Search Results

Search found 15383 results on 616 pages for 'home automation'.

Page 513/616 | < Previous Page | 509 510 511 512 513 514 515 516 517 518 519 520  | Next Page >

  • IIS6 intranet site using integrated authentication fails to load when accessed externally

    - by maik
    I've developed a couple of internal sites for my organization that use integrated authentication. Ultimately we want these sites to be accessible externally to users with domain-joined computers. The sites work as expected on domain computers while on the internal network. The problem comes when I take my laptop home and try to access those sites. IIS only has integrated authentication enabled for the two sites. When I browse to the site using IE8 I get a username/password prompt asking for domain credentials. I can put those in and it will work, but the goal is to use the cached token for integrated authentication. Next I reasoned that IE wouldn't response to an integrated auth request (is NTLM the right term for this?) unless the site was trusted. I tried adding the site to Trusted Sites but I get the same behavior as the before. I then added the site to Local Intranet sites and that is where things get weird. I get a generic error page from IE, no error code or anything. Just for funsies I loaded up Firefox (which I had previously set up to use integrated authentication) and I added this new site to network.automatic-ntlm-auth.trusted-uris. Much to my surprise I was able to load the pages up with no problem at all and saw exactly what I was expecting (including verification that the integrated authentication worked). My mind is a bit boggled at the moment as I'm not really sure where to go from here. I was hoping some of you may be able to provide some insight.

    Read the article

  • Set up WLAN in 3-level house

    - by Balint Erdi
    I'm having a hard time setting up the network in our house. It has three levels (basement, ground floor, first level). The WLAN is set up by an ASUS RT-N12 router which provides perfect coverage for the ground floor and the basement. However, I set up my "home office" in the basement where the signal barely arrived. So I purchased a TP-Link TL-WA901ND (300 Mbps) Access Point which I set up in the other corner of the ground floor to expand the ASUS router's range. I used the AP's Repeater mode for that. The distance between my computer and the TP-Link AP is 6-7 meters. There is a staircase going down from the ground floor to the basement so there are no solid walls between the computer and the AP. This setup mostly works (I am writing this from the basement) but it is not reliable (the signal strength sometimes goes down to ~40% of the max) sometimes so I wonder if I am doing it correctly or if there is a better way. Screenshot of the router's and the AP's dashboard screen follow: Any comments on what I am doing wrong or hints for improvement are appreciated. Thank you. UPDATE Tried one more thing, setting up the TP-LINK AP in Access Point mode. That way, I can make it use a different SSID. I enabled WDS/Bridge so that it expands the range of the ASUS router (see screenshot). That does not work, either, if I connect to the network set up by the TP-LINK device (PELSTER-2), I can't reach the external network (the Internet). It seems the problem always comes back to this, the TP-LINK does not have access to the external network, whatever its mode of operation.

    Read the article

  • Computer causing WiFi interference?

    - by Mannimarco
    I came back from college and brought my desktop computer. Family recently switched to Verizon FIOS and got a new router because of it. Unfortunately, my connection to the new wifi network is awful, with the download speeds (tested through speedtest.net) fluctuating wildly and often dropping below 1.5 Mbps. A laptop in the same room gets 20 Mbps. I've tried a new wireless card, thinking that mine got damaged in the move home but no luck. Here's where it gets weird: if I place the laptop near the computer, the laptop's download speeds often suffer greatly. Pulling the laptop away always fixes this. So now I'm under the impression that there's something in the computer (which I built a year ago and has had 0 issues up to this point) is causing an insane amount of wireless interference. Also bizarre: the upload speeds seem unaffected by this problem. On the laptop and desktop, upload speeds are generally around 5 Mpbs. Any ideas as to what could be causing this and how to test said theories would be fantastic.

