeSource 0 2 java/security/Permissions 0 2 java/io/FilePermissionCollection 0 1 java/lang/ThreadLocal$ThreadLocalMap 0 1 javax/crypto/spec/SecretKeySpec 0 17 java/util/jar/Attributes$Name 0 1 [Ljava/lang/ThreadLocal$ThreadLocalMap$Entry; 0 1 java/security/SecureRandom 0 2 sun/security/provider/Sun 0 1 java/util/jar/JarFile$JarFileEntry 0 1 java/util/jar/JarVerifier 0 3 sun/reflect/NativeMethodAccessorImpl 0 116 sun/security/util/ObjectIdentifier 0 1 java/lang/Package 0 2 [S 0 104 java/math/BigInteger 0 20 sun/security/x509/AlgorithmId 0 14 sun/security/x509/X500Name 0 14 [Lsun/security/x509/RDN; 0 60 sun/security/x509/AVA 0 67 sun/security/util/DerValue 0 67 sun/security/util/DerInputBuffer 0 21 sun/security/x509/AVAKeyword 0 6 sun/security/x509/X509CertImpl 0 7 sun/security/x509/X509CertInfo 0 1 [Lsun/security/util/ObjectIdentifier; 0 1 [[Ljava/lang/Byte; 0 3 [[B 0 7 sun/security/provider/DSAPublicKey 0 7 sun/security/x509/AuthorityKeyIdentifierExtension 0 12 [Ljava/lang/Byte; 0 14 java/lang/Byte 0 7 sun/security/x509/CertificateSubjectName 0 7 sun/security/x509/CertificateX509Key 0 14 sun/security/x509/KeyIdentifier 0 4 [Z 0 5 sun/text/Normalizer$Mode 0 7 sun/security/x509/CertificateValidity 0 14 java/util/Date 0 7 sun/security/provider/DSAParameters 0 7 sun/security/util/BitArray 0 7 sun/security/x509/CertificateExtensions 0 7 java/security/AlgorithmParameters 0 7 sun/security/x509/SubjectKeyIdentifierExtension 0 5 sun/security/x509/BasicConstraintsExtension 0 2 sun/security/x509/KeyUsageExtension 0 1 sun/text/CompactCharArray 0 1 sun/text/CompactByteArray 0 1 sun/net/www/protocol/jar/JarFileFactory 0 1 java/util/Collections$EmptySet 0 1 java/util/Collections$EmptyList 0 1 java/util/Collections$ReverseComparator 0 1 com/ibm/security/jgss/i18n/PropertyResource 0 1 javax/crypto/b$0 0 1 sun/security/provider/X509Factory 0 1 sun/reflect/BootstrapConstructorAccessorImpl 1 1 sun/reflect/GeneratedConstructorAccessor3202134454 2 1 com/ibm/crypto/provider/IBMJCE 0 6 java/util/ResourceBundle$LoaderReference 0 1 [Lsun/security/x509/NetscapeCertTypeExtension$MapEntry; 0 1 com/sun/rsajca/Provider 0 1 com/ibm/security/cert/IBMCertPath 0 1 com/ibm/as400/ibmonly/net/ssl/Provider 0 1 com/ibm/jsse/IBMJSSEProvider 0 1 com/ibm/security/jgss/IBMJGSSProvider 0 5 org/ietf/jgss/Oid 0 1 java/util/PropertyResourceBundle 0 7 java/util/ResourceBundle$ResourceCacheKey 0 2 sun/net/www/protocol/jar/URLJarFile 0 6 sun/misc/SoftCache$ValueCell 0 1 java/util/Random 0 1 java/util/Collections$EmptyMap 0 112 com/ibm/security/util/ObjectIdentifier 0 5 java/security/Security$ProviderProperty 0 1 java/security/cert/CertificateFactory 0 1 sun/security/provider/SecureRandom 0 2 java/security/MessageDigest$Delegate 0 2 sun/security/provider/SHA 0 1 sun/util/calendar/ZoneInfo 0 4 com/ibm/security/x509/X500Name 0 2 [Ljava/security/cert/X509Certificate; 0 1 sun/reflect/DelegatingClassLoader 0 1 sun/security/x509/NetscapeCertTypeExtension 0 7 sun/security/x509/NetscapeCertTypeExtension$MapEntry 0 3 [[Ljava/lang/String; 0 3 java/util/Arrays$ArrayList 0 7 com/ibm/security/x509/NetscapeCertTypeExtension$MapEntry 0 1 com/ibm/security/validator/EndEntityChecker 0 1 java/util/AbstractList$Itr 0 1 com/ibm/security/util/ByteArrayLexOrder 0 1 com/ibm/security/util/ByteArrayTagOrder 0 18 [Lcom/ibm/security/x509/AVA; 0 18 com/ibm/security/util/DerInputStream 0 5 com/ibm/security/util/text/Normalizer$Mode 0 1 com/ibm/security/validator/SimpleValidator 0 1 [Lcom/ibm/security/x509/NetscapeCertTypeExtension$MapEntry; 0 4 [Lcom/ibm/security/x509/RDN; 0 1 java/util/Hashtable$Enumerator 0 4 java/util/LinkedHashMap$Entry 0 1 sun/text/resources/LocaleElements 0 1 sun/text/resources/LocaleElements_en 0 22 com/ibm/security/x509/AVAKeyword 0 4 javax/security/auth/x500/X500Principal 0 18 com/ibm/security/x509/RDN 0 18 com/ibm/security/x509/AVA 0 18 com/ibm/security/util/DerInputBuffer 0 18 com/ibm/security/util/DerValue 0 1 com/ibm/security/util/text/CompactCharArray 0 1 com/ibm/security/util/text/CompactByteArray 0 2 java/util/LinkedHashMap 0 1 java/net/InetAddress$1 0 2 [Ljava/net/InetAddress; 0 2 java/net/InetAddress$Cache 0 1 java/net/Inet4AddressImpl 0 3 java/net/Inet4Address 0 2 java/net/InetAddress$CacheEntry ........................................................................ . Global registry information . ........................................................................ Loader Objects Class name ------ ------- ---------- 0 23 [C 0 1017 java/lang/Class 0 1 java/lang/ref/Reference$ReferenceHandler 0 1 java/lang/ref/Finalizer$FinalizerThread 0 1 sun/misc/Launcher$AppClassLoader 0 32 java/io/RandomAccessFile 0 32 [B Can someone please advise me? Thanks a lot, Prasanna

