Search Results

Search found 11880 results on 476 pages for 'high traffic'.

Page 51/476 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

  • High shmmax value in Redhat 6.3

    - by xpapad
    We are using Redhat 6.3 with 30G RAM to host our Postgres server. The (default) shmmax value is 68,719,476,736 In some forums I have read that having an shmmax value larger than the RAM causes extensive paging, but in the Redhat forums it warns against changing a kernel parameter that is already configured to a value larger than the minimum requirements for an environment. In ServerFault I've read that this probably has no impact. So is there any impact of having shmmax value RAM in a DB server, or the kernel understands this and handles it appropriately? Thanks

    Read the article

  • Using VLC to Unicast High Definition Webcam over local gigabit LAN with low/zero delay

    - by Robin Day
    We're setting up a webcam "window" between two offices in the same buildilng. The two PC's are connected to the same gigabit switch. We're using VLC to stream the webcam over HTTP using the following commands. vlc dshow:// :dshow-caching="0" :dshow-size="640x480" :sout=#transcode{vcodec=h264,vb=0,scale=0}:http{mux=ffmpeg{mux=flv},dst=:8080/} :no-sout-rtp-sap :no-sout-standard-sap :ttl=1 :sout-keep vlc http://192.168.0.1:8080 :http-caching="0" Even with the caching set to zero, the delay in the image is a good 2-3 seconds. The CPU usage of each pc is also maxed. I'm guessing it's the transcoding that's causing much of the delay. Can anyone give me some changes to these command lines that will reduce the transcoding power, or send the webcam over a different protocol, or anything that will reduce the delay of the cameras? Bandwidth is not an issue at all as the pc's can be connected to a dedicated switch/vlan if required.

    Read the article

  • High-performance Academic Server [closed]

    - by PHPsmith
    Suppose I want to build a server for the university's academic interests. The server is dedicated only to a site, where users (students and lecturers) just view and fill the academic data. But at a time (e.g. once a semester), about 12,000 students will access the site simultaneously. Due to limitation of resources, I have to build the server using free software (except for the operating system Windows 7, the university has been prepared). The hardware is also limited to the usual 4-core computers (eg, Ivy Bridge Intel Core i7-3770) with approximately 16GB of memory (DDR3 1600 MHz), equipped with an RJ-45 port (Intel 82 579 Gigabit Ethernet). With all these limitations, I have to choose the software (web server, database, etc) are appropriate for this purpose is achieved. I decided to create a site in PHP. Please help me by answering the following questions based on your expertise. (my prime candidate software to consider after googling) Web server which is faster & stable & secure, when implemented and optimized for PHP? And why? (nginx) PHP accelerator which is faster & stable & compatible with the selected web server? And why? (APC with Zend Optimizer+) Database which is faster & stable & secure, when implemented and optimized for selected web server and selected PHP accelerator? (MySQL) Are there any errors that have been or will be happening from my condition is? If there is, please enlighten me? Is there anything else I need to know in order to achieve this goal? If there is, please enlighten me? I understand that the performance also depends on the implementation of source-code program, so I assume it will create a site with the best efficiency (e.g. using AJAX).

    Read the article

  • How to direct outgoing traffic through specific interface?

    - by user1434058
    I added eth1 and eth2 to my Ubuntu Server, all 3 use DHCP and are on the same lan eth0 10.0.0.41 eth1 10.0.0.42 eth3 10.0.0.43 Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default router.net 0.0.0.0 UG 100 0 0 eth0 10.0.0.0 * 255.255.255.0 U 0 0 0 eth0 10.0.0.0 * 255.255.255.0 U 0 0 0 eth1 10.0.0.0 * 255.255.255.0 U 0 0 0 eth2 curl --interface eth1 www.google.com doesn't work what else do i need to do for the above to work?

    Read the article

  • High resolution on small screen

    - by Andrew Cetinick
    I just purchased a new ultrabook (Asus UX32VD). Awesome laptop, but I am having trouble using it with its native resolution being 1920 x 1080. Text is so small and hard to read. I have increased the text size in the display options but it don't really improve it for all scenarios, especially in webpages. I am wondering if there is a possible solution to this? Simply lowering the resolution makes everything look pixelated.

