Search Results

Search found 30311 results on 1213 pages for 'dont ask ubun'.

Page 512/1213 | < Previous Page | 508 509 510 511 512 513 514 515 516 517 518 519  | Next Page >

• Copy to USB memory stick really slow?

  - by Eloff

  When I copy files to the USB device, it takes much longer than in windows (same usb device, same port) it's faster than USB 1.0 speeds (1MB/s) but much slower than USB 2.0 speeds (12MB/s). To copy 1.8GB takes me over 10 minutes (it should be < 3 min.) I have two identical SanDisk Cruzer 8GB sticks, and I have the same problem with both. I have a super talent 32GB USB SSD in the neighboring port and it works at expected speeds. The problem I seem to see in the GUI is that the progress bar goes to 90% almost instantly, completes to 100% a little slower and then hangs there for 10 minutes. Interrupting the copy at this point seems to result in corruption at the tail end of the file. If I wait for it to complete the copy is successful. Any ideas? dmesg output below: [64059.432309] usb 2-1.2: new high-speed USB device number 5 using ehci_hcd [64059.526419] scsi8 : usb-storage 2-1.2:1.0 [64060.529071] scsi 8:0:0:0: Direct-Access SanDisk Cruzer 1.14 PQ: 0 ANSI: 2 [64060.530834] sd 8:0:0:0: Attached scsi generic sg4 type 0 [64060.531925] sd 8:0:0:0: [sdd] 15633408 512-byte logical blocks: (8.00 GB/7.45 GiB) [64060.533419] sd 8:0:0:0: [sdd] Write Protect is off [64060.533428] sd 8:0:0:0: [sdd] Mode Sense: 03 00 00 00 [64060.534319] sd 8:0:0:0: [sdd] No Caching mode page present [64060.534327] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.537988] sd 8:0:0:0: [sdd] No Caching mode page present [64060.537995] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.541290] sdd: sdd1 [64060.544617] sd 8:0:0:0: [sdd] No Caching mode page present [64060.544619] sd 8:0:0:0: [sdd] Assuming drive cache: write through [64060.544621] sd 8:0:0:0: [sdd] Attached SCSI removable disk

  Read the article

• Bricscad V12 on ubuntu 11.10!

  - by gabriel

  i tried to install bricscad from the deb file but is for 32bit systems.So i had problems and i downloaded the .tgz file and ran tar -xvf and i was in the directory /opt/bricsys/bricscad/v12 So i managed to run bricscad with the command sudo sh bricscad.sh in the directory this.So my question is, do you have any idea of how to make a launcher or smthing so i can run the program from an easier way?I cannot find it in dash(unity) or in the desktop. Any help will be great! Thanks

  Read the article

• Do logins by the gdm (or lightdm) user in auth.log mean my system is breached?

  - by Pramanshu

  Please look at this auth.log (from Ubuntu 14.04) I have provided and tell me who this gdm user is and why there are all these unauthenticated logins? I am freaked out; please help! Here's the /var/log/auth.log file: http://paste.ubuntu.com/8120231/ Update: I know now that "gdm" is gnome desktop manager and it's there because of root. But please look at the log there is more and tell me if my system is breached.

  Read the article

• Shutdown, Restart, Halt issues, not powering off system

  - by Jalomba

  Before any one says search around, I have, to no avail. I can't seem to get it working after trying every fix out there. So basically, when I turn off my laptop it shuts down fine but the last line is "System will now halt" but power never gets cut, I've tried shutdown -P and shutdown -h same result. Then when I try restart it goes through the same process but hangs on "System will now restart" But I can't figure it out, I am running full Ubuntu with no other Operating Systems. Any tips?

  Read the article

• Why can't get past the user info screen when installing 10.10?

  - by Faceless

  I have a Dell Inspiron 1318 (07-08?) with an Intel Cored 2 Duo Processor and 3 GB of RAM. I can run Ubuntu 10.10 from the disk, but I've tried to install it three times with no success. As the files are installing, the program asks me to enter my user information. I'm fine through the time zone screen, and fine through the keyboard screen. But when it asks me to set my used name and password, the "next" button stays ghosted out no matter what I enter. Eventually, the installation gets to the point where it says it's waiting for me, but no matter what I do I can't get the "next" button to click. I'm a complete newbie, and I've been stuck at the same spot three times. If anyone has any idea what's going wrong, I'd love to hear about it.