    Read the article

  • NFS headaches with FreeBSD 4.9

    - by Ernie
    Once upon a time, this used to work, and I kept the configuration the same, but... now nothing. I'm just trying to get an NFS server set up on a FreeBSD 4.9 server. The process should be about as complicated as this: Add this entry to /etc/exports: /var/home /var/vpopmail/domains -maproot=root XXX.XX.XX.XXX Execute this: portmap nfsd -u -t -n 4 mountd -r Then this should work, regardless of network and firewall issues: showmount -e localhost But showmount -e localhost fails with the following error: RPC: Port mapper failure showmount: can't do exports rpc And even if I kill off the NFS daemon, and try a rpcinfo -p localhost, I get this error: rpcinfo: can't contact portmapper: rpcinfo: RPC: Unable to receive; errno = Connection reset by peer The portmapper is still running. Why the heck does nothing work as if it isn't? Edit to add: FYI: Sockstat gives me this: $ sockstat |egrep "(nfsd|portmap)" root nfsd 86310 3 udp4 *:2049 *:* root nfsd 86310 4 udp4 *:973 *:* root portmap 45920 0 tcp4 *:111 *:* Then, at a later time (say, 5 minutes) it's as if nfsd isn't acting as a server: $ sockstat |egrep "(nfsd|portmap)" root portmap 45920 0 tcp4 *:111 *:* But the nfs daemon is still running: $ ps ax |grep nfsd 86311 ?? I 0:00.00 nfsd: server (nfsd) 86312 ?? I 0:00.00 nfsd: server (nfsd) 86313 ?? I 0:00.00 nfsd: server (nfsd) 86314 ?? I 0:00.00 nfsd: server (nfsd)

    Read the article

  • Virtual Lan on the Cloud -- Help Confirm my understanding?

    - by marfarma
    [Note: Tried to post this over at ServerFault, but I don't have enough 'points' for more than one link. Powers that be, move this question over there.] Please give this a quick read and let me know if I'm missing something before I start trying to make this work. I'm not a systems admin professional, and I'd hate to end up banging my head into the wall if I can avoid it. Goals: Create a 'road-warrior' capable star shaped virtual LAN for consultants who spend the majority of their time on client sites, and who's firm has no physical network or servers. Enable CIFS access to a cloud-server based installation of Alfresco Allow Eventual implementation of some form of single-sign-on ( OpenLDAP server ) access to Alfresco and other server applications implemented in the future Given: All Servers will live in the public internet cloud (Rackspace Cloud Servers) OpenVPN Server will be a Linux disto, probably Ubuntu 9.x, installed on same server as Alfresco (at least to start) Staff will access server applications and resources from client sites, hotels, trains, planes, coffee shops or their homes over various ISP, using their company laptops or personal home desktops. Based on my Research thus far, to accomplish this, I'll need: OpenVPN with Bridging Enabled to create a star shaped "virtual" LAN http://openvpn.net/index.php/open-source/documentation/miscellaneous/76-ethernet-bridging.html A Road Warrior Network Configuration, as described in this Shorewall article (lower down the page) http://www.shorewall.net/OPENVPN.html Configure bridge addressesing (probably DHCP) http://openvpn.net/index.php/open-source/faq.html#bridge-addressing Configure CIFS / Samba to accept VPN IP address http://serverfault.com/questions/137933/howto-access-samba-share-over-vpn-tunnel Set up Client software, with keys configured for access (potentially through a OpenVPN-Sa client portal) http://www.openvpn.net/index.php/access-server/download-openvpn-as/221-installation-overview.html

    Read the article

  • How expensive to run PC 24/7 or how to figure out how to determine it?

    - by jasondavis
    I realize this question is difficult to answer as it would be different based on users location, what there PC is doing and what hardware it consist of, along with other factors but I am hoping someone could give me a very rough estimate. I have always ran many PC's in my home 24/7 and I am just now looking at it from a money/cost of electric point of view. 1) I live in Central Florida. Can anyone guesstomate/estimate the avaerage monthly or daily cost of running your average PC? Intel quad core processor, 1 SSD drive for OS and programs and 4-5 1-2 TB hard drives in a RAID setup for data. 750watt PSU. What would your guess be? 2) Also is there an accurate way to figure this out (non-super technical and confusing to a non-math person please) Also I have seen those kill-a-watt devices, do they figure this kind of stuff out for you? 3) Does a larger PSU make your PC consume more power? Thanks for any help, you can most likely tell I am somewhat lost about this!