    Read the article

  • System Lags/Freezes when under high usgage

    - by tom
    I am not sure if its my GPU / Memory or Hard drive thats failing. For example if I'm runnning more than one instance of chrome and running an application that takes up a lot of resources, my system will start to lag and freeze. When I launch Photoshop the GPU feature disables automatically, this also lags when I click on menus and when working on documents in Photoshop. I really dont know where to start, if i should buy a new graphics card or test the memory or could it be my OS drive? System: Windows 7 64bit, ATI Raedeon 5850, Corsair 2x4GB http://i.stack.imgur.com/qqkLZ.jpg

    Read the article

  • Windows 7 with two network cards doesn't route traffic

    - by Tomek
    I have simple task to do: I have wni7 with two nics.I want to connect another comp(osx) to win7 through second nic to connect it to internet. I already changed the registry. Win7 interface with 192.168.2.1 has no gateway set (no point to do that) OSX interface with 192.168.2.2 has gateway set to 192.168.2.1 I do not add any routes on win7, every thing seems to be already there network on second nic is detected as "undefined network" (probably effect of no gateway) i can achieve any connectivity to internet from OSX only by enabling network connection sharing on nic with 192.168.2.1, but it enables NAT and I'm interested only in pure routing without nat(it's a setup for some research). firewall is off. It seems to me that win7 refuses to forward packets for some reason. Perhaps "undefined network" and NLA service is to blame, although i couldn't find any info about that. Below ascii schematics of my setup: internet<--router(192.168.1.1)<--(192.168.1.1) WIN7 (192.168.2.1)<--(192.168.2.2)OSX Thanks

    Read the article

  • Multi domain server with dedicated SSL's HA

    - by user3692800
    I am hosting a server with 150 domain names (websites), each of the ssl's requere dedicated IP address. So server windows 2008, with 150 IP addressees and 150 websites. I need to have high availability solution. So thinking setting up AWS but ELB will not be a solution... and max IP's I can get per instance is 12 addresses. So what can I do to have all 150 sites hosted on one instance and be HA with instance in different availability zone.

    Read the article

  • ADSL2+ - High sync-rate, good line attenuation, but low noise margin and slow speeds

    - by Mark Pim
    I've been with my ISP (IdNet) for a few months and have been getting some good speeds, but in the last week the speed has dramatically decreased (from 15 Mbps+ to around 0.2 Mbps). This happens at all times of day, not just peak periods. Obviously I've done all I can to isolate problems my end - only one PC is connected to the router (via ethernet cable) and no other background programs are using the network etc. I've raised the issue with the ISP and they've suggested trying a new ADSL filter to see if that is casuing the problem, but I thought it would also be good to get the opinion of superuser on possible causes or other troubleshooting I can do. Here are the juicy stats :) My router (Netgear DGN1000) reports: Downstream Upstream Connection Speed 17602 kbps 1062 kbps Line Attenuation 17.9 db 8.6 db Noise Margin 6.0 db 6.1 db I used RouterStats and it seems to show those figures stay fairly consistent all the time I ran the BT speedtest and it reported: download speed of 164 kbps, out of a max achievable of 21000 kbps upload speed of 859 kbps, out of 1048 kbps DSL connection rate 17719 kbps down and 1048 kbps up IP Profile of 15000 kbps Is there any more troubleshooting I can do? Does this look like a problem with my equipment / wiring or with BT's line? Any advice would be great :)

    Read the article

  • Windows server response time very high

    - by Nagaraju Bandla
    Server Specs Windows Server 2008 R2 64 bit Provider : Fasthosts .Net Framework: 4.0 6 GB RAM (its using 4.6 GB) i have a website with thousands of pages structured like folderone/1/one to 500.aspx folderone/2/one to 500.aspx . . folderone/500/one to 500.aspx To load this pages for the first time after the release, for each folder it takes about 20 to 30 minutes and once one page is loaded the rest of the pages loads fine. This happens for all folders. And this repeats every time i restart the server, when a added anything to app_code or if i change the web.config. My site is mainly works Google and due to this problem its giving errors. Any help will be highly appreciated please. i am happy to buy a beer for you if its resolved. Thanks in advance...

    Read the article

  • Super simple high performance http server

    - by masylum
    I´m building a url shortener web application and I would like to know the best architecture to do it in order to provide a fast and reliable service. I would like to have two separate servicies in different machines. The first machine will have the application itself with a apache, nginx, whatever.. The second one will contain the database. The third one will be the one that will be responsible to handle the short url petitions. For the third machine I just need to accept one kind of http petition (GET www.domain.com/shorturl), but it have to do it really fast and it should be stable enough. Which server do you recommend me? Thank's in advance and sorry for my english

    Read the article

  • apache high system CPU time

    - by jperelli
    I have a web server: ubuntu apache+php app+postgresql and a stats server: ubuntu apache+php - piwik and munin2 installed. The communication for munin2 is made through ssh. In munin i see a lot of system cpu activity, that I assume it it because of apache (i see 5 or 6 apache instances using ~5% CPU on top) I was not having this system CPU activity before. Does anyone knows how can I see where that comes from? EDIT: some munin graphs

    Read the article

  • High Steal Time utilization on Apache Linux Server

    - by JMC
    I have a CentOS "development / testing" server that runs extremely slowly. It's running Apache and Mysql using PHP. Top reports that 98% of the CPU utilization is frequently spent on "st" - Steal Time. What could cause a server to spend so much CPU on steal time, and how can I diagnose the problem? I didn't notice the problem until after I granted a third party developer root access (for all I know it has a root kit running, though unlikely).