  Read the article

• How can I have a Bluetooth Keyboard Auto-Connect at Startup?

  - by Grant

  I have a bluetooth keyboard for my HTPC. I pair it with my computer via bluetooth, and it works fine. However, when I turn off the keyboard or my computer, it has to connect again (which requires me entering a passcode on the computer and keyboard) when I turn them back on. I've looked through many forums and through that I have found that I'm missing some seemingly vital bluetooth files: /etc/default/bluetooth /etc/init.d/bluetooth /etc/bluetooth/hcid.conf In the instructions that I've found online so far, I must change certain lines in any of these files. I am unable to, since they do not exist. Am I missing a dependency or something? I've also tried installing Blueman but that didn't help at all. I'm running Ubuntu 10.10 (Maverick). Original post: http://ubuntuforums.org/showthread.php?t=1643386&highlight=bluetooth

  Read the article

• I loose some directories when i upgrade from Ubuntu 11.10 to 12.04

  - by maythux

  last day i upgraded my ubunut 11.10 desktop to ubuntu 12.04. I was running a KVM virtual about 7 machines and managed by virt-manage software.... anyway when i finished upgrading i found that virt-manager is not working so i have to reconfigure it again and install some other missing packages that was deleted!!!! anyway i solve this issue...then i started to restore my virtual machines i restore 2 machines without any problems the third and fourth ones (windows) make a check disk that takes more that 6 hours but finally it works... other machines i cant find their attached hard disks i don't know what happens but i cant found that files. 1- upgrading delete files!?!! 2- Is there anyway to restore those files? thanks in advance

  Read the article

• Which torrent client has command line arguments to start/stop downloads?

  - by virpara

  first of all, I want to create shell script to start/stop downloads in torrent client. I don't need CLI but if you know how I can do that with CLI using shell script then it is okay. I use jDownloader which is GUI based application but has some command line arguments as below which I use to start/stop download. -h/--help Show this help message -a/--add-link(s) Add links -co/--add-container(s) Add containers -d/--start-download Start download -D/--stop-download Stop download -H/--hide Don't open Linkgrabber when adding Links -m/--minimize Minimize download window -f/--focus Get jD to foreground/focus -s/--show Show JAC prepared captchas -t/--train Train a JAC method -r/--reconnect Perform a Reconnect -C/--captcha <filepath or url> <method> Get code from image using JAntiCaptcha -p/--add-password(s) Add passwords -n --new-instance Force new instance if another jD is running So I can easily start/stop download as follows, jdownloader --start-download jdownloader --stop-download now I want torrent client to do that through shell script.

  Read the article

• Create option to load Ubuntu or Windows 7 at start-up

  - by AXK

  We have a new Dell Optiplex 790 desktop with Windows 7 and just installed Ubuntu 12.04 on it using a USB stick that was configured as a boot drive. We created a new partition for Ubuntu during installation using the partition editor that comes up during installation. Everything seems to have gone fine with the installation except that, unexpectedly, there is no option to boot up Ubuntu when the computer is started. We just start the computer and Windows starts up with no option to ever start Ubuntu. The only way we have gotten Ubuntu to start is by putting the USB stick used for installation back into the computer and having the computer boot from it. Then GRUB shows up and the Ubuntu OS that we installed starts up (rather than the live-CD version on the USB stick). Previous times we have installed Ubuntu, GRUB shows up when we start the computer and we can choose among the various OSes installed. Can anyone suggest what to do? We want to have the option to launch either Windows 7 or Ubuntu 12.04 when we start the computer, with the default being Windows 7. Right now there is no option and Windows 7 just starts the way it did before we installed Ubuntu. Note that if we hit F1 soon after starting the computer, we get some sort of Windows bootloader (not sure of exact name) but there is no option for Ubuntu; just Windows 7. Also note that if we hit the shift key soon after starting the computer, as some help pages have suggested, nothing happens (Windows 7 is loaded as usual). Thanks in advance!

  Read the article

• Browsing redirected and ad playing in background - Malware?

  - by Tim

  Recently i have noticed when browsing a web page will be redirected to something other than what i click on. For instance, when i tried going to www.askubuntu.com via a link on ubuntu.com it redirected me to some other site than this one. Also when on a page with no flash videos of any kind or pop up windows an ad will start playing. The only way to get it to stop is to wait for it to finish or close the browser and start over again. I have run Clam AV but it has not found anything.

