virtual keyboard - Page 517

Renaming VLAN Interfaces in Linux

- by rhololkeolke

I need to know how to rename VLAN interfaces. I'm currently running Ubuntu 11.04. I'm running a networking application that takes frames on one interface applies things like delays and errors and then forwards the frames out another interface. The default naming convention which names things <interface>.<vlan> e.g. eth0.2 will not work for my purposes because the program which parses the configuration script for the networking application doesn't like the decimal in the interface name. I ran vconfig set_name_type VLAN_PLUS_VID which solves the decimal in the interface name problem, however, I can then no longer assign the same vlan id to multiple interfaces because they have the same name. I know how to change physical interface names using udev rules, but because the vlan's will have the same MAC address and they aren't physical interfaces I can't use those rules to rename the interfaces. Is there a way to rename any interface in linux, including the virtual ones? Is there a way to specify your own naming convention for config set_name_type option without having to recompile the source of vconfig?

Read the article

Copy past speed very slow for a large number of files on Windows [closed]

- by Arno2501

I've run the following test I've created a folder containing 15'000 files of 400 bytes using this batch : @ECHO off SET times=15000 FOR /L %%i IN (1,1,%times%) DO ( fsutil file createnew filename%%i.txt 400 ) then I copy past it on my Windows Computer using this command : robocopy LargeNumberOfFiles\ LargeNumberOfFiles2\ After it has completed I can see that the transfer rate was 915810 Bytes/sec this is less than 1 MB/s. It took me several seconds to copy 7 MBytes Please note that this is very slow. I've tried the same with a folder with a single file of 50 Mbytes and the transfer rate is 1219512195 Bytes/sec. (yeah GB/s) instantaneous. Why copying large number of files take so much time - ressources on a windows filesystem ? Please note that I've tried to do the same on a linux system which runs on the same computer in a virtual machine (vmware player) with ext3 filesystem. I use the cp command and the copy is instantaneous ! Please also note the following : no antivirus I've tested that behaviour on multiple windows computers (always ntfs) i always get comparable results (transfer rate under 1MB/s avg 7-8 seconds to copy 7 MBytes) I've tested on multiple linux ext3 system the copy is always instantaneous for that amount (15000 files of 400 bytes) The question is about understanding what makes windows filesystem so slow to copy large number of files compared to a linux one for instance.

Read the article

Glassfish 3 Cant update JDK no way

- by Parhs

Hello.. I was using 1.6.0_19 jdk and installed 1.6.0_20 jdk.. Glassfish doesnt like that... Here are my windows environment variables.. ALLUSERSPROFILE=C:\ProgramData ANT_HOME=C:\apache-ant-1.8.1\ APPDATA=C:\Users\Parhs\AppData\Roaming CommonProgramFiles=C:\Program Files\Common Files COMPUTERNAME=PARHS-PC ComSpec=C:\Windows\system32\cmd.exe FP_NO_HOST_CHECK=NO HOMEDRIVE=C: HOMEPATH=\Users\Parhs JAVA_HOME=C:\Program Files\Java\jdk1.6.0_20\ LOCALAPPDATA=C:\Users\Parhs\AppData\Local LOGONSERVER=\\PARHS-PC NUMBER_OF_PROCESSORS=2 OS=Windows_NT Path=C:\Program Files\PHP\;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wb em;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files\Toshiba\Bluetoot h Toshiba Stack\sys\;C:\Program Files\Microsoft SQL Server\90\Tools\binn\;C:\apa che-ant-1.8.1\bin PATHEXT=.COM;.EXE;.BAT;.CMD;.VBS;.VBE;.JS;.JSE;.WSF;.WSH;.MSC PHPRC=C:\Program Files\PHP\php.ini PROCESSOR_ARCHITECTURE=x86 PROCESSOR_IDENTIFIER=x86 Family 6 Model 14 Stepping 8, GenuineIntel PROCESSOR_LEVEL=6 PROCESSOR_REVISION=0e08 ProgramData=C:\ProgramData ProgramFiles=C:\Program Files PROMPT=$P$G PSModulePath=C:\Windows\system32\WindowsPowerShell\v1.0\Modules\ PUBLIC=C:\Users\Public SESSIONNAME=Console SystemDrive=C: SystemRoot=C:\Windows TEMP=C:\Users\Parhs\AppData\Local\Temp TMP=C:\Users\Parhs\AppData\Local\Temp USERDOMAIN=Parhs-PC USERNAME=Parhs USERPROFILE=C:\Users\Parhs VS90COMNTOOLS=C:\Program Files\Microsoft Visual Studio 9.0\Common7\Tools\ windir=C:\Windows Also here is my asenv.bat REM DO NOT ALTER OR REMOVE COPYRIGHT NOTICES OR THIS HEADER. REM REM Copyright 2004-2009 Sun Microsystems, Inc. All rights reserved. REM REM Use is subject to License Terms REM set AS_IMQ_LIB=....\mq\lib set AS_IMQ_BIN=....\mq\bin set AS_CONFIG=..\config set AS_INSTALL=.. set AS_DEF_DOMAINS_PATH=..\domains set AS_DERBY_INSTALL=....\javadb set AS_JAVA="C:\Program Files\Java\jdk1.6.0_20" And although restarting system and server i am getting this report Operating System Information: Name of the Operating System: Windows 7 Binary Architecture name of the Operating System: x86, Version: 6.1 Number of processors available on the Operating System: 2 System load on the available processors for the last minute: -1.0. (Sum of running and queued runnable entities per minute) General Java Runtime Environment Information for the VM: 6152@Parhs-PC JRE BootClassPath: C:\glassfishv3\glassfish/modules/endorsed\javax.annotation.jar;C:\glassfishv3\glassfish/modules/endorsed\jaxb-api-osgi.jar;C:\glassfishv3\glassfish/modules/endorsed\webservices-api-osgi.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\resources.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\rt.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\sunrsasign.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\jsse.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\jce.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\charsets.jar;C:\Program Files\Java\jdk1.6.0_19\jre\classes;C:\glassfishv3\glassfish\lib\monitor\btrace-boot.jar JRE ClassPath: C:\glassfishv3\glassfish\modules\glassfish.jar;C:\glassfishv3\glassfish\lib\monitor\btrace-agent.jar JRE Native Library Path: C:\Program Files\Java\jdk1.6.0_19\bin;.;C:\Windows\Sun\Java\bin;C:\Windows\system32;C:\Windows;C:\Program Files\PHP\;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files\Toshiba\Bluetooth Toshiba Stack\sys\;C:\Program Files\Microsoft SQL Server\90\Tools\binn\;C:\apache-ant-1.8.1\bin JRE name: Java HotSpot(TM) Client VM Vendor: Sun Microsystems Inc. Version: 16.2-b04 List of System Properties for the Java Virtual Machine: ANTLR_USE_DIRECT_CLASS_LOADING = true AS_CONFIG = C:\glassfishv3\glassfish\config\..\config AS_DEF_DOMAINS_PATH = C:\glassfishv3\glassfish\config\..\domains AS_DERBY_INSTALL = C:\glassfishv3\glassfish\config\..\..\javadb AS_IMQ_BIN = C:\glassfishv3\glassfish\config\..\..\mq\bin AS_IMQ_LIB = C:\glassfishv3\glassfish\config\..\..\mq\lib AS_INSTALL = C:\glassfishv3\glassfish\config\.. AS_JAVA = C:\Program Files\Java\jdk1.6.0_20\jre GlassFish_Platform = Felix awt.toolkit = sun.awt.windows.WToolkit catalina.base = C:\glassfishv3\glassfish\domains\domain1 catalina.home = C:\glassfishv3\glassfish\domains\domain1 catalina.useNaming = false com.sun.aas.configRoot = C:\glassfishv3\glassfish\config com.sun.aas.derbyRoot = C:\glassfishv3\javadb com.sun.aas.domainsRoot = C:\glassfishv3\glassfish\domains com.sun.aas.hostName = Parhs-PC com.sun.aas.imqBin = C:\glassfishv3\mq\bin com.sun.aas.imqLib = C:\glassfishv3\mq\lib com.sun.aas.installRoot = C:\glassfishv3\glassfish com.sun.aas.installRootURI = file:/C:/glassfishv3/glassfish/ com.sun.aas.instanceName = server com.sun.aas.instanceRoot = C:\glassfishv3\glassfish\domains\domain1 com.sun.aas.instanceRootURI = file:/C:/glassfishv3/glassfish/domains/domain1/ com.sun.aas.javaRoot = C:\Program Files\Java\jdk1.6.0_19\jre com.sun.enterprise.config.config_environment_factory_class = com.sun.enterprise.config.serverbeans.AppserverConfigEnvironmentFactory com.sun.enterprise.hk2.cacheDir = C:\glassfishv3\glassfish\domains\domain1\osgi-cache\felix com.sun.enterprise.jaccprovider.property.repository = C:\glassfishv3\glassfish\domains\domain1/generated/policy com.sun.enterprise.security.httpsOutboundKeyAlias = s1as common.loader = ${catalina.home}/common/classes,${catalina.home}/common/endorsed/*.jar,${catalina.home}/common/lib/*.jar eclipselink.security.usedoprivileged = true ejb.home = C:\glassfishv3\glassfish\modules\ejb felix.config.properties = file:/C:/glassfishv3/glassfish/osgi/felix/conf/config.properties felix.fileinstall.bundles.new.start = true felix.fileinstall.debug = 1 felix.fileinstall.dir = C:\glassfishv3\glassfish/modules/autostart/ felix.fileinstall.poll = 5000 felix.system.properties = file:/C:/glassfishv3/glassfish/osgi/felix/conf/system.properties file.encoding = Cp1253 file.encoding.pkg = sun.io file.separator = \ glassfish.version = GlassFish v3 (build 74.2) hk2.startup.context.args = #Mon Jun 07 20:27:37 EEST 2010 -startup-classpath=C\:\\glassfishv3\\glassfish\\modules\\glassfish.jar;C\:\\glassfishv3\\glassfish\\lib\\monitor\\btrace-agent.jar __time_zero=1275931657334 hk2.startup.context.mainModule=org.glassfish.core.kernel -startup-args=--domain,,,domain1,,,--domaindir,,,C\:\\glassfishv3\\glassfish\\domains\\domain1 --domain=domain1 -startup-classname=com.sun.enterprise.glassfish.bootstrap.ASMain --domaindir=C\:\\glassfishv3\\glassfish\\domains\\domain1 hk2.startup.context.root = C:\glassfishv3\glassfish\modules http.nonProxyHosts = localhost|127.0.0.1|Parhs-PC java.awt.graphicsenv = sun.awt.Win32GraphicsEnvironment java.awt.printerjob = sun.awt.windows.WPrinterJob java.class.path = C:\glassfishv3\glassfish\modules\glassfish.jar;C:\glassfishv3\glassfish\lib\monitor\btrace-agent.jar java.class.version = 50.0 java.endorsed.dirs = C:\glassfishv3\glassfish/modules/endorsed;C:\glassfishv3\glassfish/lib/endorsed java.ext.dirs = C:\Program Files\Java\jdk1.6.0_19\jre/lib/ext;C:\Program Files\Java\jdk1.6.0_19\jre/jre/lib/ext;C:\glassfishv3\glassfish\domains\domain1/lib/ext java.home = C:\Program Files\Java\jdk1.6.0_19\jre java.io.tmpdir = C:\Users\Parhs\AppData\Local\Temp\ java.library.path = C:\Program Files\Java\jdk1.6.0_19\bin;.;C:\Windows\Sun\Java\bin;C:\Windows\system32;C:\Windows;C:\Program Files\PHP\;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\WindowsPowerShell\v1.0\;C:\Program Files\Toshiba\Bluetooth Toshiba Stack\sys\;C:\Program Files\Microsoft SQL Server\90\Tools\binn\;C:\apache-ant-1.8.1\bin java.net.useSystemProxies = true java.rmi.server.randomIDs = true java.runtime.name = Java(TM) SE Runtime Environment java.runtime.version = 1.6.0_19-b04 java.security.auth.login.config = C:\glassfishv3\glassfish\domains\domain1/config/login.conf java.security.policy = C:\glassfishv3\glassfish\domains\domain1/config/server.policy java.specification.name = Java Platform API Specification java.specification.vendor = Sun Microsystems Inc. java.specification.version = 1.6 java.util.logging.config.file = C:\glassfishv3\glassfish\domains\domain1\config\logging.properties java.vendor = Sun Microsystems Inc. java.vendor.url = http://java.sun.com/ java.vendor.url.bug = http://java.sun.com/cgi-bin/bugreport.cgi java.version = 1.6.0_19 java.vm.info = mixed mode java.vm.name = Java HotSpot(TM) Client VM java.vm.specification.name = Java Virtual Machine Specification java.vm.specification.vendor = Sun Microsystems Inc. java.vm.specification.version = 1.0 java.vm.vendor = Sun Microsystems Inc. java.vm.version = 16.2-b04 javax.net.ssl.keyStore = C:\glassfishv3\glassfish\domains\domain1/config/keystore.jks javax.net.ssl.keyStorePassword = changeit javax.net.ssl.trustStore = C:\glassfishv3\glassfish\domains\domain1/config/cacerts.jks javax.net.ssl.trustStorePassword = changeit javax.rmi.CORBA.PortableRemoteObjectClass = com.sun.corba.ee.impl.javax.rmi.PortableRemoteObject javax.rmi.CORBA.StubClass = com.sun.corba.ee.impl.javax.rmi.CORBA.StubDelegateImpl javax.rmi.CORBA.UtilClass = com.sun.corba.ee.impl.javax.rmi.CORBA.Util javax.security.jacc.PolicyConfigurationFactory.provider = com.sun.enterprise.security.provider.PolicyConfigurationFactoryImpl jdbc.drivers = org.apache.derby.jdbc.ClientDriver jpa.home = C:\glassfishv3\glassfish\modules\jpa line.separator = org.glassfish.web.rfc2109_cookie_names_enforced = false org.jvnet.hk2.osgimain.autostartBundles = osgi-adapter.jar, org.apache.felix.shell.jar, org.apache.felix.shell.remote.jar, org.apache.felix.configadmin.jar, org.apache.felix.fileinstall.jar org.jvnet.hk2.osgimain.bundlesDir = C:\glassfishv3\glassfish\modules org.jvnet.hk2.osgimain.excludedSubDirs = autostart/ org.omg.CORBA.ORBClass = com.sun.corba.ee.impl.orb.ORBImpl org.omg.CORBA.ORBSingletonClass = com.sun.corba.ee.impl.orb.ORBSingleton org.osgi.framework.storage = C:\glassfishv3\glassfish\domains\domain1\osgi-cache\felix os.arch = x86 os.name = Windows 7 os.version = 6.1 osgi.shell.telnet.ip = 127.0.0.1 osgi.shell.telnet.maxconn = 1 osgi.shell.telnet.port = 6666 package.access = package.definition = path.separator = ; security.home = C:\glassfishv3\glassfish\modules\security server.loader = ${catalina.home}/server/classes,${catalina.home}/server/lib/*.jar shared.loader = ${catalina.home}/shared/classes,${catalina.home}/shared/lib/*.jar sun.arch.data.model = 32 sun.boot.class.path = C:\glassfishv3\glassfish/modules/endorsed\javax.annotation.jar;C:\glassfishv3\glassfish/modules/endorsed\jaxb-api-osgi.jar;C:\glassfishv3\glassfish/modules/endorsed\webservices-api-osgi.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\resources.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\rt.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\sunrsasign.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\jsse.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\jce.jar;C:\Program Files\Java\jdk1.6.0_19\jre\lib\charsets.jar;C:\Program Files\Java\jdk1.6.0_19\jre\classes;C:\glassfishv3\glassfish\lib\monitor\btrace-boot.jar sun.boot.library.path = C:\Program Files\Java\jdk1.6.0_19\jre\bin sun.cpu.endian = little sun.cpu.isalist = pentium_pro+mmx pentium_pro pentium+mmx pentium i486 i386 i86 sun.desktop = windows sun.io.unicode.encoding = UnicodeLittle sun.java.launcher = SUN_STANDARD sun.jnu.encoding = Cp1253 sun.management.compiler = HotSpot Client Compiler sun.os.patch.level = user.country = GR user.dir = C:\glassfishv3\glassfish\domains\domain1 user.home = C:\Users\Parhs user.language = el user.name = Parhs user.timezone = Europe/Athens user.variant = web.home = C:\glassfishv3\glassfish\modules\web weld.home = C:\glassfishv3\glassfish\modules\weld Why it is so damn hard??? What am i missing?

