Search Results

Search found 35244 results on 1410 pages for 'version numbers'.

Page 506/1410 | < Previous Page | 502 503 504 505 506 507 508 509 510 511 512 513  | Next Page >

• Degraded RAID5 and no md superblock on one of remaining drive

  - by ark1214

  This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

  Read the article

• warning: dict_ldap_lookup: Search error 1: Operations error

  - by drecute

  Please I need help with ldap search filter to use to retrieve the user email information from ldap. I'm running postfix_ldap of Ubuntu server 12.04. Everything seems to work fine, except getting the values returned from the search. Version 1 server_host = ldap://samba.example.com search_base = dc=company, dc=example, dc=com query_filter = mail=%s bind = no domain = example.com Version 2 server_host = ldap://samba.example.com search_base = dc=company, dc=example, dc=com query_filter = mail=%s bind_dn = cn=Users,dc=company,dc=example,dc=com domain = example.com mail logs Nov 26 11:13:26 mail postfix/smtpd[19662]: match_string: example.com ~? example.com Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_lookup: No existing connection for LDAP source /etc/postfix/ldap-aliases.cf, reopening Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Connecting to server ldap://samba.example.com Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Actual Protocol version used is 3. Nov 26 11:13:26 mail postfix/smtpd[19662]: dict_ldap_connect: Binding to server ldap://samba.example.com with dn cn=Users,dc=company,dc=example,dc=com Nov 26 11:13:26 mail postfix/smtpd[19662]: warning: dict_ldap_connect: Unable to bind to server ldap://samba.example.com with dn cn=Users,dc=company,dc=example,dc=com: 49 (Invalid credentials) Nov 26 11:13:26 mail postfix/smtpd[19662]: warning: ldap:/etc/postfix/ldap-aliases.cf lookup error for "[email protected]" Nov 26 11:13:26 mail postfix/smtpd[19662]: maps_find: virtual_alias_maps: [email protected]: search aborted Nov 26 11:13:26 mail postfix/smtpd[19662]: mail_addr_find: [email protected] -> (try again) Nov 26 11:13:26 mail postfix/smtpd[19662]: NOQUEUE: reject: RCPT from col0-omc3-s2.col0.hotmail.com[65.55.34.140]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<col0-omc3-s2.col0.hotmail.com> Nov 26 11:13:26 mail postfix/smtpd[19662]: > col0-omc3-s2.col0.hotmail.com[65.55.34.140]: 451 4.3.0 <[email protected]>: Temporary lookup failure here's another log with successful search result but fialed to get the values of the result Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: Using existing connection for LDAP source /etc/postfix/ldap-aliases.cf Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Searching with filter [email protected] Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_get_values[1]: Search found 1 match(es) Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_get_values[1]: Leaving dict_ldap_get_values Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: Search returned nothing Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: [email protected]: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: In dict_ldap_lookup Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Skipping lookup of key 'tola.akintola': domain mismatch Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: tola.akintola: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: In dict_ldap_lookup Nov 26 12:04:56 mail postfix/smtpd[20463]: dict_ldap_lookup: /etc/postfix/ldap-aliases.cf: Skipping lookup of key '@example.com': domain mismatch Nov 26 12:04:56 mail postfix/smtpd[20463]: maps_find: virtual_alias_maps: @example.com: not found Nov 26 12:04:56 mail postfix/smtpd[20463]: mail_addr_find: [email protected] -> (not found) My refined ldap-aliases.cf looks like this: server_host = ldap://samba.example.com server_port = 3268 search_base = dc=company, dc=example, dc=com query_filter = mail=%s result_attribute = uid bind_dn = cn=Administrator,cn=Users,dc=company,dc=example,dc=com bind_pw = pass domain = example.com So I'll like to know what ldap filter is appropriate to get this to work. Thanks for helping out.

  Read the article

• Dual head setup for Ubuntu 10.04.1 and Windows XP Pro with same hardware configuration

  - by mejpark

  I have a Dell OptiPlex 360 workstation at work, with 2 x ATI RV280 [Radeon 9200 PRO] graphics cards installed, which are attached to two identical 19" HII flat panel monitors. I'm using the open source Radeon driver with Ubuntu, and the proprietary drivers with Windows. The good news is that dual head configuration works for both OSes. The bad news is, I have to use a different hardware configuration for each OS to achieve this. Hardware config #1: Dual monitors work for Windows XP Pro like this: First display -> external VGA port Second display -> DVI input on gfx card Hardware config #2: Dual monitors work for Ubuntu 10.04.1 like this: First display -> VGA port on gfx card Second display -> DVI input on gfx card I connected up the displays according to Config #2 and booted up Windows, which resulted in a mirror image on both screens. I was unable to login, as the login box was not visible. I unplugged the VGA lead from gfx card and plugged it into the external VGA port (Config #1) - Windows dual head works again, but the VGA-connected screen is not recognised by Ubuntu and remains in standby mode. Is it possible to configure a dual head setup for Ubuntu using Config #1, or am I missing something? I tried setting up dual monitors using Config #1, this morning which didn't work. By default, there is no xorg.conf file in Ubuntu 10.04.1, so I generated one using: $ sudo X :2 -configure X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux harrier 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=a34c1931-98d4-4a34-880c-c227a2936c4a ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.2.log", Time: Mon Sep 13 10:02:02 2010 List of video drivers: apm ark intel mach64 s3virge trident mga tseng ati nouveau neomagic i740 openchrome voodoo s3 i128 radeon siliconmotion nv ztv vmware v4l chips rendition savage sisusb tdfx geode sis r128 cirrus fbdev vesa (++) Using config file: "/home/michael/xorg.conf.new" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (II) [KMS] No DRICreatePCIBusID symbol, no kernel modesetting. Xorg detected your mouse at device /dev/input/mice. Please check your config if the mouse is still not operational, as by default Xorg tries to autodetect the protocol. Xorg has configured a multihead system, please check your config. Your xorg.conf file is /home/michael/xorg.conf.new To test the server, run 'X -config /home/michael/xorg.conf.new' ddxSigGiveUp: Closing log $ sudo X -config /home/michael/xorg.conf.new Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again. Please consult the The X.Org Foundation support at http://wiki.x.org for help. ddxSigGiveUp: Closing log I then booted Ubuntu in failsafe mode, dropped into root shell, and executed $ X -config /home/michael/xorg.conf.new again. The screen went blank and turned off, so

  Read the article

• Installing Mod-wsgi 3.3 for apache 2.2 and python 3.2

  - by aaronasterling

  I am attempting to install Mod-wsgi 3.3 on an ubuntu 11.10 desktop edition with apache 2.2 and python 3.2 I downloaded the source tarball and extracted it. I configured it using the --with-python=/usr/bin/python3 option to configure. This is the only copy of python3 that I have installed. I then issued the commands make and sudo make install. I attempted to restart apache using sudo /etc/init.d/apache2 restart and get the following error message: apache2: Syntax error on line 203 of /etc/apache2/apache2.conf: Syntax error on line 1 of /etc/apache2/mods-enabled/wsgi.load: Cannot load /usr/lib/apache2/modules /mod_wsgi.so into server: /usr/lib/apache2/modules/mod_wsgi.so: undefined symbol: PyCObject_FromVoidPtr Action 'configtest' failed. The Apache error log may have more information. ...fail! The error logs only inform us that it's a segfault: ` I checked to make sure that it's linked against the right python library with ldd mod_wsgi.so and got the output linux-gate.so.1 => (0x00d66000) libpython3.2mu.so.1.0 => /usr/lib/libpython3.2mu.so.1.0 (0x0065b000) libpthread.so.0 => /lib/i386-linux-gnu/libpthread.so.0 (0x00a20000) libc.so.6 => /lib/i386-linux-gnu/libc.so.6 (0x00110000) libssl.so.1.0.0 => /lib/i386-linux-gnu/libssl.so.1.0.0 (0x0028c000) libcrypto.so.1.0.0 => /lib/i386-linux-gnu/libcrypto.so.1.0.0 (0x0044c000) libffi.so.6 => /usr/lib/i386-linux-gnu/libffi.so.6 (0x002d9000) libz.so.1 => /lib/i386-linux-gnu/libz.so.1 (0x00eb3000) libexpat.so.1 => /lib/i386-linux-gnu/libexpat.so.1 (0x00abe000) libdl.so.2 => /lib/i386-linux-gnu/libdl.so.2 (0x002e0000) libutil.so.1 => /lib/i386-linux-gnu/libutil.so.1 (0x00c47000) libm.so.6 => /lib/i386-linux-gnu/libm.so.6 (0x00e24000) /lib/ld-linux.so.2 (0x0042c000) It seems to be linking against the python3 library so I'm not sure what the issue is. I have read on another question that mod-python can present problems however it was never installed. I saw that the directive WSGIPythonHome can be used to point to the correct python version and created a directory /usr/bin/apache2-python/ with a link named python and python3(the name I passed to the configure script) to /usr/bin/python3 This results in the same error. So I'm pretty sure it's using the correct version of python. I am now at a loss. Thanks in advance for any help. update Using the version from the repository I get the following log when I attempt to request a page: [Wed Mar 21 13:21:11 2012] [notice] child pid 5567 exit signal Aborted (6) Fatal Python error: Py_Initialize: Unable to get the locale encoding LookupError: no codec search functions registered: can't find encoding [Wed Mar 21 13:21:13 2012] [notice] child pid 5568 exit signal Aborted (6) Fatal Python error: Py_Initialize: Unable to get the locale encoding LookupError: no codec search functions registered: can't find encoding [Wed Mar 21 13:21:14 2012] [notice] caught SIGTERM, shutting down If I comment out the instruction to load mod-wsgi, the page serves normally.

  Read the article

• Set up lnux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project The above upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Create a chroot jail to hold sftp user via rssh. This will force SCP/SFTP and will circumvent traditional FTP server setup. #cd /tmp #wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm #rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm #useradd -m -d /home/dev -s /usr/bin/rssh dev #passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. #vi /etc/rssh.conf Uncomment line allowscp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). Above instructions for SFTP appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Application Does Not Start in Windows 7

  - by Jim Fell

  I recently installed a new 60GB SSD as my primary hard drive and re-installed Windows 7 Professional 64-bit. I then installed SSD Fresh from Abelssoft to optimize Windows to run on the SSD. It seemed to install okay, but when I try to run the utility, its splash screen appears briefly before it quietly closes. No errors are displayed; the utility just fails to launch. I have run SSD Fresh on another SSD-equipped Windows 7 Pro x64 computer in the past without any problems. Does anyone know what might be preventing the program from running? I tried running sfc /scannow from the command line (with administrator privileges), shutting down the Spybot Resident, and disabling the firewall and virus scanner. I also tried running the tool as administrator; I even tried reinstalling it, running the installer as administrator. No luck. Every time I try to launch the program the Event Viewer logs this same set of errors: Error 4/2/2012 11:35:44 PM Application Error 1000 (100) Faulting application name: SSDFresh.exe, version: 1.0.0.0, time stamp: 0x4f2a45d8 Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x000007ff0016dbba Faulting process id: 0x994 Faulting application start time: 0x01cd11fd9fe978df Faulting application path: C:\Program Files (x86)\SSD Fresh\SSDFresh.exe Faulting module path: unknown Report Id: dfeed551-7df0-11e1-a2c7-002522c47ec0 Error 4/2/2012 11:35:43 PM .NET Runtime 1026 None Application: SSDFresh.exe Framework Version: v4.0.30319 Description: The process was terminated due to an unhandled exception. Exception Info: System.NullReferenceException Stack: at AbBugReporter.BugForm.InitLanguage() at AbBugReporter.BugForm..ctor(AbFlexTrans.LanguageInfo, AbBugReporter.BugReportManager, Boolean) at AbBugReporter.BugReportManager.Show(System.Exception) at SSDFresh.App.App_DispatcherUnhandledException(System.Object, System.Windows.Threading.DispatcherUnhandledExceptionEventArgs) at System.Windows.Threading.Dispatcher.CatchException(System.Exception) at MS.Internal.Threading.ExceptionFilterHelper.TryCatchWhen(System.Object, System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.WrappedInvoke(System.Delegate, System.Object, Int32, System.Delegate) at System.Windows.Threading.Dispatcher.InvokeImpl(System.Windows.Threading.DispatcherPriority, System.TimeSpan, System.Delegate, System.Object, Int32) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr, Int32, IntPtr, IntPtr) at MS.Win32.UnsafeNativeMethods.DispatchMessage(System.Windows.Interop.MSG ByRef) at System.Windows.Threading.Dispatcher.PushFrameImpl(System.Windows.Threading.DispatcherFrame) at System.Windows.Application.RunInternal(System.Windows.Window) at System.Windows.Application.Run() at SSDFresh.App.Main() Error 4/2/2012 11:35:39 PM SideBySide 59 None Activation context generation failed for "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe".Error in manifest or policy file "C:\Windows\Microsoft.NET\Framework64\v4.0.30319\csc.exe.Config" on line 0. Invalid Xml syntax. Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None Error 4/2/2012 11:35:39 PM SideBySide 59 None For those who are interested, here is my system configuration: ASRock M3A770DE AM3 AMD 770 ATX AMD Motherboard AMD Athlon II X3 455 Rana 3.3GHz Socket AM3 95W Triple-Core Desktop Processor ADX455WFGMBOX G.SKILL Value Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) Desktop Memory Model F3-10600CL9D-8GBNT Mushkin Enhanced Chronos Deluxe MKNSSDCR60GB-DX 2.5" 60GB SATA III Synchronous MLC Internal Solid State Drive (SSD) (Primary/Boot HD) Western Digital Caviar Blue RFHWD1600AAJS 160GB 7200 RPM SATA 3.0Gb/s 3.5" Internal Hard Drive -Bare Drive (Secondary HD) Sony Optiarc CD/DVD Burner Black SATA Model AD-7261S-0B LightScribe Support RAIDMAX RX-850AE 850W ATX12V v2.3 / EPS12V SLI Certified CrossFire Ready 80 PLUS GOLD Certified Modular Active PFC Power Supply ASUS HD7850-DC2-2GD5 Radeon HD 7850 2GB 256-bit GDDR5 PCI Express 3.0 x16 HDCP Ready CrossFireX Support Video Card Asus ML228H 21.5" Full HD LED BackLight LED Monitor Slim Design (x3)

  Read the article

• Unable to remove limit on memory usage for PHP script.

  - by Jess Telford

  The Situation I am having an issue with a PHP script getting the following error message: Fatal error: Out of memory (allocated 359923712) (tried to allocate 72 bytes) in /path/to/piwik/core/DataTable.php on line 969 The script I'm running is: /path/to/piwik/misc/cron/archive.sh I am assuming the numbers are Bytes, which means that total is approximately 360MB. For all intents and purposes, I have increased the memory limits on the server well above 360MB, yet this is the number (give or take a byte) it consistently errors out at. Please note: This question is not about fixing a memory leak in the script, nor about why the script itself is using so much memory. The script is part of the Piwik archiving process, so I cannot just fix any memory leaks, etc. For more info on this script and why I am increasing the memory limit, see "How to setup auto archiving" The question Given that the script is attempting to use over 360MB of memory, which I cannot change, why does it not seem possible for me to increase the amount of memory available to php on my server? What I've tried Increasing PHP's memory_limit Given the php.ini file: php -i | grep php.ini Configuration File (php.ini) Path => /usr/local/lib Loaded Configuration File => /usr/local/lib/php.ini I have edited that file, so the memory_limit directive reads; memory_limit = -1 Restart Apache, and check the new value has stuck; $ php -i | grep memory_limit memory_limit => -1 => -1 Run the script, and get the same error. I've also tried 1G, 768M, etc, all to the same result (ie; no change). Update 22nd June: Based on Vangel's help, I have attempted to set post_max_size to 20M in combination with setting memory_limit. Again, this has no effect. Removing the memory limit on child processes of Apache I have found and edited the httpd.conf file to make sure there is no RLimitMEM directive. I then used WHM's Apache Configuration Memory Usage Restrictions to generate a restriction, which it claimed was at 1000M (and confirmed by checking httpd.conf). Both of these resulted in no change to the script erroring at 360MB. Increasing the per process memory limits of Linux The current limits set on the system: $ ulimit -m 524288 $ ulimit -v 524288 I have attempted to set both of these to unlimited: $ ulimit -m unlimited $ ulimit -v unlimited $ ulimit -m unlimited $ ulimit -v unlimited Once again, this has resulted in absolutely no improvement in my problem. My setup $ cat /etc/redhat-release CentOS release 5.5 (Final) $ uname -a Linux example.com 2.6.18-164.15.1.el5 #1 SMP Wed Mar 17 11:30:06 EDT 2010 x86_64 x86_64 x86_64 GNU/Linux $ php -i | grep "PHP Version" PHP Version => 5.2.9 $ httpd -V Server version: Apache/2.0.63 Server built: Feb 2 2011 01:25:12 Cpanel::Easy::Apache v3.2.0 rev5291 Server's Module Magic Number: 20020903:13 Server loaded: APR 0.9.17, APR-UTIL 0.9.15 Compiled using: APR 0.9.17, APR-UTIL 0.9.15 Architecture: 64-bit Server compiled with.... -D APACHE_MPM_DIR="server/mpm/prefork" -D APR_HAS_SENDFILE -D APR_HAS_MMAP -D APR_HAVE_IPV6 (IPv4-mapped addresses enabled) -D APR_USE_SYSVSEM_SERIALIZE -D APR_USE_PTHREAD_SERIALIZE -D SINGLE_LISTEN_UNSERIALIZED_ACCEPT -D APR_HAS_OTHER_CHILD -D AP_HAVE_RELIABLE_PIPED_LOGS -D HTTPD_ROOT="/usr/local/apache" -D SUEXEC_BIN="/usr/local/apache/bin/suexec" -D DEFAULT_PIDLOG="logs/httpd.pid" -D DEFAULT_SCOREBOARD="logs/apache_runtime_status" -D DEFAULT_LOCKFILE="logs/accept.lock" -D DEFAULT_ERRORLOG="logs/error_log" -D AP_TYPES_CONFIG_FILE="conf/mime.types" -D SERVER_CONFIG_FILE="conf/httpd.conf" Output of $ php -i: http://pastebin.com/EiRut6Nm

  Read the article

• Windows Service SearchIndexer.exe Crashes on Indexing

  - by Josh Jay

  Relevant Specs: Windows 7 Professional 64-bit SP1 Outlook 2010 Version 14.0.7116.5000 (32-bit) Original Symptom: In outlook, I attempted to search for an email but nothing ever returned and the indicator kept going like it was searching. Attempted Resolutions: I investigated the search options and with some research noticed the Windows Service "Windows Search" (SearchIndexer.exe) was not running. I attempted to start it but I receive this error message: "Windows could not start the Windows Search service on Local Computer. Error 1067: The process terminated unexpectedly." The Event Viewer gives this error entry: Log Name: Application Source: Application Error Date: 6/3/2014 11:02:05 AM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ***REMOVED FOR POST*** Description: Faulting application name: SearchIndexer.exe, version: 7.0.7601.17610, time stamp: 0x4dc0d019 Faulting module name: KERNELBASE.dll, version: 6.1.7601.18229, time stamp: 0x51fb1677 Exception code: 0xc0000005 Fault offset: 0x000000000000940d Faulting process id: 0x6a0 Faulting application start time: 0x01cf7f3cc83757c6 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\system32\KERNELBASE.dll Report Id: 06424160-eb30-11e3-9555-843a4b07b336 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2014-06-03T15:02:05.000000000Z" /> <EventRecordID>602923</EventRecordID> <Channel>Application</Channel> <Computer>M6700-12011.ncaa.org</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7601.17610</Data> <Data>4dc0d019</Data> <Data>KERNELBASE.dll</Data> <Data>6.1.7601.18229</Data> <Data>51fb1677</Data> <Data>c0000005</Data> <Data>000000000000940d</Data> <Data>6a0</Data> <Data>01cf7f3cc83757c6</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\system32\KERNELBASE.dll</Data> <Data>06424160-eb30-11e3-9555-843a4b07b336</Data> </EventData> </Event> The regular windows search (from start menu) works fine, and if I reboot the machine the service starts up OK but as soon as it kicks off when I let the machine idle for long enough it crashes (same Event Viewer entry). We also tried the Microsoft Utility to no avail. Has anyone seen this issue before?

  Read the article

• How do I reset/update my BIOS for Optiplex GX280?

  - by Sam Langlhey

  So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

  Read the article

• Outlook Web Access, reverse proxy and browser

  - by M'vy

  Hi SF'ers! We recently moved an exchange server behind a reverse proxy due to the loss of a public IP. I've managed to configure the reverse proxy (httpd proxy_http). But there is a problem for the SSL configuration. When accessing the OWA interface with Firefox, all is ok and working. When accessing with MSIE or Chrome, they do not retrieve the good SSL Certificate. I think this is due to the multiples virtual host for httpd. Is there a workaround to make sure MSIE/Chrome request the certificate for the good domain name like FF does? Already tested with the SSL virtual host : SetEnvIf User-Agent ".*MSIE.*" value BrowserMSIE Header unset WWW-Authenticate Header add WWW-Authenticate "Basic realm=exchange.domain.com" A: ProxyPreserveHost On also: BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 Or: SetEnvIf User-Agent ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 And lots of ProxyPassand ProxyReversePath on /exchweb /exchange /public etc... And it still don't seem to work. Any clue? Thanks. Edit 1: Precision of versions # openssl version OpenSSL 0.9.8k-fips 25 Mar 2009 /usr/sbin/httpd -v Server version: Apache/2.2.11 (Unix) Server built: Mar 17 2009 09:15:10 Browser versions : MSIE : 8.0.6001 Opera: Version 11.01 Revision 1190 Firefox: 3.6.15 Chrome: 10.0.648.151 Operating System: Windows Vista 32bits. They are all SNI compliant, I've tested them this afternoon https://sni.velox.ch/ You're right Shane Madden, I have multiple sites on the same public IP (and same port as well). The server itself is just a reverse proxy, that rewrite addresses to internal servers. The default host is a dev site, configure with the certificate that does not match the OWA (of course... would have been to easy) <VirtualHost *:443> ServerName dev2.domain.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/error-%y%m%d.log 86400" LogLevel warn RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes SSLEngine on SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/domain.com.crt SSLCertificateKeyFile /etc/httpd/ssl/domain.com.key RewriteCond %{HTTP_HOST} dev2\.domain\.com RewriteRule ^/(.*)$ http://dev2.domain.com/$1 [L,P] </VirtualHost> The certificate of domain is a *.domain.com The second vHost is : <VirtualHost *:443> ServerName exchange.domain2.com ServerAdmin [email protected] CustomLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/access-%y%m%d.log 86400" combined ErrorLog "| /usr/sbin/rotatelogs /var/log/httpd/exchange/error-%y%m%d.log 86400" LogLevel warn SSLEngine on SSLProxyEngine On SSLProtocol -all +SSLv3 +TLSv1 SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL:+SSLv3 SSLCertificateFile /etc/httpd/ssl/exchange.pem SSLCertificateKeyFile /etc/httpd/ssl/exchange.key RewriteEngine on SetEnvIfNoCase X-Forwarded-For .+ proxy=yes RewriteCond %{HTTP_HOST} exchange\.domain2\.com RewriteRule ^/(.*)$ https://exchange.domain2.com/$1 [L,P] </VirtualHost> and it's certificate is exchange.domain2.com only. I presume the SNI is somewhere not activated on my server. The versions of openssl and apache seams to be ok for the SNI support. The only thing I do not know is if httpd has been compile with the good options. (I assume it's a fedora packet).

  Read the article

• Email from my new vps is marked as spam

  - by Chriswede

  I got a new vps from x10vps (x10hosting) and set up the domain via cloudflare. This is what the email looks like: Delivered-To: [email protected] Received: by 10.64.19.240 with SMTP id i16csp357708iee; Tue, 9 Oct 2012 01:29:48 -0700 (PDT) Received: by 10.50.57.130 with SMTP id i2mr908846igq.56.1349771387599; Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id v8si25630942ica.46.2012.10.09.01.29.46 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected] Received: from nk11p03mm-asmtp010.mac.com ([17.158.232.169]:54276) by power.SOURCEAPE.COM with esmtp (Exim 4.80) (envelope-from <[email protected]>) id 1TLVBD-0004Ig-1Y for [email protected]; Tue, 09 Oct 2012 12:28:43 +0400 I then tried to enable SPF and DKIM and got following massage In order to ensure that SPF or DKIM takes effect, you must confirm that this server is an authoritative nameserver for chvw.de. If you need help, contact your hosting provider. Status: Enabled Warning: cPanel is unable to verify that this server is an authoritative nameserver for chvw.de. [?] and the email header now looks like this: Delivered-To: [email protected] Received: by 10.50.183.227 with SMTP id ep3csp14506igc; Tue, 9 Oct 2012 01:55:23 -0700 (PDT) Received: by 10.50.40.133 with SMTP id x5mr992934igk.32.1349772923717; Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id ng8si25688859icb.42.2012.10.09.01.55.23 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected]; dkim=neutral (bad format) [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=chvw.de; s=default; h=Message-ID:Subject:To:From:Date:Content-Transfer-Encoding:Content-Type:MIME-Version; bh=iugsx3Lx0KnqjR7dj3wyQHnJ9pe/z3ntYEVk80k8rx4=; b=IrYsCtHdoPubXVOvLqxd7sLE/TyQTS5P3OrEg5SSUSKnQQcQ/fWWyBrmsrgkFSsw6jCmmRWMDR09vH5bQRpFPMA57B7pf8QRKhwXOWFBV+GnVUqICsfRjnNPvhx/lNp5; Received: from localhost ([127.0.0.1]:46539 helo=direct.chvw.de) by power.SOURCEAPE.COM with esmtpa (Exim 4.80) (envelope-from <[email protected]>) id 1TLVb0-0004dZ-Kd for [email protected]; Tue, 09 Oct 2012 12:55:22 +0400

  Read the article

• JBoss https on port other than 8080 not working

  - by MilindaD

  We have a server with two JBoss instances where one runs on 8080, the other on 8081. We need to have HTTPS enabled for the 8081 server, firstly we tried enabling https on the 8080 port instance by generating the keystore and editing the server.xml and it successfully worked. However when we tried the same thing for 8081 it did not, note that we removed https for the 8080 server first before enabling it for 8081. This is what was used for both server.xml for 8080 and 8081. The only difference was that the port was changed from 8080 to 8081 when trying to enable https for 8081 port instance. What am I doing wrong and what needs to be changed? NOTE : When I meant enabled for 8080 I meant when you visit https:// URL:8484 you will actually be visiting the 8080 port instance. However when ssl is enabled for 8081 and I visit https:// URL:8484 I get that the web page is unavailable. COMMENTLESS VERSION <Server> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <Listener className="org.apache.catalina.core.JasperListener" /> <Service name="jboss.web"> <!-- https --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- https1 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server> WITH COMMENTS VERSION <Server> <!--APR library loader. Documentation at /docs/apr.html --> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener" /> <!-- Use a custom version of StandardService that allows the connectors to be started independent of the normal lifecycle start to allow web apps to be deployed before starting the connectors. --> <Service name="jboss.web"> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" address="${jboss.bind.address}" maxThreads="350" maxHttpHeaderSize="8192" emptySessionPath="true" protocol="HTTP/1.1" enableLookups="false" redirectPort="8443" acceptCount="100" connectionTimeout="20000" disableUploadTimeout="true" compression="on" ompressableMimeType="text/html,text/css,text/javascript,application/json,text/xml,text/plain,application/x-javascript,application/javascript"/> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" keystoreFile="${jboss.server.home.dir}/conf/zara.keystore" keystorePass="zara2010" clientAuth="false" sslProtocol="TLS" compression="on" /> --> <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" address="${jboss.bind.address}" keystoreFile="${jboss.server.home.dir}/conf/supun1.keystore" keystorePass="aaaaaa" truststoreFile="${jboss.server.home.dir}/conf/supun1.keystore" truststorePass="aaaaaa" /> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" address="${jboss.bind.address}" protocol="AJP/1.3" emptySessionPath="true" enableLookups="false" redirectPort="8443" /> <Engine name="jboss.web" defaultHost="localhost" jvmRoute="khms1"> <!-- The JAAS based authentication and authorization realm implementation that is compatible with the jboss 3.2.x realm implementation. - certificatePrincipal : the class name of the org.jboss.security.auth.certs.CertificatePrincipal impl used for mapping X509[] cert chains to a Princpal. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles --> <Realm className="org.jboss.web.tomcat.security.JBossSecurityMgrRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> <!-- A subclass of JBossSecurityMgrRealm that uses the authentication behavior of JBossSecurityMgrRealm, but overrides the authorization checks to use JACC permissions with the current java.security.Policy to determine authorized access. - allRolesMode : how to handle an auth-constraint with a role-name=*, one of strict, authOnly, strictAuthOnly + strict = Use the strict servlet spec interpretation which requires that the user have one of the web-app/security-role/role-name + authOnly = Allow any authenticated user + strictAuthOnly = Allow any authenticated user only if there are no web-app/security-roles <Realm className="org.jboss.web.tomcat.security.JaccAuthorizationRealm" certificatePrincipal="org.jboss.security.auth.certs.SubjectDNMapping" allRolesMode="authOnly" /> --> <Host name="localhost" autoDeploy="false" deployOnStartup="false" deployXML="false" configClass="org.jboss.web.tomcat.security.config.JBossContextConfig" > <!-- Uncomment to enable request dumper. This Valve "logs interesting contents from the specified Request (before processing) and the corresponding Response (after processing). It is especially useful in debugging problems related to headers and cookies." --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve" /> --> <!-- Access logger --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" prefix="localhost_access_log." suffix=".log" pattern="common" directory="${jboss.server.log.dir}" resolveHosts="false" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host. Does not provide SSO across a cluster. If this valve is used, do not use the JBoss ClusteredSingleSignOn valve shown below. A new configuration attribute is available beginning with release 4.0.4: cookieDomain configures the domain to which the SSO cookie will be scoped (i.e. the set of hosts to which the cookie will be presented). By default the cookie is scoped to "/", meaning the host that presented it. Set cookieDomain to a wider domain (e.g. "xyz.com") to allow an SSO to span more than one hostname. --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Uncomment to enable single sign-on across web apps deployed to this host AND to all other hosts in the cluster. If this valve is used, do not use the standard Tomcat SingleSignOn valve shown above. Valve uses a JBossCache instance to support SSO credential caching and replication across the cluster. The JBossCache instance must be configured separately. By default, the valve shares a JBossCache with the service that supports HttpSession replication. See the "jboss-web-cluster-service.xml" file in the server/all/deploy directory for cache configuration details. Besides the attributes supported by the standard Tomcat SingleSignOn valve (see the Tomcat docs), this version also supports the following attributes: cookieDomain see above treeCacheName JMX ObjectName of the JBossCache MBean used to support credential caching and replication across the cluster. If not set, the default value is "jboss.cache:service=TomcatClusteringCache", the standard ObjectName of the JBossCache MBean used to support session replication. --> <Valve className="org.jboss.web.tomcat.service.sso.ClusteredSingleSignOn" /> <!-- Check for unclosed connections and transaction terminated checks in servlets/jsps. Important: The dependency on the CachedConnectionManager in META-INF/jboss-service.xml must be uncommented, too --> <Valve className="org.jboss.web.tomcat.service.jca.CachedConnectionValve" cachedConnectionManagerObjectName="jboss.jca:service=CachedConnectionManager" transactionManagerObjectName="jboss:service=TransactionManager" /> </Host> </Engine> </Service> </Server>

  Read the article

• Set up lnux box for hosting a-z [apache mysql php ssl]

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP: To upgrade PHP to the latest version, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! cd /tmp #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm #rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm #wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm #rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. [will list all packages available in the IUS repo] rpm -qa | grep php [will list installed packages needed to be removed. the installed packages need to be removed before you can install the IUS packages otherwise there will be conflicts] #yum shell >remove php-gd php-cli php-odbc php-mbstring php-pdo php php-xml php-common php-ldap php-mysql php-imap Setting up Remove Process >install php53 php53-mcrypt php53-mysql php53-cli php53-common php53-ldap php53-imap php53-devel >transaction solve >transaction run Leaving Shell #php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) This process removes the old version of PHP and installs the latest. To upgrade mysql: Pretty much the same process as above with PHP #/etc/init.d/mysqld stop [OK] rpm -qa | grep mysql [installed mysql packages] #yum shell >remove mysql mysql-server Setting up Remove Process >install mysql51 mysql51-server mysql51-devel >transaction solve >transaction run Leaving Shell #service mysqld start [OK] #mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure Virtualhosts for SSL, setting up a CA, setting up SFTP with openSSH, or anything else would be appreciated.

