Search Results

Search found 9332 results on 374 pages for 'an original alias'.

Page 52/374 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• How do I migrate Exchange 2007 to new hardware?

  - by Graeme Donaldson

  As per my previous question, I have an Exchange 2007 box which is also a DC. Since I can't demote it while Exchange is installed, I want to move Exchange to a different server. Does anyone have any articles, tips or experiences to share on this? The last time I did this it was with Exchange 2003 and even that is a little rusty in my head. The setup is a single Exchange 2007 Hub/Edge/Mailbox/CAS server. Its currently on Windows Server 2008, I can migrate it to the same OS, or I can go to 2008 R2, I'm not really picky on that. We're running OWA/ActiveSync/POP3(S)/IMAP(S) for client access. I already have another fully functional DC/GC/DNS box in the same site and clients in the site are already using that for DNS. It's also the preferred site bridgehead for AD replication. Update: After reading Evan's answer I realised that my original question wasn't worded correctly. I'm not looking to do a swing migration, I actually need to move Exchange completely over to a new box. I have done swing migrations in the past, i.e. moving over to a temporary box and back to the original hardware afterwards, and I'm not really sure why I used that term in the original question since it's not what I intended. Any tips?

  Read the article

• Ubuntu second static IP, ifconfig, /etc/network/interfaces

  - by Schmoove

  I would like to add a second static IP to my local Ubuntu 11.10 desktop machine and have it automatically available after rebooting. So far I am successfully using ifconfig to to temporarily set up an alias for my primary network interface: # ifconfig eth1:0 192.168.178.3 up # ifconfig eth1 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.2 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::ca60:ff:feef:a3d9/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:61929 errors:0 dropped:0 overruns:0 frame:0 TX packets:64034 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:45330863 (45.3 MB) TX bytes:28175192 (28.1 MB) Interrupt:42 Base address:0x4000 eth1:0 Link encap:Ethernet HWaddr c8:60:00:ef:a3:d9 inet addr:192.168.178.3 Bcast:192.168.178.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:42 Base address:0x4000 However, when I add the following to /etc/network/interfaces, the alias is not up and running as expected after a reboot: # vi /etc/network/interfaces auto eth1:0 iface eth1:0 inet static address 192.168.178.3 netmask 255.255.255.0 I would like to know what to configure to get this to work. As a side note, I am running gnome shell.

  Read the article

• What to do with a broken OS X install disc?

  - by slhck

  First things first: I don't appreciate software piracy and I really want to spend money on software that I use and that I work and make money with. I don't want this question closed just because I consider downloading software, I only want honest opinions and alternatives. Here we go: So I have my OS X Snow Leopard Upgrade DVD, but it's horribly scratched and won't boot anymore. It endlessly loads and at some point I have to force pull it out of the disc slot. How can I reset my Mac then? Can I take my original disk to an Apple Store and ask them for a replacement? Will they believe me, even if I don't have the receipt anymore? Would owning the original disk make it okay for me to look somewhere on the internet and download it? I don't even know if that will work without hassles. Could I try to read the disk to an image with some error correction methods? Maybe during boot it can't read some files, but some other program can? Is there any other way of resetting the Mac? Mine's now over 3 years old an I seem to have misplaced my original discs that had 10.4 on it. Or should I just buy a new 10.6 upgrade disk? (Which is not really what I want to do) Answers and opinions would be much appreciated.

  Read the article

• Terrible noises from subwoofer of ACER Aspire 6930 with Realtek sound chip

  - by OneWorld

  After approximately 5-15 min of listening to music my subwoofer begins to make terrible noises. He's just "coughing". That began after 6 months I had this computer. Now I found out, that I can temporarily fix this problem by "restarting" the audio stream of the application that plays music. For example reloading last.fm page (reloads the flash file). Another way to reset the audio playback is switching the speaker configuration shown below in the screenshot. According to many posts on the internet like http://www.tomshardware.co.uk/forum/52918-20-acer-aspire-6935g-speaker-problem ACER support isn't any help Exchanging hardware doesn't fix the problem Even the later models have this problem Turning off the volume of the subwoofer is not an option to me. I still have warranty (I bought an extension of one year). I already tried about 15 versions of the Realtek driver with no success. I am not sure but MAYBE the problem did not occur on the original windows vista that was shipped with this computer. However, I removed the original windows for good reasons (english). What do you suggest me? Did anyone fix this problem? Maybe by writing a script which resets the audio streams every 5 minutes? Shall I take the effort to deal with the acer support until they give me another model? (I won't have a computer than for a longer time, will spend money on telephone hotlines (1,30 EUR / min)......) Here are additional infos, if they are any help: Windows 7 64 Bit (Original was Windows Vista Home Premium 32 Bit) All specs Audio driver version:

  Read the article

• Making one of the folders default in Apache

  - by OmerO

  Hello, The file & directory structure of my website is as follows: /Library/WebServer/mysite/joomla .. /Library/WebServer/mysite/wiki .. /Library/WebServer/mysite/forum .. /Library/WebServer/mysite/index.php As you see, there are various applications each residing in separate folders. Now, in order to define this structure, I have made this entry in Apache http-vhosts.config file: ServerName mysite.com DocumentRoot "/Library/WebServer/mysite" ** And I already have the DirectoryIndex defined: DirectoryIndex index.html index.php, and so on. So far so good but I want this specific functionality: When someone visits mysite, he/she should automatically directed to: /Library/WebServer/mysite/joomla (and therefore /Library/WebServer/mysite/joomla/index.php) I don't want to achieve that functionality by putting a redirection code inside /Library/WebServer/mysite/index.php or /Library/WebServer/mysite/index.htm because that causes time delays (because of the redirection, of course) But in this case, the only proper way of achieving it seems to set DocumentRoot this way: DocumentRoot "/Library/WebServer/mysite/joomla" But when I set it that way, then the other folders (/wiki, /forum, etc.) are simply not served by Apache. To work around it, I put directives like: Alias /wiki /Library/WebServer/mysite/wiki .. Alias /forum /library/WebServer/mysite/forum and it did work actually the way I wanted. But... I still cannot use it that way because in this case I just couldn't manage to make the wiki use Short URLs (as described in link text) So, I have to set the DocumentRoot back to /Library/WebServer/mysite and shoud be able to assign /Library/WebServer/mysite/joomla as the "default directory" (my own terminology :) Can I do it in Apache? Is there any other way you might suggest? Thanks.

  Read the article

• nginx reverse proxy to apache mod_wsgi doesn't work

  - by user11243

  I'm trying to run a django site with apache mod-wsgi with nginx as the front-end to reverse proxy into apache. In my Apache ports.conf file: NameVirtualHost 192.168.0.1:7000 Listen 192.168.0.1:7000 <VirtualHost 192.168.0.1:7000> DocumentRoot /var/apps/example/ ServerName example.com WSGIDaemonProcess example WSGIProcessGroup example Alias /m/ /var/apps/example/forum/skins/ Alias /upfiles/ /var/apps/example/forum/upfiles/ <Directory /var/apps/example/forum/skins> Order deny,allow Allow from all </Directory> WSGIScriptAlias / /var/apps/example/django.wsgi </VirtualHost> In my nginx config: server { listen 80; server_name example.com; location / { include /usr/local/nginx/conf/proxy.conf; proxy_pass http://192.168.0.1:7000; proxy_redirect default; root /var/apps/example/forum/skins/; } #error_page 404 /404.html; # redirect server error pages to the static page /50x.html error_page 500 502 503 504 /50x.html; location = /50x.html { root html; } } After restarting both apache and nginx, nothing works, example.com simply hangs or serves index.html in my /var/www/ folder. I'd appreciate any advice to point me in the right direction. I've tried several tutorials online to no avail.

  Read the article

• Keytool and SSL Apache config

  - by Safari

  I have a question about SSL certificate... I have generate a certificate using this keytool command.. keytool -genkey -alias myalias -keyalg RSA -keysize 2048 and I used this command to export the certificate keytool -export -alias myalias -file certificate.crt So, I have a file .crt Now I would to configure my Apache ssl module. I need to use keytool...At the moment I can't to use Openssl How can I configure the module if I have only this certificate.crt file? I see these sections in my ssl.conf # Server Certificate: # Point SSLCertificateFile at a PEM encoded certificate. If # the certificate is encrypted, then you will be prompted for a # pass phrase. Note that a kill -HUP will prompt again. A new # certificate can be generated using the genkey(1) command. #SSLCertificateFile /etc/pki/tls/certs/localhost.crt # Server Private Key: # If the key is not combined with the certificate, use this # directive to point at the key file. Keep in mind that if # you've both a RSA and a DSA private key you can configure # both in parallel (to also allow the use of DSA ciphers, etc.) #SSLCertificateKeyFile /etc/pki/tls/private/localhost.key # Server Certificate Chain: # Point SSLCertificateChainFile at a file containing the # concatenation of PEM encoded CA certificates which form the # certificate chain for the server certificate. Alternatively # the referenced file can be the same as SSLCertificateFile # when the CA certificates are directly appended to the server # certificate for convinience. #SSLCertificateChainFile /etc/pki/tls/certs/server-chain.crt How can I configure the correct section?

  Read the article

• Hyper-V vss-writer not making current copies

  - by Martinnj

  I'm using diskshadow to backup live Hyper-V machines on a Windows 2008 server. The backup consists of 3 scripts, the first will create the shadow copies and expose them, the second uses robocopy to copy them to a remote location and the third unexposes the shadow copies again. The first script – the one that runs correctly but fails to do what it's supposed to: # DiskShadow script file to backup VM from a Hyper-V host # First, delete any shadow copies of the drives. System Drives needs to be included. Delete Shadows volume C: Delete Shadows volume D: Delete Shadows volume E: #Ensure that shadow copies will persist after DiskShadow has run set context persistent # make sure the path already exists set verbose on begin backup add volume D: alias VirtualDisk add volume C: alias SystemDrive # verify the "Microsoft Hyper-V VSS Writer" writer will be included in the snapshot # NOTE: The writer GUID is exclusive for this install/machine, must be changed on other machines! writer verify {66841cd4-6ded-4f4b-8f17-fd23f8ddc3de} create end backup # Backup is exposed as drive X: make sure your drive letter X is not in use Expose %VirtualDisk% X: Exit The next is just a robocopy and then an unexpose. Now, when I run the above script, I get no errors from it, except that the "BITS" writer has been excluded because none of its components are included. That's okay because I really only need the Hyper-V writer. Also I double checked the GUID for the writer, it's correct. During the time when the Hyper-V writer becomes active, 2 things will happen on the guest machines: The Debian/Linux machine will go to a saved state and restore when done, all fine. The Windows guests will "creating vss snapshop-sets" or something similar. Then X: gets exposed and I can copy the .vhd files over. The problem is, for some reason, the VHD files I get over seems to be old copies, they miss files, users and updates that are on the actual machines. I also tried putting the machines in a saved sate manually, didn't change the outcome. I hope someone here has an idea of how to solve this.

  Read the article

• How can I make non-anti-aliased text look good in Firefox on Mac OS X?

  - by cosmic.osmo

  After being a Windows user for the last 10 years, I got a MacBook Pro, which I'm working on configuring to my liking. I find small-size anti-aliased text to be blurry and hard to read, so I typically disable it. I've found the settings in the General Control Panel, and used TinkerTool to increase the anti-alias threshold size to 18pt. Mac OS X and other applications appear to respect these settings. A problem appears when I use Firefox. By default, it's configured to ignore the Mac OS anti-alias settings. This is changed by going to about:config, and setting gfx.use_text_smoothing_setting = true (default is false). However, even with this setting, it appears Firefox is still rendering the fonts under the assumption that they will be anti-aliased, which results in very odd and uneven spacing, as you can see in this example (pay attention to the placement of the "s" in "Disable"): With anti-aliasing: Without anti-aliasing: How can I configure Firefox to both not use anti-aliasing and to use correct font spacing? I'm using Mac OS X Lion and Firefox 5.

  Read the article

• Graphite not running

  - by River

  I'm currently trying to install graphite 0.9.9 on a gentoo box using these instructions from the graphite wiki. Essentially, it fronts graphite using apache and mod_wsgi. Everything seems to have gone well, except that apache / the graphite webapp never seem to return a response to the web browser (the browser continuously waits to load the page). I've turned on the graphite debug info, but the only message in the log files is this, repeated over and over again in info.log (with the pid always changing): Thu Feb 23 01:59:38 2012 :: graphite.wsgi - pid 4810 - reloading search index These instructions have worked for me before to set up graphite on an Ubuntu machine. I suspect that mod_wsgi is dying, but I have confirmed that mod_wsgi works fine when not serving the graphite webapp. This is what my graphite.conf vhost file looks like: WSGISocketPrefix /etc/httpd/wsgi/ <VirtualHost *:80> ServerName # Server name DocumentRoot "/opt/graphite/webapp" ErrorLog /opt/graphite/storage/log/webapp/error.log CustomLog /opt/graphite/storage/log/webapp/access.log common # I've found that an equal number of processes & threads tends # to show the best performance for Graphite (ymmv). WSGIDaemonProcess graphite processes=5 threads=5 display-name='%{GROUP}' inactivity-timeout=120 WSGIProcessGroup graphite WSGIApplicationGroup %{GLOBAL} WSGIImportScript /opt/graphite/conf/graphite.wsgi process-group=graphite application-group=%{GLOBAL} WSGIScriptAlias / /opt/graphite/conf/graphite.wsgi Alias /content/ /opt/graphite/webapp/content/ <Location "/content/"> SetHandler None </Location> # XXX In order for the django admin site media to work you # must change @DJANGO_ROOT@ to be the path to your django # installation, which is probably something like: # /usr/lib/python2.6/site-packages/django Alias /media/ "/usr/lib64/python2.6/site-packages/django/contrib/admin/media/" <Location "/media/"> SetHandler None </Location> # The graphite.wsgi file has to be accessible by apache. It won't # be visible to clients because of the DocumentRoot though. <Directory /opt/graphite/conf/> Order deny,allow Allow from all </Directory> </VirtualHost>

  Read the article

• Prevent Outlook 2010 Insert Picture resizing image

  - by Rup

  When I "Insert Picture" a JPEG in Outlook 2010 it automatically resizes the image and, I think, recompresses it too. I realise this would be useful for photographs or for people who try to email 1MB BMPs but I would like to email around an image at the original pixel size without recompression. Is there a way to turn this off, or better still choose settings for each image insert? I found this page in the Office help. It's for Word, PowerPoint and Excel not Outlook but points you at File, Options, Advanced, Image Settings. There's no equivalent section in Outlook. I know Outlook uses Word as its editor so I've looked at Word's settings but there isn't an 'original size' here: there's only 'turn off image recompression' and pick target DPI from 96, 150, 220. I guess Office is finding a DPI value in the JPEG file and scaling it up or down to match this setting. I can't find an equivalent option in Outlook's options menu but there's so many settings and pop-up dialogs I may have missed something. Picture Format, Reset image size resets the image to the rescaled version, not the original. I can't see a way to edit a pixel value into size values in the image properties after insert. Thanks! I realise I can probably achieve this by editing the image metadata in PhotoShop elements or similar but there ought to be a way without editing the file? This is new behaviour in Outlook 2010; 2007 didn't do this.

  Read the article

• In Icinga (Nagios), how do I configure hosts with multiple IPs?

  - by gertvdijk

  I'm setting up Icinga (Nagios fork) and I have some machines with multiple interfaces. Some services are only listening on one of them and to check them correctly, I like to know if it's possible to have multiple IP addresses configured for a single host in Icinga. Here's a minimal example: Remote Server: eth0: 1.2.3.4 (public IP) eth1: 10.1.2.3 (private IP, secure tunnel) Apache listening on 1.2.3.4:80. (public only) OpenSSH listening on 10.1.2.3:22. (internal network only) Postfix SMTP listening on 0.0.0.0:25 (all interfaces) Icinga Server: eth0: 10.2.3.4 (private IP, internet access) Now if I define a host: define host { use generic-host host_name server1 alias server1.gertvandijk.net address 10.1.2.3 } This will not check the HTTP status correctly. And defining an additional host: define host { use generic-host host_name server1-public alias server1.gertvandijk.net address 1.2.3.4 } will check everything, but shows up as two independent hosts. Now I want to 'aggregate' these two hosts to show up as a single host, yet providing an easy configuration to check the services on their proper address. What is the most elegant number-of-configuration-lines-saving solution to this? I read about several plugins available to workaround this, but I can't figure out what is the current way to address it. Solutions go back to 2003, but I'm running Icinga 1.7.1, already capable of the address6 option, yet that triggers IPv6-only resolving on the hostname... Ideally, I wish to configure Icinga to be intelligent enough to know that the Postfix instance running on 10.1.2.3:25 is the same as 1.2.3.4:25 and thus not triggering two alarms. I guess this must have been tackled before and sysadmins have it set up now. Please share your solution to this. Thanks! :)

  Read the article

• Time Machine is getting stuck at "Preparing to Back Up" and my Trash isn't emptying

  - by zarose

  I have encountered two separate problems, but I am putting them in the same question in case they are related. First, my Trash would not empty. It seems to be getting stuck on certain files, because I will reset my Macbook and some of the files will be deleted, and then if I remove a file or two at random, more can be deleted. Some of these files had strange characters in their names. I tried changing the names to single characters, but this did not help. Next, I attempted to backup my Macbook using Time Machine. I plugged in the HDD I've been using for this, but every time I try to start the backup, Time Machine gets stuck at "Preparing to Back Up". I definitely need to know how to fix the Time Machine problem, but I am curious how to solve the trash problem as well, and whether or not these problems are related. EDIT: Console.app logged the following this morning before I left on a trip. I did not bring the HDD with me. 6/5/12 7:41:28.312 AM com.apple.backupd: Starting standard backup 6/5/12 7:41:46.877 AM com.apple.backupd: Error -35 while resolving alias to backup target 6/5/12 7:41:58.368 AM com.apple.backupd: Backup failed with error: 19 6/5/12 7:59:08.999 AM com.apple.backupd: Starting standard backup 6/5/12 7:59:10.187 AM com.apple.backupd: Backing up to: /Volumes/Seagate 3TB Mac/Backups.backupdb 6/5/12 7:59:13.308 AM com.apple.backupd: Event store UUIDs don't match for volume: Macintosh HD 6/5/12 7:59:13.331 AM com.apple.backupd: Event store UUIDs don't match for volume: Blank 6/5/12 7:59:13.683 AM com.apple.backupd: Deep event scan at path:/ reason:must scan subdirs|new event db| 6/5/12 8:23:31.807 AM com.apple.backupd: Backup canceled. 6/5/12 8:23:33.373 AM com.apple.backupd: Stopping backup to allow backup destination disk to be unmounted or ejected. 6/5/12 9:51:21.572 PM com.apple.backupd: Starting standard backup 6/5/12 9:51:22.515 PM com.apple.backupd: Error -35 while resolving alias to backup target 6/5/12 9:51:32.741 PM com.apple.backupd: Backup failed with error: 19