  Read the article

• 26 Days: Countdown to Oracle OpenWorld 2012

  - by Michael Snow

  Welcome to our countdown to Oracle OpenWorld! Oracle OpenWorld 2012 is just around the corner. In less than 26 days, San Francisco will be invaded by an expected 50,000 people from all over the world. Here on the Oracle WebCenter team, we’ve all been working to help make the experience a great one for all our WebCenter customers. For a sneak peak  – we’ll be spending this week giving you a teaser of what to look forward to if you are joining us in San Francisco from September 30th through October 4th. We have Oracle WebCenter sessions covering all topics imaginable. Take a look and use the tools we provide to build out your schedule in advance and reserve your seats in your favorite sessions.  That gives you plenty of time to plan for your week with us in San Francisco. If unfortunately, your boss denied your request to attend - there are still some ways that you can join in the experience virtually On-Demand. This year - we are expanding even more up North of Market Street and will be taking over Union Square as well. Check out this map of San Francisco to get a sense of how much of a footprint Oracle OpenWorld has grown to this year. With so much to see and so many sessions to learn from - its no wonder that people get excited. Add to that a good mix of fun and all of the possible WebCenter sessions you could attend - you won't want to sleep at all to take full advantage of such an opportunity. We'll also have our annual WebCenter Customer Appreciation reception - stay tuned this week for some more info on registration to make sure you'll be able to join us. If you've been following the America's Cup at all and believe in EXTREME PERFORMANCE you'll definitely want to take a look at this video from last year's OpenWorld Keynote. 12.00 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-family:"Calibri","sans-serif"; mso-ascii- mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi- mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Important OpenWorld Links:  Attendee / Presenters Toolkit Oracle Schedule Builder WebCenter Sessions (listed in the catalog under Fusion Middleware as "Portals, Sites, Content, and Collaboration" ) Oracle Music Festival - AMAZING Line up!!  Oracle Customer Appreciation Night -LOOK HERE!! Oracle OpenWorld LIVE On-Demand Here are all the WebCenter sessions broken down by day for your viewing pleasure. Monday, October 1st CON8885 - Simplify CRM Engagement with Contextual Collaboration Are your sales teams disconnected and disengaged? Do you want a tool for easily connecting expertise across your organization and providing visibility into the complete sales process? Do you want a way to enhance and retain organization knowledge? Oracle Social Network is the answer. Attend this session to learn how to make CRM easy, effective, and efficient for use across virtual sales teams. Also learn how Oracle Social Network can drive sales force collaboration with natural conversations throughout the sales cycle, promote sales team productivity through purposeful social networking without the noise, and build cross-team knowledge by integrating conversations with CRM and other business applications. CON8268 - Oracle WebCenter Strategy: Engaging Your Customers. Empowering Your Business Oracle WebCenter is a user engagement platform for social business, connecting people and information. Attend this session to learn about the Oracle WebCenter strategy, and understand where Oracle is taking the platform to help companies engage customers, empower employees, and enable partners. Business success starts with ensuring that everyone is engaged with the right people and the right information and can access what they need through the channel of their choice—Web, mobile, or social. Are you giving customers, employees, and partners the best-possible experience? Come learn how you can! ¶ HOL10208 - Add Social Capabilities to Your Enterprise Applications Oracle Social Network enables you to add real-time collaboration capabilities into your enterprise applications, so that conversations can happen directly within your business systems. In this hands-on lab, you will try out the Oracle Social Network product to collaborate with other attendees, using real-time conversations with document sharing capabilities. Next you will embed social capabilities into a sample Web-based enterprise application, using embedded UI components. Experts will also write simple REST-based integrations, using the Oracle Social Network API to programmatically create social interactions. ¶ CON8893 - Improve Employee Productivity with Intuitive and Social Work Environments Social technologies have already transformed the ways customers, employees, partners, and suppliers communicate and stay informed. Forward-thinking organizations today need technologies and infrastructures to help them advance to the next level and integrate social activities with business applications to deliver a user experience that simplifies business processes and enterprise application engagement. Attend this session to hear from an innovative Oracle Social Network customer and learn how you can improve productivity with intuitive and social work environments and empower your employees with innovative social tools to enable contextual access to content and dynamic personalization of solutions. ¶ CON8270 - Oracle WebCenter Content Strategy and Vision Oracle WebCenter provides a strategic content infrastructure for managing documents, images, e-mails, and rich media files. With a single repository, organizations can address any content use case, such as accounts payable, HR onboarding, document management, compliance, records management, digital asset management, or Website management. In this session, learn about future plans for how Oracle WebCenter will address new use cases as well as new integrations with Oracle Fusion Middleware and Oracle Applications, leveraging your investments by making your users more productive and error-free. ¶ CON8269 - Oracle WebCenter Sites Strategy and Vision Oracle’s Web experience management solution, Oracle WebCenter Sites, enables organizations to use the online channel to drive customer acquisition and brand loyalty. It helps marketers and business users easily create and manage contextually relevant, social, interactive online experiences across multiple channels on a global scale. In this session, learn about future plans for how Oracle WebCenter Sites will provide you with the tools, capabilities, and integrations you need in order to continue to address your customers’ evolving requirements for engaging online experiences and keep moving your business forward. ¶ CON8896 - Living with SharePoint SharePoint is a popular platform, but it’s not always the best fit for Oracle customers. In this session, you’ll discover the technical and nontechnical limitations and pitfalls of SharePoint and learn about Oracle alternatives for collaboration, portals, enterprise and Web content management, social computing, and application integration. The presentation shows you how to integrate with SharePoint when business or IT requirements dictate and covers cloud-based (Office 365) and on-premises versions of SharePoint. Presented by a former Microsoft director of SharePoint product management and backed by independent customer research, this session will prepare you to answer the question “Why don’t we just use SharePoint for that?’ the next time it comes up in your organization. ¶ CON7843 - Content-Enabling Enterprise Processes with Oracle WebCenter Organizations today continually strive to automate business processes, reduce costs, and improve efficiency. Many business processes are content-intensive and unstructured, requiring ad hoc collaboration, and distributed in nature, requiring many approvals and generating huge volumes of paper. In this session, learn how Oracle and SYSTIME have partnered to help a customer content-enable its enterprise with Oracle WebCenter Content and Oracle WebCenter Imaging 11g and integrate them with Oracle Applications. ¶ CON6114 - Tape Robotics’ Newest Superhero: Now Fueled by Oracle Software For small, midsize, and rapidly growing businesses that want the most energy-efficient, scalable storage infrastructure to meet their rapidly growing data demands, Oracle’s most recent addition to its award-winning tape portfolio leverages several pieces of Oracle software. With Oracle Linux, Oracle WebLogic, and Oracle Fusion Middleware tools, the library achieves a higher level of usability than previous products while offering customers a familiar interface for management, plus ease of use. This session examines the competitive advantages of the tape library and how Oracle software raises customer satisfaction. Learn how the combination of Oracle engineered systems, Oracle Secure Backup, and Oracle’s StorageTek tape libraries provide end-to-end coverage of your data. ¶ CON9437 - Mobile Access Management With more than five billion mobile devices on the planet and an increasing number of users using their own devices to access corporate data and applications, securely extending identity management to mobile devices has become a hot topic. This session focuses on how to extend your existing identity management infrastructure and policies to securely and seamlessly enable mobile user access. CON7815 - Customer Experience Online in Cloud: Oracle WebCenter Sites, Oracle ATG Apps, Oracle Exalogic Oracle WebCenter Sites and Oracle’s ATG product line together can provide a compelling marketing and e-commerce experience. When you couple them with the extreme performance of Oracle Exalogic, you’ll see unmatched scalability that provides you with a true cloud-based solution. In this session, you’ll learn how running Oracle WebCenter Sites and ATG applications on Oracle Exalogic delivers both a private and a public cloud experience. Find out what it takes to get these systems working together and delivering engaging Web experiences. Even if you aren’t considering Oracle Exalogic today, the rich Web experience of Oracle WebCenter, paired with the depth of the ATG product line, can provide your business full support, from merchandising through sale completion. ¶ CON8271 - Oracle WebCenter Portal Strategy and Vision To innovate and keep a competitive edge, organizations need to leverage the power of agile and responsive Web applications. Oracle WebCenter Portal enables you to do just that, by delivering intuitive user experiences for enterprise applications to drive innovation with composite applications and mashups. Attend this session to learn firsthand from customers how Oracle WebCenter Portal extends the value of existing enterprise applications, business processes, and content; delivers a superior business user experience; and maximizes limited IT resources. ¶ CON8880 - The Connected Customer Experience Begins with the Online Channel There’s a lot of talk these days about how to connect the customer journey across various touchpoints—from Websites and e-commerce to call centers and in-store—to provide experiences that are more relevant and engaging and ultimately gain competitive edge. Doing it all at once isn’t a realistic objective, so where do you start? Come to this session, and hear about three steps you can take that can help you begin your journey toward delivering the connected customer experience. You’ll hear how Oracle now has an integrated digital marketing platform for your corporate Website, your e-commerce site, your self-service portal, and your marketing and loyalty campaigns, and you’ll learn what you can do today to begin executing on your customer experience initiatives. ¶ GEN11451 - General Session: Building Mobile Applications with Oracle Cloud With the prevalence of smart mobile devices, companies are facing an increased demand to provide access to data and applications from new channels. However, developing applications for mobile devices poses some unique challenges. Come to this session to learn how Oracle addresses these challenges, offering a simpler way to develop and deploy cross-device mobile applications. See how Oracle Cloud enables you to access applications, data, and services from mobile channels in an easier way.  CON8272 - Oracle Social Network Strategy and Vision One key way of increasing employee productivity is by bringing people, processes, and information together—providing new social capabilities to enable business users to quickly correspond and collaborate on business activities. Oracle WebCenter provides a user engagement platform with social and collaborative technologies to empower business users to focus on their key business processes, applications, and content in the context of their role and process. Attend this session to hear how the latest social capabilities in Oracle Social Network are enabling organizations to transform themselves into social businesses.  --- Tuesday, October 2nd HOL10194 - Enterprise Content Management Simplified: Oracle WebCenter Content’s Next-Generation UI Regardless of the nature of your business, unstructured content underpins many of its daily functions. Whether you are working with traditional presentations, spreadsheets, or text documents—or even with digital assets such as images and multimedia files—your content needs to be accessible and manageable in convenient and intuitive ways to make working with the content easier. Additionally, you need the ability to easily share documents with coworkers to facilitate a collaborative working environment. Come to this session to see how Oracle WebCenter Content’s next-generation user interface helps modern knowledge workers easily manage personal and enterprise documents in a collaborative environment.