    Read the article

  • AT&T Filtering FTP traffic?

    - by xpda
    Using an AT&T DSL, I cannot ftp upload or ftp download a few files of a large 1500 set. The problem is the file name. I can change a few characters of the file name, and they upload fine. I can change the file names from upper to lower case and they upload fine. If I change back to the original file name, it will not upload again. When it doesn't upload, it starts, transfers about 5% of a 5-10 meg file, and then times out. I have uploaded one of the files under a different name, changed the name back to the original, and it will not download via ftp. It will download onto a browser, and it will ftp download just fine with a different name. It just will not download with ftp. I have reproduced this uploading to three different servers on 1and1 and Amazon EC2. When I try it on a non-AT&T ISP client, it works OK. Here is a file that did not upload until I had renamed it. (I have changed it back to the original name): "http://xpda.com/nautnew/11302 STOVER POINT TO PORT BROWNSVILLE SIDE A.png" This problem is unrelated to connection, speed, and file content. Only things I can see that makes a difference are the file name and ATT DSL. Does ATT have some kind of ftp file filtering? Is there anything else that could cause this behavior?

    Read the article

  • Cherokee high virtual memory usage even after disabling I/O Cache

    - by nidheeshdas
    I've Ubuntu 10.04LTS 64-bit running on a openvz container and Cherokee 1.0.8 compiled from source. The virtual memory usage of cherokee-worker is around 430 MB even after disabling I/O cache from Advanced - I/O Cache - NOT enabled. Is this issue particular to openvz? Because many people reported to have successfully reduced virt memory usage by disabling io cache. htop output: http://imgur.com/z5JEL.jpg (newbies not allowed to post image.) thanks in advance. nidheeshdas

    Read the article

  • How to setup a simple Ubuntu Server Tomcat cluster on VirtualBox for testing?

    - by Alex Pakka
    I am looking for a step by step instructions to setup at leat two (and later more) simple Ubuntu Virtual Core 12.10 Server VMs on Oracle VirtualBox under Windows 7 64bit. The test setup would be: Apache HTTP server on the Windows host acting as a Load Balancer. The result will be that going to http://localhost:8080 would balance between two nodes and prove session replication. Two lean, small footprint Ubuntu Server guest nodes with Java 7 and Tomcat 7. The intention is to help everyone doing High Availability / Load Balancing development and testing to create a reasonable environment on the local workstation or mainstream notebook in as little time as possible.

    Read the article

  • MySQL : table organisation for very large sets with high update frequency

    - by Remiz
    I'm facing a dilemma in the choice of my MySQL schema application. So before I start here is a picture extremely simplified of my database : Schema here : http://i43.tinypic.com/2wp5lxz.png In one sentence : for each customer, the application harvest text data and attached tags to each data collected. As approximation of the usage of each table, here is what I expect : customer : ~5000, shouldn't grow fast data : 5 millions per customer, could double or triple for big customers. tag : ~1000, quite fixed size data_tag : hundred of millions per customer easily. Each data can be tagged a lot. The harvesting process is permanent, that means that around every 15 minutes new data come and are tagged, that require a very constant index refreshing. A lot of my queries are a SELECT COUNT of DATA between specific DATES and tagged with a specific TAG on a specific CUSTOMER (very rarely it will involve several customers). Here is the situation, you can imagine with this kind of volume of data I'm facing a challenge in term of data organization and indexing. Again, it's a very minimalistic and simplified version of my structure. My question is, is it better: to stick with this model and to manage crazy index optimization ? (which involves potentially having billions of rows in the data_tag table) change the schema and use one data table and one data_tag table per customer ? (which involves having 5000 tables on my database) I'm running all of this on a MySQL 5.0 dedicated server (quad-core, 8Go of ram) replicated. I only use InnoDB, I also have another server that run Sphinx. So knowing all of this, I can't wait to hear your opinion about this. Thanks.

    Read the article

  • How to manage SOAP requests to a pool of VM each listening on a HTTP port with a priority value in these requests?

    - by sputnick
    I have a front SOAP web-server under Linux. It will have to communicate with Windows Servers VM listening each on a HTTP port, for a HTTP POST request. The chosen VM should return a report of the task to the SOAP client. In the SOAP requests, there's a special variable : the priority of the request (kind of SLA), and my question is coming right now : I think of using a ha software (nginx, HAProxy, HeartBeat...) that can manage priority in this point of view. Is it relevant or do you think I need to implement a queue by myself with some specific developments? Ex: I have a SOAP requests with low priority in the pipe : the weight priority for these VM should be decreased if I have high priority SOAP requests at the same time. Any clue will be really appreciated.