    Read the article

  • Windows 7 machine, can't connect remotely until after ping

    - by rjohnston
    I have a Windows 7 (Home Premium) machine that doubles as a media centre and subversion server. There's a couple of problems with this setup, when connecting to the server from an XP (SP3) machine: Firstly, the machine won't respond to it's machine name until after it's IP address has been pinged. Here's an example: Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Rob>ping damascus Ping request could not find host damascus. Please check the name and try again. C:\Documents and Settings\Rob>ping 192.168.1.17 Pinging 192.168.1.17 with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time=2ms TTL=128 ... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Documents and Settings\Rob>ping damascus Pinging damascus [192.168.1.17] with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time<1ms TTL=128 .... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\Documents and Settings\Rob> Likewise, subversion commands with either the machine name or IP address will fail until the machine's IP address is pinged. Occasionally, the machine won't respond to pings on it's IP address, it'll just come back with "Request timed out". The svn server is VisualSVN, if that helps... Any ideas?

    Read the article

  • Using smartctl to get vendor specific Attributes from ssd drive behind a SmartArray P410 controller

    - by Lairsdragon
    Recently I have deployed some HP server with SSD's behind a SmartArray P410 controller. While not official supported from HP the server work well sofar. Now I like to get wear level info's, error statistics etc from the drive. While the SA P410 supports a passthru of the SMART Command to a single drive in the array the output I was not able to the the interesting things from the drive. In this case especially the value the Wear level indicator is from interest for me (Attr.ID 233), but this is ony present if the drive is directly attanched to a SATA Controller. smartctl on directly connected ssd: # smartctl -A /dev/sda smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF READ SMART DATA SECTION === SMART Attributes Data Structure revision number: 5 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0000 100 000 000 Old_age Offline In_the_past 0 4 Start_Stop_Count 0x0000 100 000 000 Old_age Offline In_the_past 0 5 Reallocated_Sector_Ct 0x0002 100 100 000 Old_age Always - 0 9 Power_On_Hours 0x0002 100 100 000 Old_age Always - 8561 12 Power_Cycle_Count 0x0002 100 100 000 Old_age Always - 55 192 Power-Off_Retract_Count 0x0002 100 100 000 Old_age Always - 29 232 Unknown_Attribute 0x0003 100 100 010 Pre-fail Always - 0 233 Unknown_Attribute 0x0002 088 088 000 Old_age Always - 0 225 Load_Cycle_Count 0x0000 198 198 000 Old_age Offline - 508509 226 Load-in_Time 0x0002 255 000 000 Old_age Always In_the_past 0 227 Torq-amp_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 228 Power-off_Retract_Count 0x0002 000 000 000 Old_age Always FAILING_NOW 0 smartctl on P410 connected ssd: # ./smartctl -A -d cciss,0 /dev/cciss/c1d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net (Right, it is complety empty) smartctl on P410 connected hdd: # ./smartctl -A -d cciss,0 /dev/cciss/c0d0 smartctl 5.39.1 2010-01-28 r3054 [x86_64-unknown-linux-gnu] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net Current Drive Temperature: 27 C Drive Trip Temperature: 68 C Vendor (Seagate) cache information Blocks sent to initiator = 1871654030 Blocks received from initiator = 1360012929 Blocks read from cache and sent to initiator = 2178203797 Number of read and write commands whose size <= segment size = 46052239 Number of read and write commands whose size > segment size = 0 Vendor (Seagate/Hitachi) factory information number of hours powered up = 3363.25 number of minutes until next internal SMART test = 12 Do I hunt here a bug, or is this a limitation of the p410 SMART cmd Passthru?

    Read the article

  • Installing Silverstripe on 000webhost.com (free web host)

    - by benwad
    Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it just refreshes the install.php page. It doesn't even overwrite the .htaccess file. 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how. EDIT: I managed to get to the next page but now there is another warning which is stopping it installing: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701

    Read the article

  • Unable to connect to CopSSH when running Windows service, works when running sshd directly

    - by Joe Enos
    I've been using CopSSH (that uses OpenSSH and Cygwin, so I don't know which of the three is the problem) as my SSH server application at home on Windows 7 Ultimate 32 bit. I have used it for about a year with no real problems, other than it sometimes takes 2 or 3 connection attempts to get through, but it's always worked within a few attempts. A few days ago, it just stopped working. The Windows service is still running, and I've rebooted, restarted the service, etc. with no change. On the client (using Putty on Windows), I get the message "Software caused connection abort". On the server, my event viewer registers the following: fatal: Write failed: Socket operation on non-socket I finally got it working, but only by executing sshd.exe directly from the command line on the server. No special flags or options, just straight execution, and then when I connect remotely, it goes through. I do have firewall and anti-virus software which appears to be configured properly, but the fact that things work when running sshd.exe also indicates that the firewall is fine. I thought the service and executable did exactly the same thing, but apparently there's some difference. Does anyone have any ideas on where I should look for the problem? If I can't find something, I suppose I can write a Windows service or scheduled task that fires off sshd.exe directly and ensures that it stays running, but that's kind of a last resort, since it's just wrapping around something that should already work. I appreciate your help.

