Search Results

Search found 93496 results on 3740 pages for 'email server'.

Page 52/3740 | < Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >

• Windows Server 2008 R2, weird intermittent outgoing connection issues, & Hyper-V Virtual Network

  - by brizz

  My provider says that they run an 'unfiltered' network, so it's not a network issue. Not entirely convinced...but they aren't being very helpful. Basically two days ago started having issues with DNS completely stop working for anywhere between 2-20minutes. This happens roughly every 1-2 hours at least once. I later then found that I am unable to ping ANY external IP address when this is going on. So it's not a DNS issue. Whats even more odd is when this is going on, I STAY connected via RDP, and I can access webpages, etc that are on the server when I access from my home computer. Have tried disabling the firewall--no fix. Have checked Event viewer, the only thing that is there is a warning that DNS has stopped working. I have made no changes/updates to the server. The only thing I have done is add an IP address (don't think it has anything to do with the problem, but wanted to mention everything). Any help/insight/suggestions on how to go about debugging would be much appreciated! update: I am also running Hyper-V, and a virtual network. I just tried pinging (when I have issues), from a Hyper-V machine--and it works, when the main server doesn't.

  Read the article

• Windows 7 Users unable to add Windows 2003 server printers

  - by TravBrack

  Hi there I just rolled out a few Windows 7 x64 machines and ran into this issue where non-admin users are unable to add printers hosted on a windows 2003 server. It works fine on a 2008 server. The issue appears to be with the point and print system. A user will attempt to add the printer, a prompt will come up requiring the user to elevate privileges in order to install a driver, and will fail citing 'access denied'. I found the group policy setting Point and Print Restrictions: When the policy setting is disabled: -Windows Vista computers will not show a warning or an elevated command prompt when users create a printer connection to any server using Point and Print. So I disabled it, verified that the policy was being picked up using rsop, but it still does the same thing. I've also tried the following: Recreating the printers using newer drivers Adding the printer using 32 bit drivers on the 2003 machine, then adding the 64 bit drivers on a Windows 7 machine Adding the printer from a windows 7 machine using print management None of these things work. The security settings are no different than the working printers. Help?

  Read the article

• Setting-up Windows Server 2003 as an L2TP/IPSEC VPN server

  - by andyjohnson

  I'm looking for a pointer to step-by-step instructions for setting-up a Win Server 2003 Std box as a L2TP/IPSEC VPN server. I don't need to use certificates - pre-shared key is sufficient - and the server isn't on a domain. All the sources of information I've found assume a level of sysadmin experience that I don't have - which is why I'm looking for a step-by-step description. I'm a experienced developer, not an IT person, but I have what I'd guess is intermediate level experience of configuring/administering small-scale servers, and have set-up OpenVPN-based VPNs on Windows.

  Read the article

• SQL Server 2005 SP3 on Windows 7 - No Management Studio

  - by Mike Thomas

  I've been trying for a day and a half now to get SQL Server 2005, DEV edition, to work on Windows 7, 64 bit prof. I install from the disk, then run SP 3. I get a failure on the Client Components section of the Installation Progress along with this vague message - Product : Client Components Product Version (Previous): 1399 Product Version (Final) : Status : Failure Log File : C:\Program Files\Microsoft SQL Server\90\Setup Bootstrap\LOG\Hotfix\SQLTools9_Hotfix_KB955706_sqlrun_tools.msp.log Error Number : 1712 Error Description : MSP Error: 1712 One or more of the files required to restore your computer to its previous state could not be found. Restoration will not be possible. I've uninstalled all Visual Studio and tried to make this as clean as possible, and have read a lot of the blog posts, but am really at my wits end about this. I am not a DBA, but I use SQL Server all the time when coding and testing apps. Does anyone have any ideas as to where I can get this sorted out? I've been ati this for a long time and have never encountered an installation as bad as this one. Thanks Mike Thomas

  Read the article

• Windows Server 2008 R2 64bit Screen Frozen and Remote Desktop Freezes but Server Continues Working

  - by Jacques

  I've asked this question a couple of times but I don't seem to be getting any real answers. We have a SBS (Windows Server 2008 Rc) server and suddenly the screen has started freezing. Even when we go into the system via remote desktop it worked once or twice (since the problem started), but now the RDP screen freezes once it gets just past the Welcome screen. The server itself is running, SQL is working, Exchange is working, file share is fine. It's just the UI that isn't working. We've tried hard resetting and that works for a short while before the problem comes back. Where do we begin to resolve this issue? Thanks, Jacques