  Read the article

• Nagios send mail when server is down

  - by tzulberti

  I am using nagios 3.06 to monitor the servers. When a service is critical, it sends a mail, but when a server is down no mail is sent. Even if all the services go to critical state, no mail is sent. I have the following configuration: define command {     command_name notify-host-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$" "******** Nagios ****\n\n Host: $HOSTNAME$\n Description: the server is down" } define command{     command_name notify-service-by-email     command_line python /etc/nagios3/send_mail.py "[Nagios] $HOSTNAME$: $SERVICEDESC$ ($NOTIFICATIONTYPE$)" "***** Nagios *****\n\nNotification Type: $NOTIFICATIONTYPE$\nService: $SERVICEDESC$\nHost: $HOSTALIAS$\nAddress: $HOSTADDRESS$\nState: $SERVICESTATE$\nDate/Time: $LONGDATETIME$\nAdditional Info:$SERVICEOUTPUT$" } The python script is a script to sent a mail. It works if I execute it from the command line, but it doesn't sents an email from nagios. What I am doing wrong? UPDATE: The contact data is: define contact{     contact_name root     alias Root     service_notification_period 24x7     host_notification_period 24x7     service_notification_options w,u,c,r     host_notification_options d,r     service_notification_commands notify-service-by-email     host_notification_commands notify-host-by-email     email [email protected] } define contactgroup{     contactgroup_name admins     alias Nagios Administrators     members root }

  Read the article

• phpmyadmin “Forbidden: You don't have permission to access /phpmyadmin on this server.”

  - by Caterpillar

  I need to modify the file /etc/httpd/conf.d/phpMyAdmin.conf in order to allow remote users (not only localhost) to login # phpMyAdmin - Web based MySQL browser written in php # # Allows only localhost by default # # But allowing phpMyAdmin to anyone other than localhost should be considered # dangerous unless properly secured by SSL Alias /phpMyAdmin /usr/share/phpMyAdmin Alias /phpmyadmin /usr/share/phpMyAdmin <Directory "/usr/share/phpMyAdmin/"> Options Indexes FollowSymLinks MultiViews AllowOverride all Order Allow,Deny Allow from all </Directory> <Directory /usr/share/phpMyAdmin/setup/> <IfModule mod_authz_core.c> # Apache 2.4 <RequireAny> Require ip 127.0.0.1 Require ip ::1 </RequireAny> </IfModule> <IfModule !mod_authz_core.c> # Apache 2.2 Order Deny,Allow Allow from All Allow from 127.0.0.1 Allow from ::1 </IfModule> </Directory> # These directories do not require access over HTTP - taken from the original # phpMyAdmin upstream tarball # <Directory /usr/share/phpMyAdmin/libraries/> Order Deny,Allow Deny from All Allow from None </Directory> <Directory /usr/share/phpMyAdmin/setup/lib/> Order Deny,Allow Deny from All Allow from None </Directory> <Directory /usr/share/phpMyAdmin/setup/frames/> Order Deny,Allow Deny from All Allow from None </Directory> # This configuration prevents mod_security at phpMyAdmin directories from # filtering SQL etc. This may break your mod_security implementation. # #<IfModule mod_security.c> # <Directory /usr/share/phpMyAdmin/> # SecRuleInheritance Off # </Directory> #</IfModule> When I get into phpmyadmin webpage, I am not prompted for user and password, before getting the error message: Forbidden: You don't have permission to access /phpmyadmin on this server. My system is Fedora 20

  Read the article

• Virtualize SBS 2003 - P2V vs migrating to new VM

  - by jlehtinen

  I need to virtualize a SBS 2003 server in my work environment. I need some tips on what people think is the best way to proceed. Background: The SBS 2003 server is the primary DC for the domain and also hosts FTP, RRAS(VPN), DNS, and file shares. Exchange is NOT used, neither is SQL server. DHCP is done via a firewall appliance. I have added a Server 2003 VM to the domain and promoted it to the DC role. AD/DNS is replicating here correctly. This was mainly done to provide fault-tolerance to the domain, I was not intending to make this VM the primary DC. I've already asked about buying upgraded licensing for Server 2008/2012 but was refused due to cost. Options: I see (at least) two routes I could take to complete this. From what I've read option 2 is the "preferred" method, but there's a few steps where I'm not clear on what to expect. Option 1.) P2V the primary DC Power off primary DC Power off secondary DC (to prevent USN rollback in case P2V has issue) P2V (cold clone) primary DC Boot new PDC VM Allow new hardware to detect Remove old NIC hardware from device manager Assign old IPs to new virtual NICs Reboot PDC VM, confirm connectivity and no major issues Power on secondary DC, confirm replication Option 2.) Create new VM, transfer roles, remove original DC from domain Create new VM, install SBS 2003 Do I need the original SBS install discs for this? MS migration doc mentions this. Add VM to domain, promote to DC role Does this start 7 day timer where two SBS servers can be in same domain? Set up RRAS on new VM Set up IIS/FTP on new VM Move file shares to new VM Transfer FSMO roles to new VM DC dcpromo original primary DC out of domain

  Read the article

• Enable SSL with Jetty 8

  - by Jerec TheSith

  I received certificates from GoDaddy an I'm trying to enable SSL with Jetty but receive an error 107 SSL protocol error when connecting to https://server.com:8443 I generated the keystore using these commands : keytool -keystore keystore -import -alias gd_bundle -trustcacerts -file gd_bundle.crt keytool -keystore keystore -import -alias server.com -trustcacerts -file server.com.crt and placed it in /opt/jetty/etc/ And used the following configuration in jetty.xml : <Call name="addConnector"> <Arg> <New class="org.eclipse.jetty.server.ssl.SslSelectChannelConnector"> <Arg> <New class="org.eclipse.jetty.http.ssl.SslContextFactory"> <Set name="keyStore"><SystemProperty name="jetty.home" default="."/>/etc/keystore</Set> <Set name="keyStorePassword">**password1**</Set> <Set name="keyManagerPassword">**password1**</Set> <Set name="trustStore"><SystemProperty name="jetty.home" default="."/>/etc/keystore</Set> <Set name="trustStorePassword">**password1**</Set> </New> </Arg> <Set name="port">8443</Set> <Set name="maxIdleTime">30000</Set> <Set name="Acceptors">2</Set> <Set name="statsOn">false</Set> <Set name="lowResourcesConnections">20000</Set> <Set name="lowResourcesMaxIdleTime">5000</Set> </New> </Arg> </Call> Am I missing something in jetty's configuration ?

  Read the article

• Using awk to split text file every 10,000 lines

  - by Sneaky Wombat

  I have a large gzip'd text file. I'd like to something like: zcat BIGFILE.GZ | awk (snag 10,000 lines and redirect to...)|gzip -9 smallerPartFile.gz the awk part up there, I basically want it to take 10,000 lines and send it to gzip and then repeat until all lines in the original input file are consumed. I found a script that claims to do this, but when I run it on my files and then diff the original to the ones that were split and then merged, lines are missing. So, something is wrong with the awk part and I'm not sure what part is broken. Here's the code. Can someone tell me why this doesn't yield a file that can be split and merged and then diff'd to the original successfully? # Generate files part0.dat.gz, part1.dat.gz, etc. # restore with: zcat foo* | gzip -9 > restoredFoo.sql.gz (or something like that) prefix="foo" count=0 suffix=".sql" lines=10000 # Split every 10000 line. zcat /home/foo/foo.sql.gz | while true; do partname=${prefix}${count}${suffix} # Use awk to read the required number of lines from the input stream. awk -v lines=${lines} 'NR <= lines {print} NR == lines {exit}' >${partname} if [[ -s ${partname} ]]; then # Compress this part file. gzip -9 ${partname} (( ++count )) else # Last file generated is empty, delete it. rm -f ${partname} break fi done

  Read the article

• Western Digital HDD disappears and reappears in BIOS

  - by tbkn23

  I know many people asked about similar problems, but I have a very specific case where I can't understand what's going on... I have a 3TB Western Digital Caviar Green disk connected in my Desktop, that also has a seagate 1.5TB disk and 2 SSD drives (OCZ and Sandisk). After working fine for quite some time (probably more than a year), suddenly my Caviar Green drive disappeared from windows. I checked the BIOS, and it wasn't there either. I opened my PC, played with the connectors, power, etc, but nothing helped. Even tried switching connectors with those of the 1.5TB disk, and nothing changed, the 1.5TB seagate was there, but the 3TB WD was not. Ok, now for the strange part. I have another desktop at home, so I took out my 3TB drive, connected it there, and it worked fine! I copied the most important files out of it, and then made another attempt in the original desktop. Surprise! It now appeared in the BIOS and worked fine! I even ran the SMART test with the WD tools and it said everything was intact. It doesn't end here. After leaving it overnight in the original desktop, it disappeared again in the morning. I repeated the entire process, connecting it to the second desktop, and there it is again working fine. Now for my question... Whats going on? The disk seems to be appearing on/off in my original Desktop, while other drives there work fine. SMART test says the disk is fine. Any ideas? Is the disk defective and should be replaced? Or maybe there's a problem with the controller in the desktop? I'm using a Gigabyte GA-880GA-UD3H motherboard and tried connecting the drive to both bridges (SATA2 and SATA3 bridges). Thanks EDIT: Power options are set never to turn off hard drives:

  Read the article

• EC2 kernel decision and issues with creating a new machine with my AMI

  - by roacha

  I could really use some advice. I started a new instance on EC2 using Amazon's AMI and during the deployment process I selected a Kernel ID of "Use Default". I then configured my server the way that I wanted to and took a snapshot of it. I then created my own AMI to create new servers with. When I try and create a new server with this AMI the server fails to start and I get the error: EXT3-fs: sda1: couldn't mount because of unsupported optional features (240). Which appears to happen because I am selecting a kernel id of "Use default" again when building my second server. I have read that in order for this to work I need to choose the same kernel id that was used in my original server. I have deleted my original server and don't know what it was using. What is the best process to follow in order to not have these issues? Should I choose "Use Default" for my original server? How do you know which kernel it selected? Then should I just document this and always specify this during the deployment of my next servers using my custom AMI? OR should I choose a custom kernel id during the initial build and always use this one moving ahead hoping Amazon never retires it? Thanks for any advice!

  Read the article

• Difficulty restoring a differential backup in SQL Server, 2 media families are expected or no files are ready for rollforward

  - by digiguru

  I have sql backups copied from server A to server B on a nightly basis. We want to move the sql server from server A to server B without much downtime, but the files are very large. I assumed that performing a differential backup and restore would solve the problem with the databases. Copy full backup from server A to copy to server B (10+gb) Open SQL Server Managment Studio on server B Right mouse on databases Restore Database Type in the new DB-name Choose "From Device" and browse to the backup file Click Okay. This is now resorting the original "full" backup. Test new db with dev application - everything works :) On original database rightmouse on DB Tasks Backup... Backup Type = Differential, Backup to disk, add a new file, and remove the old one (it needs to be a small file to transfer for the smallest amount of outage) Copy the diff backup onto the new db Right mouse on DB Tasks Restore Database This is where I get stuck. If I add both the new differential file, and the original backup to the restore process I get an error The media loaded on "M:\path\to\backup\full.bak" is formatted to support 1 media families, but 2 media families are expected according to the backup device specification. RESTORE HEADERONLY is terminating abnormally. But if I try to restore using just the differential file I get System.Data.SqlClient.SqlError: The log or differential backup cannot be restored because no files are ready to rollforward. (Microsoft.SqlServer.Smo) Any idea how to do it? Is there a better way of restoring backups with limited downtime?

  Read the article

• 400 error with nginx subdomains over https

  - by aquavitae

  Not sure what I'm doing wrong, but I'm trying to get gunicorn/django through nginx using only https. Here is my nginx configuration: upstream app_server { server unix:/srv/django/app/run/gunicorn.sock fail_timeout=0; } server { listen 80; return 301 https://$host$request_uri; } server { listen 443; server_name app.mydomain.com; ssl on; ssl_certificate /etc/nginx/ssl/nginx.crt; ssl_certificate_key /etc/nginx/ssl/nginx.key; client_max_body_size 4G; access_log /srv/django/app/logs/nginx-access.log; error_log /srv/django/app/logs/nginx-error.log; location /static/ { alias /srv/django/app/data/static/; } location /media/ { alias /wrv/django/app/data/media/; } location / { proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto https; proxy_set_header Host $http_host; proxy_pass http://app_server; } } I get a 400 error on app.mydomain.com, but the app is published on mydomain.com. Is there an error in my configuration?

  Read the article

• Is it possible to do a 301 redirect AND redirect to the requested resource?