Read the article

Reflect.Emit Dynamic Type Memory Blowup

- by Firestrand

Using C# 3.5 I am trying to generate dynamic types at runtime using reflection emit. I used the Dynamic Query Library sample from Microsoft to create a class generator. Everything works, my problem is that 100 generated types inflate the memory usage by approximately 25MB. This is a completely unacceptable memory profile as eventually I want to support having several hundred thousand types generated in memory. Memory profiling shows that the memory is apparently being held by various System.Reflection.Emit types and methods though I can't figure out why. I haven't found others talking about this problem so I am hoping someone in this community either knows what I am doing wrong or if this is expected behavior. Contrived Example below: using System; using System.Collections.Generic; using System.Text; using System.Reflection; using System.Reflection.Emit; namespace SmallRelfectExample { class Program { static void Main(string[] args) { int typeCount = 100; int propCount = 100; Random rand = new Random(); Type dynType = null; for (int i = 0; i < typeCount; i++) { List<DynamicProperty> dpl = new List<DynamicProperty>(propCount); for (int j = 0; j < propCount; j++) { dpl.Add(new DynamicProperty("Key" + rand.Next().ToString(), typeof(String))); } SlimClassFactory scf = new SlimClassFactory(); dynType = scf.CreateDynamicClass(dpl.ToArray(), i); //Optionally do something with the type here } Console.WriteLine("SmallRelfectExample: {0} Types generated.", typeCount); Console.ReadLine(); } } public class SlimClassFactory { private readonly ModuleBuilder module; public SlimClassFactory() { AssemblyName name = new AssemblyName("DynamicClasses"); AssemblyBuilder assembly = AppDomain.CurrentDomain.DefineDynamicAssembly(name, AssemblyBuilderAccess.Run); module = assembly.DefineDynamicModule("Module"); } public Type CreateDynamicClass(DynamicProperty[] properties, int Id) { string typeName = "DynamicClass" + Id.ToString(); TypeBuilder tb = module.DefineType(typeName, TypeAttributes.Class | TypeAttributes.Public, typeof(DynamicClass)); FieldInfo[] fields = GenerateProperties(tb, properties); GenerateEquals(tb, fields); GenerateGetHashCode(tb, fields); Type result = tb.CreateType(); return result; } static FieldInfo[] GenerateProperties(TypeBuilder tb, DynamicProperty[] properties) { FieldInfo[] fields = new FieldBuilder[properties.Length]; for (int i = 0; i < properties.Length; i++) { DynamicProperty dp = properties[i]; FieldBuilder fb = tb.DefineField("_" + dp.Name, dp.Type, FieldAttributes.Private); PropertyBuilder pb = tb.DefineProperty(dp.Name, PropertyAttributes.HasDefault, dp.Type, null); MethodBuilder mbGet = tb.DefineMethod("get_" + dp.Name, MethodAttributes.Public | MethodAttributes.SpecialName | MethodAttributes.HideBySig, dp.Type, Type.EmptyTypes); ILGenerator genGet = mbGet.GetILGenerator(); genGet.Emit(OpCodes.Ldarg_0); genGet.Emit(OpCodes.Ldfld, fb); genGet.Emit(OpCodes.Ret); MethodBuilder mbSet = tb.DefineMethod("set_" + dp.Name, MethodAttributes.Public | MethodAttributes.SpecialName | MethodAttributes.HideBySig, null, new Type[] { dp.Type }); ILGenerator genSet = mbSet.GetILGenerator(); genSet.Emit(OpCodes.Ldarg_0); genSet.Emit(OpCodes.Ldarg_1); genSet.Emit(OpCodes.Stfld, fb); genSet.Emit(OpCodes.Ret); pb.SetGetMethod(mbGet); pb.SetSetMethod(mbSet); fields[i] = fb; } return fields; } static void GenerateEquals(TypeBuilder tb, FieldInfo[] fields) { MethodBuilder mb = tb.DefineMethod("Equals", MethodAttributes.Public | MethodAttributes.ReuseSlot | MethodAttributes.Virtual | MethodAttributes.HideBySig, typeof(bool), new Type[] { typeof(object) }); ILGenerator gen = mb.GetILGenerator(); LocalBuilder other = gen.DeclareLocal(tb); Label next = gen.DefineLabel(); gen.Emit(OpCodes.Ldarg_1); gen.Emit(OpCodes.Isinst, tb); gen.Emit(OpCodes.Stloc, other); gen.Emit(OpCodes.Ldloc, other); gen.Emit(OpCodes.Brtrue_S, next); gen.Emit(OpCodes.Ldc_I4_0); gen.Emit(OpCodes.Ret); gen.MarkLabel(next); foreach (FieldInfo field in fields) { Type ft = field.FieldType; Type ct = typeof(EqualityComparer<>).MakeGenericType(ft); next = gen.DefineLabel(); gen.EmitCall(OpCodes.Call, ct.GetMethod("get_Default"), null); gen.Emit(OpCodes.Ldarg_0); gen.Emit(OpCodes.Ldfld, field); gen.Emit(OpCodes.Ldloc, other); gen.Emit(OpCodes.Ldfld, field); gen.EmitCall(OpCodes.Callvirt, ct.GetMethod("Equals", new Type[] { ft, ft }), null); gen.Emit(OpCodes.Brtrue_S, next); gen.Emit(OpCodes.Ldc_I4_0); gen.Emit(OpCodes.Ret); gen.MarkLabel(next); } gen.Emit(OpCodes.Ldc_I4_1); gen.Emit(OpCodes.Ret); } static void GenerateGetHashCode(TypeBuilder tb, FieldInfo[] fields) { MethodBuilder mb = tb.DefineMethod("GetHashCode", MethodAttributes.Public | MethodAttributes.ReuseSlot | MethodAttributes.Virtual | MethodAttributes.HideBySig, typeof(int), Type.EmptyTypes); ILGenerator gen = mb.GetILGenerator(); gen.Emit(OpCodes.Ldc_I4_0); foreach (FieldInfo field in fields) { Type ft = field.FieldType; Type ct = typeof(EqualityComparer<>).MakeGenericType(ft); gen.EmitCall(OpCodes.Call, ct.GetMethod("get_Default"), null); gen.Emit(OpCodes.Ldarg_0); gen.Emit(OpCodes.Ldfld, field); gen.EmitCall(OpCodes.Callvirt, ct.GetMethod("GetHashCode", new Type[] { ft }), null); gen.Emit(OpCodes.Xor); } gen.Emit(OpCodes.Ret); } } public abstract class DynamicClass { public override string ToString() { PropertyInfo[] props = GetType().GetProperties(BindingFlags.Instance | BindingFlags.Public); StringBuilder sb = new StringBuilder(); sb.Append("{"); for (int i = 0; i < props.Length; i++) { if (i > 0) sb.Append(", "); sb.Append(props[i].Name); sb.Append("="); sb.Append(props[i].GetValue(this, null)); } sb.Append("}"); return sb.ToString(); } } public class DynamicProperty { private readonly string name; private readonly Type type; public DynamicProperty(string name, Type type) { if (name == null) throw new ArgumentNullException("name"); if (type == null) throw new ArgumentNullException("type"); this.name = name; this.type = type; } public string Name { get { return name; } } public Type Type { get { return type; } } } }

Read the article

Managing the layout of a Java MainFrame of Canvas3d

- by John N

Hi, Im trying to organise the layout of four canvas3d objects in a single MainFrame. Iv tried using some layout managers but none are working (or im doing it wrong). Can anyone give me advice or point me to a way to get this to display the four canvas's as a grid of four? Thanks, John public class Main { public static void Main(){ Window win = new Window(); } } import javax.media.j3d.BranchGroup; import javax.media.j3d.Canvas3D; import javax.media.j3d.Locale; import javax.media.j3d.PhysicalBody; import javax.media.j3d.PhysicalEnvironment; import javax.media.j3d.Transform3D; import javax.media.j3d.TransformGroup; import javax.media.j3d.View; import javax.media.j3d.ViewPlatform; import javax.media.j3d.VirtualUniverse; import javax.vecmath.Vector3f; import com.sun.j3d.utils.picking.PickCanvas; public class Universe { boolean camera = true; Canvas3D canvas1, canvas2, canvas3, canvas4; VirtualUniverse universe; Locale locale; TransformGroup vpTrans1, vpTransRight, vpTransFront, vpTransPers; TransformGroup mouseTransform = null; View view1, view2, view3, view4; BranchGroup scene; PickCanvas pickCanvas1 = null; PickCanvas pickCanvas2 = null; PickCanvas pickCanvas3 = null; PickCanvas pickCanvas4 = null; BranchGroup obj = new BranchGroup(); // Create a BranchGroup node for the view platform BranchGroup vpRoot = new BranchGroup(); //Temp vars for cam movement public Universe(Canvas3D c1, Canvas3D c2, Canvas3D c3, Canvas3D c4, BranchGroup scene) { this.canvas1 = c1; this.canvas2 = c2; this.canvas3 = c3; this.canvas4 = c4; this.scene = scene; // Establish a virtual universe that has a single // hi-res Locale universe = new VirtualUniverse(); locale = new Locale(universe); // Create a PhysicalBody and PhysicalEnvironment object PhysicalBody body = new PhysicalBody(); PhysicalEnvironment environment = new PhysicalEnvironment(); // Create a View and attach the Canvas3D and the physical // body and environment to the view. view1 = new View(); view1.addCanvas3D(c1); view1.addCanvas3D(c2); view1.addCanvas3D(c3); view1.addCanvas3D(c4); view1.setPhysicalBody(body); view1.setPhysicalEnvironment(environment); // Create a BranchGroup node for the view platform BranchGroup vpRoot = new BranchGroup(); // Create a ViewPlatform object, and its associated // TransformGroup object, and attach it to the root of the // subgraph. Attach the view to the view platform. Transform3D t = new Transform3D(); t.set(new Vector3f(0.0f, 0.0f, 2.0f)); ViewPlatform vp = new ViewPlatform(); vpTrans1 = new TransformGroup(t); vpTrans1.addChild(vp); vpRoot.addChild(vpTrans1); vpRoot.addChild(scene); view1.attachViewPlatform(vp); // Attach the branch graph to the universe, via the // Locale. The scene graph is now live! locale.addBranchGraph(vpRoot); } } import javax.media.j3d.BranchGroup; import javax.media.j3d.Canvas3D; import javax.media.j3d.Locale; import javax.media.j3d.PhysicalBody; import javax.media.j3d.PhysicalEnvironment; import javax.media.j3d.Transform3D; import javax.media.j3d.TransformGroup; import javax.media.j3d.View; import javax.media.j3d.ViewPlatform; import javax.media.j3d.VirtualUniverse; import javax.vecmath.Vector3f; import com.sun.j3d.utils.picking.PickCanvas; public class Universe { boolean camera = true; Canvas3D canvas1, canvas2, canvas3, canvas4; VirtualUniverse universe; Locale locale; TransformGroup vpTrans1, vpTransRight, vpTransFront, vpTransPers; TransformGroup mouseTransform = null; View view1, view2, view3, view4; BranchGroup scene; PickCanvas pickCanvas1 = null; PickCanvas pickCanvas2 = null; PickCanvas pickCanvas3 = null; PickCanvas pickCanvas4 = null; BranchGroup obj = new BranchGroup(); // Create a BranchGroup node for the view platform BranchGroup vpRoot = new BranchGroup(); //Temp vars for cam movement public Universe(Canvas3D c1, Canvas3D c2, Canvas3D c3, Canvas3D c4, BranchGroup scene) { this.canvas1 = c1; this.canvas2 = c2; this.canvas3 = c3; this.canvas4 = c4; this.scene = scene; // Establish a virtual universe that has a single // hi-res Locale universe = new VirtualUniverse(); locale = new Locale(universe); // Create a PhysicalBody and PhysicalEnvironment object PhysicalBody body = new PhysicalBody(); PhysicalEnvironment environment = new PhysicalEnvironment(); // Create a View and attach the Canvas3D and the physical // body and environment to the view. view1 = new View(); view1.addCanvas3D(c1); view1.addCanvas3D(c2); view1.addCanvas3D(c3); view1.addCanvas3D(c4); view1.setPhysicalBody(body); view1.setPhysicalEnvironment(environment); // Create a BranchGroup node for the view platform BranchGroup vpRoot = new BranchGroup(); // Create a ViewPlatform object, and its associated // TransformGroup object, and attach it to the root of the // subgraph. Attach the view to the view platform. Transform3D t = new Transform3D(); t.set(new Vector3f(0.0f, 0.0f, 2.0f)); ViewPlatform vp = new ViewPlatform(); vpTrans1 = new TransformGroup(t); vpTrans1.addChild(vp); vpRoot.addChild(vpTrans1); vpRoot.addChild(scene); view1.attachViewPlatform(vp); // Attach the branch graph to the universe, via the // Locale. The scene graph is now live! locale.addBranchGraph(vpRoot); } }

Read the article

C++ Multithreading with pthread is blocking (including sockets)

- by Sebastian Büttner

I am trying to implement a multi threaded application with pthread. I did implement a thread class which looks like the following and I call it later twice (or even more), but it seems to block instead of execute the threads parallel. Here is what I got until now: The Thread Class is an abstract class which has the abstract method "exec" which should contain the thread code in a derive class (I did a sample of this, named DerivedThread) Thread.hpp #ifndef THREAD_H_ #define THREAD_H_ #include <pthread.h> class Thread { public: Thread(); void start(); void join(); virtual int exec() = 0; int exit_code(); private: static void* thread_router(void* arg); void exec_thread(); pthread_t pth_; int code_; }; #endif /* THREAD_H_ */ And Thread.cpp #include <iostream> #include "Thread.hpp" /*****************************/ using namespace std; Thread::Thread(): code_(0) { cout << "[Thread] Init" << endl; } void Thread::start() { cout << "[Thread] Created Thread" << endl; pthread_create( &pth_, NULL, Thread::thread_router, reinterpret_cast<void*>(this)); } void Thread::join() { cout << "[Thread] Join Thread" << endl; pthread_join(pth_, NULL); } int Thread::exit_code() { return code_; } void Thread::exec_thread() { cout << "[Thread] Execute" << endl; code_ = exec(); } void* Thread::thread_router(void* arg) { cout << "[Thread] exec_thread function in thread" << endl; reinterpret_cast<Thread*>(arg)->exec_thread(); return NULL; } DerivedThread.hpp #include "Thread.hpp" class DerivedThread : public Thread { public: DerivedThread(); virtual ~DerivedThread(); int exec(); void Close() = 0; DerivedThread.cpp [...] #include "DerivedThread.cpp" [...] int DerivedThread::exec() { //code to be executed do { cout << "Thread executed" << endl; usleep(1000000); } while (true); //dummy, just to let it run for a while } [...] Basically, I am calling this like the here: DerivedThread *thread; cout << "Creating Thread" << endl; thread = new DerivedThread(); cout << "Created thread, starting..." << endl; thread->start(); cout << "Started thread" << endl; cout << "Creating 2nd Thread" << endl; thread = new DerivedThread(); cout << "Created 2nd thread, starting..." << endl; thread->start(); cout << "Started 2nd thread" << endl; What is working great if I am only starting one of these Threads , but if I start multiple which should run together (not synced, only parallel) . But I discovered, that the thread is created, then as it tries to execute it (via start) the problem seems to block until the thread has closed. After that the next Thread is processed. I thought that pthread would do it unblocked for me, so what did I wrong? A sample output might be: Creating Thread [Thread] Thread Init Created thread, starting... [Thread] Created thread [Thread] exec_thread function in thread [Thread] Execute Thread executed Thread executed Thread executed Thread executed Thread executed Thread executed Thread executed .... Until Thread 1 is not terminated, a Thread 2 won't be created not executed. The process above is executed in an other class. Just for the information: I am trying to create a multi threaded server. The concept is like this: MultiThreadedServer Class has a main loop, like this one: ::inet::ServerSock *sock; //just a simple self made wrapper class for sockets DerivedThread *thread; for (;;) { sock = new ::inet::ServerSock(); this->Socket->accept( *sock ); cout << "Creating Thread" << endl; //Threads (according to code sample above) thread = new DerivedThread(sock); //I did not mentoine the parameter before as it was not neccesary, in fact, I pass the socket handle with the connected socket to the thread cout << "Created thread, starting..." << endl; thread->start(); cout << "Started thread" << endl; } So I thought that this would loop over and over and wait for new connections to accept. and when a new client arrives, I am creating a new thread and give the thread the connected socket as a parameter. In the DerivedThread::exec I am doing the handling for the connected client. Like: [...] do { [...] if (this-sock_-read( Buffer, sizeof(PacketStruc) ) 0) { cout << "[Handler_Base] Recv Packet" << endl; //handle the packet } else { Connected = false; } delete Buffer; } while ( Connected ); So I loop in the created thread as long as the client keeps the connection. I think, that the socket may cause the blocking behaviour. Edit: I figured out, that it is not the read() loop in the DerivedThread Class as I simply replaced it with a loop over a simple cout-usleep part. It did also only execute the first one and after first thread finished, the 2nd one was executed. Many thanks and best regards, Sebastian

Read the article

C++ simple logging class with UTF-8 output [code example]

- by Andrew

Hello everyone, I was working on one of my academic projects and for the first time I needed pure C++ without GUI. After googling for a while, I did not find any simple and easy to use implementation for logging and created my own. This is a simple implementation with iostreams that logs messages to screen and to the file simultaneously. I was thinking of using templates but then I realized that I do not expect any changes and removed that. It is modified std::wostream with two added modifiers: 1. TimeStamp - prints time-stamp 2. LogMode(LogModes) - switches output: file only, screen only, file+screen. *Boost::utf8_codecvt_facet* is used for UTF-8 output. // ############################################################################ // # Name: MyLog.h # // # Purpose: Logging Class Header # // # Author: Andrew Drach # // # Modified by: <somebody> # // # Created: 03/21/10 # // # SVN-ID: $Id$ # // # Copyright: (c) 2010 Andrew Drach # // # Licence: <license> # // ############################################################################ #ifndef INCLUDED_MYLOG_H #define INCLUDED_MYLOG_H // headers -------------------------------------------------------------------- #include <string> #include <iostream> #include <fstream> #include <exception> #include <boost/program_options/detail/utf8_codecvt_facet.hpp> using namespace std; // definitions ---------------------------------------------------------------- // ---------------------------------------------------------------------------- // DblBuf class // Splits up output stream into two // Inspired by http://wordaligned.org/articles/cpp-streambufs // ---------------------------------------------------------------------------- class DblBuf : public wstreambuf { private: // private member declarations DblBuf(); wstreambuf *bf1; wstreambuf *bf2; virtual int_type overflow(int_type ch) { int_type eof = traits_type::eof(); int_type not_eof = !eof; if ( traits_type::eq_int_type(ch,eof) ) return not_eof; else { char_type ch1 = traits_type::to_char_type(ch); int_type r1( bf1on ? bf1->sputc(ch1) : not_eof ); int_type r2( bf2on ? bf2->sputc(ch1) : not_eof ); return (traits_type::eq_int_type(r1,eof) || traits_type::eq_int_type(r2,eof) ) ? eof : ch; } } virtual int sync() { int r1( bf1on ? bf1->pubsync() : NULL ); int r2( bf2on ? bf2->pubsync() : NULL ); return (r1 == 0 && r2 == 0) ? 0 : -1; } public: // public member declarations explicit DblBuf(wstreambuf *bf1, wstreambuf *bf2) : bf1(bf1), bf2(bf2) { if (bf1) bf1on = true; else bf1on = false; if (bf2) bf2on = true; else bf2on = false; } bool bf1on; bool bf2on; }; // ---------------------------------------------------------------------------- // logstream class // Wrapper for a standard wostream with access to modified buffer // ---------------------------------------------------------------------------- class logstream : public wostream { private: // private member declarations logstream(); public: // public member declarations DblBuf *buf; explicit logstream(wstreambuf *StrBuf, bool isStd = false) : wostream(StrBuf, isStd), buf((DblBuf*)StrBuf) {} }; // ---------------------------------------------------------------------------- // Logging mode Class // ---------------------------------------------------------------------------- enum LogModes{LogToFile=1, LogToScreen, LogToBoth}; class LogMode { private: // private member declarations LogMode(); short mode; public: // public member declarations LogMode(short mode1) : mode(mode1) {} logstream& operator()(logstream &stream1) { switch(mode) { case LogToFile: stream1.buf->bf1on = true; stream1.buf->bf2on = false; break; case LogToScreen: stream1.buf->bf1on = false; stream1.buf->bf2on = true; break; case LogToBoth: stream1.buf->bf1on = true; stream1.buf->bf2on = true; } return stream1; } }; logstream& operator<<(logstream &out, LogMode mode) { return mode(out); } wostream& TimeStamp1(wostream &out1) { time_t time1; struct tm timeinfo; wchar_t timestr[512]; // Get current time and convert it to a string time(&time1); localtime_s (&timeinfo, &time1); wcsftime(timestr, 512,L"[%Y-%b-%d %H:%M:%S %p] ",&timeinfo); return out1 << timestr; } // ---------------------------------------------------------------------------- // MyLog class // Logs events to both file and screen // ---------------------------------------------------------------------------- class MyLog { private: // private member declarations MyLog(); auto_ptr<DblBuf> buf; string mErrorMsg1; string mErrorMsg2; string mErrorMsg3; string mErrorMsg4; public: // public member declarations explicit MyLog(string FileName1, wostream *ScrLog1, locale utf8locale1); ~MyLog(); void NewEvent(wstring str1, bool TimeStamp = true); string FileName; wostream *ScrLog; wofstream File; auto_ptr<logstream> Log; locale utf8locale; }; // ---------------------------------------------------------------------------- // MyLog constructor // ---------------------------------------------------------------------------- MyLog::MyLog(string FileName1, wostream *ScrLog1, locale utf8locale1) : // ctors mErrorMsg1("Failed to open file for application logging! []"), mErrorMsg2("Failed to write BOM! []"), mErrorMsg3("Failed to write to file! []"), mErrorMsg4("Failed to close file! []"), FileName(FileName1), ScrLog(ScrLog1), utf8locale(utf8locale1), File(FileName1.c_str()) { // Adjust error strings mErrorMsg1.insert(mErrorMsg1.length()-1,FileName1); mErrorMsg2.insert(mErrorMsg2.length()-1,FileName1); mErrorMsg3.insert(mErrorMsg3.length()-1,FileName1); mErrorMsg4.insert(mErrorMsg4.length()-1,FileName1); // check for file open errors if ( !File ) throw ofstream::failure(mErrorMsg1); // write UTF-8 BOM File << wchar_t(0xEF) << wchar_t(0xBB) << wchar_t(0xBF); // switch locale to UTF-8 File.imbue(utf8locale); // check for write errors if ( File.bad() ) throw ofstream::failure(mErrorMsg2); buf.reset( new DblBuf(File.rdbuf(),ScrLog->rdbuf()) ); Log.reset( new logstream(&*buf) ); } // ---------------------------------------------------------------------------- // MyLog destructor // ---------------------------------------------------------------------------- MyLog::~MyLog() { *Log << TimeStamp1 << "Log finished." << endl; // clean up objects Log.reset(); buf.reset(); File.close(); // check for file close errors if ( File.bad() ) throw ofstream::failure(mErrorMsg4); } //--------------------------------------------------------------------------- #endif // INCLUDED_MYLOG_H Tested on MSVC 2008, boost 1.42. I do not know if this is the right place to share it. Hope it helps anybody. Feel free to make it better.