  Read the article

• Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

  - by Jørgen

  I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

  Read the article

• Product Review: qlWebDS Pro

  There are many products available for creating directory style web sites, but web masters prefer simple ones that contain features relevant to them. In this review, Anand puts the Pro version of qlWebDS software to the test. He examines the various features and provides suggestions for improving the quality of the product.

  Read the article

• Loading latest firmware iwlwifi-6000

  - by grzeh

  I just installed 11.10 on Dell XPS 15z. Somebody know why kernel does not load the latest firmware for wifi Intel Centrino Advanced-N 6230. $ modinfo iwlagn |grep iwlwifi-6000 firmware: iwlwifi-6000g2b-5.ucode firmware: iwlwifi-6000g2a-5.ucode firmware: iwlwifi-6000-4.ucode In package linux-firmware there is latest version (iwlwifi-6000g2b-6.ucode) $ dpkg -L linux-firmware | grep iwlwifi-6000 /lib/firmware/iwlwifi-6000-4.ucode /lib/firmware/iwlwifi-6000g2a-5.ucode /lib/firmware/iwlwifi-6000g2b-5.ucode **/lib/firmware/iwlwifi-6000g2b-6.ucode**

  Read the article

• .NET Reflector 6, .NET Reflector Pro, TestDriven.NET, .NET 4.0 and Mono

  - by Bart Read

  By now you may well have noticed that .NET Reflector 6 and .NET Reflector Pro are out in the wild. The official launch happened today, although we actually put the software out last Thursday as part of a phased release plan to ensure that everything went smoothly today which, so far, it seems to have done. Clive and Alex have already talked extensively about what the new version and the Pro extension do, so I'm not going to go into any detail here, but I've linked to their blogs at the bottom. What...(read more)

  Read the article

• Using FiddlerCore to capture HTTP Requests with .NET

  - by Rick Strahl

  Over the last few weeks I’ve been working on my Web load testing utility West Wind WebSurge. One of the key components of a load testing tool is the ability to capture URLs effectively so that you can play them back later under load. One of the options in WebSurge for capturing URLs is to use its built-in capture tool which acts as an HTTP proxy to capture any HTTP and HTTPS traffic from most Windows HTTP clients, including Web Browsers as well as standalone Windows applications and services. To make this happen, I used Eric Lawrence’s awesome FiddlerCore library, which provides most of the functionality of his desktop Fiddler application, all rolled into an easy to use library that you can plug into your own applications. FiddlerCore makes it almost too easy to capture HTTP content! For WebSurge I needed to capture all HTTP traffic in order to capture the full HTTP request – URL, headers and any content posted by the client. The result of what I ended up creating is this semi-generic capture form: In this post I’m going to demonstrate how easy it is to use FiddlerCore to build this HTTP Capture Form.  If you want to jump right in here are the links to get Telerik’s Fiddler Core and the code for the demo provided here. FiddlerCore Download FiddlerCore on NuGet Show me the Code (WebSurge Integration code from GitHub) Download the WinForms Sample Form West Wind Web Surge (example implementation in live app) Note that FiddlerCore is bound by a license for commercial usage – see license.txt in the FiddlerCore distribution for details. Integrating FiddlerCore FiddlerCore is a library that simply plugs into your application. You can download it from the Telerik site and manually add the assemblies to your project, or you can simply install the NuGet package via:       PM> Install-Package FiddlerCore The library consists of the FiddlerCore.dll as well as a couple of support libraries (CertMaker.dll and BCMakeCert.dll) that are used for installing SSL certificates. I’ll have more on SSL captures and certificate installation later in this post. But first let’s see how easy it is to use FiddlerCore to capture HTTP content by looking at how to build the above capture form. Capturing HTTP Content Once the library is installed it’s super easy to hook up Fiddler functionality. Fiddler includes a number of static class methods on the FiddlerApplication object that can be called to hook up callback events as well as actual start monitoring HTTP URLs. In the following code directly lifted from WebSurge, I configure a few filter options on Form level object, from the user inputs shown on the form by assigning it to a capture options object. In the live application these settings are persisted configuration values, but in the demo they are one time values initialized and set on the form. Once these options are set, I hook up the AfterSessionComplete event to capture every URL that passes through the proxy after the request is completed and start up the Proxy service:void Start() { if (tbIgnoreResources.Checked) CaptureConfiguration.IgnoreResources = true; else CaptureConfiguration.IgnoreResources = false; string strProcId = txtProcessId.Text; if (strProcId.Contains('-')) strProcId = strProcId.Substring(strProcId.IndexOf('-') + 1).Trim(); strProcId = strProcId.Trim(); int procId = 0; if (!string.IsNullOrEmpty(strProcId)) { if (!int.TryParse(strProcId, out procId)) procId = 0; } CaptureConfiguration.ProcessId = procId; CaptureConfiguration.CaptureDomain = txtCaptureDomain.Text; FiddlerApplication.AfterSessionComplete += FiddlerApplication_AfterSessionComplete; FiddlerApplication.Startup(8888, true, true, true); } The key lines for FiddlerCore are just the last two lines of code that include the event hookup code as well as the Startup() method call. Here I only hook up to the AfterSessionComplete event but there are a number of other events that hook various stages of the HTTP request cycle you can also hook into. Other events include BeforeRequest, BeforeResponse, RequestHeadersAvailable, ResponseHeadersAvailable and so on. In my case I want to capture the request data and I actually have several options to capture this data. AfterSessionComplete is the last event that fires in the request sequence and it’s the most common choice to capture all request and response data. I could have used several other events, but AfterSessionComplete is one place where you can look both at the request and response data, so this will be the most common place to hook into if you’re capturing content. The implementation of AfterSessionComplete is responsible for capturing all HTTP request headers and it looks something like this:private void FiddlerApplication_AfterSessionComplete(Session sess) { // Ignore HTTPS connect requests if (sess.RequestMethod == "CONNECT") return; if (CaptureConfiguration.ProcessId > 0) { if (sess.LocalProcessID != 0 && sess.LocalProcessID != CaptureConfiguration.ProcessId) return; } if (!string.IsNullOrEmpty(CaptureConfiguration.CaptureDomain)) { if (sess.hostname.ToLower() != CaptureConfiguration.CaptureDomain.Trim().ToLower()) return; } if (CaptureConfiguration.IgnoreResources) { string url = sess.fullUrl.ToLower(); var extensions = CaptureConfiguration.ExtensionFilterExclusions; foreach (var ext in extensions) { if (url.Contains(ext)) return; } var filters = CaptureConfiguration.UrlFilterExclusions; foreach (var urlFilter in filters) { if (url.Contains(urlFilter)) return; } } if (sess == null || sess.oRequest == null || sess.oRequest.headers == null) return; string headers = sess.oRequest.headers.ToString(); var reqBody = sess.GetRequestBodyAsString(); // if you wanted to capture the response //string respHeaders = session.oResponse.headers.ToString(); //var respBody = session.GetResponseBodyAsString(); // replace the HTTP line to inject full URL string firstLine = sess.RequestMethod + " " + sess.fullUrl + " " + sess.oRequest.headers.HTTPVersion; int at = headers.IndexOf("\r\n"); if (at < 0) return; headers = firstLine + "\r\n" + headers.Substring(at + 1); string output = headers + "\r\n" + (!string.IsNullOrEmpty(reqBody) ? reqBody + "\r\n" : string.Empty) + Separator + "\r\n\r\n"; BeginInvoke(new Action<string>((text) => { txtCapture.AppendText(text); UpdateButtonStatus(); }), output); } The code starts by filtering out some requests based on the CaptureOptions I set before the capture is started. These options/filters are applied when requests actually come in. This is very useful to help narrow down the requests that are captured for playback based on options the user picked. I find it useful to limit requests to a certain domain for captures, as well as filtering out some request types like static resources – images, css, scripts etc. This is of course optional, but I think it’s a common scenario and WebSurge makes good use of this feature. AfterSessionComplete like other FiddlerCore events, provides a Session object parameter which contains all the request and response details. There are oRequest and oResponse objects to hold their respective data. In my case I’m interested in the raw request headers and body only, as you can see in the commented code you can also retrieve the response headers and body. Here the code captures the request headers and body and simply appends the output to the textbox on the screen. Note that the Fiddler events are asynchronous, so in order to display the content in the UI they have to be marshaled back the UI thread with BeginInvoke, which here simply takes the generated headers and appends it to the existing textbox test on the form. As each request is processed, the headers are captured and appended to the bottom of the textbox resulting in a Session HTTP capture in the format that Web Surge internally supports, which is basically raw request headers with a customized 1st HTTP Header line that includes the full URL rather than a server relative URL. When the capture is done the user can either copy the raw HTTP session to the clipboard, or directly save it to file. This raw capture format is the same format WebSurge and also Fiddler use to import/export request data. While this code is application specific, it demonstrates the kind of logic that you can easily apply to the request capture process, which is one of the reasonsof why FiddlerCore is so powerful. You get to choose what content you want to look up as part of your own application logic and you can then decide how to capture or use that data as part of your application. The actual captured data in this case is only a string. The user can edit the data by hand or in the the case of WebSurge, save it to disk and automatically open the captured session as a new load test. Stopping the FiddlerCore Proxy Finally to stop capturing requests you simply disconnect the event handler and call the FiddlerApplication.ShutDown() method:void Stop() { FiddlerApplication.AfterSessionComplete -= FiddlerApplication_AfterSessionComplete; if (FiddlerApplication.IsStarted()) FiddlerApplication.Shutdown(); } As you can see, adding HTTP capture functionality to an application is very straight forward. FiddlerCore offers tons of features I’m not even touching on here – I suspect basic captures are the most common scenario, but a lot of different things can be done with FiddlerCore’s simple API interface. Sky’s the limit! The source code for this sample capture form (WinForms) is provided as part of this article. Adding Fiddler Certificates with FiddlerCore One of the sticking points in West Wind WebSurge has been that if you wanted to capture HTTPS/SSL traffic, you needed to have the full version of Fiddler and have HTTPS decryption enabled. Essentially you had to use Fiddler to configure HTTPS decryption and the associated installation of the Fiddler local client certificate that is used for local decryption of incoming SSL traffic. While this works just fine, requiring to have Fiddler installed and then using a separate application to configure the SSL functionality isn’t ideal. Fortunately FiddlerCore actually includes the tools to register the Fiddler Certificate directly using FiddlerCore. Why does Fiddler need a Certificate in the first Place? Fiddler and FiddlerCore are essentially HTTP proxies which means they inject themselves into the HTTP conversation by re-routing HTTP traffic to a special HTTP port (8888 by default for Fiddler) and then forward the HTTP data to the original client. Fiddler injects itself as the system proxy in using the WinInet Windows settings  which are the same settings that Internet Explorer uses and that are configured in the Windows and Internet Explorer Internet Settings dialog. Most HTTP clients running on Windows pick up and apply these system level Proxy settings before establishing new HTTP connections and that’s why most clients automatically work once Fiddler – or FiddlerCore/WebSurge are running. For plain HTTP requests this just works – Fiddler intercepts the HTTP requests on the proxy port and then forwards them to the original port (80 for HTTP and 443 for SSL typically but it could be any port). For SSL however, this is not quite as simple – Fiddler can easily act as an HTTPS/SSL client to capture inbound requests from the server, but when it forwards the request to the client it has to also act as an SSL server and provide a certificate that the client trusts. This won’t be the original certificate from the remote site, but rather a custom local certificate that effectively simulates an SSL connection between the proxy and the client. If there is no custom certificate configured for Fiddler the SSL request fails with a certificate validation error. The key for this to work is that a custom certificate has to be installed that the HTTPS client trusts on the local machine. For a much more detailed description of the process you can check out Eric Lawrence’s blog post on Certificates. If you’re using the desktop version of Fiddler you can install a local certificate into the Windows certificate store. Fiddler proper does this from the Options menu: This operation does several things: It installs the Fiddler Root Certificate It sets trust to this Root Certificate A new client certificate is generated for each HTTPS site monitored Certificate Installation with FiddlerCore You can also provide this same functionality using FiddlerCore which includes a CertMaker class. Using CertMaker is straight forward to use and it provides an easy way to create some simple helpers that can install and uninstall a Fiddler Root certificate:public static bool InstallCertificate() { if (!CertMaker.rootCertExists()) { if (!CertMaker.createRootCert()) return false; if (!CertMaker.trustRootCert()) return false; } return true; } public static bool UninstallCertificate() { if (CertMaker.rootCertExists()) { if (!CertMaker.removeFiddlerGeneratedCerts(true)) return false; } return true; } InstallCertificate() works by first checking whether the root certificate is already installed and if it isn’t goes ahead and creates a new one. The process of creating the certificate is a two step process – first the actual certificate is created and then it’s moved into the certificate store to become trusted. I’m not sure why you’d ever split these operations up since a cert created without trust isn’t going to be of much value, but there are two distinct steps. When you trigger the trustRootCert() method, a message box will pop up on the desktop that lets you know that you’re about to trust a local private certificate. This is a security feature to ensure that you really want to trust the Fiddler root since you are essentially installing a man in the middle certificate. It’s quite safe to use this generated root certificate, because it’s been specifically generated for your machine and thus is not usable from external sources, the only way to use this certificate in a trusted way is from the local machine. IOW, unless somebody has physical access to your machine, there’s no useful way to hijack this certificate and use it for nefarious purposes (see Eric’s post for more details). Once the Root certificate has been installed, FiddlerCore/Fiddler create new certificates for each site that is connected to with HTTPS. You can end up with quite a few temporary certificates in your certificate store. To uninstall you can either use Fiddler and simply uncheck the Decrypt HTTPS traffic option followed by the remove Fiddler certificates button, or you can use FiddlerCore’s CertMaker.removeFiddlerGeneratedCerts() which removes the root cert and any of the intermediary certificates Fiddler created. Keep in mind that when you uninstall you uninstall the certificate for both FiddlerCore and Fiddler, so use UninstallCertificate() with care and realize that you might affect the Fiddler application’s operation by doing so as well. When to check for an installed Certificate Note that the check to see if the root certificate exists is pretty fast, while the actual process of installing the certificate is a relatively slow operation that even on a fast machine takes a few seconds. Further the trust operation pops up a message box so you probably don’t want to install the certificate repeatedly. Since the check for the root certificate is fast, you can easily put a call to InstallCertificate() in any capture startup code – in which case the certificate installation only triggers when a certificate is in fact not installed. Personally I like to make certificate installation explicit – just like Fiddler does, so in WebSurge I use a small drop down option on the menu to install or uninstall the SSL certificate:   This code calls the InstallCertificate and UnInstallCertificate functions respectively – the experience with this is similar to what you get in Fiddler with the extra dialog box popping up to prompt confirmation for installation of the root certificate. Once the cert is installed you can then capture SSL requests. There’s a gotcha however… Gotcha: FiddlerCore Certificates don’t stick by Default When I originally tried to use the Fiddler certificate installation I ran into an odd problem. I was able to install the certificate and immediately after installation was able to capture HTTPS requests. Then I would exit the application and come back in and try the same HTTPS capture again and it would fail due to a missing certificate. CertMaker.rootCertExists() would return false after every restart and if re-installed the certificate a new certificate would get added to the certificate store resulting in a bunch of duplicated root certificates with different keys. What the heck? CertMaker and BcMakeCert create non-sticky CertificatesI turns out that FiddlerCore by default uses different components from what the full version of Fiddler uses. Fiddler uses a Windows utility called MakeCert.exe to create the Fiddler Root certificate. FiddlerCore however installs the CertMaker.dll and BCMakeCert.dll assemblies, which use a different crypto library (Bouncy Castle) for certificate creation than MakeCert.exe which uses the Windows Crypto API. The assemblies provide support for non-windows operation for Fiddler under Mono, as well as support for some non-Windows certificate platforms like iOS and Android for decryption. The bottom line is that the FiddlerCore provided bouncy castle assemblies are not sticky by default as the certificates created with them are not cached as they are in Fiddler proper. To get certificates to ‘stick’ you have to explicitly cache the certificates in Fiddler’s internal preferences. A cache aware version of InstallCertificate looks something like this:public static bool InstallCertificate() { if (!CertMaker.rootCertExists()) { if (!CertMaker.createRootCert()) return false; if (!CertMaker.trustRootCert()) return false; App.Configuration.UrlCapture.Cert = FiddlerApplication.Prefs.GetStringPref("fiddler.certmaker.bc.cert", null); App.Configuration.UrlCapture.Key = FiddlerApplication.Prefs.GetStringPref("fiddler.certmaker.bc.key", null); } return true; } public static bool UninstallCertificate() { if (CertMaker.rootCertExists()) { if (!CertMaker.removeFiddlerGeneratedCerts(true)) return false; } App.Configuration.UrlCapture.Cert = null; App.Configuration.UrlCapture.Key = null; return true; } In this code I store the Fiddler cert and private key in an application configuration settings that’s stored with the application settings (App.Configuration.UrlCapture object). These settings automatically persist when WebSurge is shut down. The values are read out of Fiddler’s internal preferences store which is set after a new certificate has been created. Likewise I clear out the configuration settings when the certificate is uninstalled. In order for these setting to be used you have to also load the configuration settings into the Fiddler preferences *before* a call to rootCertExists() is made. I do this in the capture form’s constructor:public FiddlerCapture(StressTestForm form) { InitializeComponent(); CaptureConfiguration = App.Configuration.UrlCapture; MainForm = form; if (!string.IsNullOrEmpty(App.Configuration.UrlCapture.Cert)) { FiddlerApplication.Prefs.SetStringPref("fiddler.certmaker.bc.key", App.Configuration.UrlCapture.Key); FiddlerApplication.Prefs.SetStringPref("fiddler.certmaker.bc.cert", App.Configuration.UrlCapture.Cert); }} This is kind of a drag to do and not documented anywhere that I could find, so hopefully this will save you some grief if you want to work with the stock certificate logic that installs with FiddlerCore. MakeCert provides sticky Certificates and the same functionality as Fiddler But there’s actually an easier way. If you want to skip the above Fiddler preference configuration code in your application you can choose to distribute MakeCert.exe instead of certmaker.dll and bcmakecert.dll. When you use MakeCert.exe, the certificates settings are stored in Windows so they are available without any custom configuration inside of your application. It’s easier to integrate and as long as you run on Windows and you don’t need to support iOS or Android devices is simply easier to deal with. To integrate into your project, you can remove the reference to CertMaker.dll (and the BcMakeCert.dll assembly) from your project. Instead copy MakeCert.exe into your output folder. To make sure MakeCert.exe gets pushed out, include MakeCert.exe in your project and set the Build Action to None, and Copy to Output Directory to Copy if newer. Note that the CertMaker.dll reference in the project has been removed and on disk the files for Certmaker.dll, as well as the BCMakeCert.dll files on disk. Keep in mind that these DLLs are resources of the FiddlerCore NuGet package, so updating the package may end up pushing those files back into your project. Once MakeCert.exe is distributed FiddlerCore checks for it first before using the assemblies so as long as MakeCert.exe exists it’ll be used for certificate creation (at least on Windows). Summary FiddlerCore is a pretty sweet tool, and it’s absolutely awesome that we get to plug in most of the functionality of Fiddler right into our own applications. A few years back I tried to build this sort of functionality myself for an app and ended up giving up because it’s a big job to get HTTP right – especially if you need to support SSL. FiddlerCore now provides that functionality as a turnkey solution that can be plugged into your own apps easily. The only downside is FiddlerCore’s documentation for more advanced features like certificate installation which is pretty sketchy. While for the most part FiddlerCore’s feature set is easy to work with without any documentation, advanced features are often not intuitive to gleam by just using Intellisense or the FiddlerCore help file reference (which is not terribly useful). While Eric Lawrence is very responsive on his forum and on Twitter, there simply isn’t much useful documentation on Fiddler/FiddlerCore available online. If you run into trouble the forum is probably the first place to look and then ask a question if you can’t find the answer. The best documentation you can find is Eric’s Fiddler Book which covers a ton of functionality of Fiddler and FiddlerCore. The book is a great reference to Fiddler’s feature set as well as providing great insights into the HTTP protocol. The second half of the book that gets into the innards of HTTP is an excellent read for anybody who wants to know more about some of the more arcane aspects and special behaviors of HTTP – it’s well worth the read. While the book has tons of information in a very readable format, it’s unfortunately not a great reference as it’s hard to find things in the book and because it’s not available online you can’t electronically search for the great content in it. But it’s hard to complain about any of this given the obvious effort and love that’s gone into this awesome product for all of these years. A mighty big thanks to Eric Lawrence  for having created this useful tool that so many of us use all the time, and also to Telerik for picking up Fiddler/FiddlerCore and providing Eric the resources to support and improve this wonderful tool full time and keeping it free for all. Kudos! Resources FiddlerCore Download FiddlerCore NuGet Fiddler Capture Sample Form Fiddler Capture Form in West Wind WebSurge (GitHub) Eric Lawrence’s Fiddler Book© Rick Strahl, West Wind Technologies, 2005-2014Posted in .NET  HTTP   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

  Read the article

• Why is Java EE 6 better than Spring ?

  - by arungupta

  Java EE 6 was released over 2 years ago and now there are 14 compliant application servers. In all my talks around the world, a question that is frequently asked is Why should I use Java EE 6 instead of Spring ? There are already several blogs covering that topic: Java EE wins over Spring by Bill Burke Why will I use Java EE instead of Spring in new Enterprise Java projects in 2012 ? by Kai Waehner (more discussion on TSS) Spring to Java EE migration (Part 1 and 2, 3 and 4 coming as well) by David Heffelfinger Spring to Java EE - A Migration Experience by Lincoln Baxter Migrating Spring to Java EE 6 by Bert Ertman and Paul Bakker at NLJUG Moving from Spring to Java EE 6 - The Age of Frameworks is Over at TSS Java EE vs Spring Shootout by Rohit Kelapure and Reza Rehman at JavaOne 2011 Java EE 6 and the Ewoks by Murat Yener Definite excuse to avoid Spring forever - Bert Ertman and Arun Gupta I will try to share my perspective in this blog. First of all, I'd like to start with a note: Thank you Spring framework for filling the interim gap and providing functionality that is now included in the mainstream Java EE 6 application servers. The Java EE platform has evolved over the years learning from frameworks like Spring and provides all the functionality to build an enterprise application. Thank you very much Spring framework! While Spring was revolutionary in its time and is still very popular and quite main stream in the same way Struts was circa 2003, it really is last generation's framework - some people are even calling it legacy. However my theory is "code is king". So my approach is to build/take a simple Hello World CRUD application in Java EE 6 and Spring and compare the deployable artifacts. I started looking at the official tutorial Developing a Spring Framework MVC Application Step-by-Step but it is using the older version 2.5. I wasn't able to find any updated version in the current 3.1 release. Next, I downloaded Spring Tool Suite and thought that would provide some template samples to get started. A least a quick search did not show any handy tutorials - either video or text-based. So I searched and found a link to their SVN repository at src.springframework.org/svn/spring-samples/. I tried the "mvc-basic" sample and the generated WAR file was 4.43 MB. While it was named a "basic" sample it seemed to come with 19 different libraries bundled but it was what I could find: ./WEB-INF/lib/aopalliance-1.0.jar./WEB-INF/lib/hibernate-validator-4.1.0.Final.jar./WEB-INF/lib/jcl-over-slf4j-1.6.1.jar./WEB-INF/lib/joda-time-1.6.2.jar./WEB-INF/lib/joda-time-jsptags-1.0.2.jar./WEB-INF/lib/jstl-1.2.jar./WEB-INF/lib/log4j-1.2.16.jar./WEB-INF/lib/slf4j-api-1.6.1.jar./WEB-INF/lib/slf4j-log4j12-1.6.1.jar./WEB-INF/lib/spring-aop-3.0.5.RELEASE.jar./WEB-INF/lib/spring-asm-3.0.5.RELEASE.jar./WEB-INF/lib/spring-beans-3.0.5.RELEASE.jar./WEB-INF/lib/spring-context-3.0.5.RELEASE.jar./WEB-INF/lib/spring-context-support-3.0.5.RELEASE.jar./WEB-INF/lib/spring-core-3.0.5.RELEASE.jar./WEB-INF/lib/spring-expression-3.0.5.RELEASE.jar./WEB-INF/lib/spring-web-3.0.5.RELEASE.jar./WEB-INF/lib/spring-webmvc-3.0.5.RELEASE.jar./WEB-INF/lib/validation-api-1.0.0.GA.jar And it is not even using any database! The app deployed fine on GlassFish 3.1.2 but the "@Controller Example" link did not work as it was missing the context root. With a bit of tweaking I could deploy the application and assume that the account got created because no error was displayed in the browser or server log. Next I generated the WAR for "mvc-ajax" and the 5.1 MB WAR had 20 JARs (1 removed, 2 added): ./WEB-INF/lib/aopalliance-1.0.jar./WEB-INF/lib/hibernate-validator-4.1.0.Final.jar./WEB-INF/lib/jackson-core-asl-1.6.4.jar./WEB-INF/lib/jackson-mapper-asl-1.6.4.jar./WEB-INF/lib/jcl-over-slf4j-1.6.1.jar./WEB-INF/lib/joda-time-1.6.2.jar./WEB-INF/lib/jstl-1.2.jar./WEB-INF/lib/log4j-1.2.16.jar./WEB-INF/lib/slf4j-api-1.6.1.jar./WEB-INF/lib/slf4j-log4j12-1.6.1.jar./WEB-INF/lib/spring-aop-3.0.5.RELEASE.jar./WEB-INF/lib/spring-asm-3.0.5.RELEASE.jar./WEB-INF/lib/spring-beans-3.0.5.RELEASE.jar./WEB-INF/lib/spring-context-3.0.5.RELEASE.jar./WEB-INF/lib/spring-context-support-3.0.5.RELEASE.jar./WEB-INF/lib/spring-core-3.0.5.RELEASE.jar./WEB-INF/lib/spring-expression-3.0.5.RELEASE.jar./WEB-INF/lib/spring-web-3.0.5.RELEASE.jar./WEB-INF/lib/spring-webmvc-3.0.5.RELEASE.jar./WEB-INF/lib/validation-api-1.0.0.GA.jar 2 more JARs for just doing Ajax. Anyway, deploying this application gave the following error: Caused by: java.lang.NoSuchMethodError: org.codehaus.jackson.map.SerializationConfig.<init>(Lorg/codehaus/jackson/map/ClassIntrospector;Lorg/codehaus/jackson/map/AnnotationIntrospector;Lorg/codehaus/jackson/map/introspect/VisibilityChecker;Lorg/codehaus/jackson/map/jsontype/SubtypeResolver;)V    at org.springframework.samples.mvc.ajax.json.ConversionServiceAwareObjectMapper.<init>(ConversionServiceAwareObjectMapper.java:20)    at org.springframework.samples.mvc.ajax.json.JacksonConversionServiceConfigurer.postProcessAfterInitialization(JacksonConversionServiceConfigurer.java:40)    at org.springframework.beans.factory.support.AbstractAutowireCapableBeanFactory.applyBeanPostProcessorsAfterInitialization(AbstractAutowireCapableBeanFactory.java:407) Seems like some incorrect repos in the "pom.xml". Next one is "mvc-showcase" and the 6.49 MB WAR now has 28 JARs as shown below: ./WEB-INF/lib/aopalliance-1.0.jar./WEB-INF/lib/aspectjrt-1.6.10.jar./WEB-INF/lib/commons-fileupload-1.2.2.jar./WEB-INF/lib/commons-io-2.0.1.jar./WEB-INF/lib/el-api-2.2.jar./WEB-INF/lib/hibernate-validator-4.1.0.Final.jar./WEB-INF/lib/jackson-core-asl-1.8.1.jar./WEB-INF/lib/jackson-mapper-asl-1.8.1.jar./WEB-INF/lib/javax.inject-1.jar./WEB-INF/lib/jcl-over-slf4j-1.6.1.jar./WEB-INF/lib/jdom-1.0.jar./WEB-INF/lib/joda-time-1.6.2.jar./WEB-INF/lib/jstl-api-1.2.jar./WEB-INF/lib/jstl-impl-1.2.jar./WEB-INF/lib/log4j-1.2.16.jar./WEB-INF/lib/rome-1.0.0.jar./WEB-INF/lib/slf4j-api-1.6.1.jar./WEB-INF/lib/slf4j-log4j12-1.6.1.jar./WEB-INF/lib/spring-aop-3.1.0.RELEASE.jar./WEB-INF/lib/spring-asm-3.1.0.RELEASE.jar./WEB-INF/lib/spring-beans-3.1.0.RELEASE.jar./WEB-INF/lib/spring-context-3.1.0.RELEASE.jar./WEB-INF/lib/spring-context-support-3.1.0.RELEASE.jar./WEB-INF/lib/spring-core-3.1.0.RELEASE.jar./WEB-INF/lib/spring-expression-3.1.0.RELEASE.jar./WEB-INF/lib/spring-web-3.1.0.RELEASE.jar./WEB-INF/lib/spring-webmvc-3.1.0.RELEASE.jar./WEB-INF/lib/validation-api-1.0.0.GA.jar The app at least deployed and showed results this time. But still no database! Next I tried building "jpetstore" and got the error: [ERROR] Failed to execute goal on project org.springframework.samples.jpetstore:Could not resolve dependencies for project org.springframework.samples:org.springframework.samples.jpetstore:war:1.0.0-SNAPSHOT: Failed to collect dependencies for [commons-fileupload:commons-fileupload:jar:1.2.1 (compile), org.apache.struts:com.springsource.org.apache.struts:jar:1.2.9 (compile), javax.xml.rpc:com.springsource.javax.xml.rpc:jar:1.1.0 (compile), org.apache.commons:com.springsource.org.apache.commons.dbcp:jar:1.2.2.osgi (compile), commons-io:commons-io:jar:1.3.2 (compile), hsqldb:hsqldb:jar:1.8.0.7 (compile), org.apache.tiles:tiles-core:jar:2.2.0 (compile), org.apache.tiles:tiles-jsp:jar:2.2.0 (compile), org.tuckey:urlrewritefilter:jar:3.1.0 (compile), org.springframework:spring-webmvc:jar:3.0.0.BUILD-SNAPSHOT (compile), org.springframework:spring-orm:jar:3.0.0.BUILD-SNAPSHOT (compile), org.springframework:spring-context-support:jar:3.0.0.BUILD-SNAPSHOT (compile), org.springframework.webflow:spring-js:jar:2.0.7.RELEASE (compile), org.apache.ibatis:com.springsource.com.ibatis:jar:2.3.4.726 (runtime), com.caucho:com.springsource.com.caucho:jar:3.2.1 (compile), org.apache.axis:com.springsource.org.apache.axis:jar:1.4.0 (compile), javax.wsdl:com.springsource.javax.wsdl:jar:1.6.1 (compile), javax.servlet:jstl:jar:1.2 (runtime), org.aspectj:aspectjweaver:jar:1.6.5 (compile), javax.servlet:servlet-api:jar:2.5 (provided), javax.servlet.jsp:jsp-api:jar:2.1 (provided), junit:junit:jar:4.6 (test)]: Failed to read artifact descriptor for org.springframework:spring-webmvc:jar:3.0.0.BUILD-SNAPSHOT: Could not transfer artifact org.springframework:spring-webmvc:pom:3.0.0.BUILD-SNAPSHOT from/to JBoss repository (http://repository.jboss.com/maven2): Access denied to: http://repository.jboss.com/maven2/org/springframework/spring-webmvc/3.0.0.BUILD-SNAPSHOT/spring-webmvc-3.0.0.BUILD-SNAPSHOT.pom It appears the sample is broken - maybe I was pulling from the wrong repository - would be great if someone were to point me at a good target to use here. With a 50% hit on samples in this repository, I started searching through numerous blogs, most of which have either outdated information (using XML-heavy Spring 2.5), some piece of configuration (which is a typical "feature" of Spring) is missing, or too much complexity in the sample. I finally found this blog that worked like a charm. This blog creates a trivial Spring MVC 3 application using Hibernate and MySQL. This application performs CRUD operations on a single table in a database using typical Spring technologies.  I downloaded the sample code from the blog, deployed it on GlassFish 3.1.2 and could CRUD the "person" entity. The source code for this application can be downloaded here. More details on the application statistics below. And then I built a similar CRUD application in Java EE 6 using NetBeans wizards in a couple of minutes. The source code for the application can be downloaded here and the WAR here. The Spring Source Tool Suite may also offer similar wizard-driven capabilities but this blog focus primarily on comparing the runtimes. The lack of STS tutorials was slightly disappointing as well. NetBeans however has tons of text-based and video tutorials and tons of material even by the community. One more bit on the download size of tools bundle ... NetBeans 7.1.1 "All" is 211 MB (which includes GlassFish and Tomcat) Spring Tool Suite  2.9.0 is 347 MB (~ 65% bigger) This blog is not about the tooling comparison so back to the Java EE 6 version of the application .... In order to run the Java EE version on GlassFish, copy the MySQL Connector/J to glassfish3/glassfish/domains/domain1/lib/ext directory and create a JDBC connection pool and JDBC resource as: ./bin/asadmin create-jdbc-connection-pool --datasourceclassname \\ com.mysql.jdbc.jdbc2.optional.MysqlDataSource --restype \\ javax.sql.DataSource --property \\ portNumber=3306:user=mysql:password=mysql:databaseName=mydatabase \\ myConnectionPool ./bin/asadmin create-jdbc-resource --connectionpoolid myConnectionPool jdbc/myDataSource I generated WARs for the two projects and the table below highlights some differences between them: Java EE 6 Spring WAR File Size 0.021030 MB 10.87 MB (~516x) Number of files 20 53 (> 2.5x) Bundled libraries 0 36 Total size of libraries 0 12.1 MB XML files 3 5 LoC in XML files 50 (11 + 15 + 24) 129 (27 + 46 + 16 + 11 + 19) (~ 2.5x) Total .properties files 1 Bundle.properties 2 spring.properties, log4j.properties Cold Deploy 5,339 ms 11,724 ms Second Deploy 481 ms 6,261 ms Third Deploy 528 ms 5,484 ms Fourth Deploy 484 ms 5,576 ms Runtime memory ~73 MB ~101 MB Some points worth highlighting from the table ... 516x WAR file, 10x deployment time - With 12.1 MB of libraries (for a very basic application) bundled in your application, the WAR file size and the deployment time will naturally go higher. The WAR file for Spring-based application is 516x bigger and the deployment time is double during the first deployment and ~ 10x during subsequent deployments. The Java EE 6 application is fully portable and will run on any Java EE 6 compliant application server. 36 libraries in the WAR - There are 14 Java EE 6 compliant application servers today. Each of those servers provide all the functionality like transactions, dependency injection, security, persistence, etc typically required of an enterprise or web application. There is no need to bundle 36 libraries worth 12.1 MB for a trivial CRUD application. These 14 compliant application servers provide all the functionality baked in. Now you can also deploy these libraries in the container but then you don't get the "portability" offered by Spring in that case. Does your typical Spring deployment actually do that ? 3x LoC in XML - The number of XML files is about 1.6x and the LoC is ~ 2.5x. So much XML seems circa 2003 when the Java language had no annotations. The XML files can be further reduced, e.g. faces-config.xml can be replaced without providing i18n, but I just want to compare stock applications. Memory usage - Both the applications were deployed on default GlassFish 3.1.2 installation and any additional memory consumed as part of deployment/access was attributed to the application. This is by no means scientific but at least provides an initial ballpark. This area definitely needs more investigation. Another table that compares typical Java EE 6 compliant application servers and the custom-stack created for a Spring application ... Java EE 6 Spring Web Container ? 53 MB (tcServer 2.6.3 Developer Edition) Security ? 12 MB (Spring Security 3.1.0) Persistence ? 6.3 MB (Hibernate 4.1.0, required) Dependency Injection ? 5.3 MB (Framework) Web Services ? 796 KB (Spring WS 2.0.4) Messaging ? 3.4 MB (RabbitMQ Server 2.7.1) 936 KB (Java client 936) OSGi ? 1.3 MB (Spring OSGi 1.2.1) GlassFish and WebLogic (starting at 33 MB) 83.3 MB There are differentiating factors on both the stacks. But most of the functionality like security, persistence, and dependency injection is baked in a Java EE 6 compliant application server but needs to be individually managed and patched for a Spring application. This very quickly leads to a "stack explosion". The Java EE 6 servers are tested extensively on a variety of platforms in different combinations whereas a Spring application developer is responsible for testing with different JDKs, Operating Systems, Versions, Patches, etc. Oracle has both the leading OSS lightweight server with GlassFish and the leading enterprise Java server with WebLogic Server, both Java EE 6 and both with lightweight deployment options. The Web Container offered as part of a Java EE 6 application server not only deploys your enterprise Java applications but also provide operational management, diagnostics, and mission-critical capabilities required by your applications. The Java EE 6 platform also introduced the Web Profile which is a subset of the specifications from the entire platform. It is targeted at developers of modern web applications offering a reasonably complete stack, composed of standard APIs, and is capable out-of-the-box of addressing the needs of a large class of Web applications. As your applications grow, the stack can grow to the full Java EE 6 platform. The GlassFish Server Web Profile starting at 33MB (smaller than just the non-standard tcServer) provides most of the functionality typically required by a web application. WebLogic provides battle-tested functionality for a high throughput, low latency, and enterprise grade web application. No individual managing or patching, all tested and commercially supported for you! Note that VMWare does have a server, tcServer, but it is non-standard and not even certified to the level of the standard Web Profile most customers expect these days. Customers who choose this risk proprietary lock-in since VMWare does not seem to want to formally certify with either Java EE 6 Enterprise Platform or with Java EE 6 Web Profile but of course it would be great if they were to join the community and help their customers reduce the risk of deploying on VMWare software. Some more points to help you decide choose between Java EE 6 and Spring ... Freedom to choose container - There are 14 Java EE 6 compliant application servers today, with a variety of open source and commercial offerings. A Java EE 6 application can be deployed on any of those containers. So if you deployed your application on GlassFish today and would like to scale up with your demands then you can deploy the same application to WebLogic. And because of the portability of a Java EE 6 application, you can even take it a different vendor altogether. Spring requires a runtime which could be any of these app servers as well. But why use Spring when all the required functionality is already baked into the application server itself ? Spring also has a different definition of portability where they claim to bundle all the libraries in the WAR file and move to any application server. But we saw earlier how bloated that archive could be. The equivalent features in Spring runtime offerings (mainly tcServer) are not all open source, not as mature, and often require manual assembly.  Vendor choice - The Java EE 6 platform is created using the Java Community Process where all the big players like Oracle, IBM, RedHat, and Apache are conritbuting to make the platform successful. Each application server provides the basic Java EE 6 platform compliance and has its own competitive offerings. This allows you to choose an application server for deploying your Java EE 6 applications. If you are not happy with the support or feature of one vendor then you can move your application to a different vendor because of the portability promise offered by the platform. Spring is a set of products from a single company, one price book, one support organization, one sustaining organization, one sales organization, etc. If any of those cause a customer headache, where do you go ? Java EE, backed by multiple vendors, is a safer bet for those that are risk averse. Production support - With Spring, typically you need to get support from two vendors - VMWare and the container provider. With Java EE 6, all of this is typically provided by one vendor. For example, Oracle offers commercial support from systems, operating systems, JDK, application server, and applications on top of them. VMWare certainly offers complete production support but do you really want to put all your eggs in one basket ? Do you really use tcServer ? ;-) Maintainability - With Spring, you are likely building your own distribution with multiple JAR files, integrating, patching, versioning, etc of all those components. Spring's claim is that multiple JAR files allow you to go à la carte and pick the latest versions of different components. But who is responsible for testing whether all these versions work together ? Yep, you got it, its YOU! If something does not work, who patches and maintains the JARs ? Of course, you! Commercial support for such a configuration ? On your own! The Java EE application servers manage all of this for you and provide a well-tested and commercially supported bundle. While it is always good to realize that there is something new and improved that updates and replaces older frameworks like Spring, the good news is not only does a Java EE 6 container offer what is described here, most also will let you deploy and run your Spring applications on them while you go through an upgrade to a more modern architecture. End result, you get the best of both worlds - keeping your legacy investment but moving to a more agile, lightweight world of Java EE 6. A message to the Spring lovers ... The complexity in J2EE 1.2, 1.3, and 1.4 led to the genesis of Spring but that was in 2004. This is 2012 and the name has changed to "Java EE 6" :-) There are tons of improvements in the Java EE platform to make it easy-to-use and powerful. Some examples: Adding @Stateless on a POJO makes it an EJB EJBs can be packaged in a WAR with no special packaging or deployment descriptors "web.xml" and "faces-config.xml" are optional in most of the common cases Typesafe dependency injection is now part of the Java EE platform Add @Path on a POJO allows you to publish it as a RESTful resource EJBs can be used as backing beans for Facelets-driven JSF pages providing full MVC Java EE 6 WARs are known to be kilobytes in size and deployed in milliseconds Tons of other simplifications in the platform and application servers So if you moved away from J2EE to Spring many years ago and have not looked at Java EE 6 (which has been out since Dec 2009) then you should definitely try it out. Just be at least aware of what other alternatives are available instead of restricting yourself to one stack. Here are some workshops and screencasts worth trying: screencast #37 shows how to build an end-to-end application using NetBeans screencast #36 builds the same application using Eclipse javaee-lab-feb2012.pdf is a 3-4 hours self-paced hands-on workshop that guides you to build a comprehensive Java EE 6 application using NetBeans Each city generally has a "spring cleanup" program every year. It allows you to clean up the mess from your house. For your software projects, you don't need to wait for an annual event, just get started and reduce the technical debt now! Move away from your legacy Spring-based applications to a lighter and more modern approach of building enterprise Java applications using Java EE 6. Watch this beautiful presentation that explains how to migrate from Spring -> Java EE 6: List of files in the Java EE 6 project: ./index.xhtml./META-INF./person./person/Create.xhtml./person/Edit.xhtml./person/List.xhtml./person/View.xhtml./resources./resources/css./resources/css/jsfcrud.css./template.xhtml./WEB-INF./WEB-INF/classes./WEB-INF/classes/Bundle.properties./WEB-INF/classes/META-INF./WEB-INF/classes/META-INF/persistence.xml./WEB-INF/classes/org./WEB-INF/classes/org/javaee./WEB-INF/classes/org/javaee/javaeemysql./WEB-INF/classes/org/javaee/javaeemysql/AbstractFacade.class./WEB-INF/classes/org/javaee/javaeemysql/Person.class./WEB-INF/classes/org/javaee/javaeemysql/Person_.class./WEB-INF/classes/org/javaee/javaeemysql/PersonController$1.class./WEB-INF/classes/org/javaee/javaeemysql/PersonController$PersonControllerConverter.class./WEB-INF/classes/org/javaee/javaeemysql/PersonController.class./WEB-INF/classes/org/javaee/javaeemysql/PersonFacade.class./WEB-INF/classes/org/javaee/javaeemysql/util./WEB-INF/classes/org/javaee/javaeemysql/util/JsfUtil.class./WEB-INF/classes/org/javaee/javaeemysql/util/PaginationHelper.class./WEB-INF/faces-config.xml./WEB-INF/web.xml List of files in the Spring 3.x project: ./META-INF ./META-INF/MANIFEST.MF./WEB-INF./WEB-INF/applicationContext.xml./WEB-INF/classes./WEB-INF/classes/log4j.properties./WEB-INF/classes/org./WEB-INF/classes/org/krams ./WEB-INF/classes/org/krams/tutorial ./WEB-INF/classes/org/krams/tutorial/controller ./WEB-INF/classes/org/krams/tutorial/controller/MainController.class ./WEB-INF/classes/org/krams/tutorial/domain ./WEB-INF/classes/org/krams/tutorial/domain/Person.class ./WEB-INF/classes/org/krams/tutorial/service ./WEB-INF/classes/org/krams/tutorial/service/PersonService.class ./WEB-INF/hibernate-context.xml ./WEB-INF/hibernate.cfg.xml ./WEB-INF/jsp ./WEB-INF/jsp/addedpage.jsp ./WEB-INF/jsp/addpage.jsp ./WEB-INF/jsp/deletedpage.jsp ./WEB-INF/jsp/editedpage.jsp ./WEB-INF/jsp/editpage.jsp ./WEB-INF/jsp/personspage.jsp ./WEB-INF/lib ./WEB-INF/lib/antlr-2.7.6.jar ./WEB-INF/lib/aopalliance-1.0.jar ./WEB-INF/lib/c3p0-0.9.1.2.jar ./WEB-INF/lib/cglib-nodep-2.2.jar ./WEB-INF/lib/commons-beanutils-1.8.3.jar ./WEB-INF/lib/commons-collections-3.2.1.jar ./WEB-INF/lib/commons-digester-2.1.jar ./WEB-INF/lib/commons-logging-1.1.1.jar ./WEB-INF/lib/dom4j-1.6.1.jar ./WEB-INF/lib/ejb3-persistence-1.0.2.GA.jar ./WEB-INF/lib/hibernate-annotations-3.4.0.GA.jar ./WEB-INF/lib/hibernate-commons-annotations-3.1.0.GA.jar ./WEB-INF/lib/hibernate-core-3.3.2.GA.jar ./WEB-INF/lib/javassist-3.7.ga.jar ./WEB-INF/lib/jstl-1.1.2.jar ./WEB-INF/lib/jta-1.1.jar ./WEB-INF/lib/junit-4.8.1.jar ./WEB-INF/lib/log4j-1.2.14.jar ./WEB-INF/lib/mysql-connector-java-5.1.14.jar ./WEB-INF/lib/persistence-api-1.0.jar ./WEB-INF/lib/slf4j-api-1.6.1.jar ./WEB-INF/lib/slf4j-log4j12-1.6.1.jar ./WEB-INF/lib/spring-aop-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-asm-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-beans-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-context-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-context-support-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-core-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-expression-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-jdbc-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-orm-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-tx-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-web-3.0.5.RELEASE.jar ./WEB-INF/lib/spring-webmvc-3.0.5.RELEASE.jar ./WEB-INF/lib/standard-1.1.2.jar ./WEB-INF/lib/xml-apis-1.0.b2.jar ./WEB-INF/spring-servlet.xml ./WEB-INF/spring.properties ./WEB-INF/web.xml So, are you excited about Java EE 6 ? Want to get started now ? Here are some resources: Java EE 6 SDK (including runtime, samples, tutorials etc) GlassFish Server Open Source Edition 3.1.2 (Community) Oracle GlassFish Server 3.1.2 (Commercial) Java EE 6 using WebLogic 12c and NetBeans (Video) Java EE 6 with NetBeans and GlassFish (Video) Java EE with Eclipse and GlassFish (Video)

  Read the article

• SimpleMembership, Membership Providers, Universal Providers and the new ASP.NET 4.5 Web Forms and ASP.NET MVC 4 templates

  - by Jon Galloway

  The ASP.NET MVC 4 Internet template adds some new, very useful features which are built on top of SimpleMembership. These changes add some great features, like a much simpler and extensible membership API and support for OAuth. However, the new account management features require SimpleMembership and won't work against existing ASP.NET Membership Providers. I'll start with a summary of top things you need to know, then dig into a lot more detail. Summary: SimpleMembership has been designed as a replacement for traditional the previous ASP.NET Role and Membership provider system SimpleMembership solves common problems people ran into with the Membership provider system and was designed for modern user / membership / storage needs SimpleMembership integrates with the previous membership system, but you can't use a MembershipProvider with SimpleMembership The new ASP.NET MVC 4 Internet application template AccountController requires SimpleMembership and is not compatible with previous MembershipProviders You can continue to use existing ASP.NET Role and Membership providers in ASP.NET 4.5 and ASP.NET MVC 4 - just not with the ASP.NET MVC 4 AccountController The existing ASP.NET Role and Membership provider system remains supported as is part of the ASP.NET core ASP.NET 4.5 Web Forms does not use SimpleMembership; it implements OAuth on top of ASP.NET Membership The ASP.NET Web Site Administration Tool (WSAT) is not compatible with SimpleMembership The following is the result of a few conversations with Erik Porter (PM for ASP.NET MVC) to make sure I had some the overall details straight, combined with a lot of time digging around in ILSpy and Visual Studio's assembly browsing tools. SimpleMembership: The future of membership for ASP.NET The ASP.NET Membership system was introduces with ASP.NET 2.0 back in 2005. It was designed to solve common site membership requirements at the time, which generally involved username / password based registration and profile storage in SQL Server. It was designed with a few extensibility mechanisms - notably a provider system (which allowed you override some specifics like backing storage) and the ability to store additional profile information (although the additional  profile information was packed into a single column which usually required access through the API). While it's sometimes frustrating to work with, it's held up for seven years - probably since it handles the main use case (username / password based membership in a SQL Server database) smoothly and can be adapted to most other needs (again, often frustrating, but it can work). The ASP.NET Web Pages and WebMatrix efforts allowed the team an opportunity to take a new look at a lot of things - e.g. the Razor syntax started with ASP.NET Web Pages, not ASP.NET MVC. The ASP.NET Web Pages team designed SimpleMembership to (wait for it) simplify the task of dealing with membership. As Matthew Osborn said in his post Using SimpleMembership With ASP.NET WebPages: With the introduction of ASP.NET WebPages and the WebMatrix stack our team has really be focusing on making things simpler for the developer. Based on a lot of customer feedback one of the areas that we wanted to improve was the built in security in ASP.NET. So with this release we took that time to create a new built in (and default for ASP.NET WebPages) security provider. I say provider because the new stuff is still built on the existing ASP.NET framework. So what do we call this new hotness that we have created? Well, none other than SimpleMembership. SimpleMembership is an umbrella term for both SimpleMembership and SimpleRoles. Part of simplifying membership involved fixing some common problems with ASP.NET Membership. Problems with ASP.NET Membership ASP.NET Membership was very obviously designed around a set of assumptions: Users and user information would most likely be stored in a full SQL Server database or in Active Directory User and profile information would be optimized around a set of common attributes (UserName, Password, IsApproved, CreationDate, Comment, Role membership...) and other user profile information would be accessed through a profile provider Some problems fall out of these assumptions. Requires Full SQL Server for default cases The default, and most fully featured providers ASP.NET Membership providers (SQL Membership Provider, SQL Role Provider, SQL Profile Provider) require full SQL Server. They depend on stored procedure support, and they rely on SQL Server cache dependencies, they depend on agents for clean up and maintenance. So the main SQL Server based providers don't work well on SQL Server CE, won't work out of the box on SQL Azure, etc. Note: Cory Fowler recently let me know about these Updated ASP.net scripts for use with Microsoft SQL Azure which do support membership, personalization, profile, and roles. But the fact that we need a support page with a set of separate SQL scripts underscores the underlying problem. Aha, you say! Jon's forgetting the Universal Providers, a.k.a. System.Web.Providers! Hold on a bit, we'll get to those... Custom Membership Providers have to work with a SQL-Server-centric API If you want to work with another database or other membership storage system, you need to to inherit from the provider base classes and override a bunch of methods which are tightly focused on storing a MembershipUser in a relational database. It can be done (and you can often find pretty good ones that have already been written), but it's a good amount of work and often leaves you with ugly code that has a bunch of System.NotImplementedException fun since there are a lot of methods that just don't apply. Designed around a specific view of users, roles and profiles The existing providers are focused on traditional membership - a user has a username and a password, some specific roles on the site (e.g. administrator, premium user), and may have some additional "nice to have" optional information that can be accessed via an API in your application. This doesn't fit well with some modern usage patterns: In OAuth and OpenID, the user doesn't have a password Often these kinds of scenarios map better to user claims or rights instead of monolithic user roles For many sites, profile or other non-traditional information is very important and needs to come from somewhere other than an API call that maps to a database blob What would work a lot better here is a system in which you were able to define your users, rights, and other attributes however you wanted and the membership system worked with your model - not the other way around. Requires specific schema, overflow in blob columns I've already mentioned this a few times, but it bears calling out separately - ASP.NET Membership focuses on SQL Server storage, and that storage is based on a very specific database schema. SimpleMembership as a better membership system As you might have guessed, SimpleMembership was designed to address the above problems. Works with your Schema As Matthew Osborn explains in his Using SimpleMembership With ASP.NET WebPages post, SimpleMembership is designed to integrate with your database schema: All SimpleMembership requires is that there are two columns on your users table so that we can hook up to it – an “ID” column and a “username” column. The important part here is that they can be named whatever you want. For instance username doesn't have to be an alias it could be an email column you just have to tell SimpleMembership to treat that as the “username” used to log in. Matthew's example shows using a very simple user table named Users (it could be named anything) with a UserID and Username column, then a bunch of other columns he wanted in his app. Then we point SimpleMemberhip at that table with a one-liner: WebSecurity.InitializeDatabaseFile("SecurityDemo.sdf", "Users", "UserID", "Username", true); No other tables are needed, the table can be named anything we want, and can have pretty much any schema we want as long as we've got an ID and something that we can map to a username. Broaden database support to the whole SQL Server family While SimpleMembership is not database agnostic, it works across the SQL Server family. It continues to support full SQL Server, but it also works with SQL Azure, SQL Server CE, SQL Server Express, and LocalDB. Everything's implemented as SQL calls rather than requiring stored procedures, views, agents, and change notifications. Note that SimpleMembership still requires some flavor of SQL Server - it won't work with MySQL, NoSQL databases, etc. You can take a look at the code in WebMatrix.WebData.dll using a tool like ILSpy if you'd like to see why - there places where SQL Server specific SQL statements are being executed, especially when creating and initializing tables. It seems like you might be able to work with another database if you created the tables separately, but I haven't tried it and it's not supported at this point. Note: I'm thinking it would be possible for SimpleMembership (or something compatible) to run Entity Framework so it would work with any database EF supports. That seems useful to me - thoughts? Note: SimpleMembership has the same database support - anything in the SQL Server family - that Universal Providers brings to the ASP.NET Membership system. Easy to with Entity Framework Code First The problem with with ASP.NET Membership's system for storing additional account information is that it's the gate keeper. That means you're stuck with its schema and accessing profile information through its API. SimpleMembership flips that around by allowing you to use any table as a user store. That means you're in control of the user profile information, and you can access it however you'd like - it's just data. Let's look at a practical based on the AccountModel.cs class in an ASP.NET MVC 4 Internet project. Here I'm adding a Birthday property to the UserProfile class. [Table("UserProfile")] public class UserProfile { [Key] [DatabaseGeneratedAttribute(DatabaseGeneratedOption.Identity)] public int UserId { get; set; } public string UserName { get; set; } public DateTime Birthday { get; set; } } Now if I want to access that information, I can just grab the account by username and read the value. var context = new UsersContext(); var username = User.Identity.Name; var user = context.UserProfiles.SingleOrDefault(u => u.UserName == username); var birthday = user.Birthday; So instead of thinking of SimpleMembership as a big membership API, think of it as something that handles membership based on your user database. In SimpleMembership, everything's keyed off a user row in a table you define rather than a bunch of entries in membership tables that were out of your control. How SimpleMembership integrates with ASP.NET Membership Okay, enough sales pitch (and hopefully background) on why things have changed. How does this affect you? Let's start with a diagram to show the relationship (note: I've simplified by removing a few classes to show the important relationships): So SimpleMembershipProvider is an implementaiton of an ExtendedMembershipProvider, which inherits from MembershipProvider and adds some other account / OAuth related things. Here's what ExtendedMembershipProvider adds to MembershipProvider: The important thing to take away here is that a SimpleMembershipProvider is a MembershipProvider, but a MembershipProvider is not a SimpleMembershipProvider. This distinction is important in practice: you cannot use an existing MembershipProvider (including the Universal Providers found in System.Web.Providers) with an API that requires a SimpleMembershipProvider, including any of the calls in WebMatrix.WebData.WebSecurity or Microsoft.Web.WebPages.OAuth.OAuthWebSecurity. However, that's as far as it goes. Membership Providers still work if you're accessing them through the standard Membership API, and all of the core stuff  - including the AuthorizeAttribute, role enforcement, etc. - will work just fine and without any change. Let's look at how that affects you in terms of the new templates. Membership in the ASP.NET MVC 4 project templates ASP.NET MVC 4 offers six Project Templates: Empty - Really empty, just the assemblies, folder structure and a tiny bit of basic configuration. Basic - Like Empty, but with a bit of UI preconfigured (css / images / bundling). Internet - This has both a Home and Account controller and associated views. The Account Controller supports registration and login via either local accounts and via OAuth / OpenID providers. Intranet - Like the Internet template, but it's preconfigured for Windows Authentication. Mobile - This is preconfigured using jQuery Mobile and is intended for mobile-only sites. Web API - This is preconfigured for a service backend built on ASP.NET Web API. Out of these templates, only one (the Internet template) uses SimpleMembership. ASP.NET MVC 4 Basic template The Basic template has configuration in place to use ASP.NET Membership with the Universal Providers. You can see that configuration in the ASP.NET MVC 4 Basic template's web.config: <profile defaultProvider="DefaultProfileProvider"> <providers> <add name="DefaultProfileProvider" type="System.Web.Providers.DefaultProfileProvider, System.Web.Providers, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" connectionStringName="DefaultConnection" applicationName="/" /> </providers> </profile> <membership defaultProvider="DefaultMembershipProvider"> <providers> <add name="DefaultMembershipProvider" type="System.Web.Providers.DefaultMembershipProvider, System.Web.Providers, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" connectionStringName="DefaultConnection" enablePasswordRetrieval="false" enablePasswordReset="true" requiresQuestionAndAnswer="false" requiresUniqueEmail="false" maxInvalidPasswordAttempts="5" minRequiredPasswordLength="6" minRequiredNonalphanumericCharacters="0" passwordAttemptWindow="10" applicationName="/" /> </providers> </membership> <roleManager defaultProvider="DefaultRoleProvider"> <providers> <add name="DefaultRoleProvider" type="System.Web.Providers.DefaultRoleProvider, System.Web.Providers, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" connectionStringName="DefaultConnection" applicationName="/" /> </providers> </roleManager> <sessionState mode="InProc" customProvider="DefaultSessionProvider"> <providers> <add name="DefaultSessionProvider" type="System.Web.Providers.DefaultSessionStateProvider, System.Web.Providers, Version=1.0.0.0, Culture=neutral, PublicKeyToken=31bf3856ad364e35" connectionStringName="DefaultConnection" /> </providers> </sessionState> This means that it's business as usual for the Basic template as far as ASP.NET Membership works. ASP.NET MVC 4 Internet template The Internet template has a few things set up to bootstrap SimpleMembership: \Models\AccountModels.cs defines a basic user account and includes data annotations to define keys and such \Filters\InitializeSimpleMembershipAttribute.cs creates the membership database using the above model, then calls WebSecurity.InitializeDatabaseConnection which verifies that the underlying tables are in place and marks initialization as complete (for the application's lifetime) \Controllers\AccountController.cs makes heavy use of OAuthWebSecurity (for OAuth account registration / login / management) and WebSecurity. WebSecurity provides account management services for ASP.NET MVC (and Web Pages) WebSecurity can work with any ExtendedMembershipProvider. There's one in the box (SimpleMembershipProvider) but you can write your own. Since a standard MembershipProvider is not an ExtendedMembershipProvider, WebSecurity will throw exceptions if the default membership provider is a MembershipProvider rather than an ExtendedMembershipProvider. Practical example: Create a new ASP.NET MVC 4 application using the Internet application template Install the Microsoft ASP.NET Universal Providers for LocalDB NuGet package Run the application, click on Register, add a username and password, and click submit You'll get the following execption in AccountController.cs::Register: To call this method, the "Membership.Provider" property must be an instance of "ExtendedMembershipProvider". This occurs because the ASP.NET Universal Providers packages include a web.config transform that will update your web.config to add the Universal Provider configuration I showed in the Basic template example above. When WebSecurity tries to use the configured ASP.NET Membership Provider, it checks if it can be cast to an ExtendedMembershipProvider before doing anything else. So, what do you do? Options: If you want to use the new AccountController, you'll either need to use the SimpleMembershipProvider or another valid ExtendedMembershipProvider. This is pretty straightforward. If you want to use an existing ASP.NET Membership Provider in ASP.NET MVC 4, you can't use the new AccountController. You can do a few things: Replace  the AccountController.cs and AccountModels.cs in an ASP.NET MVC 4 Internet project with one from an ASP.NET MVC 3 application (you of course won't have OAuth support). Then, if you want, you can go through and remove other things that were built around SimpleMembership - the OAuth partial view, the NuGet packages (e.g. the DotNetOpenAuthAuth package, etc.) Use an ASP.NET MVC 4 Internet application template and add in a Universal Providers NuGet package. Then copy in the AccountController and AccountModel classes. Create an ASP.NET MVC 3 project and upgrade it to ASP.NET MVC 4 using the steps shown in the ASP.NET MVC 4 release notes. None of these are particularly elegant or simple. Maybe we (or just me?) can do something to make this simpler - perhaps a NuGet package. However, this should be an edge case - hopefully the cases where you'd need to create a new ASP.NET but use legacy ASP.NET Membership Providers should be pretty rare. Please let me (or, preferably the team) know if that's an incorrect assumption. Membership in the ASP.NET 4.5 project template ASP.NET 4.5 Web Forms took a different approach which builds off ASP.NET Membership. Instead of using the WebMatrix security assemblies, Web Forms uses Microsoft.AspNet.Membership.OpenAuth assembly. I'm no expert on this, but from a bit of time in ILSpy and Visual Studio's (very pretty) dependency graphs, this uses a Membership Adapter to save OAuth data into an EF managed database while still running on top of ASP.NET Membership. Note: There may be a way to use this in ASP.NET MVC 4, although it would probably take some plumbing work to hook it up. How does this fit in with Universal Providers (System.Web.Providers)? Just to summarize: Universal Providers are intended for cases where you have an existing ASP.NET Membership Provider and you want to use it with another SQL Server database backend (other than SQL Server). It doesn't require agents to handle expired session cleanup and other background tasks, it piggybacks these tasks on other calls. Universal Providers are not really, strictly speaking, universal - at least to my way of thinking. They only work with databases in the SQL Server family. Universal Providers do not work with Simple Membership. The Universal Providers packages include some web config transforms which you would normally want when you're using them. What about the Web Site Administration Tool? Visual Studio includes tooling to launch the Web Site Administration Tool (WSAT) to configure users and roles in your application. WSAT is built to work with ASP.NET Membership, and is not compatible with Simple Membership. There are two main options there: Use the WebSecurity and OAuthWebSecurity API to manage the users and roles Create a web admin using the above APIs Since SimpleMembership runs on top of your database, you can update your users as you would any other data - via EF or even in direct database edits (in development, of course)

  Read the article

• SSH problems (ssh_exchange_identification: read: Connection reset by peer)

  - by kSiR

  I was running 11.10 and decided to do the full upgrade and come up to 12.04 after the update SSH (not SSHD) is now misbehaving when attempting to connect to other OpenSSH instances. I say OpenSSH as I am running a DropBear sshd on my router and I am able to connect to it. When attempting to connect to an OpenSSH server risk@skynet:~/.ssh$ ssh -vvv risk@someserver OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/risk/.ssh/config debug3: key names ok: [[email protected],[email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-rsa,ssh-dss] debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to someserver [someserver] port 22. debug1: Connection established. debug1: identity file /home/risk/.ssh/id_rsa type -1 debug1: identity file /home/risk/.ssh/id_rsa-cert type -1 debug1: identity file /home/risk/.ssh/id_dsa type -1 debug1: identity file /home/risk/.ssh/id_dsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/home/risk/.ssh/id_ecdsa" as a RSA1 public key debug1: identity file /home/risk/.ssh/id_ecdsa type 3 debug1: Checking blacklist file /usr/share/ssh/blacklist.ECDSA-521 debug1: Checking blacklist file /etc/ssh/blacklist.ECDSA-521 debug1: identity file /home/risk/.ssh/id_ecdsa-cert type -1 ssh_exchange_identification: read: Connection reset by peer risk@skynet:~/.ssh$ DropBear instance risk@skynet:~/.ssh$ ssh -vvv root@darkness OpenSSH_5.9p1 Debian-5ubuntu1, OpenSSL 1.0.1 14 Mar 2012 debug1: Reading configuration data /home/risk/.ssh/config debug3: key names ok: [[email protected],[email protected],[email protected],[email protected],ecdsa-sha2-nistp256,ecdsa-sha2-nistp384,ecdsa-sha2-nistp521,ssh-rsa,ssh-dss] debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to darkness [192.168.1.1] port 22. debug1: Connection established. debug1: identity file /home/risk/.ssh/id_rsa type -1 debug1: identity file /home/risk/.ssh/id_rsa-cert type -1 debug1: identity file /home/risk/.ssh/id_dsa type -1 debug1: identity file /home/risk/.ssh/id_dsa-cert type -1 debug3: Incorrect RSA1 identifier debug3: Could not load "/home/risk/.ssh/id_ecdsa" as a RSA1 public key debug1: identity file /home/risk/.ssh/id_ecdsa type 3 debug1: Checking blacklist file /usr/share/ssh/blacklist.ECDSA-521 debug1: Checking blacklist file /etc/ssh/blacklist.ECDSA-521 debug1: identity file /home/risk/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version dropbear_0.52 debug1: no match: dropbear_0.52 ... I have googled and ran most ALL fixes recommend both from the Debian and Arch sides and none of them seem to resolve my issue. Any ideas?

  Read the article

• Tools and Utilities for the .NET Developer

  - by mbcrump

  Tweet this list! Add a link to my site to your bookmarks to quickly find this page again! Add me to twitter! This is a list of the tools/utilities that I use to do my job/hobby. I wanted this page to load fast and contain information that only you care about. If I have missed a tool that you like, feel free to contact me and I will add it to the list. Also, this list took a lot of time to complete. Please do not steal my work, if you like the page then please link back to my site. I will keep the links/information updated as new tools/utilities are created.  Windows/.NET Development – This is a list of tools that any Windows/.NET developer should have in his bag. I have used at some point in my career everything listed on this page and below is the tools worth keeping. Name Description License AnkhSVN Subversion support for Visual Studio. It also works with VS2010. Free Aurora XAML Designer One of the best XAML creation tools available. Has a ton of built in templates that you can copy/paste into VS2010. COST/Trial BeyondCompare Beyond Compare 3 is the ideal tool for comparing files and folders on your Windows or Linux system. Visualize changes in your code and carefully reconcile them. COST/Trial BuildIT Automated Task Tool Its main purpose is to automate tasks, whether it is the final packaging of a product, an automated daily build, maybe sending out a mailing list, even backing-up files. Free C Sharper for VB Convert VB to C#. COST CLRProfiler Analyze and improve the behavior of your .NET app. Free CodeRush Direct competitor to ReSharper, contains similar feature. This is one of those decide for yourself. COST/Trial Disk2VHD Disk2vhd is a utility that creates VHD (Virtual Hard Disk - Microsoft's Virtual Machine disk format) versions of physical disks for use in Microsoft Virtual PC or Microsoft Hyper-V virtual machines (VMs). Free Eazfuscator.NET Is a free obfuscator for .NET. The main purpose is to protect intellectual property of software. Free EQATEC Profiler Make your .NET app run faster. No source code changes are needed. Just point the profiler to your app, run the modified code, and get a visual report. COST Expression Studio 3/4 Comes with Web, Blend, Sketch Flow and more. You can create websites, produce beautiful XAML and more. COST/Trial Expresso The award-winning Expresso editor is equally suitable as a teaching tool for the beginning user of regular expressions or as a full-featured development environment for the experienced programmer or web designer with an extensive knowledge of regular expressions. Free Fiddler Fiddler is a web debugging proxy which logs all HTTP(s) traffic between your computer and the internet. Free Firebug Powerful Web development tool. If you build websites, you will need this. Free FxCop FxCop is an application that analyzes managed code assemblies (code that targets the .NET Framework common language runtime) and reports information about the assemblies, such as possible design, localization, performance, and security improvements. Free GAC Browser and Remover Easy way to remove multiple assemblies from the GAC. Assemblies registered by programs like Install Shield can also be removed. Free GAC Util The Global Assembly Cache tool allows you to view and manipulate the contents of the global assembly cache and download cache. Free HelpScribble Help Scribble is a full-featured, easy-to-use help authoring tool for creating help files from start to finish. You can create Win Help (.hlp) files, HTML Help (.chm) files, a printed manual and online documentation (on a web site) all from the same Help Scribble project. COST/Trial IETester IETester is a free Web Browser that allows you to have the rendering and JavaScript engines of IE9 preview, IE8, IE7 IE 6 and IE5.5 on Windows 7, Vista and XP, as well as the installed IE in the same process. Free iTextSharp iText# (iTextSharp) is a port of the iText open source java library for PDF generation written entirely in C# for the .NET platform. Use the iText mailing list to get support. Free Kaxaml Kaxaml is a lightweight XAML editor that gives you a "split view" so you can see both your XAML and your rendered content. Free LINQPad LinqPad lets you interactively query databases in a LINQ. Free Linquer Many programmers are familiar with SQL and will need a help in the transition to LINQ. Sometimes there are complicated queries to be written and Linqer can help by converting SQL scripts to LINQ. COST/Trial LiquidXML Liquid XML Studio 2010 is an advanced XML developers toolkit and IDE, containing all the tools needed for designing and developing XML schema and applications. COST/Trial Log4Net log4net is a tool to help the programmer output log statements to a variety of output targets. log4net is a port of the excellent log4j framework to the .NET runtime. We have kept the framework similar in spirit to the original log4j while taking advantage of new features in the .NET runtime. For more information on log4net see the features document. Free Microsoft Web Platform Installer The Microsoft Web Platform Installer 2.0 (Web PI) is a free tool that makes getting the latest components of the Microsoft Web Platform, including Internet Information Services (IIS), SQL Server Express, .NET Framework and Visual Web Developer easy. Free Mono Development Don't have Visual Studio - no problem! This is an open Source C# and .NET development environment for Linux, Windows, and Mac OS X Free Net Mass Downloader While it’s great that Microsoft has released the .NET Reference Source Code, you can only get it one file at a time while you’re debugging. If you’d like to batch download it for reading or to populate the cache, you’d have to write a program that instantiated and called each method in the Framework Class Library. Fortunately, .NET Mass Downloader comes to the rescue! Free nMap Nmap ("Network Mapper") is a free and open source (license) utility for network exploration or security auditing. Many systems and network administrators also find it useful for tasks such as network inventory, managing service upgrade schedules, and monitoring host or service uptime. Free NoScript (Firefox add-in) The NoScript Firefox extension provides extra protection for Firefox, Flock, Seamonkey and other Mozilla-based browsers: this free, open source add-on allows JavaScript, Java and Flash and other plug-ins to be executed only by trusted web sites of your choice (e.g. your online bank), and provides the most powerful Anti-XSS protection available in a browser. Free NotePad 2 Notepad2, a fast and light-weight Notepad-like text editor with syntax highlighting. This program can be run out of the box without installation, and does not touch your system's registry. Free PageSpy PageSpy is a small add-on for Internet Explorer that allows you to select any element within a webpage, select an option in the context menu, and view detailed information about both the coding behind the page and the element you selected. Free Phrase Express PhraseExpress manages your frequently used text snippets in customizable categories for quick access. Free PowerGui PowerGui is a free community for PowerGUI, a graphical user interface and script editor for Microsoft Windows PowerShell! Free Powershell Comes with Win7, but you can automate tasks by using the .NET Framework. Great for network admins. Free Process Explorer Ever wondered which program has a particular file or directory open? Now you can find out. Process Explorer shows you information about which handles and DLLs processes have opened or loaded. Also, included in the SysInterals Suite. Free Process Monitor Process Monitor is an advanced monitoring tool for Windows that shows real-time file system, Registry and process/thread activity. Free Reflector Explore and analyze compiled .NET assemblies, viewing them in C#, Visual Basic, and IL. This is an Essential for any .NET developer. Free Regular Expression Library Stuck on a Regular Expression but you think someone has already figured it out? Chances are they have. Free Regulator Regulator makes Regular Expressions easy. This is a must have for a .NET Developer. Free RenameMaestro RenameMaestro is probably the easiest batch file renamer you'll find to instantly rename multiple files COST ReSharper The one program that I cannot live without. Supports VS2010 and offers simple refactoring, code analysis/assistance/cleanup/templates. One of the few applications that is worth the $$$. COST/Trial ScrewTurn Wiki ScrewTurn Wiki allows you to create, manage and share wikis. A wiki is a collaboratively-edited, information-centered website: the most famous is Wikipedia. Free SharpDevelop What is #develop? SharpDevelop is a free IDE for C# and VB.NET projects on Microsoft's .NET platform. Free Show Me The Template Show Me The Template is a tool for exploring the templates, be their data, control or items panel, that comes with the controls built into WPF for all 6 themes. Free SnippetCompiler Compiles code snippets without opening Visual Studio. It does not support .NET 4. Free SQL Prompt SQL Prompt is a plug-in that increases how fast you can work with SQL. It provides code-completion for SQL server, reformatting, db schema information and snippets. Awesome! COST/Trial SQLinForm SQLinForm is an automatic SQL code formatter for all major databases  including ORACLE, SQL Server, DB2, UDB, Sybase, Informix, PostgreSQL, Teradata, MySQL, MS Access etc. with over 70 formatting options. COST/OnlineFree SSMS Tools SSMS Tools Pack is an add-in for Microsoft SQL Server Management Studio (SSMS) including SSMS Express. Free Storm STORM is a free and open source tool for testing web services. Free Telerik Code Convertor Convert code from VB to C Sharp and Vice Versa. Free TurtoiseSVN TortoiseSVN is a really easy to use Revision control / version control / source control software for Windows.Since it's not an integration for a specific IDE you can use it with whatever development tools you like. Free UltraEdit UltraEdit is the ideal text, HTML and hex editor, and an advanced PHP, Perl, Java and JavaScript editor for programmers. UltraEdit is also an XML editor including a tree-style XML parser. An industry-award winner, UltraEdit supports disk-based 64-bit file handling (standard) on 32-bit Windows platforms (Windows 2000 and later). COST/Trial Virtual Windows XP Comes with some W7 version and allows you to run WinXP along side W7. Free VirtualBox Virtualization by Sun Microsystems. You can virtualize Windows, Linux and more. Free Visual Log Parser SQL queries against a variety of log files and other system data sources. Free WinMerge WinMerge is an Open Source differencing and merging tool for Windows. WinMerge can compare both folders and files, presenting differences in a visual text format that is easy to understand and handle. Free Wireshark Wireshark is one of the best network protocol analyzer's for Unix and windows. This has been used several times to get me out of a bind. Free XML Notepad 07 Old, but still one of my favorite XML viewers. Free Productivity Tools – This is the list of tools that I use to save time or quickly navigate around Windows. Name Description License AutoHotKey Automate almost anything by sending keystrokes and mouse clicks. You can write a mouse or keyboard macro by hand or use the macro recorder. Free CLCL CLCL is clipboard caching utility. Free Ditto Ditto is an extension to the standard windows clipboard. It saves each item placed on the clipboard allowing you access to any of those items at a later time. Ditto allows you to save any type of information that can be put on the clipboard, text, images, html, custom formats, ..... Free Evernote Remember everything from notes to photos. It will synch between computers/devices. Free InfoRapid Inforapid is a search tool that will display all you search results in a html like browser. If you click on a word in that browser, it will start another search to the word you clicked on. Handy if you want to trackback something to it's true origin. The word you looked for will be highlighted in red. Clicking on the red word will open the containing file in a text based viewer. Clicking on any word in the opened document will start another search on that word. Free KatMouse The prime purpose of the KatMouse utility is to enhance the functionality of mice with a scroll wheel, offering 'universal' scrolling: moving the mouse wheel will scroll the window directly beneath the mouse cursor (not the one with the keyboard focus, which is default on Windows OSes). This is a major increase in the usefulness of the mouse wheel. Free ScreenR Instant Screencast with nothing to download. Works with Mac or PC and free. Free Start++ Start++ is an enhancement for the Start Menu in Windows Vista. It also extends the Run box and the command-line with customizable commands.  For example, typing "w Windows Vista" will take you to the Windows Vista page on Wikipedia! Free Synergy Synergy lets you easily share a single mouse and keyboard between multiple computers with different operating systems, each with its own display, without special hardware. It's intended for users with multiple computers on their desk since each system uses its own monitor(s). Free Texter Texter lets you define text substitution hot strings that, when triggered, will replace hotstring with a larger piece of text. By entering your most commonly-typed snippets of text into Texter, you can save countless keystrokes in the course of the day. Free Total Commander File handling, FTP, Archive handling and much more. Even works with Win3.11. COST/Trial Available Wizmouse WizMouse is a mouse enhancement utility that makes your mouse wheel work on the window currently under the mouse pointer, instead of the currently focused window. This means you no longer have to click on a window before being able to scroll it with the mouse wheel. This is a far more comfortable and practical way to make use of the mouse wheel. Free Xmarks Bookmark sync and search between computers. Free General Utilities – This is a list for power user users or anyone that wants more out of Windows. I usually install a majority of these whenever I get a new system. Name Description License µTorrent µTorrent is a lightweight and efficient BitTorrent client for Windows or Mac with many features. I use this for downloading LEGAL media. Free Audacity Audacity® is free, open source software for recording and editing sounds. It is available for Mac OS X, Microsoft Windows, GNU/Linux, and other operating systems. Learn more about Audacity... Also check our Wiki and Forum for more information. Free AVast Free FREE Antivirus. Free CD Burner XP Pro CDBurnerXP is a free application to burn CDs and DVDs, including Blu-Ray and HD-DVDs. It also includes the feature to burn and create ISOs, as well as a multilanguage interface. Free CDEX You can extract digital audio CDs into mp3/wav. Free Combofix Combofix is a freeware (a legitimate spyware remover created by sUBs), Combofix was designed to scan a computer for known malware, spyware (SurfSideKick, QooLogic, and Look2Me as well as any other combination of the mentioned spyware applications) and remove them. Free Cpu-Z Provides information about some of the main devices of your system. Free Cropper Cropper is a screen capture utility written in C#. It makes it fast and easy to grab parts of your screen. Use it to easily crop out sections of vector graphic files such as Fireworks without having to flatten the files or open in a new editor. Use it to easily capture parts of a web site, including text and images. It's also great for writing documentation that needs images of your application or web site. Free DropBox Drag and Drop files to sync between computers. Free DVD-Fab Converts/Copies DVDs/Blu-Ray to different formats. (like mp4, mkv, avi) COST/Trial Available FastStone Capture FastStone Capture is a powerful, lightweight, yet full-featured screen capture tool that allows you to easily capture and annotate anything on the screen including windows, objects, menus, full screen, rectangular/freehand regions and even scrolling windows/web pages. Free ffdshow FFDShow is a DirectShow decoding filter for decompressing DivX, XviD, H.264, FLV1, WMV, MPEG-1 and MPEG-2, MPEG-4 movies. Free Filezilla FileZilla Client is a fast and reliable cross-platform FTP, FTPS and SFTP client with lots of useful features and an intuitive graphical user interface. You can also download a server version. Free FireFox Web Browser, do you really need an explanation? Free FireGestures A customizable mouse gestures extension which enables you to execute various commands and user scripts with five types of gestures. Free FoxIt Reader Light weight PDF viewer. You should install this with the advanced setting or it will install a toolbar and setup some shortcuts. Free gSynchIt Synch Gmail and Outlook. Even supports Outlook 2010 32/64 bit COST/Trial Available Hulu Desktop At home or in a hotel, this has replaced my cable/satellite subscription. Free ImgBurn ImgBurn is a lightweight CD / DVD / HD DVD / Blu-ray burning application that everyone should have in their toolkit! Free Infrarecorder InfraRecorder is a free CD/DVD burning solution for Microsoft Windows. It offers a wide range of powerful features; all through an easy to use application interface and Windows Explorer integration. Free KeePass KeePass is a free open source password manager, which helps you to manage your passwords in a secure way. Free LastPass Another password management, synchronize between browsers, automatic form filling and more. Free Live Essentials One download and lots of programs including Mail, Live Writer, Movie Maker and more! Free Monitores MonitorES is a small windows utility that helps you to turnoff monitor display when you lock down your machine.Also when you lock your machine, it will pause all your running media programs & set your IM status message to "Away" / Custom message(via options) and restore it back to normal when you back. Free mRemote mRemote is a full-featured, multi-tab remote connections manager. Free Open Office OpenOffice.org 3 is the leading open-source office software suite for word processing, spreadsheets, presentations, graphics, databases and more. It is available in many languages and works on all common computers. It stores all your data in an international open standard format and can also read and write files from other common office software packages. It can be downloaded and used completely free of charge for any purpose. Free Paint.NET Simple, intuitive, and innovative user interface for editing photos. Free Picasa Picasa is free photo editing software from Google that makes your pictures look great. Free Pidgin Pidgin is an easy to use and free chat client used by millions. Connect to AIM, MSN, Yahoo, and more chat networks all at once. Free PING PING is a live Linux ISO, based on the excellent Linux From Scratch (LFS) documentation. It can be burnt on a CD and booted, or integrated into a PXE / RIS environment. Free Putty PuTTY is an SSH and telnet client, developed originally by Simon Tatham for the Windows platform. Free Revo Uninstaller Revo Uninstaller Pro helps you to uninstall software and remove unwanted programs installed on your computer easily! Even if you have problems uninstalling and cannot uninstall them from "Windows Add or Remove Programs" control panel applet.Revo Uninstaller is a much faster and more powerful alternative to "Windows Add or Remove Programs" applet! It has very powerful features to uninstall and remove programs. Free Security Essentials Microsoft Security Essentials is a new, free consumer anti-malware solution for your computer. Free SetupVirtualCloneDrive Virtual CloneDrive works and behaves just like a physical CD/DVD drive, however it exists only virtually. Point to the .ISO file and it appears in Windows Explorer as a Drive. Free Shark 007 Codec Pack Play just about any file format with this download. Also includes my W7 Media Playlist Generator. Free Snagit 9 Screen Capture on steroids. Add arrows, captions, etc to any screenshot. COST/Trial Available SysinternalsSuite Go ahead and download the entire sys internals suite. I have mentioned multiple programs in this suite already. Free TeraCopy TeraCopy is a compact program designed to copy and move files at the maximum possible speed, providing the user with a lot of features. Free for Home TrueCrypt Free open-source disk encryption software for Windows 7/Vista/XP, Mac OS X, and Linux Free TweetDeck Fully featured Twitter client. Free UltraVNC UltraVNC is a powerful, easy to use and free software that can display the screen of another computer (via internet or network) on your own screen. The program allows you to use your mouse and keyboard to control the other PC remotely. It means that you can work on a remote computer, as if you were sitting in front of it, right from your current location. Free Unlocker Unlocks locked files. Pretty simple right? Free VLC Media Player VLC media player is a highly portable multimedia player and multimedia framework capable of reading most audio and video formats Free Windows 7 Media Playlist This program is special to my heart because I wrote it. It has been mentioned on podcast and various websites. It allows you to quickly create wvx video playlist for Windows Media Center. Free WinRAR WinRAR is a powerful archive manager. It can backup your data and reduce the size of email attachments, decompress RAR, ZIP and other files downloaded from Internet and create new archives in RAR and ZIP file format. COST/Trial Available Blogging – I use the following for my blog. Name Description License Insert Code for Windows Live Writer Insert Code for Windows Live Writer will format a snippet of text in a number of programming languages such as C#, HTML, MSH, JavaScript, Visual Basic and TSQL. Free LiveWriter Included in Live Essentials, but the ultimate in Windows Blogging Free PasteAsVSCode Plug-in for Windows Live Writer that pastes clipboard content as Visual Studio code. Preserves syntax highlighting, indentation and background color. Converts RTF, outputted by Visual Studio, into HTML. Free Desktop Management – The list below represent the best in Windows Desktop Management. Name Description License 7 Stacks Allows users to have "stacks" of icons in their taskbar. Free Executor Executor is a multi purpose launcher and a more advanced and customizable version of windows run. Free Fences Fences is a program that helps you organize your desktop and can hide your icons when they are not in use. Free RocketDock Rocket Dock is a smoothly animated, alpha blended application launcher. It provides a nice clean interface to drop shortcuts on for easy access and organization. With each item completely customizable there is no end to what you can add and launch from the dock. Free WindowsTab Tabbing is an essential feature of modern web browsers. Window Tabs brings the productivity of tabbed window management to all of your desktop applications. Free

  Read the article

• va_getDriverName() failed with unknown

  - by MIkCode

  i upgraded to 14.04 and afterwards i got an issue with cpu usage when playing HD. I checked the vainfo and this what i got back ibva info: VA-API version 0.35.0 libva info: va_getDriverName() returns -1 libva error: va_getDriverName() failed with unknown libva error,driver_name=(null) vaInitialize failed with error code -1 (unknown libva error),exit I re install the driver sudo apt-get --reinstall install i965-va-driver but i steel got the same error. Any thoghts

  Read the article

• How To Activate Your Free Office 2007 to 2010 Tech Guarantee Upgrade

  - by Matthew Guay

  Have you purchased Office 2007 since March 5th, 2010?  If so, here’s how you can activate and download your free upgrade to Office 2010! Microsoft Office 2010 has just been released, and today you can purchase upgrades from most retail stores or directly from Microsoft via download.  But if you’ve purchased a new copy of Office 2007 or a new computer that came with Office 2007 since March 5th, 2010, then you’re entitled to an absolutely free upgrade to Office 2010.  You’ll need enter information about your Office 2007 and then download the upgrade, so we’ll step you through the process. Getting Started First, if you’ve recently purchased Office 2007 but haven’t installed it, you’ll need to go ahead and install it before you can get your free Office 2010 upgrade.  Install it as normal.   Once Office 2007 is installed, run any of the Office programs.  You’ll be prompted to activate Office.  Make sure you’re connected to the internet, and then click Next to activate. Get your Free Upgrade to Office 2010 Now you’re ready to download your upgrade to Office 2010.  Head to the Office Tech Guarantee site (link below), and click Upgrade now. You’ll need to enter some information about your Office 2007.  Check that you purchased your copy of Office 2007 after March 5th, select your computer manufacturer, and check that you agree to the terms. Now you’re going to need the Product ID number from Office 2007.  To find this, open Word or any other Office 2007 application.  Click the Office Orb, and select Options on the bottom. Select the Resources button on the left, and then click About. Near the bottom of this dialog, you’ll see your Product ID.  This should be a number like: 12345-123-1234567-12345   Go back to the Office Tech Guarantee signup page in your browser, and enter this Product ID.  Select the language of your edition of Office 2007, enter the verification code, and then click Submit. It may take a few moments to validate your Product ID. When it is finished, you’ll be taken to an order page that shows the edition of Office 2010 you’re eligible to receive.  The upgrade download is free, but if you’d like to purchase a backup DVD of Office 2010, you can add it to your order for $13.99.  Otherwise, simply click Continue to accept. Do note that the edition of Office 2010 you receive may be different that the edition of Office 2007 you purchased, as the number of editions has been streamlined in the Office 2010 release.  Here’s a chart you can check to see what edition you’ll receive.  Note that you’ll still be allowed to install Office on the same number of computers; for example, Office 2007 Home and Student allows you to install it on up to 3 computers in the same house, and your Office 2010 upgrade will allow the same. Office 2007 Edition Office 2010 Upgrade You’ll Receive Office 2007 Home and Student Office Home and Student 2010 Office Basic 2007Office Standard 2007 Office Home and Business 2010 Office Small Business 2007Office Professional 2007Office Ultimate 2007 Office Professional 2010 Office Professional 2007 AcademicOffice Ultimate 2007 Academic Office Professional Academic 2010 Sign in with your Windows Live ID, or create a new one if you don’t already have one. Enter your name, select your country, and click Create My Account.  Note that Office will send Office 2010 tips to your email address; if you don’t wish to receive them, you can unsubscribe from the emails later.   Finally, you’re ready to download Office 2010!  Click the Download Now link to start downloading Office 2010.  Your Product Key will appear directly above the Download link, so you can copy it and then paste it in the installer when your download is finished.  You will additionally receive an email with the download links and product key, so if your download fails you can always restart it from that link. If your edition of Office 2007 included the Office Business Contact Manager, you will be able to download it from the second Download link.  And, of course, even if you didn’t order a backup DVD, you can always burn the installers to a DVD for a backup.   Install Office 2010 Once you’re finished downloading Office 2010, run the installer to get it installed on your computer.  Enter your Product Key from the Tech Guarantee website as above, and click Continue. Accept the license agreement, and then click Upgrade to upgrade to the latest version of Office.   The installer will remove all of your Office 2007 applications, and then install their 2010 counterparts.  If you wish to keep some of your Office 2007 applications instead, click Customize and then select to either keep all previous versions or simply keep specific applications. By default, Office 2010 will try to activate online automatically.  If it doesn’t activate during the install, you’ll need to activate it when you first run any of the Office 2010 apps.   Conclusion The Tech Guarantee makes it easy to get the latest version of Office if you recently purchased Office 2007.  The Tech Guarantee program is open through the end of September, so make sure to grab your upgrade during this time.  Actually, if you find a great deal on Office 2007 from a major retailer between now and then, you could also take advantage of this program to get Office 2010 cheaper. And if you need help getting started with Office 2010, check out our articles that can help you get situated in your new version of Office! Link Activate and Download Your free Office 2010 Tech Guarantee Upgrade Similar Articles Productive Geek Tips Remove Office 2010 Beta and Reinstall Office 2007Upgrade Office 2003 to 2010 on XP or Run them Side by SideCenter Pictures and Other Objects in Office 2007 & 2010Change the Default Color Scheme in Office 2010Show Two Time Zones in Your Outlook 2007 Calendar TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Windows Media Player Plus! – Cool WMP Enhancer Get Your Team’s World Cup Schedule In Google Calendar Backup Drivers With Driver Magician TubeSort: YouTube Playlist Organizer XPS file format & XPS Viewer Explained Microsoft Office Web Apps Guide

  Read the article

• Spell checker 2.3 for Visual Studio 2008 SP1

  - by Latest Microsoft Blogs

  Minor update for the Spell checker add-in for VS 2008 SP1. It is now available at Visual Studio Gallery . Direct link: http://visualstudiogallery.msdn.microsoft.com/en-us/2f3d691d-8838-4d84-ad64-44a02db37e30 What's new in version 2.3: Updated native Read More......(read more)

  Read the article

< Previous Page | 502 503 504 505 506 507 508 509 510 511 512 513  | Next Page >