¶ CON8877 - Develop a Mobile Strategy with Oracle WebCenter: Engage Customers, Employees, and Partners Mobile technology has gone from nice-to-have to a cornerstone of user engagement. Mobile access enables users to have information available at their fingertips, enabling them to take action the moment they make a decision, interact in the moment of convenience, and take advantage of new service offerings in their preferred channels. All your employees have your mobile applications in their pocket; now what are you going to do? It is a critical step for companies to think through what their employees, customers, and partners really need on their devices. Attend this session to see how Oracle WebCenter enables you to better engage your customers, employees, and partners by providing a unified experience across multiple channels. ¶ CON9447 - Enabling Access for Hundreds of Millions of Users How do you grow your business by identifying, authenticating, authorizing, and federating users on the Web, leveraging social identity and the open source OAuth protocol? How do you scale your access management solution to support hundreds of millions of users? With social identity support out of the box, Oracle’s access management solution is also benchmarked for 250-million-user deployment according to real-world customer scenarios. In this session, you will learn about the social identity capability and the 250-million-user benchmark testing of Oracle Access Manager and Oracle Adaptive Access Manager running on Oracle Exalogic and Oracle Exadata. ¶ HOL10207 - Build an Intranet Portal with Oracle WebCenter In this hands-on lab, you’ll work with Oracle WebCenter Portal and Oracle WebCenter Content to build out an enterprise portal that maximizes the productivity of teams and individual contributors. Using browser-based tools, you’ll manage site resources such as page styles, templates, and navigation. You’ll edit content stored in Oracle WebCenter Content directly from your portal. You’ll also experience the latest features that promote collaboration, social networking, and personal productivity. ¶ CON2906 - Get Proactive: Best Practices for Maintaining Oracle Fusion Middleware You chose Oracle Fusion Middleware products to help your organization deliver superior business results. Now learn how to take full advantage of your software with all the great tools, resources, and product updates you’re entitled to through Oracle Support. In this session, Oracle product experts provide proven best practices to help you work more efficiently, plan and prepare for upgrades and patching more effectively, and manage risk. Topics include configuration management tools, remote diagnostics, My Oracle Support Community, and My Oracle Support Lifecycle Advisors. New users and Oracle Fusion Middleware experts alike are guaranteed to leave with fresh ideas and practical, easy-to-implement next steps. ¶ CON8878 - Oracle WebCenter’s Cloud Strategy: From Social and Platform Services to Mashups Cloud computing represents a paradigm shift in how we build applications, automate processes, collaborate, and share and in how we secure our enterprise. Additionally, as you adopt cloud-based services in your organization, it’s likely that you will still have many critical on-premises applications running. With these mixed environments, multiple user interfaces, different security, and multiple datasources and content sources, how do you start evolving your strategy to account for these challenges? Oracle WebCenter offers a complete array of technologies enabling you to solve these challenges and prepare you for the cloud. Attend this session to learn how you can use Oracle WebCenter in the cloud as well as create on-premises and cloud application mash-ups. ¶ CON8901 - Optimize Enterprise Business Processes with Oracle WebCenter and Oracle BPM Do you have business processes that span multiple applications? Are you grappling with how to have visibility across these business processes; how to manage content that is associated with these processes; and, most importantly, how to model and optimize these business processes? Attend this session to hear how Oracle WebCenter and Oracle Business Process Management provide a unique set of integrated solutions to provide a composite application dashboard across these business processes and offer a solution for content-centric business processes. ¶ CON8883 - Deliver Engaging Interfaces to Oracle Applications with Oracle WebCenter Critical business processes live within enterprise applications, and application users need to manage and execute these processes as effectively as possible. Oracle provides a comprehensive user engagement platform to increase user productivity and optimize overall processes within Oracle Applications—Oracle E-Business Suite and Oracle’s Siebel, PeopleSoft, and JD Edwards product families—and third-party applications. Attend this session to learn how you can integrate these applications with Oracle WebCenter to deliver composite application dashboards to your end users—whether they are your customers, partners, or employees—for enhanced usability and Web 2.0–enabled enterprise portals.¶ Wednesday, October 3rd CON8895 - Future-Ready Intranets: How Aramark Re-engineered the Application Landscape There are essential techniques and technologies you can use to deliver employee portals that garner higher productivity, improve business efficiency, and increase user engagement. Attend this session to learn how you can leverage Oracle WebCenter Portal as a user engagement platform for bringing together business process management, enterprise content management, and business intelligence into a highly relevant and integrated experience. Hear how Aramark has leveraged Oracle WebCenter Portal and Oracle WebCenter Content to deliver a unified workspace providing simpler navigation and processing, consolidation of tools, easy access to information, integrated search, and single sign-on. ¶ CON8886 - Content Consolidation: Save Money, Increase Efficiency, and Eliminate Silos Organizations are looking for ways to save money and be more efficient. With content in many different places, it’s difficult to know where to look for a document and whether the document is the most current version. With Oracle WebCenter, content can be consolidated into one best-of-breed repository that is secure, scalable, and integrated with your business processes and applications. Users can find the content they need, where they need it, and ensure that it is the right content. This session covers content challenges that affect your business; content consolidation that can lead to savings in storage and administration costs and can lower risks; and how companies are realizing savings. ¶ CON8911 - Improve Online Experiences for Customers and Partners with Self-Service Portals Are you able to provide your customers and partners an easy-to-use online self-service experience? Are you processing high-volume transactions and struggling with call center bottlenecks or back-end systems that won’t integrate, causing order delays and customer frustration? Are you looking to target content such as product and service offerings to your end users? This session shares approaches to providing targeted delivery as well as strategies and best practices for transforming your business by providing an intuitive user experience for your customers and partners. ¶ CON6156 - Top 10 Ways to Integrate Oracle WebCenter Content This session covers 10 common ways to integrate Oracle WebCenter Content with other enterprise applications and middleware. It discusses out-of-the-box modules that provide expanded features in Oracle WebCenter Content—such as enterprise search, SOA, and BPEL—as well as developer tools you can use to create custom integrations. The presentation also gives guidance on which integration option may work best in your environment. ¶ HOL10207 - Build an Intranet Portal with Oracle WebCenter In this hands-on lab, you’ll work with Oracle WebCenter Portal and Oracle WebCenter Content to build out an enterprise portal that maximizes the productivity of teams and individual contributors. Using browser-based tools, you’ll manage site resources such as page styles, templates, and navigation. You’ll edit content stored in Oracle WebCenter Content directly from your portal. You’ll also experience the latest features that promote collaboration, social networking, and personal productivity. ¶ CON7817 - Migration to Oracle WebCenter Imaging 11g Customers today continually strive to automate business processes, reduce costs, and improve efficiency. The accounts payable process—which is often distributed in nature, requires many approvals, and generates huge volumes of paper invoices—is automated by many customers. In this session, learn how Oracle and SYSTIME have partnered to help a customer migrate its existing Oracle Imaging and Process Management Release 7.6 to the latest Oracle WebCenter Imaging 11g and integrate it with Oracle’s JD Edwards family of products. ¶ CON8910 - How to Engage Customers Across Web, Mobile, and Social Channels Whether on desktops at the office, on tablets at home, or on mobile phones when on the go, today’s customers are always connected. To engage today’s customers, you need to make the online customer experience connected and consistent across a host of devices and multiple channels, including Web, mobile, and social networks. Managing this multichannel environment can result in lots of headaches without the right tools. Attend this session to learn how Oracle WebCenter Sites solves the challenge of multichannel customer engagement. ¶ HOL10206 - Oracle WebCenter Sites 11g: Transforming the Content Contributor Experience Oracle WebCenter Sites 11g makes it easy for marketers and business users to contribute to and manage Websites with the new visual, contextual, and intuitive Web authoring interface. In this hands-on lab, you will create and manage content for a sports-themed Website, using many of the new and enhanced features of the 11g release. ¶ CON8900 - Building Next-Generation Portals: An Interactive Customer Panel Discussion Social and collaborative technologies have changed how people interact, learn, and collaborate, and providing a modern, social Web presence is imperative to remain competitive in today’s market. Can your business benefit from a more collaborative and interactive portal environment for employees, customers, and partners? Attend this session to hear from Oracle WebCenter Portal customers as they share their strategies and best practices for providing users with a modern experience that adapts to their needs and includes personalized access to content in context. The panel also addresses how customers have benefited from creating next-generation portals by migrating from older portal technologies to Oracle WebCenter Portal. ¶ CON9625 - Taking Control of Oracle WebCenter Security Organizations are increasingly looking to extend their Oracle WebCenter portal for social business, to serve external users and provide seamless access to the right information. In particular, many organizations are extending Oracle WebCenter in a business-to-business scenario requiring secure identification and authorization of business partners and their users. This session focuses on how customers are leveraging, securing, and providing access control to Oracle WebCenter portal and mobile solutions. You will learn best practices and hear real-world examples of how to provide flexible and granular access control for Oracle WebCenter deployments, using Oracle Platform Security Services and Oracle Access Management Suite product offerings. ¶ CON8891 - Extending Social into Enterprise Applications and Business Processes Oracle Social Network is an extensible social platform that enables contextual collaboration within enterprise applications and business processes, providing relevant data from across various enterprise systems in one place. Attend this session to see how an Oracle Social Network customer is integrating multiple applications—such as CRM, HCM, and business processes—into Oracle Social Network and Oracle WebCenter to enable individuals and teams to solve complex cross-organizational business problems more effectively by utilizing the social enterprise. ¶ Thursday, October 4th CON8899 - Becoming a Social Business: Stories from the Front Lines of Change What does it really mean to be a social business? How can you change our organization to embrace social approaches? What pitfalls do you need to avoid? In this lively panel discussion, customer and industry thought leaders in social business explore these topics and more as they share their stories of the good, the bad, and the ugly that can happen when embracing social methods and technologies to improve business success. Using moderated questions and open Q&A from the audience, the panel discusses vital topics such as the critical factors for success, the major issues to avoid, how to gain senior executive support for social efforts, how to handle undesired behavior, and how to measure business impact. It takes a thought-provoking look at becoming a social business from the inside. ¶ CON6851 - Oracle WebCenter and Oracle Business Intelligence Enterprise Edition to Create Vendor Portals Large manufacturers of grocery items routinely find themselves depending on the inventory management expertise of their wholesalers and distributors. Inventory costs can be managed more efficiently by the manufacturers if they have better insight into the inventory levels of items carried by their distributors. This creates a unique opportunity for distributors and wholesalers to leverage this knowledge into a revenue-generating subscription service. Oracle Business Intelligence Enterprise Edition and Oracle WebCenter Portal play a key part in enabling creation of business-managed business intelligence portals for vendors. This session discusses one customer that implemented this by leveraging Oracle WebCenter and Oracle Business Intelligence Enterprise Edition. ¶ CON8879 - Provide a Personalized and Consistent Customer Experience in Your Websites and Portals Your customers engage with your company online in different ways throughout their journey—from prospecting by acquiring information on your corporate Website to transacting through self-service applications on your customer portal—and then the cycle begins again when they look for new products and services. Ensuring that the customer experience is consistent and personalized across online properties—from branding and content to interactions and transactions—can be a daunting task. Oracle WebCenter enables you to speak and interact with your customers with one voice across your Websites and portals by providing an integrated platform for delivery of self-service and engagement that unifies and personalizes the online experience. Learn more in this session. ¶ CON8898 - Land Mines, Potholes, and Dirt Roads: Navigating the Way to ECM Nirvana Ten years ago, people were predicting that by this time in history, we’d be some kind of utopian paperless society. As we all know, we’re not there yet, but are we getting closer? What is keeping companies from driving down the road to enterprise content management bliss? Most people understand that using ECM as a central platform enables organizations to expedite document-centric processes, but most business processes in organizations are still heavily paper-based. Many of these processes could be automated and improved with an ECM platform infrastructure. In this panel discussion, you’ll hear from Oracle WebCenter customers that have already solved some of these challenges as they share their strategies for success and roads to avoid along your journey. ¶ CON8908 - Oracle WebCenter Portal: Creating and Using Content Presenter Templates Oracle WebCenter Portal applications use task flows to display and integrate content stored in the Oracle WebCenter Content server. Among the most flexible task flows is Content Presenter, which renders various types of content on an Oracle WebCenter Portal page. Although Oracle WebCenter Portal comes with a set of predefined Content Presenter templates, developers can create their own templates for specific rendering needs. This session shows the lifecycle of developing Content Presenter task flows, including how to create, package, import, modify at runtime, and use such templates. In addition to simple examples with Oracle Application Development Framework (Oracle ADF) UI elements to render the content, it shows how to use other UI technologies, CSS files, and JavaScript libraries. ¶ CON8897 - Using Web Experience Management to Drive Online Marketing Success Every year, the online channel becomes more imperative for driving organizational top-line revenue, but for many companies, mastering how to best market their products and services in a fast-evolving online world with high customer expectations for personalized experiences can be a complex proposition. Come to this panel discussion, and hear directly from online marketers how they are succeeding today by using Web experience management to drive marketing success, using capabilities such as targeting and optimization, user-generated content, mobile site publishing, and site visitor personalization to deliver engaging online experiences. ¶ CON8892 - Oracle’s Journey to Social Business Social business is a revolution, one that is causing rapidly accelerating change in how companies and customers engage with one another and how employees work together. Oracle’s goal in becoming a social business is to create a socially connected organization in which working collaboratively across geographical locations, lines of business, and management chains is second nature, enabling innovative solutions to business challenges. We can achieve this by connecting the right people, finding the right content, communicating with the right people, collaborating at the right time, and building the right communities in the right context—all ready in the CLOUD. Attend this session to see how Oracle is transforming itself into a social business. ¶  ------------ If you've read all the way to the end here - we are REALLY looking forward to seeing you in San Francisco.

  Read the article

• Problem with cometd and jetty 6 / 7

  - by Ceilingfish

  Hi chaps, I'm trying to get started with cometd (http://cometd.org/) and jetty 6 or 7, but I seem to be having problems. I've got an ant script that packages my code up into a war with the cometd 1.1.1 binaries and jetty binaries that are appropriate to the version of jetty I deploy the war to (so 7.1.2.v20100523 binaries when I deploy to jetty 7.1.2.v20100523 and 6.1.24 when I deploy to 6.1.24). I first tried getting a setup with version 7.1.2.v20100523, but when I tried to deploy I got a very long stack trace sample of which is: 2010-05-26 15:32:12.906:WARN::Problem processing jar entry org/eclipse/jetty/util/MultiPartOutputStream.class java.io.IOException: Invalid resource at org.eclipse.jetty.util.resource.URLResource.getInputStream(URLResource.java:204) at org.eclipse.jetty.util.resource.JarResource.getInputStream(JarResource.java:113) at org.eclipse.jetty.annotations.AnnotationParser$2.processEntry(AnnotationParser.java:575) at org.eclipse.jetty.webapp.JarScanner.matched(JarScanner.java:152) at org.eclipse.jetty.util.PatternMatcher.matchPatterns(PatternMatcher.java:82) at org.eclipse.jetty.util.PatternMatcher.match(PatternMatcher.java:64) at org.eclipse.jetty.webapp.JarScanner.scan(JarScanner.java:75) at org.eclipse.jetty.annotations.AnnotationParser.parse(AnnotationParser.java:587) at org.eclipse.jetty.annotations.AbstractConfiguration.parseWebInfLib(AbstractConfiguration.java:107) at org.eclipse.jetty.annotations.AnnotationConfiguration.configure(AnnotationConfiguration.java:68) at org.eclipse.jetty.webapp.WebAppContext.startContext(WebAppContext.java:992) at org.eclipse.jetty.server.handler.ContextHandler.doStart(ContextHandler.java:579) at org.eclipse.jetty.webapp.WebAppContext.doStart(WebAppContext.java:381) at org.eclipse.jetty.util.component.AbstractLifeCycle.start(AbstractLifeCycle.java:55) at org.eclipse.jetty.deploy.bindings.StandardStarter.processBinding(StandardStarter.java:36) at org.eclipse.jetty.deploy.AppLifeCycle.runBindings(AppLifeCycle.java:182) at org.eclipse.jetty.deploy.DeploymentManager.requestAppGoal(DeploymentManager.java:497) at org.eclipse.jetty.deploy.DeploymentManager.addApp(DeploymentManager.java:135) at org.eclipse.jetty.deploy.providers.ScanningAppProvider$1.fileChanged(ScanningAppProvider.java:77) at org.eclipse.jetty.util.Scanner.reportChange(Scanner.java:490) at org.eclipse.jetty.util.Scanner.reportDifferences(Scanner.java:355) at org.eclipse.jetty.util.Scanner.scan(Scanner.java:306) at org.eclipse.jetty.util.Scanner$1.run(Scanner.java:258) at java.util.TimerThread.mainLoop(Timer.java:512) at java.util.TimerThread.run(Timer.java:462) 2010-05-26 15:32:12.907:WARN::Problem processing jar entry org/eclipse/jetty/util/MultiPartWriter.class java.io.IOException: Invalid resource at org.eclipse.jetty.util.resource.URLResource.getInputStream(URLResource.java:204) at org.eclipse.jetty.util.resource.JarResource.getInputStream(JarResource.java:113) at org.eclipse.jetty.annotations.AnnotationParser$2.processEntry(AnnotationParser.java:575) at org.eclipse.jetty.webapp.JarScanner.matched(JarScanner.java:152) at org.eclipse.jetty.util.PatternMatcher.matchPatterns(PatternMatcher.java:82) at org.eclipse.jetty.util.PatternMatcher.match(PatternMatcher.java:64) at org.eclipse.jetty.webapp.JarScanner.scan(JarScanner.java:75) at org.eclipse.jetty.annotations.AnnotationParser.parse(AnnotationParser.java:587) at org.eclipse.jetty.annotations.AbstractConfiguration.parseWebInfLib(AbstractConfiguration.java:107) at org.eclipse.jetty.annotations.AnnotationConfiguration.configure(AnnotationConfiguration.java:68) at org.eclipse.jetty.webapp.WebAppContext.startContext(WebAppContext.java:992) at org.eclipse.jetty.server.handler.ContextHandler.doStart(ContextHandler.java:579) at org.eclipse.jetty.webapp.WebAppContext.doStart(WebAppContext.java:381) at org.eclipse.jetty.util.component.AbstractLifeCycle.start(AbstractLifeCycle.java:55) at org.eclipse.jetty.deploy.bindings.StandardStarter.processBinding(StandardStarter.java:36) at org.eclipse.jetty.deploy.AppLifeCycle.runBindings(AppLifeCycle.java:182) at org.eclipse.jetty.deploy.DeploymentManager.requestAppGoal(DeploymentManager.java:497) at org.eclipse.jetty.deploy.DeploymentManager.addApp(DeploymentManager.java:135) at org.eclipse.jetty.deploy.providers.ScanningAppProvider$1.fileChanged(ScanningAppProvider.java:77) at org.eclipse.jetty.util.Scanner.reportChange(Scanner.java:490) at org.eclipse.jetty.util.Scanner.reportDifferences(Scanner.java:355) at org.eclipse.jetty.util.Scanner.scan(Scanner.java:306) at org.eclipse.jetty.util.Scanner$1.run(Scanner.java:258) at java.util.TimerThread.mainLoop(Timer.java:512) at java.util.TimerThread.run(Timer.java:462) 2010-05-26 15:32:12.907:WARN::Problem processing jar entry org/eclipse/jetty/util/Attributes.class java.io.IOException: Invalid resource at org.eclipse.jetty.util.resource.URLResource.getInputStream(URLResource.java:204) at org.eclipse.jetty.util.resource.JarResource.getInputStream(JarResource.java:113) at org.eclipse.jetty.annotations.AnnotationParser$2.processEntry(AnnotationParser.java:575) at org.eclipse.jetty.webapp.JarScanner.matched(JarScanner.java:152) at org.eclipse.jetty.util.PatternMatcher.matchPatterns(PatternMatcher.java:82) at org.eclipse.jetty.util.PatternMatcher.match(PatternMatcher.java:64) at org.eclipse.jetty.webapp.JarScanner.scan(JarScanner.java:75) at org.eclipse.jetty.annotations.AnnotationParser.parse(AnnotationParser.java:587) at org.eclipse.jetty.annotations.AbstractConfiguration.parseWebInfLib(AbstractConfiguration.java:107) at org.eclipse.jetty.annotations.AnnotationConfiguration.configure(AnnotationConfiguration.java:68) at org.eclipse.jetty.webapp.WebAppContext.startContext(WebAppContext.java:992) at org.eclipse.jetty.server.handler.ContextHandler.doStart(ContextHandler.java:579) at org.eclipse.jetty.webapp.WebAppContext.doStart(WebAppContext.java:381) at org.eclipse.jetty.util.component.AbstractLifeCycle.start(AbstractLifeCycle.java:55) at org.eclipse.jetty.deploy.bindings.StandardStarter.processBinding(StandardStarter.java:36) at org.eclipse.jetty.deploy.AppLifeCycle.runBindings(AppLifeCycle.java:182) at org.eclipse.jetty.deploy.DeploymentManager.requestAppGoal(DeploymentManager.java:497) at org.eclipse.jetty.deploy.DeploymentManager.addApp(DeploymentManager.java:135) at org.eclipse.jetty.deploy.providers.ScanningAppProvider$1.fileChanged(ScanningAppProvider.java:77) at org.eclipse.jetty.util.Scanner.reportChange(Scanner.java:490) at org.eclipse.jetty.util.Scanner.reportDifferences(Scanner.java:355) at org.eclipse.jetty.util.Scanner.scan(Scanner.java:306) at org.eclipse.jetty.util.Scanner$1.run(Scanner.java:258) at java.util.TimerThread.mainLoop(Timer.java:512) at java.util.TimerThread.run(Timer.java:462) Seemed to go through all the jetty binaries and complain about each class file. When I tried to deploy to 6.1.24 I got org.mortbay.util.MultiException[java.lang.NoClassDefFoundError: org/eclipse/jetty/util/ajax/JSON$Source, java.lang.NoClassDefFoundError: org/eclipse/jetty/util/thread/ThreadPool] at org.mortbay.jetty.servlet.ServletHandler.initialize(ServletHandler.java:656) at org.mortbay.jetty.servlet.Context.startContext(Context.java:140) at org.mortbay.jetty.webapp.WebAppContext.startContext(WebAppContext.java:1250) at org.mortbay.jetty.handler.ContextHandler.doStart(ContextHandler.java:517) at org.mortbay.jetty.webapp.WebAppContext.doStart(WebAppContext.java:467) at org.mortbay.component.AbstractLifeCycle.start(AbstractLifeCycle.java:50) at org.mortbay.jetty.handler.HandlerCollection.doStart(HandlerCollection.java:152) at org.mortbay.jetty.handler.ContextHandlerCollection.doStart(ContextHandlerCollection.java:156) at org.mortbay.component.AbstractLifeCycle.start(AbstractLifeCycle.java:50) at org.mortbay.jetty.handler.HandlerCollection.doStart(HandlerCollection.java:152) at org.mortbay.component.AbstractLifeCycle.start(AbstractLifeCycle.java:50) at org.mortbay.jetty.handler.HandlerWrapper.doStart(HandlerWrapper.java:130) at org.mortbay.jetty.Server.doStart(Server.java:224) at org.mortbay.component.AbstractLifeCycle.start(AbstractLifeCycle.java:50) at org.mortbay.xml.XmlConfiguration.main(XmlConfiguration.java:985) at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) at java.lang.reflect.Method.invoke(Method.java:597) at org.mortbay.start.Main.invokeMain(Main.java:194) at org.mortbay.start.Main.start(Main.java:534) at org.mortbay.start.Main.start(Main.java:441) at org.mortbay.start.Main.main(Main.java:119) My web.xml looks like this: <?xml version="1.0" encoding="UTF-8"?> <web-app xmlns="http://java.sun.com/xml/ns/javaee" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://java.sun.com/xml/ns/javaee http://java.sun.com/xml/ns/javaee/web-app_2_5.xsd" version="2.5"> <servlet> <servlet-name>cometd</servlet-name> <servlet-class>org.cometd.server.continuation.ContinuationCometdServlet</servlet-class> <load-on-startup>1</load-on-startup> </servlet> <servlet-mapping> <servlet-name>cometd</servlet-name> <url-pattern>/cometd/*</url-pattern> </servlet-mapping> <servlet> <servlet-name>initializer</servlet-name> <servlet-class>uk.co.dubit.nexus.comet.BayeuxInitializer</servlet-class> <load-on-startup>2</load-on-startup> </servlet> <!-- <filter> <filter-name>cross-origin</filter-name> <filter-class>org.eclipse.jetty.servlets.CrossOriginFilter</filter-class> </filter> <filter-mapping> <filter-name>cross-origin</filter-name> <url-pattern>/cometd/*</url-pattern> </filter-mapping> --> </web-app> note cross origin filter is commented out. The class didn't seem to exist when I tried to run on 6.1.24 (which as far as I understand is the correct behaviour, yes?). Sorry for the noob question but does anyone know what I'm doing wrong here? Regards, Tom

  Read the article

• How do I set the encoding statement in the XML declaration when performing an XSL transformation usi

  - by aspiehler

  I wrote a simple package installer in WinBatch that needs to update an XML file with information about the package contents. My first stab at it involved loading the file with Msxml2.DOMDocument, adding nodes and data as required, then saving the data back to disk. This worked well enough, except that it would not create tab and CR/LF whitespace in the new data. The solution I came up with was writing an XSL stylesheet that would recreate the XML file with whitespace added back in. I'm doing this by: loading the XSL file into an Msxml2.FreeThreadedDOMDocument object setting that object as the stylesheet property of an Msxml2.XSLTemplate object creating an XSL processor via Msxml2.XSLTemplate.createProcessor() setting my original Msxml2.DOMDocument as the input property of the XSL processor Calling transform() method of the XSL processor, and saving the output to a file. This works as for as reformatting the XML file with tabs and carriage returns, but my XML declaration comes out either as <?xml version="1.0"?> or <?xml version="1.0" encoding="UTF-16"?> depending on whether I used Msxml2.*.6.0 or Msxml2.* objects (a fall back if the system doesn't have 6.0). If the encoding is set to UTF-16, Msxml12.DOMDocument complains about trying to convert UTF-16 to 1-byte encoding the next time I run my package installer. I've tried creating and adding an XML declaration using both createProcessingInstruction() to both the XML and XSL DOM objects, but neither one seems to affect the output of the XSLTemplate processor. I've also set encoding to UTF-8 in the <xsl:output/> tag in my XSL file. Here is the relevant code in my Winbatch script: xmlDoc = ObjectCreate("Msxml2.DOMDocument.6.0") if !xmlDoc then xmlDoc = ObjectCreate("Msxml2.DOMDocument") xmlDoc.async = @FALSE xmlDoc.validateOnParse = @TRUE xmlDoc.resolveExternals = @TRUE xmlDoc.preserveWhiteSpace = @TRUE xmlDoc.setProperty("SelectionLanguge", "XPath") xmlDoc.setProperty("SelectionNamespaces", "xmlns:fns='http://www.abc.com/f_namespace'") xmlDoc.load(xml_file_path) xslStyleSheet = ObjectCreate("Msxml2.FreeThreadedDOMDocument.6.0") if !xslStyleSheet then xslStyleSheet = ObjectCreate("Msxml2.FreeThreadedDOMDocument") xslStyleSheet.async = @FALSE xslStyleSheet.validateOnParse = @TRUE xslStyleSheet.load(xsl_style_sheet_path) xslTemplate = ObjectCreate("Msxml2.XSLTemplate.6.0") if !xslTemplate then xslTemplate = ObjectCreate("Msxml2.XSLTemplate") xslTemplate.stylesheet = xslStyleSheet processor = xslTemplate.createProcessor() processor.input = xmlDoc processor.transform() ; create a new file and write the XML processor output to it fh = FileOpen(output_file_path, "WRITE" , @FALSE) FileWrite(fh, processor.output) FileClose(fh) The style sheet, with some slight changes to protect the innocent: <?xml version="1.0" encoding="UTF-8"?> <xsl:stylesheet xmlns:xsl="http://www.w3.org/1999/XSL/Transform" version="1.1"> <xsl:output method="xml" indent="yes" encoding="UTF-8"/> <xsl:template match="/"> <fns:test_station xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:fns="http://www.abc.com/f_namespace"> <xsl:for-each select="/fns:test_station/identification"> <xsl:text>&#x0A; </xsl:text> <identification> <xsl:for-each select="./*"> <xsl:text>&#x0A; </xsl:text> <xsl:copy-of select="."/> </xsl:for-each> <xsl:text>&#x0A; </xsl:text> </identification> </xsl:for-each> <xsl:for-each select="/fns:test_station/software"> <xsl:text>&#x0A; </xsl:text> <software> <xsl:for-each select="./package"> <xsl:text>&#x0A; </xsl:text> <package> <xsl:for-each select="./*"> <xsl:text>&#x0A; </xsl:text> <xsl:copy-of select="."/> </xsl:for-each> <xsl:text>&#x0A; </xsl:text> </package> </xsl:for-each> <xsl:text>&#x0A; </xsl:text> </software> </xsl:for-each> <xsl:for-each select="/fns:test_station/calibration"> <xsl:text>&#x0A; </xsl:text> <calibration> <xsl:for-each select="./item"> <xsl:text>&#x0A; </xsl:text> <item> <xsl:for-each select="./*"> <xsl:text>&#x0A; </xsl:text> <xsl:copy-of select="."/> </xsl:for-each> <xsl:text>&#x0A; </xsl:text> </item> </xsl:for-each> <xsl:text>&#x0A; </xsl:text> </calibration> </xsl:for-each> </fns:test_station> </xsl:template> </xsl:stylesheet> And this is a sample output file: <?xml version="1.0" encoding="UTF-16"?> <fns:test_station xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:fns="http://www.abc.com/f_namespace"> <software> <package> <part_number>123456789</part_number> <version>00</version> <test_category>1</test_category> <description>name of software package</description> <execution_path>c:\program files\test\test.exe</execution_path> <execution_arguments>arguments</execution_arguments> <crc_path>c:\ste_config\crc\123456789.lst</crc_path> <uninstall_path>c:\ste_config\uninstall\uninst_123456789.bat</uninstall_path> <install_timestamp>2009-11-09T14:00:44</install_timestamp> </package> </software> </fns:test_station>

  Read the article

• Hibernate/Spring: failed to lazily initialize - no session or session was closed

  - by Niko

  I know something similar has been asked already, but unfortunately I wasn't able to find a reliable answer - even with searching for over 2 days. The basic problem is the same as asked multiple time. I have a simple program with two POJOs Event and User - where a user can have multiple events. @Entity @Table public class Event { private Long id; private String name; private User user; @Column @Id @GeneratedValue public Long getId() {return id;} public void setId(Long id) { this.id = id; } @Column public String getName() {return name;} public void setName(String name) {this.name = name;} @ManyToOne @JoinColumn(name="user_id") public User getUser() {return user;} public void setUser(User user) {this.user = user;} } @Entity @Table public class User { private Long id; private String name; private List events; @Column @Id @GeneratedValue public Long getId() { return id; } public void setId(Long id) { this.id = id; } @Column public String getName() { return name; } public void setName(String name) { this.name = name; } @OneToMany(mappedBy="user", fetch=FetchType.LAZY) public List getEvents() { return events; } public void setEvents(List events) { this.events = events; } } Note: This is a sample project. I really want to use Lazy fetching here. I use spring and hibernate and have a simple basic-db.xml for loading: <?xml version="1.0" encoding="UTF-8"? <beans xmlns="http://www.springframework.org/schema/beans" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:aop="http://www.springframework.org/schema/aop" xsi:schemaLocation="http://www.springframework.org/schema/beans http://www.springframework.org/schema/beans/spring-beans-3.0.xsd http://www.springframework.org/schema/aop http://www.springframework.org/schema/aop/spring-aop-3.0.xsd" <bean id="myDataSource" class="org.apache.commons.dbcp.BasicDataSource" destroy-method="close" scope="thread" <property name="driverClassName" value="com.mysql.jdbc.Driver" / <property name="url" value="jdbc:mysql://192.168.1.34:3306/hibernateTest" / <property name="username" value="root" / <property name="password" value="" / <aop:scoped-proxy/ </bean <bean class="org.springframework.beans.factory.config.CustomScopeConfigurer" <property name="scopes" <map <entry key="thread" <bean class="org.springframework.context.support.SimpleThreadScope" / </entry </map </property </bean <bean id="mySessionFactory" class="org.springframework.orm.hibernate3.annotation.AnnotationSessionFactoryBean" scope="thread" <property name="dataSource" ref="myDataSource" / <property name="annotatedClasses" <list <valuedata.model.User</value <valuedata.model.Event</value </list </property <property name="hibernateProperties" <props <prop key="hibernate.dialect"org.hibernate.dialect.MySQLDialect</prop <prop key="hibernate.show_sql"true</prop <prop key="hibernate.hbm2ddl.auto"create</prop </props </property <aop:scoped-proxy/ </bean <bean id="myUserDAO" class="data.dao.impl.UserDaoImpl" <property name="sessionFactory" ref="mySessionFactory" / </bean <bean id="myEventDAO" class="data.dao.impl.EventDaoImpl" <property name="sessionFactory" ref="mySessionFactory" / </bean </beans Note: I played around with the CustomScopeConfigurer and SimpleThreadScope, but that didnt change anything. I have a simple dao-impl (only pasting the userDao - the EventDao is pretty much the same - except with out the "listWith" function: public class UserDaoImpl implements UserDao{ private HibernateTemplate hibernateTemplate; public void setSessionFactory(SessionFactory sessionFactory) { this.hibernateTemplate = new HibernateTemplate(sessionFactory); } @SuppressWarnings("unchecked") @Override public List listUser() { return hibernateTemplate.find("from User"); } @Override public void saveUser(User user) { hibernateTemplate.saveOrUpdate(user); } @Override public List listUserWithEvent() { List users = hibernateTemplate.find("from User"); for (User user : users) { System.out.println("LIST : " + user.getName() + ":"); user.getEvents().size(); } return users; } } I am getting the org.hibernate.LazyInitializationException - failed to lazily initialize a collection of role: data.model.User.events, no session or session was closed at the line with user.getEvents().size(); And last but not least here is the Test class I use: public class HibernateTest { public static void main(String[] args) { ClassPathXmlApplicationContext ac = new ClassPathXmlApplicationContext("basic-db.xml"); UserDao udao = (UserDao) ac.getBean("myUserDAO"); EventDao edao = (EventDao) ac.getBean("myEventDAO"); System.out.println("New user..."); User user = new User(); user.setName("test"); Event event1 = new Event(); event1.setName("Birthday1"); event1.setUser(user); Event event2 = new Event(); event2.setName("Birthday2"); event2.setUser(user); udao.saveUser(user); edao.saveEvent(event1); edao.saveEvent(event2); List users = udao.listUserWithEvent(); System.out.println("Events for users"); for (User u : users) { System.out.println(u.getId() + ":" + u.getName() + " --"); for (Event e : u.getEvents()) { System.out.println("\t" + e.getId() + ":" + e.getName()); } } ((ConfigurableApplicationContext)ac).close(); } } and here is the Exception I get: 1621 [main] ERROR org.hibernate.LazyInitializationException - failed to lazily initialize a collection of role: data.model.User.events, no session or session was closed org.hibernate.LazyInitializationException: failed to lazily initialize a collection of role: data.model.User.events, no session or session was closed at org.hibernate.collection.AbstractPersistentCollection.throwLazyInitializationException(AbstractPersistentCollection.java:380) at org.hibernate.collection.AbstractPersistentCollection.throwLazyInitializationExceptionIfNotConnected(AbstractPersistentCollection.java:372) at org.hibernate.collection.AbstractPersistentCollection.readSize(AbstractPersistentCollection.java:119) at org.hibernate.collection.PersistentBag.size(PersistentBag.java:248) at data.dao.impl.UserDaoImpl.listUserWithEvent(UserDaoImpl.java:38) at HibernateTest.main(HibernateTest.java:44) Exception in thread "main" org.hibernate.LazyInitializationException: failed to lazily initialize a collection of role: data.model.User.events, no session or session was closed at org.hibernate.collection.AbstractPersistentCollection.throwLazyInitializationException(AbstractPersistentCollection.java:380) at org.hibernate.collection.AbstractPersistentCollection.throwLazyInitializationExceptionIfNotConnected(AbstractPersistentCollection.java:372) at org.hibernate.collection.AbstractPersistentCollection.readSize(AbstractPersistentCollection.java:119) at org.hibernate.collection.PersistentBag.size(PersistentBag.java:248) at data.dao.impl.UserDaoImpl.listUserWithEvent(UserDaoImpl.java:38) at HibernateTest.main(HibernateTest.java:44) Things I tried but did not work: assign a threadScope and using beanfactory (I used "request" or "thread" - no difference noticed): // scope stuff Scope threadScope = new SimpleThreadScope(); ConfigurableListableBeanFactory beanFactory = ac.getBeanFactory(); beanFactory.registerScope("request", threadScope); ac.refresh(); ... Setting up a transaction by getting the session object from the deo: ... Transaction tx = ((UserDaoImpl)udao).getSession().beginTransaction(); tx.begin(); users = udao.listUserWithEvent(); ... getting a transaction within the listUserWithEvent() public List listUserWithEvent() { SessionFactory sf = hibernateTemplate.getSessionFactory(); Session s = sf.openSession(); Transaction tx = s.beginTransaction(); tx.begin(); List users = hibernateTemplate.find("from User"); for (User user : users) { System.out.println("LIST : " + user.getName() + ":"); user.getEvents().size(); } tx.commit(); return users; } I am really out of ideas by now. Also, using the listUser or listEvent just work fine.

  Read the article

• AngularJS on top of ASP.NET: Moving the MVC framework out to the browser

  - by Varun Chatterji

  Heavily drawing inspiration from Ruby on Rails, MVC4’s convention over configuration model of development soon became the Holy Grail of .NET web development. The MVC model brought with it the goodness of proper separation of concerns between business logic, data, and the presentation logic. However, the MVC paradigm, was still one in which server side .NET code could be mixed with presentation code. The Razor templating engine, though cleaner than its predecessors, still encouraged and allowed you to mix .NET server side code with presentation logic. Thus, for example, if the developer required a certain <div> tag to be shown if a particular variable ShowDiv was true in the View’s model, the code could look like the following: Fig 1: To show a div or not. Server side .NET code is used in the View Mixing .NET code with HTML in views can soon get very messy. Wouldn’t it be nice if the presentation layer (HTML) could be pure HTML? Also, in the ASP.NET MVC model, some of the business logic invariably resides in the controller. It is tempting to use an anti­pattern like the one shown above to control whether a div should be shown or not. However, best practice would indicate that the Controller should not be aware of the div. The ShowDiv variable in the model should not exist. A controller should ideally, only be used to do the plumbing of getting the data populated in the model and nothing else. The view (ideally pure HTML) should render the presentation layer based on the model. In this article we will see how Angular JS, a new JavaScript framework by Google can be used effectively to build web applications where: 1. Views are pure HTML 2. Controllers (in the server sense) are pure REST based API calls 3. The presentation layer is loaded as needed from partial HTML only files. What is MVVM? MVVM short for Model View View Model is a new paradigm in web development. In this paradigm, the Model and View stuff exists on the client side through javascript instead of being processed on the server through postbacks. These frameworks are JavaScript frameworks that facilitate the clear separation of the “frontend” or the data rendering logic from the “backend” which is typically just a REST based API that loads and processes data through a resource model. The frameworks are called MVVM as a change to the Model (through javascript) gets reflected in the view immediately i.e. Model > View. Also, a change on the view (through manual input) gets reflected in the model immediately i.e. View > Model. The following figure shows this conceptually (comments are shown in red): Fig 2: Demonstration of MVVM in action In Fig 2, two text boxes are bound to the same variable model.myInt. Thus, changing the view manually (changing one text box through keyboard input) also changes the other textbox in real time demonstrating V > M property of a MVVM framework. Furthermore, clicking the button adds 1 to the value of model.myInt thus changing the model through JavaScript. This immediately updates the view (the value in the two textboxes) thus demonstrating the M > V property of a MVVM framework. Thus we see that the model in a MVVM JavaScript framework can be regarded as “the single source of truth“. This is an important concept. Angular is one such MVVM framework. We shall use it to build a simple app that sends SMS messages to a particular number. Application, Routes, Views, Controllers, Scope and Models Angular can be used in many ways to construct web applications. For this article, we shall only focus on building Single Page Applications (SPAs). Many of the approaches we will follow in this article have alternatives. It is beyond the scope of this article to explain every nuance in detail but we shall try to touch upon the basic concepts and end up with a working application that can be used to send SMS messages using Sent.ly Plus (a service that is itself built using Angular). Before you read on, we would like to urge you to forget what you know about Models, Views, Controllers and Routes in the ASP.NET MVC4 framework. All these words have different meanings in the Angular world. Whenever these words are used in this article, they will refer to Angular concepts and not ASP.NET MVC4 concepts. The following figure shows the skeleton of the root page of an SPA: Fig 3: The skeleton of a SPA The skeleton of the application is based on the Bootstrap starter template which can be found at: http://getbootstrap.com/examples/starter­template/ Apart from loading the Angular, jQuery and Bootstrap JavaScript libraries, it also loads our custom scripts /app/js/controllers.js /app/js/app.js These scripts define the routes, views and controllers which we shall come to in a moment. Application Notice that the body tag (Fig. 3) has an extra attribute: ng­app=”smsApp” Providing this tag “bootstraps” our single page application. It tells Angular to load a “module” called smsApp. This “module” is defined /app/js/app.js angular.module('smsApp', ['smsApp.controllers', function () {}]) Fig 4: The definition of our application module The line shows above, declares a module called smsApp. It also declares that this module “depends” on another module called “smsApp.controllers”. The smsApp.controllers module will contain all the controllers for our SPA. Routing and Views Notice that in the Navbar (in Fig 3) we have included two hyperlinks to: “#/app” “#/help” This is how Angular handles routing. Since the URLs start with “#”, they are actually just bookmarks (and not server side resources). However, our route definition (in /app/js/app.js) gives these URLs a special meaning within the Angular framework. angular.module('smsApp', ['smsApp.controllers', function () { }]) //Configure the routes .config(['$routeProvider', function ($routeProvider) { $routeProvider.when('/binding', { templateUrl: '/app/partials/bindingexample.html', controller: 'BindingController' }); }]); Fig 5: The definition of a route with an associated partial view and controller As we can see from the previous code sample, we are using the $routeProvider object in the configuration of our smsApp module. Notice how the code “asks for” the $routeProvider object by specifying it as a dependency in the [] braces and then defining a function that accepts it as a parameter. This is known as dependency injection. Please refer to the following link if you want to delve into this topic: http://docs.angularjs.org/guide/di What the above code snippet is doing is that it is telling Angular that when the URL is “#/binding”, then it should load the HTML snippet (“partial view”) found at /app/partials/bindingexample.html. Also, for this URL, Angular should load the controller called “BindingController”. We have also marked the div with the class “container” (in Fig 3) with the ng­view attribute. This attribute tells Angular that views (partial HTML pages) defined in the routes will be loaded within this div. You can see that the Angular JavaScript framework, unlike many other frameworks, works purely by extending HTML tags and attributes. It also allows you to extend HTML with your own tags and attributes (through directives) if you so desire, you can find out more about directives at the following URL: http://www.codeproject.com/Articles/607873/Extending­HTML­with­AngularJS­Directives Controllers and Models We have seen how we define what views and controllers should be loaded for a particular route. Let us now consider how controllers are defined. Our controllers are defined in the file /app/js/controllers.js. The following snippet shows the definition of the “BindingController” which is loaded when we hit the URL http://localhost:port/index.html#/binding (as we have defined in the route earlier as shown in Fig 5). Remember that we had defined that our application module “smsApp” depends on the “smsApp.controllers” module (see Fig 4). The code snippet below shows how the “BindingController” defined in the route shown in Fig 5 is defined in the module smsApp.controllers: angular.module('smsApp.controllers', [function () { }]) .controller('BindingController', ['$scope', function ($scope) { $scope.model = {}; $scope.model.myInt = 6; $scope.addOne = function () { $scope.model.myInt++; } }]); Fig 6: The definition of a controller in the “smsApp.controllers” module. The pieces are falling in place! Remember Fig.2? That was the code of a partial view that was loaded within the container div of the skeleton SPA shown in Fig 3. The route definition shown in Fig 5 also defined that the controller called “BindingController” (shown in Fig 6.) was loaded when we loaded the URL: http://localhost:22544/index.html#/binding The button in Fig 2 was marked with the attribute ng­click=”addOne()” which added 1 to the value of model.myInt. In Fig 6, we can see that this function is actually defined in the “BindingController”. Scope We can see from Fig 6, that in the definition of “BindingController”, we defined a dependency on $scope and then, as usual, defined a function which “asks for” $scope as per the dependency injection pattern. So what is $scope? Any guesses? As you might have guessed a scope is a particular “address space” where variables and functions may be defined. This has a similar meaning to scope in a programming language like C#. Model: The Scope is not the Model It is tempting to assign variables in the scope directly. For example, we could have defined myInt as $scope.myInt = 6 in Fig 6 instead of $scope.model.myInt = 6. The reason why this is a bad idea is that scope in hierarchical in Angular. Thus if we were to define a controller which was defined within the another controller (nested controllers), then the inner controller would inherit the scope of the parent controller. This inheritance would follow JavaScript prototypal inheritance. Let’s say the parent controller defined a variable through $scope.myInt = 6. The child controller would inherit the scope through java prototypical inheritance. This basically means that the child scope has a variable myInt that points to the parent scopes myInt variable. Now if we assigned the value of myInt in the parent, the child scope would be updated with the same value as the child scope’s myInt variable points to the parent scope’s myInt variable. However, if we were to assign the value of the myInt variable in the child scope, then the link of that variable to the parent scope would be broken as the variable myInt in the child scope now points to the value 6 and not to the parent scope’s myInt variable. But, if we defined a variable model in the parent scope, then the child scope will also have a variable model that points to the model variable in the parent scope. Updating the value of $scope.model.myInt in the parent scope would change the model variable in the child scope too as the variable is pointed to the model variable in the parent scope. Now changing the value of $scope.model.myInt in the child scope would ALSO change the value in the parent scope. This is because the model reference in the child scope is pointed to the scope variable in the parent. We did no new assignment to the model variable in the child scope. We only changed an attribute of the model variable. Since the model variable (in the child scope) points to the model variable in the parent scope, we have successfully changed the value of myInt in the parent scope. Thus the value of $scope.model.myInt in the parent scope becomes the “single source of truth“. This is a tricky concept, thus it is considered good practice to NOT use scope inheritance. More info on prototypal inheritance in Angular can be found in the “JavaScript Prototypal Inheritance” section at the following URL: https://github.com/angular/angular.js/wiki/Understanding­Scopes. Building It: An Angular JS application using a .NET Web API Backend Now that we have a perspective on the basic components of an MVVM application built using Angular, let’s build something useful. We will build an application that can be used to send out SMS messages to a given phone number. The following diagram describes the architecture of the application we are going to build: Fig 7: Broad application architecture We are going to add an HTML Partial to our project. This partial will contain the form fields that will accept the phone number and message that needs to be sent as an SMS. It will also display all the messages that have previously been sent. All the executable code that is run on the occurrence of events (button clicks etc.) in the view resides in the controller. The controller interacts with the ASP.NET WebAPI to get a history of SMS messages, add a message etc. through a REST based API. For the purposes of simplicity, we will use an in memory data structure for the purposes of creating this application. Thus, the tasks ahead of us are: Creating the REST WebApi with GET, PUT, POST, DELETE methods. Creating the SmsView.html partial Creating the SmsController controller with methods that are called from the SmsView.html partial Add a new route that loads the controller and the partial. 1. Creating the REST WebAPI This is a simple task that should be quite straightforward to any .NET developer. The following listing shows our ApiController: public class SmsMessage { public string to { get; set; } public string message { get; set; } } public class SmsResource : SmsMessage { public int smsId { get; set; } } public class SmsResourceController : ApiController { public static Dictionary<int, SmsResource> messages = new Dictionary<int, SmsResource>(); public static int currentId = 0; // GET api/<controller> public List<SmsResource> Get() { List<SmsResource> result = new List<SmsResource>(); foreach (int key in messages.Keys) { result.Add(messages[key]); } return result; } // GET api/<controller>/5 public SmsResource Get(int id) { if (messages.ContainsKey(id)) return messages[id]; return null; } // POST api/<controller> public List<SmsResource> Post([FromBody] SmsMessage value) { //Synchronize on messages so we don't have id collisions lock (messages) { SmsResource res = (SmsResource) value; res.smsId = currentId++; messages.Add(res.smsId, res); //SentlyPlusSmsSender.SendMessage(value.to, value.message); return Get(); } } // PUT api/<controller>/5 public List<SmsResource> Put(int id, [FromBody] SmsMessage value) { //Synchronize on messages so we don't have id collisions lock (messages) { if (messages.ContainsKey(id)) { //Update the message messages[id].message = value.message; messages[id].to = value.message; } return Get(); } } // DELETE api/<controller>/5 public List<SmsResource> Delete(int id) { if (messages.ContainsKey(id)) { messages.Remove(id); } return Get(); } } Once this class is defined, we should be able to access the WebAPI by a simple GET request using the browser: http://localhost:port/api/SmsResource Notice the commented line: //SentlyPlusSmsSender.SendMessage The SentlyPlusSmsSender class is defined in the attached solution. We have shown this line as commented as we want to explain the core Angular concepts. If you load the attached solution, this line is uncommented in the source and an actual SMS will be sent! By default, the API returns XML. For consumption of the API in Angular, we would like it to return JSON. To change the default to JSON, we make the following change to WebApiConfig.cs file located in the App_Start folder. public static class WebApiConfig { public static void Register(HttpConfiguration config) { config.Routes.MapHttpRoute( name: "DefaultApi", routeTemplate: "api/{controller}/{id}", defaults: new { id = RouteParameter.Optional } ); var appXmlType = config.Formatters.XmlFormatter. SupportedMediaTypes. FirstOrDefault( t => t.MediaType == "application/xml"); config.Formatters.XmlFormatter.SupportedMediaTypes.Remove(appXmlType); } } We now have our backend REST Api which we can consume from Angular! 2. Creating the SmsView.html partial This simple partial will define two fields: the destination phone number (international format starting with a +) and the message. These fields will be bound to model.phoneNumber and model.message. We will also add a button that we shall hook up to sendMessage() in the controller. A list of all previously sent messages (bound to model.allMessages) will also be displayed below the form input. The following code shows the code for the partial: <!--­­ If model.errorMessage is defined, then render the error div -­­> <div class="alert alert-­danger alert-­dismissable" style="margin­-top: 30px;" ng­-show="model.errorMessage != undefined"> <button type="button" class="close" data­dismiss="alert" aria­hidden="true">&times;</button> <strong>Error!</strong> <br /> {{ model.errorMessage }} </div> <!--­­ The input fields bound to the model --­­> <div class="well" style="margin-­top: 30px;"> <table style="width: 100%;"> <tr> <td style="width: 45%; text-­align: center;"> <input type="text" placeholder="Phone number (eg; +44 7778 609466)" ng­-model="model.phoneNumber" class="form-­control" style="width: 90%" onkeypress="return checkPhoneInput();" /> </td> <td style="width: 45%; text-­align: center;"> <input type="text" placeholder="Message" ng­-model="model.message" class="form-­control" style="width: 90%" /> </td> <td style="text-­align: center;"> <button class="btn btn-­danger" ng-­click="sendMessage();" ng-­disabled="model.isAjaxInProgress" style="margin­right: 5px;">Send</button> <img src="/Content/ajax-­loader.gif" ng­-show="model.isAjaxInProgress" /> </td> </tr> </table> </div> <!--­­ The past messages ­­--> <div style="margin-­top: 30px;"> <!­­-- The following div is shown if there are no past messages --­­> <div ng­-show="model.allMessages.length == 0"> No messages have been sent yet! </div> <!--­­ The following div is shown if there are some past messages --­­> <div ng-­show="model.allMessages.length == 0"> <table style="width: 100%;" class="table table-­striped"> <tr> <td>Phone Number</td> <td>Message</td> <td></td> </tr> <!--­­ The ng-­repeat directive is line the repeater control in .NET, but as you can see this partial is pure HTML which is much cleaner --> <tr ng-­repeat="message in model.allMessages"> <td>{{ message.to }}</td> <td>{{ message.message }}</td> <td> <button class="btn btn-­danger" ng-­click="delete(message.smsId);" ng­-disabled="model.isAjaxInProgress">Delete</button> </td> </tr> </table> </div> </div> The above code is commented and should be self explanatory. Conditional rendering is achieved through using the ng-­show=”condition” attribute on various div tags. Input fields are bound to the model and the send button is bound to the sendMessage() function in the controller as through the ng­click=”sendMessage()” attribute defined on the button tag. While AJAX calls are taking place, the controller sets model.isAjaxInProgress to true. Based on this variable, buttons are disabled through the ng-­disabled directive which is added as an attribute to the buttons. The ng-­repeat directive added as an attribute to the tr tag causes the table row to be rendered multiple times much like an ASP.NET repeater. 3. Creating the SmsController controller The penultimate piece of our application is the controller which responds to events from our view and interacts with our MVC4 REST WebAPI. The following listing shows the code we need to add to /app/js/controllers.js. Note that controller definitions can be chained. Also note that this controller “asks for” the $http service. The $http service is a simple way in Angular to do AJAX. So far we have only encountered modules, controllers, views and directives in Angular. The $http is new entity in Angular called a service. More information on Angular services can be found at the following URL: http://docs.angularjs.org/guide/dev_guide.services.understanding_services. .controller('SmsController', ['$scope', '$http', function ($scope, $http) { //We define the model $scope.model = {}; //We define the allMessages array in the model //that will contain all the messages sent so far $scope.model.allMessages = []; //The error if any $scope.model.errorMessage = undefined; //We initially load data so set the isAjaxInProgress = true; $scope.model.isAjaxInProgress = true; //Load all the messages $http({ url: '/api/smsresource', method: "GET" }). success(function (data, status, headers, config) { this callback will be called asynchronously //when the response is available $scope.model.allMessages = data; //We are done with AJAX loading $scope.model.isAjaxInProgress = false; }). error(function (data, status, headers, config) { //called asynchronously if an error occurs //or server returns response with an error status. $scope.model.errorMessage = "Error occurred status:" + status; //We are done with AJAX loading $scope.model.isAjaxInProgress = false; }); $scope.delete = function (id) { //We are making an ajax call so we set this to true $scope.model.isAjaxInProgress = true; $http({ url: '/api/smsresource/' + id, method: "DELETE" }). success(function (data, status, headers, config) { // this callback will be called asynchronously // when the response is available $scope.model.allMessages = data; //We are done with AJAX loading $scope.model.isAjaxInProgress = false; }); error(function (data, status, headers, config) { // called asynchronously if an error occurs // or server returns response with an error status. $scope.model.errorMessage = "Error occurred status:" + status; //We are done with AJAX loading $scope.model.isAjaxInProgress = false; }); } $scope.sendMessage = function () { $scope.model.errorMessage = undefined; var message = ''; if($scope.model.message != undefined) message = $scope.model.message.trim(); if ($scope.model.phoneNumber == undefined || $scope.model.phoneNumber == '' || $scope.model.phoneNumber.length < 10 || $scope.model.phoneNumber[0] != '+') { $scope.model.errorMessage = "You must enter a valid phone number in international format. Eg: +44 7778 609466"; return; } if (message.length == 0) { $scope.model.errorMessage = "You must specify a message!"; return; } //We are making an ajax call so we set this to true $scope.model.isAjaxInProgress = true; $http({ url: '/api/smsresource', method: "POST", data: { to: $scope.model.phoneNumber, message: $scope.model.message } }). success(function (data, status, headers, config) { // this callback will be called asynchronously // when the response is available $scope.model.allMessages = data; //We are done with AJAX loading $scope.model.isAjaxInProgress = false; }). error(function (data, status, headers, config) { // called asynchronously if an error occurs // or server returns response with an error status. $scope.model.errorMessage = "Error occurred status:" + status // We are done with AJAX loading $scope.model.isAjaxInProgress = false; }); } }]); We can see from the previous listing how the functions that are called from the view are defined in the controller. It should also be evident how easy it is to make AJAX calls to consume our MVC4 REST WebAPI. Now we are left with the final piece. We need to define a route that associates a particular path with the view we have defined and the controller we have defined. 4. Add a new route that loads the controller and the partial This is the easiest part of the puzzle. We simply define another route in the /app/js/app.js file: $routeProvider.when('/sms', { templateUrl: '/app/partials/smsview.html', controller: 'SmsController' }); Conclusion In this article we have seen how much of the server side functionality in the MVC4 framework can be moved to the browser thus delivering a snappy and fast user interface. We have seen how we can build client side HTML only views that avoid the messy syntax offered by server side Razor views. We have built a functioning app from the ground up. The significant advantage of this approach to building web apps is that the front end can be completely platform independent. Even though we used ASP.NET to create our REST API, we could just easily have used any other language such as Node.js, Ruby etc without changing a single line of our front end code. Angular is a rich framework and we have only touched on basic functionality required to create a SPA. For readers who wish to delve further into the Angular framework, we would recommend the following URL as a starting point: http://docs.angularjs.org/misc/started. To get started with the code for this project: Sign up for an account at http://plus.sent.ly (free) Add your phone number Go to the “My Identies Page” Note Down your Sender ID, Consumer Key and Consumer Secret Download the code for this article at: https://docs.google.com/file/d/0BzjEWqSE31yoZjZlV0d0R2Y3eW8/edit?usp=sharing Change the values of Sender Id, Consumer Key and Consumer Secret in the web.config file Run the project through Visual Studio!

  Read the article

< Previous Page | 501 502 503 504 505 506 507 508 509  | Next Page >