Read the article

MVC4 Model in View has nested data - cannot get data in model

- by Taersious

I have a Model defined that gets me a View with a list of RadioButtons, per IEnumerable. Within that Model, I want to display a list of checkboxes that will vary based on the item selected. Finally, there will be a Textarea in the same view once the user has selected from the available checkboxes, with some dynamic text there based on the CheckBoxes that are selected. What we should end up with is a Table-per-hierarchy. The layout is such that the RadioButtonList is in the first table cell, the CheckBoxList is in the middle table cell, and the Textarea is ini the right table cell. If anyone can guide me to what my model-view should be to achieve this result, I'll be most pleased... Here are my codes: // // View Model for implementing radio button list public class RadioButtonViewModel { // objects public List<RadioButtonItem> RadioButtonList { get; set; } public string SelectedRadioButton { get; set; } } // // Object for handling each radio button public class RadioButtonItem { // this object public string Name { get; set; } public bool Selected { get; set; } public int ObjectId { get; set; } // columns public virtual IEnumerable<CheckBoxItem> CheckBoxItems { get; set; } } // // Object for handling each checkbox public class CheckBoxViewModel { public List<CheckBoxItem> CheckBoxList { get; set; } } // // Object for handling each check box public class CheckBoxItem { public string Name { get; set; } public bool Selected { get; set; } public int ObjectId { get; set; } public virtual RadioButtonItem RadioButtonItem { get; set; } } and the view @model IEnumerable<EF_Utility.Models.RadioButtonItem> @{ ViewBag.Title = "Connect"; ViewBag.Selected = Request["name"] != null ? Request["name"].ToString() : ""; } @using (Html.BeginForm("Objects" , "Home", FormMethod.Post) ){ @Html.ValidationSummary(true) <table> <tbody> <tr> <td style="border: 1px solid grey; vertical-align:top;"> <table> <tbody> <tr> <th style="text-align:left; width: 50px;">Select</th> <th style="text-align:left;">View or Table Name</th> </tr> @{ foreach (EF_Utility.Models.RadioButtonItem item in @Model ) { <tr> <td> @Html.RadioButton("RadioButtonViewModel.SelectedRadioButton", item.Name, ViewBag.Selected == item.Name ? true : item.Selected, new { @onclick = "this.form.action='/Home/Connect?name=" + item.Name + "'; this.form.submit(); " }) </td> <td> @Html.DisplayFor(i => item.Name) </td> </tr> } } </tbody> </table> </td> <td style="border: 1px solid grey; width: 220px; vertical-align:top; @(ViewBag.Selected == "" ? "display:none;" : "")"> <table> <tbody> <tr> <th>Column </th> </tr> <tr> <td> </td> </tr> </tbody> </table> </td> <td style="border: 1px solid grey; vertical-align:top; @(ViewBag.Selected == "" ? "display:none;" : "")"> <textarea name="output" id="output" rows="24" cols="48"></textarea> </td> </tr> </tbody> </table> } and the relevant controller public ActionResult Connect() { /* TEST SESSION FIRST*/ if( Session["connstr"] == null) return RedirectToAction("Index"); else { ViewBag.Message = ""; ViewBag.ConnectionString = Server.UrlDecode( Session["connstr"].ToString() ); ViewBag.Server = ParseConnectionString( ViewBag.ConnectionString, "Data Source" ); ViewBag.Database = ParseConnectionString( ViewBag.ConnectionString, "Initial Catalog" ); using( var db = new SysDbContext(ViewBag.ConnectionString)) { var objects = db.Set<SqlObject>().ToArray(); var model = objects .Select( o => new RadioButtonItem { Name = o.Name, Selected = false, ObjectId = o.Object_Id, CheckBoxItems = Enumerable.Empty<EF_Utility.Models.CheckBoxItem>() } ) .OrderBy( rb => rb.Name ); return View( model ); } } } What I am missing it seems, is the code in my Connect() method that will bring the data context forward; at that point, it should be fairly straight-forward to set up the Html for the View. EDIT ** So I am going to need to bind the RadioButtonItem to the view with something like the following, except my CheckBoxList will NOT be an empty set. // // POST: /Home/Connect/ [HttpPost] public ActionResult Connect( RadioButtonItem rbl ) { /* TEST SESSION FIRST*/ if ( Session["connstr"] == null ) return RedirectToAction( "Index" ); else { ViewBag.Message = ""; ViewBag.ConnectionString = Server.UrlDecode( Session["connstr"].ToString() ); ViewBag.Server = ParseConnectionString( ViewBag.ConnectionString, "Data Source" ); ViewBag.Database = ParseConnectionString( ViewBag.ConnectionString, "Initial Catalog" ); using ( var db = new SysDbContext( ViewBag.ConnectionString ) ) { var objects = db.Set<SqlObject>().ToArray(); var model = objects .Select( o => new RadioButtonItem { Name = o.Name, Selected = false, ObjectId = o.Object_Id, CheckBoxItems = Enumerable.Empty<EF_Utility.Models.CheckBoxItem>() } ) .OrderBy( rb => rb.Name ); return View( model ); } } }

Read the article

Using Supermicro IPMI behind a Proxy?

- by Stefan Lasiewski

This is a SuperMicro server with a X8DT3 motherboard which contains an On-board IPMI BMC. In this case, the BMC is a Winbond WPCM450). I believe many Dell servers use this a similar BMC model. A common practice with IPMI is to isolated it to a private, non-routable network. In our case all IPMI cards are plugged into a private management LAN at 192.168.1.0/24 which has no route to the outside world. If I plug my laptop into the 192.168.1.0/24 network, I can verify that all IPMI features work as expected, including the remote console. I need to access all of the IPMI features from a different network, over some sort of encrypted connection. I tried SSH port forwarding. This works fine for a few servers, however, we have close to 100 of these servers and maintaining a SSH client configuration to forward 6 ports on 100 servers is impractical. So I thought I would try a SOCKS proxy. This works, but it seems that the Remote Console application does not obey my systemwide proxy settings. I setup a SOCKS proxy. Verbose logging allows me to see network activity, and if ports are being forwarded. ssh -v -D 3333 [email protected] I configure my system to use the SOCKS proxy. I confirm that Java is using the SOCKS proxy settings. The SOCKS proxy is working. I connect to the BMC at http://192.168.1.100/ using my webbrowser. I can log in, view the Server Health, power the machine on or off, etc. Since SSH verbose logging is enabled, I can see the progress. Here's where it get's tricky: I click on the "Launch Console" button which downloads a file called jviewer.jnlp. JNLP files are opened with Java Web Start. A Java window opens. The titlebar says says "Redirection Viewer" in the title bar. There are menus for "Video" "Keyboard" "Mouse", etc. This confirms that Java is able to download the application through the proxy, and start the application. 60 seconds later, the application times out and simply says "Error opening video socket". Here's a screenshot. If this worked, I would see a VNC-style window. My SSH logs show no connection attempts to ports 5900/5901. This suggests that the Java application started the VNC application, but that the VNC application ignores the systemwide proxy settings and is thus unable to connect to the remote host. Java seems to obey my systemwide proxy settings, but this VNC application seems to ignore it. Is there any way for me to force this VNC application to use my systemwide proxy settings?

Read the article

Can't clone gitosis-admin.git local from my snow leopard server running gitosis

- by joggink

I've installed gitosis as described here: http://gist.github.com/264304 One of the things that I had to adjust was to give my git user permissions to use ssh (which I did trough server admin - access - ssh and added the 'git' user). When I ssh from my local machine (mac osx) as the git user, I get this response: PTY allocation request failed on channel 0 bash: gitosis-serve: command not found Connection to 10.0.0.108 closed. Which I think is normal, because in Pro GIT the author says you should get something like this if you try ssh'ing to the server using your git user: PTY allocation request failed on channel 0 fatal: unrecognized command 'gitosis-serve schacon@quaternion' Connection to gitserver closed. So far so good, I think? Now when I try to clone my gitosis-admin.git repository using this command: $git clone [email protected]:gitosis-admin.git I get this: Initialized empty Git repository in /Users/joggink/gitosis-admin/.git/ bash: gitosis-serve: command not found fatal: The remote end hung up unexpectedly So after doing some searching, I found an answer here on serverfault claiming I should use ssh:// as protocol for my git clone (which I thought is the default git protocol?) However, when I try: $git clone ssh://[email protected]:gitosis-admin.git This is the response: The authenticity of host ' (::1)' can't be established. RSA key fingerprint is 80:4d:77:c7:78:cb:c9:42:e3:82:06:7c:fe:c0:08:ce. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '' (RSA) to the list of known hosts. Password: Password: Password: Permission denied (publickey,keyboard-interactive). fatal: The remote end hung up unexpectedly When I type in my own password (because my git user has no password), I get following error: The authenticity of host ' (::1)' can't be established. RSA key fingerprint is 80:4d:77:c7:78:cb:c9:42:e3:82:06:7c:fe:c0:08:ce. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '' (RSA) to the list of known hosts. Password: bash: git-upload-pack: command not found fatal: The remote end hung up unexpectedly I added my upload-pack location as followed: $git clone -u /usr/local/git/bin/git-upload-pack ssh://[email protected]:gitosis-admin.git I get the error that gitosis-admin.git isn't a git repo... Initialized empty Git repository in /Users/joggink/gitosis-admin/.git/ The authenticity of host ' (::1)' can't be established. RSA key fingerprint is 80:4d:77:c7:78:cb:c9:42:e3:82:06:7c:fe:c0:08:ce. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '' (RSA) to the list of known hosts. Password: fatal: '[email protected]:gitosis-admin.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly I've been searching for a solution for almost a week now, and every topic I've found on the internet gives no result...

Read the article

Firefox 3.5.6 causes entire computer to freeze

- by Anthony Aziz

Here's the situation: Environment: Just installed a fresh copy of Win7 Pro 32-bit to NTFS partition on 750GB SATA drive Hardware: E8400 3GHz ASUS P5QL Pro 4GB DDR2 1066 RAM EVGA 9800 GTX+ Plenty of cooling, no problems with hardware before Data is stored on a separate partition, including My Documents No security software is yet installed No extensions installed yet Problem: While using Firefox, sometimes the entire computer will freeze/hang. I get no mouse or keyboard input, can't CTRL+ALT+DEL, no "not responding" indication, just a static image on my display. My drivers are all up to date as far as I'm aware (I just installed this copy of Windows last week). I first noticed this when trying to install Xmarks. I went to the Xmarks site and tried to install and it would freeze. I managed to get it installed (Safe mode and the Mozilla addon site worked), but when I go to configure it (log in, etc), the computer freezes. I don't think it's a matter of usage time or memory issues, because while testing, I browsed wallpaper galleries for about 30 minutes, sometimes as many as 12-15 tabs open at a time, without issue. Sometimes I won't even try to install Xmarks at it will hang. I can install (some) other extensions, the only one I've tried is download status bar (which works). What I've done to try to fix: Restarted (duh) Windows safe mode Completely remove Firefox and install it to a new directory, according to Mozilla's KB (I haven't tried the profile manager, though I assume this does the same thing, except perhaps more thoroughly) Some BIOS changes, including Power options, disabling oveclocking (it was a modest overclock on the CPU, which has run Win7 beta and RC for almost a year now) Memtest Used another Windows user profile, same tragic results I'm STUCK now, with no idea what to do. I'm using Chrome as my main browser at the moment, but that's not something I want to be stuck with. I like Firefox and want to use it. I'm going to try creating a new profile first. One thing I did notice: I started leaving task manager and performance monitor open when anticipating (but dreading) a freeze. firefox.exe had low CPU and low memory, but it looked like overall disk usage was seeing some spikes on the small graph Performance Monitor gives you. I saw on one blog post a fellow using XP moved his Local Settings directory from a separate drive to his main drive, and that solved it, but I don't think my AppData directory is on my D: drive, and that's on the same physical device anyways. Still, something that might be worth trying. I'd extremely appreciate any help. Thanks very much. I really don't want to reinstall Windows from scratch again :( Anthony Aziz

Read the article

How to reinstall OEM Windows 98 SE?

- by Sammy

I'm trying to install Windows 98 SE on an old PC and it's not going well. I run into this problem. Searching for Boot Record from Floppy..OK Starting Windows 98... TOSHIBA Enhanced-IDE CD/DVD-ROM Device Driver (ATAPI) Version 2.24 (C)Copyright Toshiba Corp. 1995-1999. All rights reserved. Device Name : TOSCD001 Number of units : 1 MSCDEX Version 2.25 Copyright (C) MIcrosoft Corp. 1986-1995. All rights reserved. Drive Z: = Driver TOSCD001 unit 0 TOSHIBA MACHINE Invalid drive specification Path not found - C:\TOOLS\CDROMDRV.SYS Invalid drive specification Invalid drive specification After that last line, it leaves me at a bitmap image displaying instructions to reboot with Ctrl+Alt+Del. It doesn't say why I have to reboot, and it doesn't state any error type, it just want's me to reboot for no apparent reason. After reboot, it just boots up from Floppy again and it cycles through the same thing all over again. The computer has been restored to original specification. Original system recovery "CD-ROM" discs are available and they are not scratched or anything, they are in very good condition. It's a set of 3 CDs, and the first disc labeled "1/3" should be the one holding the OEM version of Windows 98 SE. There is also a boot disk for Windows 98. I'm not sure what the other two discs are for. This computer came with three language support, so those could be holding different language versions or additional OEM discs. But I'm quite sure that the first disc holds the main operating system. BIOS has been set to optimized defaults. Boot priority is as follows; Floppy, IDE-0, CD-ROM. Under Standard CMOS settings, BIOS scans and autoconfigures both the hard drive and the CD/DVD drive. On POST it finds them both, and it finds the DOS bootdisk and starts preparing for installation, as you can see above. So what's this "invalid drive specification" about? Why isn't the installation starting? Updates Update 1 Booting from CD disc 2 In desperation I tried booting from the second CD. Boot order was; Floppy, CD-ROM, IDE-0. It boots normally from floppy disk, just like above, but then returns following. File not found - Z:\3LNGINST\TOOLS\PARTINFO.TXT I accidentally pressed some key on the keyboard, and before I knew it, the following screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Verifying drive integrity, 16% complete. After completion another screen showed up. Create Primary DOS Partition Current fixed disk drive: 1 Do you wish to use the maximum available size for a Primary DOS Partition and make the partition active (Y/N)?....................? [Y] Verifying drive integrity, 7% complete. I didn't choose Yes, it was set automatically. After completion the computer was automatically rebooted. Then I got a new screen. This is in Norwegian/Swedish/Finnish. Here's the message in Swedish. Hårddisken är inte klar för återställning av programvara. Installationsprogrammet måste skapa nya partitioner (C:, D:, ...). VARNING! ALLT INNEHÅLL PÅ HÅRDDISKEN KOMMER ATT RADERAS! Tryck på en tangent om du vill fortsätta (eller CTRL-C för att avbryta). Let me translate that. Hard drive is not ready for restoring the software. Setup program has to create new partitions (C:, D:, ...). WARNING! ALL CONTENTS ON THE HARD DRIVE WILL BE ERASED! Press any key to continue (or CTRL-C to cancel). I pressed Enter and it started formatting the hard drive. WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE c: WILL BE LOST! Proceed with Format (Y/N)?y Formatting 14,67.53M 1 percent completed. It automatically sets the "y" option and starts formatting. Rebooting with CD disc 1 After completing this operation it rebooted automatically. I inserted CD disc 1 and there was no issue with "invalid drive specification" anymore. Instead, a bitmap menu was displayed where it asked me to choose a language. And I thought I had it there for a while but it didn't work out. After choosing the language, another menu was displayed asking me to choose a type of recovery (restore pre-installed software OR restore hard drive partitions and pre-installed software). I opted for the second option. Then a data destruction warning showed up where I just pressed 1 to Continue. It did something and then just rebooted and the same formatting screen shows up as before. So something is not right. Am I doing it wrong? I seem to have come past the CD-ROM driver issue at least. But now I'm stuck with this problem... it seems to have something to do with the hard drive. Like... why is is it always trying to format it? Isn't it enough to format it once? By the way, it needs to be formatted as FAT32, right? Windows 98 doesn't support NTFS? I think FDISK should have taken care of this already. I know this is an old hard drive, but I connected to my main computer and it was able to read and write to it without a problem. It does have bad sectors though, but it's expected on an old hard drive like this. Any ideas?.. Update 2 I seem to be repeatedly getting stuck at the format screen where it asks to press any key to continue. So tried to cancel it this time with Ctrl+C. This leaves me at: A:\TOOLS> I can do DIR and CD and I tried to change to Z: drive. I tried running "setup" but there is no such thing. Z:\>setup Bad command or file name Update 3 Floppy structure Here's the file/folder structure of the floppy disk. A:\>dir /s Volume in drive A has no label. Volume Serial Number is 1700-1069 Directory of A:\ 1999-10-11 10:44 <DIR> BMP 1998-05-11 22:01 93 880 COMMAND.COM 1999-10-11 10:44 <DIR> factory 1999-10-11 10:44 <DIR> lang 1999-10-11 10:44 <DIR> TOOLS 2000-05-19 15:32 339 CONFIG.SYS 1999-10-26 13:38 0 BOOTLOG.TXT 2000-06-08 08:32 3 691 AUTOEXEC.BAT 4 File(s) 97 910 bytes Directory of A:\BMP 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 0 File(s) 0 bytes Directory of A:\factory 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 2000-06-08 13:09 2 662 3LNGINSF.BAT 1 File(s) 2 662 bytes Directory of A:\lang 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-11-24 08:02 49 575 FORMAT.COM 1998-11-24 08:02 63 900 FDISK.EXE 2 File(s) 113 475 bytes Directory of A:\TOOLS 1999-10-11 10:44 <DIR> . 1999-10-11 10:44 <DIR> .. 1998-05-06 22:01 49 575 FORMAT.COM 1995-10-27 20:29 28 164 BMPVIEW.EXE 1999-01-26 15:54 15 MAKEPA32.TXT 1998-05-06 22:01 3 878 XCOPY.EXE 1998-05-06 22:01 41 472 XCOPY32.MOD 1998-05-06 22:01 33 191 HIMEM.SYS 1998-05-06 22:01 125 495 EMM386.EXE 1998-05-06 22:01 18 967 SYS.COM 1996-01-31 21:55 18 CLK.COM 1994-04-02 08:20 22 HARDBOOT.COM 1999-02-03 15:46 15 MAKEPA16.TXT 1999-04-14 16:36 7 840 PARTFO32.EXE 2000-05-19 15:01 1 169 PARTFORM.BAT 1996-10-02 01:47 1 642 MBRCLR.COM 1999-07-01 11:58 8 175 BIOSCHKN.EXE 1998-06-23 08:55 5 904 PAR-TYPE.EXE 1998-11-24 08:02 29 271 MODE.COM 1998-11-24 08:02 15 252 ATTRIB.EXE 1998-11-24 08:02 19 083 DELTREE.EXE 1999-04-21 15:01 23 304 NTBB.EXE 1997-05-07 14:19 1 SYS.TXT 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-11 20:01 34 566 KEYBOARD.SYS 1998-05-11 20:01 19 927 KEYB.COM 1999-10-26 14:31 910 partinfo.txt 1998-06-16 15:58 5 936 CHKDRVAC.EXE 1998-05-06 22:01 63 900 FDISK.EXE 1998-05-06 22:01 45 379 SMARTDRV.EXE 1992-12-03 19:48 10 695 SCISET.EXE 1997-06-25 15:49 6 YENT 1998-05-06 22:01 25 473 MSCDEX.EXE 1998-05-06 22:01 5 239 CHOICE.COM 1997-07-18 17:41 6 876 MBR.COM 1997-07-01 15:01 6 545 CHK2GB.COM 1998-06-10 20:04 8 128 PARTFORM.EXE 1990-01-04 02:09 19 MAKEPAR2.TXT 1990-01-04 01:00 27 MAKEPAR3.TXT 1990-01-04 01:00 27 MAKEPAR4.TXT 1998-02-13 13:47 15 MAKEPART.TXT 1999-04-14 13:47 5 200 DISKSIZE.EXE 1999-05-06 14:56 7 856 PARTFO16.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 42 File(s) 734 463 bytes Total Files Listed: 49 File(s) 948 510 bytes 12 Dir(s) 268 800 bytes free A:\> CONFIG.SYS contents Here's the content of CONFIG.SYS. DEVICE=A:\TOOLS\HIMEM.SYS /TESTMEM:OFF REM I=B000-B7ff for Desktop BIOSes rem DEVICE=A:\TOOLS\EMM386.EXE NOEMS I=B000-B7ff x=C000-D000 DEVICE=A:\TOOLS\EMM386.EXE NOEMS x=C000-D000 DEVICE=A:\TOOLS\CDROMDRV.SYS /D:TOSCD001 BUFFERS=10 FILES=69 DOS=HIGH,UMB STACKS=9,256 LASTDRIVE=Z SWITCHES=/F SHELL=A:\COMMAND.COM /P /E:2048 AUTOEXEC.BAT contents :BEGIN @ECHO OFF PATH=A:\;A:\TOOLS; MSCDEX /D:TOSCD001 /L:Z /M:10 smartdrv 1024 128 SET TOOLS=A:\TOOLS SET COMSPEC=A:\COMMAND.COM SET EXITDRIVE=C: SET EXITPATH=\ CALL Z:\SETENV.BAT > NUL :TOSHCHK BIOSChkN IF NOT ERRORLEVEL 1 goto C_ACCESS BMPVIEW Z:\3LNGINST\BMP\NO_TOSP3.bmp /X=120 /Y=80 PAUSE > NUL SET EXITDRIVE=A: GOTO END :C_ACCESS CALL PARTFORM.BAT :C_EMPTY IF EXIST C:\*.* GOTO C_NOTEMPTY call z:\setenv.bat>nul goto PREPDU :C_NOTEMPTY REM ------------------MENU------------------------ :STARTMENU CLS BMPVIEW Z:\3LNGINST\BMP\LANGSELC.BMP /X=120 /Y=120 CLK CHOICE /C:123 /N >NUL REM L is the language that is selected IF ERRORLEVEL 1 SET L=%LNG1% IF ERRORLEVEL 2 SET L=%LNG2% IF ERRORLEVEL 3 SET L=%LNG3% SET BMP=BMP%L% BMPVIEW Z:\3LNGINST\%bmp%\HDDMENU.BMP /X=72 /Y=82 CLK CHOICE /C:129F /N > NUL IF ERRORLEVEL 4 GOTO FACTORY_MENU IF ERRORLEVEL 3 GOTO EXIT_MENU IF ERRORLEVEL 2 GOTO PARTFORM_MENU IF ERRORLEVEL 1 GOTO FORMAT_MENU GOTO END :FACTORY_MENU BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMATF GOTO END :EXIT_MENU BMPVIEW Z:\3LNGINST\%bmp%\9.bmp /XC /X=96 /Y=267 choice /C:1pause /T:1,01 >nul SET EXITDRIVE=A: SET EXITPATH=\lang cls mode mono rem keyb xx>nul cls GOTO END :PARTFORM_MENU BMPVIEW Z:\3LNGINST\%bmp%\2.bmp /XC /X=96 /Y=216 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\partform.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO PART_FORM SET EXITDRIVE=A: GOTO END :FORMAT_MENU BMPVIEW Z:\3LNGINST\%bmp%\1.bmp /XC /X=96 /Y=165 choice /C:1pause /T:1,01 >nul BMPVIEW Z:\3LNGINST\%bmp%\qformat.bmp /X=120 /Y=140 CLK choice /c:12 /N >nul IF ERRORLEVEL 2 GOTO STARTMENU IF ERRORLEVEL 1 GOTO FORMAT SET EXITDRIVE=A: GOTO END REM ------------------ MENU END ------------------------ :FORMAT bmpview Z:\3LNGINST\%bmp%\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul CLS IF (%QFORMAT%)==(NO) GOTO FULLFO FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU :FULLFO FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU :FORMATF CLS IF (%QFORMAT%)==(NO) GOTO FULLFO_F FORMAT C: /Q /V:"" <A:\TOOLS\YENT >NUL call z:\setenv.bat>nul goto PREPDU_F :FULLFO_F FORMAT C: /V:"" <A:\TOOLS\YENT call z:\setenv.bat>nul goto PREPDU_F :PART_FORM bmpview Z:\3LNGINST\bmp\1.bmp /XC /X=145 /Y=235 choice /C:1pause /T:1,01 >nul MBR /! HARDBOOT REM ====================== Triple Select ====================== :PREPDU XCOPY z:\3LNGINST\*.* C:\*.* /E /S /V >NUL ATTRIB -H -R -S C:\TOOLS\CDROMDRV.SYS COPY A:\TOOLS\CDROMDRV.SYS C:\TOOLS /Y SYS C: >NUL goto REBOOT :PREPDU_F copy A:\TOOLS\SMARTDRV.EXE C:\ /Y ATTRIB -H -R -S C:\SMARTDRV.EXE copy A:\FACTORY\3LNGINSF.bat c:\ c:\3LNGINSF.bat cls REM ====================== Dual Select END ====================== REM --------------- END ------------------ :REBOOT SMARTDRV.EXE /C bmpview Z:\3LNGINST\BMP\reboot3.bmp /X=120 /Y=140 :FOREVER pause >nul goto FOREVER :END SMARTDRV.EXE /C %EXITDRIVE% cd %EXITPATH% echo on CD structure S:\>dir /s Volume in drive S is T3ELK4SC Volume Serial Number is 2042-5BC9 Directory of S:\ 2000-08-22 14:14 <DIR> 3LNGINSF 2000-08-22 14:14 <DIR> 3LNGINST 2000-06-15 15:57 <DIR> CRC 2000-06-15 12:04 387 667 767 T310C1NO.W98 2000-09-07 15:36 273 setenv.BAT 2 File(s) 387 668 040 bytes Directory of S:\3LNGINSF 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-10-27 10:51 1 806 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-05-19 15:29 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 2 071 bytes Directory of S:\3LNGINSF\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 12 File(s) 626 416 bytes Directory of S:\3LNGINSF\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINSF\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-07-06 14:49 3 593 3LNGINST.BAT 1998-11-24 08:02 15 252 ATTRIB.EXE 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-11-24 08:02 19 083 DELTREE.EXE 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 20 File(s) 490 603 bytes Directory of S:\3LNGINSF\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\3LNGINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1999-05-31 09:51 1 576 AUTOEXEC.BAT 2000-08-22 14:14 <DIR> BMP 2000-08-22 14:14 <DIR> Bmpfin 2000-08-22 14:14 <DIR> Bmpnor 2000-08-22 14:14 <DIR> Bmpswe 2000-05-19 15:30 265 CONFIG.SYS 2000-08-22 14:14 <DIR> POSTINST 2000-08-22 14:14 <DIR> TOOLS 2000-08-22 14:14 <DIR> WIN98SYS 2 File(s) 1 841 bytes Directory of S:\3LNGINST\BMP 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1999-01-04 02:38 718 3.BMP 2000-07-05 11:22 60 118 Cdchg2.bmp 2000-07-05 11:22 60 118 Cdchg3.bmp 2000-07-05 13:37 60 118 Fin.bmp 2000-07-06 14:18 120 118 Menu.bmp 2000-07-05 13:34 60 118 Nor.bmp 2000-07-05 11:53 35 318 Progress.bmp 2000-07-06 14:08 40 518 Reboot3.bmp 2000-07-05 13:40 60 118 Swe.bmp 2000-07-05 12:09 84 118 Wrongcd2.bmp 2000-07-05 12:09 84 118 Wrongcd3.bmp 2000-07-05 13:52 48 118 langselc.bmp 2000-07-05 11:47 57 318 no_tosp3.bmp 15 File(s) 772 370 bytes Directory of S:\3LNGINST\Bmpfin 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 2000-03-08 15:02 78 486 Hddmenu.bmp 2000-03-08 15:31 25 318 No_tospc.bmp 2000-03-08 15:37 36 518 PARTFORM.BMP 2000-03-08 15:42 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpnor 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-05 13:26 78 486 Hddmenu.bmp 1998-07-13 11:36 25 318 No_tospc.bmp 1998-07-13 11:41 36 518 PARTFORM.BMP 1998-07-13 11:45 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\Bmpswe 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1997-04-22 09:43 718 1.BMP 1997-04-22 09:44 718 2.BMP 1998-06-13 00:07 718 9.bmp 1999-05-06 08:14 78 486 Hddmenu.bmp 1998-07-10 16:25 25 318 No_tospc.bmp 1998-07-10 16:29 36 518 PARTFORM.BMP 1998-07-10 17:08 36 518 Qformat.bmp 7 File(s) 178 994 bytes Directory of S:\3LNGINST\POSTINST 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 09:15 33 POSTINST.BAT 1 File(s) 33 bytes Directory of S:\3LNGINST\TOOLS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-05-19 14:52 3 898 3LNGINST.BAT 1995-10-27 18:29 28 164 BMPVIEW.EXE 1999-01-13 11:13 13 720 CDROMDRV.SYS 1998-05-06 20:01 5 239 CHOICE.COM 1996-01-31 19:55 18 CLK.COM 1998-05-06 20:01 125 495 EMM386.EXE 1999-07-01 12:23 61 566 F3DCHK.EXE 1998-05-06 20:01 49 575 FORMAT.COM 1994-04-02 06:20 22 HARDBOOT.COM 1998-05-06 20:01 33 191 HIMEM.SYS 1998-05-06 20:01 25 473 MSCDEX.EXE 2000-07-06 14:41 910 PARTINFO.TXT 1998-05-06 20:01 12 663 RAMDRIVE.SYS 1998-05-06 20:01 45 379 SMARTDRV.EXE 1997-05-07 14:19 1 SYS.TXT 1995-09-27 14:25 6 813 VOLCHECK.EXE 1998-05-06 20:01 3 878 XCOPY.EXE 1998-05-06 20:01 41 472 XCOPY32.MOD 1997-06-25 13:49 6 YENT 19 File(s) 457 483 bytes Directory of S:\3LNGINST\WIN98SYS 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 1998-12-04 20:00 222 390 IO.SYS 1998-05-06 20:01 18 967 SYS.COM 1998-05-06 20:01 93 880 command.com 3 File(s) 335 237 bytes Directory of S:\CRC 1601-01-01 02:00 <DIR> . 1601-01-01 02:00 <DIR> .. 2000-06-15 12:07 181 422 T310C1NO.ALL 2000-06-15 12:09 215 427 T310C1NO.CRC 2000-06-15 12:07 2 157 T310C1NO.HID 3 File(s) 399 006 bytes Total Files Listed: 104 File(s) 391 625 352 bytes 42 Dir(s) 0 bytes free S:\> Now which line or lines need to be changed? Do I really have to change drive letter Z: to C:? Proposed solutions Solution #1 Ramhound proposed to change the boot order to following; CD-ROM, IDE-0, Floppy This didn't help. In fact, here is the result of it. Searching for Boot Record from CDROM..Not Found Searching for Boot Record from IDE-0.. OK Missing operating system Any other ideas?... Solution #2 Rik proposed to run Z:\setup. Now that I have found a way to drop to DOS prompt with Ctrl+C as described above (Update 2), I did try running setup but there is no such command or file in there. So that didn't work.