  - by Pure.Krome

  For one of our projects, we're doing a rebranding of the website name, logo, etc... As such, we need to 301 Moved Permenantly redirect all users from the old domain to the new domain. With IIS7, that's pretty simple. We just create a new website that redirects all traffic to a host-headered domain .. to the new one. But this loses their original destination resource. eg. Old Domain: www.OldDomain.com New Domain: www.NewDomain.com User: www.OldDomain.com/user/PureKrome -> 301 --> www.newDomain.com Notice how it's going to the new domain BUT not to /user/PureKrome? How can I do this so it goes to the new domain and keeps the original resource request? I'm guessing URL-ReWriter for IIS7 might help? Also, what happens if I want to do this... CurrentDomain 1: Domain.com CorrectDomain 1: www.Domain.com CurrentDomain 2: AnotherDomain.com CorrectDomain 2: www.AnotherDomain.com Is it also possible to have those in the same IIS website? So any URL to domain.com will 301 to www.domain.com Right now I'm making 2 IIS websites, with a 301 hardcoded (which still means I lose the original resource request, too). Help!

  Read the article

• Can not boot windows XP from cloned hard disk - what can I do?

  - by Martin

  My configuration: a PC (some years old) with MSI K8N-Neo-4F Motherboard, 1 GB RAM. Disk 1 (Maxtor, SATA II, 250 GB): 2 Partitions, on Partition 1 (48 GB): Windows XP Professional (NTFS) on Partition 2 (190 GB): data (NTFS) I wanted to have a larger and faster disk (the PC is incredibly slow and permanently the disk is rattling when I try to open an application or during Windows startup), so I took Disk 2 (Seagate, Sata II, 500 GB), installed in the PC, created at first a 400 GB-partition at the end of the disk and cloned the data to it, which worked well Installed a swap partition and a partition for Ubuntu Linux 12.10 on the first "part" of the disk so I was able to boot Linux and the old Windows XP with the Linux "System selection" at startup. Now I wanted to move Windows XP to the new disk, deleted the Linux partitions cloned Windows XP to the new disk (with free tools - EASESUS), left both disks in the PC and tried to select the new hard drive during boot as boot partition. This did not work, the PC refused to boot from this second disk. I tried many things like making the boot partition on the 2nd drive "active" in the Windows System Preferences modifying the boot.ini file to boot from the second disk - tried to boot from it, but ended with an error message stating that it was not possible to boot from this disk because of a hardware failure or something else or so removing the original disk and plugging the new one on the same SATA port as the original one - also booting failed with an error message repairing the MBR by booting into recovery mode from the Windows XP Installation CD-ROM, selecting the second disk and doing "FIXMBR" which said that everything was fine with the MBR. after that at least the PC tried to boot from the newer disk and then startup was hanging during the blue screen with the Windows Logo.... no luck. ... deleting the cloned partition and cloning again - this time with Macrium Reflect Free version... - no success during booting. I tried a lot of things with no success, so I wonder what I am doing wrong?! What could I do to successfully clone my Win XP partition to replace the original disk by a larger one which is bootable.

  Read the article

• Accessing a webpage folder with .htaccess in it via apache webdav?

  - by pingo

  I have setup webdav access in order to enable an external user to upload the content of his web page to his folder on my server that is served by apache to the web. This way he could update his web page via webdav. Now the problem is that the user requires a .htaccess file and of course .htaccess breaks webdav probably because it overrides settings. (new files cannot be uploaded anymore via webdav if below specified .htaccess exists) I am running Apache2.2.17 and this is my webdav config: Alias /folderDAV "d:/wamp/www/somewebsite/" <Location /folderDAV> Order Allow,Deny Allow from all Dav On AuthType Digest AuthName DAV-upload AuthUserFile "D:/wamp/passtore/user.passwd" AuthDigestProvider file require valid-user </Location> This config is part of my naive solution to fixing this problem. The idea was to specify an alias to the web page folder where webdav would be enabled and then set AllowOverride to none so that the .htaccess would have no effect. Of course I then found out that in <Location /> AllowOverride directive is not valid. The .htaccess file looks like this: #opencart settings Options +FollowSymlinks Options -Indexes <FilesMatch "\.(tpl|ini)"> Order deny,allow Deny from all </FilesMatch> RewriteEngine On RewriteBase / RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule ^(.*)\?*$ index.php?_route_=$1 [L,QSA] ErrorDocument 403 /403.html deny from 1.1.1.1/19 allow from 2.2.2.2 What would be the solution here? I would like to have the web page accessible from the web but at the same time be able to access and modify it via apache's webdav (with digest auth). How would I do that? Also if possible I would like a solution that permits the existence of the .htaccess so that the user still has the power to setup access rules for his web page.

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >