Search Results

Search found 11180 results on 448 pages for 'serial port'.

Page 51/448 | < Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >

• how to forward IP request to a specific port

  - by Jeremy Talus

  I have 2 servers the first (SRV01) is running Bind and other web app the second (SRV02) is running 2 server Minecraft (^^) in Bind I have 2 A recording for the 2 server MC s1.domain.tld A SRV02IP s2.domain.tld A SRV02IP the 2 MC serv are running on 2 different port 25565 and 25566 so I want that the request from s1.domain.tld:25565 are going to SRV02IP:25565 and the request from s2.domain.tld:25565 are going to SRV02IP:25566 I think I need do this in the SRV02 iptables. I have looking some topic about iptables but nothing pertinent to me. could you help me ? rgds.

  Read the article

• Windows Server 2008 constantly spamming external IP's on outbound TCP port 445

  - by RSXAdmin

  Hi Server Fault, I have a Windows Server 2008 box running as a Domain Controller. I have noticed in my Cisco ASA firewall logs that this box is continuously sending out (like a thousand requests a second) requests on TCP port 445 to external hosts. I have made an effort to deny this outbound traffic from getting on the internet (using the ASA), however I would like these requests to stop from even occurring at all. I have tried disabling TCP/IP over NetBIOS. I have even turned on Windows Advanced Firewall on the box itself to block outbound 445 but the ASA still detects this particular traffic hitting it. I have other DC's and similar type boxes which are not behaving the same way as this box. Is this normal? Is there a way to stop this spamming? Have I been infected? Thank you universe.

  Read the article

• port forwarding using 3 static ip addresses

  - by Danny

  I am new to configuring routers. We have purchased a RV016 Cisco business router that has multiwan capability. What we are attempting to do is take map services from 3 different servers and assign 3 different static IP addresses and then forward port 80 through the router. A short term solution to building a proxy server. Is this possible? Right now we have a consumer grade Cisco router and assign a static IP and it works, we attempted the same settings on the business router and cannot get to the internet. We set it DHCP and it works fine, however we want to to forward the static ports not use DHCP.

  Read the article

• Blocking IP address with port forwarding

  - by Jeff Storey

  I have a website setup behind a router, so the router has the external facing address and it will forward requests to the webserver inside the network. If there are X number of invalid login attempts, that IP address will be blocked from logging in. The problem is that because the site is being accessed through port forwarding, all requests show up as though they are coming from the router address, and thus the router address becomes the blocked IP. I'm not sure if this is a limitation of the router (linksys wrt160n) or if this a more general issue. Is there a way to handle this?

  Read the article

• Proxy the traffic in http and https from my iPhone/iPad to VirtualBox on my Mac

  - by Nicolas BADIA

  I've got a mac running a Debian VirtualBox which forward the traffic from 8080 on the mac to 80 in the box and from 8443 to 443. The domains with the extension .dev are redirected on the mac to 127.0.0.1 with dnsmasq. The traffic on IP 127.0.0.1 is forwarded from 80 to 8080 and from 443 to 8443 using ipfw. So with this settings, my Debian VirtualBox gets all the traffic of my .dev domains in http or https. What I want is to be able to proxy the traffic of my .dev domains in http and https from my iPad to my Debian VirtualBox on the mac. I've try to setup an HTTP proxy on the ipad but I can only do it for one port (and it's not working with the port 443). Any idea on how I could achieve that ?

  Read the article

• Network with bridge and port forwarding?

  - by rafek

  Hi! Below is my current (and planned) home network configuration. I would like to connect my non-wifi-capable desktop to my home network. The question is: HOW? What device do I need? The primary requiremen is that I need to be able to forward ports to my desktop. How would I achieve this? Is there something like "double port forwarding"? Could anyone please explain this configuration to me? Thank you in advance!

  Read the article

• Windows 2008 - Define IP Order by port or service

  - by Josh

  I have a Windows 2008 server that has three IP bound to the NIC. I can select which IP Windows SMTP listens to, but I want to also set the IP address used when mail is sent. Where would I set which outbound IP to use when sending email? Without using real IPs, here is an example what I have setup. Three IPs associated with the server: 10.0.0.1 10.0.0.2 10.0.0.3 I setup the binding on 10.0.0.2 for port 25 in the SMTP server settings, so that it is the only IP that will respond for inbound. When I look at the email header from an email sent from that server, it lists the server with an address of 10.0.0.3. I would like it to use 10.0.0.2 so that when reverse DNS is performed, it maps back correctly.

  Read the article

• nginx proxy pass redirects ignore port

  - by Paul

  So I'm setting up a virtual path when pointing at a node.js app in my nginx conf. the relevant section looks like so: location /app { rewrite /app/(.*) /$1 break; proxy_pass http://localhost:3000; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; } Works great, except that when my node.js app (an express app) calls a redirect. As an example, the dev box is running nginx on port 8080, and so the url's to the root of the node app looks like: http://localhost:8080/app When I call a redirect to '/app' from node, the actual redirect goes to: http://localhost/app

  Read the article

• postfix cannot send email

  - by AKLP

  I'd like to mention that im really new to this so please bear with me. I'm trying to setup a forum software to send emails via postfix but I think my server has the port 25 blocked. I tried running these: works: ping alt2.gmail-smtp-in.l.google.com don't work: telnet alt2.gmail-smtp-in.l.google.com 25 telnet 66.249.93.114 25 tried flushing iptables and then using these rules but didn't work either: sudo iptables --flush sudo iptables -P INPUT ACCEPT sudo iptables -P OUTPUT ACCEPT sudo iptables -P FORWARD ACCEPT sudo iptables -F sudo iptables -X doing a telnet on 25 port to localhost url works but nothing when telnet'ing in none local urls. mail.log: Oct 17 01:20:24 webhost postfix/smtp[3642]: connect to alt2.gmail-smtp-in.l.google.com[2607:f8b0:400e:c03::1a]:25: Connection timed out Oct 17 01:20:24 webhost postfix/smtp[3643]: connect to alt2.gmail-smtp-in.l.google.com[2607:f8b0:400e:c03::1a]:25: Connection timed out Oct 17 01:20:24 webhost postfix/smtp[3642]: 4744380032: to=<[email protected]>, relay=none, delay=2892, delays=2741/0.03/150/0, dsn=4.4.1, status=deferred (connect to alt2.gmail-smtp-in.l.google.com[2607:f$

  Read the article

• Windows 7 is blocking ports

  - by Caleb1994

  I am trying to open port 80 and 3690 for HTTP and svnserve respectively. I have Windows Firewall off, and have tried temporarily disabling Mcafee VirusScan Enterprise, to no avail. According to http://www.yougetsignal.com/tools/open-ports/, both ports 80 and 3690 are still blocked. I can't think of what would be blocking them if Windows Firewall and my antivirus are disabled. Here is the output of netsh firewall show state Firewall status: ------------------------------------------------------------------- Profile = Standard Operational mode = Disable Exception mode = Enable Multicast/broadcast response mode = Enable Notification mode = Enable Group policy version = Windows Firewall Remote admin mode = Disable Ports currently open on all network interfaces: Port Protocol Version Program ------------------------------------------------------------------- 3690 TCP Any (null) 22 TCP Any (null) 80 TCP Any (null) 1900 UDP Any (null) 2869 TCP Any (null) Any help? I'm not sure what each item on the list of enabled/disabled items is, but "Operational Mode" is disabled, so I assume that one refers to me disabling Windows Firewall. I know that since Windows Firewall is off, this output might not be useful, but I figured I'd include it just in case, haha.

  Read the article

• Windows 7 is blocking ports

  - by Caleb1994

  I am trying to open port 80 and 3690 for HTTP and svnserve respectively. I have Windows Firewall off, and have tried temporarily disabling Mcafee VirusScan Enterprise, to no avail. According to http://www.yougetsignal.com/tools/open-ports/, both ports 80 and 3690 are still blocked. I can't think of what would be blocking them if Windows Firewall and my antivirus are disabled. Here is the output of netsh firewall show state Firewall status: ------------------------------------------------------------------- Profile = Standard Operational mode = Disable Exception mode = Enable Multicast/broadcast response mode = Enable Notification mode = Enable Group policy version = Windows Firewall Remote admin mode = Disable Ports currently open on all network interfaces: Port Protocol Version Program ------------------------------------------------------------------- 3690 TCP Any (null) 22 TCP Any (null) 80 TCP Any (null) 1900 UDP Any (null) 2869 TCP Any (null) Any help? I'm not sure what each item on the list of enabled/disabled items is, but "Operational Mode" is disabled, so I assume that one refers to me disabling Windows Firewall. I know that since Windows Firewall is off, this output might not be useful, but I figured I'd include it just in case, haha.

  Read the article

• 2 virtual domains: one on port 80 one on port 8080, how?

  - by Simone

  I've been struggling with this, basically what I want is this: A virtual domain to run on the 80 another virtual domain to run FROM 80 TO 8080 what I've done so far is trying different combinations with apache, but all i got is having all the virtual domains pointing to port 80 this is my conf: <VirtualHost domain1.com:80> DocumentRoot /var/www/domain1 <Directory "/var/www/domain1"> allow from all Options +Indexes </Directory> ServerName domain1.com </VirtualHost> <VirtualHost server.domain2.com:80> DocumentRoot /var/www <Directory "/var/www"> allow from all Options +Indexes </Directory> ServerName server.domain2.com ServerAlias www.server.domain2.com ProxyPass / http://server.domain2.com:8080/ </VirtualHost> suggestions? :(

  Read the article

• Exchange 2007 OWA not listening on SSL port

  - by krs1

  I have an Exchange 2007 server that went down after a power failure. It has OWA access via SSL both externally and internally. OWA is working fine from the internal notwork, however I am getting a timeout when I attempt to connect externally. I pulled up wireshark and noticed that the server actually redirects to SSL. For some reason the server is not listening on the SSL port, and this seems to be causing the timeout. I normally do only development work, but I'm stuck with this since my sysadmin took off for the week and isn't answering my phone calls. As far as I know it shouldn't be a firewall issue. Aside from me not wanting to work on the damn thing, what should I look for?

  Read the article

• blocking port 80 via iptables

  - by JoyIan Yee-Hernandez

  I'm having problems with iptables. I am trying to block port 80 from the outside, basically plan is we just need to Tunnel via SSH then we can get on the GUI etc. on a server I have this in my rule: Chain OUTPUT (policy ACCEPT 28145 packets, 14M bytes) pkts bytes target prot opt in out source destination 0 0 DROP tcp -- * eth1 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW,ESTABLISHED And Chain INPUT (policy DROP 41 packets, 6041 bytes) 0 0 DROP tcp -- eth1 * 0.0.0.0/0 0.0.0.0/0 tcp dpt:80 state NEW,ESTABLISHED Any guys wanna share some insights?

  Read the article

• Exchange server listening on port 25 but clients dont recieve emails

  - by Josh R

  My exchange server is listening on port 25, that is I can telnet into it and send an email but Outlook 2010/2007, OWA, and ActiveSync are not pulling down emails. Outlook 2010 specifically says Connected To Exchange Server and Updating Inbox but it never updates the inbox. Also, OWA shows some of the newer mail messages, but when I double click on one to open it up in OWA, it times out. Any idea what could be causing this? Also Exchange Transport and Information Store are started. Thanks!

  Read the article

• OS X Server: SMTP Server problem

  - by plucked

  Hi, I have problem to setup my mail server. My system is a OS X 10.6.2. Server. I configured the mail server so far, but I cannot connect to the smtp server correctly. Correctly means that I can connect via telnet (and do the "HELO") from another server within the same serverrack, but not from outside. But when I try to telnet my http server, it works fine from outside. I already checked my firewall rules with "sudo ipfw list" and the port 25 is not blocked in any case. What could be the problem with connecting to port 25 via telnet from outside of the serverrack? Cheers

  Read the article

• iptables redirect single website traffic to port 8080

  - by Luke John Southard

  My goal is to be able to make a connection to one, and only one, website through a proxy. Everything else should be dropped. I have been able to do this successfully without a proxy with this code: ./iptables -I INPUT 1 -i lo -j ACCEPT ./iptabels -A OUTPUT -p udp --dport 53 -j ACCEPT ./iptables -A OUTPUT -p tcp -d www.website.com --dport 80 -j ACCEPT ./iptables -A INPUT -m conntrack --cstate ESTABLISHED,RELATED -j ACCEPT ./iptables -P INPUT DROP ./iptables -P OUTPUT DROP How could I do the same thing except redirect the traffic to port 8080 somewhere? I've been trying to redirect in the PREROUTING chain in the nat table. I'm unsure if this is the proper place to do that tho. Thanks for your help!

  Read the article

• How do I set up my home server to go directly to a port other than 80

  - by Kevin

  I'm using dyndns, a lynksis wt54g router, and tomcat 7 with spring to set up a web server. This is my first time to attempt this. I'm sure this is a very common question, but I don't know enough to find the answer after quite a bit searching. Dyndns is successfully forwarding to my ip. The main problem is, the router admin login is coming up when my url is used. I'm hosting my site on port 8080. I have port forwarding set up for port 8080 but my request times out when I attempt to use my url like this www.myurl1234.com:8080. I don't want users to have to type the port anyway. I also tried changing the management port to 82 and hosting on port 80, but I still get the router admin login when I use my url. Where am I going wrong? Can I set it up so that www.myurl1234.com goes straight to port 8080?

  Read the article

• Can't access server from external IP

  - by Mathias

  I have a problem with my web server; I can't access it from the external IP address. I'm using an IIS 7 server, but I've tried with apache on Linux as well. I have forwarded all traffic on port 80 to my computer, but it just won't work. I've done port forwarding with my Minecraft server, and it did work, but when I try it with a web server, no. I've been looking on many many forums, but their methods don't work for me. My router is a Speedport W 723V, if anyone knows that one. Any help is appreciated.

  Read the article

• Someone used my postfix smtp (port 25) to send spam mails to me

  - by Andreas

  This week, someone started to send spam-mails through my postfix-smtp access (I verified by logging in through telnet from an arbitrary pc and sending mails with any ids myself) on my server, with recipient and target being [email protected]. Since I have a catchall and mail-fowarding to my google account, I received all those (many) mails. After a lot of configuration (I lost track of what change did what, going through dozends of topics here and over the net) that hole seems fixed. Still, what hapened? Does port 25 need to be open and accepting for my catchall to work? What configuration did I do wrong? I remember the first thing I changed (that had an effect) was the inet_interface setting in main.cf, only later to find out that if this does not say "all", my mail to mydomain.com does not get forwarded any more.

  Read the article

• Cannot send email from EC2 instance on port 587

  - by Tahsin Mostafiz

  I have written a mail service for our flask application that uses Celery and RabbitMQ to send emails (using gmail). I have got the celery consumer and producer communicating okay but I cannot get to send send emails. I am getting a socket.error: [Errno 101] Network is unreachable. I think this means that AWS is blocking port 587 - even though in my security group I opened both ports 587 and 25 (inbound and outbound). Any reason why this is happening? Any help will be highly appreciated.

  Read the article

• Multi-site Drupal install with sites on different ports using Apache ip-based hosting?

  - by MattB

  In the past we've used name-based virtual hosting in Apache. We recently converted websites to SSL and had to go the ip-based route. As a result, we currently have an instance that is set up as follows: www.domain.com using port 80 dev.domain.com using port 8080 Both use the same IP. Is this scenario possible using Drupal multi-site functionality? While we find that dev.domain.com works and reads the correct "dev" database (using the dev settings), it reads theme files from the "www" site instead which is not what we want. Is the culprit the dev's htaccess file? Apache is listening on 8080 and does use the proper DB settings, but just not the correct theme files. One other note: browsing dev.domain.com:8080 gives an error: "The page isn't redirecting properly". Should we just purchase a new IP address for the dev website, or would this still not help? Any advice would be appreciated. Thanks.

  Read the article

• Ubuntu + SSL ports + AVAST

  - by jurajvt

  I have an interesting problem with communication via standard SSL ports. Fresh installed Ubuntu 14.04 server + Postfix + Dovecot, SASL authentication provided by Dovecot, self-signed certificate generated trough the Dovecot script mkcert.sh. Redirected ports on ZyWALL USG 200. I can send and receive e-mails from outside with standard ports 25 and 110, but not over 587. I am connecting to my server from machine with Windows 8.1 + VMWare Player + Ubuntu 14.04 Desktop + ssh. On Windows host I have installed Avast! antivirus. When I am trying to telnet from virtual machine to server over 587, it refused connection. But when I turn on Avast! it let me in to message Connected to... Same with nmap. When Avast! is turned on it is show me all SSL ports. When I turned it off, only standard ports appeared. OpenSSL shows me CONNECTED(00000003). But outside virtual machine directly in Windows 8.1 using nmap with zenmap there are not opened SSL ports in both Avast! states. From other external linux machines are problems with touching SSL ports same - refused. I have turned on submission in master.cf and 587 port is correctly listening on 0.0.0.0 in process master.pid which belongs to Postfix. I can telnet, or nmap over port 587 to my domain directly from server. Other ports like 995, 993 are OK on localhost, too. It is true, that I can't send emails via 587 anyway (Avast! turned on/off), but I can see ports opened. It is possible, that I have simply bad certificate and Avast! has right one, so with turned it on I can see opened ports? EDIT: To be more clear, I can't see or using port 587 everywhere from outside (tried Thunderbird, telnet, openssl, nmap, putty, swaks; both from Linux or Windows machines) and that is my problem. It was only by chance that I saw opened ports when Avast! is turned on.

  Read the article

• Centos 6.2, Apache 2 and Listen port for socket connection

  - by salvosav

  I'm trying to make a socket connection between a client and my server through a php script. To do this, I opened a port on iptables, and configure a virtual host with apache to redirect all traffic from my door to the folder that contains the file index.php, which is my script. Doing some tests the door is open, but using command netstat -ltn , I see ':::35100'. Looking on the net I understand if in this way is only listen inward and not outward. But I don't understand how can I turn this ':::35100 '-' in this '0.0.0.0:35100 '. Or, better yet, how to add this rule. Any ideas? thanks

  Read the article

• USB port not working

  - by sharza

  Everytime I put pendrive in the USB port(all ports in my computer) it doesnt work especially when plug the USB Flash Drive, but after several hours it work again. But When I try to open this pen drive data on other computers, I'm able to open & work ... So definitely there is no problem with my pen drive. and I've enabled USB keyboard & mouse in Bios. I using windows xp and using USB 2.0 Please help ...

  Read the article

< Previous Page | 47 48 49 50 51 52 53 54 55 56 57 58  | Next Page >