  Read the article

• 12.04 server on home network

  - by dustin mantei

  I need advice to help me with a server install, I'm new to ubuntu and linux in general. I have 6 systems in my house, 5 being windows 7 and this laptop that I am typing on is Linux mint 13 Maya. Question is, my wife will not transition to anything. She is stuck in Gates-land. so, can I make a server with ubuntu 12.04 (burnt disc image last night) so that all systems in my home can access and my mother-in-law in another state can also access with a username? That would be awesome and it may convince the war dept (my wife) to change all the systems in my house to ubuntu/linux. Sorry this is so long winded, but all the questions I have seen on this forum don't answer it completely.

  Read the article

• Problem with WindowsXp on VirtualBox in 12.10

  - by umpirsky

  When I try to start it I get: Failed to open a session for the virtual machine WindowsXp. The virtual machine 'WindowsXp' has terminated unexpectedly during startup with exit code 1. Result Code: NS_ERROR_FAILURE (0x80004005) Component: Machine Interface: IMachine {5eaa9319-62fc-4b0a-843c-0cb1940f8a91} and in another dialog: Kernel driver not installed (rc=-1908) The VirtualBox Linux kernel driver (vboxdrv) is either not loaded or there is a permission problem with /dev/vboxdrv. Please reinstall the kernel module by executing '/etc/init.d/vboxdrv setup' as root. If it is available in your distribution, you should install the DKMS package first. This package keeps track of Linux kernel changes and recompiles the vboxdrv kernel module if necessary. When I try to run: $ sudo /etc/init.d/vboxdrv setup [sudo] password for umpirsky: sudo: /etc/init.d/vboxdrv: command not found Any idea?

  Read the article

• Sync calendar and contacts with Android smartphone

  - by takeshin

  I use Thunderbird with Lighting calendar addon, which stores calendar data in iCalendar format. How can I synchronize this calendar and Thunderbird contacts with Android based smartphone (HTC Wildfire). I know I can use Google Account, but I'd prefer to use bluetooth or even better, local access via wi-fi (no internet connection available). Is there any complete Ubuntu smartphone synchronization guide somewhere?

  Read the article

• Truecrypted Windows 7 missing in Grub2 after upgrade

  - by user287545

  I have an encrypted dual boot Windows 7/Ubuntu System and upgraded my Ubuntu today. Everything went smooth but my Windows is not shown in the Grub2-List anymore. Starting up I have the Truecrypt Bootloader and after entering the Password I get to Grub (now Grub2). There my Windows 7 entry is missing now. Here is my report: http://paste.ubuntu.com/7569182/ Updating Grub did nothing to it. My guess is that within Ubuntu it does not recognize my Windows Installation on sda1 anymore. I can't mount it aswell. I can only mount it via Truecrypt itself. I think I might have to manually insert the menu item for Windows into that Grub config file. I guess that after entering the password in the truecrypt bootloader it would be possible to start Windows if the item was there - just a guess though. Edit: I basically followed these steps to set up my system: Dual Booting Windows 7 with Ubuntu 12.04LTS with Truecrypt

  Read the article

• Broke my sudoers password, how do I reset it without using sudo?

  - by Eric Dand

  I thought it would be a good idea to finally take the password off my little netbook since it has never actually been of any use, and has mostly just slowed down . But when I went to change my password, there wasn't even an option to make it blank, and any attempt to make it a few easy characters was met with "Password too weak". So I did what any good geek would do and popped open the terminal, read the manual entry for passwd and quickly used the -d option to remove the password from my account. It all went well for a couple days (I even managed to also make my keychain password blank) until I tried to update the thing. My sudoers password is not blank, and it's not my old password. I have no idea what it is. How do I reset it (or even better, make it blank) without the use of the sudo command?

  Read the article

• background process outputs to the console

  - by broiyan

  Suppose test.sh is a bash script that is empty or contains only exit 0. When the script is backgrounded, what is the significance of the 1 and 16320 printed to the console? b@sam:~/Documents/bashscripts$ ./test.sh & [1] 16320 b@sam:~/Documents/bashscripts$ [1]+ Done ./test.sh b@sam:~/Documents/bashscripts$ Then if user hits ENTER at the command prompt, as illustrated above, another line appears and it shows this [1]+ Done ./test.sh What is the significance of the 1 digit and the + symbol?