    Read the article

  • Password Manager that allows syncing accross platforms

    - by lexu
    I use OS X, Linux, Solaris and windows for work and from home. There are good tools that allow me to manage the many logins/passwords required platform independently. But mostly they expect me to carry a thumb-drive around or require direct access to a central location (a sky drive in the cloud). The thumb-drive is too easily lost (= synchronized backup needed), the central location not always reachable/ mountable. Besides company policy rightly prevents this often. Is there a tool that allows me to add passwords locally and then syncs it's DB with the "mother-ship" later. Or is there another approach that you use, that solves my problem? EDIT My question is more about "synchronize" than cross platform. I've evaluated (=read feature list) some good cross platform tools, but need one that does the synchronizing for me. By synchronize I mean "merge two versions" not "replace (hopefully) old file with new." I'm not sure I'm always disciplined/awake enough to prevent data loss. UPDATE Lifehacker just posted that AgileSolutions now have a beta version of 1Password for Windows.

    Read the article

  • Changing Mac OS X 10.6 Routing after VPN'd In

    - by Matt Rogish
    I have a coffee shop around the corner that I use to do some work when I want to get away from home. They offer free wi-fi and I then use my Mac 10.6 VPN to log into my work network. I have "Send all traffic over VPN connection" checked. Before, their network was 10.0.0.x. I think they got a new router because it's now 192.168.2.x However, this interferes with one of the subnets at work so now I can't visit 192.168.2.x at work. So: 1) Office network: VPN gives IPs as 192.168.1.x. Another network is 192.168.2.x 2) Coffee network: Gives IPs as 192.168.2.x I think if I set a route to send all 2.x traffic over the tunnel, it would blow up my routing to their system, right? What should I do? I know the individual IPs of the servers I want... Maybe I could add each one, or can I add all of them minus the default gateway of their router? How do I set that up "temporarily" in my Mac? Thanks!!

    Read the article

  • Windows Bluescreen - atikmpag.sys

    - by Mochan
    Information Name: atikmpag.sys bluescreen (BSOD or BlueScreen of Death) Error code: 0x00000116 Appears when: Playing games, watching videos Can be reproduced: Yes Cause: Graphics Card is the main assumption System Specifications Before we begin - I will inform you of my specifications. OS: Windows 7 x64 Home Edition Model: Dell Inspiron 15R Special Edition (aka Inspiron 7520) (Add 2GB of RAM to the model linked) Hard Drive: 1TB CPU: Intel Quad-Core i7 Sandy Bridge (I think) Processor at 2.10GHz (I think it can be clocked to 3GHz?) RAM: 6GB (I think 1 x 4GB and 1 x 2GB) Display: 15.6" HD (1366x768) Graphics: AMD Radeon HD 7500M 2GB Details So now that you know some basics about my computer, I'll get to the problem. Being an Ubuntu user I hardly use Windows, but occasionally I do. Like to run Skyrim and other games incompatible with Linux and WINE. The new Sims 3 Seasons patch is also now not supported. When playing these two games and other ones, theoretically. I have also heard others saying that while watching HD movies and video series it also happens. While watching the bluescreen as it happens, I see it is the 'atikmpag.sys' error. I have not installed much and nothing significant. I think I have downloaded Skyrim, Firefox and The Sims 3. I haven't done much more... since Ubuntu is definitely the best in comparison! (No hate, just a joke :P). I can reproduce it easily (just by running a game for less than a minute). It is always there each time, but it's never at a specific time or anything. So far I have found that it may be caused by lack of power to the graphics card, or it may be damaged or fried. Since I've had the computer for a mere 4 months (and have had other problems with it also). I have contacted Dell but they are useless beyond belief. Anyone with any information, solutions or details are encouraged to share your knowledge, as it would be immensely appreciated.

    Read the article

  • Password Cracking Windows Accounts

    - by Kevin
    At work we have laptops with encrypted harddrives. Most developers here (on occasion I have been guilty of it too) leave their laptops in hibernate mode when they take them home at night. Obviously, Windows (i.e. there is a program running in the background which does it for windows) must have a method to unencrypt the data on the drive, or it wouldn't be able to access it. That being said, I always thought that leaving a windows machine on in hibernate mode in a non-secure place (not at work on a lock) is a security threat, because someone could take the machine, leave it running, hack the windows accounts and use it to encrypt the data and steal the information. When I got to thinking about how I would go about breaking into the windows system without restarting it, I couldn't figure out if it was possible. I know it is possible to write a program to crack windows passwords once you have access to the appropriate file(s). But is it possible to execute a program from a locked Windows system that would do this? I don't know of a way to do it, but I am not a Windows expert. If so, is there a way to prevent it? I don't want to expose security vulnerabilities about how to do it, so I would ask that someone wouldn't post the necessary steps in details, but if someone could say something like "Yes, it's possible the USB drive allows arbitrary execution," that would be great! EDIT: The idea being with the encryption is that you can't reboot the system, because once you do, the disk encryption on the system requires a login before being able to start windows. With the machine being in hibernate, the system owner has already bypassed the encryption for the attacker, leaving windows as the only line of defense to protect the data.

    Read the article

  • SQL 2005 Install completly broken on laptop.

    - by ProfKaos
    My problems started when I set up an exploratory domain controller at home. During that process, I changed the name of my laptop, from 'erisia' to 'erisia-laptop', and this resulted in me losing my admin account on SQL Server 2005 on my laptop. SQL Server seems to store the machine name as part of the user name, so now my local admin account is 'erisia-laptop\brady', which SQL server didn't recognise. I thought I'd cut my losses and just re-install SQL 2005, but the first install was aborted, so I tried a complete uninstall, followed by the new install. The latter didn't work while the former worked way too well. Now every attempt at installing SQL Server 2005 SP2 on my laptop running XP SP3 ends in sadness, with MSXML6 being the cause, because it won't install on this OS version. WTF? Does anyone know what I can do to get SQL 2005 installed? It's the only full admin DB tool I have. SQL 2008 Express that installed with VS 2010 Beta 2 doesn't allow much server admin.

    Read the article

  • OpenLDAP Authentication UID vs CN issues

    - by user145457
    I'm having trouble authenticating services using uid for authentication, which I thought was the standard method for authentication on the user. So basically, my users are added in ldap like this: # jsmith, Users, example.com dn: uid=jsmith,ou=Users,dc=example,dc=com uidNumber: 10003 loginShell: /bin/bash sn: Smith mail: [email protected] homeDirectory: /home/jsmith displayName: John Smith givenName: John uid: jsmith gecos: John Smith gidNumber: 10000 cn: John Smith title: System Administrator But when I try to authenticate using typical webapps or services like this: jsmith password I get: ldapsearch -x -h ldap.example.com -D "cn=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" Enter LDAP Password: ldap_bind: Invalid credentials (49) But if I use: ldapsearch -x -h ldap.example.com -D "uid=jsmith,ou=Users,dc=example,dc=com" -W -b "dc=example,dc=com" It works. HOWEVER...most webapps and authentication methods seem to use another method. So on a webapp I'm using, unless I specify the user as: uid=smith,ou=users,dc=example,dc=com Nothing works. In the webapp I just need users to put: jsmith in the user field. Keep in mind my ldap is using the "new" cn=config method of storing settings. So if someone has an obvious ldif I'm missing please provide. Let me know if you need further info. This is openldap on ubuntu 12.04. Thanks, Dave

    Read the article

  • Can't ping my Window 7 machine from within a Windows XP virtual machine

    - by Jonathan Conway
    I have Windows 7 installed as my primary operating system, on a laptop that's on my home network (wireless). I'm using Microsoft Virtual PC 2007 SP1 to run a virtual machine of Windows XP SP3, in which I want to access the Windows 7 instance, both to browse a shared folder and access the local Apache server. So far I can ping my Windows 7 IP address (IPv4) and access the apache server through the web browser through HTTP. However using my machine name never seems to work. Pinging it fails, and I can't access my apache server using it either. The problem seems to be something to do with my machine's name being registered under IPv6 rather than IPv4. I'm at a loss what to do. Should I try to set up IPv6 on the virtual machine? Not sure how to go about that. Or maybe I should somehow get my machine name on Windows 7 to work with IPv4? Although I think it already does, because I can ping it from a separate box (running Ubuntu), which is only registered under IPv6.

    Read the article

  • AuthBasicProvider: failover not working when the first LDAP is down?

    - by quanta
    I've been trying to setup redundant LDAP servers with Apache 2.2.3. /etc/httpd/conf.d/authn_alias.conf <AuthnProviderAlias ldap master> AuthLDAPURL ldap://192.168.5.148:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> <AuthnProviderAlias ldap slave> AuthLDAPURL ldap://192.168.5.199:389/dc=domain,dc=vn?cn AuthLDAPBindDN cn=anonymous,ou=it,dc=domain,dc=vn AuthLDAPBindPassword pa$$w0rd </AuthnProviderAlias> /etc/httpd/conf.d/authz_ldap.conf # # mod_authz_ldap can be used to implement access control and # authenticate users against an LDAP database. # LoadModule authz_ldap_module modules/mod_authz_ldap.so <IfModule mod_authz_ldap.c> <Location /> AuthBasicProvider master slave AuthzLDAPAuthoritative Off AuthType Basic AuthName "Authorization required" AuthzLDAPMemberKey member AuthUserFile /home/setup/svn/auth-conf AuthzLDAPSetGroupAuth user require valid-user AuthzLDAPLogLevel error </Location> </IfModule> If I understand correctly, mod_authz_ldap will try to search users in the second LDAP if the first server is down or OpenLDAP on it is not running. But in practice, it does not happen. Tested by stopping LDAP on the master, I get the "500 Internal Server Error" when accessing to the Subversion repository. The error_log shows: [11061] auth_ldap authenticate: user quanta authentication failed; URI / [LDAP: ldap_simple_bind_s() failed][Can't contact LDAP server] Did I misunderstand?

    Read the article

  • Mac Mini drive problems but SMART verified: bad hard drive or controller?

    - by Zac Thompson
    I have a 3-year-old Intel Mac Mini at home. About a month ago, it stopped booting from the hard drive (internal, SATA, 80GB). I tried booting from the Install Disc to repair the filesystem but Disk Utility was unable to do so ("invalid node structure"). I was also unable to use the hard drive in the Terminal from the Install Disc nor from an Ubuntu boot CD ("DRDY err"). I could see the contents of some directories, but others would give an error and I would get failures when trying to copy files. At this point I was sure the filesystem was hosed and I'd want to reformat at least. DiskWarrior was able to let me retrieve the data files I was interested in, which are now copied to an external hard drive, but it reported a high number of problems ("speed reduced by disk malfunction" count was over 2000) when in the process of trying to rebuild the directory for the drive. It also would not let me use the rebuilt directory to replace the one on the drive; it claimed the disk errors prevented recovery in this way. Under normal circumstances I would now assume that the drive itself was going bad: DiskWarrior's "disk malfunction" error above is supposed to imply hardware problems. My initial plan was to buy a replacement for the internal 2.5" drive. However: Disk Utility, command-line tools and DiskWarrior had reported all along that the SMART status of the drive was okay/Verified. So I'm now worried that the drive hardware is actually fine, and that the problems were due to a disk controller that has gone "bad" somehow. If this is the case, I'll probably just replace the whole computer. Any advice on how I can tell what is to blame? I don't have a lot of extra hardware sitting around, so I don't have the option of simply dropping the drive in another machine or popping another hard drive inside the Mini.

    Read the article

  • Firefox does not upgrade properly (infinite installation loop without success)

    - by Mehper C. Palavuzlar
    I've been using Firefox for a long time but I have a problem with upgrading process now. As you know, Firefox automatically checks for the latest version and downloads it, and when it is ready to be installed it starts the installation process as usual. Last month, when I clicked on "OK, install v3.6.2", the process started but couldn't be finished properly. FF gave a message like that: "Installation cannot be completed, please restart Firefox to retry". When I restarted FF, the same thing happened, and the process entered in an infinite loop. I restarted my PC and clicked on FF icon, and again the installation process began and went into the infinite loop. My solution to this problem was to download FF 3.6.2 and manually install it after killing firefox.exe. Today, FF proposed me to install v3.6.3 and again the same problem occured. I manually downloaded FF 3.6.3 and installed it successfully. Anyone experiencing this problem? In case you want to know, I did not install any new addons in the last few months, and my FF operates without problems. I'm using Windows 7 Home Pro x64.

    Read the article

  • How to configure SCSI hard drives and RAID for Poweredge 2850 web server

    - by Saul
    I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

    Read the article

  • [URGENT HELP PLEASE]USB Flash Drive Problem!

    - by Daren
    Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

    Read the article

  • Mac OSX: which folders should ClamXav Sentry watch?

    - by trolle3000
    I'm using ClamXav on my mac. I've read this, and I am aware of the whole macs-need-no-AV-but-they-do-anyway discussion. I guess that's why I would feel like a real ass if I somehow managed to compromise my system! So ClamXav has been downloaded and ClamXav Sentry set up to start on log-in, but it doesn't really do anything before you tell it to. Specifically, you have to tell it which folders to watch for virusses/vira so I'm wondering, where are good places to look? Currently it's been set up to look the following places: In the home folder: ~/Downloads ~/Library/Caches ~/Library/Contextual Menu Items ~/Library/Cookies ~/Library/Internet Plug-Ins ~/Library/LaunchAgents In my system folder: /Library/Application Support /Library/Caches /Library/Contextual Menu Items /Library/Cookies /Library/Internet Plug-Ins /Library/LaunchAgents /Library/LaunchDaemons /Library/Startupitems Basically, this is 100% conjecture. All (most of) the folders have something to do with internet and things that start up automatically, so I'm guessing that's where vira go. But still, the qustion: Which folders should ClamXav Sentry watch, if any? FYI, I'm not using any mail app's, but please include that in your answer for anyone who might be interested. Cheers!

    Read the article

  • Errors to do with modules when using net-snmp utils

    - by bob
    I was using the net-snmp packages that come with my linux distro (version 5.3.2.2), but wanted to do some work with the latest version of net-snmp (5.7), so tried compiling and installing the new source. It seemed to work ok but now I'm getting a load of errors when use net-snmp utils (snmpget, snmpset snmpwalk etc..) for example: $ snmptranslate -On SNMPv2-MIB::system.sysDescr MIB search path: /home/me/.snmp/mibs:/usr/local/share/snmp/mibs Cannot find module (SNMPv2-SMI) At line 6 in /usr/local/share/snmp/mibs/SNMPv2-MIB.txt Cannot find module (SNMPv2-TC): At line 9 in /usr/local/share/snmp/mibs/SNMPv2-MIB.txt Cannot find module (SNMPv2-MIB): At line 9 in (none) : <a lot of similar lines> : Cannot find module (NET-SNMP-VACM-MIB): At line 9 in (none) .1.3.6.1.2.1.1.1 From this I assumed perhaps that I was missing mibs from the 'MIB search path', so I looked at the first error 'Cannot find module (SNMPv2-SMI)', however it seems to be in the right directory: $ ls /usr/local/share/snmp/mibs/*SNMPv2-SMI* /usr/local/share/snmp/mibs/SNMPv2-SMI.txt And the same result for the other in the list.. so I'm wondering if anybody knows why it might not be finding the modules even though they seem to be in the search path?

    Read the article

  • Force spin-down of external hard-drive on linux (raspberry pi)

    - by user258346
    I'm currently setting up a home-server using a Raspberry Pi with an external hard-disk connected via usb. However, my hard-drive will never spin down when being idle. I tried already the hints provided at raspberrypi.org ... without any success. 1.) sudo hdparm -S5 /dev/sda returns /dev/sda: setting standby to 5 (25 seconds) SG_IO: bad/missing sense data, sb[]: 70 00 04 00 00 00 00 0a 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 2.) sudo hdparm -y /dev/sda returns /dev/sda: issuing standby command SG_IO: bad/missing sense data, sb[]: 70 00 04 00 00 00 00 0a 00 00 00 00 44 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ...and 3.) sudo sdparm --flexible --command=stop /dev/sda returns /dev/sda: HDD 1234 ... without spin-down of the drive. I use the following hardware: Inateck FDU3C-2 dual Ports USB 3.0 HDD docking station Western Digital WD10EZRX Green 1TB Is it possible, that the sent spin-down-signals are somewhere overwritten/lost/ignored?

    Read the article

< Previous Page | 509 510 511 512 513 514 515 516 517 518 519 520  | Next Page >