Read the article

Setting up two screens in Xorg

- by viraptor

I'be got two Nvidia cards, but Xorg activates only one of them. The following config is based on the nvidia configurator output: Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" LeftOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Module" Load "dbe" Load "extmod" Load "type1" Load "freetype" Load "glx" EndSection Section "InputDevice" Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" Identifier "Keyboard0" Driver "keyboard" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "HP LE2201w" HorizSync 24.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" ModelName "Acer AL2017" HorizSync 30.0 - 82.0 VertRefresh 56.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Card0" Driver "nvidia" VendorName "nVidia Corporation" BoardName "GeForce 6100 nForce 405" BusID "PCI:0:13:0" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nVidia Corporation" BoardName "GeForce 8400 GS" BusID "PCI:2:0:0" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection What I see in the log file is: (==) Log file: "/var/log/Xorg.0.log", Time: Fri Mar 19 11:08:08 2010 (==) Using config file: "/etc/X11/xorg.conf" (==) ServerLayout "Layout0" (**) |-->Screen "Screen0" (0) (**) | |-->Monitor "Monitor0" (==) No device specified for screen "Screen0". Using the first device section listed. (**) | |-->Device "Card0" (**) |-->Screen "Screen1" (1) (**) | |-->Monitor "Monitor1" (==) No device specified for screen "Screen1". Using the first device section listed. (**) | |-->Device "Card0" (**) |-->Input Device "Keyboard0" (**) |-->Input Device "Mouse0" (**) Option "Xinerama" "0" (==) Automatically adding devices (==) Automatically enabling devices even though later on both cards are detected: (--) PCI:*(0:0:13:0) 10de:03d1:1019:2601 nVidia Corporation C61 [GeForce 6100 nForce 405] rev 162, Mem @ 0xfb000000/16777216, 0xd0000000/268435456, 0xfc000000/16777216, BIOS @ 0x????????/131072 (--) PCI: (0:2:0:0) 10de:0422:0000:0000 nVidia Corporation G86 [GeForce 8400 GS] rev 161, Mem @ 0xf8000000/16777216, 0xe0000000/268435456, 0xf6000000/33554432, I/O @ 0x0000bc00/128, BIOS @ 0x????????/131072 [ --- some more logs --- ] (II) Mar 19 11:08:10 NVIDIA(0): NVIDIA GPU GeForce 6100 nForce 405 (C61) at PCI:0:13:0 (II) Mar 19 11:08:10 NVIDIA(0): (GPU-0) [ --- some more logs --- ] (II) Mar 19 11:08:12 NVIDIA(GPU-1): NVIDIA GPU GeForce 8400 GS (G86) at PCI:2:0:0 (GPU-1) Unfortunately later on only one card is initialised and one screen is active. Xrandr shows only one screen too. Any ideas on how to fix it?

Read the article

Solaris10 x86 mirror. Making second disk booteable when failure

- by Kani

Did a mirror (RAID1) with Solaris 10 in x86. Everything OK. Now, I´m trying to make the second disk booteable, this is: from grub or in case of failure of disk1. I edited /boot/grub/menu.lst: #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris 10 9/10 s10x_u9wos_14a X86 findroot (rootfs1,0,a) kernel /platform/i86pc/multiboot module /platform/i86pc/boot_archive #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot -s module /boot/amd64/x86.miniroot-safe #---------------------END BOOTADM-------------------- #---------- ADDED BY BOOTADM - DO NOT EDIT ---------- title Solaris failsafe findroot (rootfs1,0,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe #---------------------END BOOTADM-------------------- #Make second disk booteable!!!!!!! title alternate boot findroot (rootfs1,1,a) kernel /boot/multiboot kernel/unix -s module /boot/x86.miniroot-safe But is not working. In the BIOS, when I select "alternate boot" I get: Error 15: 15 file not found also, how to configure to GRUB to make the disk2 to boot in case of error in disk1? Additionally, I did (but not related to GRUB): eeprom altbootpath=/devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a Here is the output of some commands that may help you: /sbin/biosdev 0x80 /pci@0,0/pci108e,5352@1f,2/disk@0,0 0x81 /pci@0,0/pci108e,5352@1f,2/disk@1,0 ls -l /dev/dsk/c1t?d0s0 lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t0d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@0,0:a lrwxrwxrwx 1 root root 50 Jul 7 12:01 /dev/dsk/c1t1d0s0 -> ../../devices/pci@0,0/pci108e,5352@1f,2/disk@1,0:a more /boot/solaris/bootenv.rc setprop ata-dma-enabled '1' setprop atapi-cd-dma-enabled '0' setprop ttyb-rts-dtr-off 'false' setprop ttyb-ignore-cd 'true' setprop ttya-rts-dtr-off 'false' setprop ttya-ignore-cd 'true' setprop ttyb-mode '9600,8,n,1,-' setprop ttya-mode '9600,8,n,1,-' setprop lba-access-ok '1' setprop prealloc-chunk-size '0x2000' setprop bootpath '/pci@0,0/pci108e,5352@1f,2/disk@0,0:a' setprop keyboard-layout 'US-English' setprop console 'text' setprop altbootpath '/pci@0,0/pci108e,5352@1f,2/disk@1,0:a' cat /etc/vfstab #device device mount FS fsck mount mount #to mount to fsck point type pass at boot options # fd - /dev/fd fd - no - /proc - /proc proc - no - #/dev/dsk/c1t0d0s1 - - swap - no - /dev/md/dsk/d1 - - swap - no - /dev/md/dsk/d0 /dev/md/rdsk/d0 / ufs 1 no - /devices - /devices devfs - no - sharefs - /etc/dfs/sharetab sharefs - no - ctfs - /system/contract ctfs - no - objfs - /system/object objfs - no - swap - /tmp tmpfs - yes - df -h Filesystem size used avail capacity Mounted on /dev/md/dsk/d0 909G 11G 889G 2% / /devices 0K 0K 0K 0% /devices ctfs 0K 0K 0K 0% /system/contract proc 0K 0K 0K 0% /proc mnttab 0K 0K 0K 0% /etc/mnttab swap 14G 972K 14G 1% /etc/svc/volatile objfs 0K 0K 0K 0% /system/object sharefs 0K 0K 0K 0% /etc/dfs/sharetab /usr/lib/libc/libc_hwcap1.so.1 909G 11G 889G 2% /lib/libc.so.1 fd 0K 0K 0K 0% /dev/fd swap 14G 40K 14G 1% /tmp swap 14G 28K 14G 1% /var/run

Read the article

What are some fast methods for navigating to frequently used folders in Windows 7?

- by fostandy

(This is a followup question from my previous question.) In windows XP I used to be able to quickly navigate to frequently used folders by making use of the 'Favorites' menu item and the hotkey behaviour. In certain conditions it could be set up so that getting to a particular folder was as easy as alt-a x (and without a file explorer window open it was as fast as win-e alt-a x). I am struggling to get anywhere near this speed in Windows 7 and would like to solicit advice from others regarding fast folder navigation to see if I am missing any methods. My current way to navigate quickly is basically move hand to mouse move cursor to navigation pane/pain. scroll all the way to the top (because normally I the panel is focused on whatever deep directory structure I am already in). sift through my 50+ favorites to get the one I want, or click a link to a folder that contains further links in some sort of 'pseudo-tree' functionality. select it. This is slower than my previous method by upwards of an order of magnitude. There are a couple of things I've contemplated: add expandable folders, not just direct links, to the favorites menu. add expandable folders, not just direct links, to the start menu. add links of my favorite folders to a submenu of the start menu so that they come up when I search them. They do but this still rather cumbersome started using 7stacks - url here (I cannot link the url directly due to lack of reputation but http://www.alastria.com/index.php?p=software-7s). This is about the closest I've gotten to some sort of compact, customizeable, easy to access, tree based navigation structure. How do you power users quickly navigate to your favorite folders? Are there keyboard shortcuts I am missing? Can someone recommend other apps or addon or extensions that can achieve this sort of functionality? The Current solution (thanks to the answers below) I am going to use is a combination of Autohotkey and 7stacks - autohotkey to launch 7stacks, 7stacks with the 'menu' stack type for fast, key-enabled navigation to folders organised in a tree structure. This solves about 90% of the issue, the only issues are (note that these are really minor, I am really splitting hairs more than anything here) Can't use this for existing folder navigation (ie already have a explorer window open, want to go to another directory) A bit more cumbersome to add/remove entries to compared to xp favorites. A little slower than xp favorites. Whatever. I'm happy. Thanks guys. I think the answer is a split to John T and Kelbizzle - I've elected to give the answer to John T and +1 to Kelbizzle as I had already mentioned 7stacks.

Read the article

SSSD Authentication

- by user24089

I just built a test server running OpenSuSE 12.1 and am trying to learn how configure sssd, but am not sure where to begin to look for why my config cannot allow me to authenticate. server:/etc/sssd # cat sssd.conf [sssd] config_file_version = 2 reconnection_retries = 3 sbus_timeout = 30 services = nss,pam domains = test.local [nss] filter_groups = root filter_users = root reconnection_retries = 3 [pam] reconnection_retries = 3 # Section created by YaST [domain/mose.cc] access_provider = ldap ldap_uri = ldap://server.test.local ldap_search_base = dc=test,dc=local ldap_schema = rfc2307bis id_provider = ldap ldap_user_uuid = entryuuid ldap_group_uuid = entryuuid ldap_id_use_start_tls = True enumerate = False cache_credentials = True chpass_provider = krb5 auth_provider = krb5 krb5_realm = TEST.LOCAL krb5_kdcip = server.test.local server:/etc # cat ldap.conf base dc=test,dc=local bind_policy soft pam_lookup_policy yes pam_password exop nss_initgroups_ignoreusers root,ldap nss_schema rfc2307bis nss_map_attribute uniqueMember member ssl start_tls uri ldap://server.test.local ldap_version 3 pam_filter objectClass=posixAccount server:/etc # cat nsswitch.conf passwd: compat sss group: files sss hosts: files dns networks: files dns services: files protocols: files rpc: files ethers: files netmasks: files netgroup: files publickey: files bootparams: files automount: files ldap aliases: files shadow: compat server:/etc # cat krb5.conf [libdefaults] default_realm = TEST.LOCAL clockskew = 300 [realms] TEST.LOCAL = { kdc = server.test.local admin_server = server.test.local database_module = ldap default_domain = test.local } [logging] kdc = FILE:/var/log/krb5/krb5kdc.log admin_server = FILE:/var/log/krb5/kadmind.log default = SYSLOG:NOTICE:DAEMON [dbmodules] ldap = { db_library = kldap ldap_kerberos_container_dn = cn=krbContainer,dc=test,dc=local ldap_kdc_dn = cn=Administrator,dc=test,dc=local ldap_kadmind_dn = cn=Administrator,dc=test,dc=local ldap_service_password_file = /etc/openldap/ldap-pw ldap_servers = ldaps://server.test.local } [domain_realm] .test.local = TEST.LOCAL [appdefaults] pam = { ticket_lifetime = 1d renew_lifetime = 1d forwardable = true proxiable = false minimum_uid = 1 clockskew = 300 external = sshd use_shmem = sshd } If I log onto the server as root I can su into an ldap user, however if I try to console locally or ssh remotely I am unable to authenticate. getent doesn't show the ldap entries for users, Im not sure if I need to look at LDAP, nsswitch, or what: server:~ # ssh localhost -l test Password: Password: Password: Permission denied (publickey,keyboard-interactive). server:~ # su test test@server:/etc> id uid=1000(test) gid=100(users) groups=100(users) server:~ # tail /var/log/messages Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): system info: [Client not found in Kerberos database] Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): authentication failure; logname=LOGIN uid=0 euid=0 tty=/dev/ttyS1 ruser= rhost= user=test Nov 24 09:36:44 server login[14508]: pam_sss(login:auth): received for user test: 4 (System error) Nov 24 09:36:44 server login[14508]: FAILED LOGIN SESSION FROM /dev/ttyS1 FOR test, System error server:~ # vi /etc/pam.d/common-auth auth required pam_env.so auth sufficient pam_unix2.so auth required pam_sss.so use_first_pass server:~ # vi /etc/pam.d/sshd auth requisite pam_nologin.so auth include common-auth account requisite pam_nologin.so account include common-account password include common-password session required pam_loginuid.so session include common-session session optional pam_lastlog.so silent noupdate showfailed

Read the article

Customizing Fantacy Remote .INI file

- by karthik

I am using Fantacy Remote to remote view other machines. I have attached the default .INI file that Fantacy Remote uses. When i connect to a machine, the client user should not have mouse and keyboard access of the Remote machine. It should be a View only remote connection. And i want to make the Remote viewer screen to be in full screen mode, because i dont want the user to do anything with menubars of Fatancy remote. Because this is kiosk application. What should i change in configuration file [.ini] inorder to achieve the above ? Anyone who have used this software before, kindly help.. [APP] iVersion= 101 pcVersion=1.01a pcBuildDate=Mar 27 2009 [MAIN] iFirstSetup= 0 rcMain.rcLeft= 676 rcMain.rcTop= 378 rcMain.rcRight= 1004 rcMain.rcBottom= 672 iShowLog= 0 iMode= 1 [GENERAL] iTips= 1 iTrayAnimation= 1 iCheckColor= 1 iPriority= 1 iSsememcpy= 1 iAutoOpenRecv= 1 pcRecvPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\recv pcFileName=FantasyRemote iLanguage= 1 [SERVER] iAcceptVideo= 1 iAcceptAudio= 1 iAcceptInput= 1 iAutoAccept= 1 iAutoTray= 0 iConnectSound= 1 iEnablePassword= 0 pcPassword= pcPort=7902 [CLIENT] iAutoConnect= 0 pcPassword= pcDefaultPort=7902 [NETWORK] pcConnectAddr=192.168.1.1 pcPort=7902 [VIDEO] iEnable= 1 pcFcc=AMV3 pcFccServer= pcDiscription= pcDiscriptionServer= iFps= 30 iMouse= 2 iHalfsize= 0 iCapturblt= 0 iShared= 0 iSharedTime= 5 iVsync= 1 iCodecSendState= 1 iCompress= 2 pcPlugin= iPluginScan= 0 iPluginAspectW= 16 iPluginAspectH= 9 iPluginMouse= 1 iActiveClient= 0 iDesktop1= 1 iDesktop2= 2 iDesktop3= 0 iDesktop4= 3 iScan= 1 iFixW= 16 iFixH= 8 [AUDIO] iEnable= 1 iFps= 30 iVolume= 6 iRecDevice= 0 iPlayDevice= 0 pcSamplesPerSec=44100Hz pcChannels=2ch:Stereo pcBitsPerSample=16bit iRecBuffNum= 150 iPlayBuffNum= 4 [INPUT] iEnable= 1 iFps= 30 iMoe= 0 iAtlTab= 1 [MENU] iAlwaysOnTop= 0 iWindowMode= 0 iFrameSize= 4 iSnap= 1 [HOTKEY] iEnable= 1 key_IDM_HELP=0x00000070 mod_IDM_HELP=0x00000000 key_IDM_ALWAYSONTOP=0x00000071 mod_IDM_ALWAYSONTOP=0x00000000 key_IDM_CONNECT=0x00000072 mod_IDM_CONNECT=0x00000000 key_IDM_DISCONNECT=0x00000073 mod_IDM_DISCONNECT=0x00000000 key_IDM_CONFIG=0x00000000 mod_IDM_CONFIG=0x00000000 key_IDM_CODEC_SELECT=0x00000000 mod_IDM_CODEC_SELECT=0x00000000 key_IDM_CODEC_CONFIG=0x00000000 mod_IDM_CODEC_CONFIG=0x00000000 key_IDM_SIZE_50=0x00000074 mod_IDM_SIZE_50=0x00000000 key_IDM_SIZE_100=0x00000075 mod_IDM_SIZE_100=0x00000000 key_IDM_SIZE_200=0x00000076 mod_IDM_SIZE_200=0x00000000 key_IDM_SIZE_300=0x00000000 mod_IDM_SIZE_300=0x00000000 key_IDM_SIZE_400=0x00000000 mod_IDM_SIZE_400=0x00000000 key_IDM_CAPTUREWINDOW=0x00000077 mod_IDM_CAPTUREWINDOW=0x00000004 key_IDM_REGION=0x00000077 mod_IDM_REGION=0x00000000 key_IDM_DESKTOP1=0x00000078 mod_IDM_DESKTOP1=0x00000000 key_IDM_ACTIVE_MENU=0x00000079 mod_IDM_ACTIVE_MENU=0x00000000 key_IDM_PLUGIN=0x0000007A mod_IDM_PLUGIN=0x00000000 key_IDM_PLUGIN_SCAN=0x00000000 mod_IDM_PLUGIN_SCAN=0x00000000 key_IDM_DESKTOP2=0x00000078 mod_IDM_DESKTOP2=0x00000004 key_IDM_DESKTOP3=0x00000079 mod_IDM_DESKTOP3=0x00000004 key_IDM_DESKTOP4=0x0000007A mod_IDM_DESKTOP4=0x00000004 key_IDM_WINDOW_NORMAL=0x0000000D mod_IDM_WINDOW_NORMAL=0x00000004 key_IDM_WINDOW_NOFRAME=0x0000000D mod_IDM_WINDOW_NOFRAME=0x00000002 key_IDM_WINDOW_FULLSCREEN=0x0000000D mod_IDM_WINDOW_FULLSCREEN=0x00000001 key_IDM_MINIMIZE=0x00000000 mod_IDM_MINIMIZE=0x00000000 key_IDM_MAXIMIZE=0x00000000 mod_IDM_MAXIMIZE=0x00000000 key_IDM_REC_START=0x00000000 mod_IDM_REC_START=0x00000000 key_IDM_REC_STOP=0x00000000 mod_IDM_REC_STOP=0x00000000 key_IDM_SCREENSHOT=0x0000002C mod_IDM_SCREENSHOT=0x00000002 key_IDM_AUDIO_MUTE=0x00000073 mod_IDM_AUDIO_MUTE=0x00000004 key_IDM_AUDIO_VOLUME_DOWN=0x00000074 mod_IDM_AUDIO_VOLUME_DOWN=0x00000004 key_IDM_AUDIO_VOLUME_UP=0x00000075 mod_IDM_AUDIO_VOLUME_UP=0x00000004 key_IDM_CTRLALTDEL=0x00000023 mod_IDM_CTRLALTDEL=0x00000003 key_IDM_QUIT=0x00000000 mod_IDM_QUIT=0x00000000 key_IDM_MENU=0x0000007B mod_IDM_MENU=0x00000000 [OVERLAY] iIndicator= 1 iAlphaBlt= 1 iEnterHide= 0 pcFont=MS UI Gothic [AVI] iSound= 1 iFileSizeLimit= 100000 iPool= 4 iBuffSize= 32 iStartDiskSpaceCheck= 1 iStartDiskSpace= 1000 iRecDiskSpaceCheck= 1 iRecDiskSpace= 100 iCache= 0 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\avi [SCREENSHOT] iSound= 1 iAutoOpen= 1 pcPath=C:\Documents and Settings\karthikeyan\My Documents\Downloads\fremote101a\FantasyRemote101a\ss pcPlugin=BMP [CDLG_SERVER] mrcWnd.rcLeft= 667 mrcWnd.rcTop= 415 mrcWnd.rcRight= 1013 mrcWnd.rcBottom= 634 [CWND_CLIENT] miShowLog= 0 m_iOverlayLock= 0

Read the article

Blank displays after inactivity, mouse cursor not showing up

- by Mike Christiansen

I have a Windows 7 Enterprise x86 machine that is exhibiting some strange problems. After some inactivity (it varies how long it takes), when I come back to my computer, both of my monitors are black. The monitors are on, with a black display. Moving the mouse and pressing keys on the keyboard do not work. This happens at least once a day. When I first encountered the issue, I performed a hard shutdown and restarted the computer. About 10% of the time when I did this, the resolutions on my monitors were messed up. The native resolution on the primary monitor is 1600x900, and the native on my secondary is 1440x900. None of the widescreen resolutions would be present in the display properties. I had 800x600, 1024x768, and 1280x1024. As a workaround to this issue, I've found that if I plug in my secondary monitor as the primary monitor, and leave the secondary unplugged, then Windows will start in 1024x768 on the secondary. Then, I can use Windows 7's "Detect" feature and it finds the 1440x900 resolution, and sets it. Then I have to connect the primary monitor to the secondary port and set it as the primary. Then I can switch the two cables, putting the primary into the primary, the secondary into the secondary. Then use the "Detect" feature again, and it finds the correct resolutions. Some time after performing the above, I discovered that when the screens were blanked, I could simply press "Control+Alt+Delete", type in my password, and everything comes up fine - except my mouse cursor. All applications and features work as intended, except there is no mouse cursor (the mouse actually works though...). I have the "Show location of pointer when I press CTRL key" option selected, so I can press CTRL and use my mouse as normal - but I have no actual cursor. When the computer is in this state, UAC is also not functional. Whenever a UAC prompt appears, the screens go black (the original symptoms) and I have to press Escape to exit UAC. Because of the above symptoms (the UAC black screen thing, etc) I beleive winlogon.exe may be the culprit. However, I have no idea how to fix it. I am unable to restart winlogon.exe due to the problems I am having with winlogon.exe (the UAC black screen) Looking for any ideas.... More information Windows 7 x86 Enterprise Domain environment (I have a secondary account with administrator rights) Dell Optiplex 960 Cannot perform "optional" windows updates due to an activation issue (I am testing a windows 7 image, and an activation infrastructure has not been created yet. However, this issue was happening before I was unable to perform windows update, and windows was up to date at the time Updated video card driver (as an attempt to fixing the resolution issue) Disabled all power saving options Please let me know what else you need to help me solve this issue! Thanks in advance, Mike

Read the article

Suspend only works once after full power cycle with ASUS P7P55D-E Pro

- by John Chadwick

This one is strange. I can't seem to get suspend working more than once per power cycle. When I say "power cycle," I mean the only way to get one proper suspend is to cut power from the power supply and boot back up cold. After the proper suspend, I get a failed suspend, and after all reboots or cold boots until power is cut, suspends fail. I'm using an ASUS P7P55D-E Pro with a Sandy Bridge Core i7, running on Ubuntu Precise repositories and UEFI. I'm running Nouveau from repository (And Gallium3d compiled from git, but that does not come into this since I can avoid OpenGL and it still happens the same way) with a GTX 285 (nv50.) I had to build a custom kernel (3.3) in order for ACPI 5.0 to be supported and make suspend work at all. I compiled it using the latest Ubuntu kernel's config file with the additional entries set to the default options. All packages are up to date. I know these are relatively exotic settings, but I'm hoping maybe I can get some help anyways. The behavior when suspend fails is strange. Upon a proper suspend, all fans turn off and the only led left on, the power led, is blinking. Upon a failed suspend, 1. USB power remains. 2. The power led stays on solid. 3. All fans seem to still be on. 4. I can hear what I believe is the primary harddrive shutting off. 5. Despite USB power remaining, the USB powered keyboard does not respond to anything, and the indicator leds on it shut off. Pressing the power button does nothing, and of course I have not to date found a way to wake it up. When trouble shooting the first round of issues I got with suspend not too long ago, I ended up building a list of modules to disable upon sleeping. Here's my config file for them: In /etc/pm/config.d/01modules: SUSPEND_MODULES="uhci_hd ehci_hd button" All of my other pm configuration files are stock. In case it's any help, here are my relevant BIOS settings. Thanks.

Read the article

Is Steam for Mac effectively running as superuser?

- by godDLL

When you download the client it does not weigh too much, and seems to do very little. Inside the app bundle there is a script that—upon inspecting the environment and deciding you're not running Linux—launches the client, which downloads the full support environment and resources. For this to happen (all of this is saved inside the bundle, the app bundle gets updated in this process) Steam wants Universal Access for Assistive Devices, and your password. Cacheable resources, preferences (like keyboard shortcuts), support files (like game hardware requirement lookup tables) live inside the bundle, not in ~/Library/{Application Support|Preferences|Cache}; games' data get dumped into ~/Documents/Steam Content. I'd describe myself as a bit OCD (which really says a lot), and I wouldn't care that much still. I'd go comb this hairy mess and find out where stuff is, when and if I need to, even if it's in an unfamiliar place; that does not actually tick me off. Well, a little bit. What makes me concerned is the way Steam needs both Access for Assistive Devices, and my password to run. The former gives it the ability to talk very intimately with running apps and the underlying system; while the latter (admin account) could very well give it and it's publishers unrestricted access to all my software, hardware and data. With publishers like Rockstar using scene NOCD cracks to publish their games on Steam, I'm not so sure I'm OK with this. I'd like more games made available for the MacOS X and all the pretty machines that run it, but this arrangement does not seem very Mac-like to me. It looks like Valve is going around system security measures and best practices, foregoing sandboxing, code signing, relatively sane structured organization; all the things that would appeal to someone who's no fun at parties at all, and will die alone, in his long dead mother's basement… wait. Right. Anyway. Can we get some input on Steam for Mac security at the end-user machine, from someone who understands how Accessibility API works, whether games distributed on Steam can read and write outside the user homefolder, collect data from other running apps, or similar?

Read the article

Windows Setup could not configure Windows to run on this computer's hardware

- by Hello71

The whole installation goes smoothly up to the point of "Completing installation ...". The monitor changes resolution, after which a standard dialog box pops up saying Windows Setup could not configure Windows to run on this computer's hardware Then, in a few seconds, the whole machine powers down. Trying to restart produces the message: STOP: c000021a {Fatal System Error} 0x00000000 (0xc0000001 0x00100448) OR it boots into Setup and comes up with the message: Windows Setup encountered an unexpected error... (This is not the actual error, just paraphrasing) I tried using the OEM restore instead of a regular install, but it fails with the same error. (Even though it worked before...) General specs: HP Pavilion Elite e9262f Intel Core i5-750 Processor ATI Radeon HD 4650 Hitachi HDT721010SLA360 ATA Device 6GB DDR3 RAM SuperMulti DVD Burner with LightScribe Some built-in Wi-Fi module http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01916917 I've tried disconnecting the wireless card and disabling the built-in Ethernet and Firewire via the BIOS, and replacing the wireless keyboard and mouse with wired USB ones. Didn't work. I've also tried changing the SATA controller settings in the BIOS to RAID, AHCI, and IDE, reinstalling each time I changed. Still not working. I think the reason why it is showing the Fatal System Error is because it didn't finish installing before it errored out and shut down, so the system is left in an inconsistent state. I've tried 3 different copies (including the OEM restore) of Windows 7 now, and they're all failing at the same point, with the same error message. I've tried to install Windows 7 maybe 10 times already, with the exact same error message at the exact same location. Hm... Interestingly, the 32-bit version of Windows 7 works, but the 64-bit version doesn't. Perhaps it was a badly burned disk? Reburning the 64-bit version still comes up with the same error. Here's a picture of the side of the case that clearly says it came with Windows 7 64-bit, along with the model number and CPU. sudo fdisk -l: Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0009896f Device Boot Start End Blocks Id System /dev/sda1 * 1 13 104391 7 HPFS/NTFS /dev/sda2 14 94119 755906445 7 HPFS/NTFS /dev/sda3 119922 121602 13492224 7 HPFS/NTFS /dev/sda4 94120 119922 207257740+ 5 Extended /dev/sda5 119527 119922 3170769 82 Linux swap / Solaris /dev/sda6 107174 119526 99225441 83 Linux /dev/sda7 94120 107173 104856192 7 HPFS/NTFS Partition table entries are not in disk order

Read the article

NX Client for Windows 7 Opens Remote Desktop in Multiple Windows

- by Corey Kennedy

What I'm trying to do: access my Ubuntu desktop remotely via NX Client on my Windows 7 laptop. My environment: server: Ubuntu 10.10 on AMD 1Ghz/512MB RAM PC client: Windows 7 on ThinkPad sl510 Software: server is running NXServer 3.4.0. Using xfce4 window manager. Laptop is using NXClient for Windows In my NX Client "Desktop" settings I've selected "Unix" and "Custom" for OS and environment. I've also specified "startxfce4" as the application to launch when NX connects. I am able to authenticate an NX session on my laptop. By this I mean, I can start the client on my laptop, enter credentials for my Linux user, and NX establishes a connection to the server and attempts to open a remote desktop window. The problem, though, is that this remote desktop is "fragmented" into many Windows. One window will display the bulk of my desktop (complete with desktop icons for "Home," "File System," and "Trash") while another window will contain the taskbar, and another window will contain the application strip. I can select each of these Windows individually, but I cannot click on any objects within them. I've searched Super User, Ubuntu Forums, NX help, Server Fault, and tried many Google searches - none have turned up another case of this particular problem. I'm stumped. Does anyone have any suggestions for what I might try? I'm guessing the problem has to do with my xfce config files, but I've only just setup this server - it's been a long time since I've used Linux and there's a lot I just don't know. What I am NOT trying to do: use Desktop sharing from Ubuntu, whereby I VNC into a desktop that I've already established on the server. I am trying to configure this Linux box as a headless server that I can stash someplace out-of-the-way in my house, then interact with through my laptop. I don't want to have a monitor or keyboard connected to the Linux box. Thanks for your help! edit: 1/19/2011 Well, this is truly bizarre. To my knowledge I've made no changes to either system - the laptop or the server. But today after starting up the server for the first time in a few days, and making sure that nxserver was running, I was able to connect with the nxclient from my laptop with no problems. I have a full desktop in a single window and I am able to interact with it normally. This is really weird, but the problem seems to be resolved.

Read the article

IE8 Refuses to run Javascript from Local Hard Drive

- by Josh Stodola

I have a problem that just started at work recently and the network manager is certain he did not change anything with the group policy. Anyways, here is a detailed description of the problem. My machine is Windows XP SP3, and I use IE8 to browse. We have McAffee anti-virus software that I am unable to configure. I use the following file to test... <!DOCTYPE html> <html> <head> <title>Javascript Test</title> </head> <body> <script type="text/javascript"> document.write("<h1>PASS</h1>"); </script> <noscript> <h1>FAIL</h1> </noscript> </body> </html> When I open this file from the C: drive, it fails every time. If I execute it anywhere else (local/remote web server or on a mapped network drive), it works just fine. When I am simply browsing the Internet, Javascript on web sites works just fine. It is only failing on files running from my C: drive. Additionally, I have had a couple other programmers in the department try this file on their C: drive, and it works fine for them. So I don't believe it is a group policy thing. I need to fix this because I do extensive testing from my C: drive, and I am accustomed to doing so. I don't want to get into the habit of moving files to a different drive just to test. Things I have tried: Enabled "Allow Active Content to Run Files on My Computer" in Options | Advanced | Security Enabled "Allow Active Scripting" in Options | Security | Custom Level Verified that "Script" was not checked as disabled in Developer Toolbar Added localhost to Trusted Sites in Options Disabled McAffee completely (momentarily, with help from network admin) Used an older DOCTYPE in my test HTML page Re-installed IE8 completely Ran regsvr32 on the JScript.dll Slammed keyboard I am sure that there is a setting somewhere that will fix this problem, possibly in the registry. I would not be surprised if it was related to the developer toolbar. At this point I do not know where else to look. Can anyone help me resolve this problem? EDIT: Regardless of the bounty, this issue is still ongoing.

Read the article

amd gpu but display on intel integrated graphics

- by pitseeker

On my Ubuntu 12.04 I connected my monitor to the onboard intel graphics. I'd like to use my ati radeon 6770 for opencl tasks (e.g. bitcoin mining). So far I couldn't figure out how to get the ati driver working. When calling "aticonfig --initial -f" it always writes a new xorg.conf that ignores the intel graphics. At boot time it works only when I attached the monitor to the ati card. So I manually tampered with the xorg.conf and got this: Section "ServerLayout" Identifier "Default Monitor" Screen 0 "myscreen" 0 0 Screen 1 "deadscreen" RightOf "myscreen" EndSection Section "Module" EndSection Section "Monitor" Identifier "Default Monitor" Option "VendorName" "Monitor Vendor" Option "ModelName" "Monitor Name" Option "DPMS" "true" EndSection Section "Monitor" Identifier "null Monitor" Option "Enable" "false" EndSection Section "Device" Identifier "Intel Integrated Graphics" Driver "intel" BusID "PCI:0:2:0" Screen 0 EndSection Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" Screen 1 EndSection Section "Screen" Identifier "myscreen" Device "Intel Integrated Graphics" Monitor "Default Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection Section "Screen" Identifier "deadscreen" Device "aticonfig-Device[0]-0" Monitor "null Monitor" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 EndSubSection EndSection I think this might be the right way since I see that X tries to start both drivers in /var/log/Xorg.0.log. However the fglrx driver seems crash (end of xorg.0.log): Backtrace: [ 6.625] 0: /usr/bin/X (xorg_backtrace+0x26) [0x7fb5cd41b846] [ 6.625] 1: /usr/bin/X (0x7fb5cd293000+0x18c6ea) [0x7fb5cd41f6ea] [ 6.625] 2: /lib/x86_64-linux-gnu/libpthread.so.0 (0x7fb5cc5b9000+0xfcb0) [0x7fb5cc5c8cb0] [ 6.625] 3: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (xdl_xs111_atiddxGetGPUMapInfo+0x1b1) [0x7fb5c88e16b1] [ 6.625] 4: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/drivers/fglrx_drv.so (atiddxGetGPUMapInfo+0xd) [0x7fb5c87bcc0d] [ 6.625] 5: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ab29) [0x7fb5ca147b29] [ 6.625] 6: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1cf8c) [0x7fb5ca149f8c] [ 6.625] 7: /usr/lib/x86_64-linux-gnu/xorg/extra-modules/extra-modules.dpkg-tmp/modules/extensions/libglx.so (0x7fb5ca12d000+0x1ee55) [0x7fb5ca14be55] [ 6.626] 8: /usr/bin/X (InitExtensions+0x99) [0x7fb5cd350069] [ 6.626] 9: /usr/bin/X (0x7fb5cd293000+0x3d605) [0x7fb5cd2d0605] [ 6.626] 10: /lib/x86_64-linux-gnu/libc.so.6 (__libc_start_main+0xed) [0x7fb5cb44e76d] [ 6.626] 11: /usr/bin/X (0x7fb5cd293000+0x3daad) [0x7fb5cd2d0aad] [ 6.626] Segmentation fault at address 0x14 [ 6.626] Caught signal 11 (Segmentation fault). Server aborting [ 6.626] I'd be very happy if someone can give me a hint on how to configure my ATI card while using the integrated graphics for display. Update I used most of jjhughes57 config and successfully booted the X server on intel (keyboard layout is changed though, funnily). Unfortunately the 2nd X server (fglrx) doesn't fully start. It shuts itself down right after starting [ 6.265] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments [ 6.296] (II) UnloadModule: "mouse" [ 6.296] (II) Unloading mouse [ 6.296] (II) UnloadModule: "kbd" [ 6.296] (II) Unloading kbd [ 6.298] (II) fglrx(0): Shutdown CMMQS [ 6.298] (II) fglrx(0): [uki] removed 1 reserved context for kernel [ 6.298] (II) fglrx(0): [uki] unmapping 8192 bytes of SAREA 0x2000 at 0x7fbef8209000 [ 6.337] (II) fglrx(0): Interrupt handler Shutdown. [ 6.470] ddxSigGiveUp: Closing log [ 6.470] Server terminated successfully (0). Closing log file. Thanks for any hints what is wrong here.

Read the article

UPS vs Solar Power in case of power failure for a server [on hold]

- by Zen 8000k

I am looking for a low power, low end pc able to run 24/7 without overheating and a way to support it in case of power failure. Power failures can be up to 72 hours. The pc dosen't need a monitor or keyboard. A modem must also be protected in case of power failure. When i say low end, i don't mean crap. The cpu needs to be x86 and have at least 1k cpu in this chart: http://www.cpubenchmark.net/index.php What's the best way to do this? EDIT: more info. I need to run a home server. The server will perform light tasks mainly. A x86 cpu sadly is the only route for my use. I want to be able to run the server and the router/modem in case of power failure. Now, regarding how long the power will fail: 1) 1 hours is OK for most situations. (say 90%) 2) 3 hours is OK (say 98%) 3) 6 hours is more thank OK. (say 99.5%) 4) On extreme cases the power might fail days. I believe this is very unlikely to happen. More is great but, really, how ofter power will fail more than 3 hours? I believe once every year at best. Well, that's too rare to care about. Given the above, I am looking for a cost effective way to archive 1-3 hour power or 6 hour if possible. Solutions: You guys give me great ideas. 1) Power generator: no good as power will fail for 10 seconds before returning. Also I read online, "clean" power generators cost 1.5k+, so it's out of budged. Non clean generator might damage electronics, right? 2) Solar power: i don't know for sure about this. Sounds like a great idea, too good to be true, honestly. For only 200$ i get 100+w? What are the drawbacks here? 3) UPS: This seems to be the best. The only problem is the cost. Cost < 200$ = great 400$ = budged limit

Search Results

Search found 14443 results on 578 pages for 'virtual keyboard'.

Page 517/578 | < Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524 | Next Page >

- by rhololkeolke

- by Arno2501

- by Parhs

- by Firestrand

- by John N

- by Sebastian Büttner

- by Andrew

- by Taersious

- by Stefan Lasiewski

- by joggink

- by Anthony Aziz

- by Sammy

- by viraptor

- by Kani

- by fostandy

- by user24089

- by karthik

- by Mike Christiansen

- by John Chadwick

- by godDLL

- by Hello71

- by Corey Kennedy

- by Josh Stodola

- by pitseeker

- by Zen 8000k

< Previous Page | 513 514 515 516 517 518 519 520 521 522 523 524 | Next Page >