  Read the article

• Double entries in the gnome 3 task bar

  - by Mark

  I am running Ubuntu 12.04 with Gnome 3. All was working well except that graphics were slow and even moving a window on the screen seemed slow. I installed the fglrx ati driver. Which seems to have improved matters. But on first login I had all gnome items duplicated. That is my task bar has the ubuntu sign, then says Applications, then places then the ubuntu sign then Aplications and then places. Any application I run produces two icons at the bottom of the screen. This was after a reboot. I rebooted again. Now I have 3!! On the right each set of icons such as printer is also trippled!! See screenshot at http://jetmark.co.uk/Screenshot.png See Dmesg at http://jetmark.co.uk/dmesg.txt Any suggestions welcome. Reboot - now I have 4!! So one set gets added on each reboot. Help!! I am going to be task barred out before long!!

  Read the article

• Logitech Microphone (AK5370) inaudible volume

  - by Iain Lane

  I bought this microphone from Amazon last week. It's detected just fine in 12.10. I can see it in the sound preferences. The problem is that the volume is so low as to be inaudible, even when turned up to maximum in this dialog. It is working, as I can see that the meter responds to noise, but it's just too low. alsamixer's control is the same, so that doesn't help. I tried messing around in pulseaudio too, but to no avail. In lsusb it's Bus 002 Device 004: ID 0556:0001 Asahi Kasei Microsystems Co., Ltd AK5370 I/F A/D Converter.

  Read the article

• Grub2 with BURG: duplicate Windows entries, how do I remove one?

  - by Tomas Lycken

  I have a dual boot system with Ubuntu 12.04 and Windows 7, using GRUB2 (with Burg) as boot loader. For some reason, the Windows installation shows up twice in the boot menu: Ubuntu GNU/Linux, with Linux 3.2.0-24-generic Ubuntu GNU/Linux, with Linux 3.2.0-24-generic (recovery mode) Windows 7 (loader) (on /dev/sda1) Windows 7 (loader) (on /dev/sda2) If I look in my partition table, /dev/sda2 is C:\ of the Windows installation, and /dev/sda1 is the "System Reserved" partition (which, IIRC, is Windows' own bootloader). Furthermore, gparted shows /dev/sda2 - but no other partitions - with a boot flag: What is going on here? I'd like to have only the entries for Ubuntu and one entry for Windows in my boot menu - how do I remove one of them?

  Read the article

• How can I instruct nautilus to pre-generate PDF thumbnails?

  - by Glutanimate

  I have a large library of PDF documents (papers, lectures, handouts) that I want to be able to quickly navigate through. For that I need thumbnails. At the same time however, I see that the ~/.thumbnails folder is piling up with thumbs I don't really need. Deleting thumbnail junk without removing the important thumbs is impossible. If I were to delete them, I'd have to go to each and every folder with important PDF documents and let the thumbnail cache regenerate. I would love to able to automate this process. Is there any way I can tell nautilus to pre-cache the thumbs for a set of given directories? Note: I did find a set of bash scripts that appear to do this for pictures and videos, but not for any other documents. Maybe someone more experienced with scripting might be able to adjust these for PDF documents or at least point me in the right direction on what I'd have to modify for this to work with PDF documents as well. Edit: Unfortunately neither of the answers provided below work. See my comments below for more information. Is there anyone who can solve this?

  Read the article

• Where does a file copy to when I scp it?

  - by user2413

  Hi forum, i have this file myfirst.txt located on a cluster of computers down the hall, i.e.: myname@login1:~> ls myfirst.txt which i want to download to the home directory: scp [email protected]:myfirst.txt . to which i get: myfirst.txt 100% 1828 1.8KB/s 00:00 now where (on my home computer) is this myfirst.txt file ? i can't find it. It's not visible when i click 'show hidden files' either. Tia,

  Read the article

• How do I install Ubuntu to a USB key?

  - by badp

  If you are hurrying to reply, System ? Administration ? StartUp Disk Creator -- no, that's not what I'm talking about. I want to try Ubuntu 11.04's Unity without touching my existing Ubuntu install. To do this, I need to install the nVidia drivers first (sigh). To do this, I need changes to persist a reboot. To do this, I need to really install Ubuntu on a USB key. How do you do that? What I tried I tried to make a USB key from Testdrive, then boot from it, then choose "Install Ubuntu." The installer refused to install to the installation media itself. I tried, from my installed copy of Ubuntu: sudo kvm /dev/sdb --cdrom .cache/testdrive/iso/ubuntu_natty-desktop-i386.iso ...but the installer didn't detect the disk properly.

  Read the article

• Wireless drivers

  - by Kencer

  The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

  Read the article

• Fuji camera "mounts" but folder not in Dolphin After Kubuntu 13.10 upgrade

  - by user207207

  Fuji camera mount reported in attached devices but not visible in Dolphin After Kubuntu 13.10 upgrade Have reinstalled the driver, and a few other suggestions, for other cameras mounts failing on previous Ubuntu upgrades. I have already spent a couple of hours trying to get my photo's off the camera, very annoying. Worked perfectly in 11.04, 11.10, 12.04, 12.10 and 13.04. dmesg | tail; lsusb; lsb_release -a [ 6181.858786] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90009400000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396236] CPUM: APIC 00 at 00000000fee00000 (mapped at ffffc90000c6a000) - ver 0x80050010, lint0=0x10700 lint1=0x00400 pc=0x00400 thmr=0x10000 [17261.396239] CPUM: APIC 03 at 00000000fee00000 (mapped at ffffc90000c72000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396241] CPUM: APIC 02 at 00000000fee00000 (mapped at ffffc90000c70000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [17261.396255] CPUM: APIC 01 at 00000000fee00000 (mapped at ffffc90000c6e000) - ver 0x80050010, lint0=0x10700 lint1=0x10400 pc=0x00400 thmr=0x10000 [32456.884907] usb 2-5: new high-speed USB device number 2 using ehci-pci [32457.654046] usb 2-5: New USB device found, idVendor=04cb, idProduct=01e8 [32457.654050] usb 2-5: New USB device strings: Mfr=0, Product=2, SerialNumber=3 [32457.654052] usb 2-5: Product: Digital Camera [32457.654053] usb 2-5: SerialNumber: 4C3230302020091117CAA59WP18548 Bus 002 Device 002: ID 04cb:01e8 Fuji Photo Film Co., Ltd Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 2013:024f PCTV Systems nanoStick T2 290e Bus 001 Device 002: ID 046d:082d Logitech, Inc. HD Pro Webcam C920 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub No LSB modules are available. Distributor ID: Ubuntu vissibleDescription: Ubuntu 13.10 Release: 13.10 Codename: saucy sudo apt-get install gvfs-bin gvfs-mount gphoto2://[usb:002,002] Error mounting location: Error initializing camera: -108: No such file or directory ...... I have reported a bug in Dolphin, which has been transferred to Solid. Further information : I ran solid-hardware list details udi = '/org/kde/solid/udev/sys/devices/pci0000:00/0000:00:04.1/usb2/2-5' parent = '/org/kde/solid/udev' (string) vendor = '04cb' (string) product = 'Digital Camera' (string) description = 'Camera' (string) Block.major = 189 (0xbd) (int) Block.minor = 137 (0x89) (int) Block.device = '/dev/bus/usb/002/010' (string) Camera.supportedProtocols = {'ptp'} (string list) Camera.supportedDrivers = {'gphoto'} (string list) I still can't get my photo's off, I can see the folders using the Gimp menu. If anyone has got any ideas, I'm willing to try them.

  Read the article

• wkhtmltopdf displaying text as blocks

  - by making3

  We're using wkhtmltopdf in a web project (nodejs/compoundjs). We've gotten it working how we wanted on our machines (using the --use-xserver switch). However, when I try to run this on our Ubuntu server 12.04 (without the ubuntu-desktop package), the PDF cannot use the switch. When we disable the switch, the PDF displays any characters as blocks (image below). How do I resolve this without installing ubuntu-desktop and running x server? I've found liberation fonts, which installing ttf-liberation and fonts-liberation did not help. And urw-fonts, but I have yet to find an Ubuntu equivalent. EDIT: It just hit me, this doesn't matter if I'm on the server or not. On my development machine (Ubuntu 13.04 desktop), I can run the following, which produces the same blocks: wkhtmltopdf http://google.com google1.pdf While this prints out the pdf properly: wkhtmltopdf --use-xserver http://google.com google2.pdf My version of wkhtmltopdf is 0.12.0.

  Read the article

< Previous Page | 508 509 510 511 512 513 514 515 516 517 518 519  | Next Page >