  Read the article

• VMware Server Host-Only Network Routing

  - by Chris

  I have a windows 2008 web server machine running VMware server. I have 3 VM's - All 3 are test servers so security isn't really a concern... each of them running windows 2008 standard and some of them serving web content. My ISP only allows one MAC address to access the physical switch, however they give me 10 public IP addresses to use. My question is, if I put each VM on their own Host only network, how can I route all traffic from a specific public IP on the host, to the corresponding host only adapter, therefore routing to the specific VM? For example: A single physical Adapter on the Host has the following public IP's assigned to it in windows networking: 74.208.14.10 74.208.14.20 74.208.14.30 Each VM is on a host-only network vm1 - 192.168.196.1 vm2 - 192.168.197.1 vm3 - 192.168.198.1 On the host, I want to route all traffic from 74.208.14.10 to VM1 and 74.208.14.20 to VM2 and 74.208.14.30 to vm3 without using VMware NAT, or bridged connections. I want each server to appear to have its own public IP address. My guess is i can modify the route tables somehow, or perhaps in ICS...but i'm not sure how.

  Read the article

• Separating user resources - Windows Server 2008 (Terminal Server)

  - by Christopher Wilson

  At the moment I am running a Windows Terminal Server 2008 for around 10 clients that use the server to run programs and access data. Is there anyway to separate the resources of each user so that they do not impact each other in terms of resources. User 1: Opens program User 2: Notices slow down I have looked into using Windows System Resource Manager but do not know if it provides what I need and if there are any other 3rd party tools that also provide this functionality. Any answer is appreciated. Server Specs: HP ProLiant ML110 G7 Processor: Intel® Xeon® E3-1220 (4 core, 3.1 GHz, 8MB, 80W, 1333/t) RAM: 12GB DDR3 ECC 1TB HDD

  Read the article

• Possible DNS issue after a reinstall of Windows Server 2000 (get off my lawn)

  - by cop1152

  I just replaced a drive on a Win2000 Server that replicates AD and issues out DHCP at one of our offices. I successfully joined it to the domain, setup range of IP's, etc, but am still having issues. I cannot RDC to it with name or IP. I can ping it, browse to it with Windows Explorer, and remote to it with some other software, but not RDC. The other issue is this: Users are unable to authenticate on it. They receive the message 'username or password incorrect' (or something like that). Changes made on the main domain controller seem to take forever to trickle down. The most significant entry in the DNS Server Log is Event ID 7062: The DNS Server Encountered a Packet Addressed to Itself. At least, I think its significant. The Directory Services Log shows numerous Event IDs 1265: The attempt to establish a replication link with parameters failed with the following status: The DSA operation is unable to proceed because of a DNS lookup failure. Does this make any sense to anyone? I feel like its something very simple that I am overlooking. Thanks in advance.

  Read the article

• How do I install the evaluation version of Windows Server 2012R2 VHD within a Windows Server 2008R2 Hyper-V system?

  - by Paul Hale

  I have a windows server 2008R2 running hyper-v. I have downloaded the Windows Server 2012RC DC Version from here... http://technet.microsoft.com/en-us/evalcenter/dn205286.aspx I am "forced" to install a download app that copy's a .vhd file to my chosen directory. The instructions on this page... http://technet.microsoft.com/library/dn303418.aspx say... To install the VHD Download the VHD file. Start Hyper-V Manager. On the Action menu, select Import Virtual Machine. Navigate to the directory that the virtual machine file was extracted to and select the directory (not the directory where the VHD file is located). Select the Copy the virtual machine option. Confirm that the import was successful by checking Hyper-V Manager. Configure the network adapter for the resulting virtual machine: right-click the virtual machine and select Settings. In the left pane, click Network Adapter. In the menu that appears, select one of the network adapters of the virtualization server, and then click OK. Start the virtual machine. Where it says "Navigate to the directory that the virtual machine file was extracted to and select the directory (not the directory where the VHD file is located). Select the Copy the virtual machine option." Well nothing has been extracted as far as I can tell? and if it has, I have no idea where or what im looking for? I tried creating a new VM and using the downloaded .vhd file but I got an error saying that the .vhd file is an incompatible format. Can anybody help me out please? Thanks, Paul

  Read the article

• Keep printed documents on Windows Server 2008 R2 Print Server

  - by MadBoy

  I've setup Windows 2008 R2 as print server. I have checked option Keep printed document option for all printers and it works fine. Users print their stuff and i can see what they are doing. Problem is everyone sees all documents that are getting printed which is not always the best idea. Is there a way to: Limit print jobs to be only seen by people who printed them and admins Limit print jobs to be only seen on server (from within Server Manager) and so print jobs dissapear when print job is done from user queue (but then admins are still able to see it and track what's printed and when for reporting purposes). Create some kind of access level list so that some people can see everything geting printed, some people see their print jobs and some people see nothing :-)

  Read the article

• Windows Server 2008 R2 DNS Server Intermittently Unresponsive

  - by Ablue

  Throughout the day out DNS servers (2x Win 2k8 R2 servers) are unable to respond to requests. The requests that fail are all on the .root zone that are either cached or obtained from 1 of 5 DNS servers we forward to before going to root hints. At first I thought the DNS servers we were forwarding to were flaky. So I added some more in. Currently the forwarding list looks like ISP DNS 1 OPEN DNS 1 ISP DNS 2 OPEN DNS 2 ISP DNS 3 I have tried: Turning off root hints. Set record scavenging to 7 days. Using dnscmd /config /EnableEDNSProbes 0 as per this. Packet capture at the DNS server shows that there is a lot of query responses with server failure between lan clients and the local dns server; it does not appear to be forwarding those requests. So maybe a problem with caching? Anyhow, does anything have anything I can try to get this working?

  Read the article

• Terminal Server 2008 Login: Access Denied

  - by user1236435

  When I try to RDP into a Server 2008 Terminal Server, I get a message that says "Access Denied" and an OK button. I setup the licensing mode correctly (per user) and also have setup to allow all remote connections. I get the following in the security event log: Log Name: Security Source: Microsoft-Windows-Security-Auditing Date: 28/06/2012 12:01:16 Event ID: 4656 Task Category: File System Level: Information Keywords: Audit Failure User: N/A Computer: 0BraApps1.brenntagLA.hou Description: A handle to an object was requested. Subject: Security ID: BRENNTAGLA\jaadmin Account Name: jaadmin Account Domain: BRENNTAGLA Logon ID: 0xbbe3f Object: Object Server: Security Object Type: File Object Name: C:\Windows\System32\ServerManager.msc Handle ID: 0x0 Process Information: Process ID: 0x60c Process Name: C:\Windows\System32\mmc.exe Access Request Information: Transaction ID: {00000000-0000-0000-0000-000000000000} Accesses: READ_CONTROL SYNCHRONIZE WriteData (or AddFile) AppendData (or AddSubdirectory or CreatePipeInstance) WriteEA ReadAttributes WriteAttributes Access Reasons: READ_CONTROL: Granted by D:(A;;0x1200a9;;;BA) SYNCHRONIZE: Granted by D:(A;;0x1200a9;;;BA) WriteData (or AddFile): Not granted AppendData (or AddSubdirectory or CreatePipeInstance): Not granted WriteEA: Not granted ReadAttributes: Granted by ACE on parent folder D:(A;;0x1301bf;;;BA) WriteAttributes: Not granted Access Mask: 0x120196 Privileges Used for Access Check: - Restricted SID Count: 0 Event Xml: 4656 1 0 12800 0 0x8010000000000000 1535565 Security 0BraApps1.brenntagLA.hou S-1-5-21-205301047-3902605089-2438454170-21511219 jaadmin BRENNTAGLA 0xbbe3f Security File C:\Windows\System32\ServerManager.msc 0x0 {00000000-0000-0000-0000-000000000000} %%1538 %%1541 %%4417 %%4418 %%4420 %%4423 %%4424 %%1538: %%1801 D:(A;;0x1200a9;;;BA) %%1541: %%1801 D:(A;;0x1200a9;;;BA) %%4417: %%1805 %%4418: %%1805 %%4420: %%1805 %%4423: %%1811 D:(A;;0x1301bf;;;BA) %%4424: %%1805 0x120196 - 0 0x60c C:\Windows\System32\mmc.exe Any ideas?

  Read the article

• Intermittent 5.7.1 email bounce to Exchange 2007

  - by Steve Kennaird

  My knowledge of Exchange isn't particularly great, so excuse me if some of the terminology I use isn't quite right. I'm primarily a web developer who's now responsible for a small business's network. We have a server running SBS 2008 and Exchange 2007. Generally, everything works well, emails are able to be sent to both internal and external domains without issue. We've only got ~20 users, Exchange is sitting on a single server. I use SendGrid to send emails generated by our externally hosted website to users in the office. Primarily, order notifications are sent to [email protected]. Without any pattern and less than once per week on average, an email to [email protected] will bounce back, and the logs on SendGrid detail the following error: 550 5.7.1 Unable to relay for [email protected] Either side of that failed delivery attempt, I'm able to send and receive emails to/from [email protected]. Having done some research, incorrect reverse DNS seems like it could be a cause of intermittent bounces like this. Having used nslookup, I have found that the reverse DNS doesn't map like it should, e.g. Office IP: 135.325.351.123 (made up IP, for example only) Domain: office.somedomain.com (made up, for example only) Reverse DNS: somedomain.gotadsl.co.uk (half made up) Could this be a cause? I'm sure that the IP address and the domain should map to each other. Also, it has been suggested to me that as the Exchange server is on a network with an ADSL connection, that could be a potential cause as the connection "goes up and down all day long". I don't have an opinion on this, as I don't have enough knowledge of Exchange/ADSL to form a reliable opinion. Can anyone offer any insight as to whether one or both are actually potential causes, or if there is another possible cause?

  Read the article

• Server 2003 RAS Server Utilising High WAN Traffic

  - by Joe Sergeant

  We have Routing and Remote Access configured on Server 2003 (also our primary domain controller), allowing users to connect in remotely to access files, email, etc. With one user, the RAS Server is constantly sending data to that user's remote computer. From 9am this morning it has transferred almost 800MB. The user isn't transferring any files remotely, certainly not enough to total 800MB anyway. None of the other remote users have had this issue. We have ensured that the user in question has "Use default gateway on remote network" disabled for both IPv4 and IPv6 and we are fairly confident that Offline Files isn't trying to synchronise with the server remotely, too. My question is two-fold. Firstly, has anyone had a similar experience? Secondly, what would be the best software to discover exactly what data is being sent to the remote user?

  Read the article

• SQL Server 2008 R2 Error 15401 when trying to add a domain user

  - by Alice

  I am trying to add a domain user. I am doing the following. Expand Security Right click on Logins Select New Login... Login name select search Click on location and select entire directory Type username Click checkname The name goes underlined and add some more info Click OK Click OK I then get the following error: I have found http://support.microsoft.com/kb/324321. The Login does exist There is no Duplicate security identifiers Authentication failure I don't think is happening as I can browse AD Case sensitivity should not be the problem as I am doing the checkname and it is correcting it. Not a Local account Name resolution again I can see the AD I have rebooted the server (VM) and the issue is still happening. Any ideas? Edit I have also: Domain member: Digitally encrypt secure channel data (when possible) – Disable this policy Domain member: Digitally sign secure channel data (when possible) – Disable this policy Rebooted server http://talksql.blogspot.com/2009/10/windows-nt-user-or-group-domainuser-not.html Edit 2 I have also: Digitally encrypt or sign secure channel data (always)- Disabled Rebooted Edit 3 Since the question have moved site I no longer haves access to comment etc... I have checked the dns on the server to a machine where it is working. The DNS servers are the same on both...

  Read the article

• Quickly set up a Windows Server and automatically install and configure software

  - by Chris

  Yesterday I spent far too much time downloading and installing software on Windows Server 2008. I only had to install a simple server for SQL Server 2008 Express using Microsoft's Web Platform Installer, then configure it to enable remote connections. Everything had to be attended, wasting my time. On a Linux system, this would be trivial to automate, but this is Windows. I do this very rarely, but in the future I would like to make this take as little time as possible. I could do a disc image with everything I installed and configured, but is there a better way? I know nothing of advanced deployment techniques on Windows. Ideally I would like to be able to remotely re-install the OS, or have an unattended install (which I know is possible). Any tips to make the software I need easier to and install and configure with minimal interaction necessary would be helpful. I don't expect everything I asked for to be possible and easy to do. Basically, If any part of it can be done quicker or at least without user input, that's what I'm looking for.

  Read the article

• Window Server 2003 Print spooler

  - by mikenardone

  Hello Everyone in ServerFault, I am new to this website. I have been coming here to fix my own problems. I believe everyone here on this website is great. I could not find this issue anywhere. I am sure that other people had this issue. I have IBM X3850 48GB ram 2 TB of hard drives, four NIC cards. 2 Xeon 1.7 CPU. I am running VMware ESX. I believe that was the paid version if not then it is ESXI. I have 7 Servers on this server. All Window server 2003. On one of the Servers I keep on getting CPU is at 100% . So when I go into task manager and look at the processes that is going on, it is my print spooler. I have 30 different HP laserjet printers and two copiers from HP. I believe it is an driver issue, but I can't figure with one is doing this. Is there any programs for window server 2003 that finds bad print drivers.

  Read the article

• Windows Server 2008 R2 running at a snail's pace

  - by Django Reinhardt

  Really weird problem here. Our main web server has started running at a snail's pace, for absolutely no reason we can discern. Even after restarting the machine, when there's no little or no ram usage and CPU usage is fluctuating between 0 and 30%, simple tasks, like opening Internet Explorer, or waiting for My Computer to open, take forever. There are no processes hogging system resources that we can see... the machine itself is just exhibiting extremely slow behaviour. I've never seen a machine do this. A lot of security updates had built up, so we decided to let Windows install them. When we looked through the history upon restarting, though, they had failed with error code 800706BA. I don't know if this could be related or not. Any help in this matter would be greatly appreciated. As mentioned in the title, we're running a Windows Server 2008 R2 machine. It's also running SQL Server and IIS. It has 16GB of RAM and a decent Quad Core processor. It's also been fine until now -- and we haven't changed a thing. Thanks for any help.

  Read the article

• how to copy sql server database on same server

  - by Sam

  I've got a SQL Server 2008 and want to make a copy of a database so I've got a 2nd Version of the database for testing on the same server. The database copy wizard is not able to copy the database, it always sends funny error Messages about missing objects (using SMO copy). When I try to make a backup and restore it under a different database name it still keeps the file names of the original database and overrides this (crashing the original database). So how do I copy a SQL database? Shutdown SQL Server, copy the physical files and attach them? Maybe a command line tool for database copy? Shouldn't there be an easy way to make a copy?

  Read the article

• Adding a Windows Server 2012 Essentials server to an existing domain, without migrating the AD

  - by TiernanO

  I have an existing Active Directory in house, a mix between a Win2K8R2 and Win2K3 domain, and i would like to test out Windows Server 2012 Essentials BETA on the network. When walking though the install, it gives me the option of a new domain, or migrating from an existing domain. when clicking existing, it tells me i can only have one SBS server running on a domain at a time... So, i dont have any existing SBS servers in house (both are full standard or enterprise editions) but i do plan on keeping at least one of these extra servers running... So, how do i get a 2012 Essentials server to join a domain, and not migrate the existing domain? or if i do migrate, can i still get one of the other boxes to act as secondary controllers?

  Read the article

• Server 2003 and SSL Certificates

  - by Keith Stokes

  I have a Windows 2000 domain with dozens of Windows 2000 servers and a few 2003 servers. Each server runs a custom app talking to a 3rd party utilizing self-signed certificates. To help troubleshooting we've created a custom test app. The 2000 servers are able to talk within seconds. The 2003 servers take anywhere from 10-30 seconds using a domain account and much less, usually under 5 seconds using a local account. The only exception to the local account performance is a new account, which is slow initially then faster. If you leave the test app open and reconnect repeatedly it talks in seconds. If you leave it open for sometime between 1 and 2 hours, it reverts back to the previous 10 seconds, so obviously something is caching. Installing the destination certificates in the local 2003 server store makes no difference. I've installed the certificates in AD and that apparently makes domain accounts work in 9-12 seconds, vs 30 seconds that was regular before. Manually clearing the certificate store on the 2003 server makes no difference. I'm at a loss as to where the certs might be cached and if I'm using some sort of domain certificate store that's hiding from me.

  Read the article

• sql server 2005 instance unresponsive and all db's are 'in recovery'

  - by user44650

  we've got a sql server 2005 instance that one of our guys messed up, i believe they killed the sql server service and restarted the computer, and when it came back all of our databases are "in recovery" and it times out every time we try to connect to it. it's been 'in recovery'and unable to connect to 'msbd' (also in recovery) whenever we try to use SSMC, for the last 4 days now. i'm unsure how to use the DBCC CHECKDB command to check the db integrity. we have backups(which we can't recover from because it keeps timing out), and it's a testing server, so nothing in production is really lost. is there any way to get it out of recovery mode? we have another sqlserver instance running that's just fine, but this instance keeps timing out. the errors i keep seeing are database msdb is being recovered. wait until recovery is finished and an exception occurred while executing a transact-sql statement or batch Timeout expired. any thoughts? we don't really have a DBA here, or anyone with much sql experience.

  Read the article

• Juniper SSG20 IP settings for email server

  - by codemonkie

  We have 5 usable external static IP addresses leased by our ISP: .49 to .53, where .49 is assigned to the Juniper SSG20 firewall and NATed for 172.16.10.0/24 .50 is assigned to a windows box for web server and domain controller .51 is assigned to another windows box with exchange server (domain: mycompany1.com) mx record is pointing to 20x.xx.xxx.51 Currently there is a policy set for all SMTP incoming traffic addressed to .51 forward to the NATed address of the exchange server box (private IP: 172.16.10.194). We can send and receive emails for both internal and external, but the gmail is saying mails from mycomany1.com is not sent from the same IP as the mx lookup however is from 20x.xx.xxx.49: Received-SPF: neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=20x.xx.xxx.49; Authentication-Results: mx.google.com; spf=neutral (google.com: 20x.xx.xxx.49 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] and the mx record in global dns space as well as in the domain controller .50 for mail.mycompany1.com is set to 20x.xx.xxx.51 My attempt to resolve the above issue is to Update the mx record from 20x.xx.xxx.51 to 20x.xx.xxx.49 Create a new VIP for SMTP traffic addressed to 20x.xx.xxx.49 to forward to 172.16.10.194 After my changes incoming email stopped working, I believe it has something to do with the Juniper setting that SMTP addressed to .49 is not forwarded to 172.16.10.194 Also, I have been wondering is it mandatory to assign an external static IP address to the Juniper firewall? Any helps appreciated. TIA

  Read the article

• Script to mirror MS SQL Server databases between 2 servers

  - by David W

  Hi I have about 200 sites each of which have 2 servers running MSSQL (2k5 at some sites, 2k8 at others) One server is production and the other is primarily there as a backup. We're rebuilding all of these servers this year and as part of that we will have to set up mirroring for ... a lot ... of databases. Some of these sites have 45 databases so mirroring them manually is going to be a huge pain. I was going to write a batch script which uses SQLCMD to backup the database and log, copies to the secondary server, restores the backup and log with norecovery, creates the endpoints and sets the partner. This in itself isn't too complicated, but i'd love to see what other people have done as i'm not very confident in catching errors using the process i've outlined above. I've seen Tools to manage sql 2008 database mirroring? Which looks really good, but the formatting is jumbled and I can't get it to work. If anyone has any other scripts they've written and are willing to share I'd be eternally grateful. Ideally I'd love to be able to use a script to ensure there are matching endpoints (same ports) on both servers, backup the database, backup the log, copy the backups to second server, restore database and log with norecovery, set the partners on both servers, and somehow confirm that the databases are linked and synchronized. Well, thanks for reading :)

  Read the article

• Terminal Server CPU usage at 100%

  - by Light1c3

  I'm running a terminal server with around 50-60 users,and every so often the server will go from 40% usage to 100%. I took a closer look an it seems every time this happens, a different user or two seem to be caught in a loop and end up using < 30% where the rest of the users only use a maximum of 5%. The company behind the software we use clame it's due to the servers inadequate hardware (It's a VM system running on a dual - quad core setup) which to me sounds like BS! I'm fairly new to this level of IT so if I misspoke I apologize. I have no way to prove it but I believe adding more raw hardware power wont do me any good as this to me seems like a bug in their software, and it will suck up as much ( or little) CPU as it's given. The VM in question has 4 vCPU cores and 12 GB RAM available, and is running Windows Server 2008, 64-bit Thanks in advance for your help! Note: I have the same question posted on SO, but was pointed in this direction so just in case, here is a link to the post http://stackoverflow.com/questions/17276602/termserver-cpu-at-100

  Read the article

< Previous Page | 48 49 50 51 52 53 54 55 56 57 58 59  | Next Page >