    Read the article

  • Up-to-date Comparison of High-Speed USB Flash Drives

    - by Zoredache
    I am looking for comparison of the performance of USB flash drives. I have found several older comparisons, but I am trying to find a more up-to-date comparisons that apply to the larger storage sizes (32-128GB). I can try looking up the specs of various drives, but vendors have been known to exaggerate, or use numbers that are on accurate in tests that do not reflect actual usage. I was hoping to find 3rd party site which had perform testing.

    Read the article

  • High-End Gaming Desktop PC in France [closed]

    - by Lerikunus
    Hello, I was looking to buy an ALIENWARE AREA 51, as my Desktop crashed some days ago. But the Preliminary Ship date is 03.01.11 and I need the new PC until Friday next week =( Does someone know a(n) (online)-store where Build&Shipping time is quite low so I can get it until next Friday? I am living in France (Nice). Or any place I can ask fot his kind of advice? This is my desired configuration: Overclocked Intel® Core™ i7 980x Extreme Six Core Processor (4.0GHz, 12MB Cache) 12GB Triple Channel 1600MHz DDR3 Dual 2GB ATI Radeon™ HD 6950 2TB RAID 1+0 (4x 1TB SATA-II, 7,200 RPM, 32MB Cache HDDs) 2TB RAID 1 (2x2TB SATA-II, 7,200 RPM, 32MB Cache HDDs) Thank you very much!

    Read the article

  • 2 Nics - Same Subnet..Route backup traffic through one of them

    - by Matthewhall58
    I have a windows server and a centos linux server. I want the nightly backup file (targz) that copies to the windows machine to use a different nic so that the main nic is not burdenend with moving the large file. Each server has 2 Nics in it. the network is 10.173.10.0 mask 255.255.255.192 Centos Linux Box: Eth0 is configured with 10.173.10.80 mask 255.255.255.192 gw 10.173.10.65 Eth 1 is configured with 10.173.10.71 mask 255.255.255.192 gw 10.173.10.65 Windows Box Eth 0 is 10.173.10.72 mask 255.255.255.192 gw 10.173.10.65 Eth 1 is 10.173.10.70 mask 255.255.255.192 gw 10.173.10.65 I can ping each machine from each machine. On the linux machine I use the command route add -host 10.173.10.70 dev eth1 but then when i ping 10.173.10.70 it is unreachable..... WHY?

    Read the article

  • Windows 2008 R2 on ESXi 4.1 cpu utilization kernel high

    - by MK.
    I have a Win2k8 guest running on ESXi 4.1. The host has 12 cores and the problem happens even if the guest is the only VM on the host. We have 4 cores dedicated to the guest. We noticed that network starts chocking when the CPU load goes up. After some testing we noticed that when running a simple CPU hogging tool set up to run 3 threads at 100% the regular CPU load goes to 75% like it should and the "kernel times" graph in task manager goes up to 25%. My intuition tells me that the network problem and kernel times problem are the same. This is confirmed by another similar VM we created on the same host which doesn't have either of the problems. VMWare tools are obviously installed. The nic is e1000. What else can we do to troubleshoot this?

    Read the article

  • Redirecting HTTP traffic from a local server on the web

    - by MrJackV
    Here is the situation: I have a webserver (let's call it C1) that is running an apache/php server and it is port forwarded so that I can access it anywhere. However there is another computer within the webserver LAN that has a apache server too (let's call it C2). I cannot change the port forwarding nor I can change the apache server (a.k.a. install custom modules). My question is: is there a way to access C2 within a directory of C1? (e.g. going to www.website.org/random_dir will allow me to browse the root of C2 apache server.) I am trying to change as little as possible of the config/other (e.g. activating modules etc.) Is there a possible solution? Thanks in advance.

    Read the article

  • Redirecting traffic to a https site

    - by Saif
    In our mail server there are multiple virtual email domain hosted. User can use webmail.example.com (this is the first apache virtualhost) to check mail or they can use mail.THEIR-DOMAIN.com. If the put mail.THEIR-DOMAIN.com apache shows the webmail.example.com as it is the first virtualhost and mail.THEIR-DOMAIN.com doesn't exist. Recently we imposed https for webmail.example.com and added this mod_rewrite rule: RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (.*) https://%{HTTP_HOST}%{REQUEST_URI} But now users not getting the default webmail page as they were getting before. How can we redirect all request coming to the URL "mail.ANY-DOMAIN.com" to "https://webmail.example.com"? I've tried the following but it didn't work: RewriteEngine On RewriteCond %{HTTPS} off RewriteRule (mail.*) https://webmail.example.com Thanks for your help in